Airworthiness Directives; Airbus Airplanes, 12405-12409 [2016-04538]
Download as PDF
12405
Rules and Regulations
Federal Register
Vol. 81, No. 46
Wednesday, March 9, 2016
This section of the FEDERAL REGISTER
contains regulatory documents having general
applicability and legal effect, most of which
are keyed to and codified in the Code of
Federal Regulations, which is published under
50 titles pursuant to 44 U.S.C. 1510.
The Code of Federal Regulations is sold by
the Superintendent of Documents. Prices of
new books are listed in the first FEDERAL
REGISTER issue of each week.
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA–2015–3149; Directorate
Identifier 2015–NM–014–AD; Amendment
39–18394; AD 2016–03–07]
RIN 2120–AA64
Airworthiness Directives; Airbus
Airplanes
Federal Aviation
Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
AGENCY:
We are adopting a new
airworthiness directive (AD) for all
Airbus Model A330–200, –200
Freighter, and –300 series airplanes, and
all Airbus Model A340–200, –300, –500,
and –600 series airplanes. This AD was
prompted by reports of premature aging
of certain chemical oxygen generators in
the passenger compartment that resulted
in failure of the generators to activate.
This AD requires inspecting to
determine if certain passenger chemical
oxygen generators are installed, and
replacement of affected generators. We
are issuing this AD to prevent failure of
the chemical oxygen generator to
activate during an emergency situation,
which could result in unavailability of
oxygen and possible incapacitation of
the occupants.
DATES: This AD becomes effective April
13, 2016.
The Director of the Federal Register
approved the incorporation by reference
of certain publications listed in this AD
as of April 13, 2016.
ADDRESSES: You may examine the AD
docket on the Internet at https://
www.regulations.gov/#!docket
Detail;D=FAA-2015-3149; or in person
at the Docket Management Facility, U.S.
Department of Transportation, Docket
Lhorne on DSK5TPTVN1PROD with RULES
SUMMARY:
VerDate Sep<11>2014
14:06 Mar 08, 2016
Jkt 238001
Operations, M–30, West Building
Ground Floor, Room W12–140, 1200
New Jersey Avenue SE., Washington,
DC.
For Airbus service information
identified in this final rule, contact
Airbus SAS, Airworthiness Office—
EAL, 1 Rond Point Maurice Bellonte,
31707 Blagnac Cedex, France; telephone
+33 5 61 93 36 96; fax +33 5 61 93 45
80; email airworthiness.A330–A340@
airbus.com; Internet https://
www.airbus.com.
For B/E Aerospace service
information identified in this final rule,
contact B/E Aerospace Inc., 10800
Pflumm Road, Lenexa, KS 66215;
telephone 913–338–9800; fax 913–469–
8419; Internet https://beaerospace.com/
home/globalsupport.
You may view this referenced service
information at the FAA, Transport
Airplane Directorate, 1601 Lind Avenue
SW., Renton, WA. For information on
the availability of this material at the
FAA, call 425–227–1221. It is also
available on the Internet at https://
www.regulations.gov by searching for
and locating Docket No. FAA–2015–
3149.
FOR FURTHER INFORMATION CONTACT:
Vladimir Ulyanov, Aerospace Engineer,
International Branch, ANM–116,
Transport Airplane Directorate, FAA,
1601 Lind Avenue SW., Renton, WA
98057–3356; telephone 425–227–1138;
fax 425–227–1149.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed
rulemaking (NPRM) to amend 14 CFR
part 39 by adding an AD that would
apply to all Airbus Model A330–200,
–200 Freighter, and –300 series
airplanes; and all Airbus Model A340–
200, –300, –500, and –600 series
airplanes. The NPRM published in the
Federal Register on August 31, 2015 (80
FR 52419).
The European Aviation Safety Agency
(EASA), which is the Technical Agent
for the Member States of the European
Union, has issued EASA Airworthiness
Directive 2015–0119, dated June 24,
2015, correction January 12, 2016
(referred to after this as the Mandatory
Continuing Airworthiness Information,
or ‘‘the MCAI’’), to correct an unsafe
condition for all Airbus Model A330–
200, –200 Freighter, and –300 series
airplanes; and Model A340–200, –300,
PO 00000
Frm 00001
Fmt 4700
Sfmt 4700
–500, and –600 series airplanes. The
MCAI states:
Reports have been received indicating
premature ageing of certain passenger
chemical oxygen generators, Part Number (P/
N) 117042–XX (XX representing any
numerical value), manufactured by B/E
Aerospace. Some operators reported that
when they tried to activate generators, some
older units failed to activate. Given the
number of failed units reported, all the
generators manufactured in 1999, 2000, and
2001 were considered unreliable.
This condition, if not corrected, could lead
to failure of the generator to activate and
consequently not deliver oxygen during an
emergency, possibly resulting in injury to
aeroplane occupants.
