Airworthiness Directives; Airbus Airplanes, 50863-50867 [2014-20262]

Download as PDF Federal Register / Vol. 79, No. 165 / Tuesday, August 26, 2014 / Proposed Rules (k) Incorporation of Critical Design Configuration Control Limitations (CDCCL) Items Within 60 days after the effective date of this AD, revise the maintenance or inspection program, as applicable, to incorporate the CDCCL items specified in Bombardier Temporary Revision ALI–112, dated January 11, 2011, to Section 5–1, ‘‘Critical Design Configuration Control Limitations,’’ of Part 2, ‘‘Airworthiness Limitation Items,’’ of Bombardier Q400 Dash 8 Maintenance Requirements Manual PSM 1–84–7. The maintenance program revision required by this paragraph may be done by inserting a copy of Bombardier Temporary Revision ALI–112, dated January 11, 2011, into the Airworthiness Limitation Items section of Bombardier Q400 Dash 8 Maintenance Requirements Manual PSM 1–84–7. When Bombardier Temporary Revision ALI–112, dated January 11, 2011, has been included in the general revisions of the manual, the general revisions may be inserted into the manual, and this temporary revision may be removed, provided the relevant information in the general revision is identical to that in Bombardier Temporary Revision ALI–112. (l) No Alternative Actions, Intervals, and CDCCLs After the maintenance or inspection program, as applicable, has been revised as required by paragraphs (j) and (k) of this AD, no alternative actions (e.g., inspections), intervals, or CDCCLs may be used unless the actions, intervals, or CDCCL are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (o)(1) of this AD. (m) Exception to Certain Service Information Where the service information, Bombardier Service Bulletin 84–28–09, Revision D, dated December 21, 2012; and Bombardier Service Bulletin 84–28–15, dated August 15, 2012; specify contacting the manufacturer for corrective action during accomplishment of the actions in those service bulletins: Before further flight, repair the discrepancy using a method approved by the Manager, New York Aircraft Certification Office (ACO), FAA; or Transport Canada Civil Aviation (TCCA); or Bombardier, Inc.’s TCCA Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAOauthorized signature. tkelley on DSK3SPTVN1PROD with PROPOSALS (n) Credit for Previous Actions This paragraph provides credit for actions required by paragraph (i)(1) of this AD, if those actions were performed before the effective date of this AD using Bombardier Service Bulletin 84–28–10, dated December 6, 2011; or Revision A, dated May 15, 2012; which are not incorporated by reference in this AD. (o) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, New York Aircraft Certification Office (ACO), ANE–170, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found VerDate Mar<15>2010 16:42 Aug 25, 2014 Jkt 232001 in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the ACO, send it to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516–228–7300; fax 516–794–5531. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. The AMOC approval letter must specifically reference this AD. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, New York ACO, ANE–170, Engine and Propeller Directorate, FAA; or Transport Canada Civil Aviation (TCCA); or Bombardier, Inc.’s TCCA Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAOauthorized signature. (p) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) Canadian Airworthiness Directive CF–2013–09R1, dated May 28, 2013, for related information. This MCAI may be found in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2014–0583. (2) For service information identified in this AD, contact Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt Boulevard, Toronto, Ontario M3K 1Y5, Canada; telephone 416–375–4000; fax 416–375–4539; email thd.qseries@aero.bombardier.com; Internet https://www.bombardier.com. You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Issued in Renton, Washington, on August 15, 2014. Michael Kaszycki, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2014–20263 Filed 8–25–14; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2014–0584; Directorate Identifier 2014–NM–092–AD] RIN 2120–AA64 Airworthiness Directives; Airbus Airplanes Federal Aviation Administration (FAA), DOT. AGENCY: PO 00000 Frm 00008 Fmt 4702 Sfmt 4702 50863 Notice of proposed rulemaking (NPRM). ACTION: We propose to supersede Airworthiness Directive (AD) 2014–09– 05, for certain Airbus Model A330–200 and –300 series airplanes, and Model A340–200 and –300 series airplanes. AD 2014–09–05 currently requires repetitive inspections of certain sidestay upper cardan pins of the main landing gear (MLG), and associated nuts and retainer assemblies, and pin replacement if necessary. Since we issued AD 2014–09–05, we have determined that a previously optional measurement is necessary to address the identified unsafe condition. We are proposing this AD to detect and correct migration of the sidestay upper cardan pin, which could result in disconnection of the sidestay upper arm from the airplane structure, and could result in a landing gear collapse and consequent damage to the airplane and injury to occupants. DATES: We must receive comments on this proposed AD by October 10, 2014. ADDRESSES: You may send comments by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Airbus SAS— Airworthiness Office—EAL, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 45 80; email airworthiness.A330-A340@airbus.com; Internet https://www.airbus.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. SUMMARY: Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2014– 0584; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, E:\FR\FM\26AUP1.SGM 26AUP1 50864 Federal Register / Vol. 79, No. 165 / Tuesday, August 26, 2014 / Proposed Rules except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; telephone 425–227–1138; fax 425–227–1149. SUPPLEMENTARY INFORMATION: tkelley on DSK3SPTVN1PROD with PROPOSALS Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2014–0584; Directorate Identifier 2014–NM–092–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion On April 16, 2014, we issued AD 2014–09–05, Amendment 39–17840 (79 FR 23909, April 29, 2014). AD 2014–09– 05 requires actions intended to address an unsafe condition on certain Airbus Model A330–200 and –300 series airplanes, and Model A340–200 and –300 series airplanes. Since we issued AD 2014–09–05, Amendment 39–17840 (79 FR 23909, April 29, 2014), we have determined that the optional measurement specified in that AD is necessary to address the identified unsafe condition. The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued EASA Airworthiness Directive 2014–0066, corrected March 20, 2014 (referred to after this as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition on certain Airbus Model A330–200 and –300 series airplanes, and Model A340– 200 and –300 series airplanes. The MCAI states: VerDate Mar<15>2010 16:42 Aug 25, 2014 Jkt 232001 An