Current through Register Vol. 49, No. 9, September, 2024
c) Definitions:
1) AOGC: Arkansas Oil and Gas
Commission.
2) ADEQ: Arkansas
Department of Environmental Quality.
3) APC&EC: Arkansas Pollution Control and
Ecology Commission.
4) Closed Loop
System: A system that uses a combination of solids control equipment
incorporated in a series of steel tanks that eliminates the use of a
Pit.
5) Completion Flow-Back Fluid:
Any of a number of liquid and gaseous fluids or mixtures of fluids, chemicals
and or solids that flow from a well and consisting of Drilling Fluid, silt,
debris, water, brine, oil scum, paraffin, or other materials which have been
removed from the well bore during the initial completion of a well, but does
not include Frac Flow-Back Fluid.
6) Cuttings: Fragments of rock which are a
result of the cutting action of the drill bit on rock formations encountered in
the well, which are transported to the surface by the Drilling Fluid.
7) Discharge: The release, overflow, leakage
or seepage of any fluids covered by this Rule.
8) Drilling Fluid: Any of a number of liquid
and gaseous fluids and mixtures of fluids and solids (as solid suspensions,
mixtures and emulsions of liquids, gases, Cuttings and other solids) utilized
during brine, oil, or gas drilling operations. Drilling Fluid is generally
synonymous with drilling mud, which typically contains bentonitic clays,
chemical additives, foaming agents, lubricants, emulsifiers and weighting
materials, and which encompasses most muds used in drilling operations,
especially muds that contain significant amounts of suspended solids,
emulsified water or oil. Mud includes all types of Water-Based, Oil-Based and
synthetic-based Drilling Fluids.
9)
Director of the ADEQ: The Director of the Arkansas Department of Environmental
Quality or his or her designated representative.
10) Director of AOGC: The Director of the
Arkansas Oil and Gas Commission or his or her designated
representative.
11) Ecologically
Sensitive Waterbody (ESW): Waters that have been given the designated use of
Ecologically Sensitive Waterbody by the Arkansas Pollution Control and Ecology
Commission. This beneficial use identifies segments known to provide habitat
within the existing range of threatened, endangered or endemic species of
aquatic or semi-aquatic life forms.
12) Encountered Water: Water encountered
during brine, oil, or gas drilling operations, which is of sufficient quantity
to require disposal, and which is not Produced Water.
13) Exploration and Production Waste (E&P
Waste): Wastes associated with the exploration, development and production of
brine, oil, or gas and which are not regulated by the provisions of, and,
therefore, exempt from the Federal Resource Conservation and Recovery Act, and
may include, but are not limited to the following: salt water (produced brine
or produced water); Oil-Based Drilling Fluids; Water-Based Drilling Fluids,
Completion Flow-Back Fluid, Frac Flow-Back Fluid, Workover Flow-Back Fluid,
Produced Water; rainwater from firewalls and Pits at drilling and production
facilities; and other wastes not described above.
14) Extraordinary Resource Waters (ERW):
Waters that have been given the designated use of Extraordinary Resource
Waterbody by the Arkansas Pollution Control and Ecology Commission. This
beneficial use is a combination of the chemical, physical and biological
characteristics of a water body and its watershed which is characterized by
scenic beauty, aesthetics, scientific values, broad scope recreation potential
and intangible social values.
15)
Frac Flow-Back Fluid: Fluids that consist of fresh water and solids such as
sand or other proppant (resin or ceramic grains) or other additives that flow
from a well following hydraulic fracturing of a well, until such time as the
volume of fluid utilized for the hydraulic fracturing process in the well has
been recovered.
16) Natural and
Scenic Waterways (NSW): Waters that have been given the designated use of
Natural and Scenic Waterways by the Arkansas Pollution Control and Ecology
Commission. This beneficial use identifies segments which have been
legislatively adopted into a state or federal system.
17) Nonhazardous Oilfield Wastes (NOW):
Fluids to be used or reused in connection with activities associated with the
exploration, development, and production of brine, oil, or gas and includes,
but is not limited to, Drilling Fluids, completion fluids, surfactants, and
chemicals used to detoxify brine, oil, or gas wastes.
18) Oil-Based Drilling Fluid: Drilling Fluid
containing diesel or crude oil rather than fresh water as the main liquid phase
of the drilling mud.
19) Operator:
Any person who has the primary management and ultimate decision-making
responsibility over the operation of a facility or activity. The Operator is
responsible for ensuring compliance with all applicable regulations and
conditions.
