Federal Aviation Administration September 2016 – Federal Register Recent Federal Regulation Documents

Airworthiness Directives; General Electric Company Turbofan Engines
Document Number: 2016-23740
Type: Rule
Date: 2016-09-30
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all General Electric Company (GE) GE90-76B, GE90-77B, GE90-85B, GE90-90B, and GE90-94B turbofan engines with high-pressure compressor (HPC) stage 8-10 spool, part numbers (P/Ns) 1694M80G04, 1844M90G01, or 1844M90G02, installed. This AD was prompted by reports of cracks found on the seal teeth of the HPC stage 8-10 spool. This AD requires eddy current inspections (ECIs) or fluorescent penetrant inspections (FPIs) of the HPC stage 8-10 spool seal teeth and removing from service those parts that fail inspection. We are issuing this AD to prevent failure of the HPC stage 8-10 spool, uncontained rotor release, damage to the engine, and damage to the airplane.
Special Conditions: Embraer S.A., Model ERJ 190-300 Series Airplanes; Electronic Flight Control System: Control Surface Position Awareness, Multiple Modes of Operation
Document Number: 2016-23665
Type: Rule
Date: 2016-09-30
Agency: Federal Aviation Administration, Department of Transportation
These special conditions are issued for the Embraer S.A. Model ERJ 190-300 series airplanes. These airplanes will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. This design feature is a fly-by-wire electronic flight control system (EFCS) and no direct coupling from the flight deck controller to the control surface. As a result, the pilot is not aware of the actual control surface position. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Special Conditions: DAHER-SOCATA, Model TBM 700; Inflatable Four-Point Restraint Safety Belt With an Integrated Airbag Device
Document Number: 2016-23564
Type: Rule
Date: 2016-09-30
Agency: Federal Aviation Administration, Department of Transportation
These special conditions are issued for the installation of an inflatable four-point restraint safety belt with an integrated airbag device at the pilot and copilot seats on the DAHER-SOCATA, Model TBM 700 airplane. These airplanes, as modified by the installation of these inflatable safety belts, will have novel and unusual design features associated with the upper-torso restraint portions of the four-point safety belts, which contain an integrated airbag device. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Modification of Class E Airspace; Napa, CA
Document Number: 2016-23423
Type: Rule
Date: 2016-09-30
Agency: Federal Aviation Administration, Department of Transportation
This action modifies the Class E airspace extending upward from 700 feet above the surface at Napa County Airport, Napa, CA, by removing an irregular shaped area located approximately 20 miles southwest of Napa County Airport. This airspace area is discontinuous from the airspace surrounding Napa County Airport and is not essential to instrument flight rules (IFR) operations at the airport. This action also updates the airport's geographic coordinates, and is necessary for the safety and management of instrument flight rules (IFR) operations at the airport, with the minimum amount of airspace restriction.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
Document Number: 2016-23414
Type: Rule
Date: 2016-09-30
Agency: Federal Aviation Administration, Department of Transportation
This rule amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide for the safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
Document Number: 2016-23411
Type: Rule
Date: 2016-09-30
Agency: Federal Aviation Administration, Department of Transportation
This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
Document Number: 2016-23410
Type: Rule
Date: 2016-09-30
Agency: Federal Aviation Administration, Department of Transportation
This rule amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide for the safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
Document Number: 2016-23406
Type: Rule
Date: 2016-09-30
Agency: Federal Aviation Administration, Department of Transportation
This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Airworthiness Directives; Bell Helicopter Textron Canada Limited (Bell) Helicopters
Document Number: 2016-23345
Type: Rule
Date: 2016-09-30
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for Bell Model 427 and Model 429 helicopters. This AD requires replacing certain engine and transmission oil check valves. This AD also prohibits installing the affected check valves on any helicopter. This AD is prompted by a report of several cracked or leaking check valves. These actions are intended to detect and prevent a cracked or leaking check valve which could result in loss of lubrication to the engine or transmission, failure of the engine or transmission, and subsequent loss of control of the helicopter.
