Federal Aviation Administration 2013 – Federal Register Recent Federal Regulation Documents

Results 551 - 600 of 1,699
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2013-20969
Type: Proposed Rule
Date: 2013-08-28
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 747-200B, -200C, -200F, -300, and 747SR series airplanes. This proposed AD was prompted by reports of cracks of both lower chords and web on certain outboard struts. This proposed AD would require repetitive inspections for cracking of the lower spar chords and web, web lower spar chord modification, which includes inspections for cracking of the lower spar chords, and repetitive post modification inspections for cracking of the lower spar web and chord; and applicable corrective actions. We are proposing this AD to prevent cracked chords and web on certain outboard struts, which, if the chord severs, could result in reduced structural integrity of the diagonal brace load path and of the strut-to-wing attachment, and consequent separation of a strut and engine from the airplane during flight.
Airworthiness Directives; Bombardier, Inc. Airplanes
Document Number: 2013-20968
Type: Proposed Rule
Date: 2013-08-28
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-102, -103, -106, -201, -202, -301, -311, and -315 series airplanes. This proposed AD was prompted by a report of a pilot commanding an in-flight engine shut down in response to a low oil pressure warning indication. Further investigation revealed the mounting studs in the engine mounted alternating current (AC) generator mounting plate were pulled out of position and the threaded interface in the plate was corroded. This proposed AD would require repetitive inspections for discrepancies on certain AC generator mounting adapters, and replacing discrepant adapters with serviceable ones. This proposed AD would also require revising the maintenance program to incorporate a repetitive task specified in certain temporary revisions. We are proposing this AD to detect and correct corrosion in the AC generator mounting plate, which could result in a gap between the AC generator and the generator mounting plate, and cause loss of engine oil and consequent engine failure.
Pilot Certification and Qualification Requirements for Air Carrier Operations; Correction
Document Number: 2013-20962
Type: Rule
Date: 2013-08-28
Agency: Federal Aviation Administration, Department of Transportation
The FAA is correcting a final rule published on July 15, 2013 (78 FR 42324). In that final rule, which became effective on the date of publication, the FAA amended its regulations to create new certification and qualification requirements for pilots in air carrier operations. The FAA inadvertently listed an incorrect amendment number for that final rule. This document corrects that error.
Petition for Exemption; Summary of Petition Received
Document Number: 2013-20922
Type: Notice
Date: 2013-08-28
Agency: Federal Aviation Administration, Department of Transportation
This notice contains a summary of a petition seeking relief from specified requirements of FAA'S regulations. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Airspace Designations; Incorporation by Reference
Document Number: 2013-20874
Type: Rule
Date: 2013-08-27
Agency: Federal Aviation Administration, Department of Transportation
This action amends Title 14 Code of Federal Regulations (14 CFR) part 71 relating to airspace designations to reflect the approval by the Director of the Federal Register of the incorporation by reference of FAA Order 7400.9X, Airspace Designations and Reporting Points. This action also explains the procedures the FAA will use to amend the listings of Class A, B, C, D, and E airspace areas; air traffic service routes; and reporting points incorporated by reference.
Airworthiness Directives; Beechcraft Corporation Airplanes
Document Number: 2013-20853
Type: Proposed Rule
Date: 2013-08-27
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Beechcraft Corporation (type certificate previously held by Hawker Beechcraft Corporation) Models 1900, 1900C, and 1900D airplanes. This proposed AD was prompted by reports of cracking in the front spar cap angles and hat section structure of the vertical stabilizer. This proposed AD would require inspections of the vertical stabilizer spar angles and hat section for cracks with corrective actions as necessary. We are proposing this AD to correct the unsafe condition on these products.
