Airworthiness Directives; Saab AB, Support and Services (Formerly Known as Saab AB, Saab Aeronautics) Airplanes, 39794-39796 [2023-12927]

Agencies

• Federal Aviation Administration
• DEPARTMENT OF TRANSPORTATION

[Federal Register Volume 88, Number 117 (Tuesday, June 20, 2023)]
[Proposed Rules]
[Pages 39794-39796]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-12927]


========================================================================
Proposed Rules
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains notices to the public of 
the proposed issuance of rules and regulations. The purpose of these 
notices is to give interested persons an opportunity to participate in 
the rule making prior to the adoption of the final rules.

========================================================================


Federal Register / Vol. 88, No. 117 / Tuesday, June 20, 2023 / 
Proposed Rules

[[Page 39794]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2023-1215; Project Identifier MCAI-2023-00196-T]
RIN 2120-AA64


Airworthiness Directives; Saab AB, Support and Services (Formerly 
Known as Saab AB, Saab Aeronautics) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Saab AB, Support and Services Model 340A (SAAB/SF340A) and 
SAAB 340B airplanes. This proposed AD was prompted by reports of a high 
number of events related to stall warnings upon landing, following 
introduction of the ice speed function within the stall warning system. 
This proposed AD would require modification of the stall warning/
identification system, as specified in a European Union Aviation Safety 
Agency (EASA) AD, which is proposed for incorporation by reference 
(IBR). The FAA is proposing this AD to address the unsafe condition on 
these products.

DATES: The FAA must receive comments on this proposed AD by August 4, 
2023.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2023-1215; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For EASA material that is proposed for IBR in this NPRM, 
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone 
+49 221 8999 000; email [email protected]; website easa.europa.eu. You 
may find this material on the EASA website at ad.easa.europa.eu. It is 
also available at regulations.gov under Docket No. FAA-2023-1215.
     You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Shahram Daneshmandi, Aviation Safety 
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone 206-231-3220; email [email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2023-1215; Project Identifier 
MCAI-2023-00196-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Shahram Daneshmandi, Aviation Safety Engineer, FAA, 1600 Stewart 
Avenue, Suite 410, Westbury, NY 11590; telephone 206-231-3220; email 
[email protected]. Any commentary that the FAA receives which 
is not specifically designated as CBI will be placed in the public 
docket for this rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2022-0216R1, dated February 1, 2023; 
corrected February 2, 2023 (EASA AD 2022-0216R1) (also referred to as 
the MCAI), to correct an unsafe condition for SAAB SF340A and SAAB 340B 
airplanes, all serial numbers, except those that have SAAB modification 
number 2650 (Canada Ice Speed Configuration) embodied. The MCAI states 
that following the introduction of the ice speed function within the 
SAAB 340 stall warning system, a high number of events have been 
reported related to stall warnings upon landing. Subsequent 
investigation determined that the margin to stall warning is lower when 
ice speed is ON than with ice speed OFF. This condition, if not 
corrected, could lead to inappropriate stall warnings during the 
landing phase

[[Page 39795]]

and result in increased pilot workload during a critical phase of 
flight.
    The FAA is issuing this AD to address the unsafe condition on these 
products.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2023-1215.

Related Service Information Under 1 CFR Part 51

    EASA AD 2022-0216R1 specifies procedures for modifying the stall 
warning/identification system to introduce an ice speed cancel logic. 
This material is reasonably available because the interested parties 
have access to it through their normal course of business or by the 
means identified in ADDRESSES.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with the State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
described above. The FAA is issuing this NPRM after determining that 
the unsafe condition described previously is likely to exist or develop 
in other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2022-0216R1 described previously, except for any differences 
identified as exceptions in the regulatory text of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate EASA AD 2022-0216R1 by reference in the FAA 
final rule. This proposed AD would, therefore, require compliance with 
EASA AD 2022-0216R1 in its entirety through that incorporation, except 
for any differences identified as exceptions in the regulatory text of 
this proposed AD. Using common terms that are the same as the heading 
of a particular section in EASA AD 2022-0216R1 does not mean that 
operators need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2022-
0216R1. Service information required by EASA AD 2022-0216R1 for 
compliance will be available at regulations.gov under Docket No. FAA-
2023-1215 after the FAA final rule is published.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 79 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
             Labor cost                Parts cost           Cost per product           Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Up to 30 work-hours x $85 per hour           $7,900  Up to $10,450................  Up to $825,550.
 = $2,550.
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Saab AB, Support and Services (Formerly Known as Saab AB, Saab 
Aeronautics): Docket No. FAA-2023-1215; Project Identifier MCAI-
2023-00196-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by August 4, 2023.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Saab AB, Support and Services (formerly known 
as Saab AB, Saab Aeronautics) Model 340A (SAAB/SF340A) and SAAB 340B 
airplanes, certificated in any category, as identified in European 
Union Aviation Safety Agency (EASA) AD 2022-0216R1, dated February 
1, 2023; corrected February 2, 2023 (EASA AD 2022-0216R1).

[[Page 39796]]

(d) Subject

    Air Transport Association (ATA) of America Code 27, Flight 
controls.

(e) Unsafe Condition

    This AD was prompted by reports of a high number of events 
related to stall warnings upon landing, following introduction of 
the ice speed function within the stall warning system. The FAA is 
issuing this AD to address a margin to stall warning that is lower 
when ice speed is ON than with ice speed OFF. The unsafe condition, 
if not addressed, could lead to inappropriate stall warnings during 
the landing phase and result in increased pilot workload during a 
critical phase of flight.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2022-0216R1.

(h) Exceptions to EASA AD 2022-0216R1

    (1) Where EASA AD 2022-0216R1 refers to November 16, 2022 (the 
effective date of EASA AD 2022-0216), this AD requires using the 
effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2022-0216R1 does not 
apply to this AD.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the International 
Validation Branch, send it to the attention of the person identified 
in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Saab AB, Support and Services' 
EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.

(j) Additional Information

    For more information about this AD, contact Shahram Daneshmandi, 
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 206-231-3220; email 
[email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2022-0216R1, 
dated February 1, 2023; corrected February 2, 2023.
    (ii) [Reserved]
    (3) For EASA AD 2022-0216R1, contact EASA, Konrad-Adenauer-Ufer 
3, 50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this EASA 
AD on the EASA website at ad.easa.europa.eu.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email [email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on June 12, 2023.
Ross Landes,
Deputy Director for Regulatory Operations, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2023-12927 Filed 6-16-23; 8:45 am]
BILLING CODE 4910-13-P