California Code of Regulations
Title 13 - Motor Vehicles
Division 3 - Air Resources Board
Chapter 1 - Motor Vehicle Pollution Control Devices
Article 2 - Approval of Motor Vehicle Pollution Control Devices (New Vehicles)
Section 1962.5 - Data Standardization Requirements for 2026 and Subsequent Model Year Light-Duty Zero Emission Vehicles and Plug-in Hybrid Electric Vehicles

Universal Citation: 13 CA Code of Regs 1962.5

Current through Register 2024 Notice Reg. No. 38, September 20, 2024

(a) Applicability. The requirements of this section shall apply to light-duty zero emission vehicles (ZEV) and plug-in hybrid electric vehicles (PHEV) certified for sale in California as follows:

(1) At least 40 percent of a manufacturer's 2026 model year ZEVs and 100 percent of a manufacturer's 2027 and subsequent model year ZEVs shall meet the requirements of this section.

(2) At least 40 percent of a manufacturer's 2026 model year PHEVs and 100 percent of a manufacturer's 2027 and subsequent model year PHEVs certified to earn vehicle values in accordance with title 13, California Code of Regulations (CCR), section title 13, California Code of Regulations (CCR), section title 13, California Code of Regulations (CCR), section 1962.4 shall meet the requirements of subsections (c)(4)(A)2., (c)(4)(A)4.c. through (c)(4)(A)4.e., and (c)(6).

(3) The phase-in percentages of subsections (a)(1) and (a)(2) shall be based on the manufacturer's projected sales volumes for all ZEVs and for all PHEVs projected to be certified to earn vehicle values in accordance with title 13, CCR, 1962.4, respectively. Manufacturers shall submit phase-in plans demonstrating compliance with these percentage requirements prior to submittal of a certification application to the California Air Resources Board (CARB) for any 2026 model year vehicle. Such phase-in plans shall include planned ZEV and applicable PHEV models, projected sales for each model, designation of which models will be complying with the applicable requirements of subsections (a)(1) or (a)(2), and calculation of the resultant phase-in percentages.

(4) A manufacturer may utilize an alternative phase-in to the required phase-in of subsection (a)(1) or (a)(2) as long as it satisfies the following two requirements:

(i) the total compliance calculation for the alternative phase-in schedule according to the method below must sum to be equal to or greater than 180 by the end of the 2027 model year, and

(ii) 100 percent of the manufacturer's vehicles subject to the phase-in must meet the requirements of this section in 2028 and subsequent model years. The total compliance calculation for the alternative phase-in is the percent of vehicles meeting the requirements of this section in a given model year per the phase-in plan required in subsection (a)(3), multiplied by 3 for the 2025 model year, by 2 for the 2026 model year, and by 1 for the 2027 model year, and then summed together. A manufacturer is not permitted to utilize 2024 and earlier model year vehicles to satisfy the total compliance calculation requirements of the alternative phase-in described in this subsection.

(5) In lieu of the required phase-ins in subsections (a)(1) and (a)(2) or the alternative phase-ins allowed in subsection (a)(4), small volume manufacturers may meet the respective ZEV and PHEV requirements on all 2028 and subsequent model year vehicles.

(b) Definitions: For this section, the following definitions apply in addition to the definitions in title 13, CCR, section 1962.4, and associated test procedures:

"Grid energy", for the purposes of tracking grid energy into the battery parameters in subsection (c)(4)(D), means all energy into the battery while connected to grid power (e.g., plugged-in). Grid energy into the battery shall not include electrical losses between the grid and the battery (e.g., from onboard charger inefficiency) or energy directly used by the vehicle without first going into the battery (e.g., electricity utilized directly from before or after the on-board charger to power on-vehicle devices for cabin conditioning, charging control, etc.). For the purposes of tracking the alternating current power into the vehicle or on-board charger from off-board charging parameter in subsection (c)(4)(D), "grid energy" means all energy supplied to the on-board charger.

"Propulsion-related part" means any original equipment system, component, or part whose failure will directly impede the ability on a zero-emission vehicle to refuel or recharge the vehicle, store fuel or energy for the vehicle, propel the vehicle, including delivering torque to the wheel and tire assembly excluding the wheel and tire assembly itself, or recover or recoup vehicle kinetic energy, including components used to control, manage, or thermally manage such propulsion components. These include vehicle high voltage batteries, drive motors, wheel motors, inverters, converters, on-board charging system components, fuel cell stack components, refueling and fuel tank components, fuel cell air and fuel delivery components, regenerative braking system components, and the power electronics, electronic control units, and thermal management systems of such components and systems providing propulsion, thermal management, recharging and energy storage, conversion, and related diagnosis within the vehicle. Advanced driver assistance systems and safety-related components and systems are not considered "propulsion-related parts" for the purpose of this regulation.

