Airworthiness Directives; Saab AB, Support and Services (Formerly Known as Saab AB, Saab Aeronautics) Airplanes, 81383-81385 [2020-27620]

Agencies

• Federal Aviation Administration
• DEPARTMENT OF TRANSPORTATION

[Federal Register Volume 85, Number 242 (Wednesday, December 16, 2020)]
[Rules and Regulations]
[Pages 81383-81385]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-27620]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-0840; Project Identifier MCAI-2020-00907-T; 
Amendment 39-21344; AD 2020-25-02]
RIN 2120-AA64


Airworthiness Directives; Saab AB, Support and Services (Formerly 
Known as Saab AB, Saab Aeronautics) Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Saab AB, Support and Services Model 340A (SAAB/SF340A) and SAAB 340B 
airplanes; and Model SAAB 2000 airplanes. This AD was prompted by 
reports that certain nose landing gear (NLG) door attachment bolts are 
susceptible to hydrogen embrittlement. This AD requires replacing 
certain NLG door attachment bolts with serviceable bolts, as specified 
in a European Union Aviation Safety Agency (EASA) AD, which is 
incorporated by reference. The FAA is issuing this AD to address the 
unsafe condition on these products.

DATES: This AD is effective January 21, 2021.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of January 21, 
2021.

ADDRESSES: For material incorporated by reference (IBR) in this AD, 
contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 8999 000; email [email protected]; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this IBR material at the 
FAA, Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability of 
this material at the FAA, call 206-231-3195. It is also available in 
the AD docket on the internet at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2020-0840.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-

[[Page 81384]]

0840; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Shahram Daneshmandi, Aerospace 
Engineer, Large Aircraft Section, International Validation Branch, FAA, 
2200 South 216th St., Des Moines, WA 98198; telephone and fax 206 231 
3220; email Shahram. [email protected].

SUPPLEMENTARY INFORMATION:

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2020-0149, dated July 7, 2020 (EASA 
AD 2020-0149) (also referred to as the Mandatory Continuing 
Airworthiness Information, or the MCAI), to correct an unsafe condition 
for all Saab AB, Support and Services Model 340A (SAAB/SF340A) and SAAB 
340B airplanes; and Model SAAB 2000 airplanes.
    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to all Saab AB, Support 
and Services Model 340A (SAAB/SF340A) and SAAB 340B airplanes; and 
Model SAAB 2000 airplanes. The NPRM published in the Federal Register 
on September 15, 2020 (85 FR 57168). The NPRM was prompted by reports 
that certain NLG door attachment bolts are susceptible to hydrogen 
embrittlement. The NPRM proposed to require replacing certain NLG door 
attachment bolts with serviceable bolts, as specified in an EASA AD.
    The FAA is issuing this AD to address NLG door attachment bolts 
that were incorrectly manufactured and are susceptible to hydrogen 
embrittlement, decreasing the mechanical characteristics. This 
condition could lead to failure of the affected parts, which would 
impair the link between the NLG and NLG door and could prevent the 
extension or retraction of the NLG, and cause consequent damage to the 
airplane and possible loss of control during landing. See the MCAI for 
additional background information.

Comments

    The FAA gave the public the opportunity to participate in 
developing this final rule. The FAA received no comments on the NPRM or 
on the determination of the cost to the public.

Conclusion

    The FAA reviewed the relevant data and determined that air safety 
and the public interest require adopting this final rule as proposed, 
except for minor editorial changes. The FAA has determined that these 
minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for addressing the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

    EASA AD 2020-0149 describes procedures for identifying and 
replacing certain NLG door attachment bolts with serviceable bolts. 
This material is reasonably available because the interested parties 
have access to it through their normal course of business or by the 
means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 103 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                     Estimated Costs for Required Actions *
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
2 work-hours x $85 per hour = $170...........................             * $           * $170        * $17,510
----------------------------------------------------------------------------------------------------------------
* The FAA has received no definitive data that would enable the FAA to provide parts cost estimates for the bolt
  replacement specified in this AD.

    According to the manufacturer, some or all of the costs of this AD 
may be covered under warranty, thereby reducing the cost impact on 
affected individuals. The FAA does not control warranty coverage for 
affected individuals. As a result, the FAA has included all known costs 
in the cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

[[Page 81385]]

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2020-25-02 Saab AB, Support and Services (Formerly Known as Saab AB, 
Saab Aeronautics): Amendment 39-21344; Docket No. FAA-2020-0840; 
Project Identifier MCAI-2020-00907-T.

(a) Effective Date

    This airworthiness directive (AD) is effective January 21, 2021.

(b) Affected Airworthiness Directives (ADs)

    None.

(c) Applicability

    This AD applies to all Saab AB, Support and Services (Formerly 
Known as Saab AB, Saab Aeronautics) Model 340A (SAAB/SF340A) and 
SAAB 340B airplanes; and Model SAAB 2000 airplanes, certificated in 
any category.

(d) Subject

    Air Transport Association (ATA) of America Code 32, Landing 
Gear.

(e) Reason

    This AD was prompted by reports that certain nose landing gear 
(NLG) door attachment bolts are susceptible to hydrogen 
embrittlement. The FAA is issuing this AD to address NLG door 
attachment bolts that were incorrectly manufactured and are 
susceptible to hydrogen embrittlement, decreasing the mechanical 
characteristics. This condition could lead to failure of the 
affected parts, which would impair the link between the NLG and NLG 
door and could prevent the extension or retraction of the NLG, and 
cause consequent damage to the airplane and possible loss of control 
during landing.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2020-0149, dated July 7, 2020 (EASA AD 2020-0149).

(h) Exceptions to EASA AD 2020-0149

    (1) Where EASA AD 2020-0149 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2020-0149 does not apply 
to this AD.

 (i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (j) of this 
AD. Information may be emailed to: [email protected]. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Saab AB, 
Support and Services' EASA Design Organization Approval (DOA). If 
approved by the DOA, the approval must include the DOA-authorized 
signature.

(j) Related Information

    For more information about this AD, contact Shahram Daneshmandi, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3220; email Shahram.[email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2020-0149, 
dated July 7, 2020.
    (ii) [Reserved].
    (3) For EASA AD 2020-0149, contact the EASA, Konrad-Adenauer-
Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; internet www.easa.europa.eu. You may find this 
EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195. This material may be found in the AD 
docket on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2020-0840.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on November 23, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2020-27620 Filed 12-15-20; 8:45 am]
BILLING CODE 4910-13-P