Airworthiness Directives; Airbus SAS Airplanes, 64985-64987 [2019-25605]

Download as PDF Federal Register / Vol. 84, No. 228 / Tuesday, November 26, 2019 / Rules and Regulations 12 CFR part 325 to occupy all of part 325.3 The final rule inadvertently omitted corresponding changes from ‘‘subpart’’ to ‘‘part’’ in three sections of the final rule: §§ 325.1(c)(7), 325.3(a)(1), and 325.7(b). Accordingly, this document is issued to correct those sections of the final rule with the appropriate references to ‘‘part’’ 325. For the reasons set out in the preamble, the FDIC hereby amend 12 CFR part 325 by making the following correcting amendments. PART 325—STRESS TESTING 1. The authority citation for part 325 continues to read as follows: ■ Authority: 12 U.S.C. 5365(i)(2), 12 U.S.C. 5412(b)(2)(C), 12 U.S.C. 1818, 12 U.S.C. 1819(a)(Tenth), 12 U.S.C. 1831o, and 12 U.S.C. 1831p–1. publishes a summary of its stress test results with its parent bank holding company’s or savings and loan holding company’s summary of stress test results. Subsidiary covered banks electing to satisfy their public disclosure requirement in this manner must include a summary of changes in regulatory capital ratios of such covered bank over the planning horizon, and an explanation of the most significant causes for the changes in regulatory capital ratios. * * * * * www.easa.europa.eu. You may find this IBR material on the EASA website at https://ad.easa.europa.eu. You may view this IBR material at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. It is also available in the AD docket on the internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2019– 0667. Dated on November 18, 2019. Federal Deposit Insurance Corporation. Annmarie H. Boyd, Assistant Executive Secretary. You may examine the AD docket on the internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2019– 0667; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, the regulatory evaluation, any comments received, and other information. The address for Docket Operations is U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE, Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Sanjay Ralhan, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206–231–3223. SUPPLEMENTARY INFORMATION: [FR Doc. 2019–25691 Filed 11–22–19; 8:45 am] BILLING CODE 6714–01–P 2. Amend § 325.1 by revising paragraph (c)(7) to read as follows: DEPARTMENT OF TRANSPORTATION § 325.1 Authority, purpose, and reservation of authority. Federal Aviation Administration ■ * * * * * (c) * * * (7) Nothing in this part limits the authority of the Corporation under any other provision of law or regulation to take supervisory or enforcement action, including action to address unsafe and unsounds practices or conditions, or violations of law or regulation. * * * * * ■ 3. Amend § 325.3 by revising paragraph (a)(1) to read as follows: § 325.3 Applicability (a) * * * (1) A state nonmember bank or state savings association that is a covered bank as of December 31, 2019, is subject to the requirements of this part for the 2020 reporting year. * * * * * ■ 4. Amend § 325.7 by revising paragraph (b) to read as follows: § 325.7 Publication of stress test results. * * * * * (b) Publication method. The summary required under this section may be published on the covered ban’s website or in any other forum that is reasonably accessible to the public. A covered bank that is a consolidated subsidiary of a bank holding company or savings and loan holding company that is required to conduct a company-run stress test under applicable regulations of the Board of Governors of the Federal Reserve System will be deemed to have satisfied the public disclosure requirements under this part if it 3 83 FR 17737 (April 24, 2019). VerDate Sep<11>2014 15:52 Nov 25, 2019 Jkt 250001 64985 14 CFR Part 39 [Docket No. FAA–2019–0667; Product Identifier 2019–NM–085–AD; Amendment 39–19791; AD 2019–22–12] RIN 2120–AA64 Airworthiness Directives; Airbus SAS Airplanes Examining the AD Docket Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. Discussion The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A320–214, –216, –232, and –233 airplanes. This AD was prompted by a report of undetected contacts between certain harnesses of the common fuel quantity indicating system and the center tank structure. This AD requires modification of the fasteners for certain harness routings, as specified in a European Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products. DATES: This AD is effective December 31, 2019. The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of December 31, 