Special Conditions: Airbus, Model A350-900 Series Airplane; Flight Envelope Protection: High Speed Limiting, 1336-1337 [2014-00100]
Download as PDF
1336
Federal Register / Vol. 79, No. 5 / Wednesday, January 8, 2014 / Proposed Rules
are the structural integrity of the wing
and tank, flammability of the tank, burnthrough resistance of the wing skin, and
the presence of auto-ignition threats
during exposure to a fire. The FAA
assessed post-crash survival time during
the adoption of Amendment 25–111 for
fuselage burn-through protection.
Studies conducted by and on behalf of
the FAA indicated that, following a
survivable accident, prevention of
fuselage burn-through for approximately
5 minutes can significantly enhance
survivability.2
There is little benefit in requiring the
design to prevent wing skin burnthrough beyond five minutes, due to the
effects of the fuel fire itself on the rest
of the airplane. That assessment was
carried out based on accidents involving
airplanes with conventional fuel tanks,
and considering the ability of ground
personnel to rescue occupants. In
addition, AC 20–135 indicates that,
when aluminum is used for fuel tanks,
the tank should withstand the effects of
fire for 5 minutes without failure.
Therefore, to be consistent with existing
capability and related requirements, the
Model A350–900 series airplane fuel
tanks must be capable of resisting a
post-crash fire for at least 5 minutes. In
demonstrating compliance, Airbus must
address a range of fuel loads from
minimum to maximum, as well as any
other critical fuel load.
Applicability
Conclusion
This action affects only certain novel
or unusual design features on the Airbus
Model A350–900 series airplanes. It is
not a rule of general applicability.
mstockstill on DSK4VPTVN1PROD with PROPOSALS
List of Subjects in 14 CFR part 25
Aircraft, Aviation safety, Reporting
and recordkeeping requirements.
The authority citation for these
special conditions is as follows:
Issued in Renton, Washington, on October
22, 2013.
Stephen P. Boyd
Acting Manager, Transport Airplane
Directorate, Aircraft Certification Service.
Jkt 232001
BILLING CODE 4910–13–P
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 25
[Docket No. FAA–2013–0901; Notice
No. 25–13–23–SC]
Special Conditions: Airbus, Model
A350–900 Series Airplane; Flight
Envelope Protection: High Speed
Limiting
Federal Aviation
Administration (FAA), DOT.
ACTION: Notice of proposed special
conditions.
AGENCY:
This action proposes special
conditions for Airbus Model A350–900
series airplanes. These airplanes will
have a novel or unusual design feature
associated with high speed limiting. The
applicable airworthiness regulations do
not contain adequate or appropriate
safety standards for this design feature.
These proposed special conditions
contain the additional safety standards
SUMMARY:
2 Cherry, R. and Warren, K. ‘‘Fuselage
Burnthrough Protection for Increased Postcrash
Occupant Survivability: Safety Benefit Analysis
Based on Past Accidents, ‘‘FAA Report DOT/FAA/
AR–99/57, September 1999 and R G W Cherry &
Associates Limited, ‘‘A Benefit Analysis for Cabin
Water Spray Systems and Enhanced Fuselage
Burnthrough Protection,’’ FAA Report DOT/FAA/
AR–02/49, April 7, 2003.
16:18 Jan 07, 2014
The Proposed Special Conditions
Accordingly, pursuant to the
authority delegated to me by the
Administrator, the following special
conditions are proposed as part of the
type certification basis for the Model
A350–900 series airplane:
In addition to complying with 14 CFR
part 25 regulations governing the firesafety performance of the fuel tanks,
wings, and nacelle, the Airbus Model
A350–900 series airplane must
demonstrate acceptable post-crash
survivability in the event the wings are
exposed to a large fuel-fed ground fire.
Airbus must demonstrate that the wing
and fuel tank design can endure an
external fuel-fed pool fire for at least
five minutes. This shall be
demonstrated for minimum fuel loads
(not less than reserve fuel levels) and
maximum fuel loads (maximum range
fuel quantities), and other identified
critical fuel loads. Considerations shall
include fuel tank flammability, burnthrough resistance, wing structural
strength retention properties, and autoignition threats during a ground fire
event for the required time duration.
