Federal Aviation Administration October 7, 2014 – Federal Register Recent Federal Regulation Documents

These special conditions are issued for the Hawker Beechcraft Model No. 400A airplane as modified by Nextant Aerospace. This modification will have a novel or unusual design feature associated with an installed emergency power supply and standby attitude module that use rechargeable lithium batteries and battery systems. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

We propose to adopt a new airworthiness directive (AD) for certain Beechcraft Corporation Model G58 airplanes. This proposed AD was prompted by reports of fuel leaks due to fuel cells that did not properly fit in Model G58 airplanes. This proposed AD would require inspecting for and replacing, as necessary, certain fuel cells. This proposed AD would also require inspecting and replacing parts, as necessary, of the left and right fuel system installations and correcting torques on fuel system fittings; and prohibit future installations of certain fuel cells. We are proposing this AD to correct the unsafe condition on these products.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

We are adopting a new airworthiness directive (AD) for Brantly International, Inc. (Brantly) Model B-2, Model B-2A, and Model B-2B helicopters with certain main rotor blades. This AD requires inspecting each main rotor (M/R) blade for a crack or delamination and removing the blade if a crack exists or if the delamination exceeds certain thresholds. This AD was prompted by multiple reports of M/R blade cracks and an incident in which a crack that originated near the M/R blade trailing edge resulted in the loss of a large section of the M/R blade. The actions of this AD are intended to prevent loss of the M/R blade and subsequent loss of control of the helicopter.

We are superseding Airworthiness Directive (AD) 75-20-06 for certain Alexandria Aircraft LLC (type certificate previously held by Bellanca Aircraft Corp., Viking Aviation, Inc., and Bellanca, Inc.) Models 14-19-3A, 17-30, 17-30A, 17-31, 17-31A, 17-31ATC, and 17-31TC airplanes. AD 75-20-06 required repetitively inspecting the aft fuselage structure near the top of the vertical side tubing, which connects the horizontal stabilizer carry-through to the upper fuselage longeron, for cracks and installing the manufacturer's service repair kit as a terminating action for the repetitive inspections to repair any cracks found. Since we issued AD 75-20-06, we have determined that installing the service kit has not prevented cracks from occurring. We have also determined that all affected airplane serial numbers should be included in the Applicability section. This AD requires continued repetitive inspections of the aft fuselage structure near the top of the vertical side tubing for cracks and making all necessary replacements of cracked parts. This AD also adds additional serial number airplanes to the Applicability section. We are issuing this AD to correct the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for Empresa Brasileira de Aeronautica S. A. (EMBRAER) Models EMB-110P1 and EMB- 110P2 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as corrosion and cracking on the rudder trim tab actuator terminal. We are issuing this AD to require actions to address the unsafe condition on these products.

We are superseding Airworthiness Directive (AD) 2011-07-05 for certain Sicma Aero Seat 9140, 9166, 9173, 9174, 9184, 9188, 9196, 91B7, 91B8, 91C0, 91C2, 91C4, 91C5, and 9301 series passenger seat assemblies; and Sicma Aero Seat 9501311-05, 9501301-06, 9501311-15, 9501301-16, 9501441-30, 9501441-33, 9501311-55, 9501301-56, 9501441-83, 9501441-95, 9501311-97, and 9501301-98 passenger seat assemblies. AD 2011-07-05 required a general visual inspection for cracking of backrest links, replacement with new links if cracking is found, and eventual replacement of all links with new links. This new AD requires a new general visual inspection for cracking of backrest links, which includes new seat backrest links; replacement with new links if cracking is found; and eventual replacement of all links with new links. This AD was prompted by a report that new seat backrest links could be affected by cracks similar to those identified on the backrest links with the previous design. We are issuing this AD to detect and correct cracks in the backrest links, which could affect the structural integrity of seat backrests. Failure of the backrest links could result in injury to an occupant during emergency landing conditions.