Airworthiness Directives; Dassault Aviation Airplanes, 76151-76154 [2022-26937]

Download as PDF Federal Register / Vol. 87, No. 238 / Tuesday, December 13, 2022 / Proposed Rules (3) Where the Action paragraph of CAAI AD ISR I–57–2021–12–4 refers to certain service information, replace the text ‘‘Gulfstream Service Bulletin No. 200–57– 426, dated January 01, 2022, or later approved revision,’’ with ‘‘Gulfstream Service Bulletin No. 200–57–426, Revision 1, dated June 16, 2022, or later approved revision.’’ (4) Where the service information specified in CAAI AD ISR I–57–2021–12–4 specifies to report to Gulfstream if ‘‘cracks were discovered’’ and ‘‘for any fairing installation location with one or more grid squares with thickness reduction of greater than 10%,’’ for this AD, cracks and fairing installation locations with one or more grid squares with thickness reduction of greater than 10% must be repaired before further flight using a method approved by the Manager, International Validation Branch, FAA; or CAAI; or CAAI’s authorized Designee. If approved by the authorized Designee, the approval must include the Designee’s authorized signature. (i) No Reporting Requirement Although the service information referenced in CAAI AD ISR I–57–2021–12–4 specifies to submit certain information to the manufacturer, this AD does not include that requirement. lotter on DSK11XQN23PROD with PROPOSALS1 (j) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the International Validation Branch, send it to the attention of the person identified in paragraph (k) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or CAAI; or CAAI’s authorized Designee. If approved by the CAAI Designee, the approval must include the Designee’s authorized signature. (k) Additional Information For more information about this AD, contact Dan Rodina, Aerospace Engineer, Large Aircraft Section, FAA, International Validation Branch, FAA, 2200 South 216th Street, Des Moines, WA 98198; telephone 206–231–3225; email dan.rodina@faa.gov. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. VerDate Sep<11>2014 16:31 Dec 12, 2022 Jkt 259001 (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) Civil Aviation Authority of Israel (CAAI) AD ISR I–57–2021–12–4, dated January 1, 2022. (ii) [Reserved] (3) For CAAI AD ISR I–57–2021–12–4, contact Civil Aviation Authority of Israel (CAAI), P.O. Box 1101, Golan Street, Airport City, 70100, Israel; telephone 972–3– 9774665; fax 972–3–9774592; email aip@ mot.gov.il. You may find this CAAI AD on the CAAI website at caa.gov.il. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. (5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email fr.inspection@nara.gov, or go to: www.archives.gov/federal-register/cfr/ibrlocations.html. Issued on December 7, 2022. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022–26974 Filed 12–12–22; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2022–1579; Project Identifier MCAI–2022–00903–T] RIN 2120–AA64 Airworthiness Directives; Dassault Aviation Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: The FAA proposes to supersede Airworthiness Directive (AD) 2021–09–12, which applies to certain Dassault Aviation Model FALCON 7X airplanes. AD 2021–09–12 requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2021–09–12, the FAA has determined that new or more restrictive airworthiness limitations are necessary. This proposed AD would continue to require the actions in AD 2021–09–12 and require revising the existing maintenance or inspection program, as applicable, to incorporate additional new or more restrictive SUMMARY: PO 00000 Frm 00025 Fmt 4702 Sfmt 4702 76151 airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products. DATES: The FAA must receive comments on this proposed AD by January 27, 2023. ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE, Washington, DC 20590. • Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA–2022–1579; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above. Material Incorporated by Reference: • For material that is proposed for IBR in this NPRM, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; website easa.europa.eu. You may find this material on the EASA website at ad.easa.europa.eu. It is also available at regulations.gov under Docket No. FAA– 2022–1579. • You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, Large Aircraft Section, International Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206–231–3226; email tom.rodriguez@faa.gov. SUPPLEMENTARY INFORMATION: Comments Invited The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send E:\FR\FM\13DEP1.SGM 13DEP1 76152 Federal Register / Vol. 87, No. 238 / Tuesday, December 13, 2022 / Proposed Rules your comments to an address listed under ADDRESSES. Include ‘‘Docket No. FAA–2022–1579; Project Identifier MCAI–2022–00903–T’’ at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this proposal because of those comments. Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to regulations.gov, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM. Confidential Business Information CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as ‘‘PROPIN.’’ The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Tom Rodriguez, Aerospace Engineer, Large Aircraft Section, International Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206–231–3226; email tom.rodriguez@ faa.gov. Any commentary that the FAA receives that is not specifically designated as CBI will be placed in the public docket for this rulemaking. lotter on DSK11XQN23PROD with PROPOSALS1 Background The FAA issued AD 2021–09–12, Amendment 39–21526 (86 FR 23593, May 4, 2021) (AD 2021–09–12), for certain Dassault Aviation Model FALCON 7X airplanes. AD 2021–09–12 was prompted by MCAI originated by EASA, which is the Technical Agent for the Member States of the European Union. EASA issued AD 2020–0214, dated October 6, 2020 (EASA AD 2020– 0214) (which corresponds to FAA AD VerDate Sep<11>2014 16:31 Dec 12, 2022 Jkt 259001 2021–09–12), to correct an unsafe condition. AD 2021–09–12 requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA issued AD 2021– 09–12 to address reduced structural integrity and reduced control of airplanes due to the failure of system components. AD 2021–09–12 specifies that accomplishing the revision required by that AD terminates certain requirements of AD 2014–16–23, Amendment 39–17947 (79 FR 52545, September 4, 2014) (AD 2014–16–23). Actions Since AD 2021–09–12 Was Issued Since the FAA issued AD 2021–09– 12, EASA superseded EASA AD 2020– 0214 and issued EASA AD 2022–0142, dated July 7, 2022 (EASA AD 2022– 0142) (referred to after this as the MCAI), for all Dassault Aviation Model FALCON 7X airplanes. The MCAI states that new or more restrictive airworthiness limitations have been issued. Airplanes with an original airworthiness certificate or original export certificate of airworthiness issued after June 7, 2021 must comply with the airworthiness limitations specified as part of the approved type design and referenced on the type certificate data sheet; this proposed AD therefore does not include those airplanes in the applicability. The FAA is proposing this AD to address reduced structural integrity and reduced control of airplanes due to the failure of system components. You may examine the MCAI in the AD docket at regulations.gov under Docket No. FAA– 2022–1579. Related Service Information Under 1 CFR Part 51 The FAA reviewed EASA AD 2022– 0142. This service information specifies new or more restrictive airworthiness limitations for airplane structures and safe life limits. This proposed AD would also require EASA AD 2020–0214, dated October 6, 2020, which the Director of the Federal Register approved for incorporation by reference as of June 8, 2021 (86 FR 23593, May 4, 2021). This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in ADDRESSES. FAA’s Determination This product has been approved by the aviation authority of another PO 00000 Frm 00026 Fmt 4702 Sfmt 4702 country and is approved for operation in the United States. Pursuant to the FAA’s bilateral agreement with the State of Design Authority, it has notified the FAA of the unsafe condition described in the MCAI described above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop in other products of the same type design. Proposed AD Requirements in This NPRM This proposed AD would retain certain requirements of AD 2021–09–12. This proposed AD would also require revising the existing maintenance or inspection program, as applicable, to incorporate additional new or more restrictive airworthiness limitations, which are specified in EASA AD 2022– 0142 already described, as proposed for incorporation by reference. Any differences with EASA AD 2022–0142 are identified as exceptions in the regulatory text of this AD. This proposed AD would require revisions to certain operator maintenance documents to include new actions (e.g., inspections) and Critical Design Configuration Control Limitations (CDCCLs). Compliance with these actions and CDCCLs is required by 14 CFR 91.403(c). For airplanes that have been previously modified, altered, or repaired in the areas addressed by this proposed AD, the operator may not be able to accomplish the actions described in the revisions. In this situation, to comply with 14 CFR 91.403(c), the operator must request approval for an alternative method of compliance (AMOC) according to paragraph (n)(1) of this proposed AD. Explanation of Required Compliance Information In the FAA’s ongoing efforts to improve the efficiency of the AD process, the FAA developed a process to use some civil aviation authority (CAA) ADs as the primary source of information for compliance with requirements for corresponding FAA ADs. The FAA has been coordinating this process with manufacturers and CAAs. As a result, the FAA proposes to retain the IBR of EASA AD 2020–0214 and incorporate EASA AD 2022–0142 by reference in the FAA final rule. This proposed AD would, therefore, require compliance with EASA AD 2022–0142 and EASA AD 2020–0214 through that incorporation, except for any differences identified as exceptions in the regulatory text of this proposed AD. Using common terms that are the same as the heading of a particular section in E:\FR\FM\13DEP1.SGM 13DEP1 Federal Register / Vol. 87, No. 238 / Tuesday, December 13, 2022 / Proposed Rules EASA AD 2022–0142 or EASA AD 2020–0214 does not mean that operators need comply only with