[FR Doc. 2014–00102 Filed 1–7–14; 8:45 am]
As discussed above, these proposed
special conditions apply to Airbus
Model A350–900 series airplanes.
Should Airbus apply later for a change
to the type certificate to include another
model incorporating the same novel or
unusual design feature, the proposed
special conditions would apply to that
model as well under the provisions of
§ 21.101.
VerDate Mar<15>2010
Authority: 49 U.S.C. 106(g), 40113, 44701,
44702, 44704.
PO 00000
Frm 00003
Fmt 4702
Sfmt 4702
that the Administrator considers
necessary to establish a level of safety
equivalent to that established by the
existing airworthiness standards.
DATES: Send your comments on or
before February 7, 2014.
ADDRESSES: Send comments identified
by docket number FAA–2013–0901
using any of the following methods:
• Federal eRegulations Portal: Go to
https://www.regulations.gov/ and follow
the online instructions for sending your
comments electronically.
• Mail: Send comments to Docket
Operations, M–30, U.S. Department of
Transportation (DOT), 1200 New Jersey
Avenue SE., Room W12–140, West
Building Ground Floor, Washington, DC
20590–0001.
• Hand Delivery or Courier: Take
comments to Docket Operations in
Room W12–140 of the West Building
Ground Floor at 1200 New Jersey
Avenue SE., Washington, DC., between
9 a.m. and 5 p.m., Monday through
Friday, except federal holidays.
• Fax: Fax comments to Docket
Operations at 202–493–2251.
Privacy: The FAA will post all
comments it receives, without change,
to https://www.regulations.gov/,
including any personal information the
commenter provides. Using the search
function of the docket Web site, anyone
can find and read the electronic form of
all comments received into any FAA
docket, including the name of the
individual sending the comment (or
signing the comment for an association,
business, labor union, etc.). DOT’s
complete Privacy Act Statement can be
found in the Federal Register published
on April 11, 2000 (65 FR 19477–19478),
as well as at https://DocketsInfo.
dot.gov/.
Docket: Background documents or
comments received may be read at
https://www.regulations.gov/ at any time.
Follow the online instructions for
accessing the docket or go to the Docket
Operations in Room W12–140 of the
West Building Ground Floor at 1200
New Jersey Avenue SE., Washington,
DC, between 9 a.m. and 5 p.m., Monday
through Friday, except federal holidays.
FOR FURTHER INFORMATION CONTACT: Joe
Jacobsen, FAA, Airplane and Flightcrew
Interface Branch, ANM–111, Transport
Airplane Directorate, Aircraft
Certification Service, 1601 Lind Avenue
SW., Renton, Washington 98057–3356;
telephone (425) 227–2011; facsimile
(425) 227–1320.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite interested people to take
part in this rulemaking by sending
E:\FR\FM\08JAP1.SGM
08JAP1
Federal Register / Vol. 79, No. 5 / Wednesday, January 8, 2014 / Proposed Rules
written comments, data, or views. The
most helpful comments reference a
specific portion of the special
conditions, explain the reason for any
recommended change, and include
supporting data.
We will consider all comments we
receive on or before the closing date for
comments. We may change these special
conditions based on the comments we
receive.
Background
On August 25, 2008, Airbus applied
for a type certificate for their new Model
A350–900 series airplane. Later, Airbus
requested and the FAA approved an
extension to the application for FAA
type certification to June 28, 2009. The
Model A350–900 series has a
conventional layout with twin wingmounted Rolls-Royce Trent engines. It
features a twin aisle 9-abreast economy
class layout, and accommodates side-byside placement of LD–3 containers in
the cargo compartment. The basic
Model A350–900 series configuration
will accommodate 315 passengers in a
standard two-class arrangement. The
design cruise speed is Mach 0.85 with
a Maximum Take-Off Weight of 602,000
lbs. Airbus proposes the Model A350–
900 series to be certified for extended
operations (ETOPS) beyond 180 minutes
at entry into service for up to a 420minute maximum diversion time.
The longitudinal control law design of
the Airbus Model A350–900
incorporates an overspeed protection
system in the normal mode; this would
prevent the pilot from inadvertently or
intentionally exceeding a speed
approximately equivalent to VFC or
attaining VDF. Current Title 14 Code of
Federal Regulations (14 CFR) part 25
sections do not relate to a high speed
limiting protection system that might
preclude or modify flying qualities
assessments in the overspeed region.