To address this potential unsafe condition,
Airbus issued Alert Operators Transmission
(AOT) A35L007–14, making reference to B/
E Aerospace Service Information Letter (SIL)
D1019–01 (currently at Revision 1) and B/E
Aerospace Service Bulletin (SB) 117042–35–
001. Consequently, EASA issued AD 2014–
0277 to require identification and
replacement of the affected oxygen
generators.
Since EASA AD 2014–0277 was issued,
and following new investigation results,
EASA has decided to introduce a life
limitation concerning all P/N 117042–XX
chemical oxygen generators, manufactured
by B/E Aerospace.
For the reason described above, this EASA
AD retains the requirements of EASA AD
2014–0277, which is superseded, expands
the scope of the AD to include chemical
oxygen generators manufactured after 2001,
and requires their removal from service
before exceeding 10 years since date of
manufacture.
This [EASA] AD was republished to correct
a typographical error in the applicability.
You may examine the MCAI in the
AD docket on the Internet at https://
www.regulations.gov/#!document
Detail;D=FAA-2015-3149-0002.
Comments
We gave the public the opportunity to
participate in developing this AD. The
following presents the comment
received on the NPRM (80 FR 52419,
August 31, 2015) and the FAA’s
response.
Request To Remove Operator
Identification
Airbus asked that we remove the
operator identification from the
chemical oxygen generator pictured in
Figure 2 to paragraph (g) of the
proposed AD (80 FR 52419, August 31,
2015). Airbus stated that Figure 2 to
paragraph (g) should replicate Figure 2
E:\FR\FM\09MRR1.SGM
09MRR1
12406
Federal Register / Vol. 81, No. 46 / Wednesday, March 9, 2016 / Rules and Regulations
in EASA AD 2015–0119, dated June 24,
2015, which was published with no
signs or references to an operator.
We agree with the commenter for the
reason provided. We have changed the
oxygen generator picture in Figure 2 to
paragraph (g) of this AD accordingly.
Clarification of Oxygen Generators for
Replacement
We have revised paragraph (i) in this
AD to clarify the identity of the oxygen
generators to be replaced.
Conclusion
We reviewed the relevant data,
considered the comment received, and
determined that air safety and the
public interest require adopting this AD
with the change described previously
and minor editorial changes. We have
determined that these minor changes:
• Are consistent with the intent that
was proposed in the NPRM (80 FR
52419, August 31, 2015) for correcting
the unsafe condition; and
• Do not add any additional burden
upon the public than was already
proposed in the NPRM (80 FR 52419,
August 31, 2015).
Related Service Information Under 1
CFR Part 51
Airbus has issued Alert Operators
Transmission (AOT) A35L007–14,
Revision 01, June 17, 2015; including
Appendix A, Revision 01, dated June
17, 2015. B/E Aerospace has issued
Service Bulletin 117042–35–001, dated
December 10, 2014. The service
information describes procedures for
inspecting to determine if certain
passenger chemical oxygen generators
are installed, and replacing affected
generators. This service information is
reasonably available because the
interested parties have access to it
through their normal course of business
or by the means identified in the
ADDRESSES section.
Costs of Compliance
We estimate that this AD affects 91
airplanes of U.S. registry.
We estimate the following costs to
comply with this AD:
ESTIMATED COSTS
Cost on
U.S. operators
Action
Labor cost
Parts cost
Cost per product
Inspection ..........
1 work-hour × $85 per hour =
$85.
1 work hour × $85 per hour =
$85.
$0 ..........................................
$85 ........................................
$7,735.
$1,000 per oxygen generator
$1,085 per oxygen generator
$98,735 for one oxygen generator.
Replacement .....
Authority for This Rulemaking
Title 49 of the United States Code
specifies the FAA’s authority to issue
rules on aviation safety. Subtitle I,
section 106, describes the authority of
the FAA Administrator. ‘‘Subtitle VII:
Aviation Programs,’’ describes in more
detail the scope of the Agency’s
authority.
We are issuing this rulemaking under
the authority described in ‘‘Subtitle VII,
Part A, Subpart III, Section 44701:
General requirements.’’ Under that
section, Congress charges the FAA with
promoting safe flight of civil aircraft in
air commerce by prescribing regulations
for practices, methods, and procedures
the Administrator finds necessary for
safety in air commerce. This regulation
is within the scope of that authority
because it addresses an unsafe condition
that is likely to exist or develop on
products identified in this rulemaking
action.
Lhorne on DSK5TPTVN1PROD with RULES
Regulatory Findings
We determined that this AD will not
have federalism implications under
Executive Order 13132. This AD will
not have a substantial direct effect on
the States, on the relationship between
the national government and the States,
or on the distribution of power and
responsibilities among the various
levels of government.
For the reasons discussed above, I
certify that this AD:
VerDate Sep<11>2014
14:06 Mar 08, 2016
Jkt 238001
1. Is not a ‘‘significant regulatory
action’’ under Executive Order 12866;
2. Is not a ‘‘significant rule’’ under the
DOT Regulatory Policies and Procedures
(44 FR 11034, February 26, 1979);
3. Will not affect intrastate aviation in
Alaska; and
4. Will not have a significant
economic impact, positive or negative,
on a substantial number of small entities
under the criteria of the Regulatory
Flexibility Act.
