Airworthiness Directives; Airbus SAS Airplanes, 88174-88177 [2024-25783]

Download as PDF 88174 Federal Register / Vol. 89, No. 216 / Thursday, November 7, 2024 / Proposed Rules applicability and a new airplane model added to the applicability. The NPRM published in the Federal Register on September 23, 2024 (89 FR 77457). In the NPRM, the FAA proposed to require calculating the CSH for each main wing spar; repetitively inspecting the lower main wing spar bolt holes for crack(s) and non-crack damage and taking corrective actions as needed; replacing or modifying main wing spars at a specified time; and reporting inspection results to Piper and the FAA if any cracks are found during any inspection. In the NPRM, the FAA also proposed to revise the applicability by removing certain airplanes and adding a new airplane model. The FAA is proposing this AD to detect and correct fatigue cracks in the lower main wing spar cap bolt holes. The unsafe condition, if not addressed, could result in a wing separating from the fuselage in flight. lotter on DSK11XQN23PROD with PROPOSALS1 Actions Since the NPRM Was Issued Since issuance of the NPRM, the FAA received a request from Piper to extend the comment period. The commenter stated that the NPRM is complex and could drive substantial costs, among other things. In addition, the commenter stated that two significant hurricanes have prevented operators from performing a dedicated review of the NPRM. To be able to prepare informed and meaningful comments Piper requested an extension of 30 days to the comment period. The FAA has determined that it is appropriate to extend the comment period for the NPRM to give all interested persons additional time to examine the proposed requirements and submit comments. The FAA has determined that extending the comment period an additional 30 days will not compromise the safety of the affected airplanes. Extension of Comment Period The FAA has reviewed the request for extension of the comment period for this notice. The commenter has shown a substantive interest in the proposed policy and good cause for the extension of the comment period. Therefore, in accordance with 14 CFR 11.47(c), the FAA has determined that an extension of the comment period for an additional 30 days to December 9, 2024, is consistent with the public interest, and that good cause exists for taking this action. Accordingly, the comment period for Docket No. FAA–2024–2142 is extended until December 9, 2024. Because no other portion of the proposal or other regulatory information VerDate Sep<11>2014 16:26 Nov 06, 2024 Jkt 265001 has been changed, the entire proposal is not being republished. Issued under authority provided by 49 U.S.C. 106(g), 40113, and 44701. Issued on November 1, 2024. Steven W. Thompson, Acting Deputy Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2024–25883 Filed 11–6–24; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2024–2421; Project Identifier MCAI–2024–00221–T] RIN 2120–AA64 Airworthiness Directives; Airbus SAS Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus SAS Model A300 B4– 600, B4–600R, and F4–600R series airplanes; and Model A300 C4–605R Variant F airplanes (collectively called Model A300–600 series airplanes). This proposed AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products. SUMMARY: The FAA must receive comments on this proposed AD by December 23, 2024. ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE, Washington, DC 20590. DATES: PO 00000 Frm 00002 Fmt 4702 Sfmt 4702 • Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA–2024–2421; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above. Material Incorporated by Reference: • For EASA material identified in this proposed AD, contact EASA, KonradAdenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; website easa.europa.eu. You may find this material on the EASA website at ad.easa.europa.eu. It is also available at regulations.gov under Docket No. FAA– 2024–2421. • You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. Dan Rodina, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 206– 231–3225; email Dan.Rodina@faa.gov. FOR FURTHER INFORMATION CONTACT: SUPPLEMENTARY INFORMATION: Comments Invited The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2024–2421; Project Identifier MCAI–2024–00221–T’’ at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this proposal because of those comments. Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to regulations.gov, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM. E:\FR\FM\07NOP1.SGM 07NOP1 Federal Register / Vol. 89, No. 216 / Thursday, November 7, 2024 / Proposed Rules Confidential Business Information CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as ‘‘PROPIN.’’ The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Dan Rodina, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 206–231–3225; email Dan.Rodina@faa.gov. Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking. lotter on DSK11XQN23PROD with PROPOSALS1 Background EASA, which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2024–0083, dated April 9, 2024 (EASA AD 2024– 0083) (also referred to as the MCAI), to correct an unsafe condition for certain Airbus SAS Model A300–600 series airplanes; and Model A300 C4–620 airplanes. Model A300 C4–620 airplanes are not certificated by the FAA and are not included on the U.S. type certificate data sheet; this proposed AD therefore does not include those airplanes in the applicability. The MCAI states that new or more restrictive airworthiness limitations have been developed. EASA AD 2024–0083 specifies that it requires a task (limitation) already in Airbus A300–600 Airworthiness Limitations Section (ALS) Part 2 Revision 4 that is required by EASA AD 2024–0009 (which corresponds to FAA AD 2024–16–02, Amendment 39–22808 (89 FR 75464, September 16, 2024) (AD 2024–16–02)), and that incorporation of EASA AD 2024–0083 invalidates (terminates) prior instructions for that task. This proposed AD therefore would terminate the limitations required by paragraph (dd) of AD 2024–16–02 for the tasks identified in the material referenced in EASA AD 2024–0083 only. The FAA is proposing this AD to address fatigue cracking, damage, and corrosion in principal structural VerDate Sep<11>2014 16:26 Nov 06, 2024 Jkt 265001 elements. You may examine the MCAI in the AD docket at regulations.gov under Docket No. FAA–2024–2421. Material Incorporated by Reference Under 1 CFR Part 51 The FAA reviewed EASA AD 2024– 0083, which specifies new airworthiness limitations for airplane structures and safe life limits. This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section. FAA’s Determination This product has been approved by the aviation authority of another country and is approved for operation in the United States. Pursuant to the FAA’s bilateral agreement with this State of Design Authority, it has notified the FAA of the unsafe condition described in the MCAI referenced above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop in other products of the same type design. Proposed AD Requirements in This NPRM This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, which are specified in EASA AD 2024–0083 described previously, as incorporated by reference. Any differences with EASA AD 2024–0083 are identified as exceptions in the regulatory text of this proposed AD. This proposed AD would require revisions to certain operator maintenance documents to include new actions (e.g., inspections). Compliance with these actions is required by 14 CFR 91.403(c). For airplanes that have been previously modified, altered, or repaired in the areas addressed by this proposed AD, the operator may not be able to accomplish the actions described in the revisions. In this situation, to comply with 14 CFR 91.403(c), the operator must request approval for an alternative method of compliance (AMOC) according to paragraph (k)(1) of this proposed AD. Explanation of Required Compliance Information In the FAA’s ongoing efforts to improve the efficiency of the AD process, the FAA developed a process to use some civil aviation authority (CAA) ADs as the primary source of information for compliance with PO 00000 Frm 00003 Fmt 4702 Sfmt 4702 88175 requirements for corresponding FAA ADs. The FAA has been coordinating this process with manufacturers and CAAs. As a result, the FAA proposes to incorporate EASA AD 2024–0083 by reference in the FAA final rule. This proposed AD would, therefore, require compliance with EASA AD 2024–0083 through that incorporation, except for any differences identified as exceptions in the regulatory text of this proposed AD. Using common terms that are the same as the heading of a particular section in EASA AD 2024–0083 does not mean that operators need comply only with that section. For example, where the AD requirement refers to ‘‘all required actions and compliance times,’’ compliance with this AD requirement is not limited to the section titled ‘‘Required Action(s) and Compliance Time(s)’’ in EASA AD 2024–0083. Material required by EASA AD 2024– 0083 for compliance will be available at regulations.gov by searching for and locating Docket No. FAA–2024–2421 after the FAA final rule is published. Airworthiness Limitation ADs Using the New Process The FAA’s process of incorporating by reference MCAI ADs as the primary source of information for compliance with corresponding FAA ADs has been limited to certain MCAI ADs (primarily those with service bulletins as the primary source of information for accomplishing the actions required by the FAA AD). However, the FAA is now expanding the process to include MCAI ADs that require a change to airworthiness limitation documents, such as airworthiness limitation sections. For these ADs that incorporate by reference an MCAI AD that changes airworthiness limitations, the FAA requirements are unchanged. Operators must revise the existing maintenance or inspection program, as applicable, to incorporate the information specified in the new airworthiness limitation document. The airworthiness limitations must be followed according to 14 CFR 91.403(c) and 91.409(e). The previous format of the airworthiness limitation ADs included a paragraph that specified that no alternative actions (e.g., inspections) or intervals may be used unless the actions and intervals are approved as an AMOC in accordance with the procedures specified in the AMOC paragraph under ‘‘Additional AD Provisions.’’ This new format includes a ‘‘Provisions for Alternative Actions and Intervals’’ paragraph that does not specifically refer to AMOCs, but operators may still E:\FR\FM\07NOP1.SGM 07NOP1 88176 Federal Register / Vol. 89, No. 216 / Thursday, November 7, 2024 / Proposed Rules request an AMOC to use an alternative action or interval. Costs of Compliance The FAA estimates that this AD, if adopted as proposed, would affect 128 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD: The FAA has determined that revising the existing maintenance or inspection program takes an average of 90 workhours per operator, although the agency recognizes that this number may vary from operator to operator. Since operators incorporate maintenance or inspection program changes for their affected fleet(s), the FAA has determined that a per-operator estimate is more accurate than a per-airplane estimate. Therefore, the agency estimates the average total cost per operator to be $7,650 (90 work-hours × $85 per work-hour). lotter on DSK11XQN23PROD with PROPOSALS1 Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings The FAA has determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Would not affect intrastate aviation in Alaska, and (3) Would not have a significant economic impact, positive or negative, VerDate Sep<11>2014 16:26 Nov 06, 2024 Jkt 265001 on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive: ■ Airbus SAS: Docket No. FAA–2024–2421; Project Identifier MCAI–2024–00221–T. (a) Comments Due Date The FAA must receive comments on this airworthiness directive (AD) by December 23, 2024. (b) Affected ADs This AD affects AD 2024–16–02, Amendment 39–22808 (89 FR 75464, September 16, 2024) (AD 2024–16–02). (c) Applicability This AD applies to the Airbus SAS airplanes identified in paragraphs (c)(1) through (4) of this AD, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2024– 0083, dated April 9, 2024 (EASA AD 2024– 0083). (1) Model A300 B4–601, B4–603, B4–620, and B4–622 airplanes. (2) Model A300 B4–605R and B4–622R airplanes. (3) Model A300 C4–605R Variant F airplanes. (4) Model A300 F4–605R and F4–622R airplanes. (d) Subject Air Transport Association (ATA) of America Code 05, Time Limits/Maintenance Checks. (e) Unsafe Condition This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address fatigue cracking, damage, and corrosion in principal structural elements. The unsafe condition, if not addressed, could result in reduced structural integrity of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. PO 00000 Frm 00004 Fmt 4702 Sfmt 4702 (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2024–0083. (h) Exceptions to EASA AD 2024–0083 (1) This AD does not adopt the requirements specified in paragraphs (1) and (2) of EASA AD 2024–0083. (2) Paragraph (3) of EASA AD 2024–0083 specifies revising ‘‘the approved AMP,’’ within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, within 90 days after the effective date of this AD. (3) The initial compliance time for doing the tasks specified in paragraph (3) of EASA AD 2024–0083 is at the applicable ‘‘associated thresholds’’ as incorporated by the requirements of paragraph (3) of EASA AD 2024–0083, or within 90 days after the effective date of this AD, whichever occurs later. (4) This AD does not adopt the provisions specified in paragraph (4) of EASA AD 2024– 0083. (5) This AD does not adopt the ‘‘Remarks’’ section of EASA AD 2024–0083. (i) Provisions for Alternative Actions and Intervals After the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections) and intervals are allowed unless they are approved as specified in the provisions of the ‘‘Ref. Publications’’ section of EASA AD 2024–0083. (j) Terminating Action for Certain Tasks Required by AD 2024–16–02 Accomplishing the actions required by this AD terminates the corresponding requirements of AD 2024–16–02 for the tasks identified in the material referenced in EASA AD 2024–0083 only. (k) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the International Validation Branch, send it to the attention of the person identified in paragraph (l) of this AD and email to: AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS’s E:\FR\FM\07NOP1.SGM 07NOP1 Federal Register / Vol. 89, No. 216 / Thursday, November 7, 2024 / Proposed Rules EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (l) Additional Information For more information about this AD, contact Dan Rodina, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 206– 231–3225; email Dan.Rodina@faa.gov. (m) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2024–0083, dated April 9, 2024. (ii) [Reserved] (3) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; website easa.europa.eu. You may find this material on the EASA website at ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ ibr-locations or email