Airworthiness Directives; Bombardier, Inc., Airplanes, 63938-63940 [2022-22329]

Agencies

• Federal Aviation Administration
• DEPARTMENT OF TRANSPORTATION

[Federal Register Volume 87, Number 203 (Friday, October 21, 2022)]
[Rules and Regulations]
[Pages 63938-63940]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-22329]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-0886; Project Identifier MCAI-2022-00261-T; 
Amendment 39-22193; AD 2022-20-09]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Bombardier, Inc., Model BD-700-2A12 airplanes. This AD was 
prompted by reports of insufficient clearance between the surrounding 
structure/skin of the aircraft and select bleed air ducts that supply 
the wing ice protection system (WIPS) in the rear fuselage. This AD 
requires inspecting the bleed air duct and surrounding structure for 
minimum clearance and damage, and applicable corrective actions. The 
FAA is issuing this AD to address the unsafe condition on these 
products.

DATES: This AD is effective November 25, 2022.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of November 25, 
2022.

ADDRESSES: 
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2022-0886; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.
    Material Incorporated by Reference:
     For service information identified in this final rule, 
contact Bombardier Business Aircraft Customer Response Center, 400 
C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, Canada; 
telephone 514-855-2999; email bombardier.com">[email protected]bombardier.com; website 
bombardier.com.
     You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des

[[Page 63939]]

Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available at regulations.gov under 
Docket No. FAA-2022-0886.

FOR FURTHER INFORMATION CONTACT: Elizabeth Dowling, Aerospace Engineer, 
Mechanical Systems and Administrative Services Section, FAA, New York 
ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone 516-228-7300; email [email protected].

SUPPLEMENTARY INFORMATION:

Background

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to certain Bombardier, 
Inc., Model BD-700-2A12 airplanes. The NPRM published in the Federal 
Register on July 21, 2022 (87 FR 43462). The NPRM was prompted by AD 
CF-2022-05, dated February 24, 2022, issued by Transport Canada Civil 
Aviation (TCCA), which is the aviation authority for Canada (referred 
to after this as the MCAI). The MCAI states that insufficient clearance 
exists between the surrounding structure/skin of the aircraft and 
select bleed air ducts that supply the WIPS in the rear fuselage on the 
aircraft. Without sufficient clearance, the high pressure (HP) shroud 
could interfere with the surrounding structures and possibly compromise 
the HP ducting shroud's capability to provide bleed air leak routing, 
which could result in a bleed air leak being undetected. A significant 
undetected bleed air leak could expose the surrounding structure to 
heat stress, resulting in reduced structural integrity of the airplane.
    In the NPRM, the FAA proposed to require inspecting the bleed air 
duct and surrounding structure for minimum clearance and damage, and 
applicable corrective actions. The FAA is issuing this AD to address 
the unsafe condition on these products.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2022-0886.

Discussion of Final Airworthiness Directive

Comments

    The FAA received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA reviewed the relevant data and determined 
that air safety requires adopting this AD as proposed. Accordingly, the 
FAA is issuing this AD to address the unsafe condition on this product. 
Except for minor editorial changes, this AD is adopted as proposed in 
the NPRM. None of the changes will increase the economic burden on any 
operator.

Related Service Information Under 1 CFR Part 51

    Bombardier has issued Service Bulletin 700-36-7502, dated October 
28, 2020. This service information describes procedures for inspecting 
the bleed air duct and surrounding structure for minimum clearance and 
damage (wear and chafing), and corrective actions. Corrective actions 
include adjusting the ductwork if clearance is below the minimum 
required, and repairing any damage. This service information is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 8 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
1 work-hours x $85 per hour = $85............................              $1              $86             $688
----------------------------------------------------------------------------------------------------------------


                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
Up to 22 work-hours x $85 per hour =                $0           $1,870
 $1,870...............................
------------------------------------------------------------------------

    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this AD may be covered under warranty, thereby reducing the cost impact 
on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and

[[Page 63940]]

    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2022-20-09 Bombardier, Inc.: Amendment 39-22193; Docket No. FAA-
2022-0886; Project Identifier MCAI-2022-00261-T.

(a) Effective Date

    This airworthiness directive (AD) is effective November 25, 
2022.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc., Model BD-700-2A12 
airplanes, certificated in any category, serial numbers 70006, 
70007, 70009 through 70019 inclusive, 70021 through 70029 inclusive, 
and 70031.

(d) Subject

    Air Transport Association (ATA) of America Code 36, Pneumatic.

(e) Unsafe Condition

    This AD was prompted by reports of insufficient clearance 
between the surrounding structure/skin of the aircraft and select 
bleed air ducts that supply the wing ice protection system (WIPS) in 
the rear fuselage. The FAA is issuing this AD to address possible 
interference between the high pressure (HP) shroud and the 
surrounding structures, which could compromise the HP ducting 
shroud's capability to provide bleed air leak routing and result in 
a bleed air leak being undetected. A significant undetected bleed 
air leak could expose the surrounding structure to heat stress, 
resulting in reduced structural integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Within 21 months after the effective date of this AD: Inspect 
the affected bleed air ducts and surrounding structure for minimum 
clearance and damage (wear or chafing), and do all applicable 
corrective actions in accordance with the Accomplishment 
Instructions of Bombardier Service Bulletin 700-36-7502, dated 
October 28, 2020. Do all applicable corrective actions before 
further flight.

(h) No Reporting Requirement

    Although Bombardier Service Bulletin 700-36-7502, dated October 
28, 2020, specifies to submit certain information to the 
manufacturer, this AD does not include that requirement.

(i) Other AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or responsible Flight Standards Office, as appropriate. If 
sending information directly to the manager of the certification 
office, send it to ATTN: Program Manager, Continuing Operational 
Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7300. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the responsible Flight 
Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

(j) Additional Information

    (1) Refer to TCCA AD CF-2022-05, dated February 24, 2022, for 
related information. This TCCA AD may be found in the AD docket at 
regulations.gov under Docket No. FAA-2022-0886.
    (2) For more information about this AD, contact Elizabeth 
Dowling, Aerospace Engineer, Mechanical Systems and Administrative 
Services Section, FAA, New York ACO Branch, 1600 Stewart Avenue, 
Suite 410, Westbury, NY 11590; telephone 516-228-7300; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Service Bulletin 700-36-7502, dated October 28, 
2020.
    (ii) [Reserved]
    (3) For service information identified in this AD, contact 
Bombardier Business Aircraft Customer Response Center, 400 
C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, Canada; 
telephone 514-855-2999; email bombardier.com">[email protected]bombardier.com; website 
bombardier.com.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email [email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on September 19, 2022.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2022-22329 Filed 10-20-22; 8:45 am]
BILLING CODE 4910-13-P