"Propulsion system active" is the state where the powertrain (e.g., electric machine) is enabled by the driver (e.g., after the power button is pushed for some vehicles, remote activation to precondition the cabin) such that the vehicle is ready to be used (e.g., vehicle is ready to be driven, ready to be shifted from "park" to "drive", heating, ventilation, and air conditioning (HVAC) turned on to condition cabin prior to driving). For purposes of this definition, "the state where the powertrain is enabled" does not include activations that are not driver-initiated (e.g., conditions where portions of the vehicle system wake up to perform off-board charging).

(1) Reference Documents: The following documents are incorporated by reference into this regulation:

(A) SAE J1962: SAE J1962 "Diagnostic Connector", July 2016 (SAE J1962).

(B) SAE J1979-3, "E/E Diagnostic Test Modes: Zero Emission Vehicle Propulsion Systems on UDS (ZEVonUDS)", published draft June 20, 2022 (SAE J1979-3).

1. SAE J1979-DA, "Digital Annex of E/E Diagnostic Test Modes", April 2021 (SAE J1979-DA).

1. SAE J2012DA_201812 "Digital Annex of Diagnostic Trouble Code Definitions and Failure Type Byte Definitions", December 2018 (SAE J2012-DA).

(D) ZEV Test Procedures--California Test Procedures for 2026 and Subsequent Model Year Zero-Emission Vehicles and Plug-In Hybrid Electric Vehicles, in the Passenger Car, Light-Duty Truck and Medium-Duty Vehicles Classes, dated August 25, 2022.

(2) Diagnostic Connector:

(A) A standard data link connector conforming to the "Type A" specifications and in the location specified for "Type A" connectors in SAE J1962 shall be incorporated in each vehicle.

(B) The vehicle connector mounting feature shall withstand a force of 220 Newtons applied to the connector mating area in the direction of the connecting and disconnecting process without mechanical and electrical failure. It shall also withstand a force of 220 Newtons applied in all other axial directions without mechanical failure.

(C) The connector may not be covered in any way (e.g., may not be covered by a removable panel, dust cap, lid, flap, door).

(D) Any pins in the connector that provide electrical power shall be properly fused to protect the integrity and usefulness of the connector for diagnostic purposes and may not exceed 20.0 Volts direct current (DC) regardless of the nominal vehicle system or battery voltage.

(E) Manufacturers may not equip vehicles with additional diagnostic connectors in the driver's side foot-well region of the vehicle interior in the area bound by the driver's side of the vehicle and the driver's side edge of the center console (or the vehicle centerline if the vehicle does not have a center console) if the additional connectors can be mated with SAE J1962 "Type A" external test equipment.

(3) Communications to a Scan Tool: For ZEVs, manufacturers shall use one of the following standardized protocols for communication to a scan tool of all required messages. Only one protocol per vehicle shall be used to report all required messages. For PHEVs subject to reporting the data parameters identified in subsection (c)(4)(A)2. in accordance with subsection (a)(2), manufacturers shall report these data using the same standardized protocol for communication to a scan tool of all required messages used by the PHEV to comply with title 13, CCR, section 1968.2(g) in lieu of the requirements of subsections (c)(2) through (c)(4) of this regulation referencing the use of SAE J1979-3.

(A) SAE J1979-3 "UDSonCAN". The vehicle shall utilize unified diagnostic services (UDS) on a controller area network (CAN) as defined in SAE J1979-3. The vehicle shall respond to functional (i.e., broadcast) and physical (i.e., point-to-point) request messages from a scan tool in accordance with SAE J1979-3 specifications except for Service $14 (i.e., clear/reset diagnostic information) where the vehicle shall respond to functional and may respond to physical request messages from a scan tool.

(B) SAE J1979-3 "UDSonIP". The vehicle shall utilize UDS on an internet protocol (IP) network as defined in SAE J1979-3.