Airworthiness Directives; 328 Support Services GmbH (Type Certificate Previously Held by AvCraft Aerospace GmbH; Fairchild Dornier GmbH; Dornier Luftfahrt GmbH) Airplanes
Document Number: 2013-20845
Type: Proposed Rule
Date: 2013-08-27
Agency: Federal Aviation Administration, Department of Transportation
We propose to supersede airworthiness directive (AD) 2008-14- 16 that applies to certain 328 Support Services GmbH (Type Certificate Previously Held by AvCraft Aerospace GmbH; Fairchild Dornier GmbH; Dornier Luftfahrt GmbH) Model 328-100 and 328-300 airplanes. AD 2008- 14-16 currently requires installing warning placards on the inside of the passenger door and service doors and modifying the hinge supports and support struts of the passenger doors. Since we issued AD 2008-14- 16, we received reports that certain fasteners, which were installed as part of the modification, are the wrong length. This proposed AD would require replacing the fasteners which were installed as part of the modification with new fasteners of the correct length, adds new airplanes, and removes one airplane. We are proposing this AD to prevent incidents of inadvertent opening and possible detachment of a passenger door in-flight, resulting in damage to airframe and systems and loss of control of the airplane.
Occupational Safety and Health Standards for Aircraft Cabin Crewmembers
Document Number: 2013-20841
Type: Rule
Date: 2013-08-27
Agency: Federal Aviation Administration, Department of Transportation
This notice announces the availability of a new policy statement regarding the regulation of some occupational safety and health conditions affecting cabin crewmembers on aircraft by the Occupational Safety and Health Administration. This policy statement will enhance occupational safety and health in the aircraft cabin by establishing the extent to which the Occupational Safety and Health Administration requirements may apply to the working conditions of aircraft cabin crew while they are onboard aircraft in operation.
Airworthiness Directives; the Boeing Company Airplanes
Document Number: 2013-20840
Type: Proposed Rule
Date: 2013-08-27
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for all the Boeing Company Model 727 airplanes. This proposed AD is intended to complete certain mandated programs intended to support the airplane reaching its limit of validity (LOV) of the engineering data that support the established structural maintenance program. This proposed AD would require repetitive inspections for cracking of small repairs done on the vertical flange of the rib chord, repetitive inspections for cracking along the upper fillet radius of the rib chord, and a large repair or preventive modification if necessary. Accomplishment of a large repair or preventive modification would terminate the actions of the proposed AD. We are proposing this AD to prevent cracks in the rib upper chord, which could result in the inability of the wing structure to support the limit load condition, and consequent loss of structural integrity of the wing.
Airworthiness Directives; Lockheed Martin Corporation/Lockheed Martin Aeronautics Company Airplanes
Document Number: 2013-20731
Type: Rule
Date: 2013-08-27
Agency: Federal Aviation Administration, Department of Transportation
We are superseding an airworthiness directive (AD) for all Lockheed Martin Corporation/Lockheed Martin Aeronautics Company Model L-1011 series airplanes. AD 2005-15-01 required repetitive inspections to detect corrosion or fatigue cracking of certain structural elements of the airplane, corrective actions if necessary, and incorporation of certain structural modifications. This new AD reduces certain compliance times for the initial inspection and the repetitive inspection interval for certain airplanes. This AD was prompted by reports of small cracks in additional areas outside those addressed in AD 2005-15-01, prior to the inspection threshold required by the AD 2005-15-01. We are issuing this AD to prevent corrosion or fatigue cracking of certain structural elements, which could result in reduced structural integrity of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2013-20730
Type: Rule
Date: 2013-08-27
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This AD was prompted by a report of an in-service occurrence of total loss of boost pump pressure of the fuel feed system, followed by loss of fuel system suction feed capability on one engine, and in-flight shutdown of the engine. This AD requires repetitive operational tests of the engine fuel suction feed of the fuel system, and other related testing and corrective action if necessary. We are issuing this AD to detect and correct loss of the engine fuel suction feed capability of the fuel system, which in the event of total loss of the fuel boost pumps could result in dual engine flameout, inability to restart the engines, and consequent forced landing of the airplane.
