Department of Transportation January 2016 – Federal Register Recent Federal Regulation Documents

We are adopting a new airworthiness directive (AD) for Airbus Helicopters Deutschland GmbH (AHD) (previously Eurocopter Deutschland GmbH) Model MBB-BK 117 A-1, A-3, A-4, B-1, B-2, C-1, and C-2 helicopters. This AD requires an initial and recurring inspection of the N2 control arm and, depending on the outcome of the inspection, repairing or replacing the N2 control arm. This AD was prompted by a report of a heavily corroded and broken N2 control arm. The actions of this AD are intended to detect corrosion, a crack, or a scratch in the N2 control arm, which could lead to failure of the N2 control arm, a drop in rotor speed, and subsequent loss of control of the helicopter.

We are superseding Airworthiness Directive (AD) 2002-23-20, for certain Dassault Aviation Model FALCON 900EX and MYSTERE-FALCON 900 airplanes. AD 2002-23-20 required repetitive operational tests of the flap asymmetry detection system to verify proper functioning, and repair if necessary; repetitive replacement of the inboard flap jackscrews with new or reconditioned jackscrews; and repetitive measurement of the screw/nut play of the jackscrews on the inboard and outboard flaps to detect discrepancies, and corrective action if necessary. AD 2002-23-20 also required a revision of the airplane flight manual. Since we issued AD 2002-23-20, the maintenance manual has been revised. This AD requires revising the maintenance or inspection program, as applicable, to include the maintenance tasks and airworthiness limitations specified in the Airworthiness Limitations section of the airplane maintenance manual. This AD also removes the Model FALCON 900EX airplanes from the applicability. We are issuing this AD to prevent reduced structural integrity of the airplane.

We are adopting a new airworthiness directive (AD) for all Airbus Model A310 and Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes; and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). This AD was prompted by a report of skin disbonding and damage found on the composite side panel of the rudder, located between the rudder core and skin of a previously repaired area. This AD requires an inspection for disbonding or damage of certain rudders, and related investigative actions and corrective actions if necessary. We are issuing this AD to detect and correct disbonding and damage of the rudder, which could result in reduced structural integrity of the rudder and consequent reduced controllability of the airplane.

We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by reports of fluid entry and accumulation in the aft equipment bay. This AD requires modifying the aft equipment bay. We are issuing this AD to prevent excessive quantities of flammable fluid accumulation in the aft equipment bay. Flammable fluid entry and accumulation in the aft equipment bay, in excessive quantities, could exceed safe levels maintained by the drainage and ventilation system.

This notice contains a summary of a petition seeking relief from specified requirements of Title 14 of the Code of Federal Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. Aeronautical information is required by the FAA in order to carry out agency missions such as those related to aviation flying safety, flight planning, airport engineering and federal grants analysis, aeronautical chart and flight information publications, and the promotion of air commerce as required by statute.

We propose to adopt a new airworthiness directive (AD) for all Fokker Services B.V. Model F.28 Mark 1000, 2000, 3000, and 4000 airplanes. This proposed AD was prompted by a design review, that revealed a hot spot may develop in the main fuel tank under certain failure conditions of the solenoid of the level control pilot valve, the reed switch of the main tank overflow valve, the level float switch of the collector tank, or the solenoid of the main tank fueling shut- off valve. This proposed AD would require installing fuses in the wiring of the solenoid of the level control pilot valve, the reed switch of the main tank overflow valve, the level float switch of the collector tank, and the solenoid of the main tank fueling shut-off valve, as applicable. This proposed AD would also require accomplishing concurrent actions and revising the airplane maintenance or inspection program, as applicable, by incorporating fuel airworthiness limitation items and critical design configuration control limitations (CDCCLs). We are proposing this AD to prevent an ignition source in the main fuel tank vapor space, which could result in a fuel tank explosion and consequent loss of the airplane.

We propose to supersede Airworthiness Directive (AD) 2010-23- 19, that applies to certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, and 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, and Model CL-600-2D24 (Regional Jet Series 900) airplanes. AD 2010-23-19 requires repetitive inspections for damage of the main landing gear (MLG) inboard doors and fairing, and corrective actions if necessary. Since we issued AD 2010- 23-19, we have received reports of the MLG failing to fully extend. This proposed AD would require repetitive inspections for damage of the MLG inboard doors, MLG fairing, and adjacent structures of the MLG inboard doors, and corrective actions if necessary; replacement of the MLG fairing seal; and a terminating action involving increasing the clearances between the MLG fairing and MLG door. This proposed AD would also add one airplane and remove others from the applicability. We are proposing this AD to prevent loss of controllability of the airplane during landing.