(4) Required Functions: The following standardized functions shall be implemented in accordance with the specifications in SAE J1979-3 for the communication protocol used by the vehicle per subsection (c)(3) to allow for access to the required information by a scan tool. These functions and data shall be accessible by a scan tool user and scan tool without the use of any vehicle manufacturer-specific, user-specific, or tool-specific registration, authentication, authorization, login, password, certification, or other mechanism that can be used to restrict or limit user or tool access for any other reason.

(A) Data Stream: The following signals shall be made available on demand through the standardized data link connector in accordance with SAE J1979-3 and SAE J1979-DA specifications. The actual signal value shall always be reported instead of a default or limp home value that the vehicle manufacturer may have chosen to substitute in place of the actual signal by the receiving onboard electronic control for use by it or other onboard electronic control units.

1. For all ZEVs:

a. vehicle speed, absolute accelerator pedal position, time elapsed since start of trip, odometer reading, distance traveled since fault memory last cleared, and number of propulsion system active trips since fault memory last cleared

b. high voltage battery pack: state of charge, maximum cell voltage, minimum cell voltage, battery system voltage, cumulative battery system current for the last 1 second, cumulative battery system energy (i.e., power via integrated voltage times current) consumption for the last 1 second

2. Additionally, for all off-board charge capable vehicles:

a. High voltage battery pack: state of health (SOH), distance traveled since SOH last updated or reset, quantity of battery energy remaining in reserve (only required for vehicles designed to initially hold some battery capacity or energy in reserve and open up access as the vehicle or battery ages)

b. actual rate of charge occurring (e.g., kilowatt rate of grid energy into the vehicle from off-board source), maximum rate of charge the vehicle can accept in its current state (e.g., given the condition of the vehicle at the time of charging such as battery temperature and state of charge, the maximum kilowatt rate the vehicle would accept if the off-board source had unlimited power capability)

3. Additionally, for all vehicles equipped with a fuel cell system: cumulative hydrogen fuel consumed by the fuel cell system in the last 1 second, fuel cell system voltage, cumulative fuel cell system generated current for the last 1 second, and cumulative fuel cell system electrical energy (i.e., power via integration of voltage times current) generated from hydrogen for the last 1 second. Reported fuel cell system current, voltage, and electrical energy shall represent the values at the output of any boost convertor or similar power conditioning device that receives electricity from the fuel cell stack and in turn provides conditioned power to the vehicle motors, battery, or other vehicle loads.

4. Accuracy

a. For purposes of the data stream parameters, manufacturers shall report the most accurate values that are calculated within electronic control units on the vehicle.

b. For cumulative battery system current and battery system energy and for cumulative fuel cell system current and fuel cell system electrical energy, manufacturers shall use current and voltage measurements at a sampling rate of no less than 20 hertz to calculate cumulative current and power for the last 1000 milliseconds, and those cumulative values shall be updated at a minimum frequency of 1 hertz.

c. For the high voltage battery SOH parameter, manufacturers shall ensure the reported value is normalized from 0 to 100 percent and correlates to the usable battery energy for the certification range value as measured in accordance with the ZEV Test Procedure as applicable. The reported SOH parameter shall be no more than 5 percentage points higher than the SOH value that corresponds to the measured usable battery energy.

d. For vehicles designed to initially hold some battery capacity or energy in reserve and open up access as the vehicle or battery ages (e.g., to widen the minimum and maximum allowed state of charge as the battery degrades to counteract or diminish reduction in battery usable energy), manufacturers shall meet the requirements of subsection (c)(4)(A)4.c., except that the reported battery SOH parameter shall be normalized such that 100 percent reflects the usable battery energy as if the user was allowed to initially access the maximum the system is designed to ever allow (e.g., a vehicle with a new battery but with the reserve in the system artificially opened up to its maximum range of authority). Within 10 days upon request by the Executive Officer, the manufacturer shall provide software or other means for CARB to conduct verification testing to ensure the accuracy of the SOH parameter to the measured usable battery energy as required by this section. The manufacturer shall provide any physical items to CARB at the following address: Chief, Emissions Certification and Compliance Division, CARB, 4001 Iowa Ave, Riverside, California 92507, and may provide information or code electronically upon mutual agreement as provided under sections 1633.7 and 1633.8 of the Civil Code.

e. The manufacturer may limit calculation of an updated battery SOH parameter to certain usage conditions of the vehicle (e.g., only when a sequence of sufficient depth of discharge and subsequent charge event occurs) if necessary to maintain the accuracy of the data parameter within the requirements of subsection (c)(4)(A)4.c. above. However, a manufacturer may only use conditions which are technically necessary to ensure robust calculation of the battery SOH parameter, designed to ensure calculation of an updated value will occur under conditions which may reasonably be expected to be encountered in normal urban vehicle operation and use, and designed to ensure calculation of an updated value will occur for vehicles in a test group, on average, at least once every 4,000 miles.

