Airworthiness Directives; Pratt & Whitney Division Turbofan Engines, 32197-32199 [2014-12973]

Download as PDF Federal Register / Vol. 79, No. 107 / Wednesday, June 4, 2014 / Proposed Rules 6.A. through 6.C. of Turbomeca S.A. MSB No. 292 72 2849, Version B, dated November 25, 2013, to perform the vibration check. The reporting requirements in paragraphs 6.A.(1)(c), 6.A.(2)(b), and 6.B.(1)(c), and the requirement to return module M01 in paragraph 6.B.(2)(b)2, of Turbomeca S.A. MSB No. 292 72 2849, Version B, dated November 25, 2013, are not required by this AD. (2) For all affected Turbomeca S.A. engines, during each engine shop visit after the effective date of this AD, perform a vibration check of the AGB 41/23-tooth bevel gear meshing. Guidance on performing the vibration check during an engine shop visit can be found in the service information listed in paragraph (i)(3) in the Related Information section. (3) If the AGB does not pass the vibration check required by paragraphs (e)(1) or (e)(2) of this AD, replace the AGB with a part eligible for installation. (f) Credit for Previous Action If you performed a vibration check of the AGB before the effective date of this AD using Turbomeca S.A. MSB No. 292 72 0839, Version A, dated September 9, 2013; or MSB No. 292 72 2849, Version A, dated September 9, 2013, or during an engine shop visit per paragraph (e)(2) of this AD, you met the initial inspection requirement of paragraph (e)(1) of this AD. (g) Definition For the purposes of this AD, an ‘‘engine shop visit’’ is the induction of an engine into the shop for maintenance involving the separation of pairs of major mating engine flanges. The separation of engine flanges solely for the purpose of transportation without subsequent engine maintenance does not constitute an engine shop visit. ehiers on DSK2VPTVN1PROD with PROPOSALS (h) Alternative Methods of Compliance (AMOCs) The Manager, Engine Certification Office, FAA, may approve AMOCs to this AD. Use the procedures found in 14 CFR 39.19 to make your request. (i) Related Information (1) For more information about this AD, contact Mark Riley, Aerospace Engineer, Engine Certification Office, FAA, Engine & Propeller Directorate, 12 New England Executive Park, Burlington, MA 01803; phone: (781) 238–7758; fax: (781) 238–7199; email: mark.riley@faa.gov. (2) Refer to MCAI European Aviation Safety Agency AD 2014–0036, dated February 11, 2014, for related information. You may examine the MCAI in the AD docket on the Internet at https:// www.regulations.gov by searching for and locating it in Docket No. FAA–2014–0164. (3) Turbomeca S.A. MSB No. 292 72 0839, Version B, dated November 25, 2013; and MSB No. 292 72 2849, Version B, dated November 25, 2013, provide guidance on performing the one-time vibration check. Arriel 1 Technical Instruction (TI) No. 292 72 0839, Version E, dated February 20, 2014; Arriel 1 TI No. 292 72 0840, dated November 29, 2013; Arriel 2 TI No. 292 72 2849, Version E, dated February 20, 2014; and VerDate Mar<15>2010 14:53 Jun 03, 2014 Jkt 232001 Arriel 2 TI No. 292 72 2850, dated November 29, 2013, provide detailed instructions on performing the one-time vibration check for Arriel 1 and Arriel 2 engines, respectively. Turbomeca Engine Test Bed Acceptance Test Specifications CCT No. 0292009400, Version T; CCT No. 0292019400, Version R; CCT No. 0292019690, Version I; CCT No. 029201530, Version K; CCT No. 0292019610, Version K; CCT No. 0292029450, Version J; CCT No. 0292029490, Version I; CCT No. 0292029440, Version I; CCT No. 0292029480, Version K; CCT No. 0292029520, Version H; CCT No. 0292029410, Version L; CCT No. 0292029530, Version H; or Turbomeca ID No. 383952; or Turbomeca RTD No. X 292 65 327 2, provide information on performing a vibration check during an engine shop visit. These service documents can be obtained from Turbomeca S.A. using the contact information in paragraph (i)(4) of this proposed AD. (4) For service information identified in this proposed AD, contact Turbomeca, S.A., 40220 Tarnos, France; phone: 33 (0)5 59 74 40 00; telex: 570 042; fax: 33 (0)5 59 74 45 15. (5) You may view this service information at the FAA, Engine & Propeller Directorate, 12 New England Executive Park, Burlington, MA. For information on the availability of this material at the FAA, call 781–238–7125. Issued in Burlington, Massachusetts, on May 28, 2014. Colleen M. D’Alessandro, Assistant Directorate Manager, Engine & Propeller Directorate, Aircraft Certification Service. [FR Doc. 2014–12974 Filed 6–3–14; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2013–0072; Directorate Identifier 2013–NE–04–AD] RIN 2120–AA64 Airworthiness Directives; Pratt & Whitney Division Turbofan Engines Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to supersede airworthiness directive (AD) 2013–15– 09, which applies to all Pratt & Whitney Division (PW) PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090–3 turbofan engine models with certain second-stage high-pressure turbine (HPT) air seals, installed. AD 2013–15–09 currently requires initial and repetitive inspections for cracks in second-stage HPT air seals. Since we issued AD SUMMARY: PO 00000 Frm 00026 Fmt 4702 Sfmt 4702 32197 2013–15–09, we received reports of cracking in the original location on two additional part numbers (P/Ns) as well as reports of through-cracks in a new location in the second-stage HPT air seal. PW has developed a redesigned second-stage HPT air seal that addresses the cracking condition in both locations. This proposed AD would expand the applicability of AD 2013–15–09 to include additional P/Ns, require replacement of the mating hardware if the second-stage HPT air seal is found with a through-crack, and add mandatory terminating action to the repetitive inspections. We are proposing this AD to prevent failure of the secondstage HPT air seal, which could lead to uncontained engine failure and damage to the airplane. DATES: We must receive comments on this proposed AD by August 4, 2014. ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: (202) 493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Pratt & Whitney Division, 400 Main St., East Hartford, CT 06108; phone: (860) 565– 8770; fax: (860) 565–4503. You may view this service information at the FAA, Engine & Propeller Directorate, 12 New England Executive Park, Burlington, MA. For information on the availability of this material at the FAA, call (781) 238–7125. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov by searching for and locating Docket No. FAA–2013– 0072; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (phone: (800) 647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. E:\FR\FM\04JNP1.SGM 04JNP1 32198 Federal Register / Vol. 79, No. 107 / Wednesday, June 4, 2014 / Proposed Rules FOR FURTHER INFORMATION CONTACT: James Gray, Aerospace Engineer, Engine Certification Office, FAA, Engine & Propeller Directorate, 12 New England Executive Park, Burlington, MA 01803; phone: (781) 238–7742; fax: (781) 238– 7199; email: james.e.gray@faa.gov. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2013–0072; Directorate Identifier 2013–NE–04–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD because of those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. ehiers on DSK2VPTVN1PROD with PROPOSALS Discussion On July 19, 2013, we issued AD 2013– 15–09, Amendment 39–17525 (78 FR 49111, August 13, 2013), (‘‘AD 2013– 15–09’’), for all PW PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090–3 turbofan engine models with second-stage HPT air seal, P/N 54L041, installed. AD 2013–15–09 requires initial and repetitive inspections for cracks in second-stage HPT air seals and replacement of air seals that fail inspection. AD 2013–15–09 resulted from the discovery of cracks in secondstage HPT air seals. We issued AD 2013–15–09 to prevent failure of the second-stage HPT air seal, which could lead to uncontained engine failure and damage to the airplane. Actions Since AD 2013–15–09 Was Issued Since we issued AD 2013–15–09, we received multiple reports of throughcracks in a different location on secondstage HPT air seal, P/N 50L041, and reports of cracking in the original location in two additional second-stage HPT air seal P/Ns, 50L960 and 50L976. The cracking in the two additional P/Ns requires that they be added to the applicability of this proposed AD. PW has developed a redesigned secondstage HPT air seal that corrects the cracking condition in both locations. VerDate Mar<15>2010 14:53 Jun 03, 2014 Jkt 232001 The new cracking location in the second-stage HPT air seal, P/N 50L041, is in the front forward fillet radius. PW determined that through-cracks in the front forward fillet radius increase the stresses in the mating hardware in the HPT rotor and that increased stress reduces the life of the first-stage HPT hub, second-stage