Department of Transportation September 9, 2005 – Federal Register Recent Federal Regulation Documents

In accordance with the Paperwork Reduction Act of 1995, this notice announces the Maritime Administration's (MARAD's) intention to request extension of approval for three years of a currently approved information collection.

In accordance with the Paperwork Reduction Act of 1995, this notice announces the Maritime Administration's (MARAD's) intention to request extension of approval for three years of a currently approved information collection.

Pursuant to FAA's rulemaking provisions governing the application, processing, and disposition of petitions for exemption, part 11 of Title 14, Code of Federal Regulations (14 CFR), this notice contains the disposition of certain petitions previously received. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of any petition or its final disposition.

The FAA proposes to adopt a new airworthiness directive (AD) for Lycoming Engines (formerly Textron Lycoming) models 320, 360, and 540 series, ``Parallel Valve'' reciprocating engines, with certain Engine Components Inc. (ECi) cylinder assemblies, part number (P/N) AEL65102 series ``Classic Cast,'' installed. This proposed AD would require replacing these ECi cylinder assemblies. This proposed AD results from reports of about 30 failures of the subject cylinder assemblies marketed by ECi. We are proposing this AD to prevent loss of engine power due to cracks in the cylinder assemblies and possible engine failure caused by separation of a cylinder head.

This notice withdraws the petition by DaimlerChrysler Corporation (DaimlerChrysler) for an exemption from the parts marking requirements of the vehicle theft prevention standard for the Jeep Liberty vehicle line.

This action proposes to establish Class E airspace at Nikolai, AK to the size necessary to contain aircraft executing Standard Instrument Approach Procedures (SIAP). This action is proposed as a result of the development of two new SIAPs. Adoption of this proposal would result in establishing Class E airspace upward from 700 feet (ft.) above the surface at Nikolai, Alaska.

This action proposes to revise Class E airspace at Egegik, AK to the size necessary to contain aircraft executing Standard Instrument Approach Procedures (SIAP). Adoption of this proposal would result in revising Class E airspace upward from 700 feet (ft.) above the surface at Egegik, Alaska.

Consistent with Agency policy, the Federal Aviation Administration (FAA) gives notice of the holding in Creation Aviation, Inc., vs. Textron Financial Corporation, Florida District Court of Appeal, Fourth District, No. 4D04-2178, decided on April 27, 2005. The Court in Creston held that Federal law pertaining to recording with the FAA Aircraft Registry did not preempt a Florida statute requiring that an artisan lien for work on an aircraft first be filed in the county where the work was performed in order to enforce the lien under Florida law. Accordingly, the FAA is advising the public that recording an artisan lien with the FAA Aircraft Registry only, may be insufficient to enforce an artisan lien under Florida law.

The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400 series airplanes. This AD requires a one-time inspection of the fuel and hydraulic tubes, and corrective actions if necessary. This AD also requires modifying fairlead plate assemblies. This AD results from reports of chafing between fuel and hydraulic tubes and the fairlead plate where the tubes pass through the firewall. We are issuing this AD to prevent chafing of the fuel and hydraulic tubes, which could lead to fuel and/or hydraulic fluid leakage in the engine nacelle area and consequent fire or explosion.

The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 757 airplanes. This AD requires inspections of certain wire bundles in the left and right engine-to-wing aft fairings for discrepancies; installation of back-to-back p-clamps between the wire and hydraulic supply tube at the aft end of the right-hand strut only; and associated re-routing of the wire bundles, if necessary. This AD results from a report indicating that a circuit breaker for the fuel shutoff valve tripped due to a wire that chafed against the structure in the flammable leakage zone of the aft fairing, causing a short circuit. We are issuing this AD to prevent chafing between the wire bundle and the structure of the aft fairing, which could result in electrical arcing and subsequent ignition of flammable vapors and possible uncontrollable fire.

This document publishes in the Federal Register an amendment adopting airworthiness directive (AD) 2005-18-51 that was sent previously to all known U.S. owners and operators of Boeing Model 777 airplanes by individual notices. This AD supersedes an existing AD that applies to certain Boeing Model 777-200 and ``300 series airplanes. The existing AD currently requires modification of the operational program software (OPS) of the air data inertial reference unit (ADIRU). This new AD requires installing a certain OPS in the ADIRU, and revising the airplane flight manual to provide the flightcrew with operating instructions for possible ADIRU heading errors and for potential incorrect display of drift angle. This AD results from a recent report of a significant nose-up pitch event. We are issuing this AD to prevent the OPS from using data from faulted (failed) sensors, which could result in anomalies of the fly-by-wire primary flight control, autopilot, auto-throttle, pilot display, and auto-brake systems. These anomalies could result in high pilot workload, deviation from the intended flight path, and possible loss of control of the airplane.

The FAA is superseding an existing airworthiness directive (AD) that applies to all Dassault Model Falcon 10 series airplanes. The existing AD currently requires revising the airplane flight manual (AFM) and installing a placard in the flight deck to prohibit flight into known or forecasted icing conditions. In lieu of the AFM revision and placard installation, that AD allows identifying the part number of each flexible hose in the wing (slat) anti-icing system, performing repetitive inspections of each hose for delamination, and performing corrective actions if necessary. This AD adds the following actions (also in lieu of the AFM revision and placard installation): New repetitive inspections for delamination at reduced intervals, corrective actions if necessary, and an additional AFM revision to include a statement to track flight cycles when the slat anti-icing system is activated. This AD also provides an option to repetitively replace the existing flexible hoses with improved flexible hoses, which terminates the repetitive inspection requirements. This AD results from a report of in-service delamination of a flexible hose in the slat anti-icing system at a time earlier than previously reported. We are issuing this AD to prevent collapse of the flexible hoses in the slat anti-icing system, which could lead to insufficient anti-icing capability and, if icing is encountered in this situation, could result in reduced controllability of the airplane.