Waiver to Space Exploration Technologies Corporation of Acceptable Risk Limit for Launch
Document Number: 2013-20726
Type: Notice
Date: 2013-08-27
Agency: Federal Aviation Administration, Department of Transportation
This notice concerns a petition for waiver submitted to the Federal Aviation Administration (FAA) by Space Exploration Technologies Corporation (SpaceX) to waive a limit that the risk to the public from the launch of an expendable launch vehicle not exceed an expected average number of 0.00003 casualties (Ec
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2013-20718
Type: Rule
Date: 2013-08-27
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 757 airplanes. This AD was prompted by two in- service occurrences on Model 737-400 airplanes of total loss of boost pump pressure of the fuel feed system, followed by loss of fuel system suction feed capability on one engine, and in-flight shutdown of the engine. This AD requires repetitive operational tests of the engine fuel suction feed of the fuel system, and corrective actions if necessary. We are issuing this AD to detect and correct loss of the engine fuel suction feed capability of the fuel system, which, in the event of total loss of the fuel boost pumps, could result in dual engine flameout, inability to restart the engines, and consequent forced landing of the airplane.
Proposed Modification of Class E Airspace; Prineville, OR
Document Number: 2013-20729
Type: Proposed Rule
Date: 2013-08-26
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to modify Class E airspace at Prineville, OR, to accommodate aircraft using Area Navigation (RNAV) Global Positioning System (GPS) standard instrument approach procedures at Prineville Airport. A minor adjustment would also be made to the geographic coordinates of the airport. The FAA is proposing this action to enhance the safety and management of aircraft operations at the airport.
Notice of Meeting of the National Parks Overflights Advisory Group Aviation Rulemaking Committee
Document Number: 2013-20728
Type: Notice
Date: 2013-08-26
Agency: Federal Aviation Administration, Department of Transportation
The Federal Aviation Administration (FAA) and the National Park Service (NPS), in accordance with the National Parks Air Tour Management Act of 2000, as amended, announce the next meeting of the National Parks Overflights Advisory Group (NPOAG) Aviation Rulemaking Committee (ARC). This notification provides the date, format, and agenda for the meeting. Date and Location: The NPOAG ARC will hold a meeting on September 19, 2013. The meeting will be conducted as a telephone conference call. The meeting will be held from 10:00 a.m. to 12:00 p.m. Pacific Daylight Time. This NPOAG meeting will be open to the public. Interested persons may listen in on the conference call (see Public Participation at the Meeting).
Proposed Revocation of Class E Airspace; Danville, IL
Document Number: 2013-20722
Type: Proposed Rule
Date: 2013-08-26
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to remove Class E airspace at Danville, IL. The FAA has determined that, because of changes in the composition of flight operations at Vermilion Regional Airport, a Class E surface area is no longer needed to enhance the safety and management of Instrument Flight Rules (IFR) operations for standard instrument approach procedures at the airport.
Proposed Amendment of Class E Airspace; Gainesville, TX
Document Number: 2013-20719
Type: Proposed Rule
Date: 2013-08-26
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to amend Class E airspace at Gainesville, TX. Decommissioning of the Gainesville radio beacon (RBN) at Gainesville Municipal Airport has made reconfiguration necessary for standard instrument approach procedures and for the safety and management of Instrument Flight Rules (IFR) operations at the airport.
Proposed Amendment of Class E Airspace; Del Rio, TX
Document Number: 2013-20716
Type: Proposed Rule
Date: 2013-08-26
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to amend Class E airspace at Del Rio, TX. Additional controlled airspace is necessary to accommodate new circling approach requirements at Laughlin Air Force Base (AFB). The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations for instrument approach procedures at the airport.
Airworthiness Directives; Bombardier, Inc. Airplanes
Document Number: 2013-20715
Type: Proposed Rule
Date: 2013-08-26
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This proposed AD was prompted by reports of fractured rudder pedal tubes installed on the pilot-side rudder bar assembly. This proposed AD would require repetitive inspections for cracking and damage of both pilot-side rudder pedal tubes, and replacement of affected pilot-side rudder bar assemblies if necessary. We are proposing this AD to detect and correct cracking of both pilot-side rudder pedal tubes, which could result in loss of pilot rudder pedal input causing reduced yaw controllability or a runway excursion.