Examining the AD Docket
You may examine the AD docket on
the Internet at https://
www.regulations.gov/#!docketDetail;D=
FAA-2015-3149; or in person at the
Docket Management Facility between 9
a.m. and 5 p.m., Monday through
Friday, except Federal holidays. The AD
docket contains this AD, the regulatory
evaluation, any comments received, and
other information. The street address for
the Docket Operations office (telephone
800–647–5527) is in the ADDRESSES
section.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation
safety, Incorporation by reference,
Safety.
Adoption of the Amendment
Accordingly, under the authority
delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as
follows:
PO 00000
Frm 00002
Fmt 4700
Sfmt 4700
PART 39—AIRWORTHINESS
DIRECTIVES
1. The authority citation for part 39
continues to read as follows:
■
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13
[Amended]
2. The FAA amends § 39.13 by adding
the following new airworthiness
directive (AD):
■
2016–03–07 Airbus: Amendment 39–18394.
Docket No. FAA–2015–3149; Directorate
Identifier 2015–NM–014–AD.
(a) Effective Date
This AD becomes effective April 13, 2016.
(b) Affected ADs
None.
(c) Applicability
This AD applies to the airplanes,
certificated in any category, identified in
paragraphs (c)(1) and (c)(2) of this AD, all
manufacturer serial numbers; except those on
which a gaseous system for all oxygen
generators is installed.
(1) Airbus Model A330–201, –202, –203,
–223, –223F, –243, –243F, –301, –302, –303,
–321, –322, –323, –341, –342, and –343
airplanes.
(2) Airbus Model A340–211, –212, –213,
–311, –312, –313, –541, and –642 airplanes.
(d) Subject
Air Transport Association (ATA) of
America Code 35, Oxygen.
(e) Reason
This AD was prompted by reports of
premature aging of certain chemical oxygen
E:\FR\FM\09MRR1.SGM
09MRR1
Federal Register / Vol. 81, No. 46 / Wednesday, March 9, 2016 / Rules and Regulations
(f) Compliance
Lhorne on DSK5TPTVN1PROD with RULES
Comply with this AD within the
compliance times specified, unless already
done.
VerDate Sep<11>2014
14:06 Mar 08, 2016
Jkt 238001
(g) Inspection
Within 30 days after the effective date of
this AD: Inspect each passenger chemical
oxygen generator to identify the date of
manufacture (refer to figures 1 and 2 to
paragraph (g) of this AD for the location of
the date) of each passenger chemical oxygen
generator having any part number (P/N)
listed in paragraphs (g)(1) through (g)(6) of
this AD, in accordance with the Instructions
of Airbus Alert Operators Transmission
(AOT) A35L007–14, Revision 01, June 17,
2015, including Appendix A, Revision 01,
PO 00000
Frm 00003
Fmt 4700
Sfmt 4725
dated June 17, 2015. A review of airplane
maintenance records is acceptable in lieu of
this inspection if the date of manufacture of
the generator can be conclusively determined
from that review.
(1) 117042–02 (15 minutes (min)—2
masks).
(2) 117042–03 (15 min—3 masks).
(3) 117042–04 (15 min—4 masks).
(4) 117042–22 (22 min—2 masks).
(5) 117042–23 (22 min—3 masks).
(6) 117042–24 (22 min—4 masks).
E:\FR\FM\09MRR1.SGM
09MRR1
ER09MR16.000
generators in the passenger compartment that
resulted in failure of the generators to
activate. We are issuing this AD to prevent
failure of the chemical oxygen generator to
activate during an emergency situation,
which could result in unavailability of
oxygen and possible incapacitation of the
occupants.
12407
Federal Register / Vol. 81, No. 46 / Wednesday, March 9, 2016 / Rules and Regulations
(h) Replacement of Pre-2002 Passenger
Oxygen Generators
If, during any inspection required by
paragraph (g) of this AD, any passenger
chemical oxygen generator having a date of
manufacture of 1999, 2000, or 2001 is found:
At the time specified in paragraph (h)(1),
(h)(2), or (h)(3) of this AD, as applicable,
replace the affected passenger chemical
oxygen generator, in accordance with the
Instructions of Airbus AOT A35L007–14,
Revision 01, June 17, 2015; including
Appendix A, Revision 01, dated June 17,
2015 (for 15- and 22-minute passenger
chemical oxygen generators); or in
accordance with the Accomplishment
Instructions of B/E Aerospace Service
Bulletin 117042–35–001, dated December 10,
2014 (for 15-minute passenger chemical
oxygen generators).
(1) For units manufactured in 1999: Within
30 days after the effective date of this AD.
(2) For units manufactured in 2000: Within
6 months after the effective date of this AD.
VerDate Sep<11>2014
14:06 Mar 08, 2016
Jkt 238001
(3) For units manufactured in 2001: Within
12 months after the effective date of this AD.
