Airworthiness Directives; Airbus SAS Airplanes, 69110-69112 [2023-22070]

Agencies

• Federal Aviation Administration
• DEPARTMENT OF TRANSPORTATION

[Federal Register Volume 88, Number 192 (Thursday, October 5, 2023)]
[Proposed Rules]
[Pages 69110-69112]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-22070]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2023-1897; Project Identifier MCAI-2023-00921-T]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus SAS Model A320-214, A320-216, A320-251N, A320-271N, 
and A321-253NX airplanes. This proposed AD was prompted by a quality 
review of the forward cargo door frame-to-fuselage skin panel assembly 
identified several fastener holes that deviated from the manufacturing 
requirements. This proposed AD would require repetitive special 
detailed inspections of the affected area for discrepancies and, 
depending on findings, accomplishment of applicable corrective actions, 
as specified in a European Union Aviation Safety Agency (EASA) AD, 
which is proposed for incorporation by reference (IBR). The FAA is 
proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by November 
20, 2023.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2023-1897; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For material that is proposed for IBR in this AD, contact 
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; website easa.europa.eu. You may 
find this material on the EASA website ad.easa.europa.eu. It is also 
available at regulations.gov under Docket No. FAA-2023-1897.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th Street, 
Des Moines, WA. For information on the availability of this material at 
the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Timothy Dowling, Aviation Safety 
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone: 206-231-3667; email: [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2023-1897; Project Identifier 
MCAI-2023-00921-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Timothy Dowling, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, 
Suite 410, Westbury, NY 11590; telephone: 206-231-3667; email: 
[email protected]. Any commentary that the FAA receives which 
is not specifically designated as CBI will be placed in the public 
docket for this rulemaking.

[[Page 69111]]

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2023-0153, dated July 26, 2023 (EASA 
AD 2023-0153) (also referred to as the MCAI), to correct an unsafe 
condition for certain Airbus SAS Model A320-214, A320-216, A320-251N, 
A320-271N, and A321-253NX airplanes. The MCAI states a quality review 
of the forward cargo door frame-to-fuselage skin panel assembly 
identified several drillings as deviating from manufacturing 
requirements, creating oversized fastener holes, which could lead to 
cracking. This condition, if not addressed, could lead to reduced 
structural integrity of the fuselage.
    The FAA is proposing this AD to address the unsafe condition on 
these products. You may examine the MCAI in the AD docket at 
regulations.gov under Docket No. FAA-2023-1897.

Related Service Information Under 1 CFR Part 51

    EASA AD 2023-0153 specifies procedures for repetitive special 
detailed inspections of the affected area for discrepancies and, 
depending on findings, accomplishment of applicable corrective action. 
The special detailed inspection consists of a rototest inspection for 
cracking of the forward cargo door frame to fuselage skin panel, and if 
no cracking is found, checking the fastener hole diameters. Corrective 
actions include installing oversized fasteners if the fastener hole 
diameter is less than or equal to the specified nominal diameter, 
contacting the manufacturer for repair instructions if the fastener 
hole diameter is greater than the specified nominal diameter, and 
repairing any cracking by contacting the manufacturer for repair 
instructions.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this NPRM after determining that 
the unsafe condition described previously is likely to exist or develop 
in other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2023-0153 described previously, except for any differences 
identified as exceptions in the regulatory text of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate EASA AD 2023-0153 by reference in the FAA 
final rule. This proposed AD would, therefore, require compliance with 
EASA AD 2023-0153 in its entirety through that incorporation, except 
for any differences identified as exceptions in the regulatory text of 
this proposed AD. Using common terms that are the same as the heading 
of a particular section in EASA AD 2023-0153 does not mean that 
operators need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2023-
0153. Service information required by EASA AD 2023-0153 for compliance 
will be available at regulations.gov under Docket No. FAA-2023-1897 
after the FAA final rule is published.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 8 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
42.5 work-hours x $85 per hour = $3,613......................            $100           $3,713          $29,704
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition repairs specified in this proposed AD.
    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this proposed AD may be covered under warranty, thereby reducing the 
cost impact on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative,

[[Page 69112]]

on a substantial number of small entities under the criteria of the 
Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Airbus SAS: Docket No. FAA-2023-1897; Project Identifier MCAI-2023-
00921-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by November 20, 2023.

