Federal Aviation Administration 2015 – Federal Register Recent Federal Regulation Documents

This action removes Class E surface area airspace designated as an extension to Class C airspace at Burbank-Glendale-Pasadena Airport, Burbank, CA. After reviewing the airspace, the FAA found no standard instrument approach procedures requiring Class E surface area airspace designated as an extension to the Class C airspace. This action enhances the safety and airspace management within the National Airspace System.

This action establishes Class E Airspace at Placida, FL, to accommodate new Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedures (SIAPs) serving Coral Creek Airport. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations at the airport.

We are adopting a new airworthiness directive (AD) for all General Electric Company (GE) GEnx-1B turbofan engine models. This AD was prompted by reports of GEnx-1B engine oil loss. This AD requires removal and replacement of the non-conforming ball valve in the oil filler cap. We are issuing this AD to prevent loss of engine oil, which could lead to failure of one or more engines, loss of thrust control, and damage to the airplane.

We propose to adopt a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model BAe 146 series airplanes and Model Avro 146-RJ series airplanes. This proposed AD was prompted by reports of cracking of the main fitting of the nose landing gear (NLG) and a determination that a new safe-life limitation for affected NLG main fittings has not been mandated. This proposed AD would require replacing affected NLG main fittings that have exceeded the safe-life limitation with a new or serviceable fitting. We are proposing this AD to prevent collapse of the NLG, which if not corrected, could lead to degradation of direction control on the ground or an un-commanded turn to the left, and a consequent loss of control of the airplane on the ground, possibly resulting in damage to the airplane and injury to occupants.

We propose to adopt a new airworthiness directive (AD) for all Airbus Model A330-200, -200 Freighter, and -300 series airplanes; and all Airbus Model A340-200, -300, -500, and -600 series airplanes. This proposed AD was prompted by a report of blockage of Angle of Attack (AOA) probes during climb, leading to activation of the Alpha Protection (Alpha Prot) while the Mach number increased. This activation could cause a continuous nose-down pitch rate that cannot be stopped with backward sidestick input, even in the full backward position. For certain airplanes, this proposed AD would require replacing certain AOA sensors (probes) with certain new AOA sensors. For certain other airplanes, this proposed AD would also require inspections and functional heat testing of certain AOA sensors for discrepancies, and replacement if necessary. We are proposing this AD to prevent erroneous AOA information and Alpha Prot activation due to blocked AOA probes, which could result in a continuous nose-down command and consequent loss of control of the airplane.

We are superseding Airworthiness Directive (AD) 2002-07-08 for certain The Boeing Company Model 737 airplanes. AD 2002-07-08 required repetitive inspections for cracking of the lower skin at the lower row of fasteners in the lap joints of the fuselage; repair of any cracking found; modification of the fuselage lap joints at certain locations, which terminated the repetitive inspections of the modified areas; and replacement of a certain preventive modification with an improved modification. This new AD adds repetitive inspections for cracking at certain window corner fastener holes, a preventive modification, and repair if necessary. This AD was prompted by the FAA's determination that certain modifications of the fuselage lap joints do not provide an adequate level of safety, and the subsequent discovery of cracks in additional fastener locations in the window belt skin panels, adjacent stringers, and window frames in locations outside the previous inspection area. We are issuing this AD to detect and correct fatigue cracking of the fuselage lap joints and window belt skin panels, which could result in reduced structural integrity and sudden decompression of the airplane.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. To obtain type certification of a rotorcraft, an applicant must show that the rotorcraft complies with specific certification requirements. To show compliance, the applicant must submit substantiating data.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The FAA Acquisition Management System establishes policies and internal procedures for FAA acquisition. The information collection is necessary to solicit, award, and administer contracts for supplies, equipment, services, facilities, and real property to fulfill FAA's mission.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. 14 CFR part 121 prescribes the requirements governing air carrier operations. The information collected is used to determine air operators' compliance with the minimum safety standards and the applicants' eligibility for air operations certification.

These special conditions are issued for the Boeing Model 787-9 airplane. This airplane will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport-category airplanes. This design feature is airbags mounted to structure to prevent serious injury. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

We propose to supersede airworthiness directive (AD) 2015-04- 03 that applies to certain Rolls-Royce plc (RR) RB211 Trent 768-60, 772-60, and 772B-60 turbofan engines. AD 2015-04-03 requires inspection of the sealing sleeve on the high-pressure/intermediate-pressure (HP/ IP) turbine support internal oil feed tube and removal of those sealing sleeves affected by AD 2015-04-03. This proposed AD would require removal of either the affected sealing sleeve only or both the affected sealing sleeve and the oil feed tube. We are proposing this AD to prevent failure of the HP/IP turbine support internal oil feed tube, which could lead to uncontained engine failure and damage to the airplane.

We are superseding Airworthiness Directive (AD) AD 2014-20-13 for certain Pacific Aerospace Limited Model 750XL airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as fatigue cracks on the fin forward pickup plates, which could cause it to fail. We are issuing this AD to require actions to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by a report of skin disbonding on a composite side shell panel of a rudder. This AD requires an inspection to determine if any rudder composite side shell panel has been repaired, a thermography inspection of each rudder that has received this repair, and related investigative and corrective actions if necessary. We are issuing this AD to detect and correct skin disbonding on the rudder, which could affect the structural integrity of the rudder, possibly resulting in reduced control of the airplane.

The FAA is correcting an airworthiness directive (AD) that published in the Federal Register. That AD applies to certain Schempp- Hirth Flugzeugbau GmbH Models Duo Discus and Duo Discus T gliders. The Model Duo Discus gliders were incorrectly referenced as powered sailplanes in the Applicability section. This document corrects that error and refers to both models as just gliders as in previous ADs. In all other respects, the original document remains the same; however we are publishing the entire rule in the Federal Register.