fr.inspection@nara.gov. Issued on November 1, 2024. Peter A. White, Deputy Director, Integrated Certificate Management Division, Aircraft Certification Service. [FR Doc. 2024–25783 Filed 11–6–24; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 71 [Docket No. FAA–2024–1979; Airspace Docket No. 24–ASO–20] RIN 2120–AA66 Amendment of Class E Airspace; Kinston, NC Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). lotter on DSK11XQN23PROD with PROPOSALS1 AGENCY: This action proposes to amend Class E airspace extending upward from 700 feet above the surface for Kinston, NC, by adding airspace for Lenoir Regional Hospital Heliport, SUMMARY: VerDate Sep<11>2014 16:26 Nov 06, 2024 Jkt 265001 Kinston, NC. This action would also update the coordinates for Kinston Regional Jetport at Stallings Field, Kinston, NC. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations at this airport. DATES: Comments must be received on or before December 23, 2024. ADDRESSES: Send comments identified by FAA Docket No. FAA–2024–1979 and Airspace Docket No. 24–ASO–20 using any of the following methods: * Federal eRulemaking Portal: Go to www.regulations.gov and follow the online instructions for sending your comments electronically. * Mail: Docket Operations, M–30; U.S. Department of Transportation, 1200 New Jersey Avenue SE, Room W12–140, West Building Ground Floor, Washington, DC 20590–0001. * Hand Delivery or Courier: Take comments to Docket Operations in Room W12–140 of the West Building Ground Floor at 1200 New Jersey Avenue SE, Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except for Federal holidays. * Fax: Fax comments to Docket Operations at (202) 493–2251. Docket: Background documents or comments received may be read at www.regulations.gov at any time. Follow the online instructions for accessing the docket or go to the Docket Operations in Room W12–140 of the West Building Ground Floor at 1200 New Jersey Avenue SE, Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except for Federal holidays. FAA Order JO 7400.11J Airspace Designations and Reporting Points and subsequent amendments can be viewed online at www.faa.gov/air_traffic/ publications/. You may also contact the Rules and Regulations Group, Office of Policy, Federal Aviation Administration, 800 Independence Avenue SW, Washington, DC 20591; telephone: (202) 267–8783. FOR FURTHER INFORMATION CONTACT: Marc Ellerbee, Operations Support Group, Eastern Service Center, Federal Aviation Administration, 1701 Columbia Avenue, College Park, GA 30337; Telephone: (404) 305–5589. SUPPLEMENTARY INFORMATION: Authority for This Rulemaking The FAA’s authority to issue rules regarding aviation safety is found in Title 49 of the United States Code. Subtitle I, Section 106 describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the PO 00000 Frm 00005 Fmt 4702 Sfmt 4702 88177 agency’s authority. This rulemaking is promulgated under the authority described in Subtitle VII, Part A, Subpart I, Section 40103. Under that section, the FAA is charged with prescribing regulations to assign the use of airspace necessary to ensure the safety of aircraft and the efficient use of airspace. This regulation is within the scope of that authority, as it would amend Class E airspace in Kinston, NC. Comments Invited The FAA invites interested persons to participate in this rulemaking by submitting written comments, data, or views. Comments are specifically invited on the overall regulatory, aeronautical, economic, environmental, and energy-related aspects of the proposal. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. To ensure the docket does not contain duplicate comments, commenters should submit only one time if comments are filed electronically, or commenters should send only one copy of written comments if comments are filed in writing. The FAA will file in the docket all comments it receives, as well as a report summarizing each substantive public contact with FAA personnel concerning this proposed rulemaking. Before acting on this proposal, the FAA will consider all comments it receives on or before the closing date for comments. The FAA will consider comments filed after the comment period has closed if it is possible to do so without incurring expense or delay. The FAA may change this proposal in light of the comments it receives. Privacy: In accordance with 5 U.S.C. 553(c), DOT solicits comments from the public to better inform its rulemaking process. DOT posts these comments, without edits, including any personal information the commenter provides, to www.regulations.gov, as described in the system of records notice (DOT/ALL– 14 FDMS), which can be reviewed at www.dot.gov/privacy. Availability of Rulemaking Documents An electronic copy of this document may be downloaded through the internet at www.regulations.gov. Recently published rulemaking documents can also be accessed through the FAA’s web page at www.faa.gov/air_ traffic/publications/airspace_ amendments/. You may review the public docket containing the proposal, any comments received, and any final disposition in E:\FR\FM\07NOP1.SGM 07NOP1