20) Person: Natural
person, corporation, organization, municipality, government or governmental
subdivision or agency, public or private corporation, business trust, estate,
trust, individual, partnership, association, or any other legal
entity.
21) Pit: shall include:
A) Circulation Pit: A pit used during
drilling where Drilling Fluids are circulated during drilling operations. The
Circulation Pit may be part of the Mud Pit. Circulation Pits may also refer to
a series of open, above-ground tanks, usually made of steel.
B) Completion Pit: A pit used for storage of
Completion Flow-Back Fluid and Drilling Fluids or other materials which have
been cleaned out of the well bore during the initial completion of a well.
Circulation or Mud Pits may be used as a Completion Pits when drilling
operations conclude.
C) Emergency
Pit: A pit used for containing fluids at an operating well during an actual
emergency and for a temporary period of time. Use of the Emergency Pit is
necessitated due to unplanned operational issues, which may include but is not
limited to, a temporary shutdown of a disposal well or fluid injection well or
associated equipment, temporary overflow of saltwater storage tanks on a
producing lease, gas flaring, cement circulation, or a producing well loading
up with formation fluids.
D) Mud
Pit: A pit or series of pits used during drilling where fluids are mixed and
circulated during drilling operations. Mud Pits may also refer to a series of
open, above-ground tanks, usually made of steel.
E) Reserve Pit: A pit not part of the active
circulation system, used to store Drilling Fluids or to contain fluids
generated during drilling operations. Such fluids would include, but not be
limited to, Cuttings, Drilling Fluids, and Encountered Water.
F) Test Pit: A pit constructed for use during
a well test.
G) Workover Pit: A pit
used for storage of Completion Flow-Back Fluid, Workover Flow-Back Fluid and
other materials which have been cleaned out of the well bore during any
subsequent completion or re-completion.
22) Pollution: Such contamination or other
alteration of the physical, chemical, or biological properties of any waters of
the state, or such discharge of any liquid, gaseous, or solid substance in any
waters of the state as will, or is likely to, render the waters harmful,
detrimental, or injurious to public health, safety, or welfare; to domestic,
commercial, industrial, agricultural, recreational, or other legitimate
beneficial uses; or to livestock, wild animals, birds, fish, or other aquatic
life.
23) Produced Water: Water
produced from any productive or potentially productive brine, oil, or gas
producing interval in the well, which is not Completion Flow-Back Fluid, Frac
Flow-Back Fluid, Workover Flow-Back Fluid, or Encountered Water.
24) Stormwater: Rainwater runoff, snow melt
runoff, and surface runoff and drainage.
25) Water-Based Drilling Fluid: Drilling
Fluid containing fresh waters rather than diesel or crude oil as the liquid
component of the drilling mud.
26)
Waters of the State: All streams, lakes, marshes, ponds, watercourses,
waterways, wells, springs, irrigation systems, drainage systems, and all other
bodies or accumulations of water, surface and underground, natural or
artificial, public or private, which are contained within, flow through, or
border upon this state or any portion of the state.
27) Water Table: The surface between the zone
of saturation and the zone of aeration and the surface of a body of unconfined
ground water at which the pressure is equal to that of the
atmosphere.
28) Workover Flow-Back
Fluid: Any of a number of liquid and gaseous fluids and mixtures of fluids,
chemicals and or solids consisting of Drilling Fluid, silt, debris, water,
brine, oil scum, paraffin, or other materials which are removed from the well
bore during the subsequent or recompletion of a well.
d) Commencement of Construction Operations
The Operator shall notify the appropriate AOGC Regional Office,
via mail, e-mail or fax, at least forty-eight (48) hours prior to the
commencement of Pit construction operations. The Notice of Commencement (NOC)
shall be on a form agreed upon by AOGC and ADEQ and shall include at a minimum
(i) the Operator information (name, address, and emergency contact phone
number), (ii) the location of the drill pad site (latitude and longitude in
degrees, minutes, seconds, and County, Section, Range, and Township, including
the 1/4 of the 1/4 position within the Section), (iii) the approximate size of
the drill pad, (iv) the approximate distance to the nearest Waters of the
State, (v) the type of fluid system and type of Drilling Fluids to be used,
(vi) well name, (vii) nearest city/town, and (viii) the approximate date Pit
construction operations shall commence. Upon receiving the Notice of
Commencement, AOGC shall forward a copy to ADEQ, Arkansas Department of Health,
and the County Judge of the county in which the pit is located. AOGC and ADEQ
staff may conduct site inspections as deemed necessary.
f) Mud, Circulation and Reserve Pit
Construction Requirements:
1) General
Requirements:
A) Mud, Circulation and Reserve
Pits constructed within the 100 year flood plain must be in accordance with any
county or other local ordinance or requirement pertaining to the 100 year flood
plain.