Airworthiness Directives; Fokker Services B.V. Airplanes
Document Number: 2013-20585
Type: Proposed Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This proposed AD was prompted by three reports of cracking in the rear pressure bulkhead (RPBH) web. This proposed AD would require inspecting the RPBH web for cracking, and repairing if necessary. We are proposing this AD to detect and correct cracking of the RPBH web, which could result in in-flight decompression of the airplane and possible injury to the occupants.
Establishment of Class E Airspace; Umatilla, FL
Document Number: 2013-20512
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
This action establishes Class E Airspace at Umatilla, FL, to accommodate the Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedures at Umatilla Municipal Airport. This action enhances the safety and airspace management of Instrument Flight Rules (IFR) operations within the National Airspace System.
Amendment of Class E Airspace; Dayton, TN, Establishment of Class E Airspace; Cleveland, TN, and Revocation of Class E Airspace; Bradley Memorial Hospital, Cleveland, TN
Document Number: 2013-20499
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E Airspace at Dayton, TN, as the Hardwick Non-Directional Beacon (NDB) has been decommissioned and new Standard Instrument Approach Procedures (SIAPs) have been developed at Mark Anton Airport. Also, Hardwick Field Airport has closed; therefore, the controlled airspace area is removed. This action also establishes Class E Airspace at Cleveland Regional Jetport, Cleveland, TN, to accommodate area navigation (RNAV) global positioning system (GPS) SIAPs at the airport. Information regarding Bradley Memorial Hospital is added to the Cleveland, TN, airspace description and removed from both the Dayton, TN, regulatory text as well as its listing as Bradley Memorial Hospital, Cleveland, TN, to correct an erroneous reference.
Amendment of Class E Airspace; Plattsburgh, NY
Document Number: 2013-20498
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E Airspace at Plattsburg, NY, as the Clinton County Airport has closed and controlled airspace removed. New Class E Airspace at Plattsburgh International Airport is created to accommodate standard instrument approach procedures developed at the airport. Airspace reconfiguration is necessary for the safety and airspace management of Instrument Flight Rules (IFR) operations at the airport.
Amendment of Class D and E Airspace; Wrightstown, NJ
Document Number: 2013-20497
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class D and E Airspace at Wrightstown, NJ, by updating the geographic coordinates and changing the city identifier of McGuire Air Force Base (AFB) to aid in the navigation of our National Airspace System. This action is necessary for the continued safety and management of instrument flight rules (IFR) operations within the Wrightstown, NJ airspace area.
Airworthiness Directives; Embraer S.A. Airplanes
Document Number: 2013-19463
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Embraer S.A. Model ERJ 170 and ERJ 190 airplanes. This AD was prompted by reports of chafing between the auxiliary power unit (APU) electronic starter controller (ESC) power cables and the airplane tail cone firewall. This AD requires a detailed inspection for damage to the insulation and inner conductors of the APU ESC power cables, installing a new grommet support in the tail cone firewall, and corrective actions if necessary. We are issuing this AD to detect and correct damage to the APU ESC power cable harness, which if not corrected, could result in reduced structural integrity of the fuselage and empennage in the event of fire penetration through the firewall.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2013-19460
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 727, 727C, 727-100, 727-100C, 727-200, and 727- 200F series airplanes. This AD was prompted by a structural re- evaluation by the manufacturer, which identified elements within the wing trailing edge flap area that qualify as structural significant items (SSIs). This AD requires revising the maintenance inspection program to include inspections that will give no less than the required damage tolerance rating (DTR) for certain SSIs, and repairing any cracked structure. We are issuing this AD to detect and correct fatigue cracking of the wing trailing edge structure, which could result in compromised structural integrity of the airplane.
