Department of Transportation October 31, 2013 – Federal Register Recent Federal Regulation Documents

The Federal Railroad Administration (FRA) hereby gives notice that it has submitted the following information collection request (ICR) to the Office of Management and Budget (OMB) for Emergency Processing under the Paperwork Reduction Act of 1995 (Pub. L. 104-13, 44 U.S.C. 3501 et seq.). FRA requests that OMB authorize the collection of information identified below on or before November 6, 2013, for 180 days after the date of approval by OMB. A copy of this ICR, with applicable supporting documentation, may be obtained by calling FRA's Clearance Officer, Mr. Robert Brogan (tel. (202) 493-6292). These numbers are not toll-free. A copy of this ICR may also be obtained electronically by contacting Mr. Brogan at robert.brogan@dot.gov. Comments and questions about the ICR identified below should be directed to the Office of Information and Regulatory Affairs (OIRA), Attn: FRA OMB Desk Officer, 725 17th St. NW., Washington, DC 20503. Comments and questions about the ICR identified below may also be transmitted electronically to OIRA at oira_submissions@omb.eop.gov.

This action proposes to establish Class E airspace at Eagle Airport, Eagle, AK. Controlled airspace is necessary to accommodate the new Area Navigation (RNAV) Global Positioning System (GPS) standard instrument approach procedures developed for the airport. The FAA is proposing this action to enhance the safety and management of aircraft operations at Eagle Airport, Eagle, AK.

This action proposes to establish Class E airspace at Brevig Mission Airport, Brevig Mission, AK. Controlled airspace is necessary to accommodate aircraft using new Area Navigation (RNAV) Global Positioning System (GPS) standard instrument approach procedures at the airport. The FAA is proposing this action to enhance the safety and management of aircraft operations at the airport.

In compliance with the Paperwork Reduction Act of 1995, this notice announces that the Information Collection Request (ICR) abstracted below will be forwarded to the Office of Management and Budget (OMB) for review and comment. The ICR describes the nature of the information collection and its expected burden. The Federal Register notice with a 60-day comment period soliciting comments on the following collections of information was published on August 13, 2013.

FHWA, as lead agency, is issuing this notice to advise the public that an Environmental Impact Statement (EIS) will be prepared for the proposed project to provide a modern rail crossing at the location of the existing Portageville Bridge (also known as the ``Portage High Bridge'') over the Genesee River in Wyoming and Livingston Counties, New York.

The FAA proposes to rule and invites public comment on the release of land at the Kearney Regional Airport, Kearney, Nebraska, under the provisions of 49 U.S.C. 47107(h)(2).

These special conditions are issued for the Learjet Model 45 series airplanes. These airplanes will have a novel or unusual design feature associated with the architecture and connectivity capabilities of the airplanes' computer systems and networks. Connectivity to, or access by, external systems and networks may result in security vulnerabilities to the airplanes' systems. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

This action proposes special conditions for the Learjet Model LJ-200-1A10 airplane. This airplane will have novel or unusual design features when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. These features are associated with a hybrid construction that uses both composite and metallic materials in the structure for which the crashworthiness responses for occupant safety may not be equivalent to current all-metallic airplanes. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for the crashworthiness of this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

PHMSA published an Advisory Bulletin in the Federal Register on July 18, 2013, (78 FR 42889) reminding owners and operators of liquefied petroleum gas (LPG) and utility liquefied petroleum gas (Utility LP-Gas) plants of their obligation to follow certain sections of Part 192 in addition to the American National Standards Institute/ National Fire Protection Association (ANSI/NFPA) standards 58 or 59. This document supersedes the July 18, 2013, Advisory Bulletin by correcting a typographical error in the sixth bullet and removing the exemption for small utility LP gas systems from Subpart N (Qualification of Pipeline Personnel) from the bulleted list.

This action re-opens the comment period for the notice of draft Order 1050.1F, Environmental Impacts: Policies and Procedures that was published on August 14, 2013. Airports Council International North America (ACI-NA), which represents local, regional and state governing bodies that own and operate commercial airports across the United States, requested that the FAA extend the comment period for 14 days.

This action proposes special conditions for the Bombardier Inc. Model BD-500-1A10 and BD-500-1A11 series airplanes. These airplanes will have a novel or unusual design feature associated with the materials used to fabricate the fuselage, which may affect fire propagation during an in-flight fire. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

We are adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ series airplanes. This AD was prompted by a report of a cracked pick-up bracket of the forward outboard pylon of the number 1 engine due to stress corrosion. This AD requires repetitive inspections and, depending on findings, repair of the pylon pick-up brackets. We are issuing this AD to detect and correct cracking of the pick-up bracket, which could result in the engine pylon separating from the wing, with consequent damage to the airplane and reduced controllability.

We are adopting a new airworthiness directive (AD) for Eurocopter Deutschland GmbH (Eurocopter) Model EC135 P1, P2, P2+, T1, T2, and T2+ helicopters. This AD requires inspecting each linear transducer bearing (bearing) for freedom of movement and replacing the bearing if there is binding or rough turning or if there is chafing or damage on the lower side of the floor. Also, this AD requires modifying and re-identifying a certain rod. This AD was prompted by an incident involving limited control of a tail rotor because of the binding of a bearing. The actions of this AD are intended to detect and replace each bearing subject to binding, which could lead to subsequent loss of control of the helicopter.

