Federal Aviation Administration August 2012 – Federal Register Recent Federal Regulation Documents
Results 51 - 100 of 133
Airworthiness Directives; Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France Model EC155B and EC155B1 helicopters with a VIP 4- seat bench to require revising the Limitations section of the Rotorcraft Flight Manual (RFM) and converting the VIP 4-seat bench into a 3-seat configuration. This AD was prompted by the determination that the load strength of the seat attachment hardware of the seat installation does not meet certification specifications. The required actions are intended to prevent overloading of the seat structure at the attachment point during a hard landing or emergency landing, which could result in the VIP 4-seat bench detaching from the floor and subsequent injury to the seat occupants.
Airworthiness Directives; The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 757 airplanes. This AD was prompted by a report of extensive corrosion of the ballscrew of the drive mechanism of the horizontal stabilizer trim actuator. This AD requires repetitive detailed inspections for discrepancies of the horizontal stabilizer ballscrew assembly; repetitive lubrication of the horizontal stabilizer trim control system; repetitive measurements for discrepancies of the ballscrew to ballnut freeplay; and corrective actions, if necessary. We are issuing this AD to prevent undetected failure of the primary and secondary load paths for the ballscrew in the horizontal stabilizer, which could lead to loss of control of the horizontal stabilizer and consequent loss of control of the airplane.
Proposed Amendment of Class E Airspace; Pullman, WA
This action proposes to modify Class E airspace at Pullman/ Moscow Regional Airport, Pullman, WA. Controlled airspace is necessary to accommodate aircraft using Area Navigation (RNAV) Global Positioning System (GPS) standard instrument approach procedures at Pullman/Moscow Regional Airport, Pullman, WA. Also, the Pullman navigation aid would be removed from the airspace designation. The FAA is proposing this action to enhance the safety and management of aircraft operations at the airport.
Proposed Amendment of Class D and Class E Airspace; Lewiston, ID
The FAA is issuing a SNPRM for the notice of proposed rulemaking (NPRM) of June 4, 2012, in order to elicit comments addressing increasing further the controlled Class E airspace area at Lewiston-Nez Perce County Airport, Lewiston, ID. The NPRM proposed a modification of Class D airspace, and Class E airspace extending upward from 700 feet above the surface and 1,200 feet above the surface, and an adjustment to the geographic coordinates. This SNPRM would further enlarge the Class E airspace 1,200 feet above the surface area to enhance safety in the Lewiston-Nez Pearce County Airport, Lewiston, ID area.
Notice of Release From Federal Surplus Property and Grant Assurance Obligations at Porterville Municipal Airport, Porterville, CA
The Federal Aviation Administration (FAA) proposes to rule and invites public comment on the application for a release of approximately 26 acres of airport property at the Porterville Municipal Airport (Airport), Porterville, California from all conditions contained in the Surplus Property Deed and Grant Assurances because the parcel of land is not needed for airport purposes. The land requested to be released is located at the southwest corner of the airport and distant from the airfield. The land had previously been set aside as mitigation for a kit fox preserve, which prevented any airport activity on the property. The wildlife designation was recently eliminated allowing the City of Porterville (City) to acquire the property at its fair market value, thereby serving the interest of civil aviation. It will be developed for another purpose compatible with the airport and the new use will not interfere with the airport or its operation.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This proposed AD was prompted by a report of an approximate 8-inch crack found in the fuselage skin under the aft drain mast. This proposed AD would require a detailed inspection for cracking and corrosion of the channel and fillers adjacent to the drain mast bolts, an inspection to determine the location of the bonding strap, a measurement of the washers under the drain mast bolts, and related investigative actions and repair if necessary. We are proposing this AD to detect and correct cracking in the fuselage skin and internal support structure, which could result in uncontrolled decompression of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747- 200B, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes; Model 767-200, -300, -300F, and -400ER series airplanes; and Model 777-200, -200LR, -300, and -300ER series airplanes. This proposed AD was prompted by reports of burned Boeing Material Specification (BMS) 8-39 urethane foam, and a report from the airplane manufacturer that airplanes were assembled with seals throughout various areas of the airplane (including flight deck and cargo compartments) made of BMS 8-39 urethane foam, a material with fire-retardant properties that deteriorate with age. This proposed AD would require replacing seals made of BMS 8-39 urethane foam in certain areas of the airplane. We are proposing this AD to prevent the failure of urethane seals to maintain sufficient Halon concentrations in the cargo compartments to extinguish or contain fire or smoke, and to prevent penetration of fire or smoke in areas of the airplane that are difficult to access for fire and smoke detection or suppression.