2019. ADDRESSES: For the material incorporated by reference (IBR) in this AD, contact the EASA, KonradAdenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 221 89990 1000; email: ADs@easa.europa.eu; internet: The EASA, which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2018–0155, dated July 20, 2018 (‘‘EASA AD 2018–0155’’) (also referred to as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition for certain Airbus SAS Model A320–214, –216, –232, and –233 airplanes. The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to certain Airbus SAS Model A320–214, –216, –232, and –233 airplanes. The NPRM published in the Federal Register on August 30, 2019 (84 FR 45690). The NPRM was prompted by a report of undetected contacts between certain harnesses of the common fuel quantity indicating system and the center tank structure. The NPRM proposed to require modification of the fasteners for certain harness routings. The FAA is issuing this AD to address undetected contacts between certain harnesses of the common fuel quantity indicating system and the center tank AGENCY: SUMMARY: PO 00000 Frm 00019 Fmt 4700 Sfmt 4700 E:\FR\FM\26NOR1.SGM 26NOR1 64986 Federal Register / Vol. 84, No. 228 / Tuesday, November 26, 2019 / Rules and Regulations structure, which could create, in case of a lightning strike with chafing present, an ignition source inside the center fuel tank, possibly resulting in a fuel tank explosion and consequent loss of the airplane. See the MCAI for additional background information. Comments The FAA gave the public the opportunity to participate in developing this final rule. The FAA has considered the comment received. United Airlines had no objections to the NPRM. Conclusion The FAA reviewed the relevant data, considered the comment received, and determined that air safety and the public interest require adopting this final rule as proposed, except for minor editorial changes. The FAA has determined that these minor changes: • Are consistent with the intent that was proposed in the NPRM for addressing the unsafe condition; and • Do not add any additional burden upon the public than was already proposed in the NPRM. Related IBR Material Under 1 CFR Part 51 EASA AD 2018–0155 describes procedures for modification of the fasteners for harness routings 17QT and 18QT. This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section. Costs of Compliance The FAA estimates that this AD affects 5 airplanes of U.S. registry. The FAA estimates the following costs to comply with this AD: ESTIMATED COSTS FOR REQUIRED ACTIONS Labor cost Parts cost Cost per product Cost on U.S. operators 5 work-hours × $85 per hour = $425 .......................................................................................... $200 $625 $3,125 Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. This AD is issued in accordance with authority delegated by the Executive Director, Aircraft Certification Service, as authorized by FAA Order 8000.51C. In accordance with that order, issuance of ADs is normally a function of the Compliance and Airworthiness Division, but during this transition period, the Executive Director has delegated the authority to issue ADs applicable to transport category airplanes and associated appliances to the Director of the System Oversight Division. Regulatory Findings 15:52 Nov 25, 2019 List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ This AD will not have federalism implications under Executive Order VerDate Sep<11>2014 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Will not affect intrastate aviation in Alaska, and (3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. Jkt 250001 PO 00000 Frm 00020 Fmt 4700 Sfmt 4700 2019–22–12 Airbus SAS: Amendment 39– 19791; Docket No. FAA–2019–0667; Product Identifier 2019–NM–085–AD. (a) Effective Date This AD is effective December 31, 2019. (b) Affected ADs None. (c) Applicability This AD applies to Airbus SAS Model A320–214, –216, –232, and –233 airplanes, certificated in any category, as identified in European Aviation Safety Agency (EASA) AD 2018–0155, dated July 20, 2018 (‘‘EASA AD 2018–0155’’). (d) Subject Air Transport Association (ATA) of America Code 92, Electrical system installation. (e) Reason This AD was prompted by a report of undetected contacts between certain harnesses of the common fuel quantity indicating system and the center tank structure. The FAA is issuing this AD to address undetected contacts between certain harnesses of the common fuel quantity indicating system and the center tank structure, which could create, in case of a lightning strike