Airworthiness Directives; ATR-GIE Avions de Transport Régional Airplanes, 47390-47393 [2014-19158]

Download as PDF 47390 Federal Register / Vol. 79, No. 156 / Wednesday, August 13, 2014 / Proposed Rules wreier-aviles on DSK5TPTVN1PROD with PROPOSALS (h) Inspection If a rudder assembly having any part number starting with A55471500 or A55471500XXX (where XXX stands for any numerical value) is found during the inspection required by paragraph (g) of this AD, and has been inspected before the effective date of this AD, as specified in Airbus Service Bulletin A300–55–3038, dated November 7, 2007; or Airbus Service Bulletin A310–55–4034, dated November 7, 2007; as applicable; and has been removed and installed on any airplane after the inspection, or that rudder has been inspected off-wing: Before further flight, do an ultrasonic test inspection for damage (e.g., disbonding and liquid ingress) of the rudder side panel along the Z-profile and in the booster area, in accordance with Airbus AOT A55L001–12, dated December 20, 2012. If any damage is found, before further flight, do the inspections specified in paragraphs (h)(1) and (h)(2) of this AD to confirm disbonding damage, in accordance with AOT A55L001– 12, dated December 20, 2012. (1) Do an elasticity of laminate checker inspection to detect external and internal disbonding. (2) Do a woodpecker or tap test inspection to detect external disbonding. (i) Repair If any disbonding or damage (e.g. liquid ingress) is confirmed during any inspection required by paragraphs (h), (h)(1), and (h)(2) of this AD, repair at the time specified in paragraph (i)(1), (i)(2), or (i)(3) of this AD, as applicable. (1) If the disbonding is less than or equal to 50 millimeters (mm) in width and less than or equal to 150 mm in length: Before further flight, vent the rudder core using a method approved by the Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA; or EASA; or Airbus’s EASA DOA. Within 100 flight cycles after venting the rudder core, do a permanent repair using a method approved by the Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA; or EASA; or Airbus’s EASA DOA. If approved by the DOA, the approval for the venting and repair methods must include the DOAauthorized signature. (2) If the disbonding is greater than 50mm in width, or greater than 150 mm in length: Before further flight, repair using a method approved by the Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA; or EASA; or Airbus’s EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature. (3) If any damage other than disbonding (e.g., liquid ingress) is confirmed during any inspection required by paragraph (h) of this AD, before further flight, repair, using a method approved by the Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA; or EASA; or Airbus’s EASA DOA. If approved by the DOA, the approval must include the DOAauthorized signature. (j) Parts Installation Limitation As of the effective date of this AD, you may install, on any airplane, a rudder assembly VerDate Mar<15>2010 15:24 Aug 12, 2014 Jkt 232001 having part number A55471500XXX (where XXX stands for any numerical value), provided the inspection required by paragraph (h) of this AD and all applicable repair actions required by paragraph (i) of this AD are done before further flight. The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM–116, Tranport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Vladimir Ulyanov, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; telephone (425) 227–1138; fax (425) 227– 1149. Information may be emailed to: 9ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. The AMOC approval letter must specifically reference this AD. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Branch, ANM– 116, Transport Airplane Directorate, FAA; or EASA; or Airbus’s EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature. (l) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA Airworthiness Directive 2013–0270R1, dated November 27, 2013, for related information. This MCAI may be found in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2014–0525. (2) For service information identified in this AD, contact Airbus SAS, Airworthiness Office—EAL, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 45 80; email airworthiness.A330-A340@airbus.com; Internet https://www.airbus.com. You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Issued in Renton, Washington, on July 30, 2014. Jeffrey E. Duven, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2014–19155 Filed 8–12–14; 8:45 am] PO 00000 Frm 00008 Fmt 4702 Sfmt 4702 Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2014–0530; Directorate Identifier 2014–NM–062–AD] (k) Other FAA AD Provisions BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION RIN 2120–AA64 Airworthiness Directives; ATR—GIE ´ Avions de Transport Regional Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for