Airworthiness Directives; Honeywell International Inc. Turboprop and Turboshaft Engines
Document Number: 2016-23263
Type: Rule
Date: 2016-09-30
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Honeywell International Inc. (Honeywell) TPE331 model turboprop engines and TSE331-3U model turboshaft engines. This AD was prompted by the discovery of cracks in a 2nd stage compressor impeller during a routine shop visit. This AD requires removal of the 2nd stage compressor impeller. We are issuing this AD to prevent failure of the compressor impeller, uncontained part release, damage to the engine, and damage to the airplane.
Notice of Submission Deadline for Schedule Information for Chicago O'Hare International Airport, John F. Kennedy International Airport, Los Angeles International Airport, Newark Liberty International Airport, and San Francisco International Airport for the Summer 2017 Scheduling Season
Document Number: 2016-23563
Type: Notice
Date: 2016-09-29
Agency: Federal Aviation Administration, Department of Transportation
Under this notice, the FAA announces the submission deadline of October 6, 2016, for summer 2017 flight schedules at Chicago O'Hare International Airport (ORD), John F. Kennedy International Airport (JFK), Los Angeles International Airport (LAX), Newark Liberty International Airport (EWR), and San Francisco International Airport (SFO), in accordance with the International Air Transport Association (IATA) Worldwide Slot Guidelines (WSG). The deadline coincides with the schedule submission deadline for the IATA Slot Conference for the summer 2017 scheduling season.
Airworthiness Directives; Gulfstream Aerospace Corporation Airplanes
Document Number: 2016-23091
Type: Rule
Date: 2016-09-29
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all Gulfstream Aerospace Corporation Model G-1159, G-1159A, G-1159B, and G- IV airplanes. This AD requires revision of the maintenance or inspection program to establish the life limit of all elevator assemblies and skins on affected airplanes. This AD was prompted by the need to establish life limits for certain elevator assemblies and skins. We are issuing this AD to prevent failure of the elevator assembly and consequent loss of control of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-23088
Type: Proposed Rule
Date: 2016-09-29
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This proposed AD was prompted by reports of the Krueger flap bullnose departing an airplane during taxi, which caused damage to the wing structure and thrust reverser. This proposed AD would require a one-time detailed visual inspection for discrepancies in the Krueger flap bullnose attachment hardware, and related investigative and corrective actions if necessary. We are proposing this AD to detect and correct missing Krueger flap bullnose hardware. Such missing hardware could result in the Krueger flap bullnose departing the airplane during flight, which could damage empennage structure and lead to the inability to maintain continued safe flight and landing.
Airworthiness Directives; Airbus Defense and Space S.A. (Formerly Known as Construcciones Aeronauticas, S.A.) Airplanes
Document Number: 2016-23085
Type: Proposed Rule
Date: 2016-09-29
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for all Airbus Defense and Space S.A. (formerly known as Construcciones Aeronauticas, S.A.) Model CN-235, CN 235-100, CN 235-200, and CN 235- 300 airplanes. This proposed AD was prompted by reports of cracks in certain areas of the rear fuselage. This proposed AD would require repetitive borescope and detailed visual inspections of the rear fuselage lateral beam and its external area and repair if necessary. We are proposing this AD to detect and correct cracks in the rear fuselage lateral beam and its external area; such cracking could lead to failure of the affected components, and result in reduced structural integrity of the fuselage.
Incorporation by Reference of ICAO Annex 2; Removal of Outdated North Atlantic Minimum Navigation Performance Specifications
Document Number: 2016-22798
Type: Proposed Rule
Date: 2016-09-29
Agency: Federal Aviation Administration, Department of Transportation
This rulemaking proposes to harmonize the FAA's regulations regarding the North Atlantic (NAT) Minimum Navigation Performance Specifications (MNPS) with those of the International Civil Aviation Organization (ICAO). ICAO's NAT Region is transitioning from the decades-old MNPS navigation specification to a more modern, Performance-Based Navigation (PBN) specification. This proposed rule would also correct and update the incorporation by reference of ICAO Annex 2 in the FAA's regulations.
