Current through Register 2024 Notice Reg. No. 38, September 20, 2024
(a)
Purpose. Require engine
manufacturers to provide a label to the SPMV manufacturer and require SPMV
manufacturers to apply the certified engine label and the SPMV label to the
SPMV with information needed to properly maintain certified engine
packages.
(b)
Applicability.
(1) All
certified engine packages must comply with these labeling
requirements.
(2) The
responsibility for compliance with this section rests with the engine
manufacturer and SPMV manufacturer, as applicable.
(c)
Label Requirements for certified
engine package.
(1) Engine
Identification number. The engine manufacturer must permanently identify a
certified engine package by direct stamping or embossment on the engine block.
The identification must be readily visible and readable using block text that
is a minimum of 2 millimeters in height, and resistant to heat, cold, or
corrosive materials. A visual sample of the identification must be submitted in
the application for certification.
(2)
Emissions Control Label.
(A) The engine manufacturer must provide a
label with each certified engine package to the SPMV manufacturer to be affixed
to a fully assembled vehicle. Engine manufacturers must provide instructions to
the SPMV manufacturer to affix the label in such a manner that it cannot be
removed without destroying or defacing the label and shall not be affixed to
any part that is likely to be replaced during the vehicle's useful life.
1. The labels on 2019 through 2021 MY
certified engine packages that are certifying to the LEV II exhaust emission
standards in sections
2209.2.(d)(1)(A) and
2209.2.(d)(3)(A) must comply with "California 2015 and Subsequent Model
Criteria Pollutant Exhaust Emission Standards and Test Procedures and 2017 and
Subsequent Model Greenhouse Gas Exhaust Emission Standards and Test Procedures
for Passenger Cars, Light-Duty Trucks, and Medium-Duty Vehicles," last amended
September 2, 2015, which are incorporated by reference herein. The applicable
section in each of the above cited exhaust emission standards and test
procedures is part 1, subpart C, section 3, which incorporates by reference and
amends 40 CFR 86.1807 "Vehicle Labeling."
2. The labels on 2019 and subsequent MY
certified engine packages that are certifying to the LEV III exhaust emission
standards in sections
2209.2.(d)(1)(A),
2209.2.(d)(2)(A), 2209.2.(d)(3)(B), and 2209.2.(d)(4)(A) must comply with
"California 2015 and Subsequent Model Criteria Pollutant Exhaust Emission
Standards and Test Procedures and 2017 and Subsequent Model Greenhouse Gas
Exhaust Emission Standards and Test Procedures for Passenger Cars, Light-Duty
Trucks, and Medium-Duty Vehicles," last amended September 2, 2015, which are
incorporated by reference herein. The applicable section in each of the above
cited exhaust emission standards and test procedures is part 1, subpart C,
section 3, which incorporates by reference and amends 40 CFR 86.1807"Vehicle
Labeling."
(B) Additional
Label Requirements: The label must also contain the following sentence lettered
in the English language in block letters and numerals which must be of a color
that contrasts with the background of the label: "This engine is intended only
for use in a SPMV, as defined in section
2209.1, Title 13, California Code
of Regulations."
1. New
section filed 8-5-2019; operative 10-1-2019 (Register 2019, No.
32).
Note: Authority cited: Sections 39600, 39601, 43000,
43100, 43101, 43102, 43104 and 43105, Health and Safety Code. Reference:
Sections 39002, 39003, 43000, 43100, 43101, 43102, 43104, 43105, 43106 and
43205, Health and Safety Code; and Section 580, Vehicle
Code.