Airworthiness Directives; The Boeing Company Airplanes
We propose to supersede an existing airworthiness directive (AD) that applies to all The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. The existing AD currently requires repetitive inspections to detect cracking of the lower corners of the door frame and cross beam of the forward cargo door, and corrective actions if necessary. The existing AD also requires eventual modification of the outboard radius of the lower corners of the door frame and reinforcement of the cross beam of the forward cargo door, which would constitute terminating action for the existing repetitive inspections. Since we issued that AD, we have received additional reports of fatigue cracking in the radius of the lower frames and in the lower number 5 cross beam of the forward cargo door. This proposed AD would revise the compliance times for the preventive modification; add certain inspections for cracks in the number 5 cross beam of the forward cargo door; and add inspections of the number 4 cross beam if cracks are found in the number 5 cross beam, and corrective actions if necessary. For certain airplanes, this proposed AD would also add a one-time inspection for airplanes previously modified or repaired, and a one-time inspection of the reinforcement angle for excessive shimming or fastener pull-up, and corrective actions if necessary. We are proposing this AD to prevent fatigue cracking of the lower corners of the door frame and number 5 cross beam of the forward cargo door, which could result in rapid depressurization of the airplane.
Proposed Provision of Navigation Services for the Next Generation Air Transportation System (NextGen) Transition to Performance-Based Navigation (PBN); Disposition of Comments
On December 15, 2011, the FAA published a Federal Register Notice (76 FR 77939) requesting comments on the FAA's plans for providing PBN services, and particularly the transition from the current Very High Frequency Omnidirectional Ranges (VOR) and other legacy navigation aids (NAVAIDS) to Area Navigation (RNAV)-based airspace and procedures. This action responds to the public comments the FAA received.
Third Meeting: RTCA Special Committee 227, Standards of Navigation Performance, (Joint With EUROCAE WG-85)
The FAA is issuing this notice to advise the public of the third meeting of RTCA Special Committee 227, Standards of Navigation Performance, (Joint with EUROCAE WG-85).
Airworthiness Directives; Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD was prompted by reports of jamming/malfunctioning of the left-hand engine thrust control mechanism. This AD requires modifying the left-hand engine upper core-cowl. We are issuing this AD to prevent jamming/malfunctioning of the left-hand engine thrust control mechanism, which could lead to loss of control of the airplane.
Airworthiness Directives; Cessna Aircraft Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Cessna Aircraft Company Models 172R and 172S airplanes. This proposed AD was prompted by reports of chafed fuel return line assemblies, which were caused by the fuel return line assembly rubbing against the right steering tube assembly during full rudder pedal actuation. This proposed AD would require you to inspect the fuel return line assembly for chafing; replace the fuel return line assembly if chafing is found; inspect the clearance between the fuel return line assembly and both the right steering tube assembly and the airplane structure; and adjustment as necessary. We are proposing this AD to correct the unsafe condition on these products.
Twenty-Second Meeting: RTCA Special Committee 203, Unmanned Aircraft Systems
The FAA is issuing this notice to advise the public of the twenty-second meeting of RTCA Special Committee 203, Unmanned Aircraft Systems.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Repair Stations; Extension of Comment Period
This action extends the comment period for an NPRM that was published on May 21, 2012. In that document, the FAA proposed to update and revise the regulations for repair stations. This extension is a result of formal requests from repair stations and industry associations to extend the comment period to the proposal. This extension is necessary to afford all interested parties an opportunity to present their views on the proposed rulemaking.