Airworthiness Directives; Airbus Airplanes
Document Number: 2013-19459
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Airbus Model A320-214, -232 and -233 airplanes; and Model A321-211, - 213, and -231 airplanes. This AD was prompted by a report of a missing fastener between certain stringers of the fuselage frame that connects the frame to a tee. This AD requires an inspection for a missing fastener, and a rototest inspection and a modification or repair of the fuselage frame at the affected area if necessary. We are issuing this AD to detect and correct cracking in the fuselage that could result in reduced structural integrity of the airplane.
Airworthiness Directives; Eurocopter Deutschland GmbH (ECD) Helicopters
Document Number: 2013-19443
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for ECD Model MBB-BK 117 C-2 helicopters. This AD requires inspecting the rigging of the power-boosted control system and, if there is a nonparallel gap between the rigging wedges and the inner sleeves, performing a rigging procedure. This AD was prompted by the discovery, during rigging of the main rotor controls, of movement of the longitudinal main rotor actuator piston after shut-down of the external pump drive. Such movement could cause incorrect rigging results. The actions of this AD are intended to prevent incorrect rigging results, which could impair freedom of movement of the upper controls and subsequent reduced control of the helicopter.
Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters
Document Number: 2013-19442
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for Eurocopter Deutschland GmbH (ECD) Model BO-105A, BO-105C, BO-105S, BO- 105LS A-1, BO-105LS A-3, MBB-BK 117 A-1, MBB-BK 117 A-3, MBB-BK 117 A- 4, MBB-BK 117 B-1, MBB-BK-117 B-2, and MBB-BK 117 C-1 helicopters to require inspections for corrosion or thread damage to each tail rotor balance weight (weight) and each tail rotor control lever (lever). This AD was prompted by a European Aviation Safety Agency (EASA) AD and a Transport Canada Civil Aviation (TCCA) AD, both issued based on a report that corrosion was detected on a weight in the area of the attachment thread on a model BO-105 helicopter. The actions of this AD are intended to detect corrosion and thread damage in the threaded area of the weight and lever, and to prevent failure of a weight or lever, separation of tail rotor parts, severe vibration, and subsequent loss of control of the helicopter.
Airworthiness Directives; Eurocopter France Helicopters
Document Number: 2013-19438
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model EC120B and EC130B4 helicopters with a certain emergency flotation gear (float) installed. This AD requires inspecting the float for chafing of the fabric covering and adding protectors to the float installation to prevent contact between the float and the protruding sections of the installation. This AD was prompted by a report of a float that would not inflate during overhaul because one of the float compartments was punctured due to chafing. The actions of this AD are intended to prevent failure of float and subsequent loss of control of the helicopter during an emergency water landing.
Airworthiness Directives; Airbus Airplanes
Document Number: 2013-19161
Type: Rule
Date: 2013-08-23
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for certain Airbus Model A330-300, A340-200, and A340-300 series airplanes. This AD was prompted by a determination that ballscrew rupture could occur on certain trimmable horizontal stabilizer actuators (THSAs). This AD requires repetitive THSA ballscrew shaft integrity tests, and replacement if necessary. We are issuing this AD to detect and correct ballscrew rupture, which, along with corrosion on the ballscrew lower splines, may lead to loss of transmission of THSA torque loads from the ballscrew to the tie-bar and consequent THSA blowback, which could result in loss of control of the airplane.
Proposed Amendment of Class D and E Airspace, and Establishment of Class E Airspace; Salisbury, MD
Document Number: 2013-20514
Type: Proposed Rule
Date: 2013-08-22
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to amend Class D and Class E airspace, and establish Class E airspace at Salisbury-Ocean City Wicomico Regional Airport, Salisbury, MD, due to the decommissioning of the Salisbury VHF Omnidirectional Radio Range Tactical Air Navigation Aid (VORTAC) and cancellation of the VOR approach. This action would enhance the safety and airspace management of Instrument Flight Rules (IFR) operations at the airport. This action also would update the airport's geographic coordinates, and change the Class D city designator.