(i) Replacement of 2002 or Later Passenger
Oxygen Generators
If, during any inspection required by
paragraph (g) of this AD, any passenger
chemical oxygen generator having a date of
manufacture of 2002 or later is found: At the
time specified in paragraph (i)(1), (i)(2), (i)(3),
(i)(4), (i)(5), (i)(6), (i)(7), or (i)(8) of this AD,
as applicable, replace the affected passenger
chemical oxygen generator with a serviceable
unit, in accordance with the Instructions of
Airbus AOT A35L007–14, Revision 01, June
17, 2015; including Appendix A, Revision
01, dated June 17, 2015 (for 15- and 22minute passenger chemical oxygen
generators); or in accordance with the
Accomplishment Instructions of B/E
Aerospace Service Bulletin 117042–35–001,
dated December 10, 2014 (for 15-minute
passenger chemical oxygen generators).
PO 00000
Frm 00004
Fmt 4700
Sfmt 4700
(1) For units manufactured in 2002: Within
12 months after the effective date of this AD.
(2) For units manufactured in 2003: Within
16 months after the effective date of this AD.
(3) For units manufactured in 2004: Within
20 months after the effective date of this AD.
(4) For units manufactured in 2005: Within
24 months after the effective date of this AD.
(5) For units manufactured in 2006: Within
28 months after the effective date of this AD.
(6) For units manufactured in 2007: Within
32 months after the effective date of this AD.
(7) For units manufactured in 2008: Within
36 months after the effective date of this AD.
(8) For units manufactured in 2009 or later:
Before the accumulation of 10 years since
date of manufacture.
(j) Definition of a Serviceable Unit
A serviceable unit is an oxygen generator
having P/N 117042–XX, with a
manufacturing date not older than 10 years,
or any other FAA-approved part number,
provided that the generator has not exceeded
E:\FR\FM\09MRR1.SGM
09MRR1
ER09MR16.001
Lhorne on DSK5TPTVN1PROD with RULES
12408
Federal Register / Vol. 81, No. 46 / Wednesday, March 9, 2016 / Rules and Regulations
the life limit established by the manufacturer
for that generator.
(k) Credit for Previous Actions
This paragraph provides credit for the
applicable actions required by paragraphs (g),
(h), and (i) of this AD, if those actions were
performed before the effective date of this AD
using Airbus AOT A35L007–14, dated
December 18, 2014.
(l) Parts Installation Limitation
As of the effective date of this AD, no
person may install a passenger chemical
oxygen generator on any airplane, unless the
passenger chemical oxygen generator is
determined to be a serviceable unit, as
defined in paragraph (j) of this AD.
(m) Other FAA AD Provisions
Lhorne on DSK5TPTVN1PROD with RULES
The following provisions also apply to this
AD:
(1) Alternative Methods of Compliance
(AMOCs): The Manager, International
Branch, ANM–116, Transport Airplane
Directorate, FAA, has the authority to
approve AMOCs for this AD, if requested
using the procedures found in 14 CFR 39.19.
In accordance with 14 CFR 39.19, send your
request to your principal inspector or local
Flight Standards District Office, as
appropriate. If sending information directly
to the International Branch, send it to ATTN:
Vladimir Ulyanov, Aerospace Engineer,
International Branch, ANM–116, Transport
Airplane Directorate, FAA, 1601 Lind
Avenue SW., Renton, WA 98057–3356;
telephone 425–227–1138; fax 425–227–1149.
Information may be emailed to: 9-ANM-116AMOC-REQUESTS@faa.gov. Before using
any approved AMOC, notify your appropriate
principal inspector, or lacking a principal
inspector, the manager of the local flight
standards district office/certificate holding
district office. The AMOC approval letter
must specifically reference this AD.
(2) Contacting the Manufacturer: For any
requirement in this AD to obtain corrective
actions from a manufacturer, the action must
be accomplished using a method approved
by the Manager, International Branch, ANM–
116, Transport Airplane Directorate, FAA; or
the European Aviation Safety Agency
(EASA); or Airbus’s EASA Design
Organization Approval (DOA). If approved by
the DOA, the approval must include the
DOA-authorized signature.
(n) Related Information
(1) Refer to Mandatory Continuing
Airworthiness Information (MCAI) EASA
Airworthiness Directive 2015–0119, dated
June 24, 2015, correction January 12, 2016,
for related information. This MCAI may be
found in the AD docket on the Internet at
https://www.regulations.gov by searching for
and locating Docket No. FAA–2015–3149.
(2) Service information identified in this
AD that is not incorporated by reference is
available at the addresses specified in
paragraphs (o)(3) and (o)(5) of this AD.
(o) Material Incorporated by Reference
(1) The Director of the Federal Register
approved the incorporation by reference
(IBR) of the service information listed in this
VerDate Sep<11>2014
14:06 Mar 08, 2016
Jkt 238001
paragraph under 5 U.S.C. 552(a) and 1 CFR
part 51.
(2) You must use this service information
as applicable to do the actions required by
this AD, unless this AD specifies otherwise.
(i) Airbus Alert Operators Transmission
(AOT) A35L007–14, Revision 01, June 17,
2015; including Appendix A, Revision 01,
dated June 17, 2015. The revision date is not
shown on Appendix A.
