Federal Aviation Administration October 2013 – Federal Register Recent Federal Regulation Documents

We are superseding airworthiness directive (AD) 2004-18-06 for certain The Boeing Company Model 737-200, -200C, -300, -400, and -500 series airplanes. AD 2004-18-06 required repetitive inspections to find fatigue cracking of certain upper and lower skin panels of the fuselage, and follow-on and corrective actions if necessary. AD 2004- 18-06 also included a terminating action for the repetitive inspections of certain modified or repaired areas only. This new AD adds new inspections for cracking of the fuselage skin along certain chem-milled lines, and corrective actions if necessary. This new AD also reduces certain thresholds and intervals required by AD 2004-18-06. This AD was prompted by new findings of vertical cracks along chem-milled steps adjacent to the butt joints. We are issuing this AD to detect and correct fatigue cracking of the skin panels, which could result in sudden fracture and failure of the skin panels of the fuselage, and consequent rapid decompression of the airplane.

We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-100, -100B, -100B SUD, -200B, -200C, - 200F, -300, -400, -400D, -400F, and 747SR series airplanes. This AD was prompted by reports of cracking at the aft upper corner of the main entry door (MED) 5 cutout. This AD requires inspecting for the presence of repairs and measuring the edge margin at certain fastener locations around the upper aft corner of the door cutout, inspecting for any cracking of the fuselage skin assembly and bear strap in the aft upper corner area of the door cutout, and repairing or modifying the fuselage skin assembly and bear strap if necessary. We are issuing this AD to detect and correct cracking of the skin and bear straps at the aft upper corner of the MED 5 cutout, which could result in in-flight depressurization.

This notice contains a summary of a petition seeking relief from specified requirements of Title 14, Code of Federal Regulations (14 CFR). The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of the FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This notice announces the rescheduling of a public meeting of the FAA's Aviation Rulemaking Advisory Committee (ARAC) Transport Airplane and Engine (TAE) Subcommittee to discuss TAE issues. A number of issues have arisen that may affect the Committee's ability to have an effective meeting on October 2, 2013, including uncertainty regarding Federal Government shutdown and travel.

We are superseding airworthiness directive (AD) AD 2012-04-13, for all Rolls-Royce plc (RR) model RB211 Trent 553-61, 553A2-61, 556- 61, 556A2-61, 556B-61, 556B2-61, 560-61, and 560A2-61; and RB211 Trent 768-60, 772-60, and 772B-60; and RB211-Trent 875-17, 877-17, 884-17, 884B-17, 892-17, 892B-17, and 895-17; and RB211-524G2-T-19, -524G3-T- 19, -524H-T-36, and -524H2-T-19 turbofan engines that have a high- pressure (HP) compressor stage 1 to 4 rotor disc installed, with a certain part number (P/N) installed. AD 2012-04-13 required repetitive inspections of the axial dovetail slots and follow-on corrective action depending on findings. This new AD expands the population of affected parts. This AD also changes, for the purposes of this AD, the definition of ``engine shop visit.'' This AD was prompted by reports of additional affected HP compressor rotor discs that require the same action. We are issuing this AD to detect cracks in the HP compressor stage 1 and 2 disc posts, which could result in failure of the disc post and HP compressor blades, damage to the engine, and damage to the airplane.

We are adopting a new airworthiness directive (AD) for Eurocopter Model SA-365N, SA-365N1, AS-365N2, AS 365 N3, EC 155B, EC155B1, AS332C, AS332L, AS332L1, AS332L2, and EC225LP helicopters with certain EADS Sogerma pilot and co-pilot seats installed. This AD requires inspecting the rear beam of each seat to determine if all of the weld beads are present and replacing the seat if any weld bead is missing. This AD is prompted by a maintenance inspection that discovered a missing weld bead on the rear beam of a pilot seat. These actions are intended to prevent failure of the pilot and co-pilot seats and subsequent injury to the pilot or co-pilot.

We are superseding airworthiness directive (AD) 2012-26-51 for all Airbus Model A318, A319, A320, and A321 series airplanes. AD 2012- 26-51 required revising the airplane flight manual (AFM) to advise the flightcrew of emergency procedures for addressing angle of attack (AoA) sensor blockage, and also provided for optional terminating action for the AFM revision, which involves replacing AoA sensor conic plates with AoA sensor flat plates. This new AD requires replacing AoA sensor conic plates with AoA sensor flat plates, and subsequent removal of the AFM revision. This AD was prompted by a determination that replacement of AoA sensor conic plates is necessary to address the identified unsafe condition. We are issuing this AD to prevent reduced control of the airplane.

This action proposes to amend Class E airspace at Georgetown, TX. Decommissioning of the Georgetown radio beacon (RBN) at Georgetown Municipal Airport has made reconfiguration necessary for standard instrument approach procedures and for the safety and management of Instrument Flight Rules (IFR) operations at the airport.

This action proposes to amend Class E airspace at Burnet, TX. Decommissioning of the Burnet nondirectional radio beacon (NDB) at Burnet Municipal AirportKate Craddock Field has made reconfiguration necessary for standard instrument approach procedures and for the safety and management of Instrument Flight Rules (IFR) operations at the airport.

We are adopting a new airworthiness directive (AD) for Agusta Model AB139 and AW139 helicopters. This AD requires deactivating the Full Icing Protection System (FIPS) and installing a placard next to the FIPS controller stating that flight into known icing is prohibited. This AD is prompted by a report of a fire in the aft avionics bay and the baggage compartment resulting from an Auto Transformer Rectifier Unit internal circuit overload. These actions are intended to prevent a fire, structural damage, and subsequent loss of control of the helicopter.

We are adopting a new airworthiness directive (AD) for Robinson Model R22, R22 Alpha, R22 Beta, and R22 Mariner helicopters with certain fuel shut-off valves installed. This AD requires replacing the fuel shut-off valve with a newer design fuel shut-off valve. This AD is prompted by three accidents that occurred because the fuel shut- off valve was inadvertently moved to the ``off'' position. These actions are intended to prevent inadvertent closing of the fuel valve, which could result in engine power loss from which a safe landing may not be possible.