Proposed Amendment of Class E Airspace; Olean, NY
Document Number: 2013-20511
Type: Proposed Rule
Date: 2013-08-22
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to amend Class E Airspace at Olean, NY, as the Olean Non-Directional Beacon (NDB) has been decommissioned, requiring airspace redesign at Cattaraugus County-Olean Airport. This action would enhance the safety and airspace management of Instrument Flight Rules (IFR) operations at the airport. This action also would update the geographic coordinates of the airport.
Proposed Establishment of Class E Airspace; Aliceville, AL
Document Number: 2013-20509
Type: Proposed Rule
Date: 2013-08-22
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to establish Class E Airspace at Aliceville, AL, to accommodate a new Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedure (SIAP) serving George Downer Airport. This action would enhance the safety and airspace management of Instrument Flight Rules (IFR) operations within the National Airspace System.
Proposed Amendment of Class E Airspace; Macon, GA
Document Number: 2013-20504
Type: Proposed Rule
Date: 2013-08-22
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to amend Class E Airspace at Macon, GA, as the Bay Creek NDB has been decommissioned and airspace reconfiguration is necessary for the safety and airspace management of Instrument Flight Rules (IFR) operations at Perry-Houston County Airport. This action also would amend controlled airspace and update the name and geographic coordinates of Macon Downtown Airport and amend controlled airspace for Middle Georgia Regional Airport.
Proposed Amendment of Class E Airspace; Cut Bank, MT
Document Number: 2013-20502
Type: Proposed Rule
Date: 2013-08-22
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to modify Class E airspace at Cut Bank Municipal Airport, Cut Bank, MT. Controlled airspace is necessary to accommodate aircraft using new Area Navigation (RNAV) Global Positioning System (GPS) standard instrument approach procedures at the airport. The geographic coordinates of the airport would be adjusted in the respective Class E airspace areas. The FAA is proposing this action to enhance the safety and management of aircraft operations at the airport.
Government/Industry Aeronautical Charting Forum Meeting
Document Number: 2013-20450
Type: Notice
Date: 2013-08-22
Agency: Federal Aviation Administration, Department of Transportation
This notice announces the bi-annual meeting of the Federal Aviation Administration (FAA) Aeronautical Charting Forum (ACF) to discuss informational content and design of aeronautical charts and related products, as well as instrument flight procedures development policy and design criteria.
Special Conditions: Boeing Model 777-200, -300, and -300ER Series Airplanes; Rechargeable Lithium Ion Batteries and Battery Systems
Document Number: 2013-20427
Type: Proposed Rule
Date: 2013-08-22
Agency: Federal Aviation Administration, Department of Transportation
This action proposes special conditions for the Boeing Model 777-200, -300, and -300ER series airplanes. These airplanes as modified by the ARINC Aerospace Company will have a novel or unusual design feature, specifically the rechargeable lithium ion batteries and battery system that will be used on an International Communications Group (ICG) ePhone cordless cabin handset. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Amendment of Class E Airspace; Fort Polk, LA
Document Number: 2013-20379
Type: Rule
Date: 2013-08-22
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E airspace at Fort Polk, LA. Additional controlled airspace is necessary to accommodate new Area Navigation (RNAV) Standard Instrument Approach Procedures at Polk Army Airfield (AAF). The airport's geographic coordinates are also adjusted. This action enhances the safety and management of Instrument Flight Rule (IFR) operations at the airport.
Amendment of Class E Airspace; Harlingen, TX
Document Number: 2013-20378
Type: Rule
Date: 2013-08-22
Agency: Federal Aviation Administration, Department of Transportation
This action amends Class E airspace at Harlingen, TX. Additional controlled airspace is necessary to accommodate new Area Navigation (RNAV) Standard Instrument Approach Procedures due to the decommissioning of the Sebas locator outer marker/nondirectional radio beacon (LOM/NDB) at Valley International Airport. The airport's name and geographic coordinates are also updated. This action enhances the safety and management of Instrument Flight Rule (IFR) operations at the airport.
