Architectural Barriers Act Accessibility Guidelines; Outdoor Developed Areas, 59475-59553 [2013-22876]

Download as PDF Vol. 78 Thursday, No. 187 September 26, 2013 Part III Architectural and Transportation Barriers Compliance Board emcdonald on DSK67QTVN1PROD with RULES2 36 CFR Part 1191 Architectural Barriers Act Accessibility Guidelines; Outdoor Developed Areas; Final Rule VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 PO 00000 Frm 00001 Fmt 4717 Sfmt 4717 E:\FR\FM\26SER2.SGM 26SER2 59476 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 4. Changes Made to the Proposed Rule 5. Discussion of Scoping and Technical Requirements 6. Regulatory Analyses ARCHITECTURAL AND TRANSPORTATION BARRIERS COMPLIANCE BOARD 36 CFR Part 1191 RIN 3014–AA22 Architectural Barriers Act Accessibility Guidelines; Outdoor Developed Areas Architectural and Transportation Barriers Compliance Board. ACTION: Final rule. AGENCY: We, the Architectural and Transportation Barriers Compliance Board (Access Board), are issuing a final rule that amends the Architectural Barriers Act Accessibility Guidelines by adding scoping and technical requirements for camping facilities, picnic facilities, viewing areas, trails, and beach access routes constructed or altered by or on behalf of federal agencies. The final rule ensures that these facilities are readily accessible to and usable by individuals with disabilities. The final rule applies to the following federal agencies and their components that administer outdoor areas developed for recreational purposes: Department of Agriculture (Forest Service); Department of Defense (Army Corps of Engineers); and Department of the Interior (Bureau of Land Management, Bureau of Reclamation, Fish and Wildlife Service, National Park Service). The final rule also applies to non-federal entities that construct or alter recreation facilities on federal land on behalf of the federal agencies pursuant to a concession contract, partnership agreement, or similar arrangement. DATES: The final rule is effective November 25, 2013. The incorporation of certain publications listed in the guidelines is approved by the Director of the Federal Register as of September 21, 2004. FOR FURTHER INFORMATION CONTACT: William Botten, Access Board, 1331 F Street NW., Suite 1000, Washington, DC 20004–1111. Telephone: (202) 272–0014 (voice) or (202) 272–0082 (TTY). Email address: botten@access-board.gov. SUPPLEMENTARY INFORMATION: SUMMARY: emcdonald on DSK67QTVN1PROD with RULES2 Table of Contents for Preamble 1. New Format for Guidelines 2. Executive Summary 3. Statutory and Regulatory Background VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 In this preamble, ‘‘we,’’ ‘‘our’’ and ‘‘us’’ refer to the Architectural and Transportation Barriers Compliance Board (Access Board). 1. New Format for Guidelines This final rule amends the Architectural Barriers Act Accessibility Guidelines, which were published in the Federal Register on July 23, 2004 (69 FR 44151) and are codified in Appendices C and D to 36 CFR part 1191. The guidelines were published as ‘‘camera ready’’ copy (i.e., images) in 2004 because they included figures after certain sections to illustrate technical requirements in the sections. Since it is not possible to amend the guidelines as published in 2004, we submitted the guidelines, as amended by the final rule, to the Federal Register as a Word document without figures, except for four mandatory symbols included at the end of Appendix D.1 The scoping requirements for the Americans with Disabilities Act Accessibility Guidelines in Appendix B are not changed. We did not include advisory sections that previously appeared in Appendices B, C, and D because they provide guidance only and do not contain mandatory requirements. We removed the List of Figures and Index in Appendix E because it did not contain regulatory material. We added notes to paragraphs (a) and (b) of section 1191.1 that reference the accessibility standards adopted by the Department of Justice and Department of Defense. Advisory sections and figures are included in the documents on our Web page at: www.access-board.gov. 2. Executive Summary Legal Authority and Purpose The Architectural Barriers Act requires facilities constructed or altered by or on behalf of federal agencies to be readily accessible to and usable by individuals with disabilities. Certain agencies are required to adopt accessibility standards for the design, construction, and alteration of facilities 1 The four mandatory symbols are the: Symbols to identify elevator control buttons (Figure 407.4.7.13); International Symbol of Accessibility (Figure 703.7.2.1); International Symbol of TTY (Figure 703.7.2.2); and International Symbol of Access for Hearing Loss (Figure 703.7.2.4). PO 00000 Frm 00002 Fmt 4701 Sfmt 4700 covered by the Architectural Barriers Act.2 We are required by section 502 of the Rehabilitation Act to establish and maintain minimum guidelines and requirements for the accessibility standards adopted the federal agencies. We are issuing the final rule pursuant to this authority. The final rule amends the Architectural Barriers Act Accessibility Guidelines that we issued in 2004 to address camping facilities, picnic facilities, viewing areas, trails, and beach access routes constructed or altered by or behalf of federal agencies. Summary of Major Provisions The final rule applies to the following federal agencies and their components that administer outdoor areas developed for recreational purposes: Department of Agriculture (Forest Service); Department of Defense (Army Corps of Engineers); and Department of the Interior (Bureau of Land Management, Bureau of Reclamation, Fish and Wildlife Service, National Park Service). The final rule also applies to non-federal entities that construct or alter recreation facilities on federal land on behalf of the federal agencies pursuant to a concession contract, partnership agreement, or similar arrangement. The final rule adds scoping and technical requirements for the design, construction, and alteration of camping facilities, picnic facilities, viewing areas, trails, and beach access routes to the Architectural Barriers Act Accessibility Guidelines. The scoping requirements address the following outdoor constructed features provided at these facilities: Picnic tables, fire rings, grills, fireplaces, wood stoves, trash and recycling receptacles, water hydrants, utility and sewage hookups, outdoor rinsing showers, benches, and viewing scopes. The scoping requirements also address the following elements provided in camping units with mobility features: Parking spaces for recreational vehicles and other vehicles; tent pads and tent platforms; and camp shelters. The scoping requirements added by the final rule are summarized in Table 1. 2 The Architectural Barriers Act requires the following agencies to adopt accessibility standards: Department of Defense and United States Postal Service for their facilities; Department of Housing and Urban Development for residential facilities; and General Services Administration for all other facilities. E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 59477 TABLE 1—SCOPING REQUIREMENTS ADDED BY FINAL RULE F244 F245 Camping Facilities ................................ Picnic Facilities. F246 Viewing Areas ....................................... F216.13 Trailhead Signs ................................ F247 Trails. F248 Beach Access Routes .......................... The technical requirements establish design criteria for outdoor constructed features; parking spaces within camping units and picnic units with mobility features; pull-up spaces for recreational vehicles at dump stations; tent pads and Requires minimum number of camping units and picnic units to provide mobility features based on total number of units provided in the camping or picnic facility. Requires camping units and picnic units with mobility features to provide choices of units comparable to, and integrated with, those available to others. Requires at least one of each type of outdoor constructed features and other elements provided within camping units and picnic units with mobility features to comply with the applicable technical requirements. Where more than one of the same type of outdoor constructed feature or element is provided, requires at least two of the same type to comply with the applicable technical requirements. Requires at least 20 percent of each type of outdoor constructed features provided at each location in common use and public use areas serving camping units and picnic units with mobility features to comply with the applicable technical requirements. Requires outdoor recreation access routes to connect: • Accessible elements, spaces, and facilities provided within camping units and picnic units with mobility features; • Camping units and picnic units with mobility features to common use and public use areas serving the units; • Accessible elements, spaces, and facilities provided within common use and public use areas serving camping units and picnic units with mobility features; and • Camping units and picnic units with mobility features to an accessible route serving adjacent recreation facilities, where a circulation path connects camping and picnic facilities and adjacent recreation facilities. Requires each distinct viewing location and at least 20 percent of outdoor constructed features within viewing areas to comply with the applicable technical requirements. Requires outdoor recreation access routes to connect accessible parking spaces or other arrival points serving the viewing area with accessible elements, spaces, and facilities provided within the viewing area. Requires new trail information signs provided at trailheads on newly constructed and altered trails designed for use by hikers or pedestrians to comply with the applicable technical requirements for trailhead signs. Requires trails designed for use by hikers and pedestrians to comply with the applicable technical requirements for trails where the trail directly connects to a trailhead or another trail that substantially meets the applicable technical requirements for trails. Requires existing trails to comply with the applicable technical requirements for trails where the original design, function, or purpose of the trail is changed and the altered portion of the trail directly connects to a trailhead or another trail that substantially meets the applicable technical requirements for trails. Requires camping facilities, picnic facilities, and viewing areas provided on trails to comply with the applicable scoping requirements in F244, F245, and F246, except for outdoor recreation access routes. Requires at least 20 percent of outdoor constructed features provided at trailheads and at each location on trails, other than at facilities provided on trails, to comply with the applicable technical requirements. Requires outdoor recreation access routes to connect accessible parking spaces or other arrival points serving a trailhead to the starting point of the trail and accessible elements, spaces, and facilities provided within the trailhead. Requires at least one permanent or removable beach access route to be provided for each 1/2 mile of beach shoreline administered or managed by an entity where: • Circulation paths, parking facilities, toilet facilities, or bathing facilities serving the beach are constructed or altered; or • A beach nourishment project is undertaken. Not more than 20 percent of the costs of constructing or altering facilities serving the beach or a beach nourishment project are required to be expended on beach access routes. tent platforms; camp shelters; viewing areas; outdoor recreation access routes; trails; and beach access routes. The final rule permits exceptions to specific provisions in the technical requirements for certain elements and facilities based on the conditions listed in Table 2. When an entity determines that a condition does not permit full compliance with a provision, compliance is required to the extent practicable. emcdonald on DSK67QTVN1PROD with RULES2 TABLE 2—CONDITIONS FOR EXCEPTIONS 1 ................................... 2 ................................... 3 ................................... VerDate Mar<15>2010 Compliance is not practicable due to terrain. Compliance cannot be accomplished with the prevailing construction practices. Compliance would fundamentally alter the function or purpose of the facility or the setting. 18:25 Sep 25, 2013 Jkt 229001 PO 00000 Frm 00003 Fmt 4701 Sfmt 4700 E:\FR\FM\26SER2.SGM 26SER2 59478 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations TABLE 2—CONDITIONS FOR EXCEPTIONS—Continued 4 ................................... Compliance is limited or precluded by any of the following laws, or by decisions or opinions issued or agreements executed pursuant to any of the following laws: Endangered Species Act; National Environmental Policy Act; National Historic Preservation Act; Wilderness Act; or other federal, state, or local law the purpose of which is to preserve threatened or endangered species; the environment; or archaeological, cultural, historical, or other significant natural features. The final rule allows exemptions for an entire trail or beach access route when an entity determines that is impracticable for a trail to comply with the technical requirements for trails or to provide a beach access route complying with the technical requirements for beach access routes. This determination is made after the entity applies the exceptions for specific provisions in the technical requirements for trails or beach access routes to portions of the trail or route. Summary of Costs and Benefits We compared the final rule to guidelines and standards used by the federal agencies for the design of outdoor developed areas without regard to accessibility to determine whether the final rule would result in additional costs. We determined the final rule would not result in additional costs for camping facilities and picnic facilities. We estimate the final rule would result in additional costs for viewing areas, trails, and beach access routes shown in Table 3. We estimate the federal agencies would incur $1.2 million additional annual costs due to the final rule. TABLE 3—ADDITIONAL COSTS DUE TO FINAL RULE Viewing Areas ......................................... Trails ........................................................ Beach Access Routes ............................. $2,176 for dual base binocular scopes and $3,380 for a dual base telescopes, if viewing scopes provided at viewing areas. $40,655 per trail mile, if trail would not otherwise meet the technical requirements and the exceptions to the technical requirements do not apply to the trail. $4,497 to $6,530 to purchase roll-out mats for beach access routes, if parking areas, toilet facilities, bathing facilities, and circulation paths serving beaches are constructed or altered or beach nourishment project is undertaken. The proposed rule would enable individuals with mobility disabilities to participate in outdoor recreation activities with their families and friends. The benefits are difficult to quantify, but include important national values recognized in Executive Order 13563 such as equity, human dignity, and fairness. 3. Statutory and Regulatory Background The Architectural Barriers Act requires facilities constructed or altered by or on behalf of federal agencies to be readily accessible to and usable by individuals with disabilities.3 See 42 U.S.C. 4151 et seq. The Department of Defense, Department of Housing and Urban Development, General Services Administration, and United States Postal Service are required to adopt accessibility standards for the design, construction, and alteration of facilities covered by the Architectural Barriers Act.4 See 42 U.S.C. 4152 through 4154a. emcdonald on DSK67QTVN1PROD with RULES2 3 The Architectural Barriers Act also covers facilities leased by federal agencies; facilities financed by a federal grant or loan; and facilities constructed by the Washington Metropolitan Area Transit Authority. The final rule does not apply to these facilities. 4 The Department of Defense and United States Postal Service are required to adopt accessibility standards for their facilities; the Department of Housing and Urban Development is required to adopt accessibility standards for residential facilities; and the General Services Administration is required to adopt accessibility standards for all VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 We are required by section 502 of the Rehabilitation Act to establish and maintain minimum guidelines and requirements for the accessibility standards adopted the federal agencies. See 29 U.S.C. 792(b)(3). We also are required by section 502 of the Rehabilitation Act to investigate complaints alleging that facilities covered by the Architectural Barriers Act have not complied with the accessibility standards. See 29 U.S.C. 792(b)(1) and (e). When we find a violation, we request the responsible federal agency to submit a corrective action plan and monitor implementation of the plan. We issued the Architectural Barriers Act Accessibility Guidelines for facilities covered by the Architectural Barriers Act in 2004. See 69 FR 44151 (July 23, 2004). The guidelines contain scoping and technical requirements. Scoping requirements specify what features are required to be accessible and, where multiple features of the same type are provided, how many of the features are required to be accessible. Technical requirements specify the design criteria for accessible features. The scoping and technical requirements address some but not all of the features provided at outdoor areas developed for recreation purposes. For example, the scoping and technical other facilities covered by the Architectural Barriers Act. PO 00000 Frm 00004 Fmt 4701 Sfmt 4700 requirements address parking areas, toilet and bathing facilities, fishing piers and platforms, and boating docks and marinas. However, the scoping and technical requirements do not address the minimum number of camping units and picnic units required to provide mobility features, or provide design criteria for viewing areas, trails, and beach access routes. The final rule amends the guidelines by adding scoping and technical requirements for these features. The Architectural Barriers Act Accessibility Guidelines are codified at Appendices C and D to 36 CFR part 1191. The Department of Defense, United States Postal Service, and General Services Administration adopted the Architectural Barriers Act Accessibility Guidelines as the accessibility standards for facilities covered by the Architectural Barriers Act Guidelines by cross-referencing Appendices C and D.5 Since these 5 The Department of Defense cross references Appendices C and D as the accessibility standards for its facilities in a Memorandum on Access for People with Disabilities (October 31, 2008) at: https://www.access-board.gov/guidelines-andstandards/buildings-and-sites/about-the-abastandards/background/dod-memorandum. The United States Postal Service cross references Appendices C and D as the accessibility standards for its facilities at 39 CFR 254.1. The General Services Administration cross references Appendices C and D as the accessibility standards for all other facilities, except residential facilities, covered by the Architectural Barriers Act at 41 CFR E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations agencies cross-reference Appendices C and D, the amendments to Appendices C and D made by the final rule are incorporated into the accessibility standards for facilities covered by the Architectural Barriers Act. Thus, camping facilities, picnic facilities, viewing areas, trails, and beach access routes constructed or altered by or on behalf of federal agencies on or after the effective date of the final rule are required to comply with Appendices C and D, as amended by the final rule. The final rule does not apply to outdoor developed areas administered by state and local governments and by private entities covered by Titles II and III the Americans with Disabilities Act because sufficient data were not available to prepare a regulatory assessment of the impact of the proposed rule on state and local governments or private entities. We will conduct a separate rulemaking in the future for outdoor developed areas administered by state and local governments and by private entities covered by the Titles II and III of the Americans with Disabilities Act.6 4. Changes Made to the Proposed Rule We issued a proposed rule in 2007. See 72 FR 34074 (June 20, 2007). The proposed rule was based on the report of a regulatory negotiation committee. We released a draft of the final rule in 2009. The regulatory negotiation report, proposed rule, and draft of the final rule are available on our Web site at: https:// www.access-board.gov/outdoor (click on Background). The changes made to the proposed rule are discussed below. emcdonald on DSK67QTVN1PROD with RULES2 Format and Organization The proposed rule would have established the scoping and technical requirements for camping facilities, picnic facilities, viewing areas, trails, and beach access routes as separate guidelines to be codified as an appendix to 36 CFR part 1195. The final rule incorporates the scoping and technical requirements for these facilities into the Architectural Barriers Act Accessibility Guidelines, which are codified as Appendices C and D to 36 CFR part 1191. 102–76.65. The Department of Housing and Urban Development references the Uniform Federal Accessibility Standards, which was issued in 1984, as the accessibility standards for residential facilities covered by the Architectural Barriers Act. See 24 CFR 40.4. 6 We are required to establish and maintain minimum guidelines and requirements for the accessibility standards adopted by the Department of Justice and Department of Transportation for facilities covered by Titles II and III of the Americans with Disabilities Act. See 29 U.S.C. 792 (b)(3) and 42 U.S.C. 12204. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 Exceptions When Conditions Do Not Permit Full Compliance The proposed rule would have permitted exceptions to only certain provisions in the technical requirements when certain conditions do not permit full compliance. The final rule restates the conditions as shown in the Table 2 under the Executive Summary, and permits exceptions based on the conditions to any provision in the technical requirements for tent pads and tent platforms, camp shelters, viewing areas, outdoor recreation access routes, trails, and beach access routes.7 The final rule also permits exceptions based on the conditions to the provisions for clear ground space at outdoor constructed features in alterations. The proposed rule would have required compliance ‘‘to the maximum extent feasible’’ when an exception is used. The final rule requires compliance ‘‘to the extent practicable’’ when an exception is used. This language is more in keeping with the regulatory negotiation committee report, which considered the term ‘‘feasible’’ to mean ‘‘reasonably-doable.’’ The regulatory negotiation committee report used the example of constructing a portion of a trail in a steeply sloped area, where complying with the provision for running slope would require extensive cuts and fills that would be difficult to construct and maintain; cause drainage and erosion problems; and have a severe impact on the environment. In this example, the portion of the trail constructed in the steeply sloped area is permitted to comply with the provision for running slope to the extent practicable. When an exception to a specific provision in the technical requirements is used on a portion of a trail or beach access route, the final rule requires the federal agency to document the basis for its determination to use the exception and to maintain the documentation in the records for the trail or beach project in the event that a complaint is later filed alleging that the trail or beach access route does not fully comply with the applicable technical requirements. When investigating the complaint, we will request the federal agency to provide the documentation if the federal agency claims that it used an exception based on the conditions. 7 Exceptions are permitted to the technical requirements for viewing areas and for outdoor recreation access routes at camping facilities, picnic facilities, and trailheads only in alterations. PO 00000 Frm 00005 Fmt 4701 Sfmt 4700 59479 Exemptions for Entire Trail or Beach Access Route The proposed rule would have exempted an entire trail from complying with the technical requirements for trails when: • The combination of running slope and cross slope exceeds 40 percent for over 20 feet; • A trail obstacle 30 inches high or more runs across the full tread width of the trail; • The trail surface is neither firm nor stable for a distance of 45 feet or more; • The tread width is less than 12 inches wide for a distance of 20 feet or more; or • The trail is not required to comply with any of the technical requirements for more than 15 percent of the trail. The final rule allows an entire trail to be exempted when an entity determines that it would be impracticable for the trail to comply with the technical requirements for trails. This determination is made after the entity applies the exceptions for specific provisions in the technical requirements for trails to portions of the trail. The exemption is intended to allow for conditions in the field other than those listed in the proposed rule that may render it impracticable for the trail to comply with the technical requirements for trails. The final rule requires federal agencies to notify us if an entire trail is exempted. A form to notify us is available at: https://www.accessboard.gov/outdoor. The form lists the conditions in the proposed rule as a basis for exempting an entire trail and allows other conditions in the field to also be a basis for exempting an entire trail. The form will allow us to monitor exemptions and to provide guidance as necessary. The proposed rule did not include an exemption for an entire beach access route. The final rule does not require a beach access route to be provided when an entity determines that it would be impracticable to provide a beach access route complying with the technical provisions for beach access routes. This determination is made after the entity applies the exceptions for specific provisions in the technical requirements for beach access routes to portions of the route. The final rule requires federal agencies to notify us if a beach access route is not provided. A form to notify us is available at: https://www.accessboard.gov/guidelines-and-standards/ recreation-facilities/outdoor-developedareas. Beach Access Routes The proposed rule would have required beach access routes to be E:\FR\FM\26SER2.SGM 26SER2 59480 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations provided where a beach is constructed and where a pedestrian route is constructed at a beach. The final rule requires beach access routes to be provided where the entity that administers or manages a beach constructs or alters circulation paths, parking facilities, toilet facilities, or bathing facilities to serve the beach or undertakes a beach nourishment project. The entity is not required to expend more than 20 percent of the costs of constructing or altering facilities serving the beach or the beach nourishment project to provide beach access routes. The proposed rule would have required the clear width of beach access routes to be 36 inches minimum. Beach access routes provide a firm and stable surface over the sand and are used by beach visitors with and without disabilities. The final rule requires the clear width of beach access routes to be 60 inches minimum to enable individuals who use wheeled mobility devices to pass beach visitors traveling in the opposite direction. emcdonald on DSK67QTVN1PROD with RULES2 Shared Use Paths The preamble to the proposed rule indicated that the proposed scoping and technical requirements for trails would apply to shared use paths. A shared use path is a multi-use path that is designed primarily for use by pedestrians and bicyclists for transportation and recreational purposes. Shared use paths are physically separated from motor vehicle traffic by an open space or barrier, and are either within the highway right-of-way or within an independent right-of-way. We subsequently decided to include shared use paths in the proposed accessibility guidelines for pedestrian facilities in the public right-of-way. See 78 FR 10110 (February 13, 2013). Trailhead Signs The proposed rule would have required signs to be provided at trailheads to identify accessible trails. The proposed rule would have required the signs to include information on the total distance of the trail and, where exceptions have been used, the location of the first point where the trail does not fully comply with the technical requirements for trails. Where new trail information signs are provided at trailheads on newly constructed or altered trails designed for use by hikers or pedestrians, the final rule requires the signs to include information on the length of the trail or trail segment; surface type; typical and minimum tread width; typical and maximum running slope; and typical and maximum cross slope. This VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 requirement applies regardless of whether the trail complies with the technical requirements for trails. The information provided on the signs enables individuals with disabilities to decide whether to hike the trail based on the characteristics of the trail. Surface Slopes The proposed rule would have required clear ground spaces to have slopes not steeper than 1:50 in any direction, and would have permitted slopes not steeper than 1:33 when necessary for drainage. The final rule requires clear ground spaces to have slopes not steeper than 1:48 in any direction and, where the surface is other than concrete, asphalt, or boards, permits slopes not steeper than 1:20 when necessary for drainage. The final rule defines the term boards to include wood, plastic, metal, and composite products. The proposed rule would have required outdoor recreation access routes and beach access routes to have cross slopes not steeper than 1:33, and would have permitted cross slopes not steeper than 1:20 when necessary for drainage. The proposed rule would have required trails to have cross slopes not steeper than 1:20. The final rule requires outdoor recreation access routes, trails, and beach access routes to have cross slopes not steeper than 1:48 and, where the surface is other than concrete, asphalt, or boards, permits cross slopes not steeper than 1:20 when necessary for drainage. Outdoor Constructed Features The proposed rule contained separate scoping and technical requirements for picnic tables, fire rings, grills, fireplaces, wood stoves, trash and recycling receptacles, water hydrants, utility and sewage hookups, outdoor rinsing showers, benches, and viewing scopes. The final rule collectively defines these elements as outdoor constructed features. The proposed rule would have required 50 percent of picnic tables, fire rings, grills, and benches to comply with the applicable technical requirements, and would have required at least 40 percent of these elements that complied with the applicable technical requirements to be on an outdoor recreation access route. In the final rule, the scoping requirements for camping facilities, picnic facilities, viewing areas, trailheads, and trails include scoping requirements for outdoor constructed features; and the technical requirements for outdoor constructed features are contained in 1011. The final rule requires every outdoor constructed PO 00000 Frm 00006 Fmt 4701 Sfmt 4700 feature that complies with the applicable technical requirements in 1011 to be on an outdoor recreation access route. The proposed rule based the size of the clear ground space at outdoor constructed features on the dimensions for clear floor or ground surfaces in 305.2 of the Architectural Barriers Act Accessibility Guidelines. The final rule bases the size of the clear ground space at outdoor constructed features on the dimensions for maneuvering clearance at clear floor or ground spaces that are confined on all or part of three sides in 305.7 of the Architectural Barriers Act Accessibility Guidelines. Outdoor constructed features can be confined on all or part of three sides by surfaces that are not firm and stable or that have changes in level. The dimensions for maneuvering clearance at clear floor or ground spaces that are confined on all or part of three sides in 305.7 of the Architectural Barriers Act Accessibility Guidelines provide additional space for maneuvering into and out of the space: 36 inches minimum by 48 inches minimum for a forward approach, and 30 inches minimum by 60 inches minimum for a parallel approach. At water hydrants, a clear ground space for a forward approach is required on each side of the water hydrant to enable individuals with disabilities to operate the water hydrant from their right side or left side. At rinsing showers, the size of the clear ground space is based on the dimensions for turning space in 304.3.1 of the Architectural Barriers Act Accessibility Guidelines to enable individuals with disabilities to turn in the space. The proposed rule would have required outdoor rinsing showers to provide grab bars. Outdoor rinsing showers typically are provided at beaches for rinsing off sand and lotions that people apply to their bodies when they are outdoors. They are not designed for bathing and do not offer privacy. Individuals who use wheeled mobility devices are not expected to transfer from the devices when using outdoor rinsing showers and do need grab bars for this purpose. Therefore, the final rule does not require grab bars at rinsing showers. The proposed rule also would have required outdoor rinsing showers to provide a fixed shower head at a lower height. The final rule requires outdoor rinsing showers to provide a hand-held shower spray unit that has at least one fixed position located 15 inches minimum and 48 inches maximum above the ground. Where vandalism is a consideration, a fixed shower head located 48 inches above the ground is E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations permitted in place of a hand-held shower spray unit. The proposed rule would have required benches to provide a backrest and armrests. The final rule does not require a backrest and armrests due to the varied designs and configurations of benches. Elements Exempted in Final Rule The proposed rule included proposed scoping and technical requirements for utility sinks and pit toilets. The final rule exempts these elements from the scoping requirements in F212.3 and F213.1 of the Architectural Barriers Act Accessibility Guidelines. Elements Not Addressed in Final Rule The proposed rule included proposed scoping and technical requirements for recreational vehicle parking spaces in general parking areas at camping facilities. The final rule includes scoping and technical requirements for recreational vehicle parking spaces in camping units with mobility features and recreational vehicle pull-up spaces at dump stations. The final rule does not address recreational vehicle parking spaces in other areas. The proposed rule included proposed scoping and technical requirements for mobility device storage facilities and warming huts. The final rule does not address these elements because they are not typically provided at the facilities addressed in the final rule. 5. Discussion of Scoping and Technical Requirements The scoping and technical requirements in the final rule are discussed below. Appendix C to 36 CFR Part 1191— Architectural Barriers Act: Scoping ABA Chapter 1: Application and Administration emcdonald on DSK67QTVN1PROD with RULES2 F106.5 Defined Terms The final rule adds definitions to this section for the following terms: boards, camp shelter, camping facility, camping unit, outdoor constructed features, picnic facility, picnic unit, trail, trailhead, and viewing areas. The definition of boards is discussed above under the Executive Summary. The definition of outdoor constructed features is discussed above under Changes Made to the Proposed Rule. The definitions of the other terms are discussed below under the sections where the terms are used. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 ABA Chapter 2: Scoping Requirements F201.4 Requirements Apply to Facilities Constructed or Altered by or on Behalf of Federal Agencies This section provides that the scoping requirements in F216.13 and F244 though F248 and the technical requirements in 1011 through 1019 apply to camping facilities, picnic facilities, viewing areas, trails, and beach access routes constructed or altered by federal agencies or by nonfederal entities on federal land on behalf of federal agencies pursuant to a concession contract, partnership agreement, or similar arrangement. F201.4.1 Documentation and Notification When Exceptions Used for Trails or Beach Access Routes This section requires federal agencies to document the basis for not fully complying with a specific provision in the technical requirements for trails on a portion of a trail based on Exception 1 in 1017, or with a specific provision in the technical requirements for beach access routes based on Exception 1 in 1018. Federal agencies are required to maintain the documentation with the records for the trail or beach project. The section also requires federal agencies to notify us if an entire trail is exempted from complying with the technical requirements for trails based on Exception 2 in 1017, and if a beach access route is not provided based on Exception 2 in 1018. Notification forms are available on our Web site at: https:// www.access-board.gov/outdoor. F202.3 Alterations The final rule adds Exception 4 to this section, which applies to altered elements and spaces. Exception 4 does not require an outdoor recreation access route to altered elements and spaces in camping facilities, picnic facilities, viewing areas, or trailheads where the circulation path to the altered element or space is not altered. Exception 4 is consistent with Exception 1 to this section, which does not require an accessible route to altered elements and spaces in other types of facilities where the circulation path to the altered element or space is not altered, unless the alterations affect primary function areas. F202.4 Alterations Affecting Primary Function Areas The final rule adds Exception 2 to this section, which applies to altered areas containing a primary function. Exception 2 exempts camping facilities, picnic facilities, viewing areas, trailheads, trails, and beach access PO 00000 Frm 00007 Fmt 4701 Sfmt 4700 59481 routes from providing an accessible path of travel to altered areas containing a primary function. The regulations and policies issued by the federal agencies referenced in the section define an accessible path of travel as an accessible route. Exception 4 is added because the final rule does not require accessible routes at camping facilities, picnic facilities, viewing areas, and trailheads where outdoor recreation access routes are provided. The final rule also does not require accessible routes where camping facilities, picnic facilities, and viewing areas are provided on trails and where beach access routes are provided. F206.1 General The final rule adds three exceptions to this section, which contains the scoping requirements for accessible routes. Exception 1 does not require accessible routes at camping facilities, picnic facilities, viewing areas, and trailheads where outdoor recreation access routes are provided. Exception 2 does not require accessible routes where camping facilities, picnic facilities, viewing areas, and outdoor constructed features are provided on trails. Exception 3 does not require accessible routes where beach access routes are provided. F212.3 Sinks The final rule adds Exception 2 to this section, which contains the scoping requirements for sinks. Exception 2 exempts sinks in camping facilities and picnic facilities where a cooktop or conventional range is not provided. Exception 2 applies to utility sinks used to clean large pots and equipment. Exception 2 is consistent with Exception 1 to this section, which exempts service sinks because they cannot comply with technical requirements for sinks due to their configuration. Utility sinks used to clean large pots and equipment are configured similar to service sinks. Lavatories (i.e., sinks in toilet and bathing facilities) are not affected by Exception 2. F213.1 General The final rule adds an exception to this section, which contains the scoping requirements for toilet facilities. The exception exempts pit toilets provided on trails and in camping facilities. A pit toilet is a primitive outhouse consisting of a toilet riser over a hole dug into the ground or receptacle to receive and naturally decompose human waste. Some pit toilets do not have walls and would not be able to comply with the technical requirements for toilet facilities such as providing grab bars at E:\FR\FM\26SER2.SGM 26SER2 59482 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations toilet fixtures. However, the technical requirements for toilet facilities can be used as guidance for designing pit toilets. F216.13 Trailhead Signs Where new trail information signs are provided at trailheads on newly constructed or altered trails designed for use by hikers or pedestrians, this section requires the signs to comply with the technical requirements in 1017.11, regardless of whether the trails comply with the technical requirements in 1017. The technical requirements in 1017.11 require the signs to include information on the length of the trail or trail segment; surface type; typical and minimum tread width; typical and minimum running slope; and typical and minimum cross slope. This information enables individuals with disabilities to decide whether to hike the trail based on the characteristics of the trail. Entities should also provide information about the accessibility of trails on Web sites. If trail information signs designate the name of the trail, only the name of the trail is required to comply with the technical requirements in 703.5. See F216.2. Tactile characters are not required on exterior signs. Trail information signs are not required to display the International Symbol of Accessibility. emcdonald on DSK67QTVN1PROD with RULES2 F244 Camping Facilities F244.1 General This section contains the scoping requirements for camping facilities, other than camping facilities on trails. The scoping requirements for camping facilities on trails are contained in F247.4.1. The terms camping facility, camping unit, and camp shelter are defined in F106.5. A camping facility is a site, or a portion of a site, developed for outdoor recreational purposes that contains camping units. A camping unit is an outdoor space in a camping facility used for camping that contains outdoor constructed features, parking spaces for recreational vehicles or other vehicles, tent pads or tent platforms, or camp shelters. A camp shelter is a partially enclosed structure that provides campers and hikers cover from weather and that does not contain plumbing fixtures or kitchen appliances. Camp shelters are not transient lodging facilities or residential dwelling units. F244.2 Camping Units With Mobility Features This section requires camping facilities to provide a minimum number of camping units with mobility features based on the total number of camping VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 units in accordance with Table 244.2. Where different types of camping units are provided (e.g., camping units for recreational vehicles only; camping units for tent camping only; and camping units with camp shelters), Table 244.2 applies to each type of camping unit provided. Camping units with mobility features are not required to be identified by signs. Entities should provide information on the location of camping units with mobility features on Web sites, in brochures, and at bulletin boards or information kiosks at the camping facility. Where entities operate reservation systems for camping units or assign camping units upon arrival, entities should establish policies to ensure that camping units with mobility features are available for individuals with disabilities until all the camping units are occupied. F244.2.1 Alterations and Additions This section requires camping units that are altered or added to provide mobility features until the number of camping units with mobility features in the camping facility meets the minimum number required in Table 244.2. Where an entity is implementing a transition plan for program accessibility developed pursuant to regulations issued under section 504 of the Rehabilitation Act that designates specific camping units to provide mobility features, an exception permits the entity to not provide accessible elements when altering individual elements within camping units that are not designated to provide mobility features. When all the elements within a camping unit are altered, the altered camping unit is required to provide mobility features until the minimum number of camping units with mobility features required in Table 244.2 is met. F244.2.2 Dispersion This section requires camping units with mobility features to provide choices of camping units comparable to, and integrated with, those available to others. F244.2.3 Elements Within Camping Units With Mobility Features This section contains the scoping requirements for elements within camping units required to provide mobility features, including outdoor constructed features (F244.2.3.1), parking spaces for recreational vehicles (F244.2.3.2.1), parking spaces for vehicles other than recreational vehicles (F244.2.3.2.2), tent pads and tent platforms (F244.2.3.3), and camp shelters (F244.3.4). Where these PO 00000 Frm 00008 Fmt 4701 Sfmt 4700 elements are provided within a camping unit, at least one of each type of element is required to comply with the applicable technical requirements for the element. Where more than one of the same element is provided within a camping unit (e.g., picnic tables, tent pads), at least two of the same type element are required to comply with the applicable technical requirements for the element. F244.3 Outdoor Constructed Features in Common Use and Public Use Areas This section contains the scoping requirements for outdoor constructed features provided in common use and public use areas that serve camping units with mobility features. At least 20 percent, but not less than one, of each type of outdoor constructed feature provided at each location is required to comply with the applicable technical requirements in 1011. F244.4 Pull-up Spaces for Recreational Vehicles at Dump Stations This section requires pull-up spaces provided for recreational vehicles at dump stations to comply with the applicable technical requirements in 1012. F244.5 Routes Outdoor Recreation Access This section contains the scoping requirements for outdoor recreation access routes at camping facilities, which are discussed below. F244.5.1 Routes Within Camping Units With Mobility Features This section requires at least one outdoor recreation access route to connect accessible elements, spaces, and facilities provided within camping units with mobility features. F244.5.2 Routes to and Within Common Use and Public Use Areas This section requires at least one outdoor recreation access route to connect each camping unit with mobility features with common use and public use areas serving the unit; and at least one outdoor recreation access route to connect accessible elements, spaces, and facilities provided within common use and public use areas serving camping units with mobility features. An outdoor recreation access route is not required to connect camping units with mobility features and recreational vehicle dump stations where a pull-up space complying with the applicable technical requirements in 1012 is provided at the dump station for recreational vehicles. E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations F244.5.3 Routes to Adjacent Recreation Facilities Where a circulation path connects camping facilities and adjacent recreation facilities, this section requires at least one outdoor recreation access route to connect camping units with mobility features to an accessible route serving the adjacent recreation facilities. The section does not modify the scoping requirements for accessible routes in F206 of the Architectural Barriers Act Accessibility Guidelines that apply to recreation facilities. F244.5.4 Location This section requires outdoor recreation access routes to coincide with or be located in the same general area as general circulation paths. Where a vehicular way serves as the general circulation path for pedestrians at a camping facility, the outdoor recreation access route can be provided within the vehicular way. F245 F245.1 Picnic Facilities General This section contains the scoping requirements for picnic facilities, other than picnic facilities on trails. The scoping requirements for picnic facilities on trails are contained in F247.4.2. The terms picnic facility and picnic unit are defined in F106.5. A picnic facility is a site, or a portion of a site, developed for outdoor recreational purposes that contains picnic units. A picnic unit is an outdoor space in a picnic facility used for picnicking that contains outdoor constructed features. F245.2 Picnic Units With Mobility Features This section requires picnic facilities to provide a minimum number of picnic units with mobility features as discussed below. Picnic units with mobility features are not required to be identified by signs. Entities should provide information on the location of picnic units with mobility features on Web sites, in brochures, and at bulletin boards or information kiosks at the picnic facility. emcdonald on DSK67QTVN1PROD with RULES2 F245.2.1 Picnic Facilities With Two or Fewer Picnic Units Where picnic facilities contain two or fewer picnic units, this section requires each picnic unit to provide mobility features. F245.2.2 Picnic Facilities With More Than Two Picnic Units Where picnic facilities contain more than two picnic units, this section VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 requires at least 20 percent, but not less than two, of the picnic units to provide mobility features. F245.2.3 Alterations and Additions This section requires picnic units that are altered or added to provide mobility features until the number of picnic units with mobility features in the picnic facility meets the minimum number required in F245.2.1 or F245.2.2. Where an entity is implementing a transition plan for program accessibility developed pursuant to regulations issued under section 504 of the Rehabilitation Act that designates specific picnic units to provide mobility features, an exception permits the entity to not provide accessible elements when altering individual elements within picnic units that are not designated to provide mobility features. When all the elements within a picnic unit are altered, the altered picnic unit is required to provide mobility features until the minimum number of picnic units with mobility features required in F245.2.1 or F245.2.2 is met. F245.2.4 Dispersion This section requires picnic units with mobility features to provide choices of picnic units comparable to, and integrated with, those available to others. F245.2.5 Elements Within Picnic Units With Mobility Features This section contains the scoping requirements for elements within picnic units required to provide mobility features, including outdoor constructed features (F244.2.5.1) and parking spaces (F244.2.5.2). Where these elements are provided within a picnic unit, at least one of each type of element is required to comply with the applicable technical requirements for the element. Where more than one of the same element is provided within a picnic unit (e.g., picnic tables, grills), at least two of the same type of element are required to comply with the applicable technical requirements for the element. F245.3 Outdoor Constructed Features in Common Use and Public Use Areas This section contains the scoping requirements for outdoor constructed features provided in common use and public use areas that serve picnic units with mobility features. At least 20 percent, but not less than one, of each type of outdoor constructed feature provided at each location is required to comply with the applicable technical requirements in 1011. PO 00000 Frm 00009 Fmt 4701 Sfmt 4700 59483 F245.4 Outdoor Recreation Access Routes This section contains the scoping requirements for outdoor recreation access routes within picnic facilities, which are discussed below. F245.4.1 Routes Within Picnic Units With Mobility Features This section requires at least one outdoor recreation access route to connect accessible elements, spaces, and facilities provided within picnic units with mobility features. F245.4.2 Routes to and Within Common Use and Public Use Areas This section requires at least one outdoor recreation access route to connect each picnic unit with mobility features with common use and public use areas serving the unit; and at least one outdoor recreation access route to connect accessible elements, spaces, and facilities provided within common use and public use areas serving picnic units with mobility features. F245.4.3 Routes to Adjacent Recreation Facilities Where a circulation path connects picnic facilities and adjacent recreation facilities, this section requires at least one outdoor recreation access route to connect picnic units with mobility features to an accessible route serving the adjacent recreation facilities. The section does not modify the scoping requirements for accessible routes in F206 of the Architectural Barriers Act Accessibility Guidelines that apply to recreation facilities. F245.4.4 Location This section requires outdoor recreation access routes to coincide with or be located in the same general area as general circulation paths. Where a vehicular way serves as the general circulation path for pedestrians at a picnic facility, the outdoor recreation access route can be provided within the vehicular way. F246 Viewing Areas F246.1 General This section contains the scoping requirements for viewing areas, other than viewing areas on trails. The scoping requirements for viewing areas on trails are contained in F247.4.3. The term viewing area is defined in F106.5 as an outdoor space developed for viewing a landscape, wildlife, or other points of interest. F246.2 Distinct Viewing Locations This section requires each distinct viewing location within a viewing area E:\FR\FM\26SER2.SGM 26SER2 59484 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations to comply with the technical requirements for viewing areas in 1015. Viewing areas can provide more than one distinct viewing location. For example, a viewing area can provide a distinct viewing location for observing a mountain range, and another distinct viewing location for observing a river. Distinct viewing locations within a viewing area can be designated by signs or other markers. F246.3 Outdoor Constructed Features This section requires at least 20 percent, but not less than one, of each type of outdoor constructed feature provided within viewing areas to comply with the applicable technical requirements in 1011. F246.4 Outdoor Recreation Access Routes This section requires at least one outdoor recreation access route to connect accessible parking spaces or other site arrival points serving the viewing area with accessible elements, spaces, and facilities provided within the viewing area. emcdonald on DSK67QTVN1PROD with RULES2 F247 Trails F247.1 General This section contains the scoping requirements for trails. The terms trail and trailhead are defined in F106.5. A trail is a pedestrian route developed primarily for outdoor recreational purposes. A pedestrian route developed primarily to connect elements, spaces, and facilities within a site is not a trail. A trailhead is an outdoor space that is designated by an entity responsible for administering or maintaining a trail to serve as an access point to the trail. The junction of two or more trails or the undeveloped junction of a trail and a road is not a trailhead. Where a trail is designed for use by hikers or pedestrians and directly connects to a trailhead or another trail that substantially meets the technical requirements for trails in 1017, the section requires the trail to comply with the technical requirements for trails in 1017. The Federal Trail Data Standards classify trails by their designed use and managed use.8 A trail has only one designed use that determines the design, construction, and maintenance parameters for the trail. A trail can have more than one managed use based on a management decision to allow other uses on the trails. Trails that have a designed use for hikers or pedestrians are required to comply with the 8 The Federal Trail Data Standards are available at: https://www.fgdc.gov/standards/projects/FGDCstandards-projects/trail-data-standard/. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 technical requirements for trails in 1017. Trails that have a designed use for other than hikers or pedestrians are not required to comply with the technical requirements for trails in 1017. A trail system may include a series of connecting trails. Only trails that directly connect to a trailhead or another trail that substantially meets the technical requirement for trails in 1017 are required to comply with the technical requirements for trails in 1017. facilities and accessible elements provided within the facilities are not required to comply with the technical requirements for trails in 1017. F247.2 Existing Trails Where the original design, function, or purpose of an existing trail is changed and the altered portion of the trail directly connects to a trailhead or another trail that substantially meets the technical requirements for trails in 1017, this section requires the altered portion of the trail to comply with the technical requirements for trails in 1017. Routine or periodic maintenance activities that are performed to return an existing trail to the condition to which the trail was originally designed are not required to comply with the technical requirements for trails in 1017. F248 F247.3 Trailheads This section requires at least 20 percent, but not less than one, of each type of outdoor constructed feature provided within trailheads to comply with the applicable technical requirements in 1011. The section also requires at least one outdoor recreation access route to connect accessible parking spaces or other site arrival points serving the trailhead; the starting point of the trail; and accessible elements, spaces, and facilities provided within the trailhead. F247.4 Trail Facilities This section requires camping facilities, picnic facilities, and viewing areas provided on trails to comply with the applicable scoping requirements for the facilities in F244 through F246, except for the scoping requirements for outdoor recreation access routes. The facilities are required to comply with the applicable scoping requirements regardless of whether the trail complies with the technical requirements for trails in 1017. The section requires routes that connect trails complying with the technical requirements for trails in 1017 to camping facilities, picnic facilities, viewing areas, pit toilets, and accessible elements within the facilities to comply with the technical requirements for trails in 1017. Routes that connect trails that do not comply with the technical requirements for trails in 1017 to these PO 00000 Frm 00010 Fmt 4701 Sfmt 4700 F247.5 Outdoor Constructed Features This section requires at least 20 percent, but not less than one, of each type of outdoor constructed feature provided at each location on trails, other than within facilities provided on trails, to comply with the applicable technical requirements in 1011. Beach Access Routes F248.1 General This section contains the scoping requirements for beach access routes. Where the entity that administers or manages a beach constructs or alters circulation paths, parking facilities, toilet facilities, or bathing facilities to serve the beach or undertakes a beach nourishment project, the section requires the entity to provide beach access routes. The entity is not required to expend more than 20 percent of the costs to construct or alter the facilities serving the beach or the beach nourishment project to provide beach access routes. Beach access routes can be permanent or removable. Removable beach access routes can be moved to a protected storage area during storms and other periods when the routes are subject to damage or loss. Beach access routes are not required where pedestrian access to the beach is not permitted. F248.2 Minimum Number This section requires at least one beach access route to be provided for each 1⁄2 mile of beach shoreline administered or managed by the entity. The number of beach access routes is not required to exceed the number of pedestrian access points provided by the entity to the beach. Pedestrian access points to a beach include parking facilities that serve beaches, dune crossings, and stairways or ramps leading from boardwalks to the beach. F248.3 Location This section requires beach access routes to coincide with or be located in the same general area as pedestrian access points to the beach. Appendix D to 36 CFR Part 1191— Technical Chapter 10: Recreation Facilities The final rule adds technical requirements to Chapter 10 for outdoor constructed features (1011); parking spaces within camping units and picnic units and pull-up spaces at dump stations (1012); tent pads and tent E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations platforms (1013); camp shelters (1014); viewing areas (1015); outdoor recreation access routes (1016); trails (1017); and beach access routes (1018). The final rule also adds the conditions for using the exceptions to the specific provisions in these technical requirements at 1019. 1011 Outdoor Constructed Features 1011.1 General This section contains the technical requirements for outdoor constructed features provided within camping facilities, picnic facilities, viewing areas, and trailheads or on trails. All outdoor constructed features are required to comply with the provisions for clear ground space (1011.2) and operable parts (1011.3). The section includes specific provisions for picnic tables (1011.4); fire rings, grills, fireplaces, and woodstoves (1011.5); water spouts at water hydrants and water utility hook-ups (1011.6); outdoor rinsing showers (1011.7); and viewing scopes (1011.8). emcdonald on DSK67QTVN1PROD with RULES2 1011.2 Clear Ground Space This section requires a clear ground space to be provided at outdoor constructed features and includes specific provisions for the size and location (1011.2.1), surface (1011.2.2), slope (1011.2.3), and openings (1011.2.4). Two exceptions are provided. Where individual outdoor constructed features are altered and the ground surface is not altered, Exception 1 does not require the clear ground space to comply with the specific provisions for surface and slope. In alterations, when an entity determines that a condition in 1019 does not permit full compliance with a specific provision, Exception 2 permits the clear ground space to comply with the provision to the extent practicable. 1011.2.1 Size and Location This section specifies the size and location of the clear ground space at outdoor constructed features. The size of the clear ground space is based on the dimensions for maneuvering clearance at clear floor or ground spaces that are confined on all or part of three sides in 305.7 of the Architectural Barriers Act Accessibility Guidelines. Outdoor constructed features can be confined on all or part of three sides by surfaces that are not firm and stable or that have changes in level. The dimensions for maneuvering clearance at clear floor or ground spaces that are confined on all or part of three sides in 305.7 of the Architectural Barriers Act Accessibility Guidelines provide additional space for maneuvering into and out of the space: 36 inches minimum by 48 inches VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 minimum for a forward approach, and 30 inches minimum by 60 inches minimum for a parallel approach. At water hydrants, a clear ground space for a forward approach is required on each side of the water hydrant to enable individuals with disabilities to operate the water hydrant from their right side or left side. At rinsing showers, the size of the clear ground space is based on the dimensions for turning space in 304.3.1 of the Architectural Barriers Act Accessibility Guidelines to enable individuals with disabilities to turn in the space. At picnic tables, fire rings, grills, fireplaces, and woodstoves, a clear ground space is required on all usable sides of the element. The usable sides of these elements are the sides that can be used for eating or serving food, building a fire, or cooking. All sides of picnic tables are generally usable, unless the picnic table is placed against a rock or tree that renders the side against the rock or tree not usable. All sides of fire rings and grills are generally usable, unless there is a wall or other structure on a side that renders the side not usable. The front sides of fireplaces and woodstoves are generally the usable side. 1011.2.2 Surface This section requires the surface of the clear ground space to be firm and stable. 1011.2.3 Slope This section requires the slope of the clear ground space to not be steeper than 1:48 in any direction. Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. 1011.2.4 Openings This section requires openings in the clear ground space such as drainage grates to not allow passage of a sphere more than 1⁄2 inch in diameter. Where possible, drainage grates should be located outside of the clear ground space. Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel. 1011.3 Operable Parts This section requires operable parts of outdoor constructed features to comply with the technical requirements for the height of operable parts in 309.3 of the Architectural Barriers Act Accessibility Guidelines, which require operable parts to be placed within the reach ranges specified in 308 of the PO 00000 Frm 00011 Fmt 4701 Sfmt 4700 59485 Architectural Barriers Act Accessibility Guidelines; and the technical requirements for operation in 309.4 of the Architectural Barriers Act Accessibility Guidelines, which require operable parts to be operable with one hand without tight grasping, pinching, or twisting of the wrist and with not more than 5 pounds force. Four exceptions are provided. Exception 1 requires fire rings, grills, fireplaces, wood stoves, water hydrants, and water utility hook-ups to comply with the technical requirements for operation in 309.4 of the Architectural Barriers Act Accessibility Guidelines to the extent practicable. Exception 2 requires trash and recycling receptacles with hinged lids and controls to keep out large animals to comply with the technical requirements for operation in 309.4 of the Architectural Barriers Act Accessibility Guidelines to the extent practicable. Exception 3 exempts dumpster type trash and recycling receptacles from complying with the technical requirements for the height of operable parts in 309.3 of the Architectural Barriers Act Accessibility Guidelines and the technical requirements for operation in 309.4 of the Architectural Barriers Act Accessibility Guidelines. Exception 4 exempts sewage hatches from complying with the technical requirements for the height of operable parts in 309.3 of the Architectural Barriers Act Accessibility Guidelines and the technical requirements for operation in 309.4 of the Architectural Barriers Act Accessibility Guidelines. New products may be developed with operable parts that comply with the technical requirements for operation in 309.4 of the Architectural Barriers Act Accessibility Guidelines. As products that comply with the technical requirements for operation in 309.4 of the Architectural Barriers Act Accessibility Guidelines become available, entities should provide these products to enable individuals with disabilities to operate them. 1011.4 Picnic Tables This section requires picnic tables to comply with the technical requirements for dining surfaces in 902.3 of the Architectural Barriers Act Accessibility Guidelines, which requires the tops of dining surfaces to be 28 inches minimum and 34 inches maximum above the ground. The section also requires at least one wheelchair space to be provided for each 24 linear feet of usable picnic table surface perimeter. Wheelchair spaces are required to be 30 inches minimum by 48 inches minimum; be positioned for a forward E:\FR\FM\26SER2.SGM 26SER2 59486 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations approach to the table; and provide knee and toe clearance complying with 306 of the Architectural Barriers Act Accessibility Guidelines under the table. 1011.5 Fire Rings, Grills, Fireplaces, and Wood Stoves This section requires fire building surfaces to be 9 inches minimum above the ground, and cooking surfaces to be 15 inches minimum and 34 inches maximum above the ground. Where fire rings, grills, or fireplaces are constructed with raised edges or walls, the depth of the raised edge or wall is required to be 10 inches maximum. Fire rings with double walls or insulation on the sides are recommended to prevent burns. 1011.6 Water Spouts This section requires water spouts at water hydrants and water utility hookups to be 28 inches minimum and 36 inches maximum above the ground. 1011.7 Outdoor Rinsing Showers This section requires outdoor rinsing showers to provide at least one handheld shower spray unit with a hose 59 inches long minimum. The hand-held shower spray unit is required to have at least one fixed position located 15 inches minimum and 48 inches maximum above the ground. Where vandalism is a consideration, a fixed shower head located 48 inches above the ground is permitted in place of a hand-held shower spray unit. 1011.8 Viewing Scopes This section requires eyepieces on viewing scopes to be 43 inches minimum and 51 inches maximum above the ground. accommodate recreational vehicles equipped with a lift. Recreational vehicles are typically 8 feet wide. Recreational vehicles equipped with a lift need an additional 8 feet of space on the passenger’s side to deploy the lift and for individuals who use wheeled mobility devices to maneuver onto and off of the lift. Utility hook-ups for recreational vehicles are typically located on the driver’s side of the vehicle. An additional 4 feet of space is needed on the driver’s side for individuals who use wheeled mobility devices to access the utility hook-ups. Where two adjacent parking spaces are provided for recreational vehicles, one of the parking spaces is permitted to be 16 feet wide minimum. 1013.2 1012.3 1013.3 Other Vehicles 1012.4 This section requires tent platforms to be 19 inches high maximum measured from the clear ground space to the tent platform surface. Surface This section requires the surface of parking spaces and pull-up spaces to be firm and stable. 1012.5 Slope emcdonald on DSK67QTVN1PROD with RULES2 This section contains the technical requirements for tent pads and tent platforms provided within camping units with mobility features. Tent pads and tent platforms are defined spaces with prepared surfaces for setting up and securing tents. The technical requirements address the clear ground space around tent pads and tent platforms (1013.2); the slope of tent pads, tent platforms, and clear ground spaces (1013.2); and the height of tent platforms (1013.4). When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1013, the tent pad or tent platform is permitted to comply with the provision to the extent practicable. Jkt 229001 1013.1 PO 00000 Tent Pads & Tent Platforms General Frm 00012 Fmt 4701 1013.4 1014 Height Camp Shelters 1014.1 This section requires the slope of the surface of parking spaces and pull-up spaces to not be steeper than 1:48 in any direction. Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. 1012.1 General This section contains the technical requirements for parking spaces provided within camping units and picnic units with mobility features and pull-up spaces for recreational vehicles at dump stations. The technical requirements address the width of parking spaces and pull-up spaces for recreational vehicles (1012.2); the width of parking spaces for vehicles, other than recreational vehicles (1012.3); and the surface (1012.4) and slope (1012.5) of parking spaces and pull-up spaces. 18:25 Sep 25, 2013 Slope This section requires parking spaces for vehicles, other than recreational vehicles, to be 16 feet wide minimum to accommodate vans equipped with a lift or ramp. Where two adjacent parking spaces are provided for vehicles, other than recreational vehicles, one of the parking spaces is permitted to be 8 feet wide minimum. 1013 VerDate Mar<15>2010 This section requires a clear ground space 4 feet wide minimum to be provided on all usable sides of tent pads and tent platforms to enable individuals who use wheeled mobility devices to set up and take down the tent. The usable sides of tent pads and tent platforms are the sides that can be used when setting up and taking down a tent. All sides of tent pads and tent platforms are generally usable, unless a tent pad or tent platform is located next to a natural feature such as a rock or tree that renders a side not usable. This section also requires the surface of the clear ground space to be firm and stable and to allow the use of tent stakes or other tent securement devices. This section requires the slope of the surface of tent pads, tent platforms, and clear ground spaces to not be steeper than 1:48 in any direction. Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. 1012 Parking Spaces Within Camping Units and Picnic Units and Pull-Up Spaces at Dump Stations 1012.2 Recreational Vehicles This section requires parking spaces and pull-up spaces for recreational vehicles to be 20 feet wide minimum to Clear Ground Space Sfmt 4700 General This section contains the technical requirements for camp shelters with mobility features. The technical requirements address the entrance to camp shelters (1014.2), including transfer access (1014.2.1) and roll-in access (1014.2.2); and the floor within camp shelters (1014.3). Two exceptions are provided. When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1014, Exception 1 permits the camp shelter to comply with the provision to the extent practicable. Exception 2 does not require camp shelters to comply with the technical requirements for protruding objects in 307 of the Architectural Barriers Act Accessibility Guidelines. 1014.2 Entrance This section requires camp shelters to provide either transfer access or roll-in access at the entrance to the camp shelter. 1014.2.1 Transfer Access Where transfer access is provided, this section requires a clear ground E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations space 36 inches minimum by 48 inches minimum positioned for a parallel approach to be provided at the entrance to the camp shelter, and one full unobstructed side of the clear ground space to adjoin or overlap an outdoor recreation access route or trail, as applicable, or another clear ground space. The surface of the clear ground space is required to be firm and stable, and to slope not steeper than 1:48 in any direction. Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. The camp shelter floor at the entrance is required to be 19 inches high maximum measured from the clear ground space. These requirements enable individuals who use wheeled mobility devices to transfer from their mobility device to the shelter floor 1014.2.2 Roll-in Access Where roll-in access is provided, this section requires a level or sloped entry route complying with the technical requirements for outdoor recreation access routes in 1016 or trails in 1017, as applicable, at the entrance to the camp shelter. The section also requires a turning space complying with 304.3 of the Architectural Barriers Act Accessibility Guidelines to be provided within the camp shelter. These requirements enable individuals who use wheeled mobility devices to enter the shelter in their mobility device. 1014.3 Floor This section requires the floor surface within camp shelters to be firm and stable and to slope not steeper than 1:48 in any direction. Where the floor surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. emcdonald on DSK67QTVN1PROD with RULES2 1015 Viewing Areas 1015.1 General This section contains the technical requirements for viewing areas. The technical requirements address the clear ground space (1015.2) and viewing space (1015.3) at distinct viewing locations; the turning space within viewing areas (1015.4); and the surface (1015.5) and slope (1015.6) of the clear ground space and turning space. In alterations, when an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1015, the viewing area is permitted to comply with the provision to the extent practicable. 1015.2 Clear Ground Space This section requires a clear ground space 36 inches minimum by 48 inches VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 minimum positioned for either a forward or parallel approach to be provided at each distinct viewing location, and one full unobstructed side of the clear ground space to adjoin or overlap an outdoor recreation access route or trail, as applicable, or another clear ground space. 1015.3 Viewing Space This section requires each distinct viewing location to provide a viewing space adjacent to the clear ground space required by 1015.2 through which the point of interest is viewable. The viewing space is required to be 32 inches maximum and 51 inches minimum high above the ground and extend the full width of the clear ground space. Guards or similar safety barriers are permitted to obstruct the viewing space to the extent the obstruction is necessary for the guard or safety barrier to serve its intended purpose. 1015.4 Turning Space This section requires a turning space complying with 304.3 of the Architectural Barriers Act Accessibility Guidelines to be provided within the viewing area. 1015.5 Surface This section requires the surface of the clear ground space and turning space to be firm and stable. 1015.6 Slope This section requires the slope of the surface of the clear ground space and turning space to not be steeper than 1:48 in any direction. Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. 1016 Outdoor Recreation Access Routes 1016.1 General This section contains the technical requirements for outdoor recreation access routes. The technical requirements address the surface of outdoor recreation access routes, passing spaces, and resting intervals (1016.2); the clear width of outdoor recreation access routes (1016.3); passing spaces (1016.4); obstacles (1016.5); openings (1016.6); slopes, including running slope (1016.7.1) and cross slope (1016.7.2); resting intervals (1016.8); and protruding objects (1016.9). Three exceptions are provided. Exception 1 applies to alterations of existing camping facilities, picnic facilities, and trailheads. Exception 2 applies to new construction and alterations of viewing areas. When an PO 00000 Frm 00013 Fmt 4701 Sfmt 4700 59487 entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1016 on a portion of an outdoor recreation access route, Exceptions 1 and 2 permit the portion of the outdoor recreation access route to comply with the provision to the extent practicable. Exception 3 exempts outdoor recreation access routes that are provided within vehicular ways from complying with the technical requirements for passing spaces (1016.4); running slope (1016.7.1) and cross slope (1016.7.2); and resting intervals (1016.8). 1016.2 Surface This section requires the surface of outdoor recreation access routes, passing spaces, and resting intervals to be firm and stable. 1016.3 Clear Width This section requires the clear width of outdoor recreation access routes to be 36 inches minimum. 1016.4 Passing Spaces This section requires passing spaces to be provided at intervals of 200 feet maximum where the clear width of outdoor recreation access routes is less than 60 inches. Entities should consider providing either 60 inches minimum clear width on outdoor recreation access routes or passing spaces at shorter intervals where the route is heavily used or adjoins elements, spaces, or facilities that are heavily used; or where the route is a boardwalk or otherwise not at the same level as the adjoining ground surface. Passing spaces are required to be: • A space 60 inches minimum by 60 inches minimum; or • The intersection of two outdoor recreation access routes providing a Tshaped space complying with 304.3.2 of the Architectural Barriers Act Accessibility Guidelines where the base and the arms of the T-shaped space extend 48 inches minimum beyond the intersection. Where the intersection of two outdoor recreation access routes serves as a passing space, the vertical alignment of the routes at the intersection that form the T-shaped space is required to be nominally planar (i.e., as flat as possible) so that all the wheels of a mobility device touch the ground when turning into and out of the passing space. Passing spaces and resting intervals are permitted to overlap. Where passing spaces and resting intervals overlap, the technical requirements for resting intervals in 1016.8.3 require the slope of the surface to not be steeper than 1:48 E:\FR\FM\26SER2.SGM 26SER2 59488 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations in any direction. Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. Otherwise, passing space surfaces have the same slopes as the adjoining outdoor recreation access route. 1016.5 Obstacles This section contains technical requirements for obstacles on outdoor recreation access routes, passing spaces, and resting intervals. The vertical alignment of joints in concrete, asphalt, or board surfaces on outdoor recreation access routes can be obstacles. Natural features such as tree roots and rocks on outdoor recreation access routes also can be obstacles. Where an outdoor recreation access route is provided within a vehicular way, traffic calming devices can be obstacles. This section requires obstacles to not exceed 1⁄2 inch in height measured vertically to the highest point. Where the surface is other than concrete, asphalt, or boards, obstacles are permitted to not exceed 1 inch in height measured vertically to the highest point. The frequency of obstacles and obstacles that cross the full width of outdoor recreation access routes can make travel difficult for individuals who use wheeled mobility devices. Where possible, obstacles that cross the full width of outdoor recreation access routes should be separated by 48 inches minimum so individuals who use wheeled mobility devices can cross the obstacle before confronting another obstacle. emcdonald on DSK67QTVN1PROD with RULES2 1016.6 Openings This section requires openings in the surface of outdoor recreation access routes, passing spaces, and resting intervals such as spaces between the boards in a boardwalk and drainage grates to not allow passage of a sphere more than 1⁄2 inch in diameter. Where possible, drainage grates should be located outside the minimum clear width of the recreation access route. Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel. 1016.7 Slopes This section contains technical requirements for the maximum running slope and segment length (1016.7.1) and cross slope (1016.7.2) of outdoor recreation access routes. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 1016.7.1 Maximum Running Slope and Segment Length This section requires the running slope of any segment of an outdoor recreation access route to not be steeper than 1:10 (10%). Where the running slope of a segment of an outdoor recreation access route is steeper than 1:20 (5%), the maximum length of the segment is specified in Table 1016.7.1, and a resting interval is required at the top and bottom of each segment. Gradual running slopes are more useable by individuals with disabilities. Where the terrain results in steeper running slopes, resting intervals are required more frequently. Where running slopes are less severe, resting intervals are permitted to be further apart. 1016.7.2 Cross Slope This section requires the cross slope of outdoor recreation access routes to not be steeper than 1:48. Where the surface is other than asphalt, concrete, or boards, cross slopes not steeper than 1:20 are permitted when necessary for drainage. 1016.8 Resting Intervals This section contains the technical requirements for the length (1016.8.1), width (1016.8.2), and slope (1016.8.3) of resting intervals; and for a turning space (1016.8.4) where resting intervals are provided adjacent to an outdoor recreation access route. 1016.8.1 Length This section requires resting intervals to be 60 inches long minimum. 1016.8.2 Width This section requires resting intervals that are provided within an outdoor recreation access route to be at least as wide as the widest segment of the outdoor recreation access route leading to the resting interval. Resting intervals that are provided adjacent to an outdoor recreation access route are required to be 36 inches wide minimum. 1016.8.3 Slope This section requires the slope of resting intervals to not be steeper than 1:48 in any direction. Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. 1016.8.4 Turning Space This section requires a turning space complying with 304.2.3 of the Architectural Barriers Act Accessibility Guidelines where resting intervals are provided adjacent to an outdoor recreation access route. The vertical PO 00000 Frm 00014 Fmt 4701 Sfmt 4700 alignment of the outdoor recreation access route, turning space, and resting interval is required to be nominally planar (i.e., as flat as possible) so that all the wheels of a mobility device touch the ground when turning into and out of the resting interval. 1016.9 Protruding Objects This section requires constructed elements on outdoor recreation access routes, resting intervals, and passing spaces to comply with the technical requirements for protruding objects in 307 of the Architectural Barriers Act Accessibility Guidelines. Protruding objects can be hazardous for individuals who are blind or have low vision. Signs and other post mounted objects are examples of constructed elements that can be protruding objects. Natural elements such as tree branches are not required to comply with the technical requirements for protruding objects in 307 of the Architectural Barriers Act Accessibility Guidelines. However, entities should maintain the vertical clearance along outdoor recreation access routes, resting intervals, and passing spaces free from tree branches for 80 inches high minimum above the ground. 1017 Trails 1017.1 General This section contains the technical requirements for trails. The technical requirements address the surface of the trails, passing spaces, and resting intervals (1017.2); the clear tread width of trails (1017.3); passing spaces (1017.4); tread obstacles (1017.5); openings (1017.6); slopes, including running slope (1017.7.1) and cross slope (1017.7.2); resting intervals (1017.8); protruding objects (1017.9); and trailhead signs (1017.10). Two exceptions are provided. When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1017 on a portion of a trail, Exception 1 permits the portion of trail to comply with the provision to the extent practicable. When an entity determines that it is impracticable for the entire trail to comply with the technical requirements in 1017, Exception 2 exempts the entire trail from complying with the requirements. This determination is made after the entity applies Exception 1 to portions of the trail. The entity should consider the portions of the trail that can and cannot fully comply with the specific provisions in 1017 and the extent of compliance where full compliance cannot be achieved when determining whether it would be E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations impracticable for the entire trail to comply with the technical requirements in 1017. As discussed under F201.4.1, federal agencies are required to document the basis for their determination when using Exceptions 1 or 2, and are required notify us when using Exception 2. 1017.2 Surface This section requires the surface of trails, passing spaces, and resting intervals to be firm and stable. A firm trail surface resists deformation by indentations. A stable trail surface is not permanently affected by expected weather conditions and can sustain normal wear and tear from the expected uses between planned maintenance. emcdonald on DSK67QTVN1PROD with RULES2 1017.3 Clear Tread Width This section requires the clear tread width of trails to be 36 inches minimum. The 36 inches minimum clear tread width is to be maintained for the entire distance of the trail and may not be reduced by gates, barriers, or other obstacles unless an entity determines under Exception 1 to 1017.1 that a condition in 1019 does not permit full compliance with the provision. Where gates and barriers require wheelchair users to make 90 degree or 180 degree turns, sufficient space should be provided for wheelchair users to make the turns. We and National Institute on Disability and Rehabilitation Research sponsored research to collect anthropometric data from a sample of about 500 individuals who use manual wheelchairs, power wheelchairs, and scooters. The research is known as the Anthropometry of Wheeled Mobility Project and was conducted by the Center for Inclusive Design and Environmental Access in the School of Architecture and Planning, University at Buffalo, The State University of New York. The reports on the Anthropometry of Wheeled Mobility Project are available at: https:// www.udeworld.com/ anthropometrics.html. The reports provide data on turning spaces for manual wheelchairs, power wheelchairs, and scooters. 1017.4 Passing Spaces This section requires passing spaces to be provided at intervals of 1000 feet maximum where the clear tread width of trails is less than 60 inches. Entities should consider providing either 60 inches minimum clear tread width on trails or passing spaces at shorter intervals where the trail is heavily used or where the trail is a boardwalk or otherwise not at the same level as the adjoining ground surface. Where the full VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 length of a trail does not fully comply with the technical requirements in 1017, a passing space is required to be located at the end of the trail segment that fully complies with the technical requirements 1017 to enable individuals who use wheeled mobility devices to turn and exit the trail. Passing spaces are required to be: • A space 60 inches minimum by 60 inches minimum; or • The intersection of two trails providing a T-shaped space complying with 304.3.2 of the Architectural Barriers Act Accessibility Guidelines where the base and the arms of the Tshaped space extend 48 inches minimum beyond the intersection. Where the intersection of two trails serves as a passing space, the vertical alignment of the trails at the intersection that form the T-shaped space is required to be nominally planar (i.e., as flat as possible) so that all the wheels of a mobility device touch the ground when turning into and out of the passing space. Passing spaces and resting intervals are permitted to overlap. Where passing spaces and resting intervals overlap, the technical requirements for resting intervals in 1017.8.3 require the slope of the surface to not be steeper than 1:48 in any direction. Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. Otherwise, passing space surfaces have the same slopes as the adjoining trail tread. 1017.5 Tread Obstacles This section contains technical requirements for tread obstacles on trails, passing spaces, and resting intervals. The vertical alignment of joints in concrete, asphalt, or board surfaces on trails can be tread obstacles. Natural features such as tree roots and rocks within the trail tread also can be obstacles. This section requires obstacles to not exceed 1⁄2 inch in height measured vertically to the highest point. Where the surface is other than concrete, asphalt, or boards, obstacles are permitted to not exceed 2 inches in height measured vertically to the highest point. The frequency of tread obstacles and tread obstacles that cross the full width of the trail tread can make travel difficult for individuals who use wheeled mobility devices. Where possible, tread obstacles that cross the full width of the trail tread should be separated by 48 inches minimum so individuals who use wheeled mobility devices can cross the obstacle before confronting another obstacle. PO 00000 Frm 00015 Fmt 4701 Sfmt 4700 59489 1017.6 Openings This section requires openings in the surface of trails, passing spaces, and resting intervals such as spaces between the boards in a boardwalk to not allow passage of a sphere more than 1⁄2 inch in diameter. Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel. 1017.7 Slopes This section contains technical requirements for the maximum running slope and segment length (1017.7.1) and cross slope (1017.7.2) of trails. 1017.7.1 Maximum Running Slope and Segment Length This section requires that not more than 30 percent of the total length of a trail have a running slope steeper than 1:12 (8.33%), and that the running slope of any segment of a trail not be steeper than 1:8 (12%). Where the running slope of a segment a trail is steeper than 1:20 (5%), the maximum length of the segment is specified in Table 1017.7.1, and a resting interval is required at the top and bottom of each segment. Gradual running slopes are more useable by individuals with disabilities. Where the terrain results in steeper running slopes, resting intervals are required more frequently. Where running slopes are less severe, resting intervals are permitted to be further apart. 1017.7.2 Cross Slope This section requires the cross slope of trails to not be steeper than 1:48. Where the surface is other than asphalt, concrete, or boards, cross slopes not steeper than 1:20 are permitted when necessary for drainage. 1017.8 Resting Intervals This section contains the technical requirements for the length (1017.8.1), width (1017.8.2), and slope (1017.8.3) of resting intervals; and for a turning space (1017.8.4) where resting intervals are provided adjacent to a trail. 1017.8.1 Length This section requires resting intervals to be 60 inches long minimum. 1017.8.2 Width This section requires resting intervals that are provided within the trail tread to be at least as wide as the widest segment of the trail tread leading to the resting interval. Resting intervals that are provided adjacent to the trail tread are required to be 36 inches wide minimum. E:\FR\FM\26SER2.SGM 26SER2 59490 1017.8.3 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations Slope This section requires the slope of resting intervals to not be steeper than 1:48 in any direction. Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. 1017.8.4 Turning Space This section requires a turning space complying with 304.2.3 of the Architectural Barriers Act Accessibility Guidelines where resting intervals are provided adjacent to the trail tread. The vertical alignment of the trail tread, turning space, and resting interval is required to be nominally planar (i.e., as flat as possible) so that all the wheels of a mobility device touch the ground when turning in and out of the resting interval. 1017.9 Protruding Objects This section requires constructed elements on trails, resting intervals, and passing spaces to comply with the technical requirements for protruding objects in 307 of the Architectural Barriers Act Accessibility Guidelines. Protruding objects can be hazardous for individuals who are blind or have low vision. Signs and other post mounted objects are examples of constructed elements that can be protruding objects. Natural elements such as tree branches are not required to comply with the technical requirements for protruding objects in 307 of the Architectural Barriers Act Accessibility Guidelines. However, entities should maintain the vertical clearance along the trail tread, resting intervals, and passing spaces free from tree branches for 80 inches high minimum above the ground. 1017.10 Trailhead Signs emcdonald on DSK67QTVN1PROD with RULES2 This section requires trail information signs at trailheads to include information on the length of the trail or trail segment; surface type; typical and minimum tread width; typical and maximum running slope; and typical and maximum cross slope. This information enables individuals with disabilities to decide whether to hike the trail based on the characteristics of the trail. Entities also should provide information about the accessibility of trails on Web sites. 1018 1018.1 Beach Access Routes General This section contains the technical requirements for beach access routes. The technical requirements address connections (1018.2); surface (1018.3); clear width (1018.4); obstacles (1018.5); openings (1018.6); slopes, including VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 running slope (1018.7.1) and cross slope (1018.7.2); resting intervals (1018.8); protruding objects (1018.9); and dune crossings (1018.10). Three exceptions are provided. When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1018 on a portion of a beach access route, Exception 1 permits the portion of route to comply with the provision to the extent practicable. When an entity determines that it is impracticable to provide a beach access route complying with the technical requirements in 1018, Exception 2 does not require a beach access route. This determination is made after the entity applies Exception 1 to portions of the route. The entity should consider the portions of the beach access route that can and cannot fully comply with the specific provisions in 1018 and the extent of compliance where full compliance cannot be achieved when determining whether it would be impracticable to provide a beach access route complying with the technical requirements in 1018. Exception 3 exempts removable beach access routes from complying with the technical requirements for running slope (1018.7.1) and cross slope (1018.7.2); resting intervals (1018.8); and dune crossings (1018.10). As discussed under F201.4.1, federal agencies are required to document the basis for their determination when using Exceptions 1 or 2, and are required to notify us when using Exception 2. 1018.2 Connections This section requires beach access routes to connect an entry point to the beach to the high tide level at tidal beaches; mean high water level at river beaches; and normal recreation water level at lake, pond, and reservoir beaches. 1018.3 Surface This section requires the surface of beach access routes and resting intervals to be firm and stable. 1018.4 Clear Width This section requires the clear width of beach access routes to be 60 inches minimum to enable individuals who use wheeled mobility devices to pass beach visitors traveling in the opposite direction. An exception permits the clear width of beach access routes that are not removable to be reduced to 48 inches minimum at dune crossings. Where gates or barriers are installed to control access to beaches, the gates or barriers should permit the passage of beach wheelchairs. Beach wheelchairs have large, wide wheels that can roll PO 00000 Frm 00016 Fmt 4701 Sfmt 4700 across sand without sinking. Gates or barriers that have clear openings at least 48 inches wide will accommodate most beach wheelchairs. 1018.5 Obstacles This section contains technical requirements for obstacles on beach access routes and resting intervals. The vertical alignment of boards on a beach access route or removable sections of a beach access route can be obstacles. This section requires obstacles to not exceed 1⁄2 inch in height measured vertically to the highest point. Where the surface is other than concrete, asphalt, or boards, obstacles are permitted to not exceed 1 inch in height measured vertically to the highest point. 1018.6 Openings This section requires openings in the surface of beach access routes and resting intervals such as spaces between boards to not allow passage of a sphere more than 1⁄2 inch in diameter. Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel. 1018.7 Slopes This section contains technical requirements for the maximum running slope and segment length (1018.7.1) and cross slope (1018.7.2) of beach access routes. 1018.7.1 Maximum Running Slope and Segment Length This section requires that the running slope of any segment of a beach access route not be steeper than 1:10 (10%). Where the running slope of a segment a beach access route is steeper than 1:20 (5%), the maximum length of the segment is specified in Table 1018.7.1, and a resting interval is required at the top and bottom of each segment. Gradual running slopes are more useable by individuals with disabilities. Where the terrain results in steeper running slopes, resting intervals are required more frequently. Where running slopes are less severe, resting intervals are permitted to be further apart. 1018.7.2 Cross Slope This section requires the cross slope of beach access routes to not be steeper than 1:48. Where the surface is other than asphalt, concrete, or boards, cross slopes not steeper than 1:20 are permitted when necessary for drainage. E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 1018.8 Resting Intervals This section contains the technical requirements for the size (1018.8.1) and slope (1017.8.2) of resting intervals. 1018.8.1 Size This section requires resting intervals to be 60 inches minimum by 60 inches minimum. 1018.8.2 Slope This section requires the slope of resting intervals to not be steeper than 1:48 in any direction. Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage. 1018.9 Protruding Objects This section requires constructed elements on beach access routes and resting intervals to comply with the technical requirements for protruding objects in 307 of the Architectural Barriers Act Accessibility Guidelines. Protruding objects can be hazardous for individuals who are blind or have low vision. Signs and other post mounted objects are examples of constructed elements that can be protruding objects. 1018.10 Dune Crossings This section requires handrails complying with 505 of the Architectural Barriers Act Accessibility Guidelines and curbs or barriers to be provided where the slope of a beach access route at a dune crossing is steeper than 1:20 (5%). The curbs or barriers are required to prevent the passage of a 2 inch diameter sphere, where any portion of the sphere is within 2 inches of the crossing surface. 1019 Conditions for Exceptions 1019.1 General This section lists the conditions for the exceptions to specific provisions in 1011, 1013, 1014, 1015, 1016, 1017, and 1018. When an entity determines that any of the following conditions does not permit full compliance with the provision, compliance is required to the extent practicable: • Compliance is not practicable due to terrain. • Compliance cannot be accomplished with the prevailing construction practices. • Compliance would fundamentally alter the function or purpose of the facility or the setting. • Compliance is limited or precluded by any of the following laws, or by decisions or opinions issued or agreements executed pursuant to any of the following laws: Endangered Species Act; National Environmental Policy Act; National Historic Preservation Act; Wilderness Act; or other federal, state, or local law the purpose of which is to preserve threatened or endangered species; the environment; or archaeological, cultural, historical, or other significant natural features. The last condition allows the following to be a basis for using the exceptions: • Opinions issued by the Secretary of the Interior pursuant to the Endangered Species Act stating how a federal agency can implement an action without jeopardizing the continued existence of any endangered species or threatened species, or destroying or adversely modifying the habitat of such species (16 U.S.C. 1536 (b) (3) (A)); • Decisions issued by a federal agency pursuant to the National Environmental Policy Act in actions requiring environmental impact statements stating how it will avoid or minimize environmental harm (42 U.S.C. 4332; 40 CFR 1505.2); • Agreements executed or decisions issued by a federal agency pursuant to National Historic Preservation Act stating how it will avoid, minimize, or mitigate adverse effects on historical properties (16 U.S.C. 470f and 470h–2; 36 CFR 800.6 (b) (iv) and 800.7 (c) (4)); and • Provisions in the Wilderness Act that require federal agencies to preserve the wilderness character of designated wilderness areas and prohibit any structure or installation within such areas (16 U.S.C. 1131 (b) and (c)). 59491 7. Regulatory Analyses Executive Order 13563 (Improving Regulation and Regulatory Review) and Executive Order 12866 (Regulatory Planning and Review) This final rule is not a significant regulatory action. We adhered to the principles of regulation in Executive Orders 13563 and 12866. Among other things, Executive Order 13563 directs agencies to propose or adopt a regulation only upon a reasoned determination that its benefits justify its costs; tailor the regulation to impose the least burden on society, consistent with obtaining the regulatory objectives; and, in choosing among alternative regulatory approaches, select those approaches that maximize net benefits. Executive Order 13563 recognizes that some benefits are difficult to quantify and provides that, where appropriate and permitted by law, agencies may consider and discuss qualitatively values that are difficult or impossible to quantify, including equity, human dignity, fairness, and distributive impacts. We prepared a regulatory assessment for the final rule. The regulatory assessment is available at: https:// www.access-board.gov/outdoor (click on Background). The costs and benefits of the final rule are discussed below. Costs The regulatory assessment compares the final rule to the guidelines and standards used by federal agencies for the design of outdoor developed areas without regard to accessibility to determine whether the final rule would result in additional costs. The regulatory assessment shows that the final rule would not result in additional costs for camping facilities and picnic facilities. The regulatory assessment shows that the final rule would result in additional costs for viewing areas, trails, and beach access routes as shown in Table 4. TABLE 4—ADDITIONAL COSTS DUE TO FINAL RULE Viewing Areas ............... emcdonald on DSK67QTVN1PROD with RULES2 Trails ............................. Beach Access Routes .. $2,176 for dual base binocular scopes and $3,380 for a dual base telescopes, if viewing scopes provided at viewing areas. $40,655 per trail mile, if trail would not otherwise meet the technical requirements and the exceptions to the technical requirements do not apply to the trail. $4,497 to $6,530 to purchase roll-out mats for beach access routes, if parking areas, toilet facilities, bathing facilities, and circulation paths serving beaches are constructed or altered or beach nourishment project is undertaken. We estimate the federal agencies would incur $1.2 million additional annual costs due to the final rule for VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 viewing areas, trails, and beach access routes as shown in Table 5. PO 00000 Frm 00017 Fmt 4701 Sfmt 4700 E:\FR\FM\26SER2.SGM 26SER2 59492 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations TABLE 5—ADDITIONAL ANNUAL COSTS FOR FEDERAL AGENCIES Facility Total annual costs Assumptions Viewing Areas .................. $241,971 Trails ................................. 617,956 Beach Access Routes ...... 1 344,662 Fish and Wildlife Service provides a viewing scope over five years at 556 wildlife refuges to enhance visitor experiences. Federal agencies construct 15.2 trail miles per year covered by the scoping requirements in F247 that would not otherwise meet the technical requirements for trails in 1017 and the exceptions in 1017 do not apply to the trails. Federal agencies provide beach access routes at 1,025 beaches over 20 years as parking areas, restrooms, shower facilities, and circulation paths serving the beaches are altered or replaced with new facilities. 1. Estimate is based on higher cost for roll-out mats. emcdonald on DSK67QTVN1PROD with RULES2 Benefits The final rule would increase opportunities for individuals with mobility disabilities to participate in outdoor recreation activities with their families and friends. Participation in outdoor recreation activities provides the following benefits: • Physical health benefits, including reduces obesity, diminishes risk of chronic disease; and increases life expectancy; • Mental health benefits, including reduces depression, relieves stress, and improves quality of life; and • Community and social benefits, including unites families and promotes stewardship.9 The benefits are difficult to quantify, but include important national values recognized in Executive Order 13563 such as equity, human dignity, and fairness. The 2010 Survey of Income and Program Participation (SIPP) sponsored by the U.S. Census Bureau estimates that among the civilian noninstitutionalized population aged 15 and older, 30.6 million persons (12.6%) had limitations associated with ambulatory activities of the lower body.10 This number includes 23.9 million persons (9.9%) who had difficulty walking a quarter of a mile; 22.3 million (9.2%) who have difficulty climbing a flight of stairs; 11.6 million persons (4.8%) who used a cane, crutches, or walker to assist with mobility; and 3.6 million persons (1.5%) who use a wheelchair or scooter. Not all 9 These benefits are documented in California State Parks, The Health and Social Benefits of Recreation, 2005 at: https://www.parks.ca.gov/pages/ 795/files/health_benefits_online_6-1-05.pdf and Geoffrey Godbey, Outdoor Recreation, Health, and Wellness: Understanding and Enhancing the Relationship, 2009 at: https://www.rff.org/rff/ documents/rff-dp-09-21.pdf. 10 Americans with Disabilities: 2010 available at: https://www.census.gov/prod/2012pubs/p70131.pdf. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 these persons are likely to directly benefit from the final rule because some may not participate in outdoor recreational activities. We do not have information to estimate the number of individuals with mobility disabilities who would directly benefit from the final rule. Final Regulatory Flexibility Analysis The Regulatory Flexibility Act requires federal agencies to consider the impacts of their rules on small entities, analyze alternatives that minimize the impacts on small entities, and to make the analysis available to the public. See 5 U.S.C. 604. We certified that the proposed rule would not have a significant economic impact on a substantial number of small entities because it would apply to federal agencies that administer outdoor areas developed for recreational purposes. Therefore, we did not prepare an initial regulatory flexibility analysis for the proposed rule. However, the Architectural Barriers Act also applies to facilities constructed or altered by non-federal entities on behalf of the United States. We prepared a final regulatory flexibility analysis for the final rule to consider the impacts of the final rule on small entities that construct or alter recreation facilities on federal lands on behalf of federal agencies pursuant to a concession contract, partnership agreement, or similar arrangement. Need for and Objective of Final Rule The Architectural Barriers Act requires facilities constructed or altered by or on behalf of federal agencies to be readily accessible to and usable by individuals with disabilities. Certain agencies are required to adopt accessibility standards for the design, construction, and alteration of facilities covered by the Architectural Barriers Act. We are required by section 502 of PO 00000 Frm 00018 Fmt 4701 Sfmt 4700 the Rehabilitation Act to establish and maintain minimum guidelines and requirements for the accessibility standards adopted the federal agencies. We are issuing the final rule pursuant to this authority to establish accessibility guidelines for camping facilities, picnic facilities, viewing areas, trails, and beach access routes constructed or altered by or behalf of federal agencies that administer outdoor developed areas. Significant Issues Raised by Public Comments in Response to the Initial Regulatory Flexibility Analysis As noted above, we certified that the proposed rule would not have a significant economic impact on a substantial number of small entities. Therefore, we did not prepare an initial regulatory flexibility analysis for the proposed rule. Response to Comments Filed by Chief Counsel for Advocacy of the Small Business Administration The Chief Counsel for Advocacy of the Small Business Administration did not file comments on the proposed rule. Small Entities Affected by Rule The final rule affects small entities that construct or alter camping facilities, picnic facilities, viewing areas, trails, and beach facilities on federal lands pursuant to a concession contract, partnership agreement, or similar arrangement with the following federal agencies and their components: U.S. Department of Agriculture (Forest Service), U.S. Department of Defense (Army Corps of Engineers), and U.S. Department of the Interior (Bureau of Land Management, Bureau of Reclamation, Fish and Wildlife Service, National Park Service). Data are not available on the number of small entities that construct or alter camping facilities, picnic facilities, viewing E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations areas, trails, and beach facilities on federal lands pursuant to a concession contract, partnership agreement, or similar arrangement with the federal agencies. Small entities that construct facilities of federal land pursuant to a concession contract with federal agencies can include the costs of the capital improvements, including additional costs due to the final rule, in the contract bids and the costs can be offset in the concession fees paid to the federal agencies. for trails or beach access routes to portions of the trail or route. Compliance Requirements in Final Rule The final rule does not impose a federal intergovernmental mandate or federal private sector mandate as those terms are defined in the Unfunded Mandates Reform Act. Any duties imposed on state, local, or tribal governments or on the private sector arise from participation in a voluntary federal program. The final rule contains scoping and technical requirements for camping facilities, picnic facilities, viewing areas, trails, and beach access routes. Scoping requirements specify what features are required to be accessible and, where multiple features of the same type are provided, how many of the features are required to be accessible. The scoping requirements in the final rule are summarized in Table 1 under Executive Summary. Technical requirements specify the design criteria for accessible features. The technical requirements include design criteria for the following outdoor constructed features: picnic tables, fire rings, grills, fireplaces, wood stoves, trash and recycling receptacles, water hydrants, utility and sewage hookups, outdoor rinsing showers, benches, and viewing scopes. The technical requirements also include design criteria for parking spaces within camping units and picnic units with mobility features; pull-up spaces for recreational vehicles at dump stations; tent pads and tent platforms; camp shelters; viewing areas; outdoor recreation access routes; trails; and beach access routes. emcdonald on DSK67QTVN1PROD with RULES2 Steps To Minimize Significant Economic Impacts on Small Entities 18:25 Sep 25, 2013 Jkt 229001 The final rule does not have federalism implications as defined in Executive Order 13112. The final rule does not have substantial direct effects on the states or on the relationship, or the distribution of power and responsibilities, between the federal government and the states. Unfunded Mandates Reform Act List of Subjects in 36 CFR Part 1191 Buildings and facilities, Civil rights, Incorporation by reference, Individuals with disabilities, Transportation. Karen L. Braitmayer, Chair. For the reasons stated in the preamble, we amend 36 CFR part 1191 as follows: PART 1191—AMERICANS WITH DISABILITIES ACT (ADA) ACCESSIBILITY GUIDELINES FOR BUILDINGS AND FACILITIES; ARCHITECTURAL BARRIERS ACT (ABA) ACCESSIBILITY GUIDELINES 1. The authority citation for 36 CFR part 1191 continues to read as follows: ■ Authority: 29 U.S.C. 792 (b)(3); 42 U.S.C. 12204. 2–3. In § 1191.1, redesignate Note 1 to paragraph (a) as Note 3 and add new Notes 1 and 2 to paragraph (a) and redesignate Notes 1 and 2 to paragraph (b) as Notes 2 and 3 and add new Notes 1 and 4 to paragraph (b) to read as follows: ■ The final rules permits exceptions to the specific provisions in the technical requirements for certain elements and facilities based on the conditions listed in Table 2 under Executive Summary. When an entity determines that a condition does not permit full compliance with a provision, compliance is required to the extent practicable. The final rule allows exemptions for an entire trail or beach access route when an entity determines that is impracticable for a trail to comply with the technical requirements for trails or to provide a beach access route complying with the technical requirements for beach access routes. This determination is made after the entity applies the exceptions for specific provisions in the technical requirements VerDate Mar<15>2010 Executive Order 13132 (Federalism) § 1191.1 Accessibility guidelines. (a) * * * Note 1 to paragraph (a): 1. Advisory sections and figures that illustrate the technical requirements in Appendix D are available on the Internet at: www.accessboard.gov. The advisory sections provide guidance only and do not contain mandatory requirements. Note 2 to paragraph (a): 2. The Department of Justice adopted the 2010 ADA Standards for Accessible Design (2010 Standards) as the regulatory standards for the new construction and alteration of facilities subject to its regulations under the Americans with PO 00000 Frm 00019 Fmt 4701 Sfmt 4700 59493 Disabilities Act (ADA), effective March 15, 2012. 28 CFR 35.151(c)(3), as amended at 75 FR 56163, September 15, 2010; and 28 CFR 36.406(a)(3), as amended at 75 FR 56236, September 15, 2010. For state and local governments, the 2010 Standards consist of the regulations at 28 CFR 35.151 and the versions of Appendices B and D to this part published in the 2009 edition of the Code of Federal Regulations. 28 CFR 35.104. For public accommodations and commercial facilities, the 2010 Standards consist of the regulations at 28 CFR part 36, subpart D and the versions of Appendices B and D to this part published in the 2009 edition of the Code of Federal Regulations. 28 CFR 36.104. Because Appendices B and D to this part, as published in the 2009 edition of the Code of Federal Regulations, were adopted by reference by the Department of Justice as part of the 2010 Standards for new construction and alteration of facilities subject to its ADA regulations, subsequent revisions to Appendices B and D by the Access Board are not included in the 2010 Standards and have no legal effect for facilities subject to its ADA regulations until adopted by the Department of Justice. Therefore, the public is cautioned not to use Appendices B and D to this part published in any edition of the Code of Federal Regulations after 2013, until such time as the later edition is adopted by the Department of Justice as a regulatory standard. Complete copies of the 2010 Standards can be obtained from the Department of Justice’s ADA Web site at: https://www.ada.gov/2010ADAstandards_ index.htm, or by contacting the DOJ Information Line, at: 800–514–0301 (Voice) or 800–514–0383 (TTY). * * * (b) * * * * * Note 1 to paragraph (b): 1. Advisory sections and figures that illustrate the technical requirements in Appendix D are available on the Internet at: www.accessboard.gov. The advisory sections provide guidance only and do not contain mandatory requirements. * * * * * Note 4 to paragraph (b): 4. The Department of Defense adopted by reference Appendices B and D to this part as accessibility standards for the new construction and alteration of its facilities subject to the Architectural Barriers Act, effective October 31, 2008. Deputy Secretary of Defense Memorandum dated October 31, 2008, Access for People with Disabilities [available on the Internet at: https://www.access-board.gov/guidelines-andstandards/buildings-and-sites/about-the-abastandards/background/dod-memorandum]. 4. Revise appendix A to part 1191 to read as follows: ■ Appendix A to Part 1191—Table Of Contents ADA CHAPTER 1: APPLICATION AND ADMINISTRATION 101 Purpose 102 Dimensions for Adults and Children 103 Equivalent Facilitation E:\FR\FM\26SER2.SGM 26SER2 59494 104 105 106 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations Conventions Referenced Standards Definitions ADA CHAPTER 2: SCOPING REQUIREMENTS 201 Application 202 Existing Buildings and Facilities 203 General Exceptions 204 Protruding Objects 205 Operable Parts 206 Accessible Routes 207 Accessible Means of Egress 208 Parking Spaces 209 Passenger Loading Zones and Bus Stops 210 Stairways 211 Drinking Fountains 212 Kitchens, Kitchenettes, and Sinks 213 Toilet Facilities and Bathing Facilities 214 Washing Machines and Clothes Dryers 215 Fire Alarm Systems 216 Signs 217 Telephones 218 Transportation Facilities 219 Assistive Listening Systems 220 Automatic Teller Machines and Fare Machines 221 Assembly Areas 222 Dressing, Fitting, and Locker Rooms 223 Medical Care and Long-Term Care Facilities 224 Transient Lodging Guest Rooms 225 Storage 226 Dining Surfaces and Work Surfaces 227 Sales and Service 228 Depositories, Vending Machines, Change Machines, Mail Boxes, and Fuel Dispensers 229 Windows 230 Two-Way Communication Systems 231 Judicial Facilities 232 Detention Facilities and Correctional Facilities 233 Residential Facilities 234 Amusement Rides 235 Recreational Boating Facilities 236 Exercise Machines and Equipment 237 Fishing Piers and Platforms 238 Golf Facilities 239 Miniature Golf Facilities 240 Play Areas 241 Saunas and Steam Rooms 242 Swimming Pools, Wading Pools, and Spas 243 Shooting Facilities with Firing Positions emcdonald on DSK67QTVN1PROD with RULES2 ABA CHAPTER 1: APPLICATION AND ADMINISTRATION F101 Purpose F102 Dimensions for Adults and Children F103 Modifications and Waivers F104 Conventions F105 Referenced Standards F106 Definitions ABA CHAPTER 2: SCOPING REQUIREMENTS F201 Application F202 Existing Buildings and Facilities F203 General Exceptions F204 Protruding Objects F205 Operable Parts F206 Accessible Routes F207 Accessible Means of Egress F208 Parking Spaces VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 F209 Passenger Loading Zones and Bus Stops F210 Stairways F211 Drinking Fountains F212 Kitchens, Kitchenettes, and Sinks F213 Toilet Facilities and Bathing Facilities F214 Washing Machines and Clothes Dryers F215 Fire Alarm Systems F216 Signs F217 Telephones F218 Transportation Facilities F219 Assistive Listening Systems F220 Automatic Teller Machines and Fare Machines F221 Assembly Areas F222 Dressing, Fitting, and Locker Rooms F223 Medical Care and Long-Term Care Facilities F224 Transient Lodging Guest Rooms F225 Storage F226 Dining Surfaces and Work Surfaces F227 Sales and Service F228 Depositories, Vending Machines, Change Machines, Mail Boxes, and Fuel Dispensers F229 Windows F230 Two-Way Communication Systems F231 Judicial Facilities F232 Detention Facilities and Correctional Facilities F233 Residential Facilities F234 Amusement Rides F235 Recreational Boating Facilities F236 Exercise Machines and Equipment F237 Fishing Piers and Platforms F238 Golf Facilities F239 Miniature Golf Facilities F240 Play Areas F241 Saunas and Steam Rooms F242 Swimming Pools, Wading Pools, and Spas F243 Shooting Facilities with Firing Positions F244 Camping Facilities F245 Picnic Facilities F246 Viewing Areas F247 Trails F248 Beach Access Routes CHAPTER 3: BUILDING BLOCKS 301 General 302 Floor or Ground Surfaces 303 Changes in Level 304 Turning Space 305 Clear Floor or Ground Space 306 Knee and Toe Clearance 307 Protruding Objects 308 Reach Ranges 309 Operable Parts CHAPTER 4: ACCESSIBLE ROUTES 401 General 402 Accessible Routes 403 Walking Surfaces 404 Doors, Doorways, and Gates 405 Ramps 406 Curb Ramps 407 Elevators 408 Limited-Use/Limited-Application Elevators 409 Private Residence Elevators 410 Platform Lifts CHAPTER 5: GENERAL SITE AND BUILDING ELEMENTS 501 General 502 Parking Spaces PO 00000 Frm 00020 Fmt 4701 Sfmt 4700 503 504 505 Passenger Loading Zones Stairways Handrails CHAPTER 6: PLUMBING ELEMENTS AND FACILITIES 601 General 602 Drinking Fountains 603 Toilet and Bathing Rooms 604 Water Closets and Toilet Compartments 605 Urinals 606 Lavatories and Sinks 607 Bathtubs 608 Shower Compartments 609 Grab Bars 610 Seats 611 Washing Machines and Clothes Dryers 612 Saunas and Steam Rooms CHAPTER 7: COMMUNICATION ELEMENTS AND FEATURES 701 General 702 Fire Alarm Systems 703 Signs 704 Telephones 705 Detectable Warnings 706 Assistive Listening Systems 707 Automatic Teller Machines and Fare Machines 708 Two-Way Communication Systems CHAPTER 8: SPECIAL ROOMS, SPACES, AND ELEMENTS 801 General 802 Wheelchair Spaces, Companion Seats, and Designated Aisle Seats 803 Dressing, Fitting, and Locker Rooms 804 Kitchens and Kitchenettes 805 Medical Care and Long-Term Care Facilities 806 Transient Lodging Guest Rooms 807 Holding Cells and Housing Cells 808 Courtrooms 809 Residential Dwelling Units 810 Transportation Facilities 811 Storage CHAPTER 9: BUILT-IN ELEMENTS 901 General 902 Dining Surfaces and Work Surfaces 903 Benches 904 Check-Out Aisles and Sales and Service Counters CHAPTER 10: RECREATION FACILITIES 1001 General 1002 Amusement Rides 1003 Recreational Boating Facilities 1004 Exercise Machines and Equipment 1005 Fishing Piers and Platforms 1006 Golf Facilities 1007 Miniature Golf Facilities 1008 Play Areas 1009 Swimming Pools, Wading Pools, and Spas 1010 Shooting Facilities with Firing Positions 1011 Outdoor Constructed Features 1012 Parking Spaces Within Camping Units and Picnic Units and Pull-Up Spaces at Dump Stations 1013 Tent Pads and Tent Platforms 1014 Camp Shelters 1015 Viewing Areas 1016 Outdoor Recreation Access Routes 1017 Trails 1018 Beach Access Routes E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 1019 Conditions for Exceptions 5. Revise appendix B to part 1191 to read as follows: ■ Appendix B to Part 1191—Americans With Disabilities Act: Scoping ADA CHAPTER 1: APPLICATION AND ADMINISTRATION 101 Purpose 101.1 General. This document contains scoping and technical requirements for accessibility to sites, facilities, buildings, and elements by individuals with disabilities. The requirements are to be applied during the design, construction, additions to, and alteration of sites, facilities, buildings, and elements to the extent required by regulations issued by Federal agencies under the Americans with Disabilities Act of 1990 (ADA). 101.2 Effect on Removal of Barriers in Existing Facilities. This document does not address existing facilities unless altered at the discretion of a covered entity. The Department of Justice has authority over existing facilities that are subject to the requirement for removal of barriers under title III of the ADA. Any determination that this document applies to existing facilities subject to the barrier removal requirement is solely within the discretion of the Department of Justice and is effective only to the extent required by regulations issued by the Department of Justice. 102 Dimensions for Adults and Children 102.1 General. The technical requirements are based on adult dimensions and anthropometrics. In addition, this document includes technical requirements based on children’s dimensions and anthropometrics for drinking fountains, water closets, toilet compartments, lavatories and sinks, dining surfaces, and work surfaces. emcdonald on DSK67QTVN1PROD with RULES2 103 Equivalent Facilitation 103.1 General. Nothing in these requirements prevents the use of designs, products, or technologies as alternatives to those prescribed, provided they result in substantially equivalent or greater accessibility and usability. 104 Conventions 104.1 Dimensions. Dimensions that are not stated as ‘‘maximum’’ or ‘‘minimum’’ are absolute. 104.1.1 Construction and Manufacturing Tolerances. All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points. 104.2 Calculation of Percentages. Where the required number of elements or facilities to be provided is determined by calculations of ratios or percentages and remainders or fractions result, the next greater whole number of such elements or facilities shall be provided. Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 105 Referenced Standards 105.1 General. The standards listed in 105.2 are incorporated by reference in this document and are part of the requirements to the prescribed extent of each such reference. The Director of the Federal Register has approved these standards for incorporation by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies of the referenced standards may be inspected at the Architectural and Transportation Barriers Compliance Board, 1331 F Street NW., Suite 1000, Washington, DC 20004; at the Department of Justice, Civil Rights Division, Disability Rights Section, 1425 New York Avenue NW., Washington, DC 20005; at the Department of Transportation, 1200 New Jersey Avenue SE., Washington, DC 20590; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741–6030, or go to https:// www.archives.gov/federal_register/code_of_ federal_regulations/ibr_locations.html. 105.2 Referenced Standards. The specific edition of the standards listed below are referenced in this document. Where differences occur between this document and the referenced standards, this document applies. 105.2.1 ANSI/BHMA. Copies of the referenced standards may be obtained from the Builders Hardware Manufacturers Association, 355 Lexington Avenue, 15th floor, New York, NY 10017 (https:// www.buildershardware.com). ANSI/BHMA A156.10–1999 American National Standard for Power Operated Pedestrian Doors (see 404.3). ANSI/BHMA A156.19–1997 American National Standard for Power Assist and Low Energy Power Operated Doors (see 404.3, 408.3.2.1, and 409.3.1). ANSI/BHMA A156.19–2002 American National Standard for Power Assist and Low Energy Power Operated Doors (see 404.3, 408.3.2.1, and 409.3.1). 105.2.2 ASME. Copies of the referenced standards may be obtained from the American Society of Mechanical Engineers, Two Park Avenue, New York, New York 10016 (https://www.asme.org). ASME A17.1–2000 Safety Code for Elevators and Escalators, including ASME A17.1a–2002 Addenda and ASME A17.1b– 2003 Addenda (see 407.1, 408.1, 409.1, and 810.9). ASME A18.1–1999 Safety Standard for Platform Lifts and Stairway Chairlifts, including ASME A18.1a–2001 Addenda and ASME A18.1b¶2001 Addenda (see 410.1). ASME A18.1–2003 Safety Standard for Platform Lifts and Stairway Chairlifts, (see 410.1). 105.2.3 ASTM. Copies of the referenced standards may be obtained from the American Society for Testing and Materials, 100 Bar Harbor Drive, West Conshohocken, Pennsylvania 19428 (https://www.astm.org). ASTM F1292–99 Standard Specification for Impact Attenuation of Surface Systems Under and Around Playground Equipment (see 1008.2.6.2). ASTM F1292–04 Standard Specification for Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment (see 1008.2.6.2). PO 00000 Frm 00021 Fmt 4701 Sfmt 4700 59495 ASTM F1487–01 Standard Consumer Safety Performance Specification for Playground Equipment for Public Use (see 106.5). ASTM F1951–99 Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment (see 1008.2.6.1). 105.2.4 ICC/IBC. Copies of the referenced standard may be obtained from the International Code Council, 500 New Jersey Avenue NW., Washington, DC 20001 (www.iccsafe.org). International Building Code, 2000 Edition (see 207.1, 207.2, 216.4.2, 216.4.3, and 1005.2.1). International Building Code, 2001 Supplement (see 207.1 and 207.2). International Building Code, 2003 Edition (see 207.1, 207.2, 216.4.2, 216.4.3, and 1005.2.1). 105.2.5 NFPA. Copies of the referenced standards may be obtained from the National Fire Protection Association, 1 Batterymarch Park, Quincy, Massachusetts 02169 (https:// www.nfpa.org). NFPA 72 National Fire Alarm Code, 1999 Edition (see 702.1 and 809.5.2). NFPA 72 National Fire Alarm Code, 2002 Edition (see 702.1 and 809.5.2). 106 Definitions 106.1 General. For the purpose of this document, the terms defined in 106.5 have the indicated meaning. 106.2 Terms Defined in Referenced Standards. Terms not defined in 106.5 or in regulations issued by the Department of Justice and the Department of Transportation to implement the Americans with Disabilities Act, but specifically defined in a referenced standard, shall have the specified meaning from the referenced standard unless otherwise stated. 106.3 Undefined Terms. The meaning of terms not specifically defined in 106.5 or in regulations issued by the Department of Justice and the Department of Transportation to implement the Americans with Disabilities Act or in referenced standards shall be as defined by collegiate dictionaries in the sense that the context implies. 106.4 Interchangeability. Words, terms and phrases used in the singular include the plural and those used in the plural include the singular. 106.5 Defined Terms. Accessible. A site, building, facility, or portion thereof that complies with this part. Accessible Means of Egress. A continuous and unobstructed way of egress travel from any point in a building or facility that provides an accessible route to an area of refuge, a horizontal exit, or a public way. Addition. An expansion, extension, or increase in the gross floor area or height of a building or facility. Administrative Authority. A governmental agency that adopts or enforces regulations and guidelines for the design, construction, or alteration of buildings and facilities. Alteration. A change to a building or facility that affects or could affect the usability of the building or facility or portion thereof. Alterations include, but are not limited to, remodeling, renovation, E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 59496 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations rehabilitation, reconstruction, historic restoration, resurfacing of circulation paths or vehicular ways, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height partitions. Normal maintenance, reroofing, painting or wallpapering, or changes to mechanical and electrical systems are not alterations unless they affect the usability of the building or facility. Amusement Attraction. Any facility, or portion of a facility, located within an amusement park or theme park which provides amusement without the use of an amusement device. Amusement attractions include, but are not limited to, fun houses, barrels, and other attractions without seats. Amusement Ride. A system that moves persons through a fixed course within a defined area for the purpose of amusement. Amusement Ride Seat. A seat that is builtin or mechanically fastened to an amusement ride intended to be occupied by one or more passengers. Area of Sport Activity. That portion of a room or space where the play or practice of a sport occurs. Assembly Area. A building or facility, or portion thereof, used for the purpose of entertainment, educational or civic gatherings, or similar purposes. For the purposes of these requirements, assembly areas include, but are not limited to, classrooms, lecture halls, courtrooms, public meeting rooms, public hearing rooms, legislative chambers, motion picture houses, auditoria, theaters, playhouses, dinner theaters, concert halls, centers for the performing arts, amphitheaters, arenas, stadiums, grandstands, or convention centers. Assistive Listening System (ALS). An amplification system utilizing transmitters, receivers, and coupling devices to bypass the acoustical space between a sound source and a listener by means of induction loop, radio frequency, infrared, or direct-wired equipment. Boarding Pier. A portion of a pier where a boat is temporarily secured for the purpose of embarking or disembarking. Boat Launch Ramp. A sloped surface designed for launching and retrieving trailered boats and other water craft to and from a body of water. Boat Slip. That portion of a pier, main pier, finger pier, or float where a boat is moored for the purpose of berthing, embarking, or disembarking. Building. Any structure used or intended for supporting or sheltering any use or occupancy. Catch Pool. A pool or designated section of a pool used as a terminus for water slide flumes. Characters. Letters, numbers, punctuation marks and typographic symbols. Children’s Use. Describes spaces and elements specifically designed for use primarily by people 12 years old and younger. Circulation Path. An exterior or interior way of passage provided for pedestrian travel, including but not limited to, walks, hallways, courtyards, elevators, platform lifts, ramps, stairways, and landings. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 Closed-Circuit Telephone. A telephone with a dedicated line such as a house phone, courtesy phone or phone that must be used to gain entry to a facility. Common Use. Interior or exterior circulation paths, rooms, spaces, or elements that are not for public use and are made available for the shared use of two or more people. Cross Slope. The slope that is perpendicular to the direction of travel (see running slope). Curb Ramp. A short ramp cutting through a curb or built up to it. Detectable Warning. A standardized surface feature built in or applied to walking surfaces or other elements to warn of hazards on a circulation path. Element. An architectural or mechanical component of a building, facility, space, or site. Elevated Play Component. A play component that is approached above or below grade and that is part of a composite play structure consisting of two or more play components attached or functionally linked to create an integrated unit providing more than one play activity. Employee Work Area. All or any portion of a space used only by employees and used only for work. Corridors, toilet rooms, kitchenettes and break rooms are not employee work areas. Entrance. Any access point to a building or portion of a building or facility used for the purpose of entering. An entrance includes the approach walk, the vertical access leading to the entrance platform, the entrance platform itself, vestibule if provided, the entry door or gate, and the hardware of the entry door or gate. Facility. All or any portion of buildings, structures, site improvements, elements, and pedestrian routes or vehicular ways located on a site. Gangway. A variable-sloped pedestrian walkway that links a fixed structure or land with a floating structure. Gangways that connect to vessels are not addressed by this document. Golf Car Passage. A continuous passage on which a motorized golf car can operate. Ground Level Play Component. A play component that is approached and exited at the ground level. Key Station. Rapid and light rail stations, and commuter rail stations, as defined under criteria established by the Department of Transportation in 49 CFR 37.47 and 49 CFR 37.51, respectively. Mail Boxes. Receptacles for the receipt of documents, packages, or other deliverable matter. Mail boxes include, but are not limited to, post office boxes and receptacles provided by commercial mail-receiving agencies, apartment facilities, or schools. Marked Crossing. A crosswalk or other identified path intended for pedestrian use in crossing a vehicular way. Mezzanine. An intermediate level or levels between the floor and ceiling of any story with an aggregate floor area of not more than one-third of the area of the room or space in which the level or levels are located. Mezzanines have sufficient elevation that space for human occupancy can be provided on the floor below. PO 00000 Frm 00022 Fmt 4701 Sfmt 4700 Occupant Load. The number of persons for which the means of egress of a building or portion of a building is designed. Operable Part. A component of an element used to insert or withdraw objects, or to activate, deactivate, or adjust the element. Pictogram. A pictorial symbol that represents activities, facilities, or concepts. Play Area. A portion of a site containing play components designed and constructed for children. Play Component. An element intended to generate specific opportunities for play, socialization, or learning. Play components are manufactured or natural; and are standalone or part of a composite play structure. Private Building or Facility. A place of public accommodation or a commercial building or facility subject to title III of the ADA and 28 CFR part 36 or a transportation building or facility subject to title III of the ADA and 49 CFR 37.45. Public Building or Facility. A building or facility or portion of a building or facility designed, constructed, or altered by, on behalf of, or for the