Notice of Intent To Rule on Disposal of Aeronautical Property at Everett-Stewart Regional Airport, Union City, TN (UCY)
Document Number: 2016-23425
Type: Notice
Date: 2016-09-28
Agency: Federal Aviation Administration, Department of Transportation
The Federal Aviation Administration is requesting public comment on a request by Obion County, to release three parcels of land (8.48 acres) at Everett-Stewart Regional Airport from federal obligations.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Flight Operational Quality Assurance (FOQA) Program
Document Number: 2016-23419
Type: Notice
Date: 2016-09-28
Agency: Federal Aviation Administration, Department of Transportation
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. Flight Operational Quality Assurance (FOQA) is a program for the routine collection and analysis of digital flight data from airline operations, including but not limited to digital flight data currently collected pursuant to existing regulatory provisions. The FAA requires certificate holders who voluntarily establish approved FOQA programs to periodically provide aggregate trend analysis information from such programs to the FAA.
Notice of Land Use Change and Release of Grant Assurance Restrictions at the Oceano County Airport, Oceano, San Luis Obispo County, California
Document Number: 2016-23417
Type: Notice
Date: 2016-09-28
Agency: Federal Aviation Administration, Department of Transportation
The Federal Aviation Administration (FAA) proposes to rule and invites public comment on the application for a land-use change for approximately .834 acres of airport property at Oceano County Airport, Oceano, California. The land use change will permit the release of the aeronautical use provision of the Grant Assurances that require it to serve an airport purpose since the land is not needed for aeronautical uses. The released land will be used for storm drainage improvements intended to enhance the existing drainage system in the southerly portion of the Oceano community adjacent to the east portion of the Oceano County Airport. The project will also reduce existing runoff on airport property as well as alleviate an existing drainage problem on Highway 1 at 13th Street. The fair market value will be paid for the land and thereby serve the interest of civil aviation.
Hazardous Materials: Emergency Restriction/Prohibition Order
Document Number: 2016-23332
Type: Notice
Date: 2016-09-28
Agency: Federal Aviation Administration, Department of Transportation
This notice provides Emergency Restriction/Prohibition Order No. FAA-2016-9156, issued September 16, 2016 to Braille Battery, Inc. The Emergency Order prohibits Braille Battery from offering for transportation and transporting, any lithium ion battery that is not in compliance with the HMR or the International Civil Aviation Organization (ICAO) Technical Instructions as permitted in the HMR; requires Braille Battery to maintain and make publicly available the complete test record issued by the testing facility for each lithium ion battery manufactured by Braille Battery proven to meet the criteria in part III, sub-section 38.3 of the UN Manual of Tests and Criteria; requires Braille Battery to notify third party vendors that may offer for transportation, or transport, via air any lithium ion battery manufactured by Braille Battery that the third party vendor should not offer for transportation, nor transport, via air a Braille Battery lithium ion battery until Braille Battery confirms that the lithium ion battery is of a design type proven to meet the criteria in part III, sub-section 38.3 of the UN Manual of Tests and Criteria; prohibits Braille from using any ``hazmat employee'' that has not received training in accordance with the HMR; and prohibits Braille Battery from offering for transportation, or transporting, by air any hazardous materials requiring a DOT specification or UN standard packaging unless Braille Battery follows the applicable packing and closure instructions.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-23082
Type: Proposed Rule
Date: 2016-09-28
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for all The Boeing Company Model 767-200, -300, and -400ER series airplanes. This proposed AD was prompted an evaluation by the design approval holder (DAH) indicating that the fuselage skin lap splices are subject to widespread fatigue damage (WFD). This proposed AD would require repetitive inspections to detect any crack in the fuselage skin at the skin lap splices. We are proposing this AD to detect and correct cracks at the fuselage skin lap splice, which can rapidly link up, possibly resulting in rapid decompression and loss of structural integrity of the airplane.
Airworthiness Directives; Saab AB, Saab Aeronautics (Formerly Known as Saab AB, Saab Aerosystems) Airplanes
Document Number: 2016-23081
Type: Rule
Date: 2016-09-28
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all Saab AB, Saab Aeronautics Model SAAB 2000 airplanes. This AD requires an inspection to identify the type of fasteners installed on the upper longerons and upper fittings of the engine mounting structure (EMS), an inspection for discrepancies of certain fasteners, and corrective action if necessary. This AD was prompted by the discovery of blind fasteners installed in EMS upper fittings that do not meet the type design. We are issuing this AD to detect and correct discrepancies of blind fasteners that could cause crack development and vibration in the engine mount structure, which could lead to failure of the affected engine-mount-to-airplane structural connection and resultant detachment of an engine from the airplane when both sides of a nacelle are affected.