A330 aeroplane equipped with Basic (main landing gear) MLG was rolling out after landing when it experienced a nose wheel steering fault (unrelated to the safety subject addressed by this [EASA] AD), which resulted in the crew stopping the aeroplane on the taxiway after vacating the runway. The subsequent investigation revealed that the right-hand MLG sidestay upper cardan pin had migrated out of position. The sidestay upper cardan nut and retainer were found in the landing gear bay detached from the upper cardan pin. The nut and the retainer were still bolted together. This condition, if not detected and corrected, could lead to a complete migration of the sidestay upper cardan pin and a disconnection of the sidestay upper arm from the aeroplane structure, possibly resulting in MLG collapse with consequent damage to the aeroplane and injury to occupants. To address this potential condition, Airbus published Alert Operators Transmission (AOT) A32L003–14, providing inspection instructions. For the reasons described above, this [EASA] AD requires accomplishment of repetitive [detailed inspections for visible chrome] of the MLG upper cardan pin, nut and retainer [and pin replacement if necessary]. This [EASA] AD also requires accomplishment of a gap check between wing rear spar fitting lugs and the bush flanges [and corrective actions if necessary. Corrective actions include repair or replacement of the cardan pin assembly]. You may examine the MCAI in the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2014– 0584. FAA’s Determination and Requirements of This Proposed AD This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design. ‘‘Contacting the Manufacturer’’ Paragraph in This Proposed AD Since late 2006, we have included a standard paragraph titled ‘‘Airworthy Product’’ in all MCAI ADs in which the FAA develops an AD based on a foreign authority’s AD. The MCAI or referenced service information in an FAA AD often directs the owner/operator to contact the manufacturer for corrective actions, such as a repair. Briefly, the Airworthy Product paragraph allowed owners/ PO 00000 Frm 00009 Fmt 4702 Sfmt 4702 operators to use corrective actions provided by the manufacturer if those actions were FAA-approved. In addition, the paragraph stated that any actions approved by the State of Design Authority (or its delegated agent) are considered to be FAA-approved. In an NPRM having Directorate Identifier 2012–NM–101–AD (78 FR 78285, December 26, 2013), we proposed to prevent the use of repairs that were not specifically developed to correct the unsafe condition, by requiring that the repair approval provided by the State of Design Authority or its delegated agent specifically refer to the FAA AD. This change was intended to clarify the method of compliance and to provide operators with better visibility of repairs that are specifically developed and approved to correct the unsafe condition. In addition, we proposed to change the phrase ‘‘its delegated agent’’ to include a design approval holder (DAH) with State of Design Authority design organization approval (DOA), as applicable, to refer to a DAH authorized to approve required repairs for the proposed AD. One commenter to the NPRM having Directorate Identifier 2012–NM–101–AD (78 FR 78285, December 26, 2013) stated the following: ‘‘The proposed wording, being specific to repairs, eliminates the interpretation that Airbus messages are acceptable for approving minor deviations (corrective actions) needed during accomplishment of an AD mandated Airbus service bulletin.’’ This comment has made the FAA aware that some operators have misunderstood or misinterpreted the Airworthy Product paragraph to allow the owner/operator to use messages provided by the manufacturer as approval of deviations during the accomplishment of an AD-mandated action. The Airworthy Product paragraph does not approve messages or other information provided by the manufacturer for deviations to the requirements of the AD-mandated actions. The Airworthy Product paragraph only addresses the requirement to contact the manufacturer for corrective actions for the identified unsafe condition and does not cover deviations from other AD requirements. However, deviations to AD-required actions are addressed in 14 CFR 39.17, and anyone may request the approval for an alternative method of compliance to the AD-required actions using the procedures found in 14 CFR 39.19. To address this misunderstanding and misinterpretation of the Airworthy Product paragraph, we have changed the paragraph and retitled it ‘‘Contacting the E:\FR\FM\26AUP1.SGM 26AUP1 Federal Register / Vol. 79, No. 165 / Tuesday, August 26, 2014 / Proposed Rules tkelley on DSK3SPTVN1PROD with PROPOSALS Manufacturer.’’ This paragraph now clarifies that for any requirement in this proposed AD to obtain corrective actions from a manufacturer, the actions must be accomplished using a method approved by the FAA, the European Aviation Safety Agency (EASA), or Airbus’s EASA DOA. The Contacting the Manufacturer paragraph also clarifies that, if approved by the DOA, the approval must include the DOA-authorized signature. The DOA signature indicates that the data and information contained in the document are EASA-approved, which is also FAAapproved. Messages and other information provided by the manufacturer that do not contain the DOA-authorized signature approval are not EASA-approved, unless EASA directly approves the manufacturer’s message or other information. This clarification does not remove flexibility previously afforded by the Airworthy Product paragraph. Consistent with long-standing FAA policy, such flexibility was never intended for required actions. This is also consistent with the recommendation of the Airworthiness Directive Implementation Aviation Rulemaking Committee to increase flexibility in complying with ADs by identifying those actions in manufacturers’ service instructions that are ‘‘Required for Compliance’’ with ADs. We continue to work with manufacturers to implement this recommendation. But once we determine that an action is required, any deviation from the requirement must be approved as an alternative method of compliance. We also have decided not to include a generic reference to either the ‘‘delegated agent’’ or ‘‘design approval holder (DAH) with State of Design Authority design organization approval,’’ but instead we have provided the specific delegation approval granted by the State of Design Authority for the DAH throughout this proposed AD. Costs of Compliance We estimate that this proposed AD affects 83 airplanes of U.S. registry. The actions that are required by AD 2014–09–05, Amendment 39–17840 (79 FR 23909, April 29, 2014), and retained in this proposed AD take about 1 workhour per product, at an average labor rate of $85 per work-hour. Required parts cost $0 per product. Based on these figures, the estimated cost of the actions that are required by AD 2014– 09–05 is $85 per product. We also estimate that it would take about 