Federal Aviation Administration June 2007 – Federal Register Recent Federal Regulation Documents
Results 101 - 129 of 129
National Air Tour Safety Standards; Correction
The FAA is correcting references in its Commercial Air Tours and National Parks Air Tour Management regulations to conform to amendments made by the National Air Tour Safety Standards final rule published on February 13, 2007 (72 FR 6884). In addition, the FAA is removing a sentence from the preamble that referred to aircraft certificated as ``Experimental Category'' and clarifying the applicability of the rule to the ``Young Eagles'' program.
Area Navigation (RNAV) and Miscellaneous Amendments
The FAA is amending its regulations to reflect technological advances that support area navigation (RNAV); include provisions on the use of suitable RNAV systems for navigation; amend certain terms for consistency with those of the International Civil Aviation Organization (ICAO); remove reference to the middle marker in certain sections because a middle marker is no longer operationally required; clarify airspace terminology; and incorporate by reference obstacle departure procedures into Federal regulations. The changes will facilitate the use of new navigation reference sources, enable advancements in technology, and increase efficiency of the National Airspace System.
Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals
The FAA publishes a monty notice, as appropriate, of PFC approvals and disapprovals under the provisions of the Aviation Safety and Capacity Expansion Act of 1990 (Title IX of the Omnibus Budget Reconciliation Act of 1990) (Pub. L. No. 101-508) and Part 158 of the Federal Aviation Regulations (14 CFR Part 158). This notice is published pursuant to paragraph d of Sec. 158.29.
Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800 and -900 Series Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, -800 and -900 series airplanes. This proposed AD would require inspecting ground blocks GD261 and GD264 for corrosion, measuring the electrical bond resistance between the ground blocks and the airplane structure, separating the ground wires for the fuel boost pump circuit between ground blocks GD261 and GD264, and doing corrective actions if necessary. This proposed AD results from a report of random flashes of the six fuel pump low pressure lights and intermittent operation of the fuel boost pumps. We are proposing this AD to prevent the simultaneous malfunction of all six fuel boost pumps, which could cause the engines to operate on suction feed and potentially flame out.
Airworthiness Directives; Gulfstream Aerospace LP Model Galaxy Airplanes and Model Gulfstream 200 Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Airbus Model A321 Series Airplanes
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; McDonnell Douglas Model 717-200 Airplanes
The FAA is revising an earlier proposed airworthiness directive (AD) for all McDonnell Douglas Model 717-200 airplanes. The original NPRM would have required inspecting the power conversion distribution unit (PCDU) to determine its part number, and modifying certain PCDUs. The original NPRM was prompted by reports of failed PCDUs, the loss of an electrical bus, and the presence of a strong electrical burning odor in the flight deck and forward cabin. This action revises the original NPRM by reidentifying the part number reference for the proposed corrective action. We are proposing this supplemental NPRM to prevent the loss of an electrical bus due to PCDU failure, resulting in the loss of all flight displays for an unacceptable time period, and consequent emergency landing.
Airworthiness Directives; Airbus Model A340-211, -212, -311, and -312 Airplanes
The FAA is superseding an existing airworthiness directive (AD) that applies to certain Airbus Model A340-211, -212, -311, and - 312 airplanes. The existing AD currently requires an initial rotating probe inspection and initial and repetitive ultrasonic inspections for discrepancies of the first fastener hole of the horizontal flange of the keel beam on previously modified airplanes, installation of new fasteners, and corrective action if necessary. This AD retains the actions required by the existing AD and adds new rotating probe inspections and a terminating action for the repetitive inspections of the existing AD. This AD results from a report that certain inspections, done before accomplishing the modification of the lower keel beam fitting and forward lower shell connection, revealed cracking that was outside the modification limits specified in the service bulletin; the cracking was repaired by installing a titanium doubler. We are issuing this AD to prevent discrepancies of the fastener holes of the horizontal flange of the keel beam, which could result in reduced structural integrity of the fuselage.