HPT hub, and secondstage HPT blade retaining plate. Therefore, the first-stage HPT hub, second-stage HPT hub, and second-stage HPT blade retaining plate must be removed from service if the secondstage HPT air seal, P/N 50L041, is found with a through-crack. Relevant Service Information We reviewed PW Alert Service Bulletin (ASB) No. PW4G–112–A72– 330, Revision 2, dated July 11, 2013, which describes procedures for inspecting the second-stage HPT air seal for cracks and PW Service Bulletin (SB) No. PW4G–112–72–332, Revision 2, dated April 9, 2014, which describes procedures for replacing the secondstage HPT air seal. FAA’s Determination We are proposing this AD because we evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop in other products of the same type design. Proposed AD Requirements This proposed AD would expand the population of affected P/Ns, require removal from service of two newly identified P/Ns, require replacement of the mating hardware if the second-stage HPT air seal is found with a throughcrack, and add mandatory terminating action to the repetitive inspection requirements. Costs of Compliance We estimate that this proposed AD would affect 116 engines installed on airplanes of U.S. registry. We also estimate that it would take about 5 hours to perform the inspection required by this proposed AD. The average labor rate is $85 per hour. We estimate that two engines will also require replacement of the first-stage HPT hub, second-stage HPT hub, and second-stage HPT blade retaining plate. We estimate that parts would cost about $698,920 per engine. Based on these figures, we estimate the total cost of this proposed AD to U.S. operators to be $23,420,020. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue PO 00000 Frm 00027 Fmt 4702 Sfmt 4702 rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that the proposed regulation: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), (3) Will not affect intrastate aviation in Alaska to the extent that it justifies making a regulatory distinction, and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. E:\FR\FM\04JNP1.SGM 04JNP1 Federal Register / Vol. 79, No. 107 / Wednesday, June 4, 2014 / Proposed Rules § 39.13 (f) Installation Prohibition [Amended] 2. The FAA amends § 39.13 by removing airworthiness directive (AD) 2013–15–09, Amendment 39–17525 (78 FR 49111, August 13, 2013), and adding the following new AD: ■ Pratt & Whitney Division: Docket No. FAA– 2013–0072; Directorate Identifier 2013– NE–04–AD. (a) Comments Due Date The FAA must receive comments on this AD action by August 4, 2014. (b) Affected ADs This AD supersedes AD 2013–15–09, Amendment 39–17525 (78 FR 49111, August 13, 2013). (c) Applicability This AD applies to all Pratt & Whitney Division (PW) PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090– 3 turbofan engine models with second-stage high-pressure turbine (HPT) air seal, part number (P/N) 54L041, 50L960, or 50L976, installed. ehiers on DSK2VPTVN1PROD with PROPOSALS (d) Unsafe Condition This AD was prompted by additional reports of cracking in the second-stage HPT air seal. We are issuing this AD to prevent failure of the second-stage HPT air seal, which could lead to uncontained engine failure and damage to the airplane. (e) Compliance Comply with this AD within the compliance times specified, unless already done. (1) At the next piece-part exposure after the effective date of this AD, do the following: (i) Remove from service second-stage HPT air seals, P/N 50L960, 50L976, and 50L041. (ii) Fluorescent-penetrant inspect (FPI) second-stage HPT air seal, P/N 50L041, for a through-crack in the front forward fillet radius. (iii) If a through-crack in the front forward fillet radius is found, remove the first-stage HPT hub, second-stage HPT hub, and secondstage HPT blade retaining plate from service. Do not reinstall the first-stage HPT hub, second-stage HPT hub, or second-stage HPT blade retaining plate into any engine. (2) For engines with second-stage HPT air seals, P/N 50L041, installed, perform initial and repetitive inspections for cracks on-wing until the part is removed from the engine as follows: (i) Perform an initial eddy current inspection (ECI) for cracks prior to reaching 2,200 cycles-since-new or within 100 cyclesin-service after the effective date of this AD, whichever occurs later. (ii) Thereafter, repeat the ECI every 1,200 cycles since last inspection, or fewer, depending on the results of the inspection. (iii) Use section 4.0 of the appendix of PW Alert Service Bulletin (ASB) No. PW4G–112– A72–330, Revision 2, dated July 11, 2013, to perform the inspection and use paragraph 8 of the Accomplishment Instructions of PW ASB No. PW4G–112–A72–330, Revision 2, dated July 11, 2013, to disposition the results of the inspection. VerDate Mar<15>2010 14:53 Jun 03, 2014 Jkt 232001 DEPARTMENT OF LABOR After the effective date of this AD, do not install any second-stage HPT air seal P/N 50L041, P/N 50L960, or P/N 50L976 into any engine. 