with chafing present, an ignition source inside the center fuel tank, possibly resulting in a fuel tank explosion and consequent loss of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2018–0155. E:\FR\FM\26NOR1.SGM 26NOR1 Federal Register / Vol. 84, No. 228 / Tuesday, November 26, 2019 / Rules and Regulations (h) Exceptions to EASA AD 2018–0155 (1) Where EASA AD 2018–0155 refers to its effective date, this AD requires using the effective date of this AD. (2) The ‘‘Remarks’’ section of EASA AD 2018–0155 does not apply to this AD. (i) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@ faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS’s EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOAauthorized signature. (3) Required for Compliance (RC): For any service information referenced in EASA AD 2018–0155 that contains RC procedures and tests: Except as required by paragraph (i)(2) of this AD, RC procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator’s maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (j) Related Information For more information about this AD, contact Sanjay Ralhan, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206–231– 3223. (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Aviation Safety Agency (EASA) AD 2018–0155, dated July 20, 2018. VerDate Sep<11>2014 15:52 Nov 25, 2019 Jkt 250001 (ii) [Reserved] (3) For information about EASA AD 2018– 0155, contact the EASA, Konrad-AdenauerUfer 3, 50668 Cologne, Germany; phone: +49 221 89990 6017; email: ADs@easa.europa.eu; Internet: www.easa.europa.eu. You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. (4) You may view this material at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. This material may be found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2019–0667. (5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email: fedreg.legal@nara.gov, or go to: https:// www.archives.gov/federal-register/cfr/ibrlocations.html. Issued in Des Moines, Washington, on November 6, 2019. Michael Kaszycki, Acting Director, System Oversight Division, Aircraft Certification Service. [FR Doc. 2019–25605 Filed 11–25–19; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2019–0611; Product Identifier 2019–NM–095–AD; Amendment 39–19793; AD 2019–22–14] RIN 2120–AA64 Airworthiness Directives; Airbus SAS Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. AGENCY: The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350–941 airplanes. This AD was prompted by the results of a structural analysis, which identified that the upper frame fittings (UFFs) of the forward cargo door surrounding structure have a low fatigue life. This AD requires repetitive inspections of the forward cargo door UFFs and brackets for discrepancies and, depending on the findings, doing applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products. DATES: This AD is effective December 31, 2019. SUMMARY: PO 00000 Frm 00021 Fmt 4700 Sfmt 4700 64987 The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of December 31, 2019. ADDRESSES: For the material incorporated by reference (IBR) in this AD, contact the EASA, KonradAdenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 89990 1000; email ADs@easa.europa.eu; internet www.easa.europa.eu. You may find this IBR material on the EASA website at https://ad.easa.europa.eu. You may view this IBR material at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. It is also available in the AD docket on the internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2019– 0611. Examining the AD Docket You may examine the AD docket on the internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2019– 0611; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, the regulatory evaluation, any comments received, and other information. The address for Docket Operations is U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE, Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Kathleen Arrigotti, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206–231–3218. SUPPLEMENTARY INFORMATION: Discussion The EASA, which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2019–0126, dated June 5, 2019 (‘‘EASA AD 2019–0126’’) (also referred to as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition for certain Airbus SAS Model A350–941 airplanes. The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to certain Airbus SAS Model A350–941 airplanes. The NPRM published in the Federal Register on August 30, 2019 (84 FR 45694). The NPRM was prompted by the results of a structural analysis, which identified E:\FR\FM\26NOR1.SGM 26NOR1