1 work-hour per product to VerDate Mar<15>2010 16:42 Aug 25, 2014 Jkt 232001 comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Based on these figures, we estimate the cost of this proposed AD on U.S. operators to be $7,055, or $85 per product. In addition, we estimate that any necessary follow-on actions would take about 4 work-hours and require parts costing $7,530, for a cost of $7,870 per product. We have no way of determining the number of aircraft that might need these actions. Paperwork Reduction Act A federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB control number. The control number for the collection of information required by this AD is 2120–0056. The paperwork cost associated with this AD has been detailed in the Costs of Compliance section of this document and includes time for reviewing instructions, as well as completing and reviewing the collection of information. Therefore, all reporting associated with this AD is mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at 800 Independence Ave. SW., Washington, DC 20591, ATTN: Information Collection Clearance Officer, AES–200. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We determined that this proposed AD would not have federalism implications PO 00000 Frm 00010 Fmt 4702 Sfmt 4702 50865 under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); 3. Will not affect intrastate aviation in Alaska; and 4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. Amend § 39.13 by removing Airworthiness Directive (AD) 2014–09– 05, Amendment 39–17840 (79 FR 23909, April 29, 2014), and adding the following new AD: ■ Airbus: Docket No. FAA–2014–0584; Directorate Identifier 2014–NM–092–AD. (a) Comments Due Date We must receive comments by October 10, 2014. (b) Affected ADs This AD replaces AD 2014–09–05, Amendment 39–17840 (79 FR 23909, April 29, 2014). (c) Applicability This AD applies to the airplanes identified in paragraphs (c)(1) and (c)(2) of this AD, certificated in any category. (1) Airbus Model A330–201, A330–202, A330–203, A330–223, A330–243, A330–301, A330–302, A330–303, A330–321, A330–322, A330–323, A330–341, A330–342, and A330– 343 airplanes, all manufacturer serial numbers (MSNs), equipped with basic (201252 series) main landing gear (MLG), or growth (201490 series) MLG. E:\FR\FM\26AUP1.SGM 26AUP1 50866 Federal Register / Vol. 79, No. 165 / Tuesday, August 26, 2014 / Proposed Rules (2) Airbus Model A340–211, A340–212, A340–213, A340–311, A340–312, and A340– 313 airplanes, all MSNs, equipped with basic (201252 series) MLG or growth (201490 series) MLG. (d) Subject Air Transport Association (ATA) of America Code 32, Landing Gear. (e) Reason This AD was prompted by a report of a sidestay upper cardan pin of the MLG migrating out of position. We are issuing this AD to detect and correct migration of the sidestay upper cardan pin, which could result in disconnection of the sidestay upper arm from the airplane structure, and which could result in a landing gear collapse and consequent damage to the airplane and injury to occupants. tkelley on DSK3SPTVN1PROD with PROPOSALS (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Retained Repetitive Detailed Inspections With No Changes This paragraph restates the requirements of paragraph (g) of AD 2014–09–05, Amendment 39–17840 (79 FR 23909, April 29, 2014), with no changes. (1) For airplanes identified in paragraphs (g)(1)(i) and (g)(1)(ii) of this AD on which the affected MLG has exceeded 8 years since first overhaul, as of May 14, 2014 (the effective date of AD 2014–09–05, Amendment 39– 17840 (79 FR 23909, April 29, 2014), except those MLG that have had a second overhaul: Within 30 days after May 14, 2014, accomplish a detailed inspection for visible chrome of each affected MLG sidestay upper cardan pin, and associated nut and retainer assembly, in accordance with the instructions of Airbus Alert Operators Transmission (AOT) A32L003–14, dated March 10, 2014, including Appendices 1, 2, and 3 (the issue date is not specified on the appendices). (i) Airplanes equipped with any MLG sidestay upper cardan pin subassembly part number (P/N) 201267202 (on 201252 series MLG). (ii) Airplanes equipped with any MLG sidestay upper cardan pin subassembly P/N 201483202 (on 201490 series MLG). (2) If, during any inspection required by paragraph (g)(1) of this AD, no pin chrome is visible inboard of the wing rear spar fitting lug, repeat the detailed inspection for visible chrome specified in paragraph (g)(1) of this AD thereafter at intervals not to exceed 10 days. (3) If, during any inspection required by paragraphs (g)(1) or (g)(2) of this AD, pin chrome is visible inboard of the wing rear spar fitting lug, before further flight, replace the affected cardan pin assembly, in accordance with the instructions of Airbus AOT A32L003–14, dated March 10, 2014, including Appendices 1, 2, and 3 (the issue date is not specified on the appendices). Replacement of the affected cardan pin assembly terminates the repetitive inspections required by paragraph (g)(2) of this AD. VerDate Mar<15>2010 16:42 Aug 25, 2014 Jkt 232001 Note 1 to paragraph (g) of this AD: MLG sidestay upper cardan pin subassembly P/N 201267202 (found in Airbus Illustrated Parts Catalogue (IPC) as item 32–11–18–01) includes the cardan pin P/N 201267600. MLG sidestay upper cardan pin subassembly P/N 201483202 (found in Airbus IPC as item 32–11–18–01) includes the cardan pin P/N 201483600. (h) New Terminating Action—Gap Check Within 4 months after the effective date of this AD: Measure the cardan pin clearance dimensions (gap check) and do the applicable corrective action specified in paragraph (h)(1) or (h)(2) of this AD. Measuring the gap check and doing the applicable corrective action specified in paragraph (h)(1) or (h)(2) of this AD, as applicable, terminates the repetitive inspections required by paragraphs (g)(1) and (g)(2) of this AD for that sidestay upper cardan pin, nut, and retainer only. The measurement must be done in accordance with Airbus AOT A32L003–14, dated March 10, 2014, including Appendices 1, 2, and 3 (the issue date is not specified on the appendices). (1) If the total clearance dimension (gap check result) is equal to or greater than 1.5 mm, before further flight, replace the cardan pin assembly, in accordance with Airbus AOT A32L003–14, dated March 10, 2014, including Appendices 1, 2, and 3 (the issue date is not specified on the appendices). (2) If the total clearance dimension (gap check) is less than 1.5 mm but greater than 0.6 mm, do the actions specified in paragraphs (h)(2)(i) and (h)(2)(ii) of this AD. (i) Before further flight, send the information (Appendix 2 proforma, photographs, and the movement traceability sheet) specified in paragraph 4.2.3, ‘‘Findings,’’ of Airbus AOT A32L003–14, dated March 10, 2014, including Appendices 1, 2, and 3, to Airbus at the address specified in Appendix 2 of Airbus AOT A32L003–14, dated March 10, 2014. (ii) Within 30 days after accomplishing the gap check, repair using a method approved