Airworthiness Directives; Dassault Aviation Airplanes, 26495-26497 [2016-10124]

Download as PDF Federal Register / Vol. 81, No. 85 / Tuesday, May 3, 2016 / Proposed Rules (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Modification Within 60 months after the effective date of this AD, modify the fuel quantity indicating system (FQIS) to prevent development of an ignition source inside the center fuel tank due to electrical fault conditions, using a method approved by the Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA. asabaliauskas on DSK9F6TC42PROD with PROPOSALS (h) Alternative Actions for Cargo Airplanes For airplanes used exclusively for cargo operations: As an alternative to the requirements of paragraph (g) of this AD, do the actions specified in paragraphs (h)(1) and (h)(2) of this AD. To exercise this alternative, operators must perform the first inspection required under paragraph (h)(1) of this AD within 6 months after the effective date of this AD. To exercise this alternative for airplanes returned to service after conversion of the airplane from a passenger configuration to an all-cargo configuration more than 6 months after the effective date of this AD, operators must perform the first inspection required under paragraph (h)(1) of this AD prior to further flight after the conversion. (1) Within 6 months after the effective date of this AD, record the existing fault codes stored in the fuel quantity indicating (FQI) computer, and then do a BITE check (check of built-in test equipment) of the FQI computer, using a method approved by the Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA. If any fault code is recorded prior to the BITE check or as a result of the BITE check, before further flight, do all applicable repairs and repeat the BITE check until a successful test is performed with no fault found, using a method approved by the Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA. Repeat these actions thereafter at intervals not to exceed 650 flight hours. Modification as specified in paragraph (h)(2) of this AD does not terminate the repetitive BITE check requirement of this paragraph. (2) Within 60 months after the effective date of this AD, modify the airplane by separating FQIS wiring that runs between the FQI computer and the center fuel tank wall penetrations, including any circuits that might pass through a main fuel tank, from other airplane wiring that is not intrinsically safe, using methods approved by the Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA. (i) Alternative Methods of Compliance (AMOCs) (1) The Manager, International Branch, ANM–116, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the VerDate Sep<11>2014 22:30 May 02, 2016 Jkt 238001 attention of the person identified in paragraph (j) of this AD. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. (j) Related Information For more information about this AD, contact Dan Rodina, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; telephone 425–227–2125; fax 425–227–1149. Issued in Renton, Washington, on April 15, 2016. Victor Wicklund, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2016–09792 Filed 5–2–16; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2016–6146; Directorate Identifier 2014–NM–120–AD] RIN 2120–AA64 Airworthiness Directives; Dassault Aviation Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to supersede Airworthiness Directive (AD) 2008–19– 08, for all Dassault Aviation Model Falcon 10 airplanes. AD 2008–19–08 currently requires repetitive replacement of the flexible hoses installed in the wing (slat) anti-icing system with new hoses. Since we issued AD 2008–19–08, additional reports were received of collapse of the flexible hoses installed in the slat anti-icing systems on airplanes equipped with new, improved hoses. This proposed AD would require reducing the life limit of these flexible hoses, which would reduce the repetitive replacement intervals. We are proposing this AD to prevent collapse of the flexible hoses in the slat anti-icing system, which could lead to insufficient anti-icing capability and, if icing is encountered in this situation, could result in reduced controllability of the airplane. DATES: We must receive comments on this proposed AD by June 17, 2016. ADDRESSES: You may send comments by any of the following methods: SUMMARY: PO 00000 Frm 00011 Fmt 4702 Sfmt 4702 26495 • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2016– 6146; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, International Branch, ANM–116, FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA 98057– 3356; telephone 425–227–1137; fax 425–227–1149. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2016–6146; Directorate Identifier 2014–NM–120–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion On September 12, 2008, we issued AD 2008–19–08, Amendment 39–15675 (73 E:\FR\FM\03MYP1.SGM 03MYP1 26496 Federal Register / Vol. 81, No. 85 / Tuesday, May 3, 2016 / Proposed Rules FR 54492, September 22, 2008) (‘‘AD 2008–19–08’’). AD 2008–19–08 requires actions intended to address an unsafe condition on all Dassault Aviation Model Falcon 10 airplanes. Since we issued AD 2008–19–08, additional reports were received of collapse of the flexible hoses installed in the slat anti-icing systems on airplanes equipped with new, improved hoses. The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Union, has issued EASA Airworthiness Directive 2014–0104, dated May 7, 2014 (referred to after this as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition on all Dassault Aviation Model Falcon 10 airplanes. The MCAI states: Occurrences were reported involving an inservice Falcon 10 aeroplane, where wing anti-ice hoses collapsed. The subsequent investigation revealed that the flexible hose, Part Number (P/N) FAL1005, collapsed because of an internal ply separation. This condition, if not corrected, could lead to failure of the ice-protection system to remove ice accretion on the wing, possibly resulting in reduced control of the aeroplane. To address this potential unsafe condition, EASA issued AD 2005–0020 and AD 2006– 0114 [which corresponds to AD 2008–19–08], respectively, imposing flight limitations and requiring replacement of the flexible hoses P/N FAL1005 with improved hoses P/N FAL1007. Since those [EASA] ADs were issued, further occurrences were reported concerning aeroplanes with improved hoses, which led to the conclusion that the life limit of the flexible hose P/N FAL1007 must be reduced. For the reasons above, this [EASA] AD retains the requirements of EASA AD 2006– 0114, which is superseded; supersedes EASA AD 2005–0020; requires replacement of flexible hoses having P/N FAL 1000, P/N 1001, P/N FAL1005, or P/N FAL1005D, and reduces the life limit of the flexible hoses P/N 1007 [which would reduce the repetitive replacement intervals]. asabaliauskas on DSK9F6TC42PROD with PROPOSALS You may examine the MCAI in the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2016– 6146. FAA’s Determination and Requirements of This Proposed AD This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI. We are proposing this AD because we evaluated all pertinent information and determined an unsafe VerDate Sep<11>2014 22:30 May 02, 2016 Jkt 238001 condition exists and is likely to exist or develop on other products of the same type design. Costs of Compliance We estimate that this proposed AD affects 124 airplanes of U.S. registry. The actions that are required by AD 2008–19–08 and retained in this proposed AD take about 8 work-hours per product, at an average labor rate of $85 per work-hour. Required parts cost about $880. Based on these figures, the estimated cost of the actions that are required by AD 2008–19–08 is up to $1,560, per replacement cycle. We also estimate that it would take about 4 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Required parts would cost about $936 per product. Based on these figures, we estimate the cost of this proposed AD on U.S. operators to be $158,224, or $1,276 per product. 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); 3. Will not affect intrastate aviation in Alaska; and 4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; PO 00000 Frm 00012 Fmt 4702 Sfmt 4702 § 39.13 [Amended] 2. The FAA amends § 39.13 by removing Airworthiness Directive (AD) 2008–19–08, Amendment 39–15675 (73 FR 54492, September 22, 2008), and adding the following new AD: ■ Dassault Aviation: Docket No. FAA–2016– 6146; Directorate Identifier 2014–NM– 120–AD. (a) Comments Due Date We must receive comments by June 17, 2016. (b) Affected ADs This AD replaces AD 2008–19–08, Amendment 39–15675 (73 FR 54492, September 22, 2008) (‘‘AD 2008–19–08’’). (c) Applicability This AD applies to all Dassault Aviation Model Falcon 10 airplanes, certificated in any category. (d) Subject Air Transport Association (ATA) of America Code 30, Ice and Rain Protection. (e) Reason This AD was prompted by reports of collapse of the flexible hoses installed in the slat anti-icing systems on airplanes equipped with new, improved hoses. We are issuing this AD to prevent collapse of the flexible hoses in the slat anti-icing system, which could lead to insufficient anti-icing capability and, if icing is encountered in this situation, could result in reduced controllability of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. E:\FR\FM\03MYP1.SGM 03MYP1 Federal Register / Vol. 81, No. 85 / Tuesday, May 3, 2016 / Proposed Rules (g) Retained Repetitive Hose Replacement With Revised Compliance Language This paragraph restates the requirements of paragraph (h) of AD 2008–19–08, with revised compliance language. As of October 27, 2008 (the effective date of AD 2008–19– 08), replace the flexible hoses installed in the slat anti-icing system with new hoses having part number (P/N) FAL1007, in accordance with the Accomplishment Instructions of Dassault Service Bulletin F10–313, Revision 1, dated May 10, 2006, within 700 flight hours since the last replacement or within 100 flight hours after October 27, 2008, whichever occurs later, and thereafter at intervals not to exceed 700 flight hours. Accomplishing the replacement required by paragraph (h) of this AD ends the repetitive inspections required by this paragraph. (h) New Requirement of This AD: Hose Replacement for Certain Part Numbers Within 65 days after the effective date of this AD: Replace any flexible hose having part number (P/N) FAL1000, P/N FAL1001, or P/N FAL1005D with a new, improved flexible hose having P/N FAL1007, using a method approved by the Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA; or the European Aviation Safety Agency (EASA); or Dassault Aviation’s EASA Design Organization Approval (DOA). asabaliauskas on DSK9F6TC42PROD with PROPOSALS (i) Life-limit for P/N FAL1007—Repetitive Replacements At the later of the times specified in paragraphs (i)(1) and (i)(2) of this AD, replace any flexible hose having part number P/N FAL1007 with a serviceable flexible hose having P/N FAL1007, using a method approved by the Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA; or EASA; or Dassault Aviation’s EASA DOA. Thereafter, before the accumulation of 350 flight hours on any flexible hose having P/N FAL1007, replace the flexible hose with a serviceable flexible hose having P/N FAL1007. (1) Before the accumulation of 350 flight hours on the flexible hose P/N FAL1007 since first installation on an airplane. (2) At the earlier of the times specified in (i)(2)(i) and (i)(2)(ii) of this AD. (i) Within 200 flight hours after the effective date of this AD. (ii) Before the accumulation of 700 flight hours on the flexible hose P/N FAL1007 since first installation on an airplane, or within 65 days after the effective date of this AD, whichever occurs later. (j) Definition of Serviceable Flexible Hose For the purpose of this AD, a serviceable flexible hose is a flexible hose having P/N FAL1007 that has accumulated 350 flight hours or less since first installation on an airplane. 22:30 May 02, 2016 Jkt 238001 (l) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; telephone 425–227–1137; fax 425–227–1149. Information may be emailed to: 9-ANM-116AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The AMOC approval letter must specifically reference this AD. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Branch, ANM– 116, Transport Airplane Directorate, FAA; or the EASA; or Dassault Aviation’s EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature. (m) Related Information Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA Airworthiness Directive 2014–0104, dated May 7, 2014, for related information. This MCAI may be found in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA– 2016–6146. Issued in Renton, Washington, on April 20, 2016. John P. Piccola, Jr., Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2016–10124 Filed 5–2–16; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 71 [Docket No. FAA–2016–4271; Airspace Docket No. 16–AGL–6] (k) Parts Installation Limitation After accomplishing the replacement required by paragraph (h) of this AD, no person may install a flexible hose in the slat anti-icing system on any airplane, unless that hose is a serviceable flexible hose having P/N FAL1007, and thereafter repetitive hose VerDate Sep<11>2014 replacements are done as required by paragraph (i) of this AD. Proposed Amendment of Class E Airspace for the Following Minnesota Towns; Hutchinson, MN; Jackson, MN; Pipestone, MN; Two Harbors, MN; and Waseca, MN Federal Aviation Administration (FAA), DOT. AGENCY: PO 00000 Frm 00013 Fmt 4702 Sfmt 4702 26497 Notice of proposed rulemaking (NPRM). ACTION: This action proposes to modify Class E airspace extending upward from 700 feet above the surface at Hutchinson Municipal Airport-Butler Field, Hutchinson, MN; Jackson Municipal Airport, Jackson, MN; Pipestone Municipal Airport, Pipestone, MN; Richard B. Helgeson Airport, Two Harbors, MN; and Waseca Municipal Airport, Waseca, MN. Decommissioning of the non-directional radio beacon (NDB), cancellation of NDB approaches, and implementation of area navigation (RNAV) procedures have made this action necessary for the safety and management of Instrument Flight Rules (IFR) operations at the above airports. This action would also update the geographic coordinates at Hutchinson Municipal-Butler Field, Jackson Municipal Airport, Pipestone Municipal Airport, and Richard B. Helgeson Airport, to coincide with the FAAs aeronautical database. DATES: Comments must be received on or before June 17, 2016. ADDRESSES: Send comments on this proposal to the U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590; telephone (202) 366–9826. You must identify FAA Docket No. FAA–2016–4271; Airspace Docket No. 16–AGL–6, at the beginning of your comments. You may also submit comments through the Internet at https://www.regulations.gov. You may review the public docket containing the proposal, any comments received, and any final disposition in person in the Dockets Office between 9:00 a.m. and 5:00 p.m., Monday through Friday, except Federal holidays. The Docket Office (telephone 1–800–647–5527) is on the ground floor of the building at the above address. FAA Order 7400.9Z, Airspace Designations and Reporting Points, and subsequent amendments can be viewed online at https://www.faa.gov/air_traffic/ publications/. For further information, you can contact the Airspace Policy Group, Federal Aviation Administration, 800 Independence Avenue SW., Washington, DC 20591; telephone: 202–267–8783. The Order is also available for inspection at the National Archives and Records Administration (NARA). For information on the availability of FAA Order 7400.9Z at NARA, call 202–741– 6030, or go to https://www.archives.gov/ federal_register/code_of_federalregulations/ibr_locations.html. SUMMARY: E:\FR\FM\03MYP1.SGM 03MYP1