(B) Fault Codes.

1. For all monitored propulsion-related parts and systems, fault codes and fault code status shall be made available through the diagnostic connector in accordance with SAE J1979-3, SAE J2012, and SAE J2012-DA specifications.

2. For all monitored propulsion-related part and system fault codes, the vehicle shall clear diagnostic information and fault codes through a standardized request through the diagnostic connector in accordance with SAE J1979-3 specifications.

1. Test Group Identification: On all vehicles, the test group designation pursuant to title 13, CCR, section 1962.4(i) used for certification to CARB standards shall be made available through the standardized data link connector in accordance with the SAE J1979-DA specifications. Only one electronic control unit per vehicle shall report the test group.

2. Software Calibration Identification: For each propulsion-related control unit that reports data required by subsections (c)(4)(A), (c)(4)(B), or (c)(4)(D), a software calibration identification number(s) (CAL ID) capable of identifying the version of software being used by the control unit(s) shall be made available through the standardized data link connector in accordance with the SAE J1979-DA specifications. A unique CAL ID shall be used for every propulsion-related calibration or software set having at least one bit of different data from any other propulsion-related calibration or software set.

3. Vehicle Identification Number: All vehicles shall have the vehicle identification number (VIN) available through the standardized data link connector in accordance with SAE J1979-DA specifications. Only one electronic control unit per vehicle shall report the VIN.

4. Electronic Control Unit (ECU) Name: The name of each propulsion-related ECU that reports data required by subsections (c)(4)(A), (c)(4)(B), (c)(4)(C)1. through (c)(4)(C)3., or (c)(4)(D) shall be communicated in a standardized format in accordance with SAE J1979-DA.

(D) Vehicle Operation Tracking Requirements:

1. Manufacturers shall implement software algorithms to individually track and report the following in a standardized format in accordance with SAE J1979-3 and SAE J1979-DA:

a. Total distance traveled

b. Total number of propulsion system active trips (where a trip is satisfied whenever the propulsion system active state has been met for at least two seconds plus or minus one second)

c. Total positive kinetic energy

d. Total electric motor output energy

e. Total propulsion system active time

f. Total idle propulsion system active time (where idle is defined as accelerator pedal released by driver and vehicle speed less than or equal to 1.6 kilometers per hour)

g. Total city propulsion system active time (where city is defined as vehicle speed greater than 1.6 kilometers per hour and less than or equal to 60 kilometers per hour)

h. Total fuel cell system active time (if equipped with a fuel cell system), defined as the total time in which the fuel cell stack consumes hydrogen and generates electricity in any mode of operation

i. Total fuel cell system energy generated (if equipped with a fuel cell system)

j. Total hydrogen fuel consumed (if equipped with a fuel cell system)

k. Total net battery current in the state of propulsion system active

l. Total net energy consumed in the state of propulsion system active

m. Total energy into battery (e.g., from regenerative braking) during the state of propulsion system active

n. Total grid energy into the battery during off-board charging

o. Total grid energy into the battery from off-board DC charging

p. If equipped with the capability to determine alternating current (AC) power into the vehicle or onboard charger during off-board charging, total grid energy into the vehicle from off-board AC charging

q. Total battery energy supplied to an off-board usage (e.g., grid, power port) during propulsion system non-active operation (e.g., vehicle to home)

r. Average battery temperature during charging, during propulsion system active, and, if equipped, during non-usage of the vehicle (i.e., non-propulsion system active, non-charging)

s. Total time at low, mid, and high state of charges where total time includes cumulative time during propulsion system active, time during charging, and, if equipped, time during non-usage of the vehicle (i.e., non-propulsion system active, non-charging)

t. Total number of charge events following a low, medium, or high depth of discharge of the battery

2. Numerical Value Specifications: For each data parameter specified in subsection (c)(4)(D)1., the value shall be stored twice, one representing the lifetime of the vehicle and the second representing recent operation in accordance with SAE J1979-DA specifications. If any of the individual lifetime values reach the maximum value defined in SAE J1979-DA, all lifetime values shall be divided by two before any are incremented again to avoid software overflow problems.