Establishment of Class E Airspace; Stockton, KS
Document Number: 2013-20376
Type: Rule
Date: 2013-08-22
Agency: Federal Aviation Administration, Department of Transportation
This action establishes Class E airspace at Stockton, KS. Controlled airspace is necessary to accommodate new Area Navigation (RNAV) Standard Instrument Approach Procedures at Rooks County Regional Airport. The FAA is taking this action to enhance the safety and management of Instrument Flight Rule (IFR) operations at the airport.
34th Meeting: RTCA Special Committee 206, Aeronautical Information and Meteorological Data Link Services
Document Number: 2013-20433
Type: Notice
Date: 2013-08-21
Agency: Federal Aviation Administration, Department of Transportation
The FAA is issuing this notice to advise the public of the thirty-fourth meeting of the RTCA Special Committee 206, Aeronautical Information and Meteorological Data Link Services.
Twenty-Fourth Meeting: RTCA Special Committee 224, Airport Security Access Control Systems
Document Number: 2013-20424
Type: Notice
Date: 2013-08-21
Agency: Federal Aviation Administration, Department of Transportation
The FAA is issuing this notice to advise the public of the twenty-fourth meeting of the RTCA Special Committee 224, Airport Security Access Control Systems.
Seventeenth Meeting: RTCA Special Committee 217-Aeronautical Databases Joint With EUROCAE WG-44-Aeronautical Databases
Document Number: 2013-20423
Type: Notice
Date: 2013-08-21
Agency: Federal Aviation Administration, Department of Transportation
The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 217Aeronautical Databases being held jointly with EUROCAE WG-44Aeronautical Databases.
Seventh Meeting: RTCA Special Committee 227, Standards of Navigation Performance
Document Number: 2013-20420
Type: Notice
Date: 2013-08-21
Agency: Federal Aviation Administration, Department of Transportation
The FAA is issuing this notice to advise the public of the seventh meeting of the RTCA Special Committee 227, Standards of Navigation Performance.
Access to Aircraft Situation Display to Industry (ASDI) and National Airspace System Status Information (NASSI) Data
Document Number: 2013-20375
Type: Notice
Date: 2013-08-21
Agency: Federal Aviation Administration, Department of Transportation
In a proposal published on May 9, 2012, the FAA tentatively identified a process through which aircraft owners and operators could ask the FAA to limit the agency's dissemination of their aircraft data via the FAA's ASDI program.\1\ The FAA noted that its final decision on the policy will replace the interim policy to which the FAA has adhered since publishing it on December 16, 2011.\2\ After considering each of the comments submitted to the public docket in response to the proposal, the FAA is issuing this final policy with respect to the dissemination of aircraft data via ASDI.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Associate Administrator for Commercial Space Transportation (AST) Customer Service Survey
Document Number: 2013-20374
Type: Notice
Date: 2013-08-21
Agency: Federal Aviation Administration, Department of Transportation
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The FAA Office of the Associate Administrator for Commercial Space Transportation (AST) conducts this survey in order to obtain industry input on customer service standards which have been developed and distributed to industry customers.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Experimental Permits for Reusable Suborbital Rockets
Document Number: 2013-20373
Type: Notice
Date: 2013-08-21
Agency: Federal Aviation Administration, Department of Transportation
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The FAA collects information from applicants for experimental permits in order to determine whether they satisfy the requirements for obtaining an experimental permit under 14 CFR part 437.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Certification and Operations
Document Number: 2013-20372
Type: Notice
Date: 2013-08-21
Agency: Federal Aviation Administration, Department of Transportation
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. 14 CFR part 125 prescribes requirements for issuing operating certificates and for appropriate operating rules. In addition to the statutory basis, the collection of this information is necessary to issue, reissue, or amend applicant's operating certificates and operations specifications.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Airports Grants Program
Document Number: 2013-20369
Type: Notice
Date: 2013-08-21
Agency: Federal Aviation Administration, Department of Transportation
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The FAA collects information from airport sponsors and planning agencies in order to administer the Airports Grants Program. Data is used to determine eligibility, ensure proper use of Federal Funds, and ensure project accomplishment.