by the Manager, International Branch, ANM– 116, Transport Airplane Directorate, FAA; or the European Aviation Safety Agency (EASA); or Airbus’s EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (i) New Reporting of Inspection Results For airplanes on which a gap check specified in paragraph (h) of this AD has been done: Except as required by paragraph (h)(2)(i) of this AD, at the applicable time specified in paragraphs (i)(1) and (i)(2) of this AD, report all findings (including no findings) to Airbus, in accordance with Airbus AOT A32L003–14, dated March 10, 2014, including Appendices 1, 2, and 3, (the issue date is not specified on the appendices). (1) If the gap check was done on or after the effective date of this AD: Submit the report within 30 days after the inspection. (2) If the gap check was done before the effective date of this AD: Submit the report within 30 days after the effective date of this AD. PO 00000 Frm 00011 Fmt 4702 Sfmt 4702 (j) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Vladimir Ulyanov, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; telephone 425–227–1138; fax 425–227–1149. Information may be emailed to: 9-ANM-116AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The AMOC approval letter must specifically reference this AD. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Branch, ANM– 116, Transport Airplane Directorate, FAA; or the European Aviation Safety Agency (EASA); or Airbus’s EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Reporting Requirements: A federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120–0056. Public reporting for this collection of information is estimated to be approximately 5 minutes per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave. SW., Washington, DC 20591, Attn: Information Collection Clearance Officer, AES–200. (k) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) European Aviation Safety Agency Airworthiness Directive 2014–0066 (Corrected March 20, 2014), for related information. This MCAI may be found in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA– 2014–0584. (2) For service information identified in this AD, contact Airbus SAS, Airworthiness Office—EAL, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone +33 E:\FR\FM\26AUP1.SGM 26AUP1 Federal Register / Vol. 79, No. 165 / Tuesday, August 26, 2014 / Proposed Rules 5 61 93 36 96; fax +33 5 61 93 45 80; email airworthiness.A330-A340@airbus.com; Internet https://www.airbus.com. You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Issued in Renton, Washington, on August 15, 2014. Jeffrey E. Duven, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2014–20262 Filed 8–25–14; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2014–0572; Directorate Identifier 2014–NM–027–AD] RIN 2120–AA64 Airworthiness Directives; The Boeing Company Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to supersede Airworthiness Directive (AD) 98–22–10, which applies to certain The Boeing Company Model 737–100, –200, –200C, and –300 series airplanes. AD 98–22–10 currently requires repetitive inspections for cracking of the aft frame and frame support structure of the forward service doorway, and repair if necessary. AD 98–22–10 also provides for an optional terminating action for the repetitive inspection requirements of that AD. Since we issued AD 98–22–10, we have determined that additional inspections are needed, and that additional airplanes may be subject to the identified unsafe condition. This proposed AD would add inspections and add airplanes to the applicability. For certain airplanes, this proposed AD provides a preventive modification, which would terminate the repetitive inspections. We are proposing this AD to detect and correct fatigue cracking of the aft frame and frame support structure of the forward service doorway around the six doorstop fittings, which could result in door deflection and loss of pressurization. DATES: We must receive comments on this proposed AD by October 10, 2014. ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: tkelley on DSK3SPTVN1PROD with PROPOSALS SUMMARY: VerDate Mar<15>2010 16:42 Aug 25, 2014 Jkt 232001 • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H–65, Seattle, WA 98124–2207; telephone 206–544–5000, extension 1; fax 206–766–5680; Internet https:// www.myboeingfleet.com. You may review this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2014– 0572; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (phone: 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Alan Pohl, Aerospace Engineer, Airframe Branch, ANM–120S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW., Renton, WA 98057–3356; phone 425–917–6450; fax 425–917–6590; email: alan.pohl@ faa.gov. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2014–0572; Directorate Identifier 2014–NM–027–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the PO 00000 Frm 00012 Fmt 4702 Sfmt 4702 50867 closing date and may amend this proposed AD because of those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion On October 19, 1998, we issued AD 98–22–10, Amendment 39–10858 (63 FR 57240, October 27, 1998), for certain The Boeing Company Model 737–100, –200, –200C, and –300 series airplanes. AD 98–22–10 requires repetitive inspections to detect cracking of the aft frame and aft frame support structure of the forward service doorway, and repair if necessary. AD 98–22–10 resulted from reports of fatigue cracking of the aft frame and frame support structure of the forward service doorway. We issued AD 98–22–10 to prevent fatigue cracking of the aft frame and frame support structure of the forward service doorway, which could result in loss of the door, and consequent rapid decompression of the fuselage. Tables 9 through 12 in paragraph 1.E., ‘‘Compliance,’’ of Boeing Alert Service Bulletin 737–53A1108, Revision 7, dated July 7, 2014, specify post-repair inspections, which may be used in support of compliance with section 121.1109(c)(2) or 129.109(b)(2) of the Federal Aviation Regulations (14 CFR 121.1109(c)(2) or 129.109(b)(2)). However, this NPRM does not propose to require those post-repair inspections. This difference has been coordinated with Boeing. Actions Since AD 98–22–10, Amendment 39–10858 (63 FR 57240, October 27, 1998), Was Issued Since we issued AD 98–22–10, Amendment 39–10858 (63 FR 57240, October 27, 1998), we received reports of cracking in the forward galley service doorway surround structure between body station (STA) 332.1 and STA 344, which are outside the inspection area of AD 98–22–10, and we have received reports that cracking has been discovered on airplanes outside the applicability of AD 98–22–10. We have determined that additional inspections are needed, and that additional airplanes are subject to the identified unsafe condition. Relevant Service Information We reviewed Boeing Alert Service Bulletin 737–53A1108, Revision 7, dated July 7, 2014. For information on the procedures and compliance times, E:\FR\FM\26AUP1.SGM 26AUP1