Airworthiness Directives; REIMS AVIATION S.A. Airplanes
Document Number: 2016-22830
Type: Rule
Date: 2016-09-28
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain REIMS AVIATION S.A. Model F406 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracks found in the horizontal stabilizer rear attach structure and the vertical fin rear spar attach structure. We are issuing this AD to prevent structural failure of the horizontal stabilizer and/or the vertical fin rear spar attach structure, which could result in damage to the airplane and loss of control.
Airworthiness Directives; Bombardier, Inc. Airplanes
Document Number: 2016-22705
Type: Rule
Date: 2016-09-28
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-400 series airplanes. This AD was prompted by a malfunctioning No. 2 engine intake heater with corrosion on the thermostats and the fuselage skin where the thermostats made contact with the aircraft fuselage skin. This AD requires a general visual inspection for corrosion of the thermostats' mounting surfaces and fuselage skin surface, corrective actions if necessary, and relocating the existing thermostats. We are issuing this AD to prevent corrosion within the thermostats that might cause the switch mechanism to seize in the open position and prevent the activation of the associated engine air intake heater. An inactive engine air intake heater could lead to an engine failure.
Airworthiness Directives; Airbus Airplanes
Document Number: 2016-21150
Type: Rule
Date: 2016-09-28
Agency: Federal Aviation Administration, Department of Transportation
We are superseding Airworthiness Directive (AD) 2009-15-17 for certain Airbus Model A330-200 and -300 series airplanes; and Model A340-200 and -300 series airplanes. AD 2009-15-17 required an inspection for damage to the protective treatments or any corrosion of all main landing gear (MLG) bogie beams, and application of protective treatments if no damage or corrosion was found. If any damage or corrosion was found, corrective action followed by the application of protective treatments was required. This new AD continues to require inspections for damage to the protective treatments or any corrosion of all MLG bogie beams, application of protective treatments, and corrective action if necessary. This new AD also requires modification of the MLG bogie beams, which terminates the repetitive inspections for any modified bogie beam. This new AD allows optional methods of compliance for certain actions, and adds Airbus Model A330-200 Freighter series airplanes to the applicability. This new AD revises the compliance times and adds a one-time inspection for airplanes that were inspected too early. This AD was prompted by reports of thin paint coats and paint degradation on enhanced main landing gear (MLG) bogie beams, as well as reports that some airplanes have been inspected too early and not re-inspected as needed. We are issuing this AD to detect and correct damage or corrosion of the MLG bogie beams, which could cause a runway excursion event, bogie beam detachment from the airplane, or MLG collapse, and could result in damage to the airplane and injury to the occupants.
Modification of Colored Federal Airway B-1; Alaska
Document Number: 2016-23116
Type: Rule
Date: 2016-09-27
Agency: Federal Aviation Administration, Department of Transportation
This action renames Blue Federal airway B-1 in Alaska to B-12. This is necessary due to an automation issue that conflicts with an identically named airway in Taiwan. No air traffic services with be affected by this action.
Amendment of Class E Airspace; Tekamah, NE
Document Number: 2016-23114
Type: Rule
Date: 2016-09-27
Agency: Federal Aviation Administration, Department of Transportation
This action modifies Class E airspace extending upward from 700 feet above the surface at Tekamah Municipal Airport, Tekamah, NE. Controlled airspace is necessary to accommodate standard instrument approach procedures (SIAP) at Tekamah Municipal Airport for the safety and management of Instrument Flight Rules (IFR) operations at airport.
