Airworthiness Directives; Airbus SAS Airplanes, 19891-19893 [2019-09257]

Download as PDF Federal Register / Vol. 84, No. 88 / Tuesday, May 7, 2019 / Proposed Rules jbell on DSK3GLQ082PROD with PROPOSALS is ‘‘Within 30 months after May 16, 2016 (the effective date of AD 2016–07–22).’’ (3) Where paragraph (3) of EASA AD 2019– 0014 specifies a date of ‘‘06 September 2016,’’ for this AD, use ‘‘May 16, 2016 (the effective date of AD 2016–07–22).’’ (4) For Group 1 and 3 airplanes: This paragraph provides credit for actions required by paragraph (1) of EASA AD 2019– 0014, if those actions were performed before the effective date of this AD using Airbus Service Bulletin A300–24–6103, Revision 03, dated July 3, 2015, provided that the additional work specified in paragraphs (6) and (7) of EASA AD 2019–0014 is accomplished. (5) The ‘‘Remarks’’ section of EASA AD 2019–0014 does not apply to this AD. (i) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (j)(2) of this AD. Information may be emailed to: 9–ANM–116–AMOC– REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS’s EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOAauthorized signature. (3) Required for Compliance (RC): For any service information referenced in EASA AD 2019–0014 that contains RC procedures and tests: Except as required by paragraph (i)(2) of this AD, RC procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator’s maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (j) Related Information (1) For information about EASA AD 2019– 0014, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 89990 6017; email ADs@easa.europa.eu; Internet www.easa.europa.eu. You may find VerDate Sep<11>2014 16:04 May 06, 2019 Jkt 247001 this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this EASA AD at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. EASA AD 2019–0014 may be found in the AD docket on the internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2019–0253. (2) For more information about this AD, contact Dan Rodina, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206– 231–3225. Issued in Des Moines, Washington, on April 25, 2019. Michael Kaszycki, Acting Director, System Oversight Division, Aircraft Certification Service. [FR Doc. 2019–09266 Filed 5–6–19; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2019–0255; Product Identifier 2019–NM–018–AD] RIN 2120–AA64 Airworthiness Directives; Airbus SAS Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for all Airbus SAS Model A330–200 Freighter series airplanes. This proposed AD was prompted by reports of cracked flexible hoses of the oxygen crew and courier distribution system (OCCDS) on A330 freighter airplanes. This proposed AD would require repetitive detailed inspections, including functional testing, of the OCCDS and replacement of affected part(s) if necessary, as specified in an European Aviation Safety Agency (EASA) AD, which will be incorporated by reference. We are proposing this AD to address the unsafe condition on these products. DATES: We must receive comments on this proposed AD by June 21, 2019. ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. SUMMARY: PO 00000 Frm 00013 Fmt 4702 Sfmt 4702 19891 • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE, Washington, DC 20590. • Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For the incorporation by reference (IBR) material described in the ‘‘Related IBR material under 1 CFR part 51’’ section in SUPPLEMENTARY INFORMATION, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 89990 1000; email ADs@ easa.europa.eu; internet www.easa.europa.eu. You may find this IBR material on the EASA website at https://ad.easa.europa.eu. You may view this IBR material at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. It is also available in the AD docket on the internet at https:// www.regulations.gov. Examining the AD Docket You may examine the AD docket on the internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2019– 0255; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the regulatory evaluation, any comments received, and other information. The street address for Docket Operations (telephone 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206–231–3229. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA– 2019–0255; Product Identifier 2019– NM–018–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this NPRM. We will consider all comments received by the closing date and may amend this NPRM based on those comments. E:\FR\FM\07MYP1.SGM 07MYP1 19892 Federal Register / Vol. 84, No. 88 / Tuesday, May 7, 2019 / Proposed Rules We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this NPRM. Discussion The EASA, which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2019–0027, dated February 4, 2019 (‘‘EASA AD 2019–0027’’) (also referred to as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition for all Airbus SAS Model A330–200 Freighter series airplanes. The MCAI states: Several occurrences were reported of finding cracked flexible hoses [part number] P/N 32209-series of the OCCDS on A330 freighter aeroplanes. These flexible hoses are steel braided hoses with polyurethane (PUR) inner tubes and steel inner springs. On A330 freighter aeroplanes, these hoses are located in the courier area and are not pressurized during normal operation. This condition, if not detected and corrected, could lead to oxygen leakage in the flexible hose of the OCCDS, which, in combination with in-flight depressurization, smoke in cockpit or smoke evacuation procedure, could possibly result in cockpit crew injury and reduced control of the aeroplane. To address this potential unsafe condition, Airbus issued the SB [service bulletin] to provide inspection instructions. For the reasons described above, this [EASA] AD requires repetitive detailed inspections (DET), including functional testing, of the OCCDS and, depending on findings, replacement of affected part(s). previously, as incorporated by reference, except for any differences identified as exceptions in the regulatory text of this AD. Related IBR Material Under 1 CFR Part 51 EASA AD 2019–0027 describes procedures for repetitive inspections and replacement of OCCDS flexible hoses. This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section, and it is publicly available through the EASA website. Explanation of Required Compliance Information FAA’s Determination and Requirements of This Proposed AD This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design. Proposed Requirements of This NPRM This proposed AD would require accomplishing the actions specified in EASA AD 2019–0027 described In the FAA’s ongoing efforts to improve the efficiency of the AD process, the FAA worked with