January 5, 2017 – Federal Register Recent Federal Regulation Documents

Results 101 - 126 of 126
Propiconazole; Extension of Tolerance for Emergency Exemptions
Document Number: 2016-31827
Type: Rule
Date: 2017-01-05
Agency: Environmental Protection Agency
This regulation extends a time-limited tolerance for combined residues of the fungicide propiconazole and its metabolites in or on avocado at 10 parts per million (ppm) for an additional 3-year period. This tolerance will expire and is revoked on December 31, 2019. This action is in response to EPA's granting of an emergency exemption under the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA) authorizing use of the pesticide on avocado trees. In addition, the Federal Food, Drug, and Cosmetic Act (FFDCA) requires EPA to establish a time-limited tolerance or exemption from the requirement for a tolerance for pesticide chemical residues in food that will result from the use of a pesticide under an emergency exemption granted by EPA under FIFRA.
Special Conditions: Cranfield Aerospace Limited, Cessna Aircraft Company Model 525; Tamarack Load Alleviation System and Cranfield Winglets-Interaction of Systems and Structures
Document Number: 2016-31819
Type: Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
These special conditions are issued for the Cessna Aircraft Company model 525 airplane. This airplane as modified by Cranfield Aerospace Limited will have a novel or unusual design feature associated with the installation of a Tamarack Active Technology Load Alleviation System and Cranfield Winglets. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Proposed Establishment, Modification and Revocation of Air Traffic Service (ATS) Routes; Western United States
Document Number: 2016-31818
Type: Proposed Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
This action proposes to modify three jet routes and four VHF Omnidirectional Range (VOR) Federal airways; remove two VOR Federal Airway routes, and establish four and modify four low altitude Area Navigation (RNAV) routes (T-routes) in the western United States. The FAA is proposing this action due to the scheduled decommissioning of the Manteca, CA, and Maxwell, CA, VOR facilities, which provide navigation guidance for portions of the affected routes. This action would enhance the safety and management of aircraft within these routes in the National Airspace System (NAS).
Airworthiness Directives; CFE Company Turbofan Engines
Document Number: 2016-31780
Type: Proposed Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain CFE Company (CFE) turbofan engines. This proposed AD was prompted by a quality escape for high-pressure compressor (HPC) impellers made from forgings with nonconforming material grain size. This proposed AD would require removal of the HPC impeller. We are proposing this AD to correct the unsafe condition on these products.
Department of Defense Personnel Security Program Regulation
Document Number: 2016-31756
Type: Rule
Date: 2017-01-05
Agency: Department of Defense, Office of the Secretary
This final rule removes DoD's regulation concerning personnel security. The codified rule is outdated and no longer accurate or applicable as written. The rule does not impose obligations on members of the public that are not already imposed by statute. It paraphrases and summarizes relevant sources of law and does not substantively deviate from them.
Air Plan Approval; Georgia: Procedures for Testing and Monitoring Sources of Air Pollutants
Document Number: 2016-31754
Type: Proposed Rule
Date: 2017-01-05
Agency: Environmental Protection Agency
The Environmental Protection Agency (EPA) is proposing to approve portions of State Implementation Plan (SIP) revisions submitted by the State of Georgia, through the Georgia Department of Natural Resources' Environmental Protection Division (GA EPD), on April 11, 2003, November 29, 2010, July 25, 2014, November 23, 2015, and November 29, 2016. The SIP submittals include changes to GA EPD's air quality rules that modify definitions. The portions of the SIP revisions that EPA is proposing to approve are consistent with the requirements of the Clean Air Act (CAA or Act).
Air Plan Approval; Georgia: Procedures for Testing and Monitoring Sources of Air Pollutants
Document Number: 2016-31753
Type: Rule
Date: 2017-01-05
Agency: Environmental Protection Agency
The Environmental Protection Agency (EPA) is taking direct final action to approve portions of State Implementation Plan (SIP) revisions submitted by the State of Georgia, through the Georgia Department of Natural Resources' Environmental Protection Division (GA EPD), on April 11, 2003, November 29, 2010, July 25, 2014, November 23, 2015, and November 29, 2016. The SIP submittals include changes to GA EPD's air quality rules that modify definitions. The portions of the SIP revisions that EPA is approving are consistent with the requirements of the Clean Air Act (CAA or Act).