Agencies

[Federal Register Volume 89, Number 216 (Thursday, November 7, 2024)]
[Proposed Rules]
[Pages 88174-88177]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-25783]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2024-2421; Project Identifier MCAI-2024-00221-T]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus SAS Model A300 B4-600, B4-600R, and F4-600R series 
airplanes; and Model A300 C4-605R Variant F airplanes (collectively 
called Model A300-600 series airplanes). This proposed AD was prompted 
by a determination that new or more restrictive airworthiness 
limitations are necessary. This proposed AD would require revising the 
existing maintenance or inspection program, as applicable, to 
incorporate new or more restrictive airworthiness limitations, as 
specified in a European Union Aviation Safety Agency (EASA) AD, which 
is proposed for incorporation by reference (IBR). The FAA is proposing 
this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by December 
23, 2024.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2024-2421; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For EASA material identified in this proposed AD, contact 
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; website easa.europa.eu. You may 
find this material on the EASA website at ad.easa.europa.eu. It is also 
available at regulations.gov under Docket No. FAA-2024-2421.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aviation Safety Engineer, 
FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 206-
231-3225; email [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2024-2421; 
Project Identifier MCAI-2024-00221-T'' at the beginning of your 
comments. The most helpful comments reference a specific portion of the 
proposal, explain the reason for any recommended change, and include 
supporting data. The FAA will consider all comments received by the 
closing date and may amend this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

[[Page 88175]]

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to Dan 
Rodina, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 206-231-3225; email [email protected]. 
Any commentary that the FAA receives which is not specifically 
designated as CBI will be placed in the public docket for this 
rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2024-0083, dated April 9, 2024 (EASA 
AD 2024-0083) (also referred to as the MCAI), to correct an unsafe 
condition for certain Airbus SAS Model A300-600 series airplanes; and 
Model A300 C4-620 airplanes. Model A300 C4-620 airplanes are not 
certificated by the FAA and are not included on the U.S. type 
certificate data sheet; this proposed AD therefore does not include 
those airplanes in the applicability. The MCAI states that new or more 
restrictive airworthiness limitations have been developed.
    EASA AD 2024-0083 specifies that it requires a task (limitation) 
already in Airbus A300-600 Airworthiness Limitations Section (ALS) Part 
2 Revision 4 that is required by EASA AD 2024-0009 (which corresponds 
to FAA AD 2024-16-02, Amendment 39-22808 (89 FR 75464, September 16, 
2024) (AD 2024-16-02)), and that incorporation of EASA AD 2024-0083 
invalidates (terminates) prior instructions for that task. This 
proposed AD therefore would terminate the limitations required by 
paragraph (dd) of AD 2024-16-02 for the tasks identified in the 
material referenced in EASA AD 2024-0083 only.
    The FAA is proposing this AD to address fatigue cracking, damage, 
and corrosion in principal structural elements. You may examine the 
MCAI in the AD docket at regulations.gov under Docket No. FAA-2024-
2421.

Material Incorporated by Reference Under 1 CFR Part 51

    The FAA reviewed EASA AD 2024-0083, which specifies new 
airworthiness limitations for airplane structures and safe life limits. 
This material is reasonably available because the interested parties 
have access to it through their normal course of business or by the 
means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this NPRM after determining that 
the unsafe condition described previously is likely to exist or develop 
in other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations, which are specified in EASA AD 
2024-0083 described previously, as incorporated by reference. Any 
differences with EASA AD 2024-0083 are identified as exceptions in the 
regulatory text of this proposed AD.
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections). 
Compliance with these actions is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance (AMOC) according to 
paragraph (k)(1) of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate EASA AD 2024-0083 by reference in the FAA 
final rule. This proposed AD would, therefore, require compliance with 
EASA AD 2024-0083 through that incorporation, except for any 
differences identified as exceptions in the regulatory text of this 
proposed AD. Using common terms that are the same as the heading of a 
particular section in EASA AD 2024-0083 does not mean that operators 
need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2024-
0083. Material required by EASA AD 2024-0083 for compliance will be 
available at regulations.gov by searching for and locating Docket No. 
FAA-2024-2421 after the FAA final rule is published.

Airworthiness Limitation ADs Using the New Process

    The FAA's process of incorporating by reference MCAI ADs as the 
primary source of information for compliance with corresponding FAA ADs 
has been limited to certain MCAI ADs (primarily those with service 
bulletins as the primary source of information for accomplishing the 
actions required by the FAA AD). However, the FAA is now expanding the 
process to include MCAI ADs that require a change to airworthiness 
limitation documents, such as airworthiness limitation sections.
    For these ADs that incorporate by reference an MCAI AD that changes 
airworthiness limitations, the FAA requirements are unchanged. 
Operators must revise the existing maintenance or inspection program, 
as applicable, to incorporate the information specified in the new 
airworthiness limitation document. The airworthiness limitations must 
be followed according to 14 CFR 91.403(c) and 91.409(e).
    The previous format of the airworthiness limitation ADs included a 
paragraph that specified that no alternative actions (e.g., 
inspections) or intervals may be used unless the actions and intervals 
are approved as an AMOC in accordance with the procedures specified in 
the AMOC paragraph under ``Additional AD Provisions.'' This new format 
includes a ``Provisions for Alternative Actions and Intervals'' 
paragraph that does not specifically refer to AMOCs, but operators may 
still