certain ATR—GIE Avions de Transport ´ Regional Model ATR42–500 airplanes, and Model ATR72–212A airplanes. This proposed AD was prompted by a report that during an inspection of an airplane on the production line, interference was detected between the electrical harness and a bonding lead due to an incorrect installation of the affected bonding lead. This proposed AD would require a detailed inspection for damage or incorrect routing of the bonding lead routing above the 120VU shelf, and if any damage or incorrect routing is found, modifying the bonding lead routing. We are proposing this AD to detect and correct installation of the bonding lead, which could cause arcing and chafing, and could possibly result in an uncontrolled fire. DATES: We must receive comments on this proposed AD by September 29, 2014. SUMMARY: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact ATR—GIE ´ ´ Avions de Transport Regional, 1, Allee Pierre Nadot, 31712 Blagnac Cedex, France; telephone +33 (0) 5 62 21 62 21; ADDRESSES: E:\FR\FM\13AUP1.SGM 13AUP1 Federal Register / Vol. 79, No. 156 / Wednesday, August 13, 2014 / Proposed Rules fax +33 (0) 5 62 21 67 18; email continued.airworthiness@atr.fr; Internet https://www.aerochain.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2014– 0530; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; telephone 425–227–1137; fax 425–227–1149. SUPPLEMENTARY INFORMATION: wreier-aviles on DSK5TPTVN1PROD with PROPOSALS Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2014–0530; Directorate Identifier 2014–NM–062–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued Airworthiness Directive 2014–0056, dated March 7, 2014 (referred to after this as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition for certain ATR— VerDate Mar<15>2010 15:24 Aug 12, 2014 Jkt 232001 ´ GIE Avions de Transport Regional Model ATR42–500 airplanes, and Model ATR72–212A airplanes. The MCAI states: During inspection of an aeroplane on the production line, interference was detected between electrical harnesses (2M–2S–6M) and a bonding lead, located in zone 214, positioned above and forward of the 120VU shelf. Subsequent investigation revealed that the interference was a result of an incorrect installation of the affected bonding lead. This condition, if not detected and corrected, could lead to arcing and chafing, possibly resulting in an uncontrolled fire. To address this potential unsafe condition, ATR issued Service Bulletin (SB) ATR42–92– 0025 and SB ATR72–92–1034, as applicable to aeroplane model, to provide inspection instructions. For the reasons described above, this [EASA] AD requires a one-time [detailed] inspection [for damage or incorrect routing of the bonding lead routing above the 120VU shelf] of the electrical harness 2M–2S–6M in zone 214 and, depending on findings, accomplishment of corrective action(s). You may examine the MCAI in the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2014– 0530. Relevant Service Information ATR—GIE Avions de Transport ´ Regional has issued ATR Service Bulletin ATR42–92–0025, dated November 7, 2013; and ATR Service Bulletin ATR72–92–1034, dated November 7, 2013. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI. FAA’s Determination and Requirements of This Proposed AD This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of these same type designs. ‘‘Contacting the Manufacturer’’ Paragraph in This Proposed AD Since late 2006, we have included a standard paragraph titled ‘‘Airworthy Product’’ in all MCAI ADs in which the FAA develops an AD based on a foreign authority’s AD. The MCAI or referenced service information in an FAA AD often directs PO 00000 Frm 00009 Fmt 4702 Sfmt 4702 47391 the owner/operator to contact the manufacturer for corrective actions, such as a repair. Briefly, the Airworthy Product paragraph allowed owners/ operators to use corrective actions provided by the manufacturer if those actions were FAA-approved. In addition, the paragraph stated that any actions approved by the State of Design Authority (or its delegated agent) are considered to be FAA-approved. In an NPRM having Directorate Identifier 2012–NM–101–AD (78 FR 78285, December 26, 2013), we proposed to prevent the use of repairs that were not specifically developed to correct the unsafe condition, by requiring that the repair approval provided by the State of Design Authority or its delegated agent specifically refer to the FAA AD. This change was intended to clarify the method of compliance and to provide operators with better visibility of repairs that are specifically developed and approved to correct the unsafe condition. In addition, we proposed to change the phrase ‘‘its delegated agent’’ to include a design approval holder (DAH) with State of Design Authority design organization approval (DOA), as applicable, to refer to a DAH authorized to approve required repairs for the proposed AD. One commenter to the NPRM having Directorate Identifier 2012–NM–101–AD (78 FR 78285, December 26, 2013) stated the following: ‘‘The proposed wording, being specific to repairs, eliminates the interpretation that Airbus messages are acceptable for approving minor deviations (corrective actions) needed during accomplishment of an AD mandated Airbus service bulletin.’’ This comment has made the FAA aware that some operators have misunderstood or misinterpreted the Airworthy Product paragraph to allow the owner/operator to use messages provided by the manufacturer as approval of deviations during the accomplishment of an AD-mandated action. The Airworthy Product paragraph does not approve messages or other information provided by the manufacturer for deviations to the requirements of the AD-mandated actions. The Airworthy Product paragraph only addresses the requirement to contact the manufacturer for corrective actions for the identified unsafe condition and does not cover deviations from other AD requirements. However, deviations to AD-required actions are addressed in 14 CFR 39.17, and anyone may request the approval for an alternative method of compliance to the AD-required actions using the procedures found in 14 CFR 39.19. E:\FR\FM\13AUP1.SGM 13AUP1 47392 Federal Register / Vol. 79, No. 156 / Wednesday, August 13, 2014 / Proposed Rules wreier-aviles on DSK5TPTVN1PROD with PROPOSALS To address this misunderstanding and misinterpretation of the Airworthy Product paragraph, we have changed the paragraph and retitled it ‘‘Contacting the Manufacturer.’’ This paragraph now clarifies that for any requirement in this proposed AD to obtain corrective actions from a manufacturer, the actions must be accomplished using a method approved by the FAA, the European Aviation Safety Agency (EASA), or ATR—GIE Avions de Transport ´ Regional’s EASA DOA. The Contacting the Manufacturer paragraph also clarifies that, if approved by the DOA, the approval must include the DOA-authorized signature. The DOA signature indicates that the data and information contained in the document are EASA-approved, which is also FAAapproved. Messages and other information provided by the manufacturer that do not contain the DOA-authorized signature approval are not EASA-approved, unless EASA directly approves the manufacturer’s message or other information. This clarification does not remove flexibility previously afforded by the Airworthy Product paragraph. Consistent with long-standing FAA policy, such flexibility was never intended for required actions. This is also consistent with the recommendation of the Airworthiness Directive Implementation Aviation Rulemaking Committee to increase flexibility in complying with ADs by identifying those actions in manufacturers’ service instructions that are ‘‘Required for Compliance’’ with ADs. We continue to work with manufacturers to implement this recommendation. But once we determine that an action is required, any deviation from the requirement must be approved as an alternative method of compliance. Costs of Compliance We estimate that this proposed AD affects 5 airplanes of U.S. registry. We also estimate that it would take about 2 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Required parts would cost about $0 per product. Based on these figures, we estimate the cost of this proposed AD on U.S. operators to be $850, or $170 per product. In addition, we estimate that any necessary follow-on actions would take about 2 work-hours and require parts costing $0, for a cost of $170 per product. We have no way of determining the number of aircraft that might need this action. VerDate Mar<15>2010 15:24 Aug 12, 2014 Jkt 232001 Authority for this Rulemaking § 39.13 Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. ■ Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); 3. Will not affect intrastate aviation in Alaska; and 4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. PO 00000 Frm 00010 Fmt 4702 Sfmt 4702 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ´ ATR—GIE Avions de Transport Regional: Docket No. FAA–2014–0530; Directorate Identifier 2014–NM–062–AD. (a) Comments Due Date We must receive comments by September 29, 2014. (b) Affected ADs None. (c) Applicability This AD applies to ATR—GIE Avions de ´ Transport Regional airplanes, certificated in any category, as identified in paragraph (c)(1) and (c)(2) of this AD. (1) Model ATR42–500 airplanes, manufacturer serial numbers 669 through 1005 inclusive. (2) Model ATR72–212A airplanes, manufacturer serial numbers 773, 774, 776 through 1094 inclusive, 1096 through 1099 inclusive, and 1101. (d) Subject Air Transport Association (ATA) of America Code 92, Electrical Routing. (e) Reason This AD was prompted by a report that during an inspection of an airplane on the production line, interference was detected between the electrical harness and a bonding lead due to an incorrect installation of the affected bonding lead. We are issuing this AD to detect and correct installation of the bonding lead, which could cause arcing and chafing, and could possibly result in an uncontrolled fire. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Inspection Within 1,000 flight hours after the effective date of this AD: Do a detailed inspection of the bonding lead routing above the 120VU shelf for damage (i.e., wire chaffing, evidence of burning) or incorrect routing, in accordance with the Accomplishment Instructions of ATR Service Bulletin ATR42– 92–0025, dated November 7, 2013 (for Model ATR42–500 airplanes); or ATR Service Bulletin ATR72–92–1034, dated November 7, 2013 (for Model ATR72–212A airplanes). (h) Corrective Action If, during the inspection required by paragraph (g) of this AD, any damage (i.e., wire chaffing, evidence of burning) or incorrect routing is found: Before further flight, modify the bonding lead routing above the 120VU shelf, in accordance with the Accomplishment Instructions of ATR Service Bulletin ATR42–92–0025, dated November 7, 2013 (for Model ATR42–500 airplanes); or ATR Service Bulletin ATR72–92–1034, dated November 7, 2013 (for Model ATR72–212A airplanes). E:\FR\FM\13AUP1.SGM 13AUP1 Federal Register / Vol. 79, No. 156 / Wednesday, August 13, 2014 / Proposed Rules (i) Other FAA AD Provisions DEPARTMENT OF TRANSPORTATION The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; telephone 425–227–1137; fax 425–227–1149. Information may be emailed to: 9-ANM-116AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The AMOC approval letter must specifically reference this AD. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Branch, ANM– 116, Transport Airplane Directorate, FAA; or the European Aviation Safety Agency (EASA); or ATR—GIE Avions de Transport ´ Regional’s EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOAauthorized signature. wreier-aviles on DSK5TPTVN1PROD with PROPOSALS (j) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) European Aviation Safety Agency Airworthiness Directive 2014–0056, dated March 7, 2014, for related information. This MCAI may be found in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2014–0530. (2) For service information identified in this AD, contact ATR—GIE Avions de ´ ´ Transport Regional, 1, Allee Pierre Nadot, 31712 Blagnac Cedex, France; telephone +33 (0) 5 62 21 62 21; fax +33 (0) 5 62 21 67 18; email continued.airworthiness@atr.fr; Internet https://www.aerochain.com. You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Issued in Renton, Washington, on August 1, 2014. Jeffrey E. Duven, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2014–19158 Filed 8–12–14; 8:45 am] BILLING CODE 4910–13–P VerDate Mar<15>2010 15:24 Aug 12, 2014 Jkt 232001 Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2014–0528; Directorate Identifier 2014–NM–060–AD] RIN 2120–AA64 Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for certain Bombardier Inc. Model DHC–8–400 series airplanes. This proposed AD was prompted by a report that during production, an incorrect clevis was used, resulting in improper installation onto the alternate release cable of the main landing gear (MLG). This proposed AD would require a detailed visual inspection of the emergency release clevis of the MLG to determine if an incorrect clevis has been installed, and if necessary, replacing the clevis with a correct clevis and clevis pin. We are proposing this AD to detect and correct improper installation of the clevis, which could cause loss of the alternate release system and prevent the MLG from extending and retracting, and could consequently affect the airplane’s continued safe flight and landing. DATES: We must receive comments on this proposed AD by September 29, 2014. SUMMARY: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt Boulevard, Toronto, Ontario M3K 1Y5, Canada; telephone 416–375– 4000; fax 416–375–4539; email ADDRESSES: Frm 00011 Fmt 4702 thd.qseries@aero.bombardier.com; Internet https://www.bombardier.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Examining the AD Docket Airworthiness Directives; Bombardier, Inc. Airplanes PO 00000 47393 Sfmt 4702 You may examine the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2014– 0528; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Ezra Sasson, Aerospace Engineer, Airframe and Mechanical Systems Branch, ANE– 171, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone (516) 228–7320; fax (516) 794–5531. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2014–0528; Directorate Identifier 2014–NM–060–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued Canadian Airworthiness Directive CF–2013–40, dated December 9, 2013 (referred to after this as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition E:\FR\FM\13AUP1.SGM 13AUP1