We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-400 series airplanes. This AD was prompted by reports of fasteners missing on an airplane undergoing a passenger- to-freighter conversion. This AD requires doing a general visual inspection of the station 1920 splice clip for correct fastener installation, and related investigative and corrective actions if necessary. We are issuing this AD to detect and correct missing or incorrect fasteners, which can lead to cracking and loss of load carrying capacity, resulting in a possible decompression event.

We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604 Variants) airplanes. This AD was prompted by reports of airspeed mismatch between the pilot and co-pilot's airspeed indicators, which occurred during or after heavy rain. This AD requires, for certain airplanes, inspecting for drain bottles having certain part numbers, and replacing affected drain bottles. This AD requires, for certain other airplanes, replacing drain bottles. We are issuing this AD to prevent pitot static tubing from becoming blocked by water, which if not corrected, could lead to erroneous airspeed and altitude indications, and consequent loss of control of the airplane.

We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 727 airplanes. This AD was prompted by reports indicating that a standard fuel tank access door was located where an impact-resistant access door was required, and stencils were missing from some impact-resistant access doors. This AD requires an inspection of the left- and right-hand wing fuel tank access doors to determine that impact-resistant access doors are installed in the correct locations, and to replace any door with an impact-resistant access door if necessary. This AD also requires an inspection for stencils and index markers on impact-resistant access doors, and application of new stencils or index markers if necessary. This AD also requires revising the maintenance program to incorporate changes to the airworthiness limitations section. We are issuing this AD to prevent foreign object penetration of the fuel tank, which could cause a fuel leak near an ignition source (e.g., hot brakes), consequently leading to a fuel-fed fire.

We are superseding Airworthiness Directive (AD) 97-19-10 for Sikorsky Aircraft Corporation-manufactured Model S-64E helicopters (type certificate currently held by Erickson Air-Crane Incorporated (Erickson)). AD 97-19-10 required inspecting and reworking the main gearbox (MGB) assembly second stage lower planetary plate (plate). This action establishes or reduces the life limits for certain flight- critical components, removes from service various parts, requires repetitive inspections and other corrective actions, and requires replacing any cracked part discovered during an inspection. This AD is prompted by further analysis performed by the current type certificate holder and the service history of certain parts. The actions specified in this AD are intended to prevent a crack in a flight critical component, failure of a critical part, and subsequent loss of control of the helicopter.

We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 727 airplanes. This AD was prompted by certain mandated programs intended to support the airplane reaching its limit of validity (LOV) of the engineering data that support the established structural maintenance program. This AD requires, for certain airplanes, a modification of the web of the horizontal stabilizer center section rear spar. For the other airplanes, this AD requires an inspection for cracks in the web, and repair or modification as applicable. We are issuing this AD to prevent cracking at the upper fastener holes in the riveted web in the horizontal stabilizer center section rear spar, which could result in failure of the spar forging and lead to horizontal stabilizer separation and loss of control of the airplane.

We are superseding Airworthiness Directive (AD) 2003-08-51 for MD Helicopters, Inc. (MDHI), Model 369A, 369D, 369E, 369H, 369HE, 369HM, 369HS, 369F and 369FF helicopters with certain MDHI or Helicopter Technology Company (HTC) tail rotor blades installed. AD 2003-08-51 required reducing the retirement life of each tail rotor blade (blade), performing a one-time visual inspection of each blade's pitch horn (pitch horn) for a crack or corrosion, and replacing any cracked blade or any blade that has exceeded its retirement life with an airworthy blade. AD 2003-08-51 also required reporting information to the FAA within 24 hours following the one-time inspection. Since we issued AD 2003-08-51, an accident in England prompted an investigation that showed corrosion on the blade's pitch horn that had not been detected under the paint. This new AD retains some of the requirements of AD 2003-08-51 and also requires paint removal for all pitch horn inspections, inspecting for pitting and the shot peen surface's condition in addition to cracks and corrosion, and adds certain part- numbered blades to the applicability. These actions are intended to prevent a pitch horn from cracking, leading to vibration, loss of tail rotor pitch control, and subsequent loss of tail rotor and helicopter control.

We are adopting a new airworthiness directive (AD) for certain Bell Model 430 helicopters. This AD requires installing a placard on the instrument panel and revising the limitations section of the rotorcraft flight manual (RFM). This AD was prompted by several incidents of third stage engine turbine wheel failures, which were caused by excessive vibrations at certain engine speeds during steady- state operations. These actions are intended to alert pilots to avoid certain engine speeds during steady-state operations, prevent failure of the third stage engine turbine, engine power loss, and subsequent loss of control of the helicopter.

We are adopting a new airworthiness directive (AD) for certain Bell Model 407 helicopters. This AD requires installing a placard beneath the NR/NP dual tachometer and revising the limitations section of the rotorcraft flight manual (RFM). This AD was prompted by several incidents of third stage engine turbine wheel failures, which were caused by excessive vibrations at certain engine speeds during steady- state operations. These actions are intended to alert pilots to avoid certain engine speeds during steady-state operations, prevent failure of the third stage engine turbine, engine power loss, and subsequent loss of control of the helicopter.