Nineteenth Meeting: RTCA Special Committee 216, Aeronautical Systems Security (Joint Meeting With EUROCAE WG-72)
The FAA is issuing this notice to advise the public of the nineteenth meeting of RTCA Special Committee 216, Aeronautical Systems Security (Joint Meeting with EUROCAE WG-72).
Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters
The FAA is correcting an airworthiness directive (AD) that was published in the Federal Register. That AD applies to Eurocopter Deutschland GmbH Model MBB-BK 117 C-2 helicopters. A page reference of the rotorcraft flight manual in the Required Actions section, paragraph (e)(1)(i), is incorrect. This document corrects that error. In all other respects, the original document remains the same.
Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals
The FAA publishes a monthly notice, as appropriate, of PFC approvals and disapprovals under the provisions of the Aviation Safety and Capacity Expansion Act of 1990 (Title IX of the Omnibus Budget Reconciliation Act of 1990) (Pub. L. 101-508) and Part 158 of the Federal Aviation Regulations (14 CFR part 158). This notice is published pursuant to paragraph d of Sec. 158.29.
Establishment of Class E Airspace; Chenega Bay, AK
This action establishes Class E airspace at Chenega Bay, AK, to accommodate aircraft using a new Area Navigation (RNAV) Global Positioning System (GPS) standard instrument approach procedures at Chenega Bay Airport. This improves the safety and management of Instrument Flight Rules (IFR) operations at the airport.
Amendment of Class D Airspace; Sault Ste Marie, ON
This action amends Class D airspace at Sault Ste Marie, ON. Additional controlled airspace is necessary to coincide with the Canadian control zone over Sault Ste Marie Airport. The FAA is taking this action to enhance the safety and management of Instrument Flight Rule (IFR) operations at the airport.
Airworthiness Directives; Sikorsky Aircraft Corporation Helicopters
We are adopting a new airworthiness directive (AD) for Sikorsky Aircraft Corporation (Sikorsky) Model S-76A helicopters to require modifying the electric rotor brake (ERB) and inserting changes into the ``Normal Procedures'' and ``Emergency Procedures'' sections of the Rotorcraft Flight Manual (RFM). This AD was prompted by a fire in the main gearbox area as a result of a hot electric rotor brake (ERB). The actions are intended to prevent overheating of the ERB, ignition of the ERB hydraulic fluid, a fire in the main gearbox area, and subsequent loss of control of the helicopter.
Airworthiness Directives; The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 707 airplanes, and Model 720 and 720B series airplanes. This AD was prompted by reports of cracking of the midspar fittings, and of the engine and nacelle strut separating from the airplane. This AD requires performing a detailed inspection of the midspar fittings of the nacelle strut to confirm that the correct part number is installed, and installing the correct part number if necessary; performing repetitive high frequency eddy current (HFEC) inspections of the midspar fittings of the nacelle strut for cracks, and repair if necessary; and performing repetitive general visual inspections of the nacelle struts to verify that the nacelle strut has not drooped below its normal position, applying the droop stripe to the nacelle strut and sailboat fairing if necessary, and performing repair if necessary. We are issuing this AD to detect and correct cracking of the midspar fitting, which could result in separation of the nacelle strut and engine from the airplane while in flight, and consequent loss of controllability of the airplane.
Airworthiness Directives; Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A318-112 and -121 airplanes; Model A319-111, -112, -115, - 132, and -133 airplanes; Model A320-214, -232, and -233 airplanes; and Model A321-211, -212, -213, and -231 airplanes. This AD was prompted by reports that some nuts installed on the wing, including on primary structural elements, were found cracked. This AD requires inspecting to determine if certain nuts are installed or cracked, and replacing the affected nuts if necessary. We are issuing this AD to detect and correct missing and cracked nuts, which could result in the structural integrity of the airplane wings being impaired.
Amendment to Class B Airspace; Salt Lake City, UT
This action modifies the Salt Lake City, UT, Class B airspace to contain aircraft conducting Instrument Flight Rules (IFR) instrument approach procedures to Salt Lake City International Airport (SLC), Salt Lake City, UT. The FAA is taking this action to improve the flow of air traffic, enhance safety, and reduce the potential for midair collision, while accommodating the concerns of airspace users. Further, this effort supports the FAA's national airspace redesign goal of optimizing terminal and en route airspace to reduce aircraft delays and improve system capacity. Minor corrections have been made to the geographic coordinates of the affected legal descriptions, as well as editorial corrections.