This Notice provides information to Federal, State, and local agencies; Native American tribes; and other interested persons regarding the FAA's intent to prepare an EIS to evaluate the potential environmental impacts of issuing a Launch Site Operator License to the Camden County Board of Commissioners for a proposed commercial space launch site (``Spaceport Camden''). The Camden County Board of Commissioners proposes to construct and operate Spaceport Camden in an unincorporated area of Woodbine, in Camden County, Georgia. The FAA will prepare the EIS in accordance with the National Environmental Policy Act of 1969 (NEPA; 42 United States Code 4321 et seq.), the Council on Environmental Quality Regulations for Implementing the Procedural Provisions of NEPA (40 Code of Federal Regulations parts 1500-1508), and FAA Order 1050.1F, Environmental Impacts: Policies and Procedures, as part of its licensing process. Concurrent with the NEPA process, the FAA is initiating National Historic Preservation Act Section 106 Consultation to determine the potential effects of the Proposed Action on historic properties. The FAA is also consulting with the U.S. Fish and Wildlife Service (USFWS) under Section 7 of the Endangered Species Act regarding potential impacts on federally-listed threatened and endangered species. Pursuant to the U.S. Department of Transportation Act of 1966, this EIS will comply with the requirements of Section 4(f) of the Act. Additional information is available online at: https://www.faa.gov/about/office_org/headquarters_offices/ast/ environmental/nepa_docs/review/documents_progress/camden_spac eport/.

This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

The FAA assigned the Aviation Rulemaking Advisory Committee (ARAC) a new task to provide recommendations regarding occupant protection rulemaking in normal and transport category rotorcraft for older certification basis type designs that are still in production. The FAA amended regulations to incorporate occupant protection rules, including those for emergency landing conditions and fuel system crash resistance, for new type designs in the 1980s and 1990s. These rule changes do not apply to newly manufactured rotorcraft with older type designs or to derivative type designs that keep the certification basis of the original type design. This approach has resulted in a very low incorporation rate of occupant protection features into the rotorcraft fleet, and fatal accidents remain unacceptably high. At the end of 2014, only 16% of U.S. fleet had complied with the crash resistant fuel system requirements effective 20 years earlier, and only 10% had complied with the emergency landing requirements effective 25 years earlier. A recent fatal accident study has shown these measures would have been effective in saving lives. This notice informs the public of the new ARAC activity and solicits membership for the new Rotorcraft Occupant Protection Working Group.

This action corrects an error in a final rule published in the Federal Register of October 19, 2015, by amending the magnetic bearing to a true bearing in the Class E surface area airspace description for Farmington Regional Airport, Farmington, MO.

We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 airplanes. This AD was prompted by reports of missing plugs found prior to airplane delivery, during manufacturing inspections, at various locations in certain stringers of the lower lobe cargo compartments. This AD requires drilling a hole and installing and bonding plugs in certain stringers of the lower lobe cargo compartments. We are issuing this AD to detect and correct missing or misaligned plugs which, in the event of a fire, could cause an increased rate of loss of Halon in the lower cargo compartments, and result in the inability to extinguish a fire and consequent loss of control of the airplane.

We are adopting a new airworthiness directive (AD) for certain Lockheed Martin Corporation/Lockheed Martin Aeronautics Company Model 188 series airplanes. This AD was prompted by an evaluation by the design approval holder (DAH) indicating that the circumferential fuselage splice at fuselage-station (FS) 695 is subject to widespread fatigue damage (WFD). This AD requires an inspection for corrosion and previous repairs, severed stringers, cracking, and loose or distressed fasteners of the forward and aft ends of the stringer splices of certain stringers, inspection for cracking and modification of certain fastener holes common to the stringer and splice member at the forward and aft ends of the splice, and related investigative and corrective actions if necessary. We are issuing this AD to prevent loss of residual strength of the circumferential fuselage splice at FS 695, which could lead to rapid decompression of the cabin and potential loss of the airplane.

This action proposes special conditions for the Kestrel Aircraft Company, Model K-350 Turboprop airplane. This airplane will have a novel or unusual design feature associated with the installation of a rechargeable lithium battery. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

These special conditions are issued for Embraer Model EMB-545 and EMB-550 airplanes. These airplanes will have a novel or unusual design feature associated with a seat configuration of side-facing seats positioned forward of aft-facing seats, and with a structural armrest between the side-facing and aft-facing seats. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

We propose to adopt a new airworthiness directive (AD) for certain Airbus Model A330-200, -200 Freighter, and -300 series airplanes; and Model A340-200 and -300 series airplanes. This proposed AD was prompted by reports that cracks were found on an adjacent hole of certain frames of the center wing box (CWB). This proposed AD would require removing fasteners, a rototest inspection of fastener holes, installing new fasteners; and if necessary, oversizing the holes and doing rototest inspections for cracks, and repairing any cracking that is found. We are proposing this AD to detect and correct cracking on certain holes of certain frames of the CWB, which could affect the structural integrity of the airplane.

We propose to adopt a new airworthiness directive (AD) for all The Boeing Company Model 767 airplanes. This proposed AD was prompted by a determination that certain splice plate locations of the aft pressure bulkhead web are hidden and cannot be inspected using existing manufacturer service information. This proposed AD would require repetitive open-hole high frequency eddy current (HFEC) inspections for cracking of the aft pressure bulkhead web. We are issuing this AD to detect and correct cracking in the aft pressure bulkhead web, which could result in rapid decompression and loss of structural integrity.