Airworthiness Directives; Airbus SAS Airplanes, 12143-12146 [2023-04020]

Agencies

• Federal Aviation Administration
• DEPARTMENT OF TRANSPORTATION

[Federal Register Volume 88, Number 38 (Monday, February 27, 2023)]
[Rules and Regulations]
[Pages 12143-12146]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-04020]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2023-0174; Project Identifier MCAI-2023-00063-T; 
Amendment 39-22359; AD 2023-04-12]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

[[Page 12144]]

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by 
a determination that longitudinal sealing tape in the forward and aft 
cargo compartments had migrated from its original position, which could 
affect the fire extinguishing system efficiency in the cargo 
compartments. This AD requires repetitive detailed inspection of the 
affected parts, and, depending on findings, accomplishment of 
applicable corrective action, as specified in a European Union Aviation 
Safety Agency (EASA) AD, which is incorporated by reference. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD is effective March 14, 2023.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of March 14, 
2023.
    The FAA must receive comments on this AD by April 13, 2023.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2023-0174; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For material incorporated by reference in this AD, contact 
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; website easa.europa.eu. You may 
find this material on the EASA website at ad.easa.europa.eu.
     You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available at 
regulations.gov under Docket No. FAA-2023-0174.

FOR FURTHER INFORMATION CONTACT: Dat Le, Aerospace Engineer, Large 
Aircraft Section, FAA, International Validation Branch, 2200 South 
216th St., Des Moines, WA 98198; telephone 516-228-7317; email 
[email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    The FAA invites you to send any written data, views, or arguments 
about this final rule. Send your comments to an address listed under 
ADDRESSES. Include ``Docket No. FAA-2023-0174; Project Identifier MCAI-
2023-00063-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the final rule, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this final rule because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this final rule.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this AD contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this AD, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this AD. Submissions containing CBI should be sent to Dat Le, 
Aerospace Engineer, Large Aircraft Section, FAA, International 
Validation Branch, 2200 South 216th St., Des Moines, WA 98198; 
telephone 516-228-7317; email [email protected]. Any commentary that the 
FAA receives which is not specifically designated as CBI will be placed 
in the public docket for this rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2023-0011, dated January 17, 2023 
(EASA AD 2023-0011) (also referred to as the MCAI), to correct an 
unsafe condition for all Airbus SAS Model A350-941 and -1041 airplanes. 
The MCAI states that longitudinal sealing tape in the forward and aft 
cargo compartments had migrated from its original position, possibly 
due to relative movement between the cargo floor panels and the cargo 
loading system, combined with compression of the tape. One function of 
the cargo floor panel sealing is as a contributor to the tightness of 
the lower cargo compartment floor panels, which provide an enclosed 
area to maintain halon concentration in the event of a fire. This 
condition, if not addressed, could affect the fire extinguishing system 
efficiency in the cargo compartments, possibly resulting in failure of 
the system to contain a cargo compartment fire or permanently 
extinguish the fire.
    The FAA is issuing this AD to address the unsafe condition on these 
products.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2023-0174.

Related Service Information Under 1 CFR Part 51

    EASA AD 2023-0011 specifies procedures for repetitive detailed 
inspections of the affected parts (i.e., cargo sealing tapes installed 
between the cargo floor panels and the cargo loading system in 
longitudinal direction, in the forward and aft cargo compartment area) 
for complete or partial migration of the cargo sealing tape and to 
determine if there are any repairs on the tape; for partially migrated 
tape, measuring the maximum migration of the tape; for repaired tape, 
inspecting for incorrect seating/condition of the tape and incorrect 
sealant condition; and applicable corrective action if any 
discrepancies are found (i.e., any cargo sealing tape that has migrated 
more than 11 millimeters, complete migration of the tape, incorrect 
seating/condition of the tape in repaired areas, and incorrect sealant 
condition in repaired areas). Corrective actions include repairing the 
tape and sealant. This material is reasonably available because the 
interested parties have access to it through their normal course of 
business

[[Page 12145]]

or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
described above. The FAA is issuing this AD after determining that the 
unsafe condition described previously is likely to exist or develop on 
other products of the same type design.

Requirements of This AD

    This AD requires accomplishing the actions specified in EASA AD 
2023-0011 described previously, except for any differences identified 
as exceptions in the regulatory text of this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, 
EASA AD 2023-0011 is incorporated by reference in this AD. This AD 
requires compliance with EASA AD 2023-0011 in its entirety through that 
incorporation, except for any differences identified as exceptions in 
the regulatory text of this AD. Using common terms that are the same as 
the heading of a particular section in EASA AD 2023-0011 does not mean 
that operators need comply only with that section. For example, where 
the AD requirement refers to ``all required actions and compliance 
times,'' compliance with this AD requirement is not limited to the 
section titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 
2023-0011. Service information required by EASA AD 2023-0011 for 
compliance will be available at regulations.gov under Docket No. FAA-
2023-0174 after this AD is published.

Interim Action

    The FAA considers that this AD is an interim action. If final 
action is later identified, the FAA might consider further rulemaking 
then.