Airworthiness Directives; Embraer S.A. Airplanes
We are superseding two existing airworthiness directives (AD) for all Embraer S.A. Model ERJ 170 and ERJ 190 airplanes. Those ADs currently require revising the airplane flight manual (AFM) to introduce limitations for the use of auxiliary power unit (APU) bleed and to prohibit dispatch with a failed air management system (AMS) controller card. This new AD requires replacing the AMS controller processor module with one containing new software, and a new AFM revision. This AD was prompted by reports of the possible loss of automatic activation of the engine inlet ice protection system. We are issuing this AD to prevent the possibility of a right-hand (RH) engine compressor stall after the APU becomes the active bleed source for the left side, which may result in an engine failure; and to prevent the intermittent communication failure between the AMS controller cards and both secondary power distribution assemblies (SPDAs), which could lead to the loss of automatic activation of the engine inlet ice protection system when flying in icing conditions, which could result in ice accretion in the engine inlet and subsequent dual engine failure.
Proposed Amendment of Class E Airspace; Marysville, OH
This action proposes to amend Class E airspace at Marysville, OH. Additional controlled airspace is necessary to accommodate new Standard Instrument Approach Procedures (SIAP) at Union County Airport. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations for SIAPs at the airport.
Proposed Amendment of Class E Airspace; Forest City, IA
This action proposes to amend Class E airspace at Forest City, IA. Additional controlled airspace is necessary to accommodate new Standard Instrument Approach Procedures (SIAP) at Forest City Municipal Airport. Also, this action would update the geographic coordinates of the Forest City nondirectional radio beacon (NDB). The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations for SIAPs at the airport.
Public Notice for Waiver Of Aeronautical Land-Use Assurance; Sidney Municipal Airport, Sidney, OH
The Federal Aviation Administration (FAA) is considering a proposal to change a portion of the airport from aeronautical use to non-aeronautical use and to authorize the sale of the airport property. The proposal consists of 1 parcel of land totaling approximately 37.744 acres. The land is currently used for agricultural crop production. No facilities are located within the property boundaries. The land was acquired under FAA Project Number 3-39-0044-01. The aforementioned land is not needed for aeronautical use, as shown on the Airport Layout Plan. There are no impacts to the airport by allowing the airport to dispose of the property. Approval does not constitute a commitment by the FAA to financially assist in the disposal of the subject airport property nor a determination of eligibility for grant-in-aid funding from the FAA. The disposition of proceeds from the disposal of the airport property will be in accordance with FAA's Policy and Procedures Concerning the Use of Airport Revenue, published in the Federal Register on February 16, 1999. In accordance with section 47107(h) of title 49, United States Code, this notice is required to be published in the Federal Register 30 days before modifying the land-use assurance that requires the property to be used for an aeronautical purpose.
Public Notice for Waiver Of Aeronautical Land-Use Assurance; Springfield-Beckley Municipal Airport, Springfield, OH
The Federal Aviation Administration (FAA) is considering a proposal to change a portion of the airport from aeronautical use to non-aeronautical use and to authorize the sale of the airport property. The proposal consists of 3 parcels of land totaling approximately 12.66 acres. The land is currently used for agricultural crop production and airport perimeter fence. No facilities are located within the property boundaries. Federal funds were not used to purchase the property and is not needed for aeronautical use, as shown on the Airport Layout Plan. There are no impacts to the airport by allowing the sponsor to dispose of the property. Subject land will provide for the realignment and right-of-way needs of State Route 794. Approval does not constitute a commitment by the FAA to financially assist in the disposal of the subject airport property nor a determination of eligibility for grant- in-aid funding from the FAA. The disposition of proceeds from the sale of the airport property will be in accordance with FAA's Policy and Procedures Concerning the Use of Airport Revenue, published in the Federal Register on February 16, 1999. In accordance with section 47107(h) of title 49, United States Code, this notice is required to be published in the Federal Register 30 days before modifying the land-use assurance that requires the property to be used for an aeronautical purpose.
