Airworthiness Directives; Various Restricted Category Helicopters, 9385-9387 [2014-02962]

Download as PDF Federal Register / Vol. 79, No. 33 / Wednesday, February 19, 2014 / Rules and Regulations to the International Branch, send it to ATTN: Vladimir Ulyanov, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; telephone 425–227–1138; fax 425–227–1149. Information may be emailed to: 9-ANM-116AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The AMOC approval letter must specifically reference this AD. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they were approved by the State of Design Authority (or its delegated agent, or by the Design Approval Holder with a State of Design Authority’s design organization approval). For a repair method to be approved, the repair approval must specifically refer to this AD. You are required to ensure the product is airworthy before it is returned to service. ehiers on DSK2VPTVN1PROD with RULES (m) Related Information (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) The European Aviation Safety Agency Airworthiness Directive 2013–0033, dated February 19, 2013, for related information. You may examine the MCAI in the AD docket on the Internet https:// www.regulations.gov/ #!documentDetail;D=FAA-2013-0632-0002. (2) Service information identified in this AD that is not incorporated by reference may be obtained at the addresses specified in paragraphs (n)(4) and (n)(5) of this AD. (n) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) Airbus Mandatory Service Bulletin A330–33–3041, Revision 01, dated July 10, 2012. (ii) Airbus Mandatory Service Bulletin A330–36–3040, Revision 01, dated November 26, 2012. (iii) Airbus Mandatory Service Bulletin A340–33–4026, Revision 01, dated July 10, 2012. (iv) Airbus Mandatory Service Bulletin A340–33–5006, dated January 3, 2012. (v) Airbus Mandatory Service Bulletin A340–36–4035, Revision 01, dated September 24, 2013. (vi) Airbus Mandatory Service Bulletin A340–53–5031, Revision 02, dated August 3, 2011. (vii) Airbus Service Bulletin A330–36– 3037, Revision 01, dated January 24, 2013. (viii) Airbus Service Bulletin A330–36– 3038, dated January 16, 2012. (ix) Airbus Service Bulletin A340–36– 4033, Revision 01, dated January 28, 2013. (3) For service information identified in this AD, contact Airbus SAS, Airworthiness VerDate Mar<15>2010 14:22 Feb 18, 2014 Jkt 232001 Office—EAL, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 45 80; email airworthiness.A330-A340@airbus.com; Internet https://www.airbus.com. (4) You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https:// www.archives.gov/federal-register/cfr/ibrlocations.html. Issued in Renton, Washington, on January 31, 2014. John P. Piccola, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2014–02994 Filed 2–18–14; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2013–0736; Directorate Identifier 2013–SW–013–AD; Amendment 39–17747; AD 2014–03–10] RIN 2120–AA64 Airworthiness Directives; Various Restricted Category Helicopters Federal Aviation Administration (FAA), DOT. ACTION: Final rule. AGENCY: We are adopting a new airworthiness directive (AD) for various restricted category helicopters, originally manufactured by Bell Helicopter Textron, Inc. (Bell), model numbers HH–1K, TH–1F, TH–1L, UH– 1A, UH–1B, UH–1E, UH–1F, UH–1H, UH–1L, and UH–1P. This AD requires inspecting the tail rotor (T/R) cable assembly for an incorrectly machined body. This AD is prompted by a report from Bell that a defective body on the cable prevents the barrel assembly from fully engaging in the body cavity. These actions are intended to prevent disengagement of the cable from the barrel, failure of the T/R pitch control, and subsequent loss of control of the helicopter. This AD is effective March 26, 2014. The Director of the Federal Register approved the incorporation by reference of a certain document listed in this AD as of March 26, 2014. PO 00000 Frm 00007 Fmt 4700 Sfmt 4700 For service information identified in this AD, contact Bell Helicopter Textron, Inc., P.O. Box 482, Fort Worth, TX 76101; telephone (817) 280–3391; fax (817) 280–6466; or at https://www.bellcustomer.com/files/. You may review a copy of the referenced service information at the FAA, Office of the Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth Texas 76137. ADDRESSES: Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov or in person at the Docket Operations Office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, any incorporated-by-reference service information, the economic evaluation, any comments received, and other information. The street address for the Docket Operations Office (phone: 800– 647–5527) is U.S. Department of Transportation, Docket Operations Office, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Helene Gandy, Aviation Safety Engineer, Rotorcraft Certification Office, Rotorcraft Directorate, FAA, 2601 Meacham Blvd., Fort Worth, Texas 76137; telephone (817) 222–5413; email 7-AVS-ASW-170@faa.gov. SUPPLEMENTARY INFORMATION: Discussion SUMMARY: DATES: 9385 On August 20, 2013, at 78 FR 51127, the Federal Register published our notice of proposed rulemaking (NPRM), which proposed to amend 14 CFR part 39 by adding an AD that would apply to various restricted category helicopters originally manufactured by Bell, Model HH–1K, TH–1F, TH–1L, UH–1A, UH– 1B, UH–1E, UH–1F, UH–1H, UH–1L, and UH–1P, with a cable assembly, part number 205–001–720–001 installed. The current type certificate holders for these models include but are not limited to Arrow Falcon Exporters Inc.; AST, Inc.; Bell Helicopter Textron, Inc.; Global Helicopter Technology, Inc.; Hagglund Helicopters, LLC; International Helicopters, Inc.; JJASPP Engineering Services, LLC; Northwest Rotorcraft, LLC; OAS Parts LLC; Richards Heavylift Helo, Inc.; Robinson Air Crane, Inc.; Rotorcraft Development Corporation; San Joaquin Helicopters; Smith Helicopters; Southern Helicopter, Inc.; Southwest Florida Aviation International, Inc.; Tamarack Helicopters, Inc.; and Southwest Florida E:\FR\FM\19FER1.SGM 19FER1 9386 Federal Register / Vol. 79, No. 33 / Wednesday, February 19, 2014 / Rules and Regulations Aviation, Inc. The NPRM proposed to require inspecting each cable assembly to determine if an incorrectly machined body is installed. If an incorrectly machined body is installed, the NPRM proposed to require replacing the cable assembly within 50 hours time-inservice. Until the cable assembly is replaced, the NPRM proposed to require inspecting the assembly for separation daily. The proposed requirements were intended to prevent disengagement of the cable from the body, T/R pitch control failure in a fixed position, and subsequent loss of control of the helicopter. Comments We gave the public the opportunity to participate in developing this AD, but we did not receive any comments on the NPRM (78 FR 51127, August 20, 2013). FAA’s Determination We have reviewed the relevant information and determined that an unsafe condition exists and is likely to exist or develop on other products of the same type design and that air safety and the public interest require adopting the AD requirements as proposed. Related Service Information We reviewed Bell Alert Service Bulletin No. UH–1H–12–08, dated August 28, 2012 (ASB), which describes procedures for inspecting the barrel assembly to determine if an incorrectly machined body is installed. If an incorrectly machined body is installed, the ASB specifies replacing the cable assembly. The ASB further specifies inspecting the barrel assembly and cable connection daily until the cable assembly is replaced. ehiers on DSK2VPTVN1PROD with RULES Differences Between This AD and the Service Information The ASB specifies inspecting the barrel assembly at the next daily inspection; this AD specifies inspecting within 25 hours TIS. The ASB also specifies replacing any defective cable assembly at the next phase inspection, within 50 hours TIS, or by December 31, 2012; this AD specifies replacing the cable assembly within 50 hours TIS. Costs of Compliance We estimate that this AD will affect 716 helicopters of U.S. Registry. We estimate that operators will incur the following costs in order to comply with this AD. At an average labor rate of $85 per hour, inspecting the barrel assembly requires about 1 work-hour, for a cost per helicopter of $85 and a total cost of $60,860 for the fleet. If required, VerDate Mar<15>2010 14:22 Feb 18, 2014 Jkt 232001 replacing a defective cable assembly requires about 8 work-hours, and required parts cost about $625, for a cost per helicopter of $1,305. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866; (2) Is not a ‘‘significant rule’’ under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); (3) Will not affect intrastate aviation in Alaska to the extent that it justifies making a regulatory distinction; and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared an economic evaluation of the estimated costs to comply with this AD and placed it in the AD docket. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PO 00000 Frm 00008 Fmt 4700 Sfmt 4700 PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ 2014–03–10 Various Restricted Category Helicopters: Amendment 39–17747; Docket No. FAA–2013–0736; Directorate Identifier 2013–SW–013–AD. (a) Applicability This AD applies to various restricted category helicopters originally manufactured by Bell Helicopter Textron, Inc., Model HH– 1K, TH–1F, TH–1L, UH–1A, UH–1B, UH–1E, UH–1F, UH–1H, UH–1L, and UH–1P; current type certificate holders include but are not limited to Arrow Falcon Exporters Inc.; AST, Inc.; Bell Helicopter Textron, Inc.; Global Helicopter Technology, Inc.; Hagglund Helicopters, LLC; International Helicopters, Inc.; JJASPP Engineering Services, LLC; Northwest Rotorcraft, LLC; OAS Parts LLC; Richards Heavylift Helo, Inc.; Robinson Air Crane, Inc.; Rotorcraft Development Corporation; San Joaquin Helicopters; Smith Helicopters; Southern Helicopter, Inc.; Southwest Florida Aviation International, Inc.; Tamarack Helicopters, Inc.; and Southwest Florida Aviation, Inc., with a cable assembly, part number 205–001–720– 001 installed, certificated in any category. (b) Unsafe Condition This AD defines the unsafe condition as an incorrectly machined body on the cable assembly, which could prevent the barrel assembly from fully engaging in the body cavity. This condition could result in disengagement of the cable from the barrel, failure of the tail rotor pitch control, and subsequent loss of control of the helicopter. (c) Effective Date This AD becomes effective March 26, 2014. (d) Compliance You are responsible for performing each action required by this AD within the specified compliance time unless it has already been accomplished prior to that time. (e) Required Actions (1) Within 25 hours time in service (TIS), inspect each cable assembly to determine if there is a false cut on the body of the barrel assembly, as depicted in Figure 1 of Bell Alert Service Bulletin No. UH–1H–12–08, dated August 28, 2012. (2) If there is a false cut, before the first flight of each day, inspect the cable assembly for separation of the barrel assembly from the body. If there is any separation, before further flight, replace the cable assembly. (3) Within 50 hours TIS, replace the cable assembly with an airworthy cable assembly that does not have a false cut in the body. Replacing the cable assembly is terminating action for the inspections required by paragraph (e)(2) of this AD. E:\FR\FM\19FER1.SGM 19FER1 Federal Register / Vol. 79, No. 33 / Wednesday, February 19, 2014 / Rules and Regulations (f) Alternative Methods of Compliance (AMOCs) DEPARTMENT OF TRANSPORTATION (1) The Manager, Rotorcraft Certification Office, FAA, may approve AMOCs for this AD. Send your proposal to: Helene Gandy, Aviation Safety Engineer, Rotorcraft Certification Office, Rotorcraft Directorate, FAA, 2601 Meacham Blvd., Fort Worth, Texas 76137; telephone (817) 222–5413; email 7-AVS-ASW-170@faa.gov. (2) For operations conducted under a 14 CFR part 119 operating certificate or under 14 CFR part 91, subpart K, we suggest that you notify your principal inspector, or lacking a principal inspector, the manager of the local flight standards district office or certificate holding district office before operating any aircraft complying with this AD through an AMOC. Federal Aviation Administration Joint Aircraft Service Component (JASC) Code: 6720: Tail Rotor Control System. (h) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Bell Alert Service Bulletin No. UH–1H– 12–08, dated August 28, 2012. (ii) Reserved. (3) For Bell service information identified in this AD, contact Bell Helicopter Textron, Inc., P.O. Box 482, Fort Worth, TX 76101; telephone (817) 280–3391; fax (817) 280– 6466; or at https://www.bellcustomer.com/ files/. (4) You may view this service information at FAA, Office of the Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas 76137. For information on the availability of this material at the FAA, call (817) 222–5110. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741–6030, or go to: https:// www.archives.gov/federal-register/cfr/ibrlocations.html. Issued in Fort Worth, Texas, on January 31, 2014. Lance T. Gant, Acting Directorate Manager, Rotorcraft Directorate, Aircraft Certification Service. [FR Doc. 2014–02962 Filed 2–18–14; 8:45 am] ehiers on DSK2VPTVN1PROD with RULES [Docket No. FAA–2013–0799; Directorate Identifier 2012–NM–153–AD; Amendment 39–17746; AD 2014–03–09] RIN 2120–AA64 Airworthiness Directives; ATR—GIE ´ Avions de Transport Regional Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final Rule. AGENCY: We are adopting a new airworthiness directive (AD) for certain ATR—GIE Avions de Transport ´ Regional Model ATR42 and Model ATR72 airplanes. This AD was prompted by reports of defective sealing between the nacelle lower fairing and the underwing box. This AD requires a one-time general visual inspection for damaged (worn, torn, or abraded) or missing seals between the nacelle lower fairing and the underwing box of both the left-hand and right-hand engine nacelles, and replacement of the seal and/or shims if necessary. We are issuing this AD to prevent the decrease of the fire extinguishing agent efficiency, which could delay fire extinction and allow fire propagation out of the nacelle fire protected area, resulting in damage to the airplane. DATES: This AD becomes effective March 26, 2014. The Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD as of March 26, 2014. ADDRESSES: You may examine the AD docket on the Internet at https:// www.regulations.gov/ #!docketDetail;D=FAA-2013-0799; or in person at the Docket Management Facility, U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC. For service information identified in this AD, contact ATR—GIE Avions de ´ ´ Transport Regional, 1, Allee Pierre Nadot, 31712 Blagnac Cedex, France; telephone +33 (0) 5 62 21 62 21; fax +33 (0) 5 62 21 67 18; email continued.airworthiness@atr.fr; Internet https://www.aerochain.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the SUMMARY: (g) Subject BILLING CODE 4910–13–P VerDate Mar<15>2010 14 CFR Part 39 14:22 Feb 18, 2014 Jkt 232001 PO 00000 Frm 00009 Fmt 4700 Sfmt 4700 9387 availability of this material at the FAA, call 425–227–1221. FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; telephone 425–227–1137; fax 425–227–1149. SUPPLEMENTARY INFORMATION: Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to certain ATR—GIE Avions de ´ Transport Regional Model ATR42 and Model ATR72 airplanes. The NPRM published in the Federal Register on September 25, 2013 (78 FR 58967). The NPRM was prompted by reports of defective sealing between the nacelle lower fairing and the underwing box. The NPRM proposed to require a onetime general visual inspection for damaged (worn, torn, or abraded) or missing seals between the nacelle lower fairing and the underwing box of both the left-hand and right-hand engine nacelles, and replacement of the seal and/or shims if necessary. We are issuing this AD to prevent the decrease of the fire extinguishing agent efficiency, which could delay fire extinction and allow fire propagation out of the nacelle fire protected area, resulting in damage to the airplane. The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued EASA Airworthiness Directive 2012–0160, dated August 24, 2012 (referred to after this as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition for the specified products. The MCAI states: Some cases of defective sealing have been reported on in-service aeroplanes on LeftHand (LH) and Right-Hand (RH), between the nacelle lower fairing and the underwing box. Investigation results have shown that this issue was due to either damaged or missing seal and/or incorrect adjustment of the nacelle lower fairing. This condition, if not detected and corrected, may decrease the extinguishing agent efficiency, delay the fire extinction and allow fire propagation out of the nacelle fire protected area, possibly resulting in damage to the aeroplane. For the reasons described above, this [EASA] AD requires a one-time [general visual] inspection of the affected area [between the nacelle lower fairing and the underbox wing for damaged (worn, torn, or abraded) or missing seals] and, depending on findings, accomplishment of applicable corrective actions to restore the area integrity. E:\FR\FM\19FER1.SGM 19FER1