We propose to adopt a new airworthiness directive (AD) for all Fokker Services B.V. Model F.28 Mark 1000, 2000, 3000, and 4000 airplanes. This proposed AD was prompted by a design review that revealed insufficient measures were taken to ensure the correct locking of the attachments of the fuel quantity tank units (FQTUs) in each wing tank. When an FQTU becomes loose, this could lead to insufficient clearance between the FQTU and the adjacent tank structure or other metal parts, and under certain conditions, create an ignition source inside the wing fuel vapor space. This proposed AD would require modifying the FQTUs by applying sealant to cover the nuts, washers, and stud ends at the FQTU attachments in each main wing tank. This proposed AD would also require revising the maintenance or inspection program, as applicable, by incorporating a fuel airworthiness limitation item and a critical design configuration control limitation (CDCCL). We are proposing this AD to prevent an ignition source in the wing fuel tank vapor space, which could result in a wing fuel tank explosion and consequent loss of the airplane.

We propose to supersede Airworthiness Directive (AD) 95-21-09, for all Airbus Model A300 series airplanes, and Airbus Model A300 B4- 600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). AD 95-21-09 currently requires repetitive inspections for cracking of the No. 2 flap beams, and replacement of the flap beams, if necessary; and provides optional modifications for extending certain inspection thresholds, and an optional terminating modification for certain inspections. Since we issued AD 95-21-09, we have determined that the compliance times must be reduced. This proposed AD would reduce the compliance times for inspections and also reduce the number of airplanes affected. We are proposing this AD to detect and correct cracking of the No. 2 flap beams, which could result in rupture of the flap beams and reduced structural integrity of the airplane.

We propose to supersede Airworthiness Directive (AD) 2007-21- 14 R1, for all Airbus Model A310 series airplanes. AD 2007-21-14 R1 currently requires revising the Airworthiness Limitations Section of the Instructions for Continued Airworthiness to incorporate new limitations for fuel tank systems. Since we issued AD 2007-21-14R1, we have determined that more restrictive maintenance requirements and/or airworthiness limitations are necessary. This proposed AD would require revising the maintenance program or inspection program to incorporate revised fuel maintenance and inspection tasks. We are proposing this AD to prevent the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors caused by latent failures, alterations, repairs, or maintenance actions, could result in fuel tank explosions and consequent loss of the airplane.

This action modifies VOR Federal airway V-443, which extends across the United States/Canadian border, in the north central United States. The FAA is taking this action to reflect and accommodate route changes made in Canadian airspace as part of Canada's Windsor-Toronto- Montreal (WTM) airspace redesign project.

PHMSA is issuing this advisory bulletin to remind all owners and operators of gas and hazardous liquid pipelines of the potential for damage to pipeline facilities caused by severe flooding and actions that operators should consider taking to ensure the integrity of pipelines in the event of flooding, river scour, and river channel migration.

This notice contains a summary of a petition seeking relief from specified requirements of Title 14 of the Code of Federal Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

This notice contains a summary of a petition seeking relief from specified requirements of Title 14 of the Code of Federal Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

We propose to adopt a new airworthiness directive (AD) for all Bombardier, Inc. Model DHC-8-400 series airplanes. This proposed AD was prompted by a revision by the manufacturer to the Certification Maintenance Requirements (CMR) of the Airworthiness Limitation Items (ALI), in the Maintenance Requirement Manual (MRM), that introduces a new CMR task that requires repetitive operational checks of the propeller overspeed governor. This proposed AD would require revising the airplane maintenance program or inspection program, as applicable, to incorporate a new CMR task. We are proposing this AD to prevent dormant failure of the propeller overspeed governor, which may lead to a loss of propeller overspeed protection and result in high propeller drag in-flight.