32199 Occupational Safety and Health Administration (g) Definitions (1) For the purpose of this AD, piece-part exposure is when the second-stage HPT air seal is removed from the engine and fully disassembled. (2) For the purpose of this AD, a throughcrack is a crack that has propagated through the thickness of the part and can be seen on both the inner diameter and outer diameter of the front forward fillet radius. 29 CFR Part 1910 [Docket Number: OSHA–2007–0073] RIN 1218–AC17 Emergency Response and Preparedness Occupational Safety and Health Administration (OSHA), Labor. ACTION: Notice of stakeholder meeting. AGENCY: OSHA invites interested parties to participate in an informal stakeholder meeting on emergency response and preparedness. OSHA plans to use the information obtained at the stakeholder meeting as it considers the development of a proposed standard for emergency response and preparedness. SUMMARY: (h) Credit for Previous Actions (1) If you performed an ECI of the secondstage HPT air seal before the effective date of this AD, using PW ASB No. PW4G–112– A72–330, Revision 1, dated February 14, 2013, or earlier version, you have met the requirements of paragraph (e)(2)(i) of this AD. (2) If you performed an in-shop FPI of the second-stage HPT air seal before the effective date of this AD, you have met the requirements of paragraph (e)(2)(i) of this AD. The Manager, Engine Certification Office, FAA, may approve AMOCs for this AD. Use the procedures found in 14 CFR 39.19 to make your request. Date and location for the stakeholder meeting are: July 30, 2014, at 9:00 a.m., in Washington, DC. If needed, a second session will be held July 31, 2014. The deadline to request registration for the meeting is July 2, 2014. ADDRESSES: (j) Related Information I. Registration (i) Alternative Methods of Compliance (AMOCs) (1) For more information about this AD, contact James Gray, Aerospace Engineer, Engine Certification Office, FAA, Engine & Propeller Directorate, 12 New England Executive Park, Burlington, MA 01803; phone: (781) 238–7742; fax: (781) 238–7199; email: james.e.gray@faa.gov. (2) For service information identified in this AD, contact Pratt & Whitney Division, 400 Main St., East Hartford, CT 06108; phone: (860) 565–8770; fax: (860) 565–4503. (3) You may view this service information at the FAA, Engine & Propeller Directorate, 12 New England Executive Park, Burlington, MA. For information on the availability of this material at the FAA, call (781) 238–7125. Issued in Burlington, Massachusetts, on May 28, 2014. Colleen M. D’Alessandro, Assistant Directorate Manager, Engine & Propeller Directorate, Aircraft Certification Service. [FR Doc. 2014–12973 Filed 6–3–14; 8:45 am] BILLING CODE 4910–13–P PO 00000 Frm 00028 Fmt 4702 Sfmt 4702 DATES: Submit your request to attend the stakeholder meeting by one of the following methods: • Electronic. Register at https:// ersregistration.pec1.net/ (follow the instructions online). • Facsimile. Fax your request to (240) 686–3959 and label it ‘‘Attention: OSHA Emergency Response and Preparedness Stakeholder Meeting Registration.’’ • Regular or express mail, hand delivery, or messenger (courier) service. Send your request, postmarked by July 2, to: Project Enhancement Corporation, 20300 Century Blvd. Ste. 175, Germantown, MD 20874; Attention: OSHA Emergency Response and Preparedness Stakeholder Meeting Registration. II. Stakeholder Meeting The stakeholder meeting will be held at the Frances Perkins Building, 200 Constitution Avenue NW., Washington, DC, 20210. FOR FURTHER INFORMATION CONTACT: Information regarding this notice is available from the following sources: • Press inquiries. Contact Frank Meilinger, Director, OSHA Office of Communications, Room N–3647, U.S. Department of Labor, 200 Constitution Avenue NW., Washington, DC, 20210; E:\FR\FM\04JNP1.SGM 04JNP1