Airworthiness Directives; General Electric Company (GE) CF6-80C2B Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for GE CF6-80C2B series turbofan engines with electronic control units (ECUs), installed on Boeing 747 and 767 series airplanes. This AD requires installing software version 8.2.Q1 to the engine ECU, which increases the engine's margin to flameout. This AD results from reports of engine flameout events during flight, including reports of events where all engines simultaneously experienced a flameout or other adverse operation. Though the root cause investigation is not yet complete, we believe exposure to ice crystals during flight is associated with these flameout events. We are issuing this AD to provide increased margin to flameout, which will minimize the potential of an all-engine flameout event caused by ice accretion and shedding during flight.
Petition for Exemption; Summary of Petition Received
This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of any petition or its final disposition.
Proposed Modification and Establishment of Restricted Areas and Other Special Use Airspace, Adirondack Airspace Complex; Fort Drum, NY
This action proposes to restructure the restricted areas located in the vicinity of Fort Drum, NY. The Air National Guard (ANG) proposed to redesign the airspace, referred to as the Adirondack Airspace Complex, by making a minor modification to the ceiling of existing restricted area R-5201, and by establishing two new restricted areas: R-5202A and R-5202B. In addition, the ANG proposes to redesign the Military Operations Areas (MOA) associated with the Fort Drum restricted areas. MOAs are not regulatory airspace, but are established administratively. Because the MOAs form an integral part of the Adirondack Airspace Complex, the FAA is also seeking comment on the proposed MOA changes through this NPRM. The ANG proposes these airspace changes to provide additional special use airspace (SUA) needed to conduct high altitude, long-range weapons releases and to allow more realistic training in modern tactics to be conducted in the Adirondack Airspace Complex.
Airworthiness Directives; Boeing Model 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, and 747SP Series Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Boeing Model 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, and 747SP series airplanes. This proposed AD would require reconfiguring the clamps of certain wire bundles and applying insulating sealant to certain fasteners inside the fuel tanks. This proposed AD results from fuel system reviews conducted by the manufacturer. We are proposing this AD to prevent arcing inside the fuel tanks in the event of a lightning strike or high-powered short circuit, which could result in a fuel tank explosion or fire.
Airworthiness Directives; Boeing Model 747-200B, 747-300, 747-400, 747-400D, and 747-400F Series Airplanes Equipped With General Electric CF6-80C2 Engines
The FAA proposes to adopt a new airworthiness directive (AD) for certain Boeing Model 747-200B, 747-300, 747-400, 747-400D, and 747- 400F series airplanes. This proposed AD would require repetitive inspections of the left- and right-hand flipper door assemblies of the engine core cowls for migrated pins and damaged flipper doors, and corrective actions if necessary. Modification of the hinge assemblies terminates the repetitive inspections. This proposed AD results from two reports of missing flipper doors for the engine core cowls. We are proposing this AD to detect and correct migrated hinge pins and damaged flipper doors, which could allow the flipper door to fall off, resulting in the potential for an engine fire to propagate into the flammable leakage zone of the strut and for the amount of fire extinguishing agent reaching the fire to be diluted, and subsequent uncontained fire in the engine strut.