Agencies

[Federal Register Volume 79, Number 165 (Tuesday, August 26, 2014)]
[Proposed Rules]
[Pages 50863-50867]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2014-20262]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0584; Directorate Identifier 2014-NM-092-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to supersede Airworthiness Directive (AD) 2014-09-
05, for certain Airbus Model A330-200 and -300 series airplanes, and 
Model A340-200 and -300 series airplanes. AD 2014-09-05 currently 
requires repetitive inspections of certain sidestay upper cardan pins 
of the main landing gear (MLG), and associated nuts and retainer 
assemblies, and pin replacement if necessary. Since we issued AD 2014-
09-05, we have determined that a previously optional measurement is 
necessary to address the identified unsafe condition. We are proposing 
this AD to detect and correct migration of the sidestay upper cardan 
pin, which could result in disconnection of the sidestay upper arm from 
the airplane structure, and could result in a landing gear collapse and 
consequent damage to the airplane and injury to occupants.

DATES: We must receive comments on this proposed AD by October 10, 
2014.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Airbus SAS--Airworthiness Office--EAL, 1 Rond Point Maurice Bellonte, 
31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 
93 45 80; email airworthiness.A330-A340@airbus.com; Internet https://www.airbus.com. You may view this referenced service information at the 
FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. 
For information on the availability of this material at the FAA, call 
425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0584; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday,

[[Page 50864]]

except Federal holidays. The AD docket contains this proposed AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone 800-647-
5527) is in the ADDRESSES section. Comments will be available in the AD 
docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1138; 
fax 425-227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2014-0584; 
Directorate Identifier 2014-NM-092-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    On April 16, 2014, we issued AD 2014-09-05, Amendment 39-17840 (79 
FR 23909, April 29, 2014). AD 2014-09-05 requires actions intended to 
address an unsafe condition on certain Airbus Model A330-200 and -300 
series airplanes, and Model A340-200 and -300 series airplanes.
    Since we issued AD 2014-09-05, Amendment 39-17840 (79 FR 23909, 
April 29, 2014), we have determined that the optional measurement 
specified in that AD is necessary to address the identified unsafe 
condition.
    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
Airworthiness Directive 2014-0066, corrected March 20, 2014 (referred 
to after this as the Mandatory Continuing Airworthiness Information, or 
``the MCAI''), to correct an unsafe condition on certain Airbus Model 
A330-200 and -300 series airplanes, and Model A340-200 and -300 series 
airplanes. The MCAI states:

    An A330 aeroplane equipped with Basic (main landing gear) MLG 
was rolling out after landing when it experienced a nose wheel 
steering fault (unrelated to the safety subject addressed by this 
[EASA] AD), which resulted in the crew stopping the aeroplane on the 
taxiway after vacating the runway.
    The subsequent investigation revealed that the right-hand MLG 
sidestay upper cardan pin had migrated out of position. The sidestay 
upper cardan nut and retainer were found in the landing gear bay 
detached from the upper cardan pin. The nut and the retainer were 
still bolted together.
    This condition, if not detected and corrected, could lead to a 
complete migration of the sidestay upper cardan pin and a 
disconnection of the sidestay upper arm from the aeroplane 
structure, possibly resulting in MLG collapse with consequent damage 
to the aeroplane and injury to occupants.
    To address this potential condition, Airbus published Alert 
Operators Transmission (AOT) A32L003-14, providing inspection 
instructions.
    For the reasons described above, this [EASA] AD requires 
accomplishment of repetitive [detailed inspections for visible 
chrome] of the MLG upper cardan pin, nut and retainer [and pin 
replacement if necessary]. This [EASA] AD also requires 
accomplishment of a gap check between wing rear spar fitting lugs 
and the bush flanges [and corrective actions if necessary. 
Corrective actions include repair or replacement of the cardan pin 
assembly].

You may examine the MCAI in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0584.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

``Contacting the Manufacturer'' Paragraph in This Proposed AD

    Since late 2006, we have included a standard paragraph titled 
``Airworthy Product'' in all MCAI ADs in which the FAA develops an AD 
based on a foreign authority's AD.
    The MCAI or referenced service information in an FAA AD often 
directs the owner/operator to contact the manufacturer for corrective 
actions, such as a repair. Briefly, the Airworthy Product paragraph 
allowed owners/operators to use corrective actions provided by the 
manufacturer if those actions were FAA-approved. In addition, the 
paragraph stated that any actions approved by the State of Design 
Authority (or its delegated agent) are considered to be FAA-approved.
    In an NPRM having Directorate Identifier 2012-NM-101-AD (78 FR 
78285, December 26, 2013), we proposed to prevent the use of repairs 
that were not specifically developed to correct the unsafe condition, 
by requiring that the repair approval provided by the State of Design 
Authority or its delegated agent specifically refer to the FAA AD. This 
change was intended to clarify the method of compliance and to provide 
operators with better visibility of repairs that are specifically 
developed and approved to correct the unsafe condition. In addition, we 
proposed to change the phrase ``its delegated agent'' to include a 
design approval holder (DAH) with State of Design Authority design 
organization approval (DOA), as applicable, to refer to a DAH 
authorized to approve required repairs for the proposed AD.
    One commenter to the NPRM having Directorate Identifier 2012-NM-
101-AD (78 FR 78285, December 26, 2013) stated the following: ``The 
proposed wording, being specific to repairs, eliminates the 
interpretation that Airbus messages are acceptable for approving minor 
deviations (corrective actions) needed during accomplishment of an AD 
mandated Airbus service bulletin.''
    This comment has made the FAA aware that some operators have 
misunderstood or misinterpreted the Airworthy Product paragraph to 
allow the owner/operator to use messages provided by the manufacturer 
as approval of deviations during the accomplishment of an AD-mandated 
action. The Airworthy Product paragraph does not approve messages or 
other information provided by the manufacturer for deviations to the 
requirements of the AD-mandated actions. The Airworthy Product 
paragraph only addresses the requirement to contact the manufacturer 
for corrective actions for the identified unsafe condition and does not 
cover deviations from other AD requirements. However, deviations to AD-
required actions are addressed in 14 CFR 39.17, and anyone may request 
the approval for an alternative method of compliance to the AD-required 
actions using the procedures found in 14 CFR 39.19.
    To address this misunderstanding and misinterpretation of the 
Airworthy Product paragraph, we have changed the paragraph and retitled 
it ``Contacting the

[[Page 50865]]

Manufacturer.'' This paragraph now clarifies that for any requirement 
in this proposed AD to obtain corrective actions from a manufacturer, 
the actions must be accomplished using a method approved by the FAA, 
the European Aviation Safety Agency (EASA), or Airbus's EASA DOA.
    The Contacting the Manufacturer paragraph also clarifies that, if 
approved by the DOA, the approval must include the DOA-authorized 
signature. The DOA signature indicates that the data and information 
contained in the document are EASA-approved, which is also FAA-
approved. Messages and other information provided by the manufacturer 
that do not contain the DOA-authorized signature approval are not EASA-
approved, unless EASA directly approves the manufacturer's message or 
other information.
    This clarification does not remove flexibility previously afforded 
by the Airworthy Product paragraph. Consistent with long-standing FAA 
policy, such flexibility was never intended for required actions. This 
is also consistent with the recommendation of the Airworthiness 
Directive Implementation Aviation Rulemaking Committee to increase 
flexibility in complying with ADs by identifying those actions in 
manufacturers' service instructions that are ``Required for 
Compliance'' with ADs. We continue to work with manufacturers to 
implement this recommendation. But once we determine that an action is 
required, any deviation from the requirement must be approved as an 
alternative method of compliance.
    We also have decided not to include a generic reference to either 
the ``delegated agent'' or ``design approval holder (DAH) with State of 
Design Authority design organization approval,'' but instead we have 
provided the specific delegation approval granted by the State of 
Design Authority for the DAH throughout this proposed AD.