Agencies

[Federal Register Volume 79, Number 107 (Wednesday, June 4, 2014)]
[Proposed Rules]
[Pages 32197-32199]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2014-12973]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-0072; Directorate Identifier 2013-NE-04-AD]
RIN 2120-AA64


Airworthiness Directives; Pratt & Whitney Division Turbofan 
Engines

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to supersede airworthiness directive (AD) 2013-15-
09, which applies to all Pratt & Whitney Division (PW) PW4074, PW4074D, 
PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 turbofan engine models 
with certain second-stage high-pressure turbine (HPT) air seals, 
installed. AD 2013-15-09 currently requires initial and repetitive 
inspections for cracks in second-stage HPT air seals. Since we issued 
AD 2013-15-09, we received reports of cracking in the original location 
on two additional part numbers (P/Ns) as well as reports of through-
cracks in a new location in the second-stage HPT air seal. PW has 
developed a redesigned second-stage HPT air seal that addresses the 
cracking condition in both locations. This proposed AD would expand the 
applicability of AD 2013-15-09 to include additional P/Ns, require 
replacement of the mating hardware if the second-stage HPT air seal is 
found with a through-crack, and add mandatory terminating action to the 
repetitive inspections. We are proposing this AD to prevent failure of 
the second-stage HPT air seal, which could lead to uncontained engine 
failure and damage to the airplane.

DATES: We must receive comments on this proposed AD by August 4, 2014.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Pratt & Whitney Division, 400 Main St., East Hartford, CT 06108; phone: 
(860) 565-8770; fax: (860) 565-4503. You may view this service 
information at the FAA, Engine & Propeller Directorate, 12 New England 
Executive Park, Burlington, MA. For information on the availability of 
this material at the FAA, call (781) 238-7125.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2013-
0072; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: (800) 647-5527) is in the ADDRESSES section. Comments 
will be available in the AD docket shortly after receipt.