Agencies

[Federal Register Volume 79, Number 33 (Wednesday, February 19, 2014)]
[Rules and Regulations]
[Pages 9385-9387]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2014-02962]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-0736; Directorate Identifier 2013-SW-013-AD; 
Amendment 39-17747; AD 2014-03-10]
RIN 2120-AA64


Airworthiness Directives; Various Restricted Category Helicopters

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for various 
restricted category helicopters, originally manufactured by Bell 
Helicopter Textron, Inc. (Bell), model numbers HH-1K, TH-1F, TH-1L, UH-
1A, UH-1B, UH-1E, UH-1F, UH-1H, UH-1L, and UH-1P. This AD requires 
inspecting the tail rotor (T/R) cable assembly for an incorrectly 
machined body. This AD is prompted by a report from Bell that a 
defective body on the cable prevents the barrel assembly from fully 
engaging in the body cavity. These actions are intended to prevent 
disengagement of the cable from the barrel, failure of the T/R pitch 
control, and subsequent loss of control of the helicopter.

DATES: This AD is effective March 26, 2014.
    The Director of the Federal Register approved the incorporation by 
reference of a certain document listed in this AD as of March 26, 2014.

ADDRESSES: For service information identified in this AD, contact Bell 
Helicopter Textron, Inc., P.O. Box 482, Fort Worth, TX 76101; telephone 
(817) 280-3391; fax (817) 280-6466; or at https://www.bellcustomer.com/files/. You may review a copy of the referenced service information at 
the FAA, Office of the Regional Counsel, Southwest Region, 2601 Meacham 
Blvd., Room 663, Fort Worth Texas 76137.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov or in person at the Docket Operations Office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, any incorporated-by-reference 
service information, the economic evaluation, any comments received, 
and other information. The street address for the Docket Operations 
Office (phone: 800-647-5527) is U.S. Department of Transportation, 
Docket Operations Office, M-30, West Building Ground Floor, Room W12-
140, 1200 New Jersey Avenue SE., Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Helene Gandy, Aviation Safety 
Engineer, Rotorcraft Certification Office, Rotorcraft Directorate, FAA, 
2601 Meacham Blvd., Fort Worth, Texas 76137; telephone (817) 222-5413; 
email 7-AVS-ASW-170@faa.gov.

SUPPLEMENTARY INFORMATION: 

Discussion

    On August 20, 2013, at 78 FR 51127, the Federal Register published 
our notice of proposed rulemaking (NPRM), which proposed to amend 14 
CFR part 39 by adding an AD that would apply to various restricted 
category helicopters originally manufactured by Bell, Model HH-1K, TH-
1F, TH-1L, UH-1A, UH-1B, UH-1E, UH-1F, UH-1H, UH-1L, and UH-1P, with a 
cable assembly, part number 205-001-720-001 installed. The current type 
certificate holders for these models include but are not limited to 
Arrow Falcon Exporters Inc.; AST, Inc.; Bell Helicopter Textron, Inc.; 
Global Helicopter Technology, Inc.; Hagglund Helicopters, LLC; 
International Helicopters, Inc.; JJASPP Engineering Services, LLC; 
Northwest Rotorcraft, LLC; OAS Parts LLC; Richards Heavylift Helo, 
Inc.; Robinson Air Crane, Inc.; Rotorcraft Development Corporation; San 
Joaquin Helicopters; Smith Helicopters; Southern Helicopter, Inc.; 
Southwest Florida Aviation International, Inc.; Tamarack Helicopters, 
Inc.; and Southwest Florida

[[Page 9386]]

Aviation, Inc. The NPRM proposed to require inspecting each cable 
assembly to determine if an incorrectly machined body is installed. If 
an incorrectly machined body is installed, the NPRM proposed to require 
replacing the cable assembly within 50 hours time-in-service. Until the 
cable assembly is replaced, the NPRM proposed to require inspecting the 
assembly for separation daily.
    The proposed requirements were intended to prevent disengagement of 
the cable from the body, T/R pitch control failure in a fixed position, 
and subsequent loss of control of the helicopter.

Comments

    We gave the public the opportunity to participate in developing 
this AD, but we did not receive any comments on the NPRM (78 FR 51127, 
August 20, 2013).

FAA's Determination

    We have reviewed the relevant information and determined that an 
unsafe condition exists and is likely to exist or develop on other 
products of the same type design and that air safety and the public 
interest require adopting the AD requirements as proposed.

Related Service Information

    We reviewed Bell Alert Service Bulletin No. UH-1H-12-08, dated 
August 28, 2012 (ASB), which describes procedures for inspecting the 
barrel assembly to determine if an incorrectly machined body is 
installed. If an incorrectly machined body is installed, the ASB 
specifies replacing the cable assembly. The ASB further specifies 
inspecting the barrel assembly and cable connection daily until the 
cable assembly is replaced.

Differences Between This AD and the Service Information

    The ASB specifies inspecting the barrel assembly at the next daily 
inspection; this AD specifies inspecting within 25 hours TIS. The ASB 
also specifies replacing any defective cable assembly at the next phase 
inspection, within 50 hours TIS, or by December 31, 2012; this AD 
specifies replacing the cable assembly within 50 hours TIS.