B) The location of all Mud,
Circulation or Reserve Pits shall be chosen with reasonable consideration to
maximizing the distance from surface waters. Mud, Circulation or Reserve Pit
construction in streams, creeks, lakes, or any other water bodies is strictly
prohibited.
C) Any Mud, Circulation
or Reserve Pit construction in wetlands must receive appropriate prior
authorization from the U.S. Army Corps of Engineers.
D) In areas other than jurisdictional
wetlands referenced in subparagraph f) 1) C) above, where the water table is
ten (10) feet or less below the ground surface, all Mud, Circulation or Reserve
Pits shall be constructed above ground, or the Operator shall use a closed loop
system.
2) Reserve Pit
Requirements:
A) All Reserve Pits shall be
constructed with a minimum of two (2) feet of freeboard, and shall be
maintained to handle a storm event up to a 10-year, 24-hour storm event during
the operation of the Reserve Pit. Reserve Pits constructed above ground
utilizing bermed side walls, shall be constructed with a minimum of 2:1 (two
feet horizontal to one foot vertical) side slope on both the interior and
exterior walls. The top of the bermed pit walls must be a minimum of 2 feet
wide.
B) All Reserve Pits shall be
constructed with a liner using one of the following methods:
i) A synthetic liner of at least twenty (20)
mils thickness, with a four (4) inch welded seam overlap, completely covering
the Reserve Pit bottom and inside walls. Sand or sandy material must be placed
below the liner if a rocky or uneven surface is encountered. The synthetic
liner must be protected from deterioration, punctures and/or any activity which
may damage the integrity of the synthetic liner.
ii) A compacted clay liner may be applied to
the bottom and sides of the Reserve Pit to create an impervious/impermeable
barrier. Construction of the Reserve Pit and compacted clay liner shall be in
accordance with sound construction and engineering principles designed and
constructed to prevent any leakage or seepage to Waters of the State, with due
consideration given to the topography, Pit material composition, and
availability of liner material(s). The clay used to construct the liner may be
in situ or mixed with additional off-site materials, if the on-site clay is
inadequate.
iii) Other materials or
methods used for liner construction must be approved by both the Director of
the ADEQ and the Director of the AOGC prior to use.
3) Mud and Circulation Pits:
A) Closed Loop Systems may be used for Mud
and Circulation Pits, and must be maintained in a leak-free
condition.
B) Earthen Mud and
Circulation Pits shall be constructed with a minimum of two (2) feet of
freeboard, and shall be maintained to handle a storm event up to a 10-year,
24-hour storm event during the operation of the Mud or Circulation
Pit.
C) Earthen Mud and Circulation
Pit liners shall be constructed using one of the following methods:
i) A synthetic liner of at least twenty (20)
mils thickness, with a four (4) inch welded seam overlap, completely covering
the Reserve Pit bottom and inside walls. Sand or sandy material must be placed
below the liner if a rocky or uneven surface is encountered. The synthetic
liner must be protected from deterioration, punctures and/or any activity which
may damage the integrity of the synthetic liner.
ii) Bentonite drilling mud from fresh
Water-Based Drilling Fluids may be used on the bottom and sides of the earthen
Mud or Circulation Pit to create an impervious/impermeable barrier. Application
of the Mud or Circulation Pit bentonite drilling mud liner shall be in
accordance with sound construction and standard industry practices designed and
constructed to prevent any Discharge.
iii) A concrete liner may be applied to the
bottom and sides of the earthen Mud or Circulation Pit to create an
impervious/impermeable barrier. Construction of the Mud or Circulation Pit
concrete liner shall be in accordance with sound construction and standard
industry practices designed and constructed to prevent any Discharge.
D) Oil-Based Drilling Fluids shall
not be placed in an earthen Mud or Circulation Pit unless the Pit is lined with
a synthetic or concrete liner as prescribed in subparagraph f) 3) C) i) or iii)
above.
