Airworthiness Directives; The Boeing Company Airplanes, 3288-3290 [2019-01520]

Download as PDF 3288 Federal Register / Vol. 84, No. 29 / Tuesday, February 12, 2019 / Rules and Regulations displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120–0056. Public reporting for this collection of information is estimated to be approximately 1 hour per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave. SW, Washington, DC 20591, Attn: Information Collection Clearance Officer, AES–200. (l) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (m)(2) of this AD. Information may be emailed to: 9-ANM-116-AMOCREQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or the EASA; or Airbus SAS’s EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): Except as required by paragraph (i) of this AD, if any service information contains procedures or procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator’s maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC. (m) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD 2018–0102, dated April 27, 2018, for related information. This MCAI may be found in the AD docket on the internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2018–0705. (2) For more information about this AD, contact Sanjay Ralhan, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des VerDate Sep<11>2014 16:31 Feb 11, 2019 Jkt 247001 Moines, WA 98198; phone and fax: 206–231– 3223. (3) Service information identified in this AD that is not incorporated by reference is available at the addresses specified in paragraphs (n)(3) and (n)(4) of this AD. (n) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) Airbus Service Bulletin A320–57–1167, Revision 02, dated August 14, 2018. (ii) [Reserved] (3) For service information identified in this AD, contact Airbus SAS, Airworthiness Office—EIAS, Rond-Point Emile Dewoitine No: 2, 31700 Blagnac Cedex, France; phone: +33 5 61 93 36 96; fax: +33 5 61 93 44 51; email: account.airworth-eas@airbus.com; internet: https://www.airbus.com. (4) You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https:// www.archives.gov/federal-register/cfr/ibrlocations.html.; Issued in Des Moines, Washington, on January 10, 2019. Jeffrey E. Duven, Director, System Oversight Division, Aircraft Certification Service. [FR Doc. 2019–01522 Filed 2–11–19; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2018–0793; Product Identifier 2018–NM–057–AD; Amendment 39–19545; AD 2019–01–06] RIN 2120–AA64 Airworthiness Directives; The Boeing Company Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Final rule. AGENCY: We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737–100, –200, –200C, –300, –400, and –500 series airplanes. This AD was prompted by a report of cracks in a certain body station (STA) frame web and doubler at fastener SUMMARY: PO 00000 Frm 00004 Fmt 4700 Sfmt 4700 holes common to the stop fitting at a certain stringer. This AD requires repetitive surface high frequency eddy current (HFEC) inspections for cracking of the frame web and doubler at the stop fitting at a certain stringer, and applicable on-condition actions. We are issuing this AD to address the unsafe condition on these products. DATES: This AD is effective March 19, 2019. The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of March 19, 2019. ADDRESSES: For service information identified in this final rule, contact Boeing Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110–SK57, Seal Beach, CA 90740–5600; phone: 562–797–1717; internet: https:// www.myboeingfleet.com. You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. It is also available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2018– 0793. Examining the AD Docket You may examine the AD docket on the internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2018– 0793; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, the regulatory evaluation, any comments received, and other information. The address for Docket Operations (phone: 800–647–5527) is U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE, Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Galib Abumeri, Aerospace Engineer, Airframe Section, FAA, Los Angeles ACO Branch, 3960 Paramount Boulevard, Lakewood, CA 90712–4137; phone: 562–627–5324; fax: 562–627– 5210; email: galib.abumeri@faa.gov. SUPPLEMENTARY INFORMATION: Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to all The Boeing Company Model 737–100, –200, –200C, –300, –400, and –500 series airplanes. The NPRM published in the Federal Register on E:\FR\FM\12FER1.SGM 12FER1 Federal Register / Vol. 84, No. 29 / Tuesday, February 12, 2019 / Rules and Regulations September 17, 2018 (83 FR 46902). The NPRM was prompted