Proposed Amendment of Class E Airspace for the Following Ohio Towns; Findlay, OH; Ashland, OH; Celina, OH; Circleville, OH; Columbus, OH; Defiance, OH; Hamilton, OH; Lima, OH; and London, OH
Document Number: 2016-23113
Type: Proposed Rule
Date: 2016-09-27
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to modify Class E airspace designated as a surface area at Findlay Airport, Findlay, OH; and Class E airspace extending upward from 700 feet above the surface at Ashland County Airport, Ashland, OH; Lakefield Airport, Celina, OH; Pickaway County Memorial Airport, Circleville, OH; Ross County Airport, Chillicothe, OH; Fairfield County Airport, Lancaster, OH; Defiancé Memorial Airport, Defiancé, OH; Findlay Airport; Bluffton Airport, Findlay, OH; Butler County Airport-Hogan Field, Hamilton, OH; Lima Allen County Airport, Lima, OH; and Madison County Airport, London, OH. Decommissioning of non-directional radio beacon (NDB), cancellation of NDB approaches, and implementation of area navigation (RNAV) procedures have made this action necessary for the safety and management of Instrument Flight Rules (IFR) operations at these airports. Additionally, the geographic coordinates at Port Columbus International Airport; Findlay Airport; Ashland County Airport; Samaritan Hospital Heliport, Ashland, OH; Lakefield Airport; Ross County Airport; Defiancé Regional Medical Center Heliport, Defiancé, OH; Bluffton Airport; Lima Allen County Airport; and St. Rita's Medical Center Heliport, Lima, OH, would be adjusted to coincide with the FAA's aeronautical database. Also, the names of Samaritan Hospital Heliport (formerly Samaritian Regional Health System), Defiancé Regional Medical Center Heliport (formerly Defiancé Hospital), and Butler County Regional Airport-Hogan Field (formerly Butler County Regional Airport) would be updated to coincide with the FAA's aeronautical database.
Repair Stations; Response to Public Comments
Document Number: 2016-23121
Type: Rule
Date: 2016-09-26
Agency: Federal Aviation Administration, Department of Transportation
This action confirms the effective date and adopts as final the interim final rule published on July 27, 2016, and responds to the comments received on that interim final rule. The rule removed the requirement that a repair station with an airframe rating provide suitable permanent housing to enclose the largest type and model aircraft listed on its operations specifications. The FAA also revised its general housing and facilities regulation to provide that a repair station's housing for its facilities, equipment, materials, and personnel must be consistent not only with its ratings, but also with its limitations to those ratings. Finally, the FAA added an additional general purpose limited rating to cover maintenance work not covered by the existing 12 limited rating categories.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: ATC Authorizations in Controlled Airspace Under Part 107
Document Number: 2016-23118
Type: Notice
Date: 2016-09-26
Agency: Federal Aviation Administration, Department of Transportation
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew a previously approved information collection. The FAA has established the ATC Authorization in Controlled Airspace under Part 107 portal to allow a remote pilot in command to request FAA authorization for a small unmanned aircraft to operate in Class B, C, D, and the lateral boundaries of the surface area of Class E airspace designated for an airport.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Mitsubishi MU-2B Series Airplane Special Training, Experience, and Operating Procedures
Document Number: 2016-23117
Type: Notice
Date: 2016-09-26
Agency: Federal Aviation Administration, Department of Transportation
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew a previously approved information collection. The collection of information is necessary to document participation, completion, and compliance with the pilot training program for the MU-2B under the newly published subpart N of part 91 which will replace SFAR No. 108.
Airworthiness Directives; Airbus Airplanes
Document Number: 2016-22460
Type: Rule
Date: 2016-09-26
Agency: Federal Aviation Administration, Department of Transportation
We are superseding Airworthiness Directive (AD) 2000-10-18 for certain Airbus Model A300 series airplanes; Model A300 B4-600, B4-600R, F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes); and Model A310 series airplanes. AD 2000-10-18 required repetitive inspections to detect cracks in the lower spar of the engine pylons between ribs 6 and 7, and repair if necessary. This new AD reduces the compliance times for the initial inspection and the repetitive intervals. This AD was prompted by the determination that the compliance times for the initial inspection and the repetitive intervals must be reduced to allow timely detection of cracks in the engine pylon's lower spar between ribs 6 and 7. We are issuing this AD to detect and correct fatigue cracking, which could result in reduced structural integrity of the engine pylon's lower spar, and possible separation of the engine from the airplane.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-22188
Type: Rule
Date: 2016-09-26
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. This AD was prompted by several reports of chafing of the wire bundles inside the electrical conduit of the forward and aft boost pumps of the numbers 1 and 4 main fuel tanks due to high vibration. These wire bundles can chafe through the wire sleeving into the insulation, exposing the wire conductors. This AD requires replacing the wire bundles inside the electrical conduit of the forward and aft boost pumps of the numbers 1 and 4 main fuel tanks with new, improved wire bundles inserted into conduit liners. This AD also requires adding a revision to the maintenance or inspection program, as applicable, to include critical design configuration control limitations (CDCCLs) for the fuel boost pump wiring. We are issuing this AD to prevent chafing of the wire bundles and subsequent arcing between the wiring and the electrical conduit creating an ignition source in the fuel tanks, which could result in a fire and consequent fuel tank explosion.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-22187
Type: Rule
Date: 2016-09-26
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 airplanes. This AD was prompted by a report of uncommanded movement by a captain's seat during a landing rollout due to a failure in the seat horizontal actuator. This AD requires repetitive tests of the captain and first officer seat assemblies for proper operation, and corrective action if necessary. This AD also requires installation of new captain and first officer seat assemblies, which terminates the repetitive tests. We are issuing this AD to prevent a seat actuator clutch failure, which could result in a loss of seat locking and uncommanded motion of the captain's or first officer's seat; uncommanded seat movement could result in reduced controllability of the airplane.
