Airworthiness Directives; Technify Motors GmbH Reciprocating Engines, 19024-19025 [2016-07376]

Download as PDF 19024 Federal Register / Vol. 81, No. 64 / Monday, April 4, 2016 / Rules and Regulations (2) Strip coating, inspect, and recoat the teeth of the rotating CDP seal, P/N 1669M73P02. Use paragraph 3.C.(2) of GE Service Bulletin (SB) CF6–80E1 S/B 72–0529, Revision 01, dated August 21, 2015 to do the strip coating, inspecting, and recoating, as follows: (i) For engines that have had stationary CDP seal, P/N 1347M28G02, replaced or stationary CDP seal honeycomb repaired; strip coating, inspect, and recoat the teeth of the rotating CDP seal at the next engine shop visit. (ii) For engines that have not had stationary CDP seal, P/N 1347M28G02, replaced or stationary CDP seal honeycomb repaired; strip coating, inspect, and recoat the teeth of the rotating CDP seal at the next part exposure of the rotating CDP seal. (f) Installation Prohibition After the effective date of this AD, do not install any rotating CDP seal, P/N 1669M73P02, that has not had its seal teeth recoated using procedures specified in ESM 72–31–10, REPAIR 002 of GE CF6–80E1 (GEK99376) Engine Manual, Revision 42, dated March 15, 2014, into any engine. (g) Definitions (1) For the purpose of this AD, exposure of the rotating CDP seal is defined as removal of the compressor rear frame from the highpressure compressor (HPC) module. (2) For the purpose of this AD, an engine shop visit is defined as the induction of an engine into the shop for maintenance involving the separation of any major mating engine flanges, except that the separation of engine flanges solely for the following purposes is not considered a shop visit: (i) Transportation without subsequent engine maintenance. (ii) Removing the turbine rear frame (TRF) for repair of TRF cracking. (iii) Removing the top or bottom HPC case, or both, for HPC airfoil maintenance. (iv) Removing only the accessory gearbox and/or transfer gearbox. (v) Replacing the high-pressure turbine (HPT) stage 1 blades per CF6–80E1 SB 72– 0504 ‘‘Quick-Turn Workscope Procedure to Replace CF6–80E1 Stage 1 HPT Blades’’. (3) For the purpose of this AD, a stationary CDP seal is replaced if at any previous shop visit, the seal has been removed and a different seal is installed. mstockstill on DSK4VPTVN1PROD with RULES You may take credit for the actions that are required by paragraph (e) of this AD if the actions were performed before the effective date of this AD using the procedures in ESM 72–31–10, REPAIR 002 of the GE CF6–80E1 (GEK99376) Engine Manual, Revision 42, dated March 15, 2014, or earlier versions. Issued in Burlington, Massachusetts, on March 16, 2016. Ann C. Mollica, Acting Manager, Engine & Propeller Directorate, Aircraft Certification Service. [FR Doc. 2016–07377 Filed 4–1–16; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2015–5193; Directorate Identifier 2015–NE–35–AD; Amendment 39– 18464; AD 2016–07–19] The Manager, Engine Certification Office, FAA, may approve AMOCs to this AD. Use the procedures found in 14 CFR 39.19 to make your request. You may email your request to: ANE-AD-AMOC@faa.gov. Jkt 238001 Airworthiness Directives; Technify Motors GmbH Reciprocating Engines Federal Aviation Administration (FAA), DOT. ACTION: Final rule. AGENCY: We are adopting a new airworthiness directive (AD) for certain Technify Motors GmbH (type certificate previously held by Thielert Aircraft Engines GmbH) TAE 125–02–99 and TAE 125–02–114 reciprocating engines. This AD requires removal of affected SUMMARY: (i) Alternative Methods of Compliance (AMOCs) 17:02 Apr 01, 2016 (k) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) General Electric Company Service Bulletin CF6–80E1 S/B 72–0529, Revision 01, dated August 21, 2015. (ii) Reserved. (3) For GE service information identified in this AD, contact General Electric Company, GE Aviation, Room 285, 1 Neumann Way, Cincinnati, OH 45215; phone: 513–552–3272; email: aviation.fleetsupport@ge.com. (4) You may view this service information at FAA, Engine & Propeller Directorate, 1200 District Avenue, Burlington, MA. For information on the availability of this material at the FAA, call 781–238–7125. (5) You may view this service information at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https:// www.archives.gov/federal-register/cfr/ibrlocations.html. RIN 2120–AA64 (h) Credit for Previous Action VerDate Sep<11>2014 (j) Related Information (1) For more information about this AD, contact Herman Mak, Aerospace Engineer, Engine Certification Office, FAA, Engine & Propeller Directorate, 1200 District Avenue, Burlington, MA 01803; phone: 781–238– 7147; fax: 781–238–7199; email: herman.mak@faa.gov. PO 00000 Frm 00004 Fmt 4700 Sfmt 4700 fuel feed pumps. This AD was prompted by reports of in-flight shutdowns on TAE 125–02 engines. We are issuing this AD to prevent failure of the fuel feed pump, damage to the engine, and damage to the airplane. DATES: This AD becomes effective May 9, 2016. ADDRESSES: For service information identified in this AD, contact Technify Motors GmbH, Platanenstrasse 14, D– 09356 Sankt Egidien, Germany; phone: +49–37204–696–0; fax: +49–37204– 696–2912; email: support@ continentaldiesel.de. You may view this service information at the FAA, Engine & Propeller Directorate, 1200 District Avenue, Burlington, MA. For information on the availability of this material at the FAA, call 781–238–7125. It is also available on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2015– 5193. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2015– 5193; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the mandatory continuing airworthiness information (MCAI), the regulatory evaluation, any comments received, and other information. The address for the Docket Office (phone: 800–647–5527) is Document Management Facility, U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Philip Haberlen, Aerospace Engineer, Engine Certification Office, FAA, Engine & Propeller Directorate, 1200 District Avenue, Burlington, MA 01803; phone: 781–238–7770; fax: 781–238–7199; email: philip.haberlen@faa.gov. SUPPLEMENTARY INFORMATION: Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to the specified products. The NPRM was published in the Federal Register on January 4, 2016 (81 FR 27). The NPRM proposed to correct an unsafe condition for the specified products. The MCAI states: In-flight shut down occurrences have been reported on aeroplanes equipped with TAE 125–02 engines. The initial results of the E:\FR\FM\04APR1.SGM 04APR1 Federal Register / Vol. 81, No. 64 / Monday, April 4, 2016 / Rules and Regulations Regulatory Findings investigations showed that a defective fuel feed pump was the probable cause of the engine failure. You may obtain further information by examining the MCAI in the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2015– 5193. Comments We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM (81 FR 27, January 4, 2016). Conclusion We reviewed the available data and determined that air safety and the public interest require adopting this AD as proposed. Related Service Information Technify Motors GmbH has issued Operation & Maintenance Manual, CD– 135/CD–155, OM–02–02, Issue 4, Revision No. 5, dated September 18, 2015. The service information describes procedures for removing and replacing the fuel feed pump. Costs of Compliance We estimate that this AD affects 190 engines installed on airplanes of U.S. registry. We also estimate that it will take about 0.5 hours per engine to comply with this AD. The average labor rate is $85 per hour. Pro-rated cost of the life limit reduction is about $160 per part. Based on these figures, we estimate the cost of this AD on U.S. operators to be $38,475. mstockstill on DSK4VPTVN1PROD with RULES Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. VerDate Sep<11>2014 17:02 Apr 01, 2016 Jkt 238001 19025 (d) Reason We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), (3) Will not affect intrastate aviation in Alaska to the extent that it justifies making a regulatory distinction, and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. This AD was prompted by reports of inflight shutdowns on TAE 125–02 engines. We are issuing this AD to prevent failure of the fuel feed pump, damage to the engine, and damage to the airplane. List of Subjects in 14 CFR Part 39 (g) Related Information Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ 2016–07–19 Technify Motors GmbH (Type Certificate previously held by Thielert Aircraft Engines GmbH): Amendment 39–18464; Docket No. FAA–2015–5193; Directorate Identifier 2015–NE–35–AD. (a) Effective Date This AD becomes effective May 9, 2016. (b) Affected ADs None. (c) Applicability This AD applies to all Technify Motors GmbH TAE 125–02–99 and TAE 125–02–114 reciprocating engines with a fuel feed pump, part number (P/N) 05–7312–K0073xx, or P/ N 05–7312–K0133xx, where ‘‘xx’’ can be any number, installed. PO 00000 Frm 00005 Fmt 4700 Sfmt 9990 (e) Actions and Compliance Comply with this AD within the compliance times specified, unless already done. Remove from service each affected fuel feed pump before it exceeds 600 operating hours (OH) time in service (TIS) or within 110 OH after the effective date of this AD, whichever occurs later. (f) Installation Prohibition After the effective date of this AD, do not install onto any engine, any fuel feed pump, P/N 05–7312–K0073xx or P/N 05–7312– K0133xx, where ‘‘xx’’ can be any number, if the fuel feed pump has 600 hours or more TIS. If TIS of a fuel feed pump is unknown or has exceeded 600 hours TIS, then the fuel feed pump is not eligible for installation. Rebuilt, overhauled, or repaired fuel feed pumps or fuel feed pumps that lack a serial number, are not eligible for installation. (1) For more information about this AD, Philip Haberlen, Aerospace Engineer, Engine Certification Office, FAA, Engine & Propeller Directorate, 1200 District Avenue, Burlington, MA 01803; phone: 781–238– 7770; fax: 781–238–7199; email: philip.haberlen@faa.gov. (2) Refer to MCAI European Aviation Safety Agency AD 2015–0189, dated September 21, 2015, for more information. You may examine the MCAI in the AD docket on the Internet at https:// www.regulations.gov by searching for and locating it in Docket No. FAA–2015–5193. (3) For service information identified in this AD, contact Technify Motors GmbH, Platanenstrasse 14, D–09356 Sankt Egidien, Germany; phone: +49–37204–696–0; fax: +49–37204–696–2912; email: support@ continentaldiesel.de. (4) You may view this service information at the FAA, Engine & Propeller Directorate, 1200 District Avenue, Burlington, MA. For information on the availability of this material at the FAA, call 781–238–7125. (h) Material Incorporated by Reference None. Issued in Burlington, Massachusetts, on March 25, 2016. Colleen M. D’Alessandro, Manager, Engine & Propeller Directorate, Aircraft Certification Service. [FR Doc. 2016–07376 Filed 4–1–16; 8:45 am] BILLING CODE 4910–13–P E:\FR\FM\04APR1.SGM 04APR1

