Rescheduled Public Hearing, 78126 [2020-26608]

Download as PDF 78126 Federal Register / Vol. 85, No. 233 / Thursday, December 3, 2020 / Notices 8′ x 12′8″ 8′ x 15′ 8′ x 20′ Any product imported, sold, or invoiced in one of these size combinations is within the scope. ASTM specification A1064/A1064M provides for permissible variations in wire gauges, the spacing between transverse and longitudinal wires, and the length and width combinations. To the extent a roll or sheet of welded wire mesh falls within these permissible variations, it is within this scope. ASTM specification A1064/A1064M also defines permissible oversteeling, which is the use of a heavier gauge wire with a larger cross-sectional area than nominally specified. Maximum oversteeling No. W/D No. 1.4 2.1 2.9 4.0 (i.e., (i.e., (i.e., (i.e., 10 gauge) ..................................................................... 8 gauge) ....................................................................... 6 gauge) ....................................................................... 4 gauge) ....................................................................... khammond on DSKJM1Z7X2PROD with NOTICES To the extent a roll or sheet of welded wire mesh falls within the permissible variations provided above, it is within this scope. In addition to the tolerances permitted in ASTM specification A1064/A1064M, wire mesh within this scope includes combinations where: 1. A width and/or length combination varies by ± one grid size in any direction, i.e., ± 6 inches in length or width where the wire mesh’s grid size is ‘‘6 x 6’’; and/or 2. The center-to-center spacing between individual wires may vary by up to one quarter of an inch from the nominal grid size specified. Length is measured from the ends of any wire and width is measured between the center-line of end longitudinal wires. Additionally, although the subject wire mesh typically meets ASTM A1064/A1064M, the failure to include certifications, test reports or other documentation establishing that the product meets this specification does not remove the product from the scope. Wire mesh made to comparable foreign specifications (e.g., DIN, JIS, etc.) or proprietary specifications is included in the scope. Excluded from the scope is wire mesh that is galvanized (i.e., coated with zinc) or coated with an epoxy coating. In order to be excluded as galvanized, the excluded welded wire mesh must have a zinc coating thickness meeting the requirements of ASTM specification A641/A641M. Epoxy coating is a mix of epoxy resin and hardener that can be applied to the surface of steel wire. Merchandise subject to this investigation are classified under Harmonized Tariff Schedule of the United States (HTSUS) categories 7314.20.0000 and 7314.39.0000. While HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of this investigation is dispositive. Appendix II List of Topics Discussed in the Preliminary Decision Memorandum I. Summary II. Background III. Scope of the Investigation IV. Scope Comments V. Injury Test VI. Use of Facts Otherwise Available and VerDate Sep<11>2014 19:48 Dec 02, 2020 Jkt 253001 It also permits a wire diameter tolerance of ± 0.003 inches for products up to W5/D5 and ± 0.004 for sizes over W5/D5. A producer may oversteel by increasing smooth or deformed wire diameter up to two whole number size increments on Table 1 of A1064. Subject wire mesh has the following actual wire diameter ranges, which account for both oversteeling and diameter tolerance: 3.4 4.1 4.9 6.0 Diameter range (inch) 0.093 0.161 0.189 0.223 to to to to 0.211. 0.231. 0.253. 0.280. Adverse Inferences VII. Subsidies Valuation VIII. Analysis of Programs IX. Recommendation [FR Doc. 2020–26628 Filed 12–2–20; 8:45 am] BILLING CODE 3510–DS–P U.S. INTERNATIONAL DEVELOPMENT FINANCE CORPORATION Rescheduled Public Hearing U.S. International Development Finance Corporation. ACTION: Announcement of new date/ time for public hearing, previously scheduled for December 9, 2020, 2p.m. AGENCY: The Board of Directors of the U.S. International Development Finance Corporation (‘‘DFC’’) will hold a public hearing on December 10, 2020. This hearing will afford an opportunity for any person to present views in accordance with the BUILD Act of 2018. Those wishing to present at the hearing must provide advance notice to the agency as detailed below. Please note that this hearing was originally scheduled for Wednesday, December 9, 2020; notice of which was published in the Federal Register on Thursday, November 5, 2020. DATES: Public hearing: 2:00 p.m., Thursday, December 10, 2020. Deadline for notifying agency of an intent to attend or present at the public hearing: 5:00 p.m., Thursday, December 3, 2020. Deadline for submitting a written statement: 5:00 p.m., Thursday, December 3, 2020. ADDRESSES: Public hearing: Virtual; Access information provided at the time of attendance registration. You may send notices of intent to attend, present, or submit a written statement to Catherine F. I. Andrade, DFC Corporate Secretary, via email at candrade@dfc.gov. SUMMARY: PO 00000 Frm 00014 Fmt 4703 Sfmt 9990 Instructions: A notice of intent to attend the public hearing or to present at the public hearing must include the individual’s name, title, organization, address, email, telephone number, and a concise summary of the subject matter to be presented. Oral presentations may not exceed five (5) minutes. The time for individual presentations may be reduced proportionately, if necessary, to afford all participants who have submitted a timely request an opportunity to be heard. Submission of written statements must include the individual’s name, title, organization, address, email, and telephone number. The statement must be typewritten, double-spaced, and may not exceed ten (10) pages. FOR FURTHER INFORMATION CONTACT: Catherine F.I. Andrade, DFC Corporate Secretary, (202) 336–8768, or candrade@dfc.gov. The public hearing will take place via videoand teleconference. Upon registering, participants and observers will be provided instructions on accessing the hearing. DFC will prepare an agenda for the hearing identifying speakers, setting forth the subject on which each participant will speak, and the time allotted for each presentation. The agenda will be available at the time of the hearing. SUPPLEMENTARY INFORMATION: Authority: 22 U.S.C. 9613(c). Catherine F.I. Andrade, DFC Corporate Secretary. [FR Doc. 2020–26608 Filed 12–2–20; 8:45 am] BILLING CODE 3210–02–P E:\FR\FM\03DEN1.SGM 03DEN1

