Federal Aviation Administration November 2017 – Federal Register Recent Federal Regulation Documents

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The purpose of this research is to conduct a nation-wide survey to update the scientific evidence of the relationship between aircraft noise exposure and its effects on communities around airports.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to reinstate a previously approved information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on August 31, 2017. In that the notice the collection was mistitled: ``Laser Operations in the Navigable Airspace (Advisory Circular (AC), Outdoor Laser Operations.'' We received no comments. In order for the FAA to ensure safety it proposes to collect information from potential outdoor laser operators. The FAA will review the proposed laser activity against air traffic operations and verify that the laser operation will not interfere with air traffic operations.

We propose to adopt a new airworthiness directive (AD) for certain Airbus Model A318, A319, A320, and A321 series airplanes; all Model A330-200 Freighter, -200, and -300 series airplanes; and all Model A340-200, -300, -500, and -600 series airplanes. This proposed AD was prompted by reports of false traffic collision avoidance system (TCAS) resolution advisories. This proposed AD would require modifying the software in the TCAS computer processor or replacing the TCAS computer with a new TCAS computer. We are proposing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for Sikorsky Aircraft Corporation (Sikorsky) Model S-76A, S-76B, S-76C, and S-76D helicopters. This AD requires inspecting the main rotor (M/R) servo pushrod (pushrod) assembly and applying slippage marks. This AD was prompted by an accident of a Sikorsky Model S-76C helicopter caused by a failed pushrod assembly. The actions of this AD are intended to prevent an unsafe condition on these products.

We are removing Airworthiness Directive (AD) 2017-01-06, which applied to certain Airbus Model A319-115, A319-132, A320-214, A320-232, A321-211, A321-213, and A321-231 airplanes. AD 2017-01-06 required inspection and replacement of certain tie rod assemblies installed on the hinged fairing assembly of the main landing gear (MLG). We issued AD 2017-01-06 to detect and correct the absence of cadmium plating on the rod end threads of the tie rod assemblies. Since we issued AD 2017- 01-06, we have determined that although cadmium plating might be absent, the rod end threads of the tie rod assemblies can withstand the expected environmental conditions, therefore the unsafe condition, as initially determined, does not exist.

We are adopting a new airworthiness directive (AD) for certain Airbus Model A319 series airplanes; Model A320-211, -212, -214, -231, - 232, and -233 airplanes; and Model A321-111, -112, -131, -211, -212, - 213, -231, and -232 airplanes. This AD was prompted by a report of cracks on frame forks and outer skin on the forward and aft cargo compartment doors. This AD requires repetitive inspections of the frame forks, and corrective actions if necessary. This AD also includes optional modifications that constitute terminating action. We are issuing this AD to address the unsafe condition on these products.

This action proposes to establish Class E airspace extending upward from 700 feet above the surface, at Spanish Fork Airport Springville-Woodhouse Field, Spanish Fork, UT, to accommodate new area navigation (RNAV) procedures at the airport. This action would ensure the safety and management of Instrument Flight Rules (IFR) operations within the National Airspace System.

This action amends Class D airspace, Class E surface area airspace, and Class E airspace upward from 700 feet above the surface at Pueblo Memorial Airport, Pueblo, CO. Also, the part-time Notice to Airmen (NOTAM) information is removed from Class E airspace designated as an extension, and the geographic coordinates for Pueblo Memorial Airport in the associated Class D and E airspace areas are amended to match the FAA's aeronautical database. A biennial review found these changes are necessary to accommodate airspace redesign for the safety and management of Instrument Flight Rules (IFR) operations within the National Airspace System. An editorial change also is made to the Class D airspace and Class E surface area airspace legal descriptions replacing ``Airport/Facility Directory'' with the term ``Chart Supplement.''

This action amends Class E airspace at Alexander City, AL, due to the decommissioning of the Alexander City non-directional radio beacon (NDB), which requires airspace reconfiguration at Thomas C Russell Field Airport. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations at the airport. This action also updates the geographic coordinates of the airport.

We are revising an earlier proposal for certain The Boeing Company Model 767-300 and -300F series airplanes. This action revises the notice of proposed rulemaking (NPRM) by adding new high frequency eddy current (HFEC) inspections for cracking of an expanded area of the lower outboard wing skin for certain airplanes. We are proposing this airworthiness directive (AD) to address the unsafe condition on these products. Since these actions would impose an additional burden over those in the NPRM, we are reopening the comment period to allow the public the chance to comment on these changes.

This notice of proposed rulemaking (NPRM) would allow pilots who obtained pilot in command (PIC) experience prior to July 31, 2013, in certain air carrier operations, to count that time towards the 1,000 hours of air carrier experience required to serve as a PIC in air carrier operations today. This would correct an inadvertent omission in the Pilot Certification and Qualification Requirements for Air Carrier Operations final rule that established the air carrier experience requirement. It would also broaden the existing 500-hour credit military pilots of fixed-wing airplanes can use towards the 1,000 hours of air carrier experience by permitting pilots of select powered-lift aircraft operations to receive credit. This NPRM would also allow credit for select military time in a powered-lift aircraft flown in horizontal flight towards the 250 hours of airplane time as PIC, or second in command (SIC) performing the duties of PIC, required for an airline transport pilot (ATP) certificate.