Agencies

[Federal Register Volume 81, Number 64 (Monday, April 4, 2016)]
[Rules and Regulations]
[Pages 19024-19025]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-07376]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2015-5193; Directorate Identifier 2015-NE-35-AD; 
Amendment 39-18464; AD 2016-07-19]
RIN 2120-AA64


Airworthiness Directives; Technify Motors GmbH Reciprocating 
Engines

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Technify Motors GmbH (type certificate previously held by Thielert 
Aircraft Engines GmbH) TAE 125-02-99 and TAE 125-02-114 reciprocating 
engines. This AD requires removal of affected fuel feed pumps. This AD 
was prompted by reports of in-flight shutdowns on TAE 125-02 engines. 
We are issuing this AD to prevent failure of the fuel feed pump, damage 
to the engine, and damage to the airplane.

DATES: This AD becomes effective May 9, 2016.

ADDRESSES: For service information identified in this AD, contact 
Technify Motors GmbH, Platanenstrasse 14, D-09356 Sankt Egidien, 
Germany; phone: +49-37204-696-0; fax: +49-37204-696-2912; email: 
support@continentaldiesel.de. You may view this service information at 
the FAA, Engine & Propeller Directorate, 1200 District Avenue, 
Burlington, MA. For information on the availability of this material at 
the FAA, call 781-238-7125. It is also available on the Internet at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2015-5193.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2015-
5193; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this AD, the mandatory continuing airworthiness information 
(MCAI), the regulatory evaluation, any comments received, and other 
information. The address for the Docket Office (phone: 800-647-5527) is 
Document Management Facility, U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Philip Haberlen, Aerospace Engineer, 
Engine Certification Office, FAA, Engine & Propeller Directorate, 1200 
District Avenue, Burlington, MA 01803; phone: 781-238-7770; fax: 781-
238-7199; email: philip.haberlen@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to the specified products. The 
NPRM was published in the Federal Register on January 4, 2016 (81 FR 
27). The NPRM proposed to correct an unsafe condition for the specified 
products. The MCAI states:

In-flight shut down occurrences have been reported on aeroplanes 
equipped with TAE 125-02 engines. The initial results of the

[[Page 19025]]

investigations showed that a defective fuel feed pump was the 
probable cause of the engine failure.