Agency Information Collection Activities: Submission to OMB for Review and Approval; Public Comment Request; The National Health Service Corps Loan Repayment Program
Document Number: 2016-31723
Type: Notice
Date: 2017-01-05
Agency: Department of Health and Human Services, Health Resources and Services Administration
In compliance with Section 3507(a)(1)(D) of the Paperwork Reduction Act of 1995, HRSA has submitted an Information Collection Request (ICR) to the Office of Management and Budget (OMB) for review and approval. Comments submitted during the first public review of this ICR will be provided to OMB. OMB will accept further comments from the public during the review and approval period.
Requests for Approving Certain Alternative Methods for Computing Withdrawal Liability; Settlement of Withdrawal and Mass Withdrawal Liability
Document Number: 2016-31715
Type: Notice
Date: 2017-01-05
Agency: Pension Benefit Guaranty Corporation, Agencies and Commissions
This is a request for information (RFI) to inform PBGC on issues arising from arrangements between employers and multiemployer plans involving an alternative ``two-pool'' withdrawal liability method. PBGC seeks information from the general public and all interested stakeholders, including multiemployer plan participants and beneficiaries, organizations serving or representing retirees and other such individuals, multiemployer plan sponsors and professional advisors, contributing employers, unions, and other interested parties about these arrangements, including the various forms these arrangements may take, the terms and conditions that apply to new and existing contributing employers who enter into such arrangements, and the benefits and risks these arrangements may present to multiemployer plans and their participants, employers, the multiemployer pension insurance program, and other stakeholders in the multiemployer system.
Airworthiness Directives; B-N Group Ltd. Airplanes
Document Number: 2016-31699
Type: Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
We are superseding an airworthiness directive (AD) 2016-06-01 for B-N Group Ltd. Models BN-2, BN-2A, BN-2A-2, BN-2A-3, BN-2A-6, BN- 2A-8, BN-2A-9, BN-2A-20, BN-2A-21, BN-2A-26, BN-2A-27, BN-2B-20, BN-2B- 21, BN-2B-26, BN-2B-27, BN-2T-4R, BN-2T, BN2A MK. III, BN2A MK. III-2, and BN2A MK. III-3 (all models on Type Certificate Data Sheets A17EU and A29EU) airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracks in the inner shell of certain pitot/static pressure heads. This AD changes model applicability due to errors found in AD 2016-06-01. We are issuing this AD to require actions to address the unsafe condition on these products.
DoD Freedom of Information Act (FOIA) Program
Document Number: 2016-31686
Type: Rule
Date: 2017-01-05
Agency: Department of Defense, Office of the Secretary
This part revises the Department of Defense (DoD) Freedom of Information Act (FOIA) regulation to implement the FOIA and incorporate the provisions of the OPEN Government Act of 2007 and the FOIA Improvement Act of 2016. This part promotes uniformity in the Department of Defense (DoD) FOIA Program. It takes precedence over all DoD Component issuances that supplement and implement the DoD FOIA Program.
Steel Import Monitoring and Analysis System
Document Number: 2016-31667
Type: Rule
Date: 2017-01-05
Agency: Department of Commerce, International Trade Administration
The Department of Commerce (the Department) is extending the Steel Import Monitoring and Analysis (SIMA) system until March 21, 2022. The purpose of the SIMA system is to provide to the public statistical data on steel imports entering the United States roughly five weeks earlier than it would otherwise be available. Aggregate data collected from the steel import licenses are made available to the public on a weekly basis following review by the Department.
National Advisory Council for Environmental Policy and Technology: Assumable Waters Subcommittee; Notice of Public Meeting
Document Number: 2016-31642
Type: Notice
Date: 2017-01-05
Agency: Environmental Protection Agency
Consistent with the Federal Advisory Committee Act, the Environmental Protection Agency (EPA) is giving notice of an upcoming public meeting of the Assumable Waters Subcommittee convened under the National Advisory Council for Environmental Policy and Technology (NACEPT). The Assumable Waters Subcommittee will provide advice and recommendations as to how the EPA can best clarify assumable waters for dredge and fill permit programs pursuant to Clean Water Act section 404(g)(1). The EPA is undertaking this effort to support states and tribes that wish to assume the program. Similar to the parent NACEPT, the subcommittee represents a diversity of interests from academia, industry, non-governmental organizations, and local, State, and tribal governments. Meeting agendas and materials will be posted at www.epa.gov/cwa-404/assumable-waters-sub-committee.
