Airworthiness Directives; Airbus SAS Airplanes, 47555-47557 [2021-18332]

Agencies

• Federal Aviation Administration
• DEPARTMENT OF TRANSPORTATION

[Federal Register Volume 86, Number 163 (Thursday, August 26, 2021)]
[Rules and Regulations]
[Pages 47555-47557]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-18332]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0142; Project Identifier MCAI-2020-01400-T; 
Amendment 39-21665; AD 2021-16-03]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Airbus SAS Model A350-941 and -1041 airplanes. This AD was 
prompted by a report of in-production findings of missing or incorrect 
application of the lightning strike edge glow sealant protection at 
specific locations in the wing tanks. This AD requires an inspection 
for missing or incorrect application of the lightning strike edge glow 
sealant protection at certain locations in the wing tanks, and 
corrective action, as specified in a European Union Aviation Safety 
Agency (EASA) AD, which is incorporated by reference. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD is effective September 30, 2021.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of September 
30, 2021.

ADDRESSES: For EASA material incorporated by reference (IBR) in this 
AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 8999 000; email [email protected]; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this IBR material at the 
FAA, Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability of 
this material at the FAA, call 206-231-3195. It is also available in 
the AD docket on the internet at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0142.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0142; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Nick Wilson, Aerospace Engineer, Large 
Aircraft Section, International Validation Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3230; email 
[email protected].

SUPPLEMENTARY INFORMATION:

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2020-0220, dated October 13, 2020 
(EASA AD 2020-0220) (also referred to after this as the Mandatory 
Continuing Airworthiness Information, or the MCAI), to correct an 
unsafe condition for certain Airbus SAS Model A350-941 and -1041 
airplanes.
    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR

[[Page 47556]]

part 39 by adding an AD that would apply to certain Airbus SAS Model 
A350-941 and -1041 airplanes. The NPRM published in the Federal 
Register on March 11, 2021 (86 FR 13833). The NPRM was prompted by a 
report of in-production findings of missing or incorrect application of 
the lightning strike edge glow sealant protection at specific locations 
in the wing tanks. The NPRM proposed to require an inspection for 
missing or incorrect application of the lightning strike edge glow 
sealant protection at certain locations in the wing tanks, and 
corrective action, as specified in EASA AD 2020-0220.
    The FAA is issuing this AD to address missing or incorrectly 
applied sealant, which in combination with an undetected incorrect 
installation of an adjacent fastener and a lightning strike in the 
immediate area, could result in ignition of the fuel air mixture inside 
the affected fuel tanks and loss of the airplane. See the MCAI for 
additional background information.

Comments

    The FAA gave the public the opportunity to participate in 
developing this final rule. The FAA has considered the comment 
received. Air Line Pilots Association, International (ALPA) stated that 
it supports the NPRM.

Conclusion

    The FAA reviewed the relevant data, considered the comment 
received, and determined that air safety and the public interest 
require adopting this final rule as proposed, except for minor 
editorial changes. The FAA has determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for addressing the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

    EASA AD 2020-0220 specifies procedures for an inspection for 
missing or incorrect application of the lightning strike edge glow 
sealant protection at certain locations in the wing tanks 
(discrepancies), and corrective action. Corrective actions include 
applying sealant in areas where sealant was found to be missing or 
incorrectly applied. This material is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 16 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
               Labor cost                   Parts cost         Cost per product         Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Up to 67 work-hours x $85 per hour = Up               $0  Up to $5,695..............  Up to $91,120.
 to $5,695.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition action that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need this on-condition action:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
1 work-hours x $85 per hour = $85.....              $0              $85
------------------------------------------------------------------------

    According to the manufacturer, some or all of the costs of this AD 
may be covered under warranty, thereby reducing the cost impact on 
affected operators. The FAA does not control warranty coverage for 
affected operators. As a result, the FAA has included all known costs 
in the cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.

[[Page 47557]]

Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2021-16-03 Airbus SAS: Amendment 39-21665; Docket No. FAA-2021-0142; 
Project Identifier MCAI-2020-01400-T.

(a) Effective Date

    This airworthiness directive (AD) is effective September 30, 
2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A350-941 and -1041 
airplanes, certificated in any category, as identified in European 
Union Aviation Safety Agency (EASA) AD 2020-0220, dated October 13, 
2020 (EASA AD 2020-0220).

(d) Subject

    Air Transport Association (ATA) of America Code 57, Wings.

(e) Reason

    This AD was prompted by in-production findings of missing or 
incorrect application of the lightning strike edge glow sealant 
protection at specific locations in the wing tanks. The FAA is 
issuing this AD to address missing or incorrectly applied sealant, 
which in combination with an undetected incorrect installation of an 
adjacent fastener and a lightning strike in the immediate area, 
could result in ignition of the fuel-air mixture inside the affected 
fuel tanks and loss of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2020-0220.

(h) Exceptions to EASA AD 2020-0220

    (1) Where EASA AD 2020-0220 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2020-0220 does not apply 
to this AD.
    (3) Where paragraph (1) of EASA AD 2020-0220 gives a compliance 
time of ``the next scheduled maintenance tank entry, or before 
exceeding 6 years since Airbus date of manufacture, whichever occurs 
first after the effective date of this AD,'' for this AD, the 
compliance time is the later of the times specified in paragraphs 
(h)(3)(i) and (ii) of this AD.
    (i) The next scheduled maintenance tank entry, or before 
exceeding 6 years since Airbus date of manufacture, whichever occurs 
first after the effective date of this AD.
    (ii) Within 6 months after the effective date of this AD.
    (4) Where paragraph (2) of EASA AD 2020-0220 refers to 
``discrepancies,'' for this AD, discrepancies include missing or 
incorrectly applied sealant.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (j) of this 
AD. Information may be emailed to: [email protected]. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Airbus 
SAS's EASA Design Organization Approval (DOA). If approved by the 
DOA, the approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information contains 
procedures or tests that are identified as RC, those procedures and 
tests must be done to comply with this AD; any procedures or tests 
that are not identified as RC are recommended. Those procedures and 
tests that are not identified as RC may be deviated from using 
accepted methods in accordance with the operator's maintenance or 
inspection program without obtaining approval of an AMOC, provided 
the procedures and tests identified as RC can be done and the 
airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures or tests identified as RC 
require approval of an AMOC.

(j) Related Information

    For more information about this AD, contact Nick Wilson, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3230; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2020-0220, 
dated October 13, 2020.
    (ii) [Reserved]
    (3) For EASA AD 2020-0220, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; internet www.easa.europa.eu. You may find this 
EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195. This material may be found in the AD 
docket on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2021-0142.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on July 21, 2021.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2021-18332 Filed 8-25-21; 8:45 am]
BILLING CODE 4910-13-P