Costs of Compliance

    We estimate that this proposed AD affects 83 airplanes of U.S. 
registry.
    The actions that are required by AD 2014-09-05, Amendment 39-17840 
(79 FR 23909, April 29, 2014), and retained in this proposed AD take 
about 1 work-hour per product, at an average labor rate of $85 per 
work-hour. Required parts cost $0 per product. Based on these figures, 
the estimated cost of the actions that are required by AD 2014-09-05 is 
$85 per product.
    We also estimate that it would take about 1 work-hour per product 
to comply with the basic requirements of this proposed AD. The average 
labor rate is $85 per work-hour. Based on these figures, we estimate 
the cost of this proposed AD on U.S. operators to be $7,055, or $85 per 
product.
    In addition, we estimate that any necessary follow-on actions would 
take about 4 work-hours and require parts costing $7,530, for a cost of 
$7,870 per product. We have no way of determining the number of 
aircraft that might need these actions.

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB control number. The control 
number for the collection of information required by this AD is 2120-
0056. The paperwork cost associated with this AD has been detailed in 
the Costs of Compliance section of this document and includes time for 
reviewing instructions, as well as completing and reviewing the 
collection of information. Therefore, all reporting associated with 
this AD is mandatory. Comments concerning the accuracy of this burden 
and suggestions for reducing the burden should be directed to the FAA 
at 800 Independence Ave. SW., Washington, DC 20591, ATTN: Information 
Collection Clearance Officer, AES-200.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. Amend Sec.  39.13 by removing Airworthiness Directive (AD) 2014-09-
05, Amendment 39-17840 (79 FR 23909, April 29, 2014), and adding the 
following new AD:

Airbus: Docket No. FAA-2014-0584; Directorate Identifier 2014-NM-
092-AD.

(a) Comments Due Date

    We must receive comments by October 10, 2014.

(b) Affected ADs

    This AD replaces AD 2014-09-05, Amendment 39-17840 (79 FR 23909, 
April 29, 2014).

(c) Applicability

    This AD applies to the airplanes identified in paragraphs (c)(1) 
and (c)(2) of this AD, certificated in any category.
    (1) Airbus Model A330-201, A330-202, A330-203, A330-223, A330-
243, A330-301, A330-302, A330-303, A330-321, A330-322, A330-323, 
A330-341, A330-342, and A330-343 airplanes, all manufacturer serial 
numbers (MSNs), equipped with basic (201252 series) main landing 
gear (MLG), or growth (201490 series) MLG.

[[Page 50866]]

    (2) Airbus Model A340-211, A340-212, A340-213, A340-311, A340-
312, and A340-313 airplanes, all MSNs, equipped with basic (201252 
series) MLG or growth (201490 series) MLG.

(d) Subject

    Air Transport Association (ATA) of America Code 32, Landing 
Gear.

(e) Reason

    This AD was prompted by a report of a sidestay upper cardan pin 
of the MLG migrating out of position. We are issuing this AD to 
detect and correct migration of the sidestay upper cardan pin, which 
could result in disconnection of the sidestay upper arm from the 
airplane structure, and which could result in a landing gear 
collapse and consequent damage to the airplane and injury to 
occupants.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Repetitive Detailed Inspections With No Changes

    This paragraph restates the requirements of paragraph (g) of AD 
2014-09-05, Amendment 39-17840 (79 FR 23909, April 29, 2014), with 
no changes.
    (1) For airplanes identified in paragraphs (g)(1)(i) and 
(g)(1)(ii) of this AD on which the affected MLG has exceeded 8 years 
since first overhaul, as of May 14, 2014 (the effective date of AD 
2014-09-05, Amendment 39-17840 (79 FR 23909, April 29, 2014), except 
those MLG that have had a second overhaul: Within 30 days after May 
14, 2014, accomplish a detailed inspection for visible chrome of 
each affected MLG sidestay upper cardan pin, and associated nut and 
retainer assembly, in accordance with the instructions of Airbus 
Alert Operators Transmission (AOT) A32L003-14, dated March 10, 2014, 
including Appendices 1, 2, and 3 (the issue date is not specified on 
the appendices).
    (i) Airplanes equipped with any MLG sidestay upper cardan pin 
subassembly part number (P/N) 201267202 (on 201252 series MLG).
    (ii) Airplanes equipped with any MLG sidestay upper cardan pin 
subassembly P/N 201483202 (on 201490 series MLG).
    (2) If, during any inspection required by paragraph (g)(1) of 
this AD, no pin chrome is visible inboard of the wing rear spar 
fitting lug, repeat the detailed inspection for visible chrome 
specified in paragraph (g)(1) of this AD thereafter at intervals not 
to exceed 10 days.
    (3) If, during any inspection required by paragraphs (g)(1) or 
(g)(2) of this AD, pin chrome is visible inboard of the wing rear 
spar fitting lug, before further flight, replace the affected cardan 
pin assembly, in accordance with the instructions of Airbus AOT 
A32L003-14, dated March 10, 2014, including Appendices 1, 2, and 3 
(the issue date is not specified on the appendices). Replacement of 
the affected cardan pin assembly terminates the repetitive 
inspections required by paragraph (g)(2) of this AD.
    Note 1 to paragraph (g) of this AD: MLG sidestay upper cardan 
pin subassembly P/N 201267202 (found in Airbus Illustrated Parts 
Catalogue (IPC) as item 32-11-18-01) includes the cardan pin P/N 
201267600. MLG sidestay upper cardan pin subassembly P/N 201483202 
(found in Airbus IPC as item 32-11-18-01) includes the cardan pin P/
N 201483600.