Airworthiness Directives; Airbus Airplanes
We propose to adopt a new airworthiness directive (AD) for all Airbus Model A318-111 and -112 airplanes, and Model A319, A320, and A321 series airplanes. This proposed AD was prompted by reports of silicon particles inside the oxygen generator manifolds, which had chafed from the mask hoses during installation onto the generator outlets. This proposed AD would require identifying the part number and serial number of each passenger oxygen container, replacing the oxygen generator manifold of the affected oxygen container with a serviceable manifold, and performing an operational check of the manual mask release and corrective actions if necessary. We are proposing this AD to detect and correct non-serviceable oxygen generator manifolds, which could reduce or block the oxygen supply, which could result in injury to passengers when oxygen supply is needed.
Airworthiness Directives; Bombardier, Inc. Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-400, -401, and -402 airplanes. This proposed AD was prompted by reports of an in-service incident where the propeller de-icing system became unavailable due to burnt/ chafed wires within the alternating current contractor box (ACCB). This proposed AD would require inspection for chafing, damage, and loose wiring within an ACCB and repair if necessary; and would require rework and re-identification of the wiring installation within each ACCB. We are proposing this AD to detect and correct damaged, chafed, or loose wiring within an ACCB, which could affect the operation of the windshield heater, ice detector, angle of attack (AOA) vane heater, pilot probe heater, engine intake heater, or propeller de-icing system, and subsequently adversely affect the airplane's flight characteristics in icing conditions.
Airworthiness Directives; The Boeing Company Airplanes
We propose to supersede an existing airworthiness directive (AD) that applies to certain The Boeing Company Model 757 airplanes equipped with Rolls-Royce RB211-535E engines. The existing AD currently requires repetitive inspections for signs of damage of the aft hinge fittings and attachment bolts of the thrust reversers, and related investigative and corrective actions if necessary. The existing AD also provides for an optional terminating modification for the repetitive inspections. Since we issued the existing AD, we have received reports of incorrectly installed washers under the attachment bolts of the aft hinge fittings of the thrust reversers. For certain airplanes, this proposed AD would add a one-time inspection of the washers installed under the attachment bolts of the aft hinge fittings for correct installation sequence, and reinstallation if necessary. This proposed AD also adds an option for installing a redesigned aft hinge fitting with the trim already done, instead of trimming an existing or new hinge fitting, which is included in the existing optional terminating modification. We are proposing this AD to prevent failure of the attachment bolts and consequent separation of a thrust reverser from the airplane during flight, which could result in structural damage to the airplane.
Airworthiness Directives; Revo, Incorporated Airplanes
We propose to supersede an existing airworthiness directive (AD) that applies to certain Revo, Incorporated Models COLONIAL C-1, COLONIAL C-2, LAKE LA-4, LAKE LA-4A, LAKE LA-4P, and LAKE LA-4-200 airplanes. The existing AD currently requires a one-time dye-penetrant inspection of the horizontal stabilizer attachment fitting and repetitive visual inspections of the fitting for any evidence of fretting, cracking, or corrosion (with necessary replacement and modification); replacement of the fitting upon reaching the 850-hours time-in-service (TIS) safe life; and reporting to the FAA the results of the initial inspection and any cracks found on repetitive inspections. Since we issued AD 2005-12-02, Revo, Incorporated informed the FAA that while the drawing numbers are different, the attachment fittings on the Model COLONIAL C-1 airplanes are identical in every other respect to those installed on the airplanes referenced in AD 2005-12-02. This proposed AD would retain the actions required by AD 2005-12-02, add the Model COLONIAL C-1 airplanes to the Applicability, and add an optional terminating action for the requirements. We are proposing this AD to correct the unsafe condition on these products.