Agencies

[Federal Register Volume 79, Number 156 (Wednesday, August 13, 2014)]
[Proposed Rules]
[Pages 47390-47393]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2014-19158]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0530; Directorate Identifier 2014-NM-062-AD]
RIN 2120-AA64


Airworthiness Directives; ATR--GIE Avions de Transport 
R[eacute]gional Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain ATR--GIE Avions de Transport R[eacute]gional Model ATR42-500 
airplanes, and Model ATR72-212A airplanes. This proposed AD was 
prompted by a report that during an inspection of an airplane on the 
production line, interference was detected between the electrical 
harness and a bonding lead due to an incorrect installation of the 
affected bonding lead. This proposed AD would require a detailed 
inspection for damage or incorrect routing of the bonding lead routing 
above the 120VU shelf, and if any damage or incorrect routing is found, 
modifying the bonding lead routing. We are proposing this AD to detect 
and correct installation of the bonding lead, which could cause arcing 
and chafing, and could possibly result in an uncontrolled fire.

DATES: We must receive comments on this proposed AD by September 29, 
2014.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
ATR--GIE Avions de Transport R[eacute]gional, 1, All[eacute]e Pierre 
Nadot, 31712 Blagnac Cedex, France; telephone +33 (0) 5 62 21 62 21;

[[Page 47391]]

fax +33 (0) 5 62 21 67 18; email continued.airworthiness@atr.fr; 
Internet https://www.aerochain.com. You may view this referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0530; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1137; 
fax 425-227-1149.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2014-0530; 
Directorate Identifier 2014-NM-062-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued 
Airworthiness Directive 2014-0056, dated March 7, 2014 (referred to 
after this as the Mandatory Continuing Airworthiness Information, or 
``the MCAI''), to correct an unsafe condition for certain ATR--GIE 
Avions de Transport R[eacute]gional Model ATR42-500 airplanes, and 
Model ATR72-212A airplanes. The MCAI states:

    During inspection of an aeroplane on the production line, 
interference was detected between electrical harnesses (2M-2S-6M) 
and a bonding lead, located in zone 214, positioned above and 
forward of the 120VU shelf. Subsequent investigation revealed that 
the interference was a result of an incorrect installation of the 
affected bonding lead.
    This condition, if not detected and corrected, could lead to 
arcing and chafing, possibly resulting in an uncontrolled fire.
    To address this potential unsafe condition, ATR issued Service 
Bulletin (SB) ATR42-92-0025 and SB ATR72-92-1034, as applicable to 
aeroplane model, to provide inspection instructions.
    For the reasons described above, this [EASA] AD requires a one-
time [detailed] inspection [for damage or incorrect routing of the 
bonding lead routing above the 120VU shelf] of the electrical 
harness 2M-2S-6M in zone 214 and, depending on findings, 
accomplishment of corrective action(s).

    You may examine the MCAI in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0530.

Relevant Service Information

    ATR--GIE Avions de Transport R[eacute]gional has issued ATR Service 
Bulletin ATR42-92-0025, dated November 7, 2013; and ATR Service 
Bulletin ATR72-92-1034, dated November 7, 2013. The actions described 
in this service information are intended to correct the unsafe 
condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of these 
same type designs.