FAA's Justification and Determination of the Effective Date

    Section 553(b)(3)(B) of the Administrative Procedure Act (APA) (5 
U.S.C. 551 et seq.) authorizes agencies to dispense with notice and 
comment procedures for rules when the agency, for ``good cause,'' finds 
that those procedures are ``impracticable, unnecessary, or contrary to 
the public interest.'' Under this section, an agency, upon finding good 
cause, may issue a final rule without providing notice and seeking 
comment prior to issuance. Further, section 553(d) of the APA 
authorizes agencies to make rules effective in less than thirty days, 
upon a finding of good cause.
    An unsafe condition exists that requires the immediate adoption of 
this AD without providing an opportunity for public comments prior to 
adoption. The FAA has found that the risk to the flying public 
justifies forgoing notice and comment prior to adoption of this rule 
because migration of the sealing tape can affect the tightness of the 
cargo compartment floor panels, which provide an enclosed area to 
maintain halon concentration in the event of a fire. Migration of the 
sealing tape in the forward and aft cargo compartments could affect the 
fire extinguishing system efficiency in the cargo compartments and 
possibly result in failure of the system to contain a cargo compartment 
fire or permanently extinguish the fire. In addition, the compliance 
time for the required action is shorter than the time necessary for the 
public to comment and for publication of the final rule. Accordingly, 
notice and opportunity for prior public comment are impracticable and 
contrary to the public interest pursuant to 5 U.S.C. 553(b)(3)(B).
    In addition, the FAA finds that good cause exists pursuant to 5 
U.S.C. 553(d) for making this amendment effective in less than 30 days, 
for the same reasons the FAA found good cause to forgo notice and 
comment.

Regulatory Flexibility Act (RFA)

    The requirements of the RFA do not apply when an agency finds good 
cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and 
comment. Because the FAA has determined that it has good cause to adopt 
this rule without notice and comment, RFA analysis is not required.

Costs of Compliance

    The FAA estimates that this AD affects 31 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
               Labor cost                   Parts cost         Cost per product         Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Up to 1 work-hour x $85 per hour = $85..              $0  Up to $85.................  Up to $2,635.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition actions that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need these on-condition actions:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
           Labor cost                 Parts cost       Cost per product
------------------------------------------------------------------------
Up to 2 work-hours x $85 per      Up to $10.........  Up to $180.
 hour = $170.
------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA

[[Page 12146]]

with promoting safe flight of civil aircraft in air commerce by 
prescribing regulations for practices, methods, and procedures the 
Administrator finds necessary for safety in air commerce. This 
regulation is within the scope of that authority because it addresses 
an unsafe condition that is likely to exist or develop on products 
identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2023-04-12 Airbus SAS: Amendment 39-22359; Docket No. FAA-2023-0174; 
Project Identifier MCAI-2023-00063-T.

(a) Effective Date

    This airworthiness directive (AD) is effective March 14, 2023.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Airbus SAS Model A350-941 and -1041 
airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Unsafe Condition

    This AD was prompted by a determination that longitudinal 
sealing tape in the forward and aft cargo compartments had migrated 
from its original position. The FAA is issuing this AD to address 
migration of the tape, which can affect the tightness of the cargo 
compartment floor panels that provide an enclosed area to maintain 
halon concentration in the event of a fire. This condition, if not 
addressed, could affect the fire extinguishing system efficiency in 
the cargo compartments, possibly resulting in failure of the system 
to contain a cargo compartment fire or permanently extinguish a 
fire.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2023-0011, dated January 17, 2023 (EASA AD 2023-0011).

(h) Exceptions to EASA AD 2023-0011

    (1) Where EASA AD 2023-0011 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) Where paragraph (2) of EASA AD 2023-0011 specifies 
accomplishing corrective actions if ``discrepancies, as identified 
in the AOT'' are found, for this AD, discrepancies is defined as 
cargo sealing tape that has migrated more than 11 millimeters, 
complete migration of the tape as shown in Condition B of the 
service information reference in EASA 2023-0011, incorrect seating/
condition of the tape in repaired areas, and incorrect sealant 
condition in repaired areas.
    (3) This AD does not adopt the ``Remarks'' section of EASA AD 
2023-0011.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the International 
Validation Branch, send it to the attention of the person identified 
in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information referenced 
in EASA AD 2023-0011 contains paragraphs that are labeled as RC, the 
instructions in RC paragraphs, including subparagraphs under an RC 
paragraph, must be done to comply with this AD; any paragraphs, 
including subparagraphs under those paragraphs, that are not 
identified as RC are recommended. The instructions in paragraphs, 
including subparagraphs under those paragraphs, not identified as RC 
may be deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the instructions identified as RC can 
be done and the airplane can be put back in an airworthy condition. 
Any substitutions or changes to instructions identified as RC 
require approval of an AMOC.

(j) Additional Information

    For more information about this AD, contact Dat Le, Aerospace 
Engineer, Large Aircraft Section, FAA, International Validation 
Branch, 2200 South 216th St., Des Moines, WA 98198; telephone 516-
228-7317; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2023-0011, 
dated January 17, 2023.
    (ii) [Reserved]
    (3) For EASA AD 2023-0011, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this EASA 
AD on the EASA website at ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on February 17, 2023.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2023-04020 Filed 2-23-23; 8:45 am]
BILLING CODE 4910-13-P