 (b) Affected ADs

    None.

 (c) Applicability

    This AD applies to Airbus SAS Model A320-214, A320-216, A320-
251N, A320-271N, and A321-253NX airplanes, certificated in any 
category, as identified in European Union Aviation Safety Agency 
(EASA) AD 2023-0153, dated July 26, 2023 (EASA AD 2023-0153).

 (d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

 (e) Unsafe Condition

    This AD was prompted by a quality review of the forward cargo 
door frame-to-fuselage skin panel assembly identified several 
drillings as deviating from manufacturing requirements, creating 
oversized fastener holes. The FAA is issuing this AD to address 
oversized fastener holes and cracking. The unsafe condition, if not 
detected and corrected, could result in reduced structural integrity 
of the fuselage.

 (f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

 (g) Requirements

    Except as specified in paragraphs (h) and (i) of this AD: Comply 
with all required actions and compliance times specified in, and in 
accordance with, EASA AD 2023-0153.

 (h) Exceptions to EASA AD 2023-0153

    (1) Where EASA AD 2023-0153 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) Where paragraph (2) of EASA AD 2023-0153 specifies ``If, 
during any SDI as required by paragraph (1) of this AD, any 
discrepancy is detected, as defined in the SB, before next flight, 
accomplish the applicable corrective action(s) in accordance with 
the instructions of the SB,'' this AD requires replacing those words 
with ``If, during any SDI as required by paragraph (1) of this AD, 
no cracking is found, before next flight, accomplish the applicable 
corrective actions in accordance with the instructions of the SB; 
and if, during any SDI as required by paragraph (1) of this AD, any 
cracking is found, before next flight, repair the cracking using a 
method approved by the Manager, International Validation Branch, 
FAA; or EASA; or Airbus SAS's EASA Design Organization Approval 
(DOA). If approved by the DOA, the approval must include the DOA-
authorized signature.''
    (3) Where paragraph (3) of EASA AD 2023-0153 specifies the 
repair be done in accordance with ``approved Airbus repair 
instructions,'' for this AD the repair must have been done using a 
method approved by the Manager, International Validation Branch, 
FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (4) This AD does not adopt the ``Remarks'' section of EASA AD 
2023-0153.

 (i) No Reporting Requirement

    Although the service information referenced in EASA AD 2023-0153 
specifies to submit certain information to the manufacturer, this AD 
does not include that requirement.

 (j) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the manager of the 
International Validation Branch, mail it to the address in paragraph 
(k) of this AD or email to: [email protected]. If mailing 
information, also submit information by email. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the responsible Flight 
Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If 
approved by the DOA, the approval must include the DOA-authorized 
signature.
    (3) Required for Compliance (RC): Except as required by 
paragraphs (i) and (j)(2) of this AD, if any service information 
contains procedures or tests that are identified as RC, those 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures and tests identified as 
RC can be done and the airplane can be put back in an airworthy 
condition. Any substitutions or changes to procedures or tests 
identified as RC require approval of an AMOC.

 (k) Additional Information

    For more information about this AD, contact Timothy Dowling, 
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone: 206-231-3667; email: 
[email protected].

 (l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2023-0153, 
dated July 26, 2023.
    (ii) [Reserved]
    (3) For EASA AD 2023-0153, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this EASA 
AD on the EASA website ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th 
Street, Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on September 28, 2023.
Victor Wicklund,
Deputy Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2023-22070 Filed 10-4-23; 8:45 am]
BILLING CODE 4910-13-P