``Contacting the Manufacturer'' Paragraph in This Proposed AD

    Since late 2006, we have included a standard paragraph titled 
``Airworthy Product'' in all MCAI ADs in which the FAA develops an AD 
based on a foreign authority's AD.
    The MCAI or referenced service information in an FAA AD often 
directs the owner/operator to contact the manufacturer for corrective 
actions, such as a repair. Briefly, the Airworthy Product paragraph 
allowed owners/operators to use corrective actions provided by the 
manufacturer if those actions were FAA-approved. In addition, the 
paragraph stated that any actions approved by the State of Design 
Authority (or its delegated agent) are considered to be FAA-approved.
    In an NPRM having Directorate Identifier 2012-NM-101-AD (78 FR 
78285, December 26, 2013), we proposed to prevent the use of repairs 
that were not specifically developed to correct the unsafe condition, 
by requiring that the repair approval provided by the State of Design 
Authority or its delegated agent specifically refer to the FAA AD. This 
change was intended to clarify the method of compliance and to provide 
operators with better visibility of repairs that are specifically 
developed and approved to correct the unsafe condition. In addition, we 
proposed to change the phrase ``its delegated agent'' to include a 
design approval holder (DAH) with State of Design Authority design 
organization approval (DOA), as applicable, to refer to a DAH 
authorized to approve required repairs for the proposed AD.
    One commenter to the NPRM having Directorate Identifier 2012-NM-
101-AD (78 FR 78285, December 26, 2013) stated the following: ``The 
proposed wording, being specific to repairs, eliminates the 
interpretation that Airbus messages are acceptable for approving minor 
deviations (corrective actions) needed during accomplishment of an AD 
mandated Airbus service bulletin.''
    This comment has made the FAA aware that some operators have 
misunderstood or misinterpreted the Airworthy Product paragraph to 
allow the owner/operator to use messages provided by the manufacturer 
as approval of deviations during the accomplishment of an AD-mandated 
action. The Airworthy Product paragraph does not approve messages or 
other information provided by the manufacturer for deviations to the 
requirements of the AD-mandated actions. The Airworthy Product 
paragraph only addresses the requirement to contact the manufacturer 
for corrective actions for the identified unsafe condition and does not 
cover deviations from other AD requirements. However, deviations to AD-
required actions are addressed in 14 CFR 39.17, and anyone may request 
the approval for an alternative method of compliance to the AD-required 
actions using the procedures found in 14 CFR 39.19.

[[Page 47392]]

    To address this misunderstanding and misinterpretation of the 
Airworthy Product paragraph, we have changed the paragraph and retitled 
it ``Contacting the Manufacturer.'' This paragraph now clarifies that 
for any requirement in this proposed AD to obtain corrective actions 
from a manufacturer, the actions must be accomplished using a method 
approved by the FAA, the European Aviation Safety Agency (EASA), or 
ATR--GIE Avions de Transport R[eacute]gional's EASA DOA.
    The Contacting the Manufacturer paragraph also clarifies that, if 
approved by the DOA, the approval must include the DOA-authorized 
signature. The DOA signature indicates that the data and information 
contained in the document are EASA-approved, which is also FAA-
approved. Messages and other information provided by the manufacturer 
that do not contain the DOA-authorized signature approval are not EASA-
approved, unless EASA directly approves the manufacturer's message or 
other information.
    This clarification does not remove flexibility previously afforded 
by the Airworthy Product paragraph. Consistent with long-standing FAA 
policy, such flexibility was never intended for required actions. This 
is also consistent with the recommendation of the Airworthiness 
Directive Implementation Aviation Rulemaking Committee to increase 
flexibility in complying with ADs by identifying those actions in 
manufacturers' service instructions that are ``Required for 
Compliance'' with ADs. We continue to work with manufacturers to 
implement this recommendation. But once we determine that an action is 
required, any deviation from the requirement must be approved as an 
alternative method of compliance.

