Airworthiness Directives; The Boeing Company Airplanes, 20288-20290 [2017-08708]

Download as PDF 20288 Proposed Rules Federal Register Vol. 82, No. 82 Monday, May 1, 2017 This section of the FEDERAL REGISTER contains notices to the public of the proposed issuance of rules and regulations. The purpose of these notices is to give interested persons an opportunity to participate in the rule making prior to the adoption of the final rules. DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2017–0330; Directorate Identifier 2017–NM–016–AD] RIN 2120–AA64 Examining the AD Docket Airworthiness Directives; The Boeing Company Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737–300, –400, and –500 series airplanes. This proposed AD would require repetitive inspections for cracking in the skin lap splice at the lower fastener row, and repair if necessary. This AD was prompted by an evaluation by the design approval holder (DAH) indicating that the lower skin at the skin lap splice lower fastener row is subject to widespread fatigue damage (WFD). We are proposing this AD to address the unsafe condition on these products. DATES: We must receive comments on this proposed AD by June 15, 2017. ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this NPRM, contact Boeing Commercial Airplanes, Attention: Contractual & Data mstockstill on DSK30JT082PROD with PROPOSALS SUMMARY: VerDate Sep<11>2014 16:54 Apr 28, 2017 Services (C&DS), 2600 Westminster Blvd., MC 110 SK57, Seal Beach, CA 90740–5600; telephone 562–797–1717; Internet https:// www.myboeingfleet.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Boeing Alert Service Bulletin 737–53A1365, dated January 23, 2017, is also available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2017–0330. Jkt 241001 You may examine the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2017– 0330; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (phone: 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: James Guo, Aerospace Engineer, Airframe Branch, ANM–120L, FAA, Los Angeles Aircraft Certification Office (ACO), 3960 Paramount Boulevard, Lakewood, CA 90712–4137; phone: 562–627–5357; fax: 562–627–5210; email: james.guo@faa.gov. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA– 2017–0330; Directorate Identifier 2017– NM–016–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD because of those comments. We will post all comments we receive, without change, to https:// PO 00000 Frm 00001 Fmt 4702 Sfmt 4702 www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion Fatigue damage can occur locally, in small areas or structural design details, or globally, in widespread areas. Multiple-site damage is widespread damage that occurs in a large structural element such as a single rivet line of a lap splice joining two large skin panels. Widespread damage can also occur in multiple elements such as adjacent frames or stringers. Multiple-site damage and multiple-element damage cracks are typically too small initially to be reliably detected with normal inspection methods. Without intervention, these cracks will grow, and eventually compromise the structural integrity of the airplane. This condition is known as WFD. It is associated with general degradation of large areas of structure with similar structural details and stress levels. As an airplane ages, WFD will likely occur, and will certainly occur if the airplane is operated long enough without any intervention. The FAA’s WFD final rule (75 FR 69746, November 15, 2010) became effective on January 14, 2011. The WFD rule requires certain actions to prevent structural failure due to WFD throughout the operational life of certain existing transport category airplanes and all of these airplanes that will be certificated in the future. For existing and future airplanes subject to the WFD rule, the rule requires that DAHs establish a limit of validity (LOV) of the engineering data that support the structural maintenance program. Operators affected by the WFD rule may not fly an airplane beyond its LOV, unless an extended LOV is approved. The WFD rule (75 FR 69746, November 15, 2010) does not require identifying and developing maintenance actions if the DAHs can show that such actions are not necessary to prevent WFD before the airplane reaches the LOV. Many LOVs, however, do depend on accomplishment of future maintenance actions. As stated in the WFD rule, any maintenance actions necessary to reach the LOV will be mandated by airworthiness directives through separate rulemaking actions. E:\FR\FM\01MYP1.SGM 01MYP1 Federal Register / Vol. 82, No. 82 / Monday, May 1, 2017 / Proposed Rules In the context of WFD, this action is necessary to enable DAHs to propose LOVs that allow operators the longest operational lives for their airplanes, and still ensure that WFD will not occur. This approach allows for an implementation strategy that provides flexibility to DAHs in determining the timing of service information development (with FAA approval), while providing operators with certainty regarding the LOV applicable to their airplanes. We received a report indicating that, during window belt replacements, cracking was found in the lower skin at the stringer S–14 lap splice lower row between station (STA) 360 and STA 540, and between STA 727 and STA 908, on a Model 737–300 airplane. An additional 51 airplanes were inspected and 22 crack indications were reported on airplanes with 42,358 to 48,188 total flight cycles and 53,490 to 58,796 total flight hours. We are issuing this AD to detect and correct cracks in the lower skin which, if not detected, could link up, resulting in reduced structural integrity of the airplane and consequent uncontrolled decompression of the airplane. Related Service Information Under 1 CFR Part 51 We reviewed Boeing Alert Service Bulletin 737–53A1365, dated January 23, 2017. The service information describes procedures for eddy current inspections for cracking at the skin lap splice in the lower fastener row, and repair if necessary. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section. FAA’s Determination We are proposing this AD because we evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop in other products of the same type design. Proposed AD Requirements This proposed AD would require accomplishing the actions specified in the service information described previously, except as discussed under ‘‘Differences Between this Proposed AD and the Service Information.’’ For information on the procedures and 20289 compliance times, see this service information at https:// www.regulations.gov by searching for and locating Docket No. FAA–2017– 0330. Differences Between This Proposed AD and the Service Information Boeing Alert Service Bulletin 737– 53A1365, dated January 23, 2017, specifies to contact the manufacturer for certain instructions, but this proposed AD would require using repair methods, modification deviations, and alteration deviations in one of the following ways: • In accordance with a method that we approve; or • Using data that meet the certification basis of the airplane, and that have been approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) whom we have authorized to make those findings. Costs of Compliance We estimate that this proposed AD affects 126 airplanes of U.S. registry. We estimate the following costs to comply with this proposed AD: ESTIMATED COSTS Action Labor cost Inspection ........ 84 work-hours × $85 per hour = $7,140 per inspection cycle. We have received no definitive data that would enable us to provide cost estimates for the on-condition actions specified in this proposed AD. mstockstill on DSK30JT082PROD with PROPOSALS Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. VerDate Sep<11>2014 16:54 Apr 28, 2017 Jkt 241001 Parts cost $0 Cost per product Cost on U.S. operators $7,140 per inspection cycle ... $899,640 per inspection cycle. Regulatory Findings List of Subjects in 14 CFR Part 39 We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), (3) Will not affect intrastate aviation in Alaska, and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. PO 00000 Frm 00002 Fmt 4702 Sfmt 4702 The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ The Boeing Company: Docket No. FAA– 2017–0330; Directorate Identifier 2017– NM–016–AD. (a) Comments Due Date We must receive comments by June 15, 2017. E:\FR\FM\01MYP1.SGM 01MYP1 20290 Federal Register / Vol. 82, No. 82 / Monday, May 1, 2017 / Proposed Rules (b) Affected ADs None. to the airplanes with the specified total flight cycles as of the effective date of this AD. (c) Applicability This AD applies to The Boeing Company Model 737–300, –400, –500 airplanes, certificated in any category, as identified in Boeing Alert Service Bulletin 737–53A1365, dated January 23, 2017. (j) Alternative Methods of Compliance (AMOCs) (1) The Manager, Los Angeles Aircraft Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in paragraph (k)(1) of this AD. Information may be emailed to: 9-ANM-LAACO-AMOCRequests@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. (3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Los Angeles ACO, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD. (4) Except as required by paragraph (h) of this AD: For service information that contains steps that are labeled as Required for Compliance (RC), the provisions of paragraphs (j)(4)(i) and (j)(4)(ii) of this AD apply. (i) The steps labeled as RC, including substeps under an RC step and any figures identified in an RC step, must be done to comply with the AD. If a step or substep is labeled ‘‘RC Exempt,’’ then the RC requirement is removed from that step or substep. An AMOC is required for any deviations to RC steps, including substeps and identified figures. (ii) Steps not labeled as RC may be deviated from using accepted methods in accordance with the operator’s maintenance or inspection program without obtaining approval of an AMOC, provided