Airworthiness Directives; McDonnell Douglas Model MD-11, MD-11F, DC-10-30 and DC-10-30F (KC-10A and KDC-10), DC-10-40, DC-10-40F, and MD-10-30F Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain McDonnell Douglas Model MD-11, MD-11F, DC-10-30 and DC-10- 30F (KC-10A and KDC-10), DC-10-40, DC-10-40F, and MD-10-30F airplanes. This proposed AD would require measuring the electrical resistance of the bond between the No. 2 fuel transfer pump adapter surface of the fuel tank and the fuel transfer pump housing flange, and performing corrective and other specified actions as applicable. This proposed AD results from a design review of the fuel tank systems. We are proposing this AD to prevent inadequate bonding between the No. 2 fuel transfer pump adapter surface of the fuel tank and the fuel transfer pump housing flange. Inadequate bonding could result in a potential ignition source inside the fuel tank if the fuel transfer pump and structure interface are not submerged in fuel, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800 and -900 Series Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, -800 and -900 series airplanes. This proposed AD would require sealing the fasteners on the front and rear spar inside the main fuel tank and on the lower panel of the center fuel tank, inspecting the wire bundle support installation in the equipment cooling system bays to identify the type of clamp installed and determine whether the Teflon sleeve is installed, and doing related corrective actions if necessary. This proposed AD results from a design review of the fuel tank systems. We are proposing this AD to prevent arcing at certain fuel tank fasteners, in the event of a lightning strike or fault current event, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Airworthiness Directives; General Electric Company CF34-10E Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for General Electric Company (GE) CF34-10E series turbofan engines. This AD requires revising the combustor case published life limit and removing combustor cases from service before reaching a reduced life limit. This AD results from GE's evaluation of the effects to the combustor case due to installing version 5.10 software in the full-authority digital electronic control (FADEC), and revising the combustor case published life limit. We are issuing this AD to prevent uncontained combustor case failure resulting in an in-flight engine shutdown and possible damage to the airplane.
Airworthiness Directives; Bombardier Model DHC-8-400 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400 series airplanes. This AD requires revising the Limitations section of the airplane flight manual to include procedures for pulling the ``HYD PWR XFER'' circuit breaker in the event of the loss of all hydraulic fluid in the No. 1 or No. 2 hydraulic system. This AD results from reports of fluid loss in the No. 2 hydraulic system, causing the power transfer unit to overspeed, increasing the fluid flow within the No. 1 hydraulic system. We are issuing this AD to prevent possible loss of both the No. 1 and No. 2 hydraulic systems, resulting in the potential loss of several functions essential for safe flight and landing of the airplane.
Airworthiness Directives; Airbus Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes)
The FAA is superseding an existing airworthiness directive (AD) that applies to all Airbus Model A300-600 series airplanes. That AD currently requires inspections of the lower door surrounding structure to detect cracks and corrosion; inspections to detect cracking of the holes of the corner doublers, the fail-safe ring, and the door frames of the door structures; and repair if necessary. That AD also provides for optional terminating action for certain inspections. This new AD retains all requirements of the existing AD, mandates the previously optional terminating action, reduces the applicability of the existing AD, and adds repetitive inspections behind scuff plates for certain affected airplanes. This AD results from a determination that further rulemaking is necessary to improve the fatigue behavior of the cabin door surroundings. We are issuing this AD to prevent corrosion between the scuff plates at exit and cargo doors and fatigue cracks originating from certain fastener holes located in adjacent structure, which could result in reduced structural integrity of the door surroundings.
Airworthiness Directives; Bombardier Model DHC-8-100, DHC-8-200, and DHC-8-300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-100, DHC-8-200, and DHC-8-300 series airplanes. This AD requires, for certain airplanes, modification of the upper bearing of the main landing gear (MLG) shock strut. This AD also requires, for certain airplanes, revising the de Havilland DHC-8 Maintenance Program Manual to include the MLG shock strut servicing task. This AD results from reports of over-extension of the MLG shock strut piston, which allows the torque links to go over-center and rest on the piston. We are issuing this AD to prevent loss in shock absorption during touchdown and failure of the shock strut housing, which could result in a subsequent loss of directional control.
Airworthiness Directives; McDonnell Douglas Model DC-8-33, -42, and -43 Airplanes; Model DC-8-50 Series Airplanes; Model DC-8F-54 and -55 Airplanes; Model DC-8-60 Series Airplanes; Model DC-8-60F Series Airplanes; Model DC-8-72 Airplanes; and Model DC-8-70F Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas airplanes described previously. This AD requires installing bonding jumpers to the airplane wing structure from the fuel system in-line electrical solenoid valves along the left and right wing front spar. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent point- of-contact arcing or filament heating damage in the fuel lines that could create a potential ignition source, which, in combination with flammable fuel vapors, could cause a fuel tank explosion and consequent loss of the airplane.
