Airworthiness Directives; Bombardier, Inc. Airplanes, 45135-45137 [2014-18367]

Download as PDF 45135 Proposed Rules Federal Register Vol. 79, No. 149 Monday, August 4, 2014 This section of the FEDERAL REGISTER contains notices to the public of the proposed issuance of rules and regulations. The purpose of these notices is to give interested persons an opportunity to participate in the rule making prior to the adoption of the final rules. DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2014–0489; Directorate Identifier 2014–NM–048–AD] RIN 2120–AA64 Airworthiness Directives; Bombardier, Inc. Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL–600–2B19 (Regional Jet Series 100 & 440) airplanes. This proposed AD was prompted by a report indicating that inboard and outboard hydraulic lines of the brakes were found connected to the incorrect ports on the swivel assembly of the main landing gear (MLG). This proposed AD would require modifying the MLG by installing a new bracket on the left and right lower aft-wing planks. We are proposing this AD to prevent incorrect installation of the brake hydraulic lines, which could cause the brakes and the anti-skid system to operate incorrectly, and cause catastrophic failure of the airplane during a high-speed rejected takeoff. DATES: We must receive comments on this proposed AD by September 18, 2014. SUMMARY: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. mstockstill on DSK4VPTVN1PROD with PROPOSALS ADDRESSES: VerDate Mar<15>2010 17:11 Aug 01, 2014 Jkt 232001 • Hand Delivery: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Bombardier, ˆ Inc., 400 Cote-Vertu Road West, Dorval, ´ Quebec H4S 1Y9, Canada; telephone 514–855–5000; fax 514–855–7401; email thd.crj@aero.bombardier.com; Internet https://www.bombardier.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2014– 0489; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Fabio Buttitta, Aerospace Engineer, Airframe and Mechanical Systems Branch, ANE–171, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone (516) 228–7303; fax (516) 794–5531. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2014–0489; Directorate Identifier 2014–NM–048–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the PO 00000 Frm 00001 Fmt 4702 Sfmt 4702 closing date and may amend this proposed AD based on those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued Canadian Airworthiness Directive CF–2014–10, dated February 12, 2014 (referred to after this as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition for certain Bombardier, Inc. Model CL– 600–2B19 (Regional Jet Series 100 & 440) airplanes. The MCAI states: Cases of inboard and outboard hydraulic brake lines connected to the incorrect port of the swivel assembly on the main landing gear were found in service, including a runway overrun event. Cross-connected brake hydraulic lines can cause the brakes and/or the anti-skid system to operate incorrectly. During a high speed rejected take-off, inability for the brakes to operate correctly could be catastrophic. This [Canadian] AD mandates the modification to prevent inadvertent crossconnection of the inboard and outboard hydraulic brake lines. The required action in this AD includes installing a new bracket on the left and right lower aft-wing planks of the MLG. You may examine the MCAI in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2014– 0489. Relevant Service Information Bombardier, Inc. has issued Service Bulletin 601R–32–110, dated December 19, 2013. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI. FAA’s Determination and Requirements of This Proposed AD This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information E:\FR\FM\04AUP1.SGM 04AUP1 45136 Federal Register / Vol. 79, No. 149 / Monday, August 4, 2014 / Proposed Rules mstockstill on DSK4VPTVN1PROD with PROPOSALS referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design. ‘‘Contacting the Manufacturer’’ Paragraph in This Proposed AD Since late 2006, we have included a standard paragraph titled ‘‘Airworthy Product’’ in all MCAI ADs in which the FAA develops an AD based on a foreign authority’s AD. The MCAI or referenced service information in an FAA AD often directs the owner/operator to contact the manufacturer for corrective actions, such as a repair. Briefly, the Airworthy Product paragraph allowed owners/ operators to use corrective actions provided by the manufacturer if those actions