Agencies

[Federal Register Volume 81, Number 85 (Tuesday, May 3, 2016)]
[Proposed Rules]
[Pages 26495-26497]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-10124]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2016-6146; Directorate Identifier 2014-NM-120-AD]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to supersede Airworthiness Directive (AD) 2008-19-
08, for all Dassault Aviation Model Falcon 10 airplanes. AD 2008-19-08 
currently requires repetitive replacement of the flexible hoses 
installed in the wing (slat) anti-icing system with new hoses. Since we 
issued AD 2008-19-08, additional reports were received of collapse of 
the flexible hoses installed in the slat anti-icing systems on 
airplanes equipped with new, improved hoses. This proposed AD would 
require reducing the life limit of these flexible hoses, which would 
reduce the repetitive replacement intervals. We are proposing this AD 
to prevent collapse of the flexible hoses in the slat anti-icing 
system, which could lead to insufficient anti-icing capability and, if 
icing is encountered in this situation, could result in reduced 
controllability of the airplane.

DATES: We must receive comments on this proposed AD by June 17, 2016.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2016-
6146; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1137; 
fax 425-227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2016-6146; 
Directorate Identifier 2014-NM-120-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    On September 12, 2008, we issued AD 2008-19-08, Amendment 39-15675 
(73

[[Page 26496]]

FR 54492, September 22, 2008) (``AD 2008-19-08''). AD 2008-19-08 
requires actions intended to address an unsafe condition on all 
Dassault Aviation Model Falcon 10 airplanes.
    Since we issued AD 2008-19-08, additional reports were received of 
collapse of the flexible hoses installed in the slat anti-icing systems 
on airplanes equipped with new, improved hoses.
    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Union, has issued EASA 
Airworthiness Directive 2014-0104, dated May 7, 2014 (referred to after 
this as the Mandatory Continuing Airworthiness Information, or ``the 
MCAI''), to correct an unsafe condition on all Dassault Aviation Model 
Falcon 10 airplanes. The MCAI states:

    Occurrences were reported involving an in-service Falcon 10 
aeroplane, where wing anti-ice hoses collapsed. The subsequent 
investigation revealed that the flexible hose, Part Number (P/N) 
FAL1005, collapsed because of an internal ply separation.
    This condition, if not corrected, could lead to failure of the 
ice-protection system to remove ice accretion on the wing, possibly 
resulting in reduced control of the aeroplane.
    To address this potential unsafe condition, EASA issued AD 2005-
0020 and AD 2006-0114 [which corresponds to AD 2008-19-08], 
respectively, imposing flight limitations and requiring replacement 
of the flexible hoses P/N FAL1005 with improved hoses P/N FAL1007.
    Since those [EASA] ADs were issued, further occurrences were 
reported concerning aeroplanes with improved hoses, which led to the 
conclusion that the life limit of the flexible hose P/N FAL1007 must 
be reduced.
    For the reasons above, this [EASA] AD retains the requirements 
of EASA AD 2006-0114, which is superseded; supersedes EASA AD 2005-
0020; requires replacement of flexible hoses having P/N FAL 1000, P/
N 1001, P/N FAL1005, or P/N FAL1005D, and reduces the life limit of 
the flexible hoses P/N 1007 [which would reduce the repetitive 
replacement intervals].

You may examine the MCAI in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2016-
6146.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI. We are 
proposing this AD because we evaluated all pertinent information and 
determined an unsafe condition exists and is likely to exist or develop 
on other products of the same type design.

Costs of Compliance

    We estimate that this proposed AD affects 124 airplanes of U.S. 
registry.
    The actions that are required by AD 2008-19-08 and retained in this 
proposed AD take about 8 work-hours per product, at an average labor 
rate of $85 per work-hour. Required parts cost about $880. Based on 
these figures, the estimated cost of the actions that are required by 
AD 2008-19-08 is up to $1,560, per replacement cycle.
    We also estimate that it would take about 4 work-hours per product 
to comply with the basic requirements of this proposed AD. The average 
labor rate is $85 per work-hour. Required parts would cost about $936 
per product. Based on these figures, we estimate the cost of this 
proposed AD on U.S. operators to be $158,224, or $1,276 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2008-19-08, Amendment 39-15675 (73 FR 54492, September 22, 2008), and 
adding the following new AD:

Dassault Aviation: Docket No. FAA-2016-6146; Directorate Identifier 
2014-NM-120-AD.