However, the requirements of § 25.253
(High-speed characteristics) and its
related policy are applicable to the
Model A350–900 series and not affected
by this proposed special condition.
mstockstill on DSK4VPTVN1PROD with PROPOSALS
Type Certification Basis
Under Title 14, Code of Federal
Regulations (14 CFR) 21.17, Airbus must
show that the Model A350–900 series
meets the applicable provisions of 14
CFR part 25, as amended by
Amendments 25–1 through 25–129.
If the Administrator finds that the
applicable airworthiness regulations
(i.e., 14 CFR part 25) do not contain
adequate or appropriate safety standards
for the Airbus Model A350–900 series
because of a novel or unusual design
VerDate Mar<15>2010
16:18 Jan 07, 2014
Jkt 232001
feature, special conditions are
prescribed under § 21.16.
Special conditions are initially
applicable to the model for which they
are issued. Should the type certificate
for that model be amended later to
include any other model that
incorporates the same or similar novel
or unusual design feature, the special
conditions would also apply to the other
model under § 21.101.
In addition to the applicable
airworthiness regulations and proposed
special conditions, the Model A350–900
series must comply with the fuel vent
and exhaust emission requirements of
14 CFR part 34 and the noise
certification requirements of 14 CFR
part 36 and the FAA must issue a
finding of regulatory adequacy under
section 611 of Public Law 92–574, the
‘‘Noise Control Act of 1972.’’
The FAA issues special conditions, as
defined in 14 CFR 11.19, under § 11.38,
and they become part of the typecertification basis under § 21.17(a)(2).
Novel or Unusual Design Features
The Model A350–900 series will
incorporate the following novel or
unusual design features: An overspeed
protection system which prevents the
pilot from inadvertently or intentionally
exceeding a speed approximately
equivalent to VFC or attaining VDF.
At VMO + 10 knots or MMO + 0.02, an
automatic nose up pitch is applied with
phase advance in case of high
acceleration. The speed stabilizes at VD
¥ 10kts/MD ¥ 0.02 if the stick is full
forward, or the speed will return below
VMO/MMO if the stick is released.
Discussion
This proposed special condition
establishes requirements to ensure that
operation of the high speed limiting
protection system does not impede
normal attainment of speeds up to the
overspeed warning. Its main features
are:
1. It protects the airplane against high
speed/high Mach number flight
conditions beyond VMO/MMO.
2. It does not interfere with flight at
VMO/MMO, even in turbulent air.
3. It still provides load factor
limitation through the ‘‘pitch limiting’’
function described below.
4. It restores positive static stability
beyond VMO/MMO.
Applicability
As discussed above, these proposed
special conditions apply to Airbus
Model A350–900 series airplanes.
Should Airbus apply later for a change
to the type certificate to include another
model incorporating the same novel or
PO 00000
Frm 00004
Fmt 4702
Sfmt 4702
1337
unusual design feature, the proposed
special conditions would apply to that
model as well.
Conclusion
This action affects only certain novel
or unusual design features on the Airbus
Model A350–900 series airplanes. It is
not a rule of general applicability.
List of Subjects in 14 CFR Part 25
Aircraft, Aviation safety, Reporting
and recordkeeping requirements.
The authority citation for these
special conditions is as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701,
44702, 44704.
The Proposed Special Conditions
Accordingly, the Federal Aviation
Administration (FAA) proposes the
following special condition as part of
the type certification basis for Airbus
Model A350–900 series airplanes.
In addition to § 25.143, the following
requirements apply: Operation of the
high speed limiter during all routine
and descent procedure flight must not
impede normal attainment of speeds up
to overspeed warning
Issued in Renton, Washington, on October
22, 2013.
Stephen P. Boyd,
Acting Manager, Transport Airplane
Directorate, Aircraft Certification Service.
[FR Doc. 2014–00100 Filed 1–7–14; 8:45 am]
BILLING CODE 4910–13–P
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 25
[Docket No. FAA–2013–0892; Notice
No. 25–13–21–SC]
Special Conditions: Airbus, A350–900
Series Airplane; Crashworthiness—
Emergency Landing Conditions
Federal Aviation
Administration (FAA), DOT.