were FAA-approved. In addition, the paragraph stated that any actions approved by the State of Design Authority (or its delegated agent) are considered to be FAA-approved. In an NPRM having Directorate Identifier 2012–NM–101–AD (78 FR 78285, December 26, 2013), we proposed to prevent the use of repairs that were not specifically developed to correct the unsafe condition, by requiring that the repair approval provided by the State of Design Authority or its delegated agent specifically refer to the FAA AD. This change was intended to clarify the method of compliance and to provide operators with better visibility of repairs that are specifically developed and approved to correct the unsafe condition. In addition, we proposed to change the phrase ‘‘its delegated agent’’ to include a design approval holder (DAH) with State of Design Authority design organization approval (DOA), as applicable, to refer to a DAH authorized to approve required repairs for the proposed AD. One commenter to the NPRM having Directorate Identifier 2012–NM–101–AD (78 FR 78285, December 26, 2013) stated the following: ‘‘The proposed wording, being specific to repairs, eliminates the interpretation that Airbus messages are acceptable for approving minor deviations (corrective actions) needed during accomplishment of an AD mandated Airbus service bulletin.’’ This comment has made the FAA aware that some operators have misunderstood or misinterpreted the Airworthy Product paragraph to allow the owner/operator to use messages provided by the manufacturer as approval of deviations during the accomplishment of an AD-mandated action. The Airworthy Product VerDate Mar<15>2010 17:11 Aug 01, 2014 Jkt 232001 paragraph does not approve messages or other information provided by the manufacturer for deviations to the requirements of the AD-mandated actions. The Airworthy Product paragraph only addresses the requirement to contact the manufacturer for corrective actions for the identified unsafe condition and does not cover deviations from other AD requirements. However, deviations to AD-required actions are addressed in 14 CFR 39.17, and anyone may request the approval for an alternative method of compliance to the AD-required actions using the procedures found in 14 CFR 39.19. To address this misunderstanding and misinterpretation of the Airworthy Product paragraph, we have changed the paragraph and retitled it ‘‘Contacting the Manufacturer.’’ This paragraph now clarifies that for any requirement in this proposed AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the FAA, TCCA, or Bombardier’s TCCA Design Approval Organization (DAO). The Contacting the Manufacturer paragraph also clarifies that, if approved by the DAO, the approval must include the DAO-authorized signature. The DAO signature indicates that the data and information contained in the document are TCCA-approved, which is also FAAapproved. Messages and other information provided by the manufacturer that do not contain the DAO-authorized signature approval are not TCCA-approved, unless TCCA directly approves the manufacturer’s message or other information. This clarification does not remove flexibility previously afforded by the Airworthy Product paragraph. Consistent with long-standing FAA policy, such flexibility was never intended for required actions. This is also consistent with the recommendation of the Airworthiness Directive Implementation Aviation Rulemaking Committee to increase flexibility in complying with ADs by identifying those actions in manufacturers’ service instructions that are ‘‘Required for Compliance’’ with ADs. We continue to work with manufacturers to implement this recommendation. But once we determine that an action is required, any deviation from the requirement must be approved as an alternative method of compliance. Costs of Compliance We estimate that this proposed AD affects 526 airplanes of U.S. registry. We also estimate that it would take about 6 work-hours per product to PO 00000 Frm 00002 Fmt 4702 Sfmt 4702 comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Required parts would cost about $375 per product. Based on these figures, we estimate the cost of this proposed AD on U.S. operators to be $465,510, or $885 per product. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This proposed regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); 3. Will not affect intrastate aviation in Alaska; and 4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, E:\FR\FM\04AUP1.SGM 04AUP1 Federal Register / Vol. 79, No. 149 / Monday, August 4, 2014 / Proposed Rules the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ Bombardier, Inc.: Docket No. FAA–2014– 0489; Directorate Identifier 2014–NM– 048–AD. (a) Comments Due Date We must receive comments by September 18, 2014. (b) Affected ADs None. (c) Applicability This AD applies to Bombardier, Inc. Model CL–600–2B19 (Regional Jet Series 100 & 440) airplanes, certificated in any category, serial numbers 7003 and subsequent. (d) Subject Air Transport Association (ATA) of America Code 32, Landing Gear. (e) Reason This AD was prompted by a by a report indicating that inboard and outboard hydraulic lines of the brakes were found connected to the incorrect ports on the swivel assembly of the main landing gear (MLG). We are issuing this AD to prevent incorrect installation of the brake hydraulic lines, which could cause the brakes and the anti-skid system to operate incorrectly, and cause catastrophic failure of the airplane during a high-speed rejected take-off. (f) Compliance Comply with this AD within the compliance times specified, unless already done. mstockstill on DSK4VPTVN1PROD with PROPOSALS (g) Modification Within 6,600 flight hours after the effective date of this AD, but no later than 36 months after the effective date of this AD: Modify the MLG by installing a new bracket on the left and right lower aft-wing planks, in accordance with the Accomplishment Instruction of Bombardier Service Bulletin 601R–32–110, dated December 19, 2013. (h) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, New York Aircraft Certification Office (ACO), ANE–170, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information VerDate Mar<15>2010 17:11 Aug 01, 2014 Jkt 232001 directly to the New York ACO, send it to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516 228–7300; fax 516– 794–5531. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. The AMOC approval letter must specifically reference this AD. (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, New York ACO, ANE–170, Engine and Propeller Directorate, FAA; or Transport Canada Civil Aviation (TCCA); or Bombardier, Inc.’s TCCA Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAOauthorized signature. 45137 Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This proposed AD was prompted by a report of two cases of heavy (hard to move) aileron control caused by aileron cables stuck in a clump of ice in the wheel bay. This proposed AD would require installing drain tubes on the center wing rear spar. We are proposing this AD to prevent accumulated water near or on the aileron control cables, which could freeze and result in reduced control of the airplane. DATES: We must receive comments on this proposed AD by September 18, 2014. DEPARTMENT OF TRANSPORTATION You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Fokker Services B.V., Technical Services Dept., P.O. Box 1357, 2130 EL Hoofddorp, the Netherlands; telephone +31 (0)88–6280– 350; fax +31 (0)88–6280–111; email technicalservices@fokker.com; Internet https://www.myfokkerfleet.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Federal Aviation Administration Examining the AD Docket (i) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) Canadian Airworthiness Directive CF–2014–10, dated February 12, 2014, for related information. This MCAI may be found in the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA–2014–0489. (2) For service information identified in ˆ this AD, contact Bombardier, Inc., 400 Cote´ Vertu Road West, Dorval, Quebec H4S 1Y9, Canada; telephone 514–855–5000; fax 514– 855–7401; email thd.crj@ aero.bombardier.com; Internet https:// www.bombardier.com. You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Issued in Renton, Washington, on July 18, 2014. John P. Piccola, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2014–18367 Filed 8–1–14; 8:45 am] BILLING CODE 4910–13–P 14 CFR Part 39 [Docket No. FAA–2014–0492; Directorate Identifier 2013–NM–134–AD] RIN 2120–AA64 Airworthiness Directives; Fokker Services B.V. Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for all SUMMARY: PO 00000 Frm 00003 Fmt 4702 Sfmt 4702 ADDRESSES: You may examine the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2014– 0492; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. E:\FR\FM\04AUP1.SGM 04AUP1