that section. For example, where the AD requirement refers to ‘‘all required actions and compliance times,’’ compliance with this AD requirement is not limited to the section titled ‘‘Required Action(s) and Compliance Time(s)’’ in EASA AD 2022–0142 or EASA AD 2020–0214. Service information required by EASA AD 2022–0142 and EASA AD 2020– 0214 for compliance will be available at regulations.gov by searching for and locating Docket No. FAA–2022–1579 after the FAA final rule is published. lotter on DSK11XQN23PROD with PROPOSALS1 Airworthiness Limitation ADs Using the New Process The FAA’s process of incorporating by reference MCAI ADs as the primary source of information for compliance with corresponding FAA ADs has been limited to certain MCAI ADs (primarily those with service bulletins as the primary source of information for accomplishing the actions required by the FAA AD). However, the FAA is now expanding the process to include MCAI ADs that require a change to airworthiness limitation documents, such as airworthiness limitation sections. For these ADs that incorporate by reference an MCAI AD that changes airworthiness limitations, the FAA requirements are unchanged. Operators must revise the existing maintenance or inspection program, as applicable, to incorporate the information specified in the new airworthiness limitation document. The airworthiness limitations must be followed according to 14 CFR 91.403(c) and 91.409(e). The previous format of the airworthiness limitation ADs included a paragraph that specified that no alternative actions (e.g., inspections), intervals, or CDCCLs may be used unless the actions, intervals, and CDCCLs are approved as an AMOC in accordance with the procedures specified in the AMOCs paragraph under ‘‘Additional AD Provisions.’’ This new format includes a ‘‘New Provisions for Alternative Actions, Intervals, and CDCCLs’’ paragraph that does not specifically refer to AMOCs, but operators may still request an AMOC to use an alternative action, interval, or CDCCL. Costs of Compliance The FAA estimates that this AD, if adopted as proposed, would affect 122 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD: VerDate Sep<11>2014 16:31 Dec 12, 2022 Jkt 259001 The FAA estimates the total cost per operator for the retained actions from AD 2021–09–12 to be $7,650 (90 workhours × $85 per work-hour). The FAA has determined that revising the existing maintenance or inspection program takes an average of 90 workhours per operator, although the agency recognizes that this number may vary from operator to operator. Since operators incorporate maintenance or inspection program changes for their affected fleet(s), the FAA has determined that a per-operator estimate is more accurate than a per-airplane estimate. The FAA estimates the total cost per operator for the new proposed actions to be $7,650 (90 work-hours × $85 per work-hour). List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 ■ Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. ■ The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Would not affect intrastate aviation in Alaska, and (3) Would not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. PO 00000 Frm 00027 Fmt 4702 Sfmt 4702 [Amended] 2. The FAA amends § 39.13 by: a. Removing Airworthiness Directive (AD) 2021–09–12, Amendment 39– 21526 (86 FR 23593, May 4, 2021); and ■ b. Adding the following new AD: Authority for This Rulemaking Regulatory Findings 76153 Dassault Aviation: Docket No. FAA–2022– 1579; Project Identifier MCAI–2022– 00903–T. (a) Comments Due Date The FAA must receive comments on this airworthiness directive (AD) by January 27, 2023. (b) Affected ADs (1) This AD replaces AD 2021–09–12, Amendment 39–21526 (86 FR 23593, May 4, 2021) (AD 2021–09–12). (2) This AD affects AD 2014–16–23, Amendment 39–17947 (79 FR 52545, September 4, 2014) (AD 2014–16–23). (c) Applicability This AD applies to Dassault Aviation Model FALCON 7X airplanes, certificated in any category, with an original airworthiness certificate or original export certificate of airworthiness issued on or before June 7, 2021. Note 1 to paragraph (c): Model FALCON 7X airplanes with modification M1000 incorporated are commonly referred to as ‘‘Model FALCON 8X’’ airplanes as a marketing designation. (d) Subject Air Transport Association (ATA) of America Code 05, Time Limits/Maintenance Checks. (e) Unsafe Condition This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address reduced structural integrity and reduced control of airplanes due to the failure of system components. (f) Compliance Comply with this AD within the compliance times specified, unless already done. E:\FR\FM\13DEP1.SGM 13DEP1 76154 Federal Register / Vol. 87, No. 238 / Tuesday, December 13, 2022 / Proposed Rules (g) Retained Revision of the Existing Maintenance or Inspection Program, With No Changes This paragraph restates the requirements of paragraph (j) of AD 2021–09–12, with no changes. For airplanes with an original airworthiness certificate or original export certificate of airworthiness issued on or before June 1, 2020, except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2020–0214, dated October 6, 2020 (EASA AD 2020–0214). Accomplishing the revision of the existing maintenance or inspection program required by paragraph (j) of this AD terminates the requirements of this paragraph. lotter on DSK11XQN23PROD with PROPOSALS1 (h) Retained Exceptions to EASA AD 2020– 0214, With No Changes This paragraph restates the exceptions specified in paragraph (k) of AD 2021–09–12, With no changes. (1) The requirements specified in paragraphs (1) and (2) of EASA AD 2020– 0214 do not apply to this AD. (2) Paragraph (3) of EASA AD 2020–0214 specifies revising ‘‘the approved AMP’’ within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, to incorporate the ‘‘limitations, tasks and associated thresholds and intervals’’ specified in paragraph (3) of EASA AD 2020–0214 within 90 days after June 8, 2021 (the effective date of this AD 2021–09– 12). (3) The initial compliance time for doing the tasks specified in paragraph (3) of EASA AD 2020–0214 is at the applicable ‘‘associated thresholds’’ specified in paragraph (3) of EASA AD 2020–0214, or within 90 days after June 8, 2021 (the effective date of this AD 2021–09–12), whichever occurs later. (4) The provisions specified in paragraphs (4) and (5) of EASA AD 2019–0257 do not apply to this AD. (5) The ‘‘Remarks’’ section of EASA AD 2020–0214 does not apply to this AD. (i) Retained Restrictions on Alternative Actions, Intervals, and Critical Design Configuration Control Limitations (CDCCLs), With a New Exception This paragraph restates the requirements of paragraph (l) of AD 2021–09–12, with a new exception. Except as required by paragraph (j) of this AD, after the maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections), intervals, or CDCCLs are allowed unless they are approved as specified in the provisions of the ‘‘Ref. Publications’’ section of EASA AD 2020–0214. (j) New Revision of the Existing Maintenance or Inspection Program Except as specified in paragraph (k) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2022–0142, dated July 7, 2022 (EASA AD 2022–0142). VerDate Sep<11>2014 16:31 Dec 12, 2022 Jkt 259001 Accomplishing the revision of the existing maintenance or inspection program required by this paragraph terminates the requirements of paragraph (g) of this AD. (k) Exceptions to EASA AD 2022–0142 (1) The requirements specified in paragraphs (1) and (2) of EASA AD 2022– 0142 do not apply to this AD. (2) Paragraph (3) of EASA AD 2022–0142 specifies revising ‘‘the approved AMP’’ within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, within 90 days after the effective date of this AD. (3) The initial compliance time for doing the tasks specified in paragraph (3) of EASA AD 2022–0142 is at the applicable ‘‘limitations’’ and ‘‘associated thresholds’’ as incorporated by the requirements of paragraph (3) of EASA AD 2022–0142, or within 90 days after the effective date of this AD, whichever occurs later. (4) The provisions specified in paragraphs (4) and (5) of EASA AD 2022–0142 do not apply to this AD. (5) The ‘‘Remarks’’ section of EASA AD 2022–0142 does not apply to this AD. (l) New Provisions for Alternative Actions, Intervals, and CDCCLs After the existing maintenance or inspection program has been revised as required by paragraph (j) of this AD, no alternative actions (e.g., inspections), intervals, and CDCCLs are allowed unless they are approved as specified in the provisions of the ‘‘Ref. Publications’’ section of EASA AD 2022–0142. (m) Terminating Action for Certain Requirements in AD 2014–16–23 Accomplishing the actions required by paragraphs (g) or (j) of this AD terminates the requirements of paragraph (q) of AD 2014– 16–23. (n) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the International Validation Branch, send it to the attention of the person identified in paragraph (o) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Dassault Aviation’s EASA Design Organization Approval (DOA). If approved by the DOA, PO 00000 Frm 00028 Fmt 4702 Sfmt 9990 the approval must include the DOAauthorized signature. (o) Additional Information For more information about this AD, contact Tom Rodriguez, Aerospace Engineer, Large Aircraft Section, International Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206–231–3226; email tom.rodriguez@ faa.gov. (p) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (3) The following service information was approved for IBR on [DATE 35 DAYS AFTER PUBLICATION OF THE FINAL RULE]. (i) European Union Aviation Safety Agency (EASA) AD 2022–0142, dated July 7, 2022. (ii) [Reserved] (4) The following service information was approved for IBR on June 8, 2021 (86 FR 23593, May 4, 2021). (i) European Union Aviation Safety Agency (EASA) AD 2020–0214, dated October 6, 2020. (ii) [Reserved] (5) For EASA ADs 2022–0142 and 2020– 0214, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; website easa.europa.eu. You may find these EASA ADs on the EASA website at ad.easa.europa.eu. (6) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. (7) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email fr.inspection@nara.gov, or go to: archives.gov/federal-register/cfr/ibrlocations.html. Issued on December 6, 2022. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022–26937 Filed 12–12–22; 8:45 am] BILLING CODE 4910–13–P E:\FR\FM\13DEP1.SGM 13DEP1

Agencies

[Federal Register Volume 87, Number 238 (Tuesday, December 13, 2022)]
[Proposed Rules]
[Pages 76151-76154]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-26937]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-1579; Project Identifier MCAI-2022-00903-T]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD) 
2021-09-12, which applies to certain Dassault Aviation Model FALCON 7X 
airplanes. AD 2021-09-12 requires revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations. Since the FAA issued AD 2021-09-
12, the FAA has determined that new or more restrictive airworthiness 
limitations are necessary. This proposed AD would continue to require 
the actions in AD 2021-09-12 and require revising the existing 
maintenance or inspection program, as applicable, to incorporate 
additional new or more restrictive airworthiness limitations, as 
specified in a European Union Aviation Safety Agency (EASA) AD, which 
is proposed for incorporation by reference (IBR). The FAA is proposing 
this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by January 27, 
2023.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2022-1579; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For material that is proposed for IBR in this NPRM, 
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone 
+49 221 8999 000; email [email protected]; website easa.europa.eu. You 
may find this material on the EASA website at ad.easa.europa.eu. It is 
also available at regulations.gov under Docket No. FAA-2022-1579.
     You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
Large Aircraft Section, International Validation Branch, FAA, 2200 
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3226; 
email [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send

[[Page 76152]]

your comments to an address listed under ADDRESSES. Include ``Docket 
No. FAA-2022-1579; Project Identifier MCAI-2022-00903-T'' at the 
beginning of your comments. The most helpful comments reference a 
specific portion of the proposal, explain the reason for any 
recommended change, and include supporting data. The FAA will consider 
all comments received by the closing date and may amend this proposal 
because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to Tom 
Rodriguez, Aerospace Engineer, Large Aircraft Section, International 
Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; 
telephone and fax 206-231-3226; email [email protected]. Any 
commentary that the FAA receives that is not specifically designated as 
CBI will be placed in the public docket for this rulemaking.

Background

    The FAA issued AD 2021-09-12, Amendment 39-21526 (86 FR 23593, May 
4, 2021) (AD 2021-09-12), for certain Dassault Aviation Model FALCON 7X 
airplanes. AD 2021-09-12 was prompted by MCAI originated by EASA, which 
is the Technical Agent for the Member States of the European Union. 
EASA issued AD 2020-0214, dated October 6, 2020 (EASA AD 2020-0214) 
(which corresponds to FAA AD 2021-09-12), to correct an unsafe 
condition.
    AD 2021-09-12 requires revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations. The FAA issued AD 2021-09-12 to 
address reduced structural integrity and reduced control of airplanes 
due to the failure of system components. AD 2021-09-12 specifies that 
accomplishing the revision required by that AD terminates certain 
requirements of AD 2014-16-23, Amendment 39-17947 (79 FR 52545, 
September 4, 2014) (AD 2014-16-23).

Actions Since AD 2021-09-12 Was Issued

    Since the FAA issued AD 2021-09-12, EASA superseded EASA AD 2020-
0214 and issued EASA AD 2022-0142, dated July 7, 2022 (EASA AD 2022-
0142) (referred to after this as the MCAI), for all Dassault Aviation 
Model FALCON 7X airplanes. The MCAI states that new or more restrictive 
airworthiness limitations have been issued.
    Airplanes with an original airworthiness certificate or original 
export certificate of airworthiness issued after June 7, 2021 must 
comply with the airworthiness limitations specified as part of the 
approved type design and referenced on the type certificate data sheet; 
this proposed AD therefore does not include those airplanes in the 
applicability.
    The FAA is proposing this AD to address reduced structural 
integrity and reduced control of airplanes due to the failure of system 
components. You may examine the MCAI in the AD docket at 
regulations.gov under Docket No. FAA-2022-1579.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed EASA AD 2022-0142. This service information 
specifies new or more restrictive airworthiness limitations for 
airplane structures and safe life limits.
    This proposed AD would also require EASA AD 2020-0214, dated 
October 6, 2020, which the Director of the Federal Register approved 
for incorporation by reference as of June 8, 2021 (86 FR 23593, May 4, 
2021).
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in ADDRESSES.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with the State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
described above. The FAA is issuing this NPRM after determining that 
the unsafe condition described previously is likely to exist or develop 
in other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would retain certain requirements of AD 2021-09-
12. This proposed AD would also require revising the existing 
maintenance or inspection program, as applicable, to incorporate 
additional new or more restrictive airworthiness limitations, which are 
specified in EASA AD 2022-0142 already described, as proposed for 
incorporation by reference. Any differences with EASA AD 2022-0142 are 
identified as exceptions in the regulatory text of this AD.
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections) and 
Critical Design Configuration Control Limitations (CDCCLs). Compliance 
with these actions and CDCCLs is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance (AMOC) according to 
paragraph (n)(1) of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to retain the IBR of EASA AD 2020-0214 and incorporate 
EASA AD 2022-0142 by reference in the FAA final rule. This proposed AD 
would, therefore, require compliance with EASA AD 2022-0142 and EASA AD 
2020-0214 through that incorporation, except for any differences 
identified as exceptions in the regulatory text of this proposed AD. 
Using common terms that are the same as the heading of a particular 
section in

[[Page 76153]]

EASA AD 2022-0142 or EASA AD 2020-0214 does not mean that operators 
need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2022-
0142 or EASA AD 2020-0214. Service information required by EASA AD 
2022-0142 and EASA AD 2020-0214 for compliance will be available at 
regulations.gov by searching for and locating Docket No. FAA-2022-1579 
after the FAA final rule is published.

Airworthiness Limitation ADs Using the New Process

    The FAA's process of incorporating by reference MCAI ADs as the 
primary source of information for compliance with corresponding FAA ADs 
has been limited to certain MCAI ADs (primarily those with service 
bulletins as the primary source of information for accomplishing the 
actions required by the FAA AD). However, the FAA is now expanding the 
process to include MCAI ADs that require a change to airworthiness 
limitation documents, such as airworthiness limitation sections.
    For these ADs that incorporate by reference an MCAI AD that changes 
airworthiness limitations, the FAA requirements are unchanged. 
Operators must revise the existing maintenance or inspection program, 
as applicable, to incorporate the information specified in the new 
airworthiness limitation document. The airworthiness limitations must 
be followed according to 14 CFR 91.403(c) and 91.409(e).
    The previous format of the airworthiness limitation ADs included a 
paragraph that specified that no alternative actions (e.g., 
inspections), intervals, or CDCCLs may be used unless the actions, 
intervals, and CDCCLs are approved as an AMOC in accordance with the 
procedures specified in the AMOCs paragraph under ``Additional AD 
Provisions.'' This new format includes a ``New Provisions for 
Alternative Actions, Intervals, and CDCCLs'' paragraph that does not 
specifically refer to AMOCs, but operators may still request an AMOC to 
use an alternative action, interval, or CDCCL.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 122 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:
    The FAA estimates the total cost per operator for the retained 
actions from AD 2021-09-12 to be $7,650 (90 work-hours x $85 per work-
hour).
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the agency recognizes that this number may vary from operator 
to operator. Since operators incorporate maintenance or inspection 
program changes for their affected fleet(s), the FAA has determined 
that a per-operator estimate is more accurate than a per-airplane 
estimate.
    The FAA estimates the total cost per operator for the new proposed 
actions to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by:
0
a. Removing Airworthiness Directive (AD) 2021-09-12, Amendment 39-21526 
(86 FR 23593, May 4, 2021); and
0
b. Adding the following new AD:

Dassault Aviation: Docket No. FAA-2022-1579; Project Identifier 
MCAI-2022-00903-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by January 27, 2023.

(b) Affected ADs

    (1) This AD replaces AD 2021-09-12, Amendment 39-21526 (86 FR 
23593, May 4, 2021) (AD 2021-09-12).
    (2) This AD affects AD 2014-16-23, Amendment 39-17947 (79 FR 
52545, September 4, 2014) (AD 2014-16-23).

(c) Applicability

    This AD applies to Dassault Aviation Model FALCON 7X airplanes, 
certificated in any category, with an original airworthiness 
certificate or original export certificate of airworthiness issued 
on or before June 7, 2021.
    Note 1 to paragraph (c): Model FALCON 7X airplanes with 
modification M1000 incorporated are commonly referred to as ``Model 
FALCON 8X'' airplanes as a marketing designation.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Unsafe Condition

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to address reduced structural integrity and reduced 
control of airplanes due to the failure of system components.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

[[Page 76154]]

(g) Retained Revision of the Existing Maintenance or Inspection 
Program, With No Changes

    This paragraph restates the requirements of paragraph (j) of AD 
2021-09-12, with no changes. For airplanes with an original 
airworthiness certificate or original export certificate of 
airworthiness issued on or before June 1, 2020, except as specified 
in paragraph (h) of this AD: Comply with all required actions and 
compliance times specified in, and in accordance with, European 
Union Aviation Safety Agency (EASA) AD 2020-0214, dated October 6, 
2020 (EASA AD 2020-0214). Accomplishing the revision of the existing 
maintenance or inspection program required by paragraph (j) of this 
AD terminates the requirements of this paragraph.

(h) Retained Exceptions to EASA AD 2020-0214, With No Changes

    This paragraph restates the exceptions specified in paragraph 
(k) of AD 2021-09-12, With no changes.
    (1) The requirements specified in paragraphs (1) and (2) of EASA 
AD 2020-0214 do not apply to this AD.
    (2) Paragraph (3) of EASA AD 2020-0214 specifies revising ``the 
approved AMP'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, to incorporate the ``limitations, tasks and 
associated thresholds and intervals'' specified in paragraph (3) of 
EASA AD 2020-0214 within 90 days after June 8, 2021 (the effective 
date of this AD 2021-09-12).
    (3) The initial compliance time for doing the tasks specified in 
paragraph (3) of EASA AD 2020-0214 is at the applicable ``associated 
thresholds'' specified in paragraph (3) of EASA AD 2020-0214, or 
within 90 days after June 8, 2021 (the effective date of this AD 
2021-09-12), whichever occurs later.
    (4) The provisions specified in paragraphs (4) and (5) of EASA 
AD 2019-0257 do not apply to this AD.
    (5) The ``Remarks'' section of EASA AD 2020-0214 does not apply 
to this AD.

(i) Retained Restrictions on Alternative Actions, Intervals, and 
Critical Design Configuration Control Limitations (CDCCLs), With a New 
Exception

    This paragraph restates the requirements of paragraph (l) of AD 
2021-09-12, with a new exception. Except as required by paragraph 
(j) of this AD, after the maintenance or inspection program has been 
revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections), intervals, or CDCCLs are allowed unless 
they are approved as specified in the provisions of the ``Ref. 
Publications'' section of EASA AD 2020-0214.

(j) New Revision of the Existing Maintenance or Inspection Program

    Except as specified in paragraph (k) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2022-0142, dated July 7, 2022 (EASA AD 
2022-0142). Accomplishing the revision of the existing maintenance 
or inspection program required by this paragraph terminates the 
requirements of paragraph (g) of this AD.

(k) Exceptions to EASA AD 2022-0142

    (1) The requirements specified in paragraphs (1) and (2) of EASA 
AD 2022-0142 do not apply to this AD.
    (2) Paragraph (3) of EASA AD 2022-0142 specifies revising ``the 
approved AMP'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, within 90 days after the effective date of this AD.
    (3) The initial compliance time for doing the tasks specified in 
paragraph (3) of EASA AD 2022-0142 is at the applicable 
``limitations'' and ``associated thresholds'' as incorporated by the 
requirements of paragraph (3) of EASA AD 2022-0142, or within 90 
days after the effective date of this AD, whichever occurs later.
    (4) The provisions specified in paragraphs (4) and (5) of EASA 
AD 2022-0142 do not apply to this AD.
    (5) The ``Remarks'' section of EASA AD 2022-0142 does not apply 
to this AD.

(l) New Provisions for Alternative Actions, Intervals, and CDCCLs

    After the existing maintenance or inspection program has been 
revised as required by paragraph (j) of this AD, no alternative 
actions (e.g., inspections), intervals, and CDCCLs are allowed 
unless they are approved as specified in the provisions of the 
``Ref. Publications'' section of EASA AD 2022-0142.

(m) Terminating Action for Certain Requirements in AD 2014-16-23

    Accomplishing the actions required by paragraphs (g) or (j) of 
this AD terminates the requirements of paragraph (q) of AD 2014-16-
23.

(n) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the International 
Validation Branch, send it to the attention of the person identified 
in paragraph (o) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Dassault Aviation's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.

(o) Additional Information

    For more information about this AD, contact Tom Rodriguez, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3226; email [email protected].

(p) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (3) The following service information was approved for IBR on 
[DATE 35 DAYS AFTER PUBLICATION OF THE FINAL RULE].
    (i) European Union Aviation Safety Agency (EASA) AD 2022-0142, 
dated July 7, 2022.
    (ii) [Reserved]
    (4) The following service information was approved for IBR on 
June 8, 2021 (86 FR 23593, May 4, 2021).
    (i) European Union Aviation Safety Agency (EASA) AD 2020-0214, 
dated October 6, 2020.
    (ii) [Reserved]
    (5) For EASA ADs 2022-0142 and 2020-0214, contact EASA, Konrad-
Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; 
email [email protected]; website easa.europa.eu. You may find these 
EASA ADs on the EASA website at ad.easa.europa.eu.
    (6) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (7) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on December 6, 2022.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2022-26937 Filed 12-12-22; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.