Categorical Exclusion From Further Environmental Review for Standard Terminal Arrival Route Procedures for Ronald Reagan Washington National Airport
The FAA is issuing this notice to advise the public of its environmental review of two standard terminal arrival route (STAR) procedures, and one conventional arrival procedure, at Ronald Reagan Washington National Airport (DCA). As required by the National Environmental Policy Act, an evaluation has been performed on the three proposed procedures to determine the level of environmental review warranted. The FAA has elected to ``Categorically Exclude from further environmental review'' the three proposed arrival procedures identified as FRDMM1 (RNAV), TRUPS1 (RNAV) and NUMMY.
Categorical Exclusion From Further Environmental Review for Standard Terminal Arrival Route Procedures and Standard Instrument Departure Procedures for Washington Dulles International Airport
The FAA is issuing this notice to advise the public of its environmental review of two standard terminal arrival route (STAR) procedures and two standard instrument departure (SID) procedures at Washington Dulles International Airport (IAD). As required by the National Environmental Policy Act, an evaluation has been performed on the two proposed STAR procedures and the two proposed SID procedures to determine the level of environmental review warranted. The FAA has elected to ``Categorically Exclude from further environmental review'' the proposed STAR procedures identified as GIBBZ (RNAV) STAR and DOCCS STAR and the proposed SID procedures identified as RNLDI (RNAV) SID (previously named BLUES ONE (RNAV) SID) and BUNZZ ONE (RNAV) SID.
Airworthiness Directives; General Electric Company Turbofan Engines
We propose to supersede an existing airworthiness directive (AD) that applies to certain General Electric Company (GE) CF6-80C2 series turbofan engines. The existing AD requires replacement of the fuel tubes connected to the fuel flowmeter. Since we issued that AD, we received several additional reports of fuel leaks and two reports of engine fire due to mis-assembled supporting brackets on the fuel tube connecting the flowmeter to the Integrated Drive Generator (IDG) fuel- oil cooler. This proposed AD would require installing a new simplified one-piece bracket to eliminate mis-assembly. We are proposing this AD to prevent high-pressure fuel leaks caused by improper seating of fuel tube flanges, which could result in an engine fire and damage to the airplane.
Petition for Exemption; Summary of Petition Received
This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Petition for Exemption; Summary of Petition Received
This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of any petition or its final disposition.
Establishment of Class E Airspace; Fort Morgan, CO
This action establishes Class E airspace at Fort Morgan, CO, to accommodate aircraft using a new Area Navigation (RNAV) Global Positioning System (GPS) standard instrument approach procedures at Fort Morgan Municipal Airport. This improves the safety and management of Instrument Flight Rules (IFR) operations at the airport.
Membership in the National Parks Overflights Advisory Group Aviation Rulemaking Committee
By Federal Register notice (See 77 FR 27835-27836; May 11, 2012) the National Park Service (NPS) and the Federal Aviation Administration (FAA) invited interested persons to apply to fill six upcoming openings on the National Parks Overflights Advisory Group (NPOAG) Aviation Rulemaking Committee (ARC). The notice invited interested persons to apply to fill six vacancies representing commercial air tour operators (2), general aviation (1), Native American tribal (1), and environmental (2) concerns due to the incumbent members' completion of three-year term appointments on October 9, 2012. This notice informs the public of the persons selected to fill five of the six vacancies on the NPOAG ARC. Vacancies filled include the two commercial tour operator openings, the general aviation opening, the tribal opening, and one of the environmental openings. Since the previous notice did not draw enough responses from individuals for the remaining environmental vacancy, NPS and FAA are also using this notice to invite other interested individuals to apply for the remaining environmental opening. If you responded to the initial notice for the environmental openings, you will still be under consideration and need not re-apply.