    You may obtain further information by examining the MCAI in the AD 
docket on the Internet at https://www.regulations.gov by searching for 
and locating Docket No. FAA-2015-5193.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM (81 FR 27, January 4, 
2016).

Conclusion

    We reviewed the available data and determined that air safety and 
the public interest require adopting this AD as proposed.

Related Service Information

    Technify Motors GmbH has issued Operation & Maintenance Manual, CD-
135/CD-155, OM-02-02, Issue 4, Revision No. 5, dated September 18, 
2015. The service information describes procedures for removing and 
replacing the fuel feed pump.

Costs of Compliance

    We estimate that this AD affects 190 engines installed on airplanes 
of U.S. registry. We also estimate that it will take about 0.5 hours 
per engine to comply with this AD. The average labor rate is $85 per 
hour. Pro-rated cost of the life limit reduction is about $160 per 
part. Based on these figures, we estimate the cost of this AD on U.S. 
operators to be $38,475.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska to the extent 
that it justifies making a regulatory distinction, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2016-07-19 Technify Motors GmbH (Type Certificate previously held by 
Thielert Aircraft Engines GmbH): Amendment 39-18464; Docket No. FAA-
2015-5193; Directorate Identifier 2015-NE-35-AD.

(a) Effective Date

    This AD becomes effective May 9, 2016.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Technify Motors GmbH TAE 125-02-99 and 
TAE 125-02-114 reciprocating engines with a fuel feed pump, part 
number (P/N) 05-7312-K0073xx, or P/N 05-7312-K0133xx, where ``xx'' 
can be any number, installed.

(d) Reason

    This AD was prompted by reports of in-flight shutdowns on TAE 
125-02 engines. We are issuing this AD to prevent failure of the 
fuel feed pump, damage to the engine, and damage to the airplane.

(e) Actions and Compliance

    Comply with this AD within the compliance times specified, 
unless already done. Remove from service each affected fuel feed 
pump before it exceeds 600 operating hours (OH) time in service 
(TIS) or within 110 OH after the effective date of this AD, 
whichever occurs later.

(f) Installation Prohibition

    After the effective date of this AD, do not install onto any 
engine, any fuel feed pump, P/N 05-7312-K0073xx or P/N 05-7312-
K0133xx, where ``xx'' can be any number, if the fuel feed pump has 
600 hours or more TIS. If TIS of a fuel feed pump is unknown or has 
exceeded 600 hours TIS, then the fuel feed pump is not eligible for 
installation. Rebuilt, overhauled, or repaired fuel feed pumps or 
fuel feed pumps that lack a serial number, are not eligible for 
installation.

(g) Related Information

    (1) For more information about this AD, Philip Haberlen, 
Aerospace Engineer, Engine Certification Office, FAA, Engine & 
Propeller Directorate, 1200 District Avenue, Burlington, MA 01803; 
phone: 781-238-7770; fax: 781-238-7199; email: 
philip.haberlen@faa.gov.
    (2) Refer to MCAI European Aviation Safety Agency AD 2015-0189, 
dated September 21, 2015, for more information. You may examine the 
MCAI in the AD docket on the Internet at https://www.regulations.gov 
by searching for and locating it in Docket No. FAA-2015-5193.
    (3) For service information identified in this AD, contact 
Technify Motors GmbH, Platanenstrasse 14, D-09356 Sankt Egidien, 
Germany; phone: +49-37204-696-0; fax: +49-37204-696-2912; email: 
support@continentaldiesel.de.
    (4) You may view this service information at the FAA, Engine & 
Propeller Directorate, 1200 District Avenue, Burlington, MA. For 
information on the availability of this material at the FAA, call 
781-238-7125.

(h) Material Incorporated by Reference

    None.

    Issued in Burlington, Massachusetts, on March 25, 2016.
Colleen M. D'Alessandro,
Manager, Engine & Propeller Directorate, Aircraft Certification 
Service.
[FR Doc. 2016-07376 Filed 4-1-16; 8:45 am]
 BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.