ACTION: Notice of proposed special
conditions.
AGENCY:
This action proposes special
conditions for the Airbus Model A350–
900 series airplanes. These airplanes
will have a novel or unusual design
feature associated with crashworthiness
of carbon fiber reinforced plastic used in
the construction of the fuselage. The
applicable airworthiness regulations do
not contain adequate or appropriate
safety standards for this design feature.
These proposed special conditions
contain the additional safety standards
that the Administrator considers
SUMMARY:
E:\FR\FM\08JAP1.SGM
08JAP1
Agencies
[Federal Register Volume 79, Number 5 (Wednesday, January 8, 2014)]
[Proposed Rules]
[Pages 1336-1337]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2014-00100]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 25
[Docket No. FAA-2013-0901; Notice No. 25-13-23-SC]
Special Conditions: Airbus, Model A350-900 Series Airplane;
Flight Envelope Protection: High Speed Limiting
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed special conditions.
-----------------------------------------------------------------------
SUMMARY: This action proposes special conditions for Airbus Model A350-
900 series airplanes. These airplanes will have a novel or unusual
design feature associated with high speed limiting. The applicable
airworthiness regulations do not contain adequate or appropriate safety
standards for this design feature. These proposed special conditions
contain the additional safety standards that the Administrator
considers necessary to establish a level of safety equivalent to that
established by the existing airworthiness standards.
DATES: Send your comments on or before February 7, 2014.
ADDRESSES: Send comments identified by docket number FAA-2013-0901
using any of the following methods:
Federal eRegulations Portal: Go to https://www.regulations.gov/ and follow the online instructions for sending
your comments electronically.
Mail: Send comments to Docket Operations, M-30, U.S.
Department of Transportation (DOT), 1200 New Jersey Avenue SE., Room
W12-140, West Building Ground Floor, Washington, DC 20590-0001.
Hand Delivery or Courier: Take comments to Docket
Operations in Room W12-140 of the West Building Ground Floor at 1200
New Jersey Avenue SE., Washington, DC., between 9 a.m. and 5 p.m.,
Monday through Friday, except federal holidays.
Fax: Fax comments to Docket Operations at 202-493-2251.
Privacy: The FAA will post all comments it receives, without
change, to https://www.regulations.gov/, including any personal
information the commenter provides. Using the search function of the
docket Web site, anyone can find and read the electronic form of all
comments received into any FAA docket, including the name of the
individual sending the comment (or signing the comment for an
association, business, labor union, etc.). DOT's complete Privacy Act
Statement can be found in the Federal Register published on April 11,
2000 (65 FR 19477-19478), as well as at https://DocketsInfo.dot.gov/.
Docket: Background documents or comments received may be read at
https://www.regulations.gov/ at any time. Follow the online instructions
for accessing the docket or go to the Docket Operations in Room W12-140
of the West Building Ground Floor at 1200 New Jersey Avenue SE.,
Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday,
except federal holidays.
FOR FURTHER INFORMATION CONTACT: Joe Jacobsen, FAA, Airplane and
Flightcrew Interface Branch, ANM-111, Transport Airplane Directorate,
Aircraft Certification Service, 1601 Lind Avenue SW., Renton,
Washington 98057-3356; telephone (425) 227-2011; facsimile (425) 227-
1320.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite interested people to take part in this rulemaking by
sending
[[Page 1337]]
written comments, data, or views. The most helpful comments reference a
specific portion of the special conditions, explain the reason for any
recommended change, and include supporting data.
We will consider all comments we receive on or before the closing
date for comments. We may change these special conditions based on the
comments we receive.
Background
On August 25, 2008, Airbus applied for a type certificate for their
new Model A350-900 series airplane. Later, Airbus requested and the FAA
approved an extension to the application for FAA type certification to
June 28, 2009. The Model A350-900 series has a conventional layout with
twin wing-mounted Rolls-Royce Trent engines. It features a twin aisle
9-abreast economy class layout, and accommodates side-by-side placement
of LD-3 containers in the cargo compartment. The basic Model A350-900
series configuration will accommodate 315 passengers in a standard two-
class arrangement. The design cruise speed is Mach 0.85 with a Maximum
Take-Off Weight of 602,000 lbs. Airbus proposes the Model A350-900
series to be certified for extended operations (ETOPS) beyond 180
minutes at entry into service for up to a 420-minute maximum diversion
time.