Airworthiness Directives; Airbus Airplanes
Document Number: 2016-21703
Type: Proposed Rule
Date: 2016-09-26
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for all Airbus Model A318-111 and -112 airplanes, Model A319-111, -112, -113, - 114, and -115 airplanes, Model A320-211, -212, and -214 airplanes, and Model A321-111, -112, -211, -212, and -213 airplanes. This proposed AD was prompted by reports of engine fan cowl door (FCD) losses on airplanes equipped with CFM56 engines due to operator failure to close the FCD during ground operations. This proposed AD would require modification and re-identification of certain FCDs or replacement of certain FCDs. This proposed AD would also require installation of a placard. We are proposing this AD to prevent in-flight loss of an engine FCD and possible consequent damage to the airplane.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-21602
Type: Rule
Date: 2016-09-26
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This AD was prompted by fuel system reviews conducted by the manufacturer. This AD requires installing an automatic shutoff system for the center and auxiliary tank fuel boost pumps, as applicable; installing a placard in the airplane flight deck if necessary; replacing the P5-2 fuel system module assembly; installing the ``uncommanded ON'' (UCO) protection system for the fuel boost pumps; revising the airplane flight manual (AFM) to advise the flight crew of certain operating restrictions for airplanes equipped with an automatic shutoff system; and revising the maintenance program by incorporating new airworthiness limitations for fuel tank systems to satisfy Special Federal Aviation Regulation No. 88 requirements. We are issuing this AD to prevent operation of the center and auxiliary tank fuel boost pumps with continuous low pressure, which could lead to friction sparks or overheating in the fuel pump inlet that could create a potential ignition source inside the center and auxiliary fuel tanks. These conditions, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Proposed Amendment of Class E Airspace for the Following Iowa Towns; Algona, IA; Ankeny, IA; Atlantic, IA; Belle Plane, IA; Creston, IA; Estherville, IA; Grinnell, IA; Guthrie Center, IA; and Oelwein, IA
Document Number: 2016-22889
Type: Proposed Rule
Date: 2016-09-23
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to modify Class E surface area at Ankeny Regional Airport, Ankeny, IA; and Class E airspace extending upward from 700 feet above the surface at Algona Municipal Airport, Algona, IA; Ankeny Regional Airport; Atlantic Municipal Airport, Atlantic, IA; Belle Plaine Municipal Airport, Belle Plaine, IA; Creston Municipal Airport, Creston, IA; Estherville Municipal Airport, Estherville, IA; Grinnell Regional Airport, Grinnell, IA; Guthrie County Regional Airport, Guthrie Center, IA; and Oelwein Municipal Airport, Oelwein, IA. Decommissioning of non- directional radio beacons (NDB), cancellation of NDB approaches, and implementation of area navigation (RNAV) procedures have made this action necessary for the safety and management of Instrument Flight Rules (IFR) operations at the above airports. Additionally, the geographic coordinates for Algona Municipal Airport, Atlantic Municipal Airport, and Grinnell Regional Airport would be adjusted to coincide with the FAA's aeronautical database. The name of Belle Plaine, IA, would also be adjusted to correct a misspelling in the legal description.