We are adopting a new airworthiness directive (AD) for certain ATRGIE Avions de Transport R[eacute]gional Model ATR42-500 airplanes and Model ATR72-212A airplanes. This AD requires an inspection for routing attachments of electrical harness bundles and for wire damage, and corrective actions if necessary. This AD was prompted by reports of electrical harness bundle chafing with a window blinding panel in the fuselage due to missing routing attachments. We are issuing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-400, 747-400F, and 747-8F series airplanes. This AD was prompted by reports of failure of the fastener assemblies on the crew access ladder handrails. This AD requires replacing the fastener assemblies. We are issuing this AD to address the unsafe condition on these products.

We propose to adopt a new airworthiness directive (AD) for various aircraft equipped with a BRP-Rotax GmbH & Co. KG (formerly BRP- Powertrain GmbH & Co. KG; Bombardier-Rotax GmbH & Co. KG; Bombardier- Rotax GmbH) 912 A series engine. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as defective valve push-rod assemblies manufactured from June 8, 2016, through October 2, 2017. We are issuing this proposed AD to require actions to address the unsafe condition on these products.

The FAA is issuing this notice to advise the public that the FAA has prepared and approved (September 6, 2017) an Amended FONSI/ROD based on the Final SEA for the DTL Runway 13/31 Shift/Extension and Associated Improvements Project. The Final SEA was prepared in accordance with the National Environmental Policy Act (NEPA) of 1969, as amended, FAA Orders 1050.1F, ``Environmental Impacts: Policies and Procedures'' and 5050.4B, ``NEPA Implementing Instructions for Airport Actions''.

This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This rule amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide for the safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

This rule amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide for the safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

This action proposes to amend Class E airspace extending upward from 700 feet above the surface in Selinsgrove, PA. A new area navigation (RNAV) global positioning system (GPS) standard instrument approach procedure has been developed at Penn Valley Airport, requiring airspace reconfiguration. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations at the airport. This action also would update the geographic coordinates of the airport.

This action establishes Class E airspace extending upward from 700 feet above the surface at Boothville Heliport, Boothville, LA. Controlled airspace is necessary to accommodate new special instrument approach procedures developed at Boothville Heliport, for the safety and management of instrument flight rules (IFR) operations at the heliport.

We propose to adopt a new airworthiness directive (AD) for all The Boeing Company Model 707 airplanes, and Model 720 and 720B series airplanes. This proposed AD was prompted by fuel system reviews conducted by the manufacturer. This proposed AD would require revising the maintenance or inspection program to include new airworthiness limitations. We are proposing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-2A12 (CL-601 Variant) and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604 Variants) airplanes. This AD was prompted by a determination that the bushing holes on the engine mount rib might not conform to the engineering drawings and that certain inspections of the engine mount rib must be included in the airworthiness limitations section (ALS) of the Instructions for Continued Airworthiness (ICA). This AD requires revising the maintenance or inspection program to incorporate certain airworthiness limitation items (ALIs). We are issuing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 757-200, -200PF, and -200CB series airplanes. This AD was prompted by reports of slats disbonding on airplanes on which the terminating actions of AD 2005-07-08 had been performed. We have also received reports of slats disbonding on airplanes outside of the applicability of AD 90-23-06, AD 91-22-51, and AD 2005-07-08, which also addressed slat disbonding. This AD requires determining the type of trailing edge slat wedges of the leading edge slats, repetitive inspections for disbonding on certain trailing edge slat wedges, and corrective actions if necessary. This AD also provides an optional terminating action for the repetitive inspections. We are issuing this AD to address the unsafe condition on these products.

We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 and 787-9 airplanes. This proposed AD was prompted by reports of failures of the lip heater assemblies of the inlet ice protection system of the cabin air compressor (CAC) due to chafing. This proposed AD would require changing the airplane electrical connectors and the routes of certain wire bundles, and installing new or modified left and right CAC inlet duct assemblies. We are proposing this AD to address the unsafe condition on these products.

The FAA announces the availability of and requests comments on proposed airworthiness criteria for the Unmanned Aircraft System, FlightScan Corporation, Camcopter S-100. This document provides proposed policy for airworthiness criteria to address the designation of applicable regulations and other criteria for special classes of aircraft. In addition to the proposed airworthiness criteria presented in this document, we are also referencing operational considerations that have been used to support the development of the airworthiness criteria. We consider these proposed criteria to be interim because we anticipate the evolution of new operational criteria will necessitate additional airworthiness criteria in order to allow for the operation of the Camcopter S-100 in the National Airspace System. When those additional operational criteria are further established, we will again provide public notice of proposed policy with additional airworthiness criteria along with changes incorporated to these criteria based on the public comments received.