Airbus and EASA to develop a process to use certain EASA ADs as the primary source of information for compliance with requirements for corresponding FAA ADs. As a result, EASA AD 2019–0027 will be incorporated by reference in the FAA final rule. This proposed AD would, therefore, require compliance with the provisions specified in EASA AD 2019–0027, except for any differences identified as exceptions in the regulatory text of this proposed AD. Service information specified in EASA AD 2019–0027 that is required for compliance with EASA AD 2019–0027 will be available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2019– 0255 after the FAA final rule is published. Costs of Compliance We estimate that this proposed AD affects 5 airplanes of U.S. registry. We estimate the following costs to comply with this proposed AD: ESTIMATED COSTS FOR REQUIRED ACTIONS Labor cost 14 work-hours × $85 per hour = $1,190 ..................................................................................... According to the manufacturer, some or all of the costs of this proposed AD may be covered under warranty, thereby reducing the cost impact on affected individuals. We do not control warranty coverage for affected individuals. As a result, we have included all known costs in our cost estimate. jbell on DSK3GLQ082PROD with PROPOSALS Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ‘‘General requirements.’’ Under that VerDate Sep<11>2014 16:04 May 06, 2019 Jkt 247001 section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. This proposed AD is issued in accordance with authority delegated by the Executive Director, Aircraft Certification Service, as authorized by FAA Order 8000.51C. In accordance with that order, issuance of ADs is normally a function of the Compliance and Airworthiness Division, but during this transition period, the Executive Director has delegated the authority to issue ADs applicable to transport PO 00000 Cost per product Parts cost Frm 00014 Fmt 4702 Sfmt 4702 $0 $1,190 Cost on U.S. operators $5,950 category airplanes and associated appliances to the Director of the System Oversight Division. Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); E:\FR\FM\07MYP1.SGM 07MYP1 Federal Register / Vol. 84, No. 88 / Tuesday, May 7, 2019 / Proposed Rules 3. Will not affect intrastate aviation in Alaska; and 4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ Airbus SAS: Docket No. FAA–2019–0255; Product Identifier 2019–NM–018–AD. (a) Comments Due Date We must receive comments by June 21, 2019. (b) Affected ADs None. (c) Applicability This AD applies to all Airbus SAS Model A330–223F and -243F airplanes, certificated in any category. (d) Subject Air Transport Association (ATA) of America Code 35, Oxygen. jbell on DSK3GLQ082PROD with PROPOSALS (e) Reason This AD was prompted by reports of cracked flexible hoses of the oxygen crew and courier distribution system (OCCDS) on A330 freighter airplanes. We are issuing this AD to address cracked oxygen hoses. This condition, if not addressed, could lead to oxygen leakage in the flexible hose of the OCCDS, which, in combination with in-flight depressurization, smoke in the flight deck, or a smoke evacuation procedure, could result in crew injury and reduced control of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Aviation Safety VerDate Sep<11>2014 16:04 May 06, 2019 Jkt 247001 Agency (EASA) AD 2019–0027, dated February 4, 2019 (‘‘EASA AD 2019–0027’’). (h) Exceptions to EASA AD 2019–0027 (1) For purposes of determining compliance with the requirements of this AD: Where EASA AD 2019–0027 refers to its effective date, this AD requires using the effective date of this AD. (2) The ‘‘Remarks’’ section of EASA AD 2019–0027 does not apply to this AD. (i) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (j)(2) of this AD. Information may be emailed to: 9-ANM-116-AMOCREQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS’s EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOAauthorized signature. (3) Required for Compliance (RC): For any service information referenced in EASA AD 2019–0027 that contains RC procedures and tests: Except as required by paragraph (i)(2) of this AD, RC procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator’s maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (j) Related Information (1) For information about EASA AD 2019– 0027, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 89990 6017; email ADs@easa.europa.eu; Internet www.easa.europa.eu. You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this EASA AD at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. EASA AD 2019–0027 may be found in the AD docket on the internet at https:// PO 00000 Frm 00015 Fmt 4702 Sfmt 4702 19893 www.regulations.gov by searching for and locating Docket No. FAA–2019–0255. (2) For more information about this AD, contact Vladimir Ulyanov, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206–231–3229. Issued in Des Moines, Washington, on April 25, 2019. Michael Kaszycki, Acting Director, System Oversight Division, Aircraft Certification Service. [FR Doc. 2019–09257 Filed 5–6–19; 8:45 am] BILLING CODE 4910–13–P ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 and 81 [EPA–HQ–OAR–2018–0226; FRL–9993–32– Region 3] National Ambient Air Quality Standards: Determinations of Attainment, Extensions of the Attainment Date, and Reclassification of Several Areas Classified as Moderate for the 2008 Ozone Standards; Supplemental Proposal; Baltimore, Maryland Area Exceptional Events Environmental Protection Agency (EPA). ACTION: Proposed rule; reopening of comment period; availability of supplemental information. AGENCY: On November 14, 2018, the Environmental Protection Agency (EPA) proposed several actions related to the attainment date for 11 areas classified as ‘‘Moderate’’ for the 2008 ozone National Ambient Air Quality Standards (NAAQS), including proposing to determine that the Baltimore, Maryland nonattainment area (Baltimore Area) attained the standard by the July 20, 2018 attainment date. Under the statute, EPA must determine whether ozone nonattainment areas attained the NAAQS by the attainment date, and, within six months of the attainment date, publish a document in the Federal Register identifying each area that is determined as having failed to attain and identifying the reclassification. EPA is re-opening the comment period for the proposed rule published on November 14, 2018, but only with respect to EPA’s proposed determination for the Baltimore Area, because EPA erroneously omitted documents related to the State of Maryland’s exceptional events (EE) demonstration related to the 2016 Canadian wildfires, and in the proposal SUMMARY: E:\FR\FM\07MYP1.SGM 07MYP1