Airworthiness Directives; General Electric Company (GE) CF6-80 Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for GE CF6-80 series turbofan engines with fuel shroud retaining rings, part number (P/N) J204P0084, installed. This AD requires replacing those retaining rings with a more robust design fuel shroud retaining snap ring. This AD results from two events of external engine fuel leakage and a subsequent under-cowl engine fire. We are issuing this AD to prevent an under-cowl engine fire and damage to the airplane during an engine high vibration event.
Airworthiness Directives; Diamond Aircraft Industries GmbH Model DA 40 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Change in Extinguishing Agent Container Requirements
On April 20, 2007, the FAA published in the Federal Register a direct final rule entitled Change in Extinguishing Agent Container Requirements. The rule aligned the operational and certification requirements regarding airplane extinguishing agent containers or fire bottles; and it removed an obsolete section reference from part 135. This action withdraws the rule because the FAA received several adverse comments.
Proposed Revision of Class E Airspace; Hailey, ID
This action proposes to revise Class E airspace at Hailey, ID. Additional controlled airspace is necessary to accommodate aircraft using a new Area Navigation (RNAV) Required Navigational Performance (RNP) Instrument Approach Procedure (IAP) at Friedman Memorial Airport. The FAA is proposing this action to enhance the safety and management of Instrument Flight Rules (IFR) aircraft operations at Friedman Memorial Airport, Hailey, ID.
Proposed Revision of Class E Airspace; Hoquiam, WA
This action proposes to revise Class E airspace at Hoquiam, WA. Additional controlled airspace is necessary to accommodate aircraft using the Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedure (SIAP) at Bowerman Airport. The FAA is proposing this action to enhance the safety and management of Instrument Flight Rules (IFR) aircraft operations at Bowerman Airport, Hoquiam, WA.
Proposed Establishment of Class E Airspace; Everett, WA
This action proposes to establish Class E surface airspace at Everett, WA. Controlled airspace is necessary to accommodate aircraft executing Special Visual Flight Rules (SVFR) operations at Everett, Snohomish County Airport (Paine Field), Everett, WA.
Airworthiness Directives; Cessna Model 500, 501, 550, 551, S550, 560, 560XL, and 750 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Cessna Model 500, 550, S550, 560, 560XL, and 750 airplanes. That AD currently requires installing identification sleeves on the wires for the positive and negative terminal studs of the engine and/or auxiliary power unit (APU) fire extinguishing bottles, as applicable, and re-connecting the wires to the correct terminal studs. This new AD retains the requirements of the existing AD; adds airplanes to the applicability; and, for certain airplanes only, requires a review of wiring changes made using the original issue of one service bulletin and corrective actions if necessary. This AD results from a determination that additional airplanes are subject to the unsafe condition described in the existing AD. We are issuing this AD to ensure that the fire extinguishing bottles are activated in the event of an engine or APU fire, and that flammable fluids are not supplied during a fire, which could result in an unextinguished fire in the nacelle or APU.
Notice of Intent To Request Approval From the Office of Management and Budget of a New Information Collection Activity, Request for Comments; New England Region Aviation Expo
The FAA invites public comments about our intention to request the Office of Management and Budget (OMB) to approve a new information collection. The information is being used to properly identify airmen to allow the agency to verify their foreign license being used to qualify for a US certificate.
Agency Information Collection Activity Seeking OMB Approval
The FAA invites public comments about our intention to request the Office of Management and Budget's (OMB) revision of a current information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on March 23, 2007, vol. 72, no. 52, page 13855. Title 49 U.S.C. 44703(h) mandates that all U.S. air carriers operating under 14 CFR parts 121 or 135, and all U.S. air operators under 14 CFR part 125, and certain others, request and receive certain training, safety, and testing records before extending a firm offer of employment to an individual who is applying to their company as a pilot.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.