by a report of cracks in the STA 303.9 frame web and doubler at fastener holes common to the stop fitting at stringer 16 left (S–16L). The NPRM proposed to require repetitive surface HFEC inspections for cracking of the STA 303.9 frame web and doubler at the stop fitting at S–16L, and applicable on-condition actions. We are issuing this AD to address cracks in the STA 303.9 frame web and doubler at the stop fitting at S–16L, which, if not addressed, could result in the inability of a principal structural element to sustain limit loads and possible rapid decompression of the airplane. Effect of Winglets on Accomplishment of the Proposed Actions Aviation Partners Boeing stated that accomplishing Supplemental Type Certificate (STC) ST01219SE does not affect the actions specified in the NPRM. We concur with the commenter. We have redesignated paragraph (c) of the proposed AD as paragraph (c)(1) of this AD and added paragraph (c)(2) to this AD to state that installation of STC ST01219SE does not affect the ability to accomplish the actions required by this AD. Therefore, for airplanes on which STC ST01219SE is installed, a ‘‘change in product’’ alternative method of compliance (AMOC) approval request is not necessary to comply with the requirements of 14 CFR 39.17. Comments We gave the public the opportunity to participate in developing this final rule. The following presents the comments received on the NPRM and the FAA’s response to each comment. Conclusion We reviewed the relevant data, considered the comments received, and determined that air safety and the public interest require adopting this final rule with the changes described previously and minor editorial changes. We have determined that these minor changes: Support for the NPRM Boeing concurred with the NPRM. 3289 • Are consistent with the intent that was proposed in the NPRM for addressing the unsafe condition; and • Do not add any additional burden upon the public than was already proposed in the NPRM. We also determined that these changes will not increase the economic burden on any operator or increase the scope of this final rule. Related Service Information Under 1 CFR Part 51 We reviewed Boeing Requirements Bulletin 737–53A1375 RB, dated March 12, 2018. The service information describes procedures for repetitive surface HFEC inspections for cracking of the STA 303.9 frame web and doubler at the stop fitting at S–16L, and applicable on-condition actions. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section. Costs of Compliance We estimate that this AD affects 67 airplanes of U.S. registry. We estimate the following costs to comply with this AD: ESTIMATED COSTS FOR REQUIRED ACTIONS Action Labor cost HFEC Inspections ............... 13 work-hours × $85 per hour = $1,105 per inspection cycle. We have received no definitive data that would enable us to provide cost estimates for the on-condition actions specified in this AD. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on VerDate Sep<11>2014 16:31 Feb 11, 2019 Jkt 247001 Parts cost Cost per product $0 $1,105 per inspection cycle products identified in this rulemaking action. This AD is issued in accordance with authority delegated by the Executive Director, Aircraft Certification Service, as authorized by FAA Order 8000.51C. In accordance with that order, issuance of ADs is normally a function of the Compliance and Airworthiness Division, but during this transition period, the Executive Director has delegated the authority to issue ADs applicable to transport category airplanes and associated appliances to the Director of the System Oversight Division. Regulatory Findings This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. PO 00000 Frm 00005 Fmt 4700 Sfmt 4700 Cost on U.S. operators $74,035 per inspection cycle. For the reasons discussed above, I certify that this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Is not a ‘‘significant rule’’ under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), (3) Will not affect intrastate aviation in Alaska, and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: E:\FR\FM\12FER1.SGM 12FER1 3290 Federal Register / Vol. 84, No. 29 / Tuesday, February 12, 2019 / Rules and Regulations PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ 2019–01–06 The Boeing Company: Amendment 39–19545; Docket No. FAA–2018–0793; Product Identifier 2018–NM–057–AD. (i) Exceptions to Service Information Specifications (a) Effective Date This AD is effective March 19, 2019. (b) Affected ADs None. (c) Applicability (1) This AD applies to all The Boeing Company Model 737–100, –200, –200C, –300, –400, and –500 series airplanes, certificated in any category. (2) Installation