[[Page 32198]]


FOR FURTHER INFORMATION CONTACT: James Gray, Aerospace Engineer, Engine 
Certification Office, FAA, Engine & Propeller Directorate, 12 New 
England Executive Park, Burlington, MA 01803; phone: (781) 238-7742; 
fax: (781) 238-7199; email: james.e.gray@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2013-0072; 
Directorate Identifier 2013-NE-04-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    On July 19, 2013, we issued AD 2013-15-09, Amendment 39-17525 (78 
FR 49111, August 13, 2013), (``AD 2013-15-09''), for all PW PW4074, 
PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 turbofan engine 
models with second-stage HPT air seal, P/N 54L041, installed. AD 2013-
15-09 requires initial and repetitive inspections for cracks in second-
stage HPT air seals and replacement of air seals that fail inspection. 
AD 2013-15-09 resulted from the discovery of cracks in second-stage HPT 
air seals. We issued AD 2013-15-09 to prevent failure of the second-
stage HPT air seal, which could lead to uncontained engine failure and 
damage to the airplane.

Actions Since AD 2013-15-09 Was Issued

    Since we issued AD 2013-15-09, we received multiple reports of 
through-cracks in a different location on second-stage HPT air seal, P/
N 50L041, and reports of cracking in the original location in two 
additional second-stage HPT air seal P/Ns, 50L960 and 50L976. The 
cracking in the two additional P/Ns requires that they be added to the 
applicability of this proposed AD. PW has developed a redesigned 
second-stage HPT air seal that corrects the cracking condition in both 
locations.
    The new cracking location in the second-stage HPT air seal, P/N 
50L041, is in the front forward fillet radius. PW determined that 
through-cracks in the front forward fillet radius increase the stresses 
in the mating hardware in the HPT rotor and that increased stress 
reduces the life of the first-stage HPT hub, second-stage HPT hub, and 
second-stage HPT blade retaining plate. Therefore, the first-stage HPT 
hub, second-stage HPT hub, and second-stage HPT blade retaining plate 
must be removed from service if the second-stage HPT air seal, P/N 
50L041, is found with a through-crack.

Relevant Service Information

    We reviewed PW Alert Service Bulletin (ASB) No. PW4G-112-A72-330, 
Revision 2, dated July 11, 2013, which describes procedures for 
inspecting the second-stage HPT air seal for cracks and PW Service 
Bulletin (SB) No. PW4G-112-72-332, Revision 2, dated April 9, 2014, 
which describes procedures for replacing the second-stage HPT air seal.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would expand the population of affected P/Ns, 
require removal from service of two newly identified P/Ns, require 
replacement of the mating hardware if the second-stage HPT air seal is 
found with a through-crack, and add mandatory terminating action to the 
repetitive inspection requirements.

Costs of Compliance

    We estimate that this proposed AD would affect 116 engines 
installed on airplanes of U.S. registry. We also estimate that it would 
take about 5 hours to perform the inspection required by this proposed 
AD. The average labor rate is $85 per hour. We estimate that two 
engines will also require replacement of the first-stage HPT hub, 
second-stage HPT hub, and second-stage HPT blade retaining plate. We 
estimate that parts would cost about $698,920 per engine. Based on 
these figures, we estimate the total cost of this proposed AD to U.S. 
operators to be $23,420,020.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska to the extent 
that it justifies making a regulatory distinction, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.

[[Page 32199]]

Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing airworthiness directive (AD) 
2013-15-09, Amendment 39-17525 (78 FR 49111, August 13, 2013), and 
adding the following new AD:

Pratt & Whitney Division: Docket No. FAA-2013-0072; Directorate 
Identifier 2013-NE-04-AD.

(a) Comments Due Date

    The FAA must receive comments on this AD action by August 4, 
2014.

(b) Affected ADs

    This AD supersedes AD 2013-15-09, Amendment 39-17525 (78 FR 
49111, August 13, 2013).

(c) Applicability

    This AD applies to all Pratt & Whitney Division (PW) PW4074, 
PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 turbofan 
engine models with second-stage high-pressure turbine (HPT) air 
seal, part number (P/N) 54L041, 50L960, or 50L976, installed.