The longitudinal control law design of the Airbus Model A350-900
incorporates an overspeed protection system in the normal mode; this
would prevent the pilot from inadvertently or intentionally exceeding a
speed approximately equivalent to VFC or attaining
VDF. Current Title 14 Code of Federal Regulations (14 CFR)
part 25 sections do not relate to a high speed limiting protection
system that might preclude or modify flying qualities assessments in
the overspeed region. However, the requirements of Sec. 25.253 (High-
speed characteristics) and its related policy are applicable to the
Model A350-900 series and not affected by this proposed special
condition.
Type Certification Basis
Under Title 14, Code of Federal Regulations (14 CFR) 21.17, Airbus
must show that the Model A350-900 series meets the applicable
provisions of 14 CFR part 25, as amended by Amendments 25-1 through 25-
129.
If the Administrator finds that the applicable airworthiness
regulations (i.e., 14 CFR part 25) do not contain adequate or
appropriate safety standards for the Airbus Model A350-900 series
because of a novel or unusual design feature, special conditions are
prescribed under Sec. 21.16.
Special conditions are initially applicable to the model for which
they are issued. Should the type certificate for that model be amended
later to include any other model that incorporates the same or similar
novel or unusual design feature, the special conditions would also
apply to the other model under Sec. 21.101.
In addition to the applicable airworthiness regulations and
proposed special conditions, the Model A350-900 series must comply with
the fuel vent and exhaust emission requirements of 14 CFR part 34 and
the noise certification requirements of 14 CFR part 36 and the FAA must
issue a finding of regulatory adequacy under section 611 of Public Law
92-574, the ``Noise Control Act of 1972.''
The FAA issues special conditions, as defined in 14 CFR 11.19,
under Sec. 11.38, and they become part of the type-certification basis
under Sec. 21.17(a)(2).
Novel or Unusual Design Features
The Model A350-900 series will incorporate the following novel or
unusual design features: An overspeed protection system which prevents
the pilot from inadvertently or intentionally exceeding a speed
approximately equivalent to VFC or attaining VDF.
At VMO + 10 knots or MMO + 0.02, an automatic
nose up pitch is applied with phase advance in case of high
acceleration. The speed stabilizes at VD - 10kts/
MD - 0.02 if the stick is full forward, or the speed will
return below VMO/MMO if the stick is released.
Discussion
This proposed special condition establishes requirements to ensure
that operation of the high speed limiting protection system does not
impede normal attainment of speeds up to the overspeed warning. Its
main features are:
1. It protects the airplane against high speed/high Mach number
flight conditions beyond VMO/MMO.
2. It does not interfere with flight at VMO/
MMO, even in turbulent air.
3. It still provides load factor limitation through the ``pitch
limiting'' function described below.
4. It restores positive static stability beyond VMO/
MMO.
Applicability
As discussed above, these proposed special conditions apply to
Airbus Model A350-900 series airplanes. Should Airbus apply later for a
change to the type certificate to include another model incorporating
the same novel or unusual design feature, the proposed special
conditions would apply to that model as well.
Conclusion
This action affects only certain novel or unusual design features
on the Airbus Model A350-900 series airplanes. It is not a rule of
general applicability.
List of Subjects in 14 CFR Part 25
Aircraft, Aviation safety, Reporting and recordkeeping
requirements.
The authority citation for these special conditions is as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701, 44702, 44704.
The Proposed Special Conditions
Accordingly, the Federal Aviation Administration (FAA) proposes the
following special condition as part of the type certification basis for
Airbus Model A350-900 series airplanes.
In addition to Sec. 25.143, the following requirements apply:
Operation of the high speed limiter during all routine and descent
procedure flight must not impede normal attainment of speeds up to
overspeed warning
Issued in Renton, Washington, on October 22, 2013.
Stephen P. Boyd,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2014-00100 Filed 1-7-14; 8:45 am]
BILLING CODE 4910-13-P