Airworthiness Directives; Airbus SAS Airplanes, 27368-27371 [2024-08109]

Agencies

• Federal Aviation Administration
• DEPARTMENT OF TRANSPORTATION

[Federal Register Volume 89, Number 75 (Wednesday, April 17, 2024)]
[Rules and Regulations]
[Pages 27368-27371]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-08109]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2024-0764; Project Identifier MCAI-2023-01017-T; 
Amendment 39-22716; AD 2024-06-11]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Airbus SAS Model A310 series airplanes. This AD was prompted by a 
determination that new or more restrictive airworthiness limitations 
are necessary. This AD requires revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations, as specified in a European Union 
Aviation Safety Agency (EASA) AD, which is incorporated by reference. 
The FAA is issuing this AD to address the unsafe condition on these 
products.

DATES: This AD is effective May 2, 2024.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of May 2, 2024.
    The FAA must receive comments on this AD by June 3, 2024.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2024-0764; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For EASA material that is incorporated by reference in 
this final rule, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, 
Germany; telephone +49 221 8999 000; email [email protected]; website 
easa.europa.eu. You may find this material on the EASA website at 
ad.easa.europa.eu.
     You may view this material that is incorporated by 
reference at the FAA, Airworthiness Products Section, Operational 
Safety Branch, 2200 South 216th St., Des Moines, WA. For information on 
the availability of this material at the FAA, call 206-231-3195. It is 
also available at regulations.gov under Docket No. FAA-2024-0764.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, Large 
Aircraft Section, FAA, International Validation Branch, 2200 South 
216th St., Des Moines, WA 98198; telephone 206-231-3225; email 
[email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written data, views, or arguments 
about this final rule. Send your comments to an address listed under 
ADDRESSES. Include ``Docket No. FAA-2024-0764; Project Identifier MCAI-
2023-01017-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the final rule, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this final rule because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this final rule.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this AD contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this final rule, it is important that you clearly designate the 
submitted comments as CBI. Please mark each page of your submission 
containing CBI as ``PROPIN.'' The FAA will treat such marked 
submissions as confidential under the FOIA, and they will not be placed 
in the public docket of this final rule. Submissions containing CBI 
should be sent to Dan Rodina, Aerospace Engineer, Large Aircraft 
Section, FAA, International Validation Branch, 2200 South 216th St., 
Des Moines, WA 98198; telephone 206-231-3225; email [email protected]. 
Any commentary that the FAA receives which is not specifically 
designated as CBI will be placed in the public docket for this 
rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2023-0173, dated September 20, 2023 
(EASA AD

[[Page 27369]]

2023-0173) (referred to after this as the MCAI), to correct an unsafe 
condition on all Airbus A310-203, A310-204, A310-221, A310-222, A310-
203C, A310-304, A310-308, A310-322, A310-324, and A310-325 airplanes. 
Model A310-203C and A310-308 airplanes are not certificated by the FAA 
and are not included on the U.S. type certificate data sheet; this AD 
therefore does not include those airplanes in the applicability. The 
MCAI states that new or more restrictive airworthiness limitations have 
been developed.
    EASA AD 2023-0173 specifies that it requires a task (limitation) 
already in Airbus A310 ALS Part 1 SL-ALI Revision 02 that is required 
by EASA AD 2017-0204 (which corresponds to FAA AD 2018-18-19, Amendment 
39-19398 (83 FR 47056, September 18, 2018) (AD 2018-18-19)) or EASA AD 
2022-0172 (which corresponds to FAA AD 2023-04-09, Amendment 39-22356 
(88 FR 20746, April 7, 2023) (AD 2023-04-09)), and that incorporation 
of EASA AD 2017-0204 or EASA AD 2022-0172 invalidates (terminates) 
prior instructions for that task. This AD therefore terminates the 
limitations required by paragraph (g) of AD 2018-18-19 and AD 2023-04-
09, for the tasks identified in the service information referenced in 
EASA AD 2023-0173 only.
    The FAA is issuing this AD to address fatigue damage in principal 
structural elements. The unsafe condition, if not addressed, could 
result in reduced structural integrity of the airplane.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2024-0764.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed EASA AD 2023-0173. This service information 
specifies new or more restrictive airworthiness limitations for 
airplane structures and safe life limits. This material is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this AD after determining that the 
unsafe condition described previously is likely to exist or develop on 
other products of the same type design.