3. For data parameters specified in subsection (c)(4)(D), CARB, or a third party contracted directly by CARB, may not collect data from vehicles owned or leased by a private individual unless the data is obtained with the voluntary and informed consent of the vehicle operator.

(5) Data Reporting Requirements for Over-the-Air Reprogramming

(A) The manufacturer shall collect all lifetime values stored in the vehicle pursuant to subsection (c)(4)(D) prior to over-the-air reprogramming of any control module, if any such data would be erased by such reprogramming.

(B) For any data collected pursuant to subsection (c)(5)(A), the manufacturer shall submit a report to the Executive Officer containing the average value and standard deviation of each collected data parameter for each affected certified test group as specified in "Data Record Reporting Procedures for Over-the-Air Reprogrammed Vehicles and Engines Using SAE J1979-2", dated December 15, 2021, and incorporated by reference. The manufacturer shall submit a separate report for each unique calibration/software update. The manufacturer shall submit the report within 75 calendar days of the availability of the calibration/software update to affected vehicles.

(6) Display of Data to the Vehicle User

(A) Each vehicle shall also be able to display the battery SOH parameters in subsection (c)(4)(A)2.a. above, in vehicle, to the vehicle user without the use of any tools.

(B) Each vehicle shall also be able to display the charge rate parameters in subsection (c)(4)(A)2.b. above, in vehicle, to the vehicle user during charging without the use of any tools.

1. readable by the user with no more than 5 selectable screens or submenu selections needed to access the parameter from the home or default display/screen;

2. in alphanumeric format;

3. displayed with the same resolution as the standardized data parameter; and

4. converted to standard engineering units, as applicable (e.g., percent, miles, kilowatts).

(d) Certification Documentation. The manufacturer shall submit documentation related to the requirements of this section in the manufacturer's certification application in accordance with title 13, CCR, section 1962.4(i).

(e) Production Vehicle Verification of Standardized Requirements.

(1) Manufacturers shall perform testing to verify that all vehicles certified pursuant to CCR, title 13, section 1962.4, meet the requirements of subsections (c)(3) and (c)(4) of this section.

(2) Selection of Test Vehicles: Manufacturers shall perform this testing every model year on one production vehicle for every unique calibration no later than 60 days after the start of normal production for that calibration. Manufacturers may request Executive Officer approval to group multiple calibrations together and test one representative calibration per group, and may provide documentation to support such request. The Executive Officer shall approve the request upon finding that the software designed to comply with the standardization requirements of subsection (c) in the representative calibration vehicle is identical (e.g., communication protocol message timing, number of supported data stream parameters) to all others in the group and that any differences in the calibrations are not material with respect to meeting the criteria in subsection (e)(3). The Executive Officer shall notify a manufacturer in writing of the approval or denial of such request within 30 days of receiving the request.

(3) Test Equipment: For the testing required in this subsection (e), manufacturers shall utilize an off-board device to conduct the testing. At least 30 days prior to conducting testing, manufacturers are required to request Executive Officer approval of the off-board device that the manufacturer will use to perform the testing. As part of their requests, manufacturers shall include data, specifications, or engineering analysis that demonstrate that the off-board device will verify vehicles' ability to perform all of the required functions in subsection (e)(4) for the specific vehicle in accordance with SAE J1979-3 specifications. The Executive Officer shall approve the request upon determining that the manufacturer has submitted such data, specifications, or engineering analysis. The Executive Officer shall notify a manufacturer in writing of the approval or denial of such request within 30 days of receiving the request.

(4) Required Testing:

(A) The testing shall verify that the vehicle can properly establish communications between all propulsion-related onboard computers and any scan tool designed to meet the communication protocols allowed in subsection (c)(3);

(B) The testing shall further verify that the vehicle can properly communicate the following information in accordance with SAE J1979-3 and SAE J1979-DA specifications:

1. All data stream parameters required in subsection (c)(4)(A) including the identification of each data stream parameter as supported;

2. The vehicle identification information in subsection (c)(4)(C);

3. All vehicle operation tracking data parameters required in subsection (c)(4)(D); and

4. Any fault code (including failure type byte and status byte) required in subsection (c)(4)(B)1. for a propulsion-related electronic powertrain control unit designed to report such fault codes.

(C) The testing shall also verify that the vehicle can properly respond to a request to clear propulsion-related fault codes as required in subsection (c)(4)(B)2.