the RC steps, including substeps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition. (d) Subject Air Transport Association (ATA) of America Code 53; Fuselage. (e) Unsafe Condition This AD was prompted by an evaluation by the design approval holder indicating that the lower skin at the skin lap splice lower fastener row is subject to widespread fatigue damage. We are issuing this AD to detect and correct cracks in the lower skin, which, if not detected, could link up, resulting in reduced structural integrity of the airplane and consequent uncontrolled decompression of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Repetitive Inspections Except as provided by paragraph (i) of this AD, at the applicable time specified in paragraph 1.E., ‘‘Compliance,’’ of Boeing Alert Service Bulletin 737–53A1365, dated January 23, 2017: Do external eddy current inspections at stringer S–14 on the left and right sides of the airplane (S–14L and S–14R) for any crack in the skin lap splice at the lower fastener row, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 737–53A1365, dated January 23, 2017. Repeat the inspections thereafter at the applicable times specified in paragraph 1.E., ‘‘Compliance,’’ of Boeing Alert Service Bulletin 737–53A1365, dated January 23, 2017. mstockstill on DSK30JT082PROD with PROPOSALS (h) Repair If any crack is found during any inspection required by paragraph (g) of this AD, repair before further flight using a method approved in accordance with the procedures specified in paragraph (j) of this AD. Although Boeing Alert Service Bulletin 737–53A1365, dated January 23, 2017, specifies to contact Boeing for appropriate action and specifies that action as ‘‘RC’’ (Required for Compliance), this AD requires repair as specified in this paragraph. (i) Exceptions to Service Information Specifications (1) Where Boeing Alert Service Bulletin 737–53A1365, dated January 23, 2017, specifies a compliance time ‘‘after the original issue date of this service bulletin,’’ this AD requires compliance within the specified compliance time after the effective date of this AD. (2) The Condition column of Table 1 and Table 2 of paragraph 1.E., ‘‘Compliance,’’ of Boeing Alert Service Bulletin 737–53A1365, dated January 23, 2017, refers to total flight cycles ‘‘at the original issue date of this service bulletin.’’ This AD, however, applies VerDate Sep<11>2014 16:54 Apr 28, 2017 Jkt 241001 Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Issued in Renton, Washington, on April 24, 2017. Michael Kaszycki, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2017–08708 Filed 4–28–17; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 71 [Docket No. FAA–2017–0297; Airspace Docket No. 16–AWP–4] Proposed Establishment of Class E Airspace, Hawthorne, NV Federal Aviation Administration (FAA), DOT. ACTION: Notice of Proposed Rulemaking (NPRM). AGENCY: This action proposes to establish Class E airspace extending upward from 700 feet above the surface at Hawthorne Industrial Airport, Hawthorne, NV, to support the development of Instrument Flight Rules (IFR) operations under standard instrument approach and departure procedures at the airport, for the safety of aircraft and management of airspace within the National Airspace System. DATES: Comments must be received on or before June 15, 2017. ADDRESSES: Send comments on this proposal to the U.S. Department of Transportation, Docket Operations, 1200 New Jersey Avenue SE., West Building Ground Floor, Room W12–140, Washington, DC 20590; telephone: 1– 800–647–5527, or (202) 366–9826. You must identify FAA Docket No. FAA– 2017–0297; Airspace Docket No. 16– AWP–4, at the beginning of your comments. You may also submit comments through the Internet at https:// www.regulations.gov. (k) Related Information FAA Order 7400.11A, Airspace (1) For more information about this AD, Designations and Reporting Points, and contact James Guo, Aerospace Engineer, subsequent amendments can be viewed Airframe Branch, ANM–120L, FAA, Los online at https://www.faa.gov/air_traffic/ Angeles ACO, 3960 Paramount Boulevard, Lakewood, CA 90712–4137; phone: 562–627– publications/. For further information, 5357; fax: 562–627–5210; email: james.guo@ you can contact the Airspace Policy faa.gov. Group, Federal Aviation (2) For service information identified in Administration, 800 Independence this AD, contact Boeing Commercial Avenue SW., Washington, DC 20591; Airplanes, Attention: Contractual & Data telephone: 202–267–8783. The Order is Services (C&DS), 2600 Westminster Blvd., also available for inspection at the MC 110–SK57, Seal Beach, CA 90740–5600; National Archives and Records telephone 562–797–1717; Internet https:// Administration (NARA). For www.myboeingfleet.com. You may view this information on the availability of FAA referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Order 7400.11A at NARA, call 202–741– PO 00000 Frm 00003 Fmt 4702 Sfmt 4702 SUMMARY: E:\FR\FM\01MYP1.SGM 01MYP1