(ii) B/E Aerospace Service Bulletin
117042–35–001, dated December 10, 2014.
(3) For Airbus service information
identified in this AD, contact Airbus SAS,
Airworthiness Office—EAL, 1 Rond Point
Maurice Bellonte, 31707 Blagnac Cedex,
France; telephone +33 5 61 93 36 96; fax +33
5 61 93 45 80; email airworthiness.A330A340@airbus.com; Internet https://
www.airbus.com.
(4) For B/E Aerospace service information
identified in this AD, contact B/E Aerospace
Inc., 10800 Pflumm Road, Lenexa, KS 66215;
telephone 913–338–9800; fax 913–469–8419;
Internet https://beaerospace.com/home/global
support.
(5) You may view this service information
at the FAA, Transport Airplane Directorate,
1601 Lind Avenue SW., Renton, WA. For
information on the availability of this
material at the FAA, call 425–227–1221.
(6) You may view this service information
that is incorporated by reference at the
National Archives and Records
Administration (NARA). For information on
the availability of this material at NARA, call
202–741–6030, or go to: https://
www.archives.gov/federal-register/cfr/ibrlocations.html.
Issued in Renton, Washington, on February
19, 2016.
Dorr M. Anderson,
Acting Manager, Transport Airplane
Directorate, Aircraft Certification Service.
[FR Doc. 2016–04538 Filed 3–8–16; 8:45 am]
BILLING CODE 4910–13–P
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA–2015–0243; Directorate
Identifier 2014–NM–114–AD; Amendment
39–18423; AD 2016–05–05]
RIN 2120–AA64
Airworthiness Directives; Airbus
Airplanes
Federal Aviation
Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
AGENCY:
We are adopting a new
airworthiness directive (AD) for all
Airbus Model A300 series airplanes;
Model A300 B4–600, B4–600R, and F4–
600R series airplanes, and A300 C4–
605R Variant F airplanes (collectively
SUMMARY:
PO 00000
Frm 00005
Fmt 4700
Sfmt 4700
12409
called Model A300–600 series
airplanes); and Model A310 series
airplanes. This AD was prompted by
reports of cracked aluminum support
struts of the trimmable horizontal
stabilizer (THS) caused by stress
corrosion. This AD requires inspections
to identify the part number of each
support strut, repetitive inspections for
cracking of the THS support strut ends,
installation of reinforcing clamps on
strut ends, and replacement of support
struts, if necessary. We are issuing this
AD to detect and correct cracked THS
support struts, which could lead to the
rupture of all four support struts making
the remaining structure unable to carry
limit loads, which could result in loss
of the THS and reduced control of the
airplane.
DATES: This AD becomes effective April
13, 2016.
The Director of the Federal Register
approved the incorporation by reference
of certain publications listed in this AD
as of April 13, 2016.
ADDRESSES: You may examine the AD
docket on the Internet at https://
www.regulations.gov/#!docket
Detail;D=FAA-2015-0243 or in person at
the Docket Management Facility, U.S.
Department of Transportation, Docket
Operations, M–30, West Building
Ground Floor, Room W12–140, 1200
New Jersey Avenue SE., Washington,
DC.
For service information identified in
this final rule, contact Airbus SAS,
Airworthiness Office—EAW, 1 Rond
Point Maurice Bellonte, 31707 Blagnac
Cedex, France; telephone +33 5 61 93 36
96; fax +33 5 61 93 44 51; email
account.airworth-eas@airbus.com;
Internet https://www.airbus.com. You
may view this referenced service
information at the FAA, Transport
Airplane Directorate, 1601 Lind Avenue
SW., Renton, WA. For information on
the availability of this material at the
FAA, call 425–227–1221. It is also
available on the Internet at https://
www.regulations.gov by searching for
and locating Docket No. FAA–2015–
0243.
FOR FURTHER INFORMATION CONTACT: Dan
Rodina, Aerospace Engineer,
International Branch, ANM–116,
Transport Airplane Directorate, FAA,
1601 Lind Avenue SW., Renton, WA
98057–3356; telephone 425–227–2125;
fax 425–227–1149.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed
rulemaking (NPRM) to amend 14 CFR
part 39 by adding an AD that would
apply to all Airbus Model A300 series
E:\FR\FM\09MRR1.SGM
09MRR1
Agencies
[Federal Register Volume 81, Number 46 (Wednesday, March 9, 2016)]
[Rules and Regulations]
[Pages 12405-12409]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-04538]
========================================================================
Rules and Regulations
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains regulatory documents
having general applicability and legal effect, most of which are keyed
to and codified in the Code of Federal Regulations, which is published
under 50 titles pursuant to 44 U.S.C. 1510.
The Code of Federal Regulations is sold by the Superintendent of Documents.
Prices of new books are listed in the first FEDERAL REGISTER issue of each
week.