Airworthiness Directives; Sikorsky Aircraft Corporation Helicopters (Type Certificate Previously Held by Schweizer Aircraft Corporation)
Document Number: 2016-31622
Type: Proposed Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
We propose to supersede airworthiness directive (AD) 93-17-13 for Schweizer Aircraft Corporation and Hughes Helicopters, Inc. (now Sikorsky Aircraft Corporation) (Sikorsky) Model TH55A, 269A, 269A-1, 269B, and 269C helicopters. AD 93-17-13 requires installing tachometer markings and inspecting the driveshaft. This proposed AD would require recurring inspections of the driveshaft and would expand the applicability to include Model 269C-1 helicopters. This proposed AD is prompted by reports of accidents because of driveshaft failures. The actions of this proposed AD are intended to prevent the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-31619
Type: Proposed Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for all The Boeing Company Model 757-200, -200PF, and -200CB series airplanes. This proposed AD was prompted by an evaluation by the design approval holder (DAH) indicating that certain fuselage circumferential splice plates are subject to widespread fatigue damage (WFD). This proposed AD would require repetitive low frequency eddy current (LFEC) inspections for cracks of certain circumferential splice plates, and repairs if necessary. We are proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; PILATUS AIRCRAFT LTD. Airplanes
Document Number: 2016-31600
Type: Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
We are superseding Airworthiness Directive (AD) 2014-22-01 for all PILATUS AIRCRAFT LTD. Models PC-12, PC-12/45, PC-12/47, and PC-12/ 47E airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a need to incorporate new revisions into the Limitations section, Chapter 4, of the FAA-approved maintenance program (e.g., maintenance manual). The limitations were revised to include repetitive inspections of the main landing gear (MLG) attachment bolts. We are issuing this AD to require actions to address the unsafe condition on these products.
Endangered and Threatened Wildlife and Plants; Removing Trichostema austromontanum
Document Number: 2016-31581
Type: Proposed Rule
Date: 2017-01-05
Agency: Fish and Wildlife Service, Department of the Interior
We, the U.S. Fish and Wildlife Service (Service), propose to remove the plant Trichostema austromontanum ssp. compactum (Hidden Lake bluecurls) from the Federal List of Endangered and Threatened Plants on the basis of recovery. This determination is based on a review of the best available scientific and commercial information, which indicates that the threats to T. a. ssp. compactum have been eliminated or reduced to the point where it no longer meets the definition of an endangered species or a threatened species under the Endangered Species Act of 1973, as amended (Act). We are seeking information and comments from the public regarding this proposed rule and the draft post- delisting monitoring (PDM) plan for T. a. ssp. compactum.
Revisions and Clarifications in Requirements for the Processing of Donated Foods
Document Number: 2016-31561
Type: Proposed Rule
Date: 2017-01-05
Agency: Department of Agriculture, Food and Nutrition Service
This rule proposes to revise and clarify requirements for the processing of donated foods in order to: Incorporate successful processing options tested in demonstration projects, ensure accountability for donated foods provided for processing, and increase program efficiency. The rule would require multi-State processors to enter into National Processing Agreements to process donated foods into end products, permit processors to substitute commercially purchased beef and pork of U.S. origin and of equal or better quality for donated beef and pork, and would increase oversight of inventories of donated foods at processors. The rule also revises regulatory provisions in plain language, to make them easier to read and understand.
Regulations Implementing FAST Act Section 61003-Critical Electric Infrastructure Security and Amending Critical Energy Infrastructure Information; Availability of Certain North American Electric Reliability Corporation Databases to the Commission; Correction
Document Number: 2016-31541
Type: Rule
Date: 2017-01-05
Agency: Department of Energy, Federal Energy Regulatory Commission
This document contains corrections to the final rule (RM16-15- 000, RM15-25-001) which published in the Federal Register on Wednesday, December 21, 2016 (81 FR 93732). The final rule amended the Commission's regulations to implement provisions of the Fixing America's Surface Transportation Act that pertain to the designation, protection and sharing of Critical Electric Infrastructure Information.