(d) Unsafe Condition

    This AD was prompted by additional reports of cracking in the 
second-stage HPT air seal. We are issuing this AD to prevent failure 
of the second-stage HPT air seal, which could lead to uncontained 
engine failure and damage to the airplane.

(e) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.
    (1) At the next piece-part exposure after the effective date of 
this AD, do the following:
    (i) Remove from service second-stage HPT air seals, P/N 50L960, 
50L976, and 50L041.
    (ii) Fluorescent-penetrant inspect (FPI) second-stage HPT air 
seal, P/N 50L041, for a through-crack in the front forward fillet 
radius.
    (iii) If a through-crack in the front forward fillet radius is 
found, remove the first-stage HPT hub, second-stage HPT hub, and 
second-stage HPT blade retaining plate from service. Do not 
reinstall the first-stage HPT hub, second-stage HPT hub, or second-
stage HPT blade retaining plate into any engine.
    (2) For engines with second-stage HPT air seals, P/N 50L041, 
installed, perform initial and repetitive inspections for cracks on-
wing until the part is removed from the engine as follows:
    (i) Perform an initial eddy current inspection (ECI) for cracks 
prior to reaching 2,200 cycles-since-new or within 100 cycles-in-
service after the effective date of this AD, whichever occurs later.
    (ii) Thereafter, repeat the ECI every 1,200 cycles since last 
inspection, or fewer, depending on the results of the inspection.
    (iii) Use section 4.0 of the appendix of PW Alert Service 
Bulletin (ASB) No. PW4G-112-A72-330, Revision 2, dated July 11, 
2013, to perform the inspection and use paragraph 8 of the 
Accomplishment Instructions of PW ASB No. PW4G-112-A72-330, Revision 
2, dated July 11, 2013, to disposition the results of the 
inspection.

(f) Installation Prohibition

    After the effective date of this AD, do not install any second-
stage HPT air seal P/N 50L041, P/N 50L960, or P/N 50L976 into any 
engine.

(g) Definitions

    (1) For the purpose of this AD, piece-part exposure is when the 
second-stage HPT air seal is removed from the engine and fully 
disassembled.
    (2) For the purpose of this AD, a through-crack is a crack that 
has propagated through the thickness of the part and can be seen on 
both the inner diameter and outer diameter of the front forward 
fillet radius.

(h) Credit for Previous Actions

    (1) If you performed an ECI of the second-stage HPT air seal 
before the effective date of this AD, using PW ASB No. PW4G-112-A72-
330, Revision 1, dated February 14, 2013, or earlier version, you 
have met the requirements of paragraph (e)(2)(i) of this AD.
    (2) If you performed an in-shop FPI of the second-stage HPT air 
seal before the effective date of this AD, you have met the 
requirements of paragraph (e)(2)(i) of this AD.

(i) Alternative Methods of Compliance (AMOCs)

    The Manager, Engine Certification Office, FAA, may approve AMOCs 
for this AD. Use the procedures found in 14 CFR 39.19 to make your 
request.

(j) Related Information

    (1) For more information about this AD, contact James Gray, 
Aerospace Engineer, Engine Certification Office, FAA, Engine & 
Propeller Directorate, 12 New England Executive Park, Burlington, MA 
01803; phone: (781) 238-7742; fax: (781) 238-7199; email: 
james.e.gray@faa.gov.
    (2) For service information identified in this AD, contact Pratt 
& Whitney Division, 400 Main St., East Hartford, CT 06108; phone: 
(860) 565-8770; fax: (860) 565-4503.
    (3) You may view this service information at the FAA, Engine & 
Propeller Directorate, 12 New England Executive Park, Burlington, 
MA. For information on the availability of this material at the FAA, 
call (781) 238-7125.

    Issued in Burlington, Massachusetts, on May 28, 2014.
Colleen M. D'Alessandro,
Assistant Directorate Manager, Engine & Propeller Directorate, Aircraft 
Certification Service.
[FR Doc. 2014-12973 Filed 6-3-14; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.