of Supplemental Type Certificate (STC) ST01219SE does not affect the ability to accomplish the actions required by this AD. Therefore, for airplanes on which STC ST01219SE is installed, a ‘‘change in product’’ alternative method of compliance (AMOC) approval request is not necessary to comply with the requirements of 14 CFR 39.17. (d) Subject Air Transport Association (ATA) of America Code 53, Fuselage. (e) Unsafe Condition This AD was prompted by a report of cracks in the body station (STA) 303.9 frame web and doubler at fastener holes common to the stop fitting at stringer 16 left (S–16L). We are issuing this AD to address cracks in the STA 303.9 frame web and doubler at the stop fitting at S–16L, which, if not addressed, could result in the inability of a principal structural element to sustain limit loads and possible rapid decompression of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Required Actions for Group 1 For airplanes identified as Group 1 in Boeing Requirements Bulletin 737–53A1375 RB, dated March 12, 2018: Within 120 days after the effective date of this AD, inspect the airplane and do all applicable on-condition actions using a method approved in accordance with the procedures specified in paragraph (j) of this AD. (h) Required Actions for Groups 2 Through 5 Except as specified in paragraph (i) of this AD: For airplanes identified as Groups 2 through 5 in Boeing Requirements Bulletin 737–53A1375 RB, dated March 12, 2018, at the applicable times specified in the VerDate Sep<11>2014 16:31 Feb 11, 2019 Jkt 247001 ‘‘Compliance’’ paragraph of Boeing Requirements Bulletin 737–53A1375 RB, dated March 12, 2018, do all applicable actions identified in, and in accordance with, the Accomplishment Instructions of Boeing Requirements Bulletin 737–53A1375 RB, dated March 12, 2018. Note 1 to paragraph (h) of this AD: Guidance for accomplishing the actions required by this AD can be found in Boeing Alert Service Bulletin 737–53A1375, dated March 12, 2018, which is referred to in Boeing Requirements Bulletin 737–53A1375 RB, dated March 12, 2018. (1) For purposes of determining compliance with the requirements of this AD: Where Boeing Requirements Bulletin 737– 53A1375 RB, dated March 12, 2018, uses the phrase ‘‘the original issue date of Requirements Bulletin 737–53A1375 RB,’’ this AD requires using ‘‘the effective date of this AD.’’ (2) Where Boeing Requirements Bulletin 737–53A1375 RB, dated March 12, 2018, specifies contacting Boeing for repair instructions, this AD requires repair using a method approved in accordance with the procedures specified in paragraph (j) of this AD. (j) Alternative Methods of Compliance (AMOCs) (1) The Manager, Los Angeles ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (k) of this AD. Information may be emailed to: 9-ANMLAACO-AMOC-Requests@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. (3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Los Angeles ACO Branch, FAA, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. (k) Related Information For more information about this AD, contact Galib Abumeri, Aerospace Engineer, Airframe Section, FAA, Los Angeles ACO Branch, 3960 Paramount Boulevard, Lakewood, CA 90712–4137; phone: 562–627– 5324; fax: 562–627–5210; email: galib.abumeri@faa.gov. PO 00000 Frm 00006 Fmt 4700 Sfmt 4700 (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Boeing Requirements Bulletin 737– 53A1375 RB, dated March 12, 2018. (ii) [Reserved]. (3) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110–SK57, Seal Beach, CA 90740–5600; phone: 562–797–1717; internet: https:// www.myboeingfleet.com. (4) You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https:// www.archives.gov/federal-register/cfr/ibrlocations.html. Issued in Des Moines, Washington, on January 10, 2019. Jeffrey E. Duven, Director, System Oversight Division, Aircraft Certification Service. [FR Doc. 2019–01520 Filed 2–11–19; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2018–0162; Product Identifier 2017–NM–116–AD; Amendment 39–19542; AD 2019–01–03] RIN 2120–AA64 Airworthiness Directives; the Boeing Company Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Final rule. AGENCY: We are superseding Airworthiness Directive (AD) 2016–18– 01, which applied to certain The Boeing Company Model 737–600, –700, –700C, –800, –900, and –900ER series airplanes. AD 2016–18–01 required repetitive lubrication of the forward and aft trunnion pin assemblies of the right and left main landing gears (MLGs); repetitive inspection of these assemblies for corrosion and chrome damage, and related investigative and corrective actions if necessary; and installation of SUMMARY: E:\FR\FM\12FER1.SGM 12FER1