Agencies

[Federal Register Volume 82, Number 82 (Monday, May 1, 2017)]
[Proposed Rules]
[Pages 20288-20290]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2017-08708]


========================================================================
Proposed Rules
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains notices to the public of 
the proposed issuance of rules and regulations. The purpose of these 
notices is to give interested persons an opportunity to participate in 
the rule making prior to the adoption of the final rules.

========================================================================


Federal Register / Vol. 82, No. 82 / Monday, May 1, 2017 / Proposed 
Rules

[[Page 20288]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2017-0330; Directorate Identifier 2017-NM-016-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 737-300, -400, and -500 series 
airplanes. This proposed AD would require repetitive inspections for 
cracking in the skin lap splice at the lower fastener row, and repair 
if necessary. This AD was prompted by an evaluation by the design 
approval holder (DAH) indicating that the lower skin at the skin lap 
splice lower fastener row is subject to widespread fatigue damage 
(WFD). We are proposing this AD to address the unsafe condition on 
these products.

DATES: We must receive comments on this proposed AD by June 15, 2017.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110 SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; Internet https://www.myboeingfleet.com. You may 
view this referenced service information at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the 
availability of this material at the FAA, call 425-227-1221. Boeing 
Alert Service Bulletin 737-53A1365, dated January 23, 2017, is also 
available on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2017-0330.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2017-
0330; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: James Guo, Aerospace Engineer, 
Airframe Branch, ANM-120L, FAA, Los Angeles Aircraft Certification 
Office (ACO), 3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 
562-627-5357; fax: 562-627-5210; email: james.guo@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2017-0330; 
Directorate Identifier 2017-NM-016-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Fatigue damage can occur locally, in small areas or structural 
design details, or globally, in widespread areas. Multiple-site damage 
is widespread damage that occurs in a large structural element such as 
a single rivet line of a lap splice joining two large skin panels. 
Widespread damage can also occur in multiple elements such as adjacent 
frames or stringers. Multiple-site damage and multiple-element damage 
cracks are typically too small initially to be reliably detected with 
normal inspection methods. Without intervention, these cracks will 
grow, and eventually compromise the structural integrity of the 
airplane. This condition is known as WFD. It is associated with general 
degradation of large areas of structure with similar structural details 
and stress levels. As an airplane ages, WFD will likely occur, and will 
certainly occur if the airplane is operated long enough without any 
intervention.
    The FAA's WFD final rule (75 FR 69746, November 15, 2010) became 
effective on January 14, 2011. The WFD rule requires certain actions to 
prevent structural failure due to WFD throughout the operational life 
of certain existing transport category airplanes and all of these 
airplanes that will be certificated in the future. For existing and 
future airplanes subject to the WFD rule, the rule requires that DAHs 
establish a limit of validity (LOV) of the engineering data that 
support the structural maintenance program. Operators affected by the 
WFD rule may not fly an airplane beyond its LOV, unless an extended LOV 
is approved.
    The WFD rule (75 FR 69746, November 15, 2010) does not require 
identifying and developing maintenance actions if the DAHs can show 
that such actions are not necessary to prevent WFD before the airplane 
reaches the LOV. Many LOVs, however, do depend on accomplishment of 
future maintenance actions. As stated in the WFD rule, any maintenance 
actions necessary to reach the LOV will be mandated by airworthiness 
directives through separate rulemaking actions.

[[Page 20289]]

    In the context of WFD, this action is necessary to enable DAHs to 
propose LOVs that allow operators the longest operational lives for 
their airplanes, and still ensure that WFD will not occur. This 
approach allows for an implementation strategy that provides 
flexibility to DAHs in determining the timing of service information 
development (with FAA approval), while providing operators with 
certainty regarding the LOV applicable to their airplanes.
    We received a report indicating that, during window belt 
replacements, cracking was found in the lower skin at the stringer S-14 
lap splice lower row between station (STA) 360 and STA 540, and between 
STA 727 and STA 908, on a Model 737-300 airplane. An additional 51 
airplanes were inspected and 22 crack indications were reported on 
airplanes with 42,358 to 48,188 total flight cycles and 53,490 to 
58,796 total flight hours. We are issuing this AD to detect and correct 
cracks in the lower skin which, if not detected, could link up, 
resulting in reduced structural integrity of the airplane and 
consequent uncontrolled decompression of the airplane.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Service Bulletin 737-53A1365, dated 
January 23, 2017. The service information describes procedures for eddy 
current inspections for cracking at the skin lap splice in the lower 
fastener row, and repair if necessary. This service information is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
the ADDRESSES section.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information described previously, except as discussed 
under ``Differences Between this Proposed AD and the Service 
Information.'' For information on the procedures and compliance times, 
see this service information at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2017-0330.