International Mailing Services: Mailing Services Price Changes
Document Number: 2016-31525
Type: Rule
Date: 2017-01-05
Agency: Postal Service, Agencies and Commissions
On October 17, 2016, the Postal Service published a notice of proposed price adjustments to reflect a notice of price adjustments filed with the Postal Regulatory Commission (PRC). The PRC has found that price adjustments contained in the Postal Service's notice may go into effect on January 22, 2017. The Postal Service will revise Notice 123, Price List to reflect the new prices.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2016-31367
Type: Proposed Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
We propose to supersede Airworthiness Directive (AD) 2014-12- 13, which applies to all The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. AD 2014-12-13 currently requires repetitive inspections for cracking of the main landing gear (MLG) beam, and the rear spar upper chord and rear spar web; and repair if necessary. Since we issued AD 2014-12-13, we received reports of additional cracking in the inspar upper skin, rear spar web and rear spar upper chord. This proposed AD would expand the inspection area and add related investigative and corrective actions if necessary. We are proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Defense and Space S.A. (Formerly Known as Construcciones Aeronauticas, S.A.) Airplanes
Document Number: 2016-31365
Type: Proposed Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for all Airbus Defense and Space S.A. Model CN-235, CN-235-100, CN-235-200, CN- 235-300, and C-295 airplanes. This proposed AD was prompted by reports of excessive play between bushings and their respective fitting housings at certain elevator fittings. This proposed AD would require a one-time detailed inspection and repetitive eddy current inspections of the elevator hinge fitting and bracket assembly, and corrective actions if necessary. We are proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Airplanes
Document Number: 2016-31239
Type: Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
We are superseding Airworthiness Directive (AD) 2014-26-08, for all Airbus Model A330-200, -200F, and -300 series airplanes. AD 2014-26-08 required revising the maintenance or inspection program to incorporate new maintenance requirements and airworthiness limitations. This new AD requires revising the maintenance or inspection program, as applicable, to incorporate new or revised airworthiness limitation requirements. This new AD also removes certain airplanes from the applicability. This AD was prompted by a determination that more restrictive maintenance instructions and airworthiness limitations are necessary. We are issuing this AD to address the unsafe condition on these products.
Eligibility and Standards for Peace Corps Volunteer Service
Document Number: 2016-30442
Type: Rule
Date: 2017-01-05
Agency: Peace Corps, Agencies and Commissions
The Peace Corps issues this final rule to restate and update the requirements for eligibility for Peace Corps Volunteer service, and the factors considered in the assessment and selection of eligible applicants for training and service. The requirements and factors for eligibility and selection were last published in 1984. A revision of the regulation is necessary to conform to changes in Federal laws and regulations, particularly with respect to those prohibiting discrimination on the basis of disability, and to reflect policy changes made by the Peace Corps.
Airworthiness Directives; Airbus Airplanes
Document Number: 2016-30411
Type: Rule
Date: 2017-01-05
Agency: Federal Aviation Administration, Department of Transportation
We are adopting a new airworthiness directive (AD) for all Airbus Model A330-200, -200 Freighter, and -300 series airplanes; and Model A340-200, -300, -500, and -600 series airplanes. This AD was prompted by certain anomalies of the flight guidance computers. We are issuing this AD to address the unsafe condition on these products.
Energy Conservation Program: Test Procedures for Central Air Conditioners and Heat Pumps
Document Number: 2016-30004
Type: Rule
Date: 2017-01-05
Agency: Department of Energy
On August 24, 2016, the U.S. Department of Energy (DOE) published a supplemental notice of proposed rulemaking (SNOPR) to amend the test procedure for central air conditioners and heat pumps. That SNOPR serves as the basis for this final rule. This final rule amends the test procedure and specific certification, compliance, and enforcement provisions related to this product. In this final rule, DOE makes two sets of amendments to the test procedure: Amendments to appendix M that would be required as the basis for making efficiency representations starting 180 days after final rule publication and a new appendix M1 that would be the basis for making efficiency representations as of the compliance date for any amended energy conservation standards. The new appendix M1 establishes new efficiency metrics SEER2, EER2, and HSPF2 that are based on the current efficiency metrics for cooling and heating performance, but generally have different numerical values than the current metrics. Broadly speaking, the amendments address off-mode test procedures, test set-up and fan delays, external static pressure conditions for testing, represented values for CAC/HP that are distributed in commerce with multiple refrigerants, the methodology for testing and calculating heating performance, and testing of variable-speed systems.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.