Department of Transportation May 15, 2018 – Federal Register Recent Federal Regulation Documents

We are adopting a new airworthiness directive (AD) for certain Airbus Model A318 series airplanes and Model A319 series airplanes; all Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes; and all Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. This AD was prompted by an evaluation by the design approval holder (DAH) indicating that the holes of the upper cleat to upper stringer attachments at certain areas of the left- and right-hand wings are subject to widespread fatigue damage (WFD). This AD requires modifying the holes of the upper cleat to upper stringer attachments at certain areas of the left- and right-hand wings. We are issuing this AD to address the unsafe condition on these products.

We propose to adopt a new airworthiness directive (AD) for certain Airbus Model A319-115 and -132 airplanes, and Model A320-214, - 216, -232, and -233 airplanes. This proposed AD was prompted by a report indicating that certain modified airplanes do not have electrical ground wires on the fuel level sensing control unit (FLSCU), which adversely affects the fuel gravity feeding operation. This proposed AD would require modification of the FLSCU wiring. We are proposing this AD to address the unsafe condition on these products.

This notice announces the public meeting via conference call of the Saint Lawrence Seaway Development Corporation Advisory Board.

We propose to supersede Airworthiness Directive (AD) 2017-16- 05, which applies to certain The Boeing Company Model 737-600, -700, - 700C, -800, -900, and -900ER series airplanes. AD 2017-16-05 requires a one-time detailed visual inspection for discrepancies in the Krueger flap bullnose attachment hardware, and related investigative and corrective actions if necessary. Since we issued AD 2017-16-05, we received a report of a missing no. 2 Krueger flap bullnose hinge bolt from an airplane that was not included in the applicability of AD 2017- 16-05. This proposed AD would add airplanes and an additional inspection to determine if any Krueger flap no. 1, 2, 3, or 4 has been replaced, and related investigative and corrective actions. Since this is a rotable parts issue, the applicability of this AD has been expanded beyond the airplanes listed in the related service bulletin to include all airplanes on which a Krueger flap bullnose may be installed. We are proposing this AD to address the unsafe condition on these products.

We propose to supersede Airworthiness Directive (AD) 2016-13- 16, which applies to all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. AD 2016-13-16 requires an inspection or records check to determine if affected horizontal stabilizers are installed, related investigative actions, and, for affected horizontal stabilizers, repetitive inspections for any crack of the horizontal stabilizer rear spar upper chord, and corrective action if necessary. Since we issued AD 2016-13-16, we have determined that clarification of inspection areas and serial number information of the horizontal stabilizer is necessary. Therefore, this proposed AD would retain the requirements of AD 2016-13-16, with revised service information that clarifies the inspection areas and serial number information of the horizontal stabilizer. We are proposing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for certain Pacific Aerospace Limited Model 750XL airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as abrasion damage to the wing leading edge that could result in a fuel leak. We are issuing this AD to require actions to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This AD was prompted by reports indicating additional cracking in the inspar upper skin at wing buttock line (WBL) 157 and in the skin at two holes common to the rear spar in the same area, and rear spar web cracks were also noted on both wings. Subsequent inspections revealed that the right rear spar upper chord was almost completely severed and the left rear spar upper chord was completely severed. Additional reports identified cracking in the main landing gear (MLG) beam forward support fitting. This AD requires the installation of standard-size fasteners for a certain configuration and inspections for any crack in certain locations of the rear spar. We are issuing this AD to address the unsafe condition on these products.