Airworthiness Directives; B-N Group Ltd. Airplanes
Document Number: 2016-22831
Type: Proposed Rule
Date: 2016-09-23
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for B-N Group Ltd. Models BN-2, BN-2A, BN-2A-2, BN-2A-3, BN-2A-6, BN-2A-8, BN- 2A-9, BN-2A-20, BN-2A-21, BN-2A-26, BN-2A-27, BN-2B-20, BN-2B-21, BN- 2B-26, BN-2B-27, BN-2T-4R, BN-2T, BN2A MK. III, BN2A MK. III-2, and BN2A MK. III-3 (all models on Type Certificate Data Sheets A17EU and A29EU) airplanes that would supersde AD 2016-06-01. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracks in the inner shell of certain pitot/ static pressure heads. We are issuing this proposed AD to change the model applicability due to errors found in AD 2016-06-01.
Amendment of Class E Airspace; Indiana, PA
Document Number: 2016-22749
Type: Rule
Date: 2016-09-23
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E Airspace at Indiana, PA, to accommodate the new runway at Indiana County Airport (Jimmy Stewart Field). This action enhances the safety and management of Instrument Flight Rules (IFR) operations at the airport. This action also updates the geographic coordinates of the airport.
Amendment of Class D and E Airspace, Falmouth, MA
Document Number: 2016-22748
Type: Rule
Date: 2016-09-23
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E airspace designated as an extension at Cape Cod Coast Guard Air Station, (formerly Otis ANGB), Falmouth, MA, as the Otis TACAN has been decommissioned, requiring airspace reconfiguration. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations at the airport. This action also updates the geographic coordinates of the airport in the existing Class D and E airspace areas, as well as Falmouth Airpark, Barnstable Municipal Airport-Boardman/Polando Field, Chatham Municipal Airport, Martha's Vineyard Airport, (formerly Martha's Vineyard Municipal Airport), and the BOGEY LOM.
Amendment of Class E Airspace; Glasgow, KY
Document Number: 2016-22746
Type: Rule
Date: 2016-09-23
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E Airspace at Glasgow, KY as the Beaver Creek Non-Directional Beacon (NDB) has been decommissioned, requiring airspace reconfiguration at Glasgow Municipal Airport. This action enhances the safety and management of Instrument Flight Rules (IFR) operations at the airport. This action also updates the geographic coordinates of the airport.
Amendment of Class D and Class E Airspace; Hagerstown, MD
Document Number: 2016-22744
Type: Rule
Date: 2016-09-23
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E Airspace Designated as an Extension to a Class D Surface Area by eliminating the Notice to Airmen (NOTAM) part time status for Hagerstown Regional Airport-Richard A. Henson Field, Hagerstown, MD, for the safety and management of IFR operations. Also, this action recognizes the name change to Hagerstown Regional Airport-Richard A. Henson Field, (formerly Washington County Regional Airport), Hagerstown, MD, and updates the geographic coordinates of the airport listed in Class D and E airspace.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-21397
Type: Proposed Rule
Date: 2016-09-23
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Boeing Model 727 airplanes. This proposed AD was prompted by fuel system reviews conducted by the manufacturer. This proposed AD would require modifying the fuel quantity indicating system (FQIS) to prevent development of an ignition source inside the body-mounted auxiliary fuel tanks due to electrical fault conditions. As an alternative to the modification, this proposed AD would allow deactivating the body-mounted auxiliary fuel tanks. We are proposing this AD to prevent ignition sources inside the body-mounted auxiliary fuel tanks, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-21396
Type: Proposed Rule
Date: 2016-09-23
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Boeing Model 707 airplanes and Model 720 and 720B series airplanes. This proposed AD was prompted by fuel system reviews conducted by the manufacturer. This proposed AD would require modifying the fuel quantity indicating system (FQIS) to prevent development of an ignition source inside the center fuel tank due to electrical fault conditions. We are proposing this AD to prevent ignition sources inside the center fuel tank, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Twentieth RTCA SC-223 Aeronautical Mobile Airport Communication System Plenary Calling Notice
Document Number: 2016-22826
Type: Notice
Date: 2016-09-22
Agency: Federal Aviation Administration, Department of Transportation
The FAA is issuing this notice to advise the public of a meeting of Twentieth RTCA SC-223 Aeronautical Mobile Airport Communication System Plenary Calling Notice.