Special Conditions: Eurocopter France, EC130T2; Use of 30-Minute Power Rating
These special conditions are issued for the Eurocopter France Model EC130T2 helicopter. This model helicopter will have the novel or unusual design feature of a 30-minute power rating, generally intended to be used for hovering at increased power for search and rescue missions. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Notice of a Change in Direction Finder Availability in Alaska
This Notice Announcement is a request for public comment on a proposal to decommission all 29 Direction Finders (DF) and the associated DF approaches in Alaska. DF usage for pilot orientation has become almost non-existent. Since 2004, the Alaska Flight Service Information Area Group (AFSIAG) has documented eight flight assists that involved lost or disoriented pilots. Of these, the use of DF equipment was documented three times. Since 2008, there have been no flight assists, nor usage of DF equipment for orientation services. Newer technologies such as Global Positioning System (GPS) and Automatic Dependent SurveillanceBroadcast (ADSB) have reduced the utilization of DF steers. Flight Service Stations have other tools available to assist lost or disoriented pilots, such as VOR, ADF, and GPS, that meet the needs of our aviation community. DF equipment is beyond its useful lifecycle.
Public Notice for Waiver of Aeronautical Land-Use Assurance; Southern Illinois Airport, Carbondale, IL
The Federal Aviation Administration (FAA) is considering a proposal to change a portion of airport land from aeronautical use to non-aeronautical use at the Southern Illinois Airport in Carbondale, Illinois. The proposal consists of a total of 4.34 acres, Parcel 1F (3.77 acres) and Parcel 2F (0.57 acres), located on the southwest part of the airport. This notice announces that the FAA is considering the release of the subject airport property at Southern Illinois Airport, from all federal land covenants. Approval does not constitute a commitment by the FAA to financially assist in disposal of the subject airport property nor a determination that all measures covered by the program are eligible for grant-in-aid funding from the FAA. In accordance with section 47107(h) of Title 49, United States Code, this notice is required to be published in the Federal Register 30 days before modifying the land-use assurance that requires the property to be used for an aeronautical purpose.
Petition for Exemption; Summary of Petition Received
This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Airworthiness Directives; Hawker Beechcraft Corporation Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation Model G58 airplanes. This proposed AD was prompted by notification from Hawker Beechcraft Corporation that certain affected aircraft were produced with the incorrect gauge wiring installed. This proposed AD would require replacement of the incorrect gauge wiring with the correct wiring required by type design and the aircraft's circuit protection. We are proposing this AD to correct the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
We are revising an earlier proposed airworthiness directive (AD) for certain The Boeing Company Model 767 airplanes. That NPRM proposed to require drilling a drain hole in the flanged tubes for certain elevator control cable aft pressure seals; doing repetitive inspections for dirt, loose particles, or blockage of the flanged tube and drain hole for the pressure seals, and corrective action if necessary; replacing the aft air-intake duct assembly with a new or modified assembly and installing a dripshield; and installing gutters on the horizontal stabilizer center section and modifying the side brace fittings. That NPRM was prompted by reports of stiff operation of the elevator pitch control system and jammed elevator controls. This action revises that NPRM by proposing to require replacement of pressure seal assemblies, rather than the proposed drilling of drain holes; revising a certain compliance time and inspection type; adding certain optional actions; and revising the applicability. We are proposing this supplemental NPRM to prevent moisture from collecting and freezing on the elevator control system components, which could limit the ability of the flightcrew to make elevator control inputs and result in reduced controllability of the airplane. Since these actions impose an additional burden over that proposed in the previous NPRM, we are reopening the comment period to allow the public the chance to comment on these proposed changes.
Airworthiness Directives; Hawker Beechcraft Corporation Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation Model C90GTi (King Air) airplanes. This proposed AD was prompted by reports of incorrect gauge wires used in certain wiring bundles for the cockpit electrical power for backlighting and instrument panel components. This proposed AD would require replacing incorrect gauge wires in certain electrical power wiring bundles, inspecting associated wiring bundles and components for heat damage, and taking all necessary corrective actions. We are proposing this AD to correct the unsafe condition on these products.
Agency Information Collection Activities: Requests for Comments; Clearance of a New Approval of Information Collection: FAA Customer Service Surveys
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval for a new information collection. This is a new generic clearance for the purpose of gathering customer satisfaction data directly from customers for a wide variety of services.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Flight Simulation Device Initial and Continuing Qualification and Use
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on May 18, 2012, 77 FR 29748. The collection of this information is necessary to ensure safety of flight by ensuring complete and adequate training, testing, checking, and experience is obtained and maintained by those who conduct flight simulation training.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.