E) If Oil-Based Drilling
Fluids are to be used, and the location of the Mud or Circulation Pit is within
100 feet of a pond, lake, stream, ERW, ESW or NSW, the Operator is required to
use a Closed Loop System.
g) Operating Requirements For Mud,
Circulation or Reserve Pits:
1) No waste oil,
hydraulic fluids, transmission fluids, trash or any other miscellaneous rig
waste may be placed, stored or disposed into a Mud, Circulation, or Reserve
Pit.
2) Produced Water, and Frac
Flow-Back Fluid may not be placed, stored or disposed in a Mud, Circulation, or
Reserve Pit, except that as part of a Frac Flow-Back Fluid recycling program,
Frac Flow-Back Fluids, and upon approval of both AOGC and ADEQ Directors,
Produced Water, may be temporarily placed or stored in a Reserve Pit, for a
period not to exceed ninety (90) days per pit use for this purpose if:
A) The Reserve Pit is constructed with a clay
liner as specified in subparagraph f) 2) B) ii) above and a synthetic liner of
at least forty (40) mils thickness, or two (2) twenty (20) mils thickness
synthetic liners, in addition to all other applicable Reserve Pit construction
requirements as specified in subparagraph f) 2) above, and have a means to
monitor between the synthetic liners (if two liners are utilized) and below the
bottom of the lower most synthetic liner; and
B) The Operator requests approval from ADEQ
in writing prior to the placement or storage of the Frac Flow-Back Fluid or
approved Produced Water, in a Reserve Pit. Such request shall include the AOGC
Well Permit Number, well names(s), description of the water to be stored,
anticipated dates of use, volume of water to be stored or placed, detailed
information on any proposed pipelines for the transfer Frac Flow-Back Fluids
including a map showing proposed pipeline location for; and
C) No Frac Flow-Back Fluids or other fluids
mixed with Frac Flow-Back Fluids temporally stored or placed in a Reserve Pit
may be sent to any commercial land applications disposal facility or land
applied onsite.
3)
Water-Based Drilling Fluid, Stormwater, water from Waters of the State, or
Encountered Water may be placed or stored in an earthen Mud, Circulation or
Reserve Pit.
4) Mud, Circulation
and Reserve Pits must be maintained in such a manner as to prohibit any
Discharges. The Operator is required to maintain adequate storage capacity at
all times.
5) Mud, Circulation and
Reserve Pit levees or walls shall be protected and maintained at all times to
prevent deterioration or discharge. In addition, Pit liners shall also be
maintained and protected from deterioration or puncture causing discharge of
fluids until such time that the Pit is emptied and closed.
6) Mud, Circulation and Reserve Pits shall
contain only Drilling Fluids generated during the drilling of the well or wells
at the drilling pad where the Pit is constructed, except that as part of a Frac
Flow-Back Fluid recycling program a Reserve Pit, permitted in accordance with
subparagraph g) 2) above, may temporarily contain Frac Flow-Back Fluids and
upon approval by both AOGC and ADEQ Directors, Produced Water, which may be
transferred to another drill pad Reserve Pit permitted in accordance with
subparagraph g) 2) above. The transfer of Frac Flow-Back Fluids and approved
Produced Water, via tank truck, shall be in accordance with General Rule E-3.
If the transfer of Frac Flow-Back Fluids and approved Produced Water, is via
pipeline, such pipeline shall be constructed and maintained in a leak-free
condition and protected from deterioration, punctures and/or any activity which
may damage the integrity of the pipeline. If the proposed pipeline will result
in a stream crossing, a short term activity authorization shall be received
from the ADEQ prior to construction. Any discharge from the pipeline shall be
reported immediately to ADEQ.
7) In
the event of an emergency and with prior approval from either the Director of
ADEQ or the AOGC, the Reserve Pit may be used for temporary additional storage
of Water-Based Drilling Fluids from another drilling pad location. In the event
of an emergency, any request for approval must be submitted to both ADEQ and
AOGC for review. ADEQ or AOGC will provide notice to each other at the time of
the approval of any request made pursuant to this paragraph.
8) Except as specified in subparagraph i) 1),
or in an emergency and with prior approval from the Director of the ADEQ
hauling or transporting Drilling Fluids from a Pit to an off-site location, not
located on a drilling pad, for additional storage is prohibited.
9) Oil-Based Drilling Fluids shall be
segregated from Water-Based Drilling Fluids and other Drilling
Fluids.
h) Fluid
Disposal and Earthen Pit Closure Requirements for Water-Based Drilling Fluid
and Encountered Water.