(a) Comments Due Date

    We must receive comments by June 17, 2016.

(b) Affected ADs

    This AD replaces AD 2008-19-08, Amendment 39-15675 (73 FR 54492, 
September 22, 2008) (``AD 2008-19-08'').

(c) Applicability

    This AD applies to all Dassault Aviation Model Falcon 10 
airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 30, Ice and Rain 
Protection.

(e) Reason

    This AD was prompted by reports of collapse of the flexible 
hoses installed in the slat anti-icing systems on airplanes equipped 
with new, improved hoses. We are issuing this AD to prevent collapse 
of the flexible hoses in the slat anti-icing system, which could 
lead to insufficient anti-icing capability and, if icing is 
encountered in this situation, could result in reduced 
controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

[[Page 26497]]

(g) Retained Repetitive Hose Replacement With Revised Compliance 
Language

    This paragraph restates the requirements of paragraph (h) of AD 
2008-19-08, with revised compliance language. As of October 27, 2008 
(the effective date of AD 2008-19-08), replace the flexible hoses 
installed in the slat anti-icing system with new hoses having part 
number (P/N) FAL1007, in accordance with the Accomplishment 
Instructions of Dassault Service Bulletin F10-313, Revision 1, dated 
May 10, 2006, within 700 flight hours since the last replacement or 
within 100 flight hours after October 27, 2008, whichever occurs 
later, and thereafter at intervals not to exceed 700 flight hours. 
Accomplishing the replacement required by paragraph (h) of this AD 
ends the repetitive inspections required by this paragraph.

(h) New Requirement of This AD: Hose Replacement for Certain Part 
Numbers

    Within 65 days after the effective date of this AD: Replace any 
flexible hose having part number (P/N) FAL1000, P/N FAL1001, or P/N 
FAL1005D with a new, improved flexible hose having P/N FAL1007, 
using a method approved by the Manager, International Branch, ANM-
116, Transport Airplane Directorate, FAA; or the European Aviation 
Safety Agency (EASA); or Dassault Aviation's EASA Design 
Organization Approval (DOA).

(i) Life-limit for P/N FAL1007--Repetitive Replacements

    At the later of the times specified in paragraphs (i)(1) and 
(i)(2) of this AD, replace any flexible hose having part number P/N 
FAL1007 with a serviceable flexible hose having P/N FAL1007, using a 
method approved by the Manager, International Branch, ANM-116, 
Transport Airplane Directorate, FAA; or EASA; or Dassault Aviation's 
EASA DOA. Thereafter, before the accumulation of 350 flight hours on 
any flexible hose having P/N FAL1007, replace the flexible hose with 
a serviceable flexible hose having P/N FAL1007.
    (1) Before the accumulation of 350 flight hours on the flexible 
hose P/N FAL1007 since first installation on an airplane.
    (2) At the earlier of the times specified in (i)(2)(i) and 
(i)(2)(ii) of this AD.
    (i) Within 200 flight hours after the effective date of this AD.
    (ii) Before the accumulation of 700 flight hours on the flexible 
hose P/N FAL1007 since first installation on an airplane, or within 
65 days after the effective date of this AD, whichever occurs later.

(j) Definition of Serviceable Flexible Hose

    For the purpose of this AD, a serviceable flexible hose is a 
flexible hose having P/N FAL1007 that has accumulated 350 flight 
hours or less since first installation on an airplane.

(k) Parts Installation Limitation

    After accomplishing the replacement required by paragraph (h) of 
this AD, no person may install a flexible hose in the slat anti-
icing system on any airplane, unless that hose is a serviceable 
flexible hose having P/N FAL1007, and thereafter repetitive hose 
replacements are done as required by paragraph (i) of this AD.

(l) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to ATTN: Tom 
Rodriguez, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, 
WA 98057-3356; telephone 425-227-1137; fax 425-227-1149. Information 
may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office. The 
AMOC approval letter must specifically reference this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, International 
Branch, ANM-116, Transport Airplane Directorate, FAA; or the EASA; 
or Dassault Aviation's EASA DOA. If approved by the DOA, the 
approval must include the DOA-authorized signature.

(m) Related Information

    Refer to Mandatory Continuing Airworthiness Information (MCAI) 
EASA Airworthiness Directive 2014-0104, dated May 7, 2014, for 
related information. This MCAI may be found in the AD docket on the 
Internet at https://www.regulations.gov by searching for and locating 
Docket No. FAA-2016-6146.


    Issued in Renton, Washington, on April 20, 2016.
John P. Piccola, Jr.,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2016-10124 Filed 5-2-16; 8:45 am]
 BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.