Historic Preservation, Advisory Council August 25, 2015 – Federal Register Recent Federal Regulation Documents

We propose to adopt a new airworthiness directive (AD) for all M7 Aerospace LLC Models SA26-AT, SA226-T, SA226-AT, SA226-T(B), SA226- TC, SA227-AT, SA227-TT, SA227-AC (C-26A), SA227-BC (C-26A), SA227-CC, and SA227-DC (C-26B) airplanes. This proposed AD was prompted by information that the airplane flight manual (AFM) does not provide adequate guidance in the handling of engine failures, which may lead to reliance on the negative torque system (NTS) for reducing drag. This condition could lead the pilot to not fully feather the propeller with consequent loss of control. This proposed AD would require inserting updates into the airplane flight manual (AFM) and/or the pilot operating handbook (POH) that will clearly establish that the NTS is not designed to automatically feather the propeller but only to provide drag protection. We are proposing this AD to correct the unsafe condition on these products.

This notice sets forth the reasons for denying a petition submitted to NHTSA, 49 U.S.C. 30162, 49 CFR part 552, requesting that the agency open ``an investigation into low-speed surging in different models of Toyota automobiles in which the car starts accelerating and the engine RPM increases even when the accelerator pedal is not depressed.''

We propose to adopt a new airworthiness directive (AD) for all The Boeing Company Model 777-200, -200LR, -300, and -300ER series airplanes. This proposed AD was prompted by reports of fractured forward attach fittings of the inboard flap outboard aft flap track. The fractured fittings were determined to be the result of corrosion pits forming on the inside diameter of the fittings. This proposed AD would require an inspection for the affected part number and serial number of the main flap; various additional repetitive inspections of the fitting, if necessary; and replacement of the fitting or nested bushing installation, if necessary, which would terminate the inspections. This proposed AD would also provide for optional terminating action for the repetitive inspections. We are proposing this AD to detect and correct fracture of the fitting, which could result in the loss of the inboard aft flap and could lead to a punctured fuselage, causing injury to the flightcrew and passengers, and damage to the airplane.

We are superseding Airworthiness Directive (AD) 2007-04-13 for certain SOCATA Model TBM 700 airplaness (type certificate previously held by EADS SOCATA). This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracks found on the main landing gear cylinders. We are issuing this AD to require actions to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for all Airbus Model A300 B4-603, B4-605R, B4-620, B4-622, B4-622R airplanes; all Airbus Model A300 C4-605R Variant F airplanes; and certain Airbus Model A300 F4-605R airplanes. This AD was prompted by the manufacturer's review of all repairs accomplished using the structural repair manual. This review was done using revised fatigue and damage tolerance calculations. This AD requires an inspection of the surrounding panels of the left and right forward passenger doors, and corrective actions if necessary. We are issuing this AD to detect and correct previous incomplete or inadequate repairs to the surrounding panels of the left and right forward passenger doors and the fail-safe ring, which could negatively affect the structural integrity of the airplane.

We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by a report of several events where pilots experienced difficulty in lateral control of the airplane after doing a climb through heavy rain conditions and a determination that the cause was water ingress in the aileron control pulley assembly. This AD requires, for certain airplanes, inspecting for correct clearance and rework if necessary, and, for certain other airplanes, installing a cover for the aileron pulley assembly. We are issuing this AD to prevent water ingress in the aileron control pulley assembly, which could freeze in cold conditions and result in reduced control of the airplane.