(5) Reporting of Results:

(A) The manufacturer shall notify the Executive Officer within 30 days of identifying any vehicle that does not meet one or more of the requirements of subsection (c)(4). The manufacturer shall submit a written report describing the problem(s) identified to the Executive Officer. The written report shall include proposed corrective action to remedy the problem(s), including an implementation timeframe, for the Executive Officer's approval. Factors to be considered by the Executive Officer in approving the proposed corrective action shall include the severity of the problem(s), the ability of service technicians to access the required information, the ability of CARB to access the information needed to conduct vehicle testing, the impact on equipment and tool manufacturers, and the amount of time between identification of the problem(s) and implementation of the proposed corrective action. The Executive Officer shall notify the manufacturer in writing within 30 days of receiving the written report whether the proposed corrective action is approved.

(B) For any vehicle that meets all the requirements of subsection (e)(4), the manufacturer shall submit a report of the test results and the test log file to the Executive Officer within 90 days of that vehicle's testing.

(f) Electronic submittal. Unless otherwise specified, reports, documentation, and requests under this Section must be provided to CARB through the electronic Document Management System available through the website: https://arb.ca.gov/certification-document-management-system.

(g) Deficient Requirements. For 2026 through 2029 model year vehicles, the Executive Officer, upon receipt of a certification application from the manufacturer, shall certify vehicles, even though said vehicles may not comply with one or more of the requirements of subsections (c)(4)(A)1., (c)(4)(A)3., (c)(4)(C), or (c)(4)(D)1., under the following conditions. The Executive Officer shall grant certification for 2026 and 2027 model year vehicles that meet at least 50 percent, 2028 model year vehicles that meet at least 70 percent, and 2029 model year vehicles that meet at least 90 percent of the total number of applicable individual requirements within subsections (c)(4)(A)1., (c)(4)(A)3., (c)(4)(C), and (c)(4)(D)1. For purposes of this calculation, each separately numbered subsection shall count as an individual requirement (e.g., (c)(4)(A)1.b., (c)(4)(D)1.g.) if it is applicable to the vehicle (e.g., (c)(4)(D)1.h. only counts as an individual requirement for fuel cell electric vehicles). The deficient requirements do not need to be included in any written report pursuant to subsection (e)(4)(D)1., provided the manufacturer submitted a list of deficient requirements as part of its certification application per CCR, title 13, section 1962.4(i)(3)(L).

(h) Enforcement.

(1) In addition to any other failure to meet a requirement of this section, submitting incorrect information, or failing to submit required information, is a violation of this section for which violators are subject to penalty as provided by law. Each failure to comply, including each incorrect or omitted statement in a submission to the Executive Officer is a separate violation of this section. A manufacturer is subject to penalties as provided by law, including those authorized under Health and Safety Code section 43016 and 43212, for any violations of the requirements of this section.

(2) CARB shall conduct any compliance testing, enforcement testing, determination of noncompliance, and subsequent corrective action in accordance with title 13, CCR, section 1962.7.

(3) For any vehicle requirements under this section that are not subject to testing, determination of nonconformance, and corrective action under title 13, CCR, section 1962.7, failure to comply is subject to corrective action, including recall of vehicles, under title 13, CCR, section 2109.

(i) Severability. Each provision of this section is severable, and in the event that any provision of this section is held to be invalid, the remainder of this section and this article remains in full force and effect.

1. New section filed 11-30-2022; operative 11-30-2022 pursuant to Government Code section 11343.4(b)(3) (Register 2022, No. 48).

Note: Authority cited: Sections 38510, 38560, 38580, 39039, 39600, 39601, 39602.5, 43006, 43013, 43016, 43018, 43023, 43100, 43101, 43104, 43105.5, 43106, 43154, 43211, 43212 and 44036.2, Health and Safety Code. Reference: Sections 38501, 38510, 38560, 38580, 43006, 43013, 43018, 43023, 43100, 43101, 43102, 43104, 43106, 43154, 43211 and 43212, Health and Safety Code; Sections 1633.7 and 1633.8, Civil Code; and Engine Manufacturers Association v. State Air Resources Board (2014) 231 Cal.App.4th 1022.

Disclaimer: These regulations may not be the most recent version. California may have more current or accurate information. We make no warranties or guarantees about the accuracy, completeness, or adequacy of the information contained on this site or the information linked to on the state site. Please check official sources.

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.