On October 5, 2015, in accordance with the Paperwork Reduction Act of 1995, PHMSA published a notice in the Federal Register (80 FR 60242) inviting comments on information collections titled ``Pipeline Integrity Management in High Consequence Areas Gas Transmission Pipeline Operators; Control Room Management/Human Factors; Integrity Management Program for Gas Distribution Pipelines, and Response Plans for Onshore Oil Pipelines,'' identified by Office of Management and Budget (OMB) control numbers 2137-0610, 2137-0624, 2137- 0625, and 2137-0589. These information collections will expire on March 31, 2016. PHMSA will request an extension with no change for the information collections 2137-0610, 0624, and 0625. PHMSA will request a renewal with revisions to the information collection 2137-0589 to revise the number of respondents PHMSA expected to comply with this information collection. During the 60-day comment period, PHMSA received no comments in response to these collections. PHMSA is publishing this notice to provide the public with an additional 30 days to comment on the renewal of these information collections and announce that these information collections will be submitted to OMB for approval.

We are revising an earlier proposed airworthiness directive (AD) for certain B/E Aerospace protective breathing equipment (PBE) that is installed on airplanes. The NPRM proposed inspecting the PBE to determine if the pouch has the proper vacuum seal and replacing if necessary. The NPRM was prompted by reports of a compromise in the vacuum seal of the pouch that contains the PBE. This action revises the NPRM by requiring replacement of the PBE following newly issued service information regardless of inspection results. We are proposing this supplemental NPRM (SNPRM) to correct the unsafe condition on these products. Since these actions impose an additional burden over that proposed in the NPRM, we are reopening the comment period to allow the public the chance to comment on these proposed changes.

This action amends the city designation of the Class D airspace at Broomfield, CO, changing the designation to Denver, CO, and the airport name to Rocky Mountain Metropolitan Airport. The name and associated city location of the airport are updated to coincide with the FAA's aeronautical database. This does not affect the charted boundaries or operating requirements of the airspace.

FMCSA announces its denial of 100 applications from individuals who requested an exemption from the Federal vision standard applicable to interstate truck and bus drivers and the reasons for the denials. FMCSA has statutory authority to exempt individuals from the vision requirement if the exemptions granted will not compromise safety. The Agency has concluded that granting these exemptions does not provide a level of safety that will be equivalent to, or greater than, the level of safety maintained without the exemptions for these commercial motor vehicle (CMV) drivers.

FMCSA announces receipt of applications from 40 individuals for exemption from the prohibition against persons with insulin-treated diabetes mellitus (ITDM) operating commercial motor vehicles (CMVs) in interstate commerce. If granted, the exemptions would enable these individuals with ITDM to operate CMVs in interstate commerce.

The FAA is issuing this notice to advise the public of the Twenty-Fifth RTCA Special Committee 217 meeting.

Pursuant to Section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463, 5 U.S.C. App. 2), notice is hereby given of a teleconference of the Commercial Space Transportation Advisory Committee (COMSTAC). The Teleconference will take place on Wednesday, January 27, 2016 starting at 3:00 p.m. Eastern Standard Time and will last approximately one hour. The agenda and call-in number will be posted at least one week in advance at https://www.faa.gov/go/ ast. The purpose of this teleconference is to review the International Space Policy Working Group findings and recommendations regarding a potential modification of current U.S. policy on the launching of U.S. technology on Indian launch vehicles. Interested members of the public may submit relevant written statements for the COMSTAC members to consider under the advisory process. Statements may concern the issues and agenda items mentioned above and/or additional issues that may be relevant for the U.S. commercial space transportation industry. Interested parties wishing to submit written statements should contact Michael Beavin, COMSTAC Executive Director, (the Contact Person listed below) in writing (mail or email) by January 22, 2016, so that the information can be made available to COMSTAC members for their review and consideration before the January 27 teleconference. Written statements should be supplied in the following formats: One hard copy with original signature and/or one electronic copy via email. An agenda will be posted on the FAA Web site at www.faa.gov/go/ast. Individuals who plan to participate and need special assistance should inform the Contact Persons listed below in advance of the meeting.

Graco Children's Products, Inc., (Graco) has determined that certain Graco child restraints do not fully comply with paragraph S5.5.2(g)(1)(iii) of Federal Motor Vehicle Safety Standard (FMVSS) No. 213, Child Restraint Systems. Graco filed a report dated March 13, 2015, pursuant to 49 CFR part 573, Defect and Noncompliance Responsibility and Reports. Graco then submitted a petition for an exemption from the notification and remedy requirements of 49 U.S.C. Chapter 301 on the basis that this noncompliance is inconsequential to motor vehicle safety.