Agencies

  • U.S. INTERNATIONAL DEVELOPMENT FINANCE CORPORATION
[Federal Register Volume 85, Number 233 (Thursday, December 3, 2020)]
[Notices]
[Page 78126]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-26608]


=======================================================================
-----------------------------------------------------------------------

U.S. INTERNATIONAL DEVELOPMENT FINANCE CORPORATION


Rescheduled Public Hearing

AGENCY: U.S. International Development Finance Corporation.

ACTION: Announcement of new date/time for public hearing, previously 
scheduled for December 9, 2020, 2p.m.

-----------------------------------------------------------------------

SUMMARY: The Board of Directors of the U.S. International Development 
Finance Corporation (``DFC'') will hold a public hearing on December 
10, 2020. This hearing will afford an opportunity for any person to 
present views in accordance with the BUILD Act of 2018. Those wishing 
to present at the hearing must provide advance notice to the agency as 
detailed below. Please note that this hearing was originally scheduled 
for Wednesday, December 9, 2020; notice of which was published in the 
Federal Register on Thursday, November 5, 2020.

DATES: Public hearing: 2:00 p.m., Thursday, December 10, 2020.
    Deadline for notifying agency of an intent to attend or present at 
the public hearing: 5:00 p.m., Thursday, December 3, 2020.
    Deadline for submitting a written statement: 5:00 p.m., Thursday, 
December 3, 2020.

ADDRESSES: Public hearing: Virtual; Access information provided at the 
time of attendance registration.
    You may send notices of intent to attend, present, or submit a 
written statement to Catherine F. I. Andrade, DFC Corporate Secretary, 
via email at [email protected].
    Instructions: A notice of intent to attend the public hearing or to 
present at the public hearing must include the individual's name, 
title, organization, address, email, telephone number, and a concise 
summary of the subject matter to be presented. Oral presentations may 
not exceed five (5) minutes. The time for individual presentations may 
be reduced proportionately, if necessary, to afford all participants 
who have submitted a timely request an opportunity to be heard. 
Submission of written statements must include the individual's name, 
title, organization, address, email, and telephone number. The 
statement must be typewritten, double-spaced, and may not exceed ten 
(10) pages.

FOR FURTHER INFORMATION CONTACT: Catherine F.I. Andrade, DFC Corporate 
Secretary, (202) 336-8768, or [email protected].

SUPPLEMENTARY INFORMATION: The public hearing will take place via 
video- and teleconference. Upon registering, participants and observers 
will be provided instructions on accessing the hearing. DFC will 
prepare an agenda for the hearing identifying speakers, setting forth 
the subject on which each participant will speak, and the time allotted 
for each presentation. The agenda will be available at the time of the 
hearing.

    Authority: 22 U.S.C. 9613(c).

Catherine F.I. Andrade,
DFC Corporate Secretary.
[FR Doc. 2020-26608 Filed 12-2-20; 8:45 am]
BILLING CODE 3210-02-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.