Agencies

[Federal Register Volume 84, Number 29 (Tuesday, February 12, 2019)]
[Rules and Regulations]
[Pages 3288-3290]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-01520]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0793; Product Identifier 2018-NM-057-AD; Amendment 
39-19545; AD 2019-01-06]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for all The 
Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series 
airplanes. This AD was prompted by a report of cracks in a certain body 
station (STA) frame web and doubler at fastener holes common to the 
stop fitting at a certain stringer. This AD requires repetitive surface 
high frequency eddy current (HFEC) inspections for cracking of the 
frame web and doubler at the stop fitting at a certain stringer, and 
applicable on-condition actions. We are issuing this AD to address the 
unsafe condition on these products.

DATES: This AD is effective March 19, 2019.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of March 19, 
2019.

ADDRESSES: For service information identified in this final rule, 
contact Boeing Commercial Airplanes, Attention: Contractual & Data 
Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 
90740-5600; phone: 562-797-1717; internet: https://www.myboeingfleet.com. You may view this service information at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. 
For information on the availability of this material at the FAA, call 
206-231-3195. It is also available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0793.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0793; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, the regulatory evaluation, any comments received, and 
other information. The address for Docket Operations (phone: 800-647-
5527) is U.S. Department of Transportation, Docket Operations, M-30, 
West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, 
Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Galib Abumeri, Aerospace Engineer, 
Airframe Section, FAA, Los Angeles ACO Branch, 3960 Paramount 
Boulevard, Lakewood, CA 90712-4137; phone: 562-627-5324; fax: 562-627-
5210; email: galib.abumeri@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to all The Boeing Company 
Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. The 
NPRM published in the Federal Register on

[[Page 3289]]

September 17, 2018 (83 FR 46902). The NPRM was prompted by a report of 
cracks in the STA 303.9 frame web and doubler at fastener holes common 
to the stop fitting at stringer 16 left (S-16L). The NPRM proposed to 
require repetitive surface HFEC inspections for cracking of the STA 
303.9 frame web and doubler at the stop fitting at S-16L, and 
applicable on-condition actions.
    We are issuing this AD to address cracks in the STA 303.9 frame web 
and doubler at the stop fitting at S-16L, which, if not addressed, 
could result in the inability of a principal structural element to 
sustain limit loads and possible rapid decompression of the airplane.

Comments

    We gave the public the opportunity to participate in developing 
this final rule. The following presents the comments received on the 
NPRM and the FAA's response to each comment.

Support for the NPRM

    Boeing concurred with the NPRM.

Effect of Winglets on Accomplishment of the Proposed Actions

    Aviation Partners Boeing stated that accomplishing Supplemental 
Type Certificate (STC) ST01219SE does not affect the actions specified 
in the NPRM.
    We concur with the commenter. We have redesignated paragraph (c) of 
the proposed AD as paragraph (c)(1) of this AD and added paragraph 
(c)(2) to this AD to state that installation of STC ST01219SE does not 
affect the ability to accomplish the actions required by this AD. 
Therefore, for airplanes on which STC ST01219SE is installed, a 
``change in product'' alternative method of compliance (AMOC) approval 
request is not necessary to comply with the requirements of 14 CFR 
39.17.

Conclusion

    We reviewed the relevant data, considered the comments received, 
and determined that air safety and the public interest require adopting 
this final rule with the changes described previously and minor 
editorial changes. We have determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for addressing the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM.
    We also determined that these changes will not increase the 
economic burden on any operator or increase the scope of this final 
rule.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Requirements Bulletin 737-53A1375 RB, dated 
March 12, 2018. The service information describes procedures for 
repetitive surface HFEC inspections for cracking of the STA 303.9 frame 
web and doubler at the stop fitting at S-16L, and applicable on-
condition actions. This service information is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in the ADDRESSES section.

Costs of Compliance

    We estimate that this AD affects 67 airplanes of U.S. registry. We 
estimate the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
             Action                     Labor cost          Parts cost     Cost per product        operators
----------------------------------------------------------------------------------------------------------------
HFEC Inspections...............  13 work-hours x $85 per              $0  $1,105 per          $74,035 per
                                  hour = $1,105 per                        inspection cycle.   inspection cycle.
                                  inspection cycle.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to transport category airplanes and 
associated appliances to the Director of the System Oversight Division.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

[[Page 3290]]

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2019-01-06 The Boeing Company: Amendment 39-19545; Docket No. FAA-
2018-0793; Product Identifier 2018-NM-057-AD.