========================================================================
Federal Register / Vol. 81, No. 46 / Wednesday, March 9, 2016 / Rules
and Regulations
[[Page 12405]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2015-3149; Directorate Identifier 2015-NM-014-AD;
Amendment 39-18394; AD 2016-03-07]
RIN 2120-AA64
Airworthiness Directives; Airbus Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for all
Airbus Model A330-200, -200 Freighter, and -300 series airplanes, and
all Airbus Model A340-200, -300, -500, and -600 series airplanes. This
AD was prompted by reports of premature aging of certain chemical
oxygen generators in the passenger compartment that resulted in failure
of the generators to activate. This AD requires inspecting to determine
if certain passenger chemical oxygen generators are installed, and
replacement of affected generators. We are issuing this AD to prevent
failure of the chemical oxygen generator to activate during an
emergency situation, which could result in unavailability of oxygen and
possible incapacitation of the occupants.
DATES: This AD becomes effective April 13, 2016.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in this AD as of April 13,
2016.
ADDRESSES: You may examine the AD docket on the Internet at https://www.regulations.gov/#!docketDetail;D=FAA-2015-3149; or in person at the
Docket Management Facility, U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE., Washington, DC.
For Airbus service information identified in this final rule,
contact Airbus SAS, Airworthiness Office--EAL, 1 Rond Point Maurice
Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax
+33 5 61 93 45 80; email airworthiness.A330-A340@airbus.com; Internet
https://www.airbus.com.
For B/E Aerospace service information identified in this final
rule, contact B/E Aerospace Inc., 10800 Pflumm Road, Lenexa, KS 66215;
telephone 913-338-9800; fax 913-469-8419; Internet https://beaerospace.com/home/globalsupport.
You may view this referenced service information at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For
information on the availability of this material at the FAA, call 425-
227-1221. It is also available on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2015-
3149.
FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer,
International Branch, ANM-116, Transport Airplane Directorate, FAA,
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1138;
fax 425-227-1149.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
part 39 by adding an AD that would apply to all Airbus Model A330-200,
-200 Freighter, and -300 series airplanes; and all Airbus Model A340-
200, -300, -500, and -600 series airplanes. The NPRM published in the
Federal Register on August 31, 2015 (80 FR 52419).
The European Aviation Safety Agency (EASA), which is the Technical
Agent for the Member States of the European Union, has issued EASA
Airworthiness Directive 2015-0119, dated June 24, 2015, correction
January 12, 2016 (referred to after this as the Mandatory Continuing
Airworthiness Information, or ``the MCAI''), to correct an unsafe
condition for all Airbus Model A330-200, -200 Freighter, and -300
series airplanes; and Model A340-200, -300, -500, and -600 series
airplanes. The MCAI states:
Reports have been received indicating premature ageing of
certain passenger chemical oxygen generators, Part Number (P/N)
117042-XX (XX representing any numerical value), manufactured by B/E
Aerospace. Some operators reported that when they tried to activate
generators, some older units failed to activate. Given the number of
failed units reported, all the generators manufactured in 1999,
2000, and 2001 were considered unreliable.
This condition, if not corrected, could lead to failure of the
generator to activate and consequently not deliver oxygen during an
emergency, possibly resulting in injury to aeroplane occupants.
To address this potential unsafe condition, Airbus issued Alert
Operators Transmission (AOT) A35L007-14, making reference to B/E
Aerospace Service Information Letter (SIL) D1019-01 (currently at
Revision 1) and B/E Aerospace Service Bulletin (SB) 117042-35-001.
Consequently, EASA issued AD 2014-0277 to require identification and
replacement of the affected oxygen generators.
Since EASA AD 2014-0277 was issued, and following new
investigation results, EASA has decided to introduce a life
limitation concerning all P/N 117042-XX chemical oxygen generators,
manufactured by B/E Aerospace.
For the reason described above, this EASA AD retains the
requirements of EASA AD 2014-0277, which is superseded, expands the
scope of the AD to include chemical oxygen generators manufactured
after 2001, and requires their removal from service before exceeding
10 years since date of manufacture.
This [EASA] AD was republished to correct a typographical error
in the applicability.
You may examine the MCAI in the AD docket on the Internet at https://www.regulations.gov/#!documentDetail;D=FAA-2015-3149-0002.
Comments
We gave the public the opportunity to participate in developing
this AD. The following presents the comment received on the NPRM (80 FR
52419, August 31, 2015) and the FAA's response.
Request To Remove Operator Identification
Airbus asked that we remove the operator identification from the
chemical oxygen generator pictured in Figure 2 to paragraph (g) of the
proposed AD (80 FR 52419, August 31, 2015). Airbus stated that Figure 2
to paragraph (g) should replicate Figure 2
[[Page 12406]]
in EASA AD 2015-0119, dated June 24, 2015, which was published with no
signs or references to an operator.
We agree with the commenter for the reason provided. We have
changed the oxygen generator picture in Figure 2 to paragraph (g) of
this AD accordingly.
Clarification of Oxygen Generators for Replacement
We have revised paragraph (i) in this AD to clarify the identity of
the oxygen generators to be replaced.