Agencies

[Federal Register Volume 84, Number 228 (Tuesday, November 26, 2019)]
[Rules and Regulations]
[Pages 64985-64987]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-25605]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0667; Product Identifier 2019-NM-085-AD; Amendment 
39-19791; AD 2019-22-12]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Airbus SAS Model A320-214, -216, -232, and -233 airplanes. This 
AD was prompted by a report of undetected contacts between certain 
harnesses of the common fuel quantity indicating system and the center 
tank structure. This AD requires modification of the fasteners for 
certain harness routings, as specified in a European Aviation Safety 
Agency (EASA) AD, which is incorporated by reference. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD is effective December 31, 2019.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of December 31, 
2019.

ADDRESSES: For the material incorporated by reference (IBR) in this AD, 
contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
phone: +49 221 89990 1000; email: [email protected]; internet: 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this IBR material at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. 
For information on the availability of this material at the FAA, call 
206-231-3195. It is also available in the AD docket on the internet at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2019-0667.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0667; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, the regulatory evaluation, any comments received, and 
other information. The address for Docket Operations is U.S. Department 
of Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Sanjay Ralhan, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; phone and fax: 206-231-3223.

SUPPLEMENTARY INFORMATION:

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2018-0155, dated July 20, 2018 
(``EASA AD 2018-0155'') (also referred to as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for certain Airbus SAS Model A320-214, -216, -232, and -233 
airplanes.
    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to certain Airbus SAS 
Model A320-214, -216, -232, and -233 airplanes. The NPRM published in 
the Federal Register on August 30, 2019 (84 FR 45690). The NPRM was 
prompted by a report of undetected contacts between certain harnesses 
of the common fuel quantity indicating system and the center tank 
structure. The NPRM proposed to require modification of the fasteners 
for certain harness routings.
    The FAA is issuing this AD to address undetected contacts between 
certain harnesses of the common fuel quantity indicating system and the 
center tank

[[Page 64986]]

structure, which could create, in case of a lightning strike with 
chafing present, an ignition source inside the center fuel tank, 
possibly resulting in a fuel tank explosion and consequent loss of the 
airplane. See the MCAI for additional background information.

Comments

    The FAA gave the public the opportunity to participate in 
developing this final rule. The FAA has considered the comment 
received. United Airlines had no objections to the NPRM.

Conclusion

    The FAA reviewed the relevant data, considered the comment 
received, and determined that air safety and the public interest 
require adopting this final rule as proposed, except for minor 
editorial changes. The FAA has determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for addressing the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2018-0155 describes procedures for modification of the 
fasteners for harness routings 17QT and 18QT.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 5 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
5 work-hours x $85 per hour = $425...........................            $200             $625           $3,125
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to transport category airplanes and 
associated appliances to the Director of the System Oversight Division.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2019-22-12 Airbus SAS: Amendment 39-19791; Docket No. FAA-2019-0667; 
Product Identifier 2019-NM-085-AD.

(a) Effective Date

    This AD is effective December 31, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A320-214, -216, -232, and -
233 airplanes, certificated in any category, as identified in 
European Aviation Safety Agency (EASA) AD 2018-0155, dated July 20, 
2018 (``EASA AD 2018-0155'').

(d) Subject

    Air Transport Association (ATA) of America Code 92, Electrical 
system installation.

(e) Reason

    This AD was prompted by a report of undetected contacts between 
certain harnesses of the common fuel quantity indicating system and 
the center tank structure. The FAA is issuing this AD to address 
undetected contacts between certain harnesses of the common fuel 
quantity indicating system and the center tank structure, which 
could create, in case of a lightning strike with chafing present, an 
ignition source inside the center fuel tank, possibly resulting in a 
fuel tank explosion and consequent loss of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2018-0155.

[[Page 64987]]

(h) Exceptions to EASA AD 2018-0155

    (1) Where EASA AD 2018-0155 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2018-0155 does not apply 
to this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (j) of this AD. Information may 
be emailed to: [email protected]. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's 
EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): For any service information 
referenced in EASA AD 2018-0155 that contains RC procedures and 
tests: Except as required by paragraph (i)(2) of this AD, RC 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures and tests identified as 
RC can be done and the airplane can be put back in an airworthy 
condition. Any substitutions or changes to procedures or tests 
identified as RC require approval of an AMOC.

(j) Related Information

    For more information about this AD, contact Sanjay Ralhan, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; phone and 
fax: 206-231-3223.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Aviation Safety Agency (EASA) AD 2018-0155, dated 
July 20, 2018.
    (ii) [Reserved]
    (3) For information about EASA AD 2018-0155, contact the EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 221 89990 
6017; email: [email protected]; Internet: www.easa.europa.eu. You 
may find this EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this material at the FAA, Transport Standards 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195. This 
material may be found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2019-0667.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email: 
[email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Des Moines, Washington, on November 6, 2019.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-25605 Filed 11-25-19; 8:45 am]
BILLING CODE 4910-13-P

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.