[[Page 88176]]

request an AMOC to use an alternative action or interval.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 128 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the agency recognizes that this number may vary from operator 
to operator. Since operators incorporate maintenance or inspection 
program changes for their affected fleet(s), the FAA has determined 
that a per-operator estimate is more accurate than a per-airplane 
estimate. Therefore, the agency estimates the average total cost per 
operator to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA has determined that this proposed AD would not have 
federalism implications under Executive Order 13132. This proposed AD 
would not have a substantial direct effect on the States, on the 
relationship between the national government and the States, or on the 
distribution of power and responsibilities among the various levels of 
government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Airbus SAS: Docket No. FAA-2024-2421; Project Identifier MCAI-2024-
00221-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by December 23, 2024.

(b) Affected ADs

    This AD affects AD 2024-16-02, Amendment 39-22808 (89 FR 75464, 
September 16, 2024) (AD 2024-16-02).

(c) Applicability

    This AD applies to the Airbus SAS airplanes identified in 
paragraphs (c)(1) through (4) of this AD, certificated in any 
category, as identified in European Union Aviation Safety Agency 
(EASA) AD 2024-0083, dated April 9, 2024 (EASA AD 2024-0083).
    (1) Model A300 B4-601, B4-603, B4-620, and B4-622 airplanes.
    (2) Model A300 B4-605R and B4-622R airplanes.
    (3) Model A300 C4-605R Variant F airplanes.
    (4) Model A300 F4-605R and F4-622R airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Unsafe Condition

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to address fatigue cracking, damage, and corrosion 
in principal structural elements. The unsafe condition, if not 
addressed, could result in reduced structural integrity of the 
airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2024-0083.

(h) Exceptions to EASA AD 2024-0083

    (1) This AD does not adopt the requirements specified in 
paragraphs (1) and (2) of EASA AD 2024-0083.
    (2) Paragraph (3) of EASA AD 2024-0083 specifies revising ``the 
approved AMP,'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, within 90 days after the effective date of this AD.
    (3) The initial compliance time for doing the tasks specified in 
paragraph (3) of EASA AD 2024-0083 is at the applicable ``associated 
thresholds'' as incorporated by the requirements of paragraph (3) of 
EASA AD 2024-0083, or within 90 days after the effective date of 
this AD, whichever occurs later.
    (4) This AD does not adopt the provisions specified in paragraph 
(4) of EASA AD 2024-0083.
    (5) This AD does not adopt the ``Remarks'' section of EASA AD 
2024-0083.

(i) Provisions for Alternative Actions and Intervals

    After the existing maintenance or inspection program has been 
revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections) and intervals are allowed unless they 
are approved as specified in the provisions of the ``Ref. 
Publications'' section of EASA AD 2024-0083.

(j) Terminating Action for Certain Tasks Required by AD 2024-16-02

    Accomplishing the actions required by this AD terminates the 
corresponding requirements of AD 2024-16-02 for the tasks identified 
in the material referenced in EASA AD 2024-0083 only.

(k) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the manager of the 
International Validation Branch, send it to the attention of the 
person identified in paragraph (l) of this AD and email to: 
[email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Airbus SAS's

[[Page 88177]]

EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.

(l) Additional Information

    For more information about this AD, contact Dan Rodina, Aviation 
Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone 206-231-3225; email [email protected].

(m) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the material listed in this paragraph 
under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this material as applicable to do the actions 
required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2024-0083, 
dated April 9, 2024.
    (ii) [Reserved]
    (3) For EASA material identified in this AD, contact EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; website easa.europa.eu. You may 
find this material on the EASA website at ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (5) You may view this material at the National Archives and 
Records Administration (NARA). For information on the availability 
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected].

    Issued on November 1, 2024.
Peter A. White,
Deputy Director, Integrated Certificate Management Division, Aircraft 
Certification Service.
[FR Doc. 2024-25783 Filed 11-6-24; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.