Costs of Compliance

    We estimate that this proposed AD affects 5 airplanes of U.S. 
registry.
    We also estimate that it would take about 2 work-hours per product 
to comply with the basic requirements of this proposed AD. The average 
labor rate is $85 per work-hour. Required parts would cost about $0 per 
product. Based on these figures, we estimate the cost of this proposed 
AD on U.S. operators to be $850, or $170 per product.
    In addition, we estimate that any necessary follow-on actions would 
take about 2 work-hours and require parts costing $0, for a cost of 
$170 per product. We have no way of determining the number of aircraft 
that might need this action.

Authority for this Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

ATR--GIE Avions de Transport R[eacute]gional: Docket No. FAA-2014-
0530; Directorate Identifier 2014-NM-062-AD.

(a) Comments Due Date

    We must receive comments by September 29, 2014.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to ATR--GIE Avions de Transport R[eacute]gional 
airplanes, certificated in any category, as identified in paragraph 
(c)(1) and (c)(2) of this AD.
    (1) Model ATR42-500 airplanes, manufacturer serial numbers 669 
through 1005 inclusive.
    (2) Model ATR72-212A airplanes, manufacturer serial numbers 773, 
774, 776 through 1094 inclusive, 1096 through 1099 inclusive, and 
1101.

(d) Subject

    Air Transport Association (ATA) of America Code 92, Electrical 
Routing.

(e) Reason

    This AD was prompted by a report that during an inspection of an 
airplane on the production line, interference was detected between 
the electrical harness and a bonding lead due to an incorrect 
installation of the affected bonding lead. We are issuing this AD to 
detect and correct installation of the bonding lead, which could 
cause arcing and chafing, and could possibly result in an 
uncontrolled fire.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection

    Within 1,000 flight hours after the effective date of this AD: 
Do a detailed inspection of the bonding lead routing above the 120VU 
shelf for damage (i.e., wire chaffing, evidence of burning) or 
incorrect routing, in accordance with the Accomplishment 
Instructions of ATR Service Bulletin ATR42-92-0025, dated November 
7, 2013 (for Model ATR42-500 airplanes); or ATR Service Bulletin 
ATR72-92-1034, dated November 7, 2013 (for Model ATR72-212A 
airplanes).

(h) Corrective Action

    If, during the inspection required by paragraph (g) of this AD, 
any damage (i.e., wire chaffing, evidence of burning) or incorrect 
routing is found: Before further flight, modify the bonding lead 
routing above the 120VU shelf, in accordance with the Accomplishment 
Instructions of ATR Service Bulletin ATR42-92-0025, dated November 
7, 2013 (for Model ATR42-500 airplanes); or ATR Service Bulletin 
ATR72-92-1034, dated November 7, 2013 (for Model ATR72-212A 
airplanes).

[[Page 47393]]

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to ATTN: Tom 
Rodriguez, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, 
WA 98057-3356; telephone 425-227-1137; fax 425-227-1149. Information 
may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office. The 
AMOC approval letter must specifically reference this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, International 
Branch, ANM-116, Transport Airplane Directorate, FAA; or the 
European Aviation Safety Agency (EASA); or ATR--GIE Avions de 
Transport R[eacute]gional's EASA Design Organization Approval (DOA). 
If approved by the DOA, the approval must include the DOA-authorized 
signature.

(j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) European Aviation Safety Agency Airworthiness Directive 2014-
0056, dated March 7, 2014, for related information. This MCAI may be 
found in the AD docket on the Internet at https://www.regulations.gov 
by searching for and locating Docket No. FAA-2014-0530.
    (2) For service information identified in this AD, contact ATR--
GIE Avions de Transport R[eacute]gional, 1, All[eacute]e Pierre 
Nadot, 31712 Blagnac Cedex, France; telephone +33 (0) 5 62 21 62 21; 
fax +33 (0) 5 62 21 67 18; email continued.airworthiness@atr.fr; 
Internet https://www.aerochain.com. You may view this service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on August 1, 2014.
Jeffrey E. Duven,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-19158 Filed 8-12-14; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.