Agencies

[Federal Register Volume 79, Number 149 (Monday, August 4, 2014)]
[Proposed Rules]
[Pages 45135-45137]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2014-18367]


========================================================================
Proposed Rules
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains notices to the public of 
the proposed issuance of rules and regulations. The purpose of these 
notices is to give interested persons an opportunity to participate in 
the rule making prior to the adoption of the final rules.

========================================================================


Federal Register / Vol. 79, No. 149 / Monday, August 4, 2014 / 
Proposed Rules

[[Page 45135]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0489; Directorate Identifier 2014-NM-048-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 
440) airplanes. This proposed AD was prompted by a report indicating 
that inboard and outboard hydraulic lines of the brakes were found 
connected to the incorrect ports on the swivel assembly of the main 
landing gear (MLG). This proposed AD would require modifying the MLG by 
installing a new bracket on the left and right lower aft-wing planks. 
We are proposing this AD to prevent incorrect installation of the brake 
hydraulic lines, which could cause the brakes and the anti-skid system 
to operate incorrectly, and cause catastrophic failure of the airplane 
during a high-speed rejected takeoff.

DATES: We must receive comments on this proposed AD by September 18, 
2014.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; email 
thd.crj@aero.bombardier.com; Internet https://www.bombardier.com. You 
may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0489; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Fabio Buttitta, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone (516) 228-7303; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2014-0489; 
Directorate Identifier 2014-NM-048-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2014-10, dated February 12, 2014 (referred to after this as the 
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to 
correct an unsafe condition for certain Bombardier, Inc. Model CL-600-
2B19 (Regional Jet Series 100 & 440) airplanes. The MCAI states:

    Cases of inboard and outboard hydraulic brake lines connected to 
the incorrect port of the swivel assembly on the main landing gear 
were found in service, including a runway overrun event. Cross-
connected brake hydraulic lines can cause the brakes and/or the 
anti-skid system to operate incorrectly. During a high speed 
rejected take-off, inability for the brakes to operate correctly 
could be catastrophic.
    This [Canadian] AD mandates the modification to prevent 
inadvertent cross-connection of the inboard and outboard hydraulic 
brake lines.

    The required action in this AD includes installing a new bracket on 
the left and right lower aft-wing planks of the MLG. You may examine 
the MCAI in the AD docket on the Internet at https://www.regulations.gov 
by searching for and locating Docket No. FAA-2014-0489.

Relevant Service Information

    Bombardier, Inc. has issued Service Bulletin 601R-32-110, dated 
December 19, 2013. The actions described in this service information 
are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information

[[Page 45136]]

referenced above. We are proposing this AD because we evaluated all 
pertinent information and determined an unsafe condition exists and is 
likely to exist or develop on other products of the same type design.

``Contacting the Manufacturer'' Paragraph in This Proposed AD

    Since late 2006, we have included a standard paragraph titled 
``Airworthy Product'' in all MCAI ADs in which the FAA develops an AD 
based on a foreign authority's AD.
    The MCAI or referenced service information in an FAA AD often 
directs the owner/operator to contact the manufacturer for corrective 
actions, such as a repair. Briefly, the Airworthy Product paragraph 
allowed owners/operators to use corrective actions provided by the 
manufacturer if those actions were FAA-approved. In addition, the 
paragraph stated that any actions approved by the State of Design 
Authority (or its delegated agent) are considered to be FAA-approved.
    In an NPRM having Directorate Identifier 2012-NM-101-AD (78 FR 
78285, December 26, 2013), we proposed to prevent the use of repairs 
that were not specifically developed to correct the unsafe condition, 
by requiring that the repair approval provided by the State of Design 
Authority or its delegated agent specifically refer to the FAA AD. This 
change was intended to clarify the method of compliance and to provide 
operators with better visibility of repairs that are specifically 
developed and approved to correct the unsafe condition. In addition, we 
proposed to change the phrase ``its delegated agent'' to include a 
design approval holder (DAH) with State of Design Authority design 
organization approval (DOA), as applicable, to refer to a DAH 
authorized to approve required repairs for the proposed AD.
    One commenter to the NPRM having Directorate Identifier 2012-NM-
101-AD (78 FR 78285, December 26, 2013) stated the following: ``The 
proposed wording, being specific to repairs, eliminates the 
interpretation that Airbus messages are acceptable for approving minor 
deviations (corrective actions) needed during accomplishment of an AD 
mandated Airbus service bulletin.''
    This comment has made the FAA aware that some operators have 
misunderstood or misinterpreted the Airworthy Product paragraph to 
allow the owner/operator to use messages provided by the manufacturer 
as approval of deviations during the accomplishment of an AD-mandated 
action. The Airworthy Product paragraph does not approve messages or 
other information provided by the manufacturer for deviations to the 
requirements of the AD-mandated actions. The Airworthy Product 
paragraph only addresses the requirement to contact the manufacturer 
for corrective actions for the identified unsafe condition and does not 
cover deviations from other AD requirements. However, deviations to AD-
required actions are addressed in 14 CFR 39.17, and anyone may request 
the approval for an alternative method of compliance to the AD-required 
actions using the procedures found in 14 CFR 39.19.
    To address this misunderstanding and misinterpretation of the 
Airworthy Product paragraph, we have changed the paragraph and retitled 
it ``Contacting the Manufacturer.'' This paragraph now clarifies that 
for any requirement in this proposed AD to obtain corrective actions 
from a manufacturer, the action must be accomplished using a method 
approved by the FAA, TCCA, or Bombardier's TCCA Design Approval 
Organization (DAO).
    The Contacting the Manufacturer paragraph also clarifies that, if 
approved by the DAO, the approval must include the DAO-authorized 
signature. The DAO signature indicates that the data and information 
contained in the document are TCCA-approved, which is also FAA-
approved. Messages and other information provided by the manufacturer 
that do not contain the DAO-authorized signature approval are not TCCA-
approved, unless TCCA directly approves the manufacturer's message or 
other information.
    This clarification does not remove flexibility previously afforded 
by the Airworthy Product paragraph. Consistent with long-standing FAA 
policy, such flexibility was never intended for required actions. This 
is also consistent with the recommendation of the Airworthiness 
Directive Implementation Aviation Rulemaking Committee to increase 
flexibility in complying with ADs by identifying those actions in 
manufacturers' service instructions that are ``Required for 
Compliance'' with ADs. We continue to work with manufacturers to 
implement this recommendation. But once we determine that an action is 
required, any deviation from the requirement must be approved as an 
alternative method of compliance.

