Department of Transportation December 22, 2022 – Federal Register Recent Federal Regulation Documents
Results 1 - 17 of 17
Airworthiness Directives; Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350-1041 airplanes. This AD was prompted by a report of a computer software error leading to the rudder oscillatory failure case not being calculated properly. This AD requires updating certain computer software, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A310 series airplanes. This AD was prompted by a determination that new or more restrictive maintenance requirements and airworthiness tasks are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness tasks, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A310 series airplanes. This AD was prompted by a determination that new or more restrictive maintenance requirements and airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350-941 and A350-1041 airplanes. This AD was prompted by a report that Heavy Expanded Copper Foil (HECF) patches may not have been installed at all required locations of the upper and lower wing covers. This AD requires a one-time detailed inspection of the affected areas and, depending on findings, accomplishment of applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Embraer S.A. (Type Certificate Previously Held by Yaborã Indústria Aeronáutica S.A.; Embraer S.A.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Embraer S.A. Model ERJ 190-300 and -400 airplanes. This AD was prompted by reports of friction marks on the engine fire extinguishing system tube, in the region of the aft fairing of the left-hand (LH) pylon. This AD requires rework of the retainer of the LH pylon access panel, inspection and replacement, as applicable, of the LH engine fire extinguishing system tube, and installation of a support, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; GE Aviation Czech s.r.o. (Type Certificate Previously Held by WALTER Engines a.s., Walter a.s., and MOTORLET a.s.) Turboprop Engines
The FAA is adopting a new airworthiness directive (AD) for certain GE Aviation Czech s.r.o. (GEAC) M601D-11, M601E-11, M601E-11A, M601E-11AS, M601E-11S, M601F, H75-100, H75-200, H80, H80-100, H80-200, H85-100, and H85-200 model turboprop engines. This AD was prompted by reports of cracks in dilution tube weld areas of the combustion chamber outer liner. This AD requires initial and repetitive borescope inspections (BSIs) of the dilution tube weld areas of the combustion chamber outer liner and, depending on the results of the inspections, replacement of the combustion chamber outer liner with a part eligible for installation. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
The FAA proposes to supersede Airworthiness Directive (AD) 2020-21-07, which applies to all Airbus SAS Model A350-941 and -1041 airplanes. AD 2020-21-07 requires replacement of affected passenger oxygen masks (which includes re-identifying the parts). Since the FAA issued AD 2020-21-07, it was determined that additional parts are subject to the unsafe condition. This proposed AD would continue to require the actions in AD 2020-21-07, and would require replacing additional affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). This proposed AD would also prohibit installation of affected parts. The FAA is proposing this AD to address the unsafe condition on these products.
Entry-Level Driver Training: SBL Truck Driving Academy, Inc.; Application for Exemption
FMCSA announces its decision to deny the exemption application from SBL Truck Driving Academy, Inc. (SBL). SBL sought an exemption from the theory and behind-the-wheel (BTW) instructor requirements contained in the entry-level driver training (ELDT) regulations for two of its instructors. SBL specifically requested an exemption from the requirement that instructors have at least two years of experience driving a commercial motor vehicle (CMV) requiring a commercial driver's license (CDL) of the same or higher class and/or the same endorsement level for which training is to be provided. FMCSA analyzed the exemption application and public comments and determined that the application lacked evidence that would ensure an equivalent or greater level of safety than would be achieved absent such exemption.
Incorporation by Reference; North American Standard Out-of-Service Criteria; Hazardous Materials Safety Permits
FMCSA amends its Hazardous Materials Safety Permits regulations to incorporate by reference the April 1, 2022, edition of the Commercial Vehicle Safety Alliance's (CVSA) handbook (the handbook) containing inspection procedures and Out-of-Service Criteria (OOSC) for the inspection of commercial motor vehicles used in the transportation of transuranic waste and highway route-controlled quantities of radioactive material. The OOSC provide enforcement personnel nationwide, including FMCSA's State partners, with uniform enforcement tolerances for these inspections. Through this rule, FMCSA incorporates by reference the April 1, 2022, edition of the handbook.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This AD was prompted by a report indicating that a crack was found in one of the holes of the wing rear spar lower chord at the main landing gear (MLG) aft fitting at a certain wing buttock line (WBL). This AD requires repetitive open hole high frequency eddy current (HFEC) inspections or surface HFEC and ultrasonic (UT) inspections for cracking of the wing rear spar lower chord at the MLG aft fitting at a certain WBL, and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
Proposed Establishment of Class E Airspace; Paoli, IN
This action proposes to establish Class E airspace at Paoli, IN. The FAA is proposing this action to support new public instrument procedures.
Proposed Establishment of Class E Airspace; Marion, IA
This action proposes to establish Class E airspace at Marion, IA. The FAA is proposing this action to support new public instrument procedures.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is superseding Airworthiness Directive (AD) 2021-14- 20, which applied to all The Boeing Company Model 737 airplanes. AD 2021-14-20 required repetitive functional tests of the cabin altitude pressure switches, and on-condition actions, including replacement, if necessary. AD 2021-14-20 also required reporting test results. This AD was prompted by data collected from the reports required by AD 2021-14- 20, which revealed that the switches were subject to false test failures due to lack of clear instructions for setup of the test adapters during the functional tests. This AD retains the repetitive functional tests and on-condition actions, and specifies certain adapter requirements for the functional tests. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is superseding Airworthiness Directive (AD) 2017-18- 05, which applied to all The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. AD 2017-18-05 required repetitive replacement or inspection of certain fuse pins, and applicable on-condition actions. This AD was prompted by a report of damage found at the lower trailing edge panels of the left wing and a broken fuse pin of the landing gear beam end fitting. This AD was further prompted by the need for new inspections for cracking of the fuse pin, and the determination that additional airplanes are subject to the unsafe condition. This AD continues to require the actions in AD 2017-18-05 and also requires repetitive replacement of certain fuse pins, repetitive inspections for cracking of the fuse pin, and applicable on-condition actions. This AD also revises the applicability by adding airplanes. The FAA is issuing this AD to address the unsafe condition on these products.
Entry-Level Driver Training: Western Area Career and Technology Center; Application for Exemption
FMCSA announces its decision to deny the exemption application from Western Area Career and Technology Center (WACTC). WACTC requested an exemption from the theory and behind-the-wheel (BTW) instructor requirements contained in the entry-level driver training (ELDT) regulations for one prospective instructor. FMCSA analyzed the exemption application and public comments and determined that the application lacked evidence that would ensure a level of safety equivalent to or greater than would be achieved absent such exemption.
Final Re-Designation of the Primary Highway Freight System (PHFS)
This notice announces the re-designated PHFS to meet the statutory requirements of the authorizing law. This notice presents a final, re-designated PHFS, provides summary analysis of input received for PHFS re-designation, FHWA responses to comments, the methodology applied, and changes made for the re-designation of the PHFS.
Airworthiness Directives; General Electric Company Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) GEnx-1B and GEnx-2B model turbofan engines. This AD was prompted by a manufacturer investigation that revealed that certain high-pressure turbine (HPT) stage 2 disks, forward seals, and stages 6-10 compressor rotor spools were manufactured from powder metal material suspected to contain iron inclusion. This AD requires replacement of the affected HPT stage 2 disks, forward seals, and stages 6-10 compressor rotor spools. The FAA is issuing this AD to address the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