(a) Effective Date

    This AD is effective March 19, 2019.

(b) Affected ADs

    None.

(c) Applicability

    (1) This AD applies to all The Boeing Company Model 737-100, -
200, -200C, -300, -400, and -500 series airplanes, certificated in 
any category.
    (2) Installation of Supplemental Type Certificate (STC) 
ST01219SE does not affect the ability to accomplish the actions 
required by this AD. Therefore, for airplanes on which STC ST01219SE 
is installed, a ``change in product'' alternative method of 
compliance (AMOC) approval request is not necessary to comply with 
the requirements of 14 CFR 39.17.

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Unsafe Condition

    This AD was prompted by a report of cracks in the body station 
(STA) 303.9 frame web and doubler at fastener holes common to the 
stop fitting at stringer 16 left (S-16L). We are issuing this AD to 
address cracks in the STA 303.9 frame web and doubler at the stop 
fitting at S-16L, which, if not addressed, could result in the 
inability of a principal structural element to sustain limit loads 
and possible rapid decompression of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions for Group 1

    For airplanes identified as Group 1 in Boeing Requirements 
Bulletin 737-53A1375 RB, dated March 12, 2018: Within 120 days after 
the effective date of this AD, inspect the airplane and do all 
applicable on-condition actions using a method approved in 
accordance with the procedures specified in paragraph (j) of this 
AD.

(h) Required Actions for Groups 2 Through 5

    Except as specified in paragraph (i) of this AD: For airplanes 
identified as Groups 2 through 5 in Boeing Requirements Bulletin 
737-53A1375 RB, dated March 12, 2018, at the applicable times 
specified in the ``Compliance'' paragraph of Boeing Requirements 
Bulletin 737-53A1375 RB, dated March 12, 2018, do all applicable 
actions identified in, and in accordance with, the Accomplishment 
Instructions of Boeing Requirements Bulletin 737-53A1375 RB, dated 
March 12, 2018.
    Note 1 to paragraph (h) of this AD: Guidance for accomplishing 
the actions required by this AD can be found in Boeing Alert Service 
Bulletin 737-53A1375, dated March 12, 2018, which is referred to in 
Boeing Requirements Bulletin 737-53A1375 RB, dated March 12, 2018.

(i) Exceptions to Service Information Specifications

    (1) For purposes of determining compliance with the requirements 
of this AD: Where Boeing Requirements Bulletin 737-53A1375 RB, dated 
March 12, 2018, uses the phrase ``the original issue date of 
Requirements Bulletin 737-53A1375 RB,'' this AD requires using ``the 
effective date of this AD.''
    (2) Where Boeing Requirements Bulletin 737-53A1375 RB, dated 
March 12, 2018, specifies contacting Boeing for repair instructions, 
this AD requires repair using a method approved in accordance with 
the procedures specified in paragraph (j) of this AD.

(j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Los Angeles ACO Branch, FAA, has the authority 
to approve AMOCs for this AD, if requested using the procedures 
found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your 
request to your principal inspector or local Flight Standards 
District Office, as appropriate. If sending information directly to 
the manager of the certification office, send it to the attention of 
the person identified in paragraph (k) of this AD. Information may 
be emailed to: 9-ANM-LAACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Los Angeles ACO Branch, FAA, to make those findings. To be 
approved, the repair method, modification deviation, or alteration 
deviation must meet the certification basis of the airplane, and the 
approval must specifically refer to this AD.

(k) Related Information

    For more information about this AD, contact Galib Abumeri, 
Aerospace Engineer, Airframe Section, FAA, Los Angeles ACO Branch, 
3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 562-627-
5324; fax: 562-627-5210; email: galib.abumeri@faa.gov.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Boeing Requirements Bulletin 737-53A1375 RB, dated March 12, 
2018.
    (ii) [Reserved].
    (3) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; phone: 562-797-1717; internet: https://www.myboeingfleet.com.
    (4) You may view this service information at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 
206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Des Moines, Washington, on January 10, 2019.
Jeffrey E. Duven,
Director, System Oversight Division, Aircraft Certification Service.
[FR Doc. 2019-01520 Filed 2-11-19; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.