Costs of Compliance

    We estimate that this proposed AD affects 526 airplanes of U.S. 
registry.
    We also estimate that it would take about 6 work-hours per product 
to comply with the basic requirements of this proposed AD. The average 
labor rate is $85 per work-hour. Required parts would cost about $375 
per product. Based on these figures, we estimate the cost of this 
proposed AD on U.S. operators to be $465,510, or $885 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This proposed regulation is 
within the scope of that authority because it addresses an unsafe 
condition that is likely to exist or develop on products identified in 
this rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator,

[[Page 45137]]

the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Bombardier, Inc.: Docket No. FAA-2014-0489; Directorate Identifier 
2014-NM-048-AD.

(a) Comments Due Date

    We must receive comments by September 18, 2014.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc. Model CL-600-2B19 (Regional 
Jet Series 100 & 440) airplanes, certificated in any category, 
serial numbers 7003 and subsequent.

(d) Subject

    Air Transport Association (ATA) of America Code 32, Landing 
Gear.

(e) Reason

    This AD was prompted by a by a report indicating that inboard 
and outboard hydraulic lines of the brakes were found connected to 
the incorrect ports on the swivel assembly of the main landing gear 
(MLG). We are issuing this AD to prevent incorrect installation of 
the brake hydraulic lines, which could cause the brakes and the 
anti-skid system to operate incorrectly, and cause catastrophic 
failure of the airplane during a high-speed rejected take-off.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Modification

    Within 6,600 flight hours after the effective date of this AD, 
but no later than 36 months after the effective date of this AD: 
Modify the MLG by installing a new bracket on the left and right 
lower aft-wing planks, in accordance with the Accomplishment 
Instruction of Bombardier Service Bulletin 601R-32-110, dated 
December 19, 2013.

(h) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the New York ACO, send it to ATTN: Program Manager, 
Continuing Operational Safety, FAA, New York ACO, 1600 Stewart 
Avenue, Suite 410, Westbury, NY 11590; telephone 516 228-7300; fax 
516-794-5531. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office/
certificate holding district office. The AMOC approval letter must 
specifically reference this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, Engine and Propeller Directorate, FAA; or Transport Canada 
Civil Aviation (TCCA); or Bombardier, Inc.'s TCCA Design Approval 
Organization (DAO). If approved by the DAO, the approval must 
include the DAO-authorized signature.

(i) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2014-10, dated February 
12, 2014, for related information. This MCAI may be found in the AD 
docket on the Internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2014-0489.
    (2) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email thd.crj@aero.bombardier.com; Internet https://www.bombardier.com. You may view this service information at the 
FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, 
WA. For information on the availability of this material at the FAA, 
call 425-227-1221.

    Issued in Renton, Washington, on July 18, 2014.
John P. Piccola,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-18367 Filed 8-1-14; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.