Conclusion
We reviewed the relevant data, considered the comment received, and
determined that air safety and the public interest require adopting
this AD with the change described previously and minor editorial
changes. We have determined that these minor changes:
Are consistent with the intent that was proposed in the
NPRM (80 FR 52419, August 31, 2015) for correcting the unsafe
condition; and
Do not add any additional burden upon the public than was
already proposed in the NPRM (80 FR 52419, August 31, 2015).
Related Service Information Under 1 CFR Part 51
Airbus has issued Alert Operators Transmission (AOT) A35L007-14,
Revision 01, June 17, 2015; including Appendix A, Revision 01, dated
June 17, 2015. B/E Aerospace has issued Service Bulletin 117042-35-001,
dated December 10, 2014. The service information describes procedures
for inspecting to determine if certain passenger chemical oxygen
generators are installed, and replacing affected generators. This
service information is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in the ADDRESSES section.
Costs of Compliance
We estimate that this AD affects 91 airplanes of U.S. registry.
We estimate the following costs to comply with this AD:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost on U.S.
Action Labor cost Parts cost Cost per product operators
----------------------------------------------------------------------------------------------------------------
Inspection............... 1 work-hour x $85 $0.................. $85................. $7,735.
per hour = $85.
Replacement.............. 1 work hour x $85 $1,000 per oxygen $1,085 per oxygen $98,735 for one
per hour = $85. generator. generator. oxygen generator.
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979);
3. Will not affect intrastate aviation in Alaska; and
4. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
Examining the AD Docket
You may examine the AD docket on the Internet at https://www.regulations.gov/#!docketDetail;D=FAA-2015-3149; or in person at the
Docket Management Facility between 9 a.m. and 5 p.m., Monday through
Friday, except Federal holidays. The AD docket contains this AD, the
regulatory evaluation, any comments received, and other information.
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
2016-03-07 Airbus: Amendment 39-18394. Docket No. FAA-2015-3149;
Directorate Identifier 2015-NM-014-AD.
(a) Effective Date
This AD becomes effective April 13, 2016.
(b) Affected ADs
None.
(c) Applicability
This AD applies to the airplanes, certificated in any category,
identified in paragraphs (c)(1) and (c)(2) of this AD, all
manufacturer serial numbers; except those on which a gaseous system
for all oxygen generators is installed.
(1) Airbus Model A330-201, -202, -203, -223, -223F, -243, -243F,
-301, -302, -303, -321, -322, -323, -341, -342, and -343 airplanes.
(2) Airbus Model A340-211, -212, -213, -311, -312, -313, -541,
and -642 airplanes.
(d) Subject
Air Transport Association (ATA) of America Code 35, Oxygen.
(e) Reason
This AD was prompted by reports of premature aging of certain
chemical oxygen
[[Page 12407]]
generators in the passenger compartment that resulted in failure of
the generators to activate. We are issuing this AD to prevent
failure of the chemical oxygen generator to activate during an
emergency situation, which could result in unavailability of oxygen
and possible incapacitation of the occupants.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Inspection
Within 30 days after the effective date of this AD: Inspect each
passenger chemical oxygen generator to identify the date of
manufacture (refer to figures 1 and 2 to paragraph (g) of this AD
for the location of the date) of each passenger chemical oxygen
generator having any part number (P/N) listed in paragraphs (g)(1)
through (g)(6) of this AD, in accordance with the Instructions of
Airbus Alert Operators Transmission (AOT) A35L007-14, Revision 01,
June 17, 2015, including Appendix A, Revision 01, dated June 17,
2015. A review of airplane maintenance records is acceptable in lieu
of this inspection if the date of manufacture of the generator can
be conclusively determined from that review.
(1) 117042-02 (15 minutes (min)--2 masks).
(2) 117042-03 (15 min--3 masks).
(3) 117042-04 (15 min--4 masks).
(4) 117042-22 (22 min--2 masks).
(5) 117042-23 (22 min--3 masks).
(6) 117042-24 (22 min--4 masks).
[GRAPHIC] [TIFF OMITTED] TR09MR16.000
[[Page 12408]]
[GRAPHIC] [TIFF OMITTED] TR09MR16.001
(h) Replacement of Pre-2002 Passenger Oxygen Generators
If, during any inspection required by paragraph (g) of this AD,
any passenger chemical oxygen generator having a date of manufacture
of 1999, 2000, or 2001 is found: At the time specified in paragraph
(h)(1), (h)(2), or (h)(3) of this AD, as applicable, replace the
affected passenger chemical oxygen generator, in accordance with the
Instructions of Airbus AOT A35L007-14, Revision 01, June 17, 2015;
including Appendix A, Revision 01, dated June 17, 2015 (for 15- and
22-minute passenger chemical oxygen generators); or in accordance
with the Accomplishment Instructions of B/E Aerospace Service
Bulletin 117042-35-001, dated December 10, 2014 (for 15-minute
passenger chemical oxygen generators).
(1) For units manufactured in 1999: Within 30 days after the
effective date of this AD.
(2) For units manufactured in 2000: Within 6 months after the
effective date of this AD.
(3) For units manufactured in 2001: Within 12 months after the
effective date of this AD.