Agencies

[Federal Register Volume 84, Number 88 (Tuesday, May 7, 2019)]
[Proposed Rules]
[Pages 19891-19893]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-09257]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0255; Product Identifier 2019-NM-018-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for all 
Airbus SAS Model A330-200 Freighter series airplanes. This proposed AD 
was prompted by reports of cracked flexible hoses of the oxygen crew 
and courier distribution system (OCCDS) on A330 freighter airplanes. 
This proposed AD would require repetitive detailed inspections, 
including functional testing, of the OCCDS and replacement of affected 
part(s) if necessary, as specified in an European Aviation Safety 
Agency (EASA) AD, which will be incorporated by reference. We are 
proposing this AD to address the unsafe condition on these products.

DATES: We must receive comments on this proposed AD by June 21, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For the incorporation by reference (IBR) material described in the 
``Related IBR material under 1 CFR part 51'' section in SUPPLEMENTARY 
INFORMATION, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, 
Germany; telephone +49 221 89990 1000; email [email protected]; 
internet www.easa.europa.eu. You may find this IBR material on the EASA 
website at https://ad.easa.europa.eu. You may view this IBR material at 
the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, 
WA. For information on the availability of this material at the FAA, 
call 206-231-3195. It is also available in the AD docket on the 
internet at https://www.regulations.gov.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0255; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations (telephone 800-
647-5527) is in the ADDRESSES section. Comments will be available in 
the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3229.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2019-0255; 
Product Identifier 2019-NM-018-AD'' at the beginning of your comments. 
We specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this NPRM. We will consider all 
comments received by the closing date and may amend this NPRM based on 
those comments.

[[Page 19892]]

    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this NPRM.