(h) New Terminating Action--Gap Check

    Within 4 months after the effective date of this AD: Measure the 
cardan pin clearance dimensions (gap check) and do the applicable 
corrective action specified in paragraph (h)(1) or (h)(2) of this 
AD. Measuring the gap check and doing the applicable corrective 
action specified in paragraph (h)(1) or (h)(2) of this AD, as 
applicable, terminates the repetitive inspections required by 
paragraphs (g)(1) and (g)(2) of this AD for that sidestay upper 
cardan pin, nut, and retainer only. The measurement must be done in 
accordance with Airbus AOT A32L003-14, dated March 10, 2014, 
including Appendices 1, 2, and 3 (the issue date is not specified on 
the appendices).
    (1) If the total clearance dimension (gap check result) is equal 
to or greater than 1.5 mm, before further flight, replace the cardan 
pin assembly, in accordance with Airbus AOT A32L003-14, dated March 
10, 2014, including Appendices 1, 2, and 3 (the issue date is not 
specified on the appendices).
    (2) If the total clearance dimension (gap check) is less than 
1.5 mm but greater than 0.6 mm, do the actions specified in 
paragraphs (h)(2)(i) and (h)(2)(ii) of this AD.
    (i) Before further flight, send the information (Appendix 2 
proforma, photographs, and the movement traceability sheet) 
specified in paragraph 4.2.3, ``Findings,'' of Airbus AOT A32L003-
14, dated March 10, 2014, including Appendices 1, 2, and 3, to 
Airbus at the address specified in Appendix 2 of Airbus AOT A32L003-
14, dated March 10, 2014.
    (ii) Within 30 days after accomplishing the gap check, repair 
using a method approved by the Manager, International Branch, ANM-
116, Transport Airplane Directorate, FAA; or the European Aviation 
Safety Agency (EASA); or Airbus's EASA Design Organization Approval 
(DOA). If approved by the DOA, the approval must include the DOA-
authorized signature.

(i) New Reporting of Inspection Results

    For airplanes on which a gap check specified in paragraph (h) of 
this AD has been done: Except as required by paragraph (h)(2)(i) of 
this AD, at the applicable time specified in paragraphs (i)(1) and 
(i)(2) of this AD, report all findings (including no findings) to 
Airbus, in accordance with Airbus AOT A32L003-14, dated March 10, 
2014, including Appendices 1, 2, and 3, (the issue date is not 
specified on the appendices).
    (1) If the gap check was done on or after the effective date of 
this AD: Submit the report within 30 days after the inspection.
    (2) If the gap check was done before the effective date of this 
AD: Submit the report within 30 days after the effective date of 
this AD.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to ATTN: Vladimir 
Ulyanov, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, 
WA 98057-3356; telephone 425-227-1138; fax 425-227-1149. Information 
may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office. The 
AMOC approval letter must specifically reference this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, International 
Branch, ANM-116, Transport Airplane Directorate, FAA; or the 
European Aviation Safety Agency (EASA); or Airbus's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.
    (3) Reporting Requirements: A federal agency may not conduct or 
sponsor, and a person is not required to respond to, nor shall a 
person be subject to a penalty for failure to comply with a 
collection of information subject to the requirements of the 
Paperwork Reduction Act unless that collection of information 
displays a current valid OMB Control Number. The OMB Control Number 
for this information collection is 2120-0056. Public reporting for 
this collection of information is estimated to be approximately 5 
minutes per response, including the time for reviewing instructions, 
completing and reviewing the collection of information. All 
responses to this collection of information are mandatory. Comments 
concerning the accuracy of this burden and suggestions for reducing 
the burden should be directed to the FAA at: 800 Independence Ave. 
SW., Washington, DC 20591, Attn: Information Collection Clearance 
Officer, AES-200.

(k) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) European Aviation Safety Agency Airworthiness Directive 2014-
0066 (Corrected March 20, 2014), for related information. This MCAI 
may be found in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2014-0584.
    (2) For service information identified in this AD, contact 
Airbus SAS, Airworthiness Office--EAL, 1 Rond Point Maurice 
Bellonte, 31707 Blagnac Cedex, France; telephone +33

[[Page 50867]]

5 61 93 36 96; fax +33 5 61 93 45 80; email airworthiness.A330-A340@airbus.com; Internet https://www.airbus.com. You may view this 
service information at the FAA, Transport Airplane Directorate, 1601 
Lind Avenue SW., Renton, WA. For information on the availability of 
this material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on August 15, 2014.
Jeffrey E. Duven,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-20262 Filed 8-25-14; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.