AD Requirements

    This AD requires revising the existing maintenance or inspection 
program, as applicable, to incorporate new or more restrictive 
airworthiness limitations, which are specified in EASA AD 2023-0173 
described previously, as incorporated by reference. Any differences 
with EASA AD 2023-0173 are identified as exceptions in the regulatory 
text of this AD.
    This AD requires revisions to certain operator maintenance 
documents to include new actions (e.g., inspections). Compliance with 
these actions is required by 14 CFR 91.403(c). For airplanes that have 
been previously modified, altered, or repaired in the areas addressed 
by this AD, the operator may not be able to accomplish the actions 
described in the revisions. In this situation, to comply with 14 CFR 
91.403(c), the operator must request approval for an alternative method 
of compliance (AMOC) according to paragraph (k)(1) of this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, 
EASA AD 2023-0173 is incorporated by reference in this AD. This AD 
requires compliance with EASA AD 2023-0173 through that incorporation, 
except for any differences identified as exceptions in the regulatory 
text of this AD. Using common terms that are the same as the heading of 
a particular section in EASA AD 2023-0173 does not mean that operators 
need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2023-
0173. Service information required by EASA AD 2023-0173 for compliance 
will be available at regulations.gov under Docket No. FAA-2024-0764 
after this final rule is published.

Airworthiness Limitation ADs Using the New Process

    The FAA's process of incorporating by reference MCAI ADs as the 
primary source of information for compliance with corresponding FAA ADs 
has been limited to certain MCAI ADs (primarily those with service 
bulletins as the primary source of information for accomplishing the 
actions required by the FAA AD). However, the FAA is now expanding the 
process to include MCAI ADs that require a change to airworthiness 
limitation documents, such as airworthiness limitation sections.
    For these ADs that incorporate by reference an MCAI AD that changes 
airworthiness limitations, the FAA requirements are unchanged. 
Operators must revise the existing maintenance or inspection program, 
as applicable, to incorporate the information specified in the new 
airworthiness limitation document. The airworthiness limitations must 
be followed according to 14 CFR 91.403(c) and 91.409(e).
    The previous format of the airworthiness limitation ADs included a 
paragraph that specified that no alternative actions (e.g., inspections 
or intervals) may be used unless the actions and intervals are approved 
as an AMOC in accordance with the procedures specified in the AMOCs 
paragraph under ``Additional AD Provisions.'' This new format includes 
a ``New Provisions for Alternative Actions and Intervals'' paragraph 
that does not specifically refer to AMOCs, but operators may still 
request an AMOC to use an alternative action or interval.

Justification for Immediate Adoption and Determination of the Effective 
Date

    Section 553(b)(3)(B) of the Administrative Procedure Act (APA) (5 
U.S.C. 551 et seq.) authorizes agencies to dispense with notice and 
comment procedures for rules when the agency, for ``good cause,'' finds 
that those procedures are ``impracticable, unnecessary, or contrary to 
the public interest.'' Under this section, an agency, upon finding good 
cause, may issue a final rule without providing notice and seeking 
comment prior to issuance. Further, section 553(d) of the APA 
authorizes agencies to make rules effective in less than thirty days, 
upon a finding of good cause.
    There are currently no domestic operators of these products. 
Accordingly, notice and opportunity for prior public comment are 
unnecessary, pursuant to 5 U.S.C. 553(b)(3)(B). In addition, for the 
foregoing reason(s), the FAA finds that good cause exists pursuant to 5 
U.S.C. 553(d) for making this amendment effective in less than 30 days.

[[Page 27370]]

Regulatory Flexibility Act

    The requirements of the Regulatory Flexibility Act (RFA) do not 
apply when an agency finds good cause pursuant to 5 U.S.C. 553 to adopt 
a rule without prior notice and comment. Because the FAA has determined 
that it has good cause to adopt this rule without notice and comment, 
RFA analysis is not required.