Thirty Second RTCA SC-213 Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS)
Document Number: 2016-22825
Type: Notice
Date: 2016-09-22
Agency: Federal Aviation Administration, Department of Transportation
The FAA is issuing this notice to advise the public of a meeting of Thirty Second RTCA SC-213 Enhanced Flight Vision Systems/ Synthetic Vision Systems (EFVS/SVS).
Amendment of Class E Airspace, Ithaca, NY
Document Number: 2016-22741
Type: Rule
Date: 2016-09-22
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E airspace Designated as an Extension at Ithaca Tompkins Regional Airport, Ithaca, NY, by updating the geographic coordinates of the Ithaca VHF omnidirectional range/distance measuring equipment, (VOR/DME), and the airport, as well as changing the airport name. This is an administrative change and does not affect the boundaries or operating requirements of the airspace.
Amendment of Class D and E Airspace and Revocation of Class E Airspace; Sioux City, IA
Document Number: 2016-22738
Type: Rule
Date: 2016-09-22
Agency: Federal Aviation Administration, Department of Transportation
This action modifies the Class D and E airspace areas at Sioux Gateway/Col. Bud Day Field, Sioux City, IA, due to the decommissioning of the Gateway non-directional radio beacon (NDB) and cancellation of the NDB approaches at the airport. The Class E airspace area designated as an extension is being removed as it is no longer needed. Advances in Global Positioning System (GPS) capabilities have made this action necessary for the safety and management of Instrument Flight Rules (IFR) operations at the airport. This action also updates the geographic coordinates for Martin Field, NE., to coincide with the FAAs aeronautical database.
Revocation of Class E Airspace; Alliance, NE; and Amendment of Class E Airspace for the Following Nebraska Towns; Albion, NE; Alliance, NE; Gothenburg, NE; Holdrege, NE; Imperial, NE; Lexington, NE; and Millard Airport, Omaha, NE
Document Number: 2016-22736
Type: Rule
Date: 2016-09-22
Agency: Federal Aviation Administration, Department of Transportation
This action removes Class E surface area airspace at Alliance Municipal Airport, Alliance, NE; and modifies Class E airspace extending upward from 700 feet above the surface at Albion Municipal Airport, Albion, NE; Alliance Municipal Airport, Alliance, NE; Quinn Field, Gothenburg, NE; Brewster Field Airport, Holdrege, NE; Imperial Municipal Airport, Imperial, NE; Jim Kelly Field, Lexington, NE; and Millard Airport, Omaha, NE. Decommissioning of non-directional radio beacons (NDB), cancellation of NDB approaches, and implementation of area navigation (RNAV) procedures have made this action necessary for the safety and management of Instrument Flight Rules (IFR) operations at the above airports. This action also updates the geographic coordinates for Quinn Field, Imperial Municipal Airport, and Jim Kelly Field to coincide with the FAA's aeronautical database.
Amendment of Class D and E Airspace, and Revocation of Class E Airspace; Troy, AL
Document Number: 2016-22735
Type: Rule
Date: 2016-09-22
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class D and E airspace, and removes Class E airspace designated as an extension at Troy Municipal Airport at N. Kenneth Campbell Field (formerly Troy Municipal Airport), Troy, AL. The Troy VHF Omnidirectional Radio Range (VOR) has been decommissioned, therefore Class E extension airspace is no longer needed, and new Standard Instrument Approach Procedures have been developed, requiring adjustments in Class D airspace and Class E airspace extending upward from 700 feet above the surface at the airport. This action enhances the safety and airspace management of Instrument Flight Rules (IFR) operations at the airport. This action also updates the geographic coordinates of the airport and recognizes the name change of the airport.
Amendment of Class E Airspace, Truckee, CA
Document Number: 2016-22726
Type: Rule
Date: 2016-09-22
Agency: Federal Aviation Administration, Department of Transportation
This action establishes Class E surface area airspace and modifies Class E airspace extending upward from 700 feet above the surface at Truckee-Tahoe Airport, Truckee, CA, to increase safety and enhance existing instrument flight rules (IFR) operations in the immediate vicinity of the airport.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.