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2019-0027, dated February 4, 2019 
(``EASA AD 2019-0027'') (also referred to as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for all Airbus SAS Model A330-200 Freighter series airplanes. 
The MCAI states:

    Several occurrences were reported of finding cracked flexible 
hoses [part number] P/N 32209-series of the OCCDS on A330 freighter 
aeroplanes. These flexible hoses are steel braided hoses with 
polyurethane (PUR) inner tubes and steel inner springs. On A330 
freighter aeroplanes, these hoses are located in the courier area 
and are not pressurized during normal operation.
    This condition, if not detected and corrected, could lead to 
oxygen leakage in the flexible hose of the OCCDS, which, in 
combination with in-flight depressurization, smoke in cockpit or 
smoke evacuation procedure, could possibly result in cockpit crew 
injury and reduced control of the aeroplane.
    To address this potential unsafe condition, Airbus issued the SB 
[service bulletin] to provide inspection instructions.
    For the reasons described above, this [EASA] AD requires 
repetitive detailed inspections (DET), including functional testing, 
of the OCCDS and, depending on findings, replacement of affected 
part(s).

Related IBR Material Under 1 CFR Part 51

    EASA AD 2019-0027 describes procedures for repetitive inspections 
and replacement of OCCDS flexible hoses. This material is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section, and it is publicly available through the EASA 
website.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI referenced 
above. We are proposing this AD because we evaluated all pertinent 
information and determined an unsafe condition exists and is likely to 
exist or develop on other products of the same type design.

Proposed Requirements of This NPRM

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2019-0027 described previously, as incorporated by 
reference, except for any differences identified as exceptions in the 
regulatory text of this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA worked with Airbus and EASA to develop a process to 
use certain EASA ADs as the primary source of information for 
compliance with requirements for corresponding FAA ADs. As a result, 
EASA AD 2019-0027 will be incorporated by reference in the FAA final 
rule. This proposed AD would, therefore, require compliance with the 
provisions specified in EASA AD 2019-0027, except for any differences 
identified as exceptions in the regulatory text of this proposed AD. 
Service information specified in EASA AD 2019-0027 that is required for 
compliance with EASA AD 2019-0027 will be available on the internet at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2019-0255 after the FAA final rule is published.

Costs of Compliance

    We estimate that this proposed AD affects 5 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on  U.S.
                           Labor cost                               Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
14 work-hours x $85 per hour = $1,190...........................              $0          $1,190          $5,950
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some or all of the costs of this 
proposed AD may be covered under warranty, thereby reducing the cost 
impact on affected individuals. We do not control warranty coverage for 
affected individuals. As a result, we have included all known costs in 
our cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes and associated appliances to the 
Director of the System Oversight Division.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);

[[Page 19893]]

    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Airbus SAS: Docket No. FAA-2019-0255; Product Identifier 2019-NM-
018-AD.

(a) Comments Due Date

    We must receive comments by June 21, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Airbus SAS Model A330-223F and -243F 
airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 35, Oxygen.

(e) Reason

    This AD was prompted by reports of cracked flexible hoses of the 
oxygen crew and courier distribution system (OCCDS) on A330 
freighter airplanes. We are issuing this AD to address cracked 
oxygen hoses. This condition, if not addressed, could lead to oxygen 
leakage in the flexible hose of the OCCDS, which, in combination 
with in-flight depressurization, smoke in the flight deck, or a 
smoke evacuation procedure, could result in crew injury and reduced 
control of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Aviation Safety Agency (EASA) AD 2019-
0027, dated February 4, 2019 (``EASA AD 2019-0027'').

(h) Exceptions to EASA AD 2019-0027

    (1) For purposes of determining compliance with the requirements 
of this AD: Where EASA AD 2019-0027 refers to its effective date, 
this AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2019-0027 does not apply 
to this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (j)(2) of this AD. Information 
may be emailed to: [email protected]. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's 
EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): For any service information 
referenced in EASA AD 2019-0027 that contains RC procedures and 
tests: Except as required by paragraph (i)(2) of this AD, RC 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures and tests identified as 
RC can be done and the airplane can be put back in an airworthy 
condition. Any substitutions or changes to procedures or tests 
identified as RC require approval of an AMOC.

(j) Related Information

    (1) For information about EASA AD 2019-0027, contact EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
89990 6017; email [email protected]; Internet www.easa.europa.eu. 
You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this EASA AD at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 
206-231-3195. EASA AD 2019-0027 may be found in the AD docket on the 
internet at https://www.regulations.gov by searching for and locating 
Docket No. FAA-2019-0255.
    (2) For more information about this AD, contact Vladimir 
Ulyanov, Aerospace Engineer, International Section, Transport 
Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; 
telephone and fax 206-231-3229.

    Issued in Des Moines, Washington, on April 25, 2019.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-09257 Filed 5-6-19; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.