1) Water-Based Drilling
Fluid, Stormwater, water from Waters of the State, or Encountered Water stored
in the Pits shall be removed to the maximum extent practical using pumps or
similar equipment at the time of Pit closure, and shall be disposed of in one
of the following manners:
A) Land applied in
accordance with an active ADEQ land application permit.
B) Disposed of fluid into approved NPDES or
state permitted facility.
C)
Injected via Class II wells permitted by AOGC.
D) Pumping the Water-Based Drilling Fluids
back down the well bore of the well in accordance with AOGC
requirements.
E) Water-Based
Drilling Fluids exhibiting high viscosity to high solids concentration may be
solidified or stabilized by combining with available native soils and buried in
situ. The Operator is responsible for ensuring the native soils are properly
mixed to prevent any discharge.
F)
Transported by truck or by pipeline to a Reserve Pit, which is part of an
approved Frac Flow-back Fluid recycle program.
G) By any other method as approved by ADEQ
and AOGC.
2) The
Operator shall take all reasonable measures to ensure that Drilling Fluid and
Encountered Water that is removed from the well-site, are properly transported
to and disposed of or recycled or reclaimed at an AOGC or ADEQ permitted site
or facility, or a permitted site or facility outside of Arkansas.
3) Any synthetic liner used shall be removed
to the fullest extent practicable and properly disposed or recycled.
4) The closed Pit shall be filled with native
materials and covered with topsoil at depths consistent with adjoining onsite
areas, with the contour mounded or sloped to discourage erosion and restored as
close to the original contours as is practicable. Topsoil and native materials
removed during Pit construction may be preserved and used during
closure.
5) The oil & grease
content of the material to be buried in situ shall be less than 3% by dry
weight.
6) The pit and applicable
portion of the drill pad not utilized for production purposes, shall be
returned to grade, reclaimed and seeded within a reasonable amount of time not
to exceed one hundred eighty days (180) days after the drilling or workover rig
is removed from the site, or in the case of a multiple well drill pad, within
180 days after the drilling or workover rig utilized for the last well to be
drilled from the drill pad is removed, during which period the reserve pit
shall be maintained in accordance with the provisions of this rule. An
extension of the time to close the pit may be granted upon approval of both
AOGC and ADEQ. Vegetative coverage of 75%, or equivalent to the surrounding
landscape, whichever is less, shall be obtained within six (6) months of Pit
closure. Until vegetation is established, the Operator is responsible for
maintaining a stormwater erosion and sediment control plan.
7) The Operator shall submit the Notice of
Pit closure to AOGC signed by the Operator within 30 days after Pit closure has
been completed. AOGC shall forward a copy to ADEQ.
i) Fluid Disposal and Earthen Pit Closure
Requirements for Oil-Based Drilling Fluids.
1) Oil-Based Drilling Fluids shall be removed
from the Pit and hauled to a permitted Class 1 (as defined by APC&EC
Regulation No. 22) landfill for disposal or be transferred to above ground
tanks for re-use at another well location, or other disposal methods or uses of
Oil-Based Drilling Fluids as approved by the ADEQ. The Operator shall inform
the AOGC of the location of the disposal or transfer of the Oil-Based Drilling
Fluid. AOGC shall forward a copy to ADEQ.
2) If an Oil-Based Drilling Fluid other than
diesel is used as the base, additional analytical or disposal requirements may
be required, which shall require prior notification and approval by
ADEQ.
3) Any synthetic liner used
shall be removed to the fullest extent practicable and properly disposed or
recycled.
4) The closed Pit shall
be filled with native materials and covered with topsoil at depths consistent
with adjoining onsite areas, with the contour mounded or sloped to discourage
erosion and restored as close to the original contours as is practicable.
Topsoil and native materials removed during Pit construction may be preserved
and used during closure.
5) The
area shall be returned to grade, reclaimed and seeded within a reasonable
amount of time not to exceed one hundred eighty days (180) days after the
drilling rig is removed from the site. Vegetative coverage of 75%, or
equivalent to the surrounding landscape, whichever is less, shall be obtained
within six (6) months of closure. Until vegetation is established, the Operator
is responsible for maintaining a stormwater erosion and sediment control
plan.
6) The Operator shall submit
the Notice of Pit closure to AOGC signed by the Operator within 30 days after
Pit closure has been completed. AOGC shall forward a copy to ADEQ.