Costs of Compliance

    Currently, there are no affected U.S.-registered airplanes. For any 
affected airplane that may be imported and placed on the U.S. Register 
in the future, the FAA provides the following cost estimates to comply 
with this AD:
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the agency recognizes that this number may vary from operator 
to operator. Since operators incorporate maintenance or inspection 
program changes for their affected fleet(s), the FAA has determined 
that a per-operator estimate is more accurate than a per-airplane 
estimate.
    The FAA estimates the total cost per operator for the new actions 
to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national Government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2024-06-11 Airbus SAS: Amendment 39-22716; Docket No. FAA-2024-0764; 
Project Identifier MCAI-2023-01017-T.

(a) Effective Date

    This airworthiness directive (AD) is effective May 2, 2024.

(b) Affected ADs

    This AD affects AD 2018-18-19, Amendment 39-19398 (83 FR 47056, 
September 18, 2018) (AD 2018-18-19) and AD 2023-04-09, Amendment 39-
22356 (88 FR 20746, April 7, 2023) (AD 2023-04-09).

(c) Applicability

    This AD applies to all Airbus SAS Model A310-203, -204, -221, -
222, -304, -322, -324, and -325 airplanes, certificated in any 
category.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Unsafe Condition

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to address fatigue damage in principal structural 
elements. The unsafe condition, if not addressed, could result in 
reduced structural integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2023-0173, dated September 20, 2023 (EASA AD 2023-0173). Where EASA 
AD 2023-0173 affects the same airworthiness limitations as those in 
EASA AD 2017-0204 or EASA AD 2022-0172, the airworthiness 
limitations referenced in EASA AD 2023-0173 prevail.

(h) Exceptions to EASA AD 2023-0173

    (1) This AD does not adopt the requirements specified in 
paragraph (1) of EASA AD 2023-0173.
    (2) Paragraph (2) of EASA AD 2023-0173 specifies revising ``the 
approved AMP,'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, within 90 days after the effective date of this AD.
    (3) The initial compliance time for doing the tasks specified in 
paragraph (2) of EASA AD 2023-0173 is at the applicable 
``limitations'' as incorporated by the requirements of paragraph (2) 
of EASA AD 2023-0173, or within 90 days after the effective date of 
this AD, whichever occurs later.
    (4) This AD does not adopt the ``Remarks'' section of EASA AD 
2023-0173.

(i) Provisions for Alternative Actions and Intervals

    After the existing maintenance or inspection program has been 
revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections) and intervals are allowed unless they 
are approved as specified in the provisions of the ``Ref. 
Publications'' section of EASA AD 2023-0173.

(j) Terminating Action for Certain Tasks Required by AD 2018-18-19 and 
AD 2023-04-09

    Accomplishing the actions required by this AD terminates the 
corresponding requirements of AD 2018-18-19 and AD 2023-04-09 for 
the tasks identified in the service information referenced in EASA 
AD 2023-0173 only.

(k) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the manager of the 
International Validation Branch, mail it to the address identified 
in paragraph (l) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.

[[Page 27371]]

    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.

(l) Additional Information

    For more information about this AD, contact Dan Rodina, 
Aerospace Engineer, Large Aircraft Section, FAA, International 
Validation Branch, 2200 South 216th St., Des Moines, WA 98198; 
telephone 206-231-3225; email [email protected].

(m) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (3) The following service information was approved for IBR on 
May 2, 2024.
    (i) European Union Aviation Safety Agency (EASA) AD 2023-0173, 
dated September 20, 2023.
    (ii) [Reserved]
    (4) For EASA AD 2023-0173, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this EASA 
AD on the EASA website at ad.easa.europa.eu.
    (5) You may view this material that is incorporated by reference 
at the FAA, Airworthiness Products Section, Operational Safety 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195.
    (6) You may view this material at the National Archives and 
Records Administration (NARA). For information on the availability 
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations, or email [email protected].

    Issued on March 20, 2024.
Victor Wicklund,
Deputy Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2024-08109 Filed 4-16-24; 8:45 am]
BILLING CODE 4910-13-P