Differences Between This Proposed AD and the Service Information

    Boeing Alert Service Bulletin 737-53A1365, dated January 23, 2017, 
specifies to contact the manufacturer for certain instructions, but 
this proposed AD would require using repair methods, modification 
deviations, and alteration deviations in one of the following ways:
     In accordance with a method that we approve; or
     Using data that meet the certification basis of the 
airplane, and that have been approved by the Boeing Commercial 
Airplanes Organization Designation Authorization (ODA) whom we have 
authorized to make those findings.

Costs of Compliance

    We estimate that this proposed AD affects 126 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
          Action                   Labor cost        Parts cost      Cost per product     Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Inspection................  84 work-hours x $85 per          $0  $7,140 per inspection    $899,640 per
                             hour = $7,140 per                    cycle.                   inspection cycle.
                             inspection cycle.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this proposed 
AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2017-0330; Directorate Identifier 
2017-NM-016-AD.

(a) Comments Due Date

    We must receive comments by June 15, 2017.

[[Page 20290]]

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 737-300, -400, -500 
airplanes, certificated in any category, as identified in Boeing 
Alert Service Bulletin 737-53A1365, dated January 23, 2017.

(d) Subject

    Air Transport Association (ATA) of America Code 53; Fuselage.

(e) Unsafe Condition

    This AD was prompted by an evaluation by the design approval 
holder indicating that the lower skin at the skin lap splice lower 
fastener row is subject to widespread fatigue damage. We are issuing 
this AD to detect and correct cracks in the lower skin, which, if 
not detected, could link up, resulting in reduced structural 
integrity of the airplane and consequent uncontrolled decompression 
of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Repetitive Inspections

    Except as provided by paragraph (i) of this AD, at the 
applicable time specified in paragraph 1.E., ``Compliance,'' of 
Boeing Alert Service Bulletin 737-53A1365, dated January 23, 2017: 
Do external eddy current inspections at stringer S-14 on the left 
and right sides of the airplane (S-14L and S-14R) for any crack in 
the skin lap splice at the lower fastener row, in accordance with 
the Accomplishment Instructions of Boeing Alert Service Bulletin 
737-53A1365, dated January 23, 2017. Repeat the inspections 
thereafter at the applicable times specified in paragraph 1.E., 
``Compliance,'' of Boeing Alert Service Bulletin 737-53A1365, dated 
January 23, 2017.

(h) Repair

    If any crack is found during any inspection required by 
paragraph (g) of this AD, repair before further flight using a 
method approved in accordance with the procedures specified in 
paragraph (j) of this AD. Although Boeing Alert Service Bulletin 
737-53A1365, dated January 23, 2017, specifies to contact Boeing for 
appropriate action and specifies that action as ``RC'' (Required for 
Compliance), this AD requires repair as specified in this paragraph.

(i) Exceptions to Service Information Specifications

    (1) Where Boeing Alert Service Bulletin 737-53A1365, dated 
January 23, 2017, specifies a compliance time ``after the original 
issue date of this service bulletin,'' this AD requires compliance 
within the specified compliance time after the effective date of 
this AD.
    (2) The Condition column of Table 1 and Table 2 of paragraph 
1.E., ``Compliance,'' of Boeing Alert Service Bulletin 737-53A1365, 
dated January 23, 2017, refers to total flight cycles ``at the 
original issue date of this service bulletin.'' This AD, however, 
applies to the airplanes with the specified total flight cycles as 
of the effective date of this AD.

(j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Los Angeles Aircraft Certification Office, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the manager of the ACO, send it to the attention of the 
person identified in paragraph (k)(1) of this AD. Information may be 
emailed to: 9-ANM-LAACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Los Angeles ACO, to make those findings. To be approved, 
the repair method, modification deviation, or alteration deviation 
must meet the certification basis of the airplane, and the approval 
must specifically refer to this AD.
    (4) Except as required by paragraph (h) of this AD: For service 
information that contains steps that are labeled as Required for 
Compliance (RC), the provisions of paragraphs (j)(4)(i) and 
(j)(4)(ii) of this AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. If a step or substep is labeled ``RC Exempt,'' then the 
RC requirement is removed from that step or substep. An AMOC is 
required for any deviations to RC steps, including substeps and 
identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(k) Related Information

    (1) For more information about this AD, contact James Guo, 
Aerospace Engineer, Airframe Branch, ANM-120L, FAA, Los Angeles ACO, 
3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 562-627-
5357; fax: 562-627-5210; email: james.guo@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; Internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on April 24, 2017.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2017-08708 Filed 4-28-17; 8:45 am]
 BILLING CODE 4910-13-P

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.