Costs of Compliance

    We estimate that this AD will affect 716 helicopters of U.S. 
Registry. We estimate that operators will incur the following costs in 
order to comply with this AD. At an average labor rate of $85 per hour, 
inspecting the barrel assembly requires about 1 work-hour, for a cost 
per helicopter of $85 and a total cost of $60,860 for the fleet. If 
required, replacing a defective cable assembly requires about 8 work-
hours, and required parts cost about $625, for a cost per helicopter of 
$1,305.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866;
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979);
    (3) Will not affect intrastate aviation in Alaska to the extent 
that it justifies making a regulatory distinction; and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared an economic evaluation of the estimated costs to comply 
with this AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2014-03-10 Various Restricted Category Helicopters: Amendment 39-
17747; Docket No. FAA-2013-0736; Directorate Identifier 2013-SW-013-
AD.

(a) Applicability

    This AD applies to various restricted category helicopters 
originally manufactured by Bell Helicopter Textron, Inc., Model HH-
1K, TH-1F, TH-1L, UH-1A, UH-1B, UH-1E, UH-1F, UH-1H, UH-1L, and UH-
1P; current type certificate holders include but are not limited to 
Arrow Falcon Exporters Inc.; AST, Inc.; Bell Helicopter Textron, 
Inc.; Global Helicopter Technology, Inc.; Hagglund Helicopters, LLC; 
International Helicopters, Inc.; JJASPP Engineering Services, LLC; 
Northwest Rotorcraft, LLC; OAS Parts LLC; Richards Heavylift Helo, 
Inc.; Robinson Air Crane, Inc.; Rotorcraft Development Corporation; 
San Joaquin Helicopters; Smith Helicopters; Southern Helicopter, 
Inc.; Southwest Florida Aviation International, Inc.; Tamarack 
Helicopters, Inc.; and Southwest Florida Aviation, Inc., with a 
cable assembly, part number 205-001-720-001 installed, certificated 
in any category.

 (b) Unsafe Condition

    This AD defines the unsafe condition as an incorrectly machined 
body on the cable assembly, which could prevent the barrel assembly 
from fully engaging in the body cavity. This condition could result 
in disengagement of the cable from the barrel, failure of the tail 
rotor pitch control, and subsequent loss of control of the 
helicopter.

(c) Effective Date

    This AD becomes effective March 26, 2014.

(d) Compliance

    You are responsible for performing each action required by this 
AD within the specified compliance time unless it has already been 
accomplished prior to that time.

(e) Required Actions

    (1) Within 25 hours time in service (TIS), inspect each cable 
assembly to determine if there is a false cut on the body of the 
barrel assembly, as depicted in Figure 1 of Bell Alert Service 
Bulletin No. UH-1H-12-08, dated August 28, 2012.
    (2) If there is a false cut, before the first flight of each 
day, inspect the cable assembly for separation of the barrel 
assembly from the body. If there is any separation, before further 
flight, replace the cable assembly.
    (3) Within 50 hours TIS, replace the cable assembly with an 
airworthy cable assembly that does not have a false cut in the body. 
Replacing the cable assembly is terminating action for the 
inspections required by paragraph (e)(2) of this AD.

[[Page 9387]]

(f) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Rotorcraft Certification Office, FAA, may 
approve AMOCs for this AD. Send your proposal to: Helene Gandy, 
Aviation Safety Engineer, Rotorcraft Certification Office, 
Rotorcraft Directorate, FAA, 2601 Meacham Blvd., Fort Worth, Texas 
76137; telephone (817) 222-5413; email 7-AVS-ASW-170@faa.gov.
    (2) For operations conducted under a 14 CFR part 119 operating 
certificate or under 14 CFR part 91, subpart K, we suggest that you 
notify your principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office or 
certificate holding district office before operating any aircraft 
complying with this AD through an AMOC.

(g) Subject

    Joint Aircraft Service Component (JASC) Code: 6720: Tail Rotor 
Control System.

(h) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Bell Alert Service Bulletin No. UH-1H-12-08, dated August 
28, 2012.
    (ii) Reserved.
    (3) For Bell service information identified in this AD, contact 
Bell Helicopter Textron, Inc., P.O. Box 482, Fort Worth, TX 76101; 
telephone (817) 280-3391; fax (817) 280-6466; or at https://www.bellcustomer.com/files/.
    (4) You may view this service information at FAA, Office of the 
Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, 
Fort Worth, Texas 76137. For information on the availability of this 
material at the FAA, call (817) 222-5110.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call (202) 741-6030, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Fort Worth, Texas, on January 31, 2014.
Lance T. Gant,
Acting Directorate Manager, Rotorcraft Directorate, Aircraft 
Certification Service.
[FR Doc. 2014-02962 Filed 2-18-14; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.