(i) Replacement of 2002 or Later Passenger Oxygen Generators
If, during any inspection required by paragraph (g) of this AD,
any passenger chemical oxygen generator having a date of manufacture
of 2002 or later is found: At the time specified in paragraph
(i)(1), (i)(2), (i)(3), (i)(4), (i)(5), (i)(6), (i)(7), or (i)(8) of
this AD, as applicable, replace the affected passenger chemical
oxygen generator with a serviceable unit, in accordance with the
Instructions of Airbus AOT A35L007-14, Revision 01, June 17, 2015;
including Appendix A, Revision 01, dated June 17, 2015 (for 15- and
22-minute passenger chemical oxygen generators); or in accordance
with the Accomplishment Instructions of B/E Aerospace Service
Bulletin 117042-35-001, dated December 10, 2014 (for 15-minute
passenger chemical oxygen generators).
(1) For units manufactured in 2002: Within 12 months after the
effective date of this AD.
(2) For units manufactured in 2003: Within 16 months after the
effective date of this AD.
(3) For units manufactured in 2004: Within 20 months after the
effective date of this AD.
(4) For units manufactured in 2005: Within 24 months after the
effective date of this AD.
(5) For units manufactured in 2006: Within 28 months after the
effective date of this AD.
(6) For units manufactured in 2007: Within 32 months after the
effective date of this AD.
(7) For units manufactured in 2008: Within 36 months after the
effective date of this AD.
(8) For units manufactured in 2009 or later: Before the
accumulation of 10 years since date of manufacture.
(j) Definition of a Serviceable Unit
A serviceable unit is an oxygen generator having P/N 117042-XX,
with a manufacturing date not older than 10 years, or any other FAA-
approved part number, provided that the generator has not exceeded
[[Page 12409]]
the life limit established by the manufacturer for that generator.
(k) Credit for Previous Actions
This paragraph provides credit for the applicable actions
required by paragraphs (g), (h), and (i) of this AD, if those
actions were performed before the effective date of this AD using
Airbus AOT A35L007-14, dated December 18, 2014.
(l) Parts Installation Limitation
As of the effective date of this AD, no person may install a
passenger chemical oxygen generator on any airplane, unless the
passenger chemical oxygen generator is determined to be a
serviceable unit, as defined in paragraph (j) of this AD.
(m) Other FAA AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Branch, ANM-116, Transport Airplane Directorate, FAA,
has the authority to approve AMOCs for this AD, if requested using
the procedures found in 14 CFR 39.19. In accordance with 14 CFR
39.19, send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the International Branch, send it to ATTN: Vladimir
Ulyanov, Aerospace Engineer, International Branch, ANM-116,
Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton,
WA 98057-3356; telephone 425-227-1138; fax 425-227-1149. Information
may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any
approved AMOC, notify your appropriate principal inspector, or
lacking a principal inspector, the manager of the local flight
standards district office/certificate holding district office. The
AMOC approval letter must specifically reference this AD.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain corrective actions from a manufacturer, the action must be
accomplished using a method approved by the Manager, International
Branch, ANM-116, Transport Airplane Directorate, FAA; or the
European Aviation Safety Agency (EASA); or Airbus's EASA Design
Organization Approval (DOA). If approved by the DOA, the approval
must include the DOA-authorized signature.
(n) Related Information
(1) Refer to Mandatory Continuing Airworthiness Information
(MCAI) EASA Airworthiness Directive 2015-0119, dated June 24, 2015,
correction January 12, 2016, for related information. This MCAI may
be found in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2015-3149.
(2) Service information identified in this AD that is not
incorporated by reference is available at the addresses specified in
paragraphs (o)(3) and (o)(5) of this AD.
(o) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless this AD specifies otherwise.
(i) Airbus Alert Operators Transmission (AOT) A35L007-14,
Revision 01, June 17, 2015; including Appendix A, Revision 01, dated
June 17, 2015. The revision date is not shown on Appendix A.
(ii) B/E Aerospace Service Bulletin 117042-35-001, dated
December 10, 2014.
(3) For Airbus service information identified in this AD,
contact Airbus SAS, Airworthiness Office--EAL, 1 Rond Point Maurice
Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96;
fax +33 5 61 93 45 80; email airworthiness.A330-A340@airbus.com;
Internet https://www.airbus.com.
(4) For B/E Aerospace service information identified in this AD,
contact B/E Aerospace Inc., 10800 Pflumm Road, Lenexa, KS 66215;
telephone 913-338-9800; fax 913-469-8419; Internet https://beaerospace.com/home/globalsupport.
(5) You may view this service information at the FAA, Transport
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For
information on the availability of this material at the FAA, call
425-227-1221.
(6) You may view this service information that is incorporated
by reference at the National Archives and Records Administration
(NARA). For information on the availability of this material at
NARA, call 202-741-6030, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.
Issued in Renton, Washington, on February 19, 2016.
Dorr M. Anderson,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2016-04538 Filed 3-8-16; 8:45 am]
BILLING CODE 4910-13-P