Airworthiness Directives; The Boeing Company Airplanes, 73456-73458 [2022-26082]

Download as PDF 73456 Federal Register / Vol. 87, No. 229 / Wednesday, November 30, 2022 / Rules and Regulations for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (l)(1) of this AD. Information may be emailed to: 9ANM-Seattle-ACO-AMOC-Requests@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by The Boeing Company Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO Branch, FAA, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. (1) For more information about this AD, contact Kevin Nguyen, Aerospace Engineer, Propulsion Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206–231–3555; email: kevin.nguyen@faa.gov. (2) Service information identified in this AD that is not incorporated by reference is available at the addresses specified in paragraphs (m)(3) and (4) of this AD. lotter on DSK11XQN23PROD with RULES1 (m) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Boeing Alert Requirements Bulletin 777–28A0090 RB, dated March 30, 2021. (ii) [Reserved] (3) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110–SK57, Seal Beach, CA 90740–5600; telephone 562–797–1717; internet myboeingfleet.com. (4) You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, fr.inspection@nara.gov, or go to: www.archives.gov/federal-register/cfr/ibrlocations.html. 15:58 Nov 29, 2022 [FR Doc. 2022–26079 Filed 11–29–22; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2022–1059; Project Identifier AD–2022–00204–T; Amendment 39–22239; AD 2022–23–12] Jkt 259001 Airworthiness Directives; The Boeing Company Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Final rule. AGENCY: Frm 00024 Fmt 4700 Sfmt 4700 Nicole Tsang, Aerospace Engineer, Cabin Safety and Environmental Systems Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206– 231–3959; email: nicole.s.tsang@faa.gov. SUPPLEMENTARY INFORMATION: The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 747–100, 747– 100B, 747–100B SUD, 747–200B, 747– 200C, 747–200F, 747–300, 747–400, 747–400D, 747–400F, 747SR, and 747SP series airplanes. This AD was prompted by reports that high temperature composite trim air diffuser ducts (TADD) showed composite degradation and signs of hot air leakage. This AD requires a one-time low frequency eddy current (LFEC) inspection of certain center tank upper skin panels on the right and left side for any structural damage due to heat exposure, and repair if necessary. The FAA is issuing this AD to address the unsafe condition on these products. DATES: This AD is effective January 4, 2023. The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of January 4, 2023. ADDRESSES: AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA–2022–1059; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, any comments received, and other information. The address for Docket Operations is U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE, Washington, DC 20590. Material Incorporated by Reference: • For service information identified in this final rule, contact Boeing PO 00000 Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110–SK57, Seal Beach, CA 90740–5600; telephone 562–797–1717; internet myboeingfleet.com. • You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. It is also available at regulations.gov under Docket No. FAA– 2022–1059. FOR FURTHER INFORMATION CONTACT: RIN 2120–AA64 SUMMARY: (l) Related Information VerDate Sep<11>2014 Issued on November 1, 2022. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. Background The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to all The Boeing Company Model 747–100, 747–100B, 747–100B SUD, 747–200B, 747–200C, 747–200F, 747– 300, 747–400, 747–400D, 747–400F, 747SR, and 747SP series airplanes. The NPRM published in the Federal Register on September 8, 2022 (87 FR 54927). The NPRM was prompted by reports that high temperature composite TADD showed composite degradation and signs of hot air leakage. In the NPRM, the FAA proposed to require a one-time LFEC inspection of certain center tank upper skin panels on the right and left side for any structural damage due to heat exposure, and repair if necessary. The FAA is issuing this AD to address possible sustained hot air leakage from damaged TADDs, which could result in undetected damage to adjacent airframe structure. This condition, if not addressed, could lead to heat damage to the wing center section and adjacent structure and adversely affect the structural integrity of the airplane, resulting in the inability of the structure to carry limit load and the possible loss of continued safe flight and landing. Discussion of Final Airworthiness Directive Comments The FAA received comments from The Air Line Pilots Association, International (ALPA), who supported the NPRM without change. E:\FR\FM\30NOR1.SGM 30NOR1 Federal Register / Vol. 87, No. 229 / Wednesday, November 30, 2022 / Rules and Regulations Conclusion The FAA reviewed the relevant data, considered any comments received, and determined that air safety requires adopting this AD as proposed. Accordingly, the FAA is issuing this AD to address the unsafe condition on these products. Except for minor editorial changes, this AD is adopted as proposed in the NPRM. None of the changes will increase the economic burden on any operator. Related Service Information Under 1 CFR Part 51 The FAA reviewed Boeing Alert Requirements Bulletin 747–57A2370 RB, dated March 2, 2022. This service information specifies procedures for a one-time LFEC inspection for any structural damage due to heat exposure of the center tank upper skin panels on the right and left side between station (STA) 1100–1120, 1140–1160, and 1180–1200 bays outboard of left buttock 73457 line (LBL) 98 and right buttock line (RBL) 98 seat tracks, and repair. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in ADDRESSES. Costs of Compliance The FAA estimates that this AD affects 104 airplanes of U.S. registry. The FAA estimates the following costs to comply with this AD: ESTIMATED COSTS Action Labor cost LFEC inspection .............................................. 101 work-hours × $85 per hour = $8,585 ...... The FAA has received no definitive data on which to base the cost estimates for the on-condition repairs specified in this AD. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. lotter on DSK11XQN23PROD with RULES1 Regulatory Findings This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Will not affect intrastate aviation in Alaska, and VerDate Sep<11>2014 16:42 Nov 29, 2022 Jkt 259001 (3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive: ■ 2022–23–12 The Boeing Company: Amendment 39–22239; Docket No. FAA–2022–1059; Project Identifier AD– 2022–00204–T. (a) Effective Date This airworthiness directive (AD) is effective January 4, 2023. (b) Affected ADs None. (c) Applicability This AD applies to all The Boeing Company Model 747–100, 747–100B, 747– 100B SUD, 747–200B, 747–200C, 747–200F, 747–300, 747–400, 747–400D, 747–400F, 747SR, and 747SP series airplanes, certificated in any category. PO 00000 Frm 00025 Fmt 4700 Sfmt 4700 Cost per product Parts cost $0 $8,585 Cost on U.S. operators $892,840 (d) Subject Air Transport Association (ATA) of America Code 57, Wings. (e) Unsafe Condition This AD was prompted by reports that high temperature composite trim air diffuser ducts (TADD) showed composite degradation and signs of hot air leakage. The FAA is issuing this AD to address sustained hot air leakage from damaged TADDs that could result in undetected damage to adjacent airframe structure. This condition, if not addressed, could lead to heat damage to the wing center section and adjacent structure and adversely affect the structural integrity of the airplane, resulting in the inability of the structure to carry limit load and the possible loss of continued safe flight and landing. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Required Actions Except as specified by paragraph (h) of this AD: At the applicable times specified in the ‘‘Compliance’’ paragraph of Boeing Alert Requirements Bulletin 747–57A2370 RB, dated March 2, 2022, do all applicable actions identified in, and in accordance with, the Accomplishment Instructions of Boeing Alert Requirements Bulletin 747–57A2370 RB, dated March 2, 2022. Note 1 to paragraph (g): Guidance for accomplishing the actions required by this AD can be found in Boeing Alert Service Bulletin 747–57A2370, dated March 2, 2022, which is referred to in Boeing Alert Requirements Bulletin 747–57A2370 RB, dated March 2, 2022. (h) Exceptions To Service Information Specifications (1) Where the Compliance Time column of the table in the ‘‘Compliance’’ paragraph of Boeing Alert Requirements Bulletin 747– 57A2370 RB, dated March 2, 2022, uses the phrase ‘‘the original issue date of Requirements Bulletin 747–57A2370 RB,’’ this AD requires using ‘‘the effective date of this AD.’’ E:\FR\FM\30NOR1.SGM 30NOR1 73458 Federal Register / Vol. 87, No. 229 / Wednesday, November 30, 2022 / Rules and Regulations (2) Where Boeing Alert Requirements Bulletin 747–57A2370 RB, dated March 2, 2022, specifies contacting Boeing for repair instructions: This AD requires doing the repair before further flight using a method approved in accordance with the procedures specified in paragraph (i) of this AD. (i) Alternative Methods of Compliance (AMOCs) (1) The Manager, Seattle ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-ANMSeattle-ACO-AMOC-Requests@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by The Boeing Company Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO Branch, FAA, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. (j) Related Information For more information about this AD, contact Nicole Tsang, Aerospace Engineer, Cabin Safety and Environmental Systems, FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206–231–3959; email: nicole.s.tsang@faa.gov. (k) Material Incorporated by Reference lotter on DSK11XQN23PROD with RULES1 (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. VerDate Sep<11>2014 15:58 Nov 29, 2022 Jkt 259001 (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Boeing Alert Requirements Bulletin 747–57A2370 RB, dated March 2, 2022. (ii) [Reserved] (3) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110–SK57, Seal Beach, CA 90740–5600; telephone 562–797–1717; internet myboeingfleet.com. (4) You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, fr.inspection@nara.gov, or go to: www.archives.gov/federal-register/cfr/ibrlocations.html. Issued on November 3, 2022. Christina Underwood, Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service. [FR Doc. 2022–26082 Filed 11–29–22; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF THE TREASURY The final regulations (TD 9967) subject to this correction are issued under section 42 of the Internal Revenue Code. List of Subjects in 26 CFR Part 1 Income taxes, Reporting and recordkeeping requirements. Correction of Publication Accordingly, 26 CFR part 1 is corrected by making the following correcting amendment: PART 1—INCOME TAXES Paragraph 1. The authority citation for part 1 continues to read in part as follows: 26 CFR Part 1 Authority: 26 U.S.C. 7805 * * * [TD 9967] Par. 2. Section 1.42–19 is amended by revising table 2 to paragraph (e)(3)(i) to read as follows: ■ RIN 1545–BO92 Section 42, Low-Income Housing Credit Average Income Test Regulations; Correction Internal Revenue Service (IRS), Treasury. ACTION: Correcting amendments. AGENCY: Frm 00026 Background ■ Internal Revenue Service PO 00000 This document contains a correction to the final regulations (Treasury Decision 9967) published in the Federal Register on Wednesday, October 12, 2022. This correction includes final and temporary regulations setting forth guidance on the average income test for purposes of the low-income housing credit. DATES: These corrections are effective on November 30, 2022 and applicable on or after October 12, 2022. FOR FURTHER INFORMATION CONTACT: Concerning the regulations, Dillon Taylor at (202) 317–4137. SUPPLEMENTARY INFORMATION: SUMMARY: Fmt 4700 Sfmt 4700 § 1.42–19 Average income test. * * * * * * (e) * * (3) * * (i) * * * BILLING CODE 4830–01–P E:\FR\FM\30NOR1.SGM 30NOR1 *

Agencies

[Federal Register Volume 87, Number 229 (Wednesday, November 30, 2022)]
[Rules and Regulations]
[Pages 73456-73458]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-26082]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-1059; Project Identifier AD-2022-00204-T; 
Amendment 39-22239; AD 2022-23-12]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 
747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 
747SP series airplanes. This AD was prompted by reports that high 
temperature composite trim air diffuser ducts (TADD) showed composite 
degradation and signs of hot air leakage. This AD requires a one-time 
low frequency eddy current (LFEC) inspection of certain center tank 
upper skin panels on the right and left side for any structural damage 
due to heat exposure, and repair if necessary. The FAA is issuing this 
AD to address the unsafe condition on these products.

DATES: This AD is effective January 4, 2023.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of January 4, 
2023.

ADDRESSES: 
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2022-1059; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, any comments received, and other 
information. The address for Docket Operations is U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
    Material Incorporated by Reference:
     For service information identified in this final rule, 
contact Boeing Commercial Airplanes, Attention: Contractual & Data 
Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 
90740-5600; telephone 562-797-1717; internet myboeingfleet.com.
     You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available at 
regulations.gov under Docket No. FAA-2022-1059.

FOR FURTHER INFORMATION CONTACT: Nicole Tsang, Aerospace Engineer, 
Cabin Safety and Environmental Systems Section, FAA, Seattle ACO 
Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-
231-3959; email: [email protected].

SUPPLEMENTARY INFORMATION:

Background

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to all The Boeing Company 
Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 
747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series 
airplanes. The NPRM published in the Federal Register on September 8, 
2022 (87 FR 54927). The NPRM was prompted by reports that high 
temperature composite TADD showed composite degradation and signs of 
hot air leakage. In the NPRM, the FAA proposed to require a one-time 
LFEC inspection of certain center tank upper skin panels on the right 
and left side for any structural damage due to heat exposure, and 
repair if necessary. The FAA is issuing this AD to address possible 
sustained hot air leakage from damaged TADDs, which could result in 
undetected damage to adjacent airframe structure. This condition, if 
not addressed, could lead to heat damage to the wing center section and 
adjacent structure and adversely affect the structural integrity of the 
airplane, resulting in the inability of the structure to carry limit 
load and the possible loss of continued safe flight and landing.

Discussion of Final Airworthiness Directive

Comments

    The FAA received comments from The Air Line Pilots Association, 
International (ALPA), who supported the NPRM without change.

[[Page 73457]]

Conclusion

    The FAA reviewed the relevant data, considered any comments 
received, and determined that air safety requires adopting this AD as 
proposed. Accordingly, the FAA is issuing this AD to address the unsafe 
condition on these products. Except for minor editorial changes, this 
AD is adopted as proposed in the NPRM. None of the changes will 
increase the economic burden on any operator.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Boeing Alert Requirements Bulletin 747-57A2370 RB, 
dated March 2, 2022. This service information specifies procedures for 
a one-time LFEC inspection for any structural damage due to heat 
exposure of the center tank upper skin panels on the right and left 
side between station (STA) 1100-1120, 1140-1160, and 1180-1200 bays 
outboard of left buttock line (LBL) 98 and right buttock line (RBL) 98 
seat tracks, and repair. This service information is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in 
ADDRESSES.

Costs of Compliance

    The FAA estimates that this AD affects 104 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
               Action                         Labor cost            Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
LFEC inspection....................  101 work-hours x $85 per                 $0          $8,585        $892,840
                                      hour = $8,585.
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition repairs specified in this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2022-23-12 The Boeing Company: Amendment 39-22239; Docket No. FAA-
2022-1059; Project Identifier AD-2022-00204-T.

(a) Effective Date

    This airworthiness directive (AD) is effective January 4, 2023.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all The Boeing Company Model 747-100, 747-
100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 
747-400D, 747-400F, 747SR, and 747SP series airplanes, certificated 
in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 57, Wings.

(e) Unsafe Condition

    This AD was prompted by reports that high temperature composite 
trim air diffuser ducts (TADD) showed composite degradation and 
signs of hot air leakage. The FAA is issuing this AD to address 
sustained hot air leakage from damaged TADDs that could result in 
undetected damage to adjacent airframe structure. This condition, if 
not addressed, could lead to heat damage to the wing center section 
and adjacent structure and adversely affect the structural integrity 
of the airplane, resulting in the inability of the structure to 
carry limit load and the possible loss of continued safe flight and 
landing.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified by paragraph (h) of this AD: At the 
applicable times specified in the ``Compliance'' paragraph of Boeing 
Alert Requirements Bulletin 747-57A2370 RB, dated March 2, 2022, do 
all applicable actions identified in, and in accordance with, the 
Accomplishment Instructions of Boeing Alert Requirements Bulletin 
747-57A2370 RB, dated March 2, 2022.
    Note 1 to paragraph (g): Guidance for accomplishing the actions 
required by this AD can be found in Boeing Alert Service Bulletin 
747-57A2370, dated March 2, 2022, which is referred to in Boeing 
Alert Requirements Bulletin 747-57A2370 RB, dated March 2, 2022.

(h) Exceptions To Service Information Specifications

    (1) Where the Compliance Time column of the table in the 
``Compliance'' paragraph of Boeing Alert Requirements Bulletin 747-
57A2370 RB, dated March 2, 2022, uses the phrase ``the original 
issue date of Requirements Bulletin 747-57A2370 RB,'' this AD 
requires using ``the effective date of this AD.''

[[Page 73458]]

    (2) Where Boeing Alert Requirements Bulletin 747-57A2370 RB, 
dated March 2, 2022, specifies contacting Boeing for repair 
instructions: This AD requires doing the repair before further 
flight using a method approved in accordance with the procedures 
specified in paragraph (i) of this AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or responsible Flight Standards Office, 
as appropriate. If sending information directly to the manager of 
the certification office, send it to the attention of the person 
identified in paragraph (j) of this AD. Information may be emailed 
to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the responsible Flight Standards Office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Seattle 
ACO Branch, FAA, to make those findings. To be approved, the repair 
method, modification deviation, or alteration deviation must meet 
the certification basis of the airplane, and the approval must 
specifically refer to this AD.

(j) Related Information

    For more information about this AD, contact Nicole Tsang, 
Aerospace Engineer, Cabin Safety and Environmental Systems, FAA, 
Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; 
phone and fax: 206-231-3959; email: [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Boeing Alert Requirements Bulletin 747-57A2370 RB, dated 
March 2, 2022.
    (ii) [Reserved]
    (3) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet myboeingfleet.com.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, [email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on November 3, 2022.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2022-26082 Filed 11-29-22; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.