Federal Aviation Administration 2009 – Federal Register Recent Federal Regulation Documents

This action proposes to establish Class E airspace at Quinhagak, AK. Two Standard Instrument Approach Procedures (SIAPs) are being developed for the Quinhagak Airport at Quinhagak, AK. Additionally, one textual Obstacle Departure Procedure (ODP) is being developed. Adoption of this proposal would result in creating Class E airspace upward from 700 feet (ft.) above the surface at the Quinhagak Airport, Quinhagak, AK.

We are superseding an existing airworthiness directive (AD) for the specified ECD model helicopters that currently requires initial and repetitive inspections of the main rotor blade (blade) upper and lower surfaces for bulging. This AD results from mandatory continuing airworthiness information (MCAI) issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, based on reported incidents in which a balance weight migrated toward the tip of the blade. The MCAI states that new blades have become available that are not fitted with lead balance weights. The MCAI states that only blades equipped with a lead balance weight may result in the unsafe condition. This AD retains the requirements of the current AD but limits the applicability to those part-numbered blades that are fitted with lead balance weights. The actions are intended to limit the applicability to those blades fitted with lead balance weights that could detach, migrate, and cause severe vibrations leading to blade failure and subsequent loss of control of the helicopter.

This establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) to supersede AD 2008-12-16, which applies to certain M7 Aerospace LP SA226 and SA227 series airplanes. AD 2008-12-16 currently requires you to inspect wires and tube assemblies for chafing, arcing, or insufficient clearance between components. If chafing, arcing, or insufficient clearance between components is found, AD 2008-12-16 requires you to clear, repair, and/or replace all chafed wires, components, and tube assemblies. AD 2008-12-16 also requires you to cover the four-gauge wires leaving the battery box with firesleeving and secure them with a clamp. Since we issued AD 2008-12-16, M7 Aerospace LP has notified us that Model SA227-BC (C-26A) was inadvertently left out of the Applicability section of the AD, and they updated some of the service information due to parts availability. Operators have also identified issues with model applicability that needed clarification. Consequently, this AD retains the actions of AD 2008-12-16, adds Model SA227-BC (C-26A) to the Applicability section, and regroups the models for clarification. We are issuing this AD to detect and correct chafing of electrical wires, components, and tube assemblies. This condition could result in arcing of exposed wires with consequent burning of a hole in a hydraulic line or the bleed air line. This failure could lead to a hydraulic fluid leak and a possible fire in the engine nacelle compartment.

This action establishes Class D airspace and modifies Class E airspace at Flagler County Airport in Bunnell, FL. A new Federal Contract Air Traffic Control Tower is being built for Flagler County Airport. Class D Surface airspace is required to be established and after evaluation the existing Class E airspace will be modified to facilitate a more efficient operation. This rule increases the safety and management of the National Airspace System (NAS) around Flagler County Airport.

The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Boeing Model 747 series airplanes. The existing AD currently requires repetitive inspections to detect cracks in various areas of the fuselage internal structure, and related investigative/corrective actions if necessary. This proposed AD would require additional repetitive inspections for cracking of certain fuselage structure, and related investigative/corrective actions if necessary. This proposed AD results from fatigue tests and analysis by Boeing that identified areas of the fuselage where fatigue cracks can occur. We are proposing this AD to prevent the loss of the structural integrity of the fuselage, which could result in rapid depressurization of the airplane.

This document corrects the amendment number in the final rule published in the Federal Register on Friday, May 1, 2009. That final rule amends the regulations to allow the use of the published Obstacle Departure Procedures (ODP) or an alternative procedure or route assigned by Air Traffic Control (ATC). Also, that final rule amends the requirements to facilitate compliance and accurately reflect operating conditions in areas in which the terrain impedes communications.

The Federal Aviation Administration (FAA) is announcing the availability of Advisory Circular (AC) 187-1C which transmits an updated schedule of charges for services of FAA Flight Standards Aviation Safety Inspectors outside the United States. The advisory circular has been updated in accordance with the procedures listed in 14 CFR Part 187, Appendix A.

The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 206: Aeronautical Information Services Data Link.

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA proposes to supersede an existing airworthiness directive (AD) that applies to all Boeing Model 737-100, -200, -200C, - 300, -400, and -500 series airplanes. The existing AD currently requires a one-time inspection for scribe lines and cracks in the fuselage skin at certain lap joints, butt joints, external repair doublers, and other areas; and related investigative/corrective actions if necessary. This proposed AD would expand the area to be inspected and, for certain airplanes, require earlier inspections for certain inspection zones. This proposed AD results from additional detailed analysis of fuselage skin cracks adjacent to the skin lap joints on airplanes that had scribe lines; the analysis resulted in different inspection zones, thresholds and repetitive intervals, and airplane groupings. We are proposing this AD to prevent rapid decompression of the airplane due to fatigue cracks resulting from scribe lines on pressurized fuselage structure.

The FAA is adopting a new airworthiness directive (AD) for Hartzell Propeller Inc. steel hub turbine propellers, with any counterweight slug attachment bolts, part number (P/N) B-3386-14H, LFC manufacturing lot 224, installed. This AD requires identifying and removing all counterweight slug attachment bolts, P/N B-3386-14H, LFC manufacturing lot 224, from service and installing serviceable bolts. This AD results from two reports of failure of the bolts that attach the propeller blade counterweight slug, and separation of the counterweight slug which led to propeller vibration and damage to the propeller spinner. We are issuing this AD to prevent separation of the propeller blade counterweight slug, which could lead to injury and damage to the airplane.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

This action proposes to amend Class E airspace at Iowa Falls, IA. Additional controlled airspace is necessary to accommodate new Standard Instrument Approach Procedures (SIAPs) at Iowa Falls Municipal Airport, Iowa Falls, IA. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) aircraft operations at Iowa Falls Municipal Airport.

The Federal Aviation Administration (FAA) announces its determination that the noise exposure maps for Nashua Municipal Airport, as submitted by the Nashua Airport Authority under the provisions of Title I of the Aviation Safety and Noise Abatement Act of 1979 (Pub. L. 96-193) and 14 CFR Part 150, are in compliance with applicable requirements.

This supplemental NPRM revises an earlier proposed airworthiness directive (AD), applicable to Dowty Propellers Models R354/4-123-F/13, R354/4-123-F/20, R375/4-123-F/21, R389/4-123-F/25, R389/4-123-F/26, and R390/4-123-F/27 propellers. That proposed AD would have required initial and repetitive visual inspections of propeller blade root outer sleeves for cracks, and removal before further flight of propeller blades with cracked blade root outer sleeves. That proposed AD resulted from mandatory continuing airworthiness information (MCAI) issued by the European Aviation Safety Agency (EASA) to identify and correct an unsafe condition on certain Dowty propellers. This supplemental NPRM revises the proposed AD to correct the listing of propeller models affected. This supplemental NPRM results from the discovery that we need to correct one of the propeller model numbers affected, and to remove an erroneous propeller model number. We are proposing this AD to prevent blade counterweight release, which could result in injury or damage to the airplane. The MCAI describes the unsafe condition as:

This supplemental NPRM revises an earlier proposed airworthiness directive (AD), applicable to Dowty Propellers Models R354/4-123-F/13, R354/4-123-F/20, R375/4-123-F/21, R389/4-123-F/25, R389/4-123-F/26, and R390/4-123-F/27 propellers. That proposed AD would have required initial and repetitive visual inspections of propeller blade root outer sleeves for cracks, and removal before further flight of propeller blades with cracked blade root outer sleeves. That proposed AD resulted from mandatory continuing airworthiness information (MCAI) issued by the European Aviation Safety Agency (EASA) to identify and correct an unsafe condition on certain Dowty propellers. This supplemental NPRM revises the proposed AD to correct the listing of propeller models affected. This supplemental NPRM results from the discovery that we need to correct one of the propeller model numbers affected, and to remove an erroneous propeller model number. We are proposing this AD to prevent blade counterweight release, which could result in injury or damage to the airplane. The MCAI describes the unsafe condition as:

This notice announces a public meeting of the FAA's Aviation Rulemaking Advisory Committee (ARAC) to discuss transport airplane and engine (TAE) issues.

This notice announces the Office of Management and Budget's (OMB's) approval of the information collection requirement contained in the FAA's final rule, ``Drug Enforcement Assistance,'' which was published on February 28, 2008.

The Federal Aviation Administration (FAA) is amending an error in its security related regulations affecting the design and operation of transport category airplanes. The paragraph that describes the incorporation by reference of a document containing ballistic resistance requirements contains an erroneous cross reference which was included in both the final rule and the notice of proposed rulemaking. This document corrects that error so that the reader is able to locate the correct information.

The FAA proposes to rescind the final rule Congestion Management Rule for John F. Kennedy International Airport and Newark Liberty International Airport. The final rule established procedures to

This action amends the FAA's drug and alcohol regulations to place them in a new part. The FAA is not making any substantive changes to the drug and alcohol regulations in this rulemaking.

The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 186 Automatic Dependent Surveillance- Broadcast (ADS-B).

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: