Federal Aviation Administration November 8, 2019 – Federal Register Recent Federal Regulation Documents

Notice of Release of Land Affecting Federal Grant Assurance Obligations at Tucson International Airport, Tucson, Pima County, Arizona
Document Number: 2019-24452
Type: Notice
Date: 2019-11-08
Agency: Federal Aviation Administration, Department of Transportation
The Federal Aviation Administration (FAA) proposes to rule and invites public comment for the release of approximately 297 acres of airport land, otherwise known as Parcel H, at Tucson International Airport (TUS), Tucson, Pima County, Arizona from the aeronautical use provisions of the Grant Agreement Assurances since the land is not needed for airport purposes. The land for proposed release consists of two parcels along the southern boundary of the abandoned Hughes Access Road, adjacent to the main airport airfield sand campus, and a portion of property which is used by Aerospace Parkway. The land will be sold to the City of Tucson, to accommodate future expansion of a public roadway, and to permit future compatible development adjacent to United States Air Force Plant 44. The airport will be compensated for the fair market value of the land. The use of the land for a roadway and industrial development represents a compatible land use that will not interfere with the airport or its operation, thereby protecting the interests of civil aviation.
Airworthiness Directives; Ipeco Pilot and Co-Pilot Seats
Document Number: 2019-24378
Type: Rule
Date: 2019-11-08
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding Airworthiness Directive (AD) 2017-22-02 for certain Ipeco Holdings Limited (Ipeco) pilot and co-pilot seats. AD 2017-22-02 required modification and re-identification of the affected seats. This AD continues to require modification and re-identification of the affected seats. This AD also requires initial and repetitive inspections of the affected tracklock springs and, depending on the findings, replacement of the tracklock springs with a part eligible for installation. This AD was prompted by reports that the tracklock spring modification required by AD 2017-22-02 does not adequately address the issue of unexpected seat movement during takeoff and landing and the need to add additional seat part numbers (P/Ns) to the applicability. The FAA is issuing this AD to address the unsafe condition on these products.
Proposed Revocation of Class E Airspace; Grundy, VA
Document Number: 2019-24346
Type: Proposed Rule
Date: 2019-11-08
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to remove Class E airspace at Grundy, VA, as Grundy Municipal Airport has been abandoned, and controlled airspace is no longer required. This action would enhance the safety and management of controlled airspace within the national airspace system.
IFR Altitudes; Miscellaneous Amendments
Document Number: 2019-24345
Type: Rule
Date: 2019-11-08
Agency: Federal Aviation Administration, Department of Transportation
This amendment adopts miscellaneous amendments to the required IFR (instrument flight rules) altitudes and changeover points for certain Federal airways, jet routes, or direct routes for which a minimum or maximum en route authorized IFR altitude is prescribed. This regulatory action is needed because of changes occurring in the National Airspace System. These changes are designed to provide for the safe and efficient use of the navigable airspace under instrument conditions in the affected areas.
Airworthiness Directives; Airbus Helicopters
Document Number: 2019-24342
Type: Proposed Rule
Date: 2019-11-08
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for Airbus Helicopters Model AS332C, AS332C1, AS332L, and AS332L1 helicopters. This proposed AD would require inspecting the attachment screws of each main gearbox (MGB) suspension bar rear attachment fitting, and depending on the outcome, applying a sealing compound, performing further inspections, and replacing affected parts. This proposed AD is prompted by reports of an elongated attachment screw and loss of tightening torque of the nut. The actions of this proposed AD are intended to address an unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2019-24329
Type: Proposed Rule
Date: 2019-11-08
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. This proposed AD results from fuel system reviews conducted by the manufacturer. This proposed AD would require replacement of the bonding jumpers on the auxiliary power unit (APU) fuel pump. This proposed AD would also require, for certain airplanes, installation of a second bonding jumper; an inspection of the override/jettison fuel pumps and transfer/jettison fuel pumps to determine if the bonding jumper has a one-piece braid or two-piece braid and replacement of the bonding jumper if necessary; and replacement of the bonding jumper on the electrical scavenge fuel pump. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Gulfstream Aerospace Corporation Airplanes
Document Number: 2019-24324
Type: Rule
Date: 2019-11-08
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Gulfstream Aerospace Corporation (Gulfstream) Model G-IV and Model GIV-X airplanes. This AD was prompted by a revision to the airworthiness limitations section (ALS) of the aircraft maintenance manual (AMM) based on fatigue and damage tolerance testing and updated analysis. This AD requires revising the maintenance or inspection program to incorporate updated inspection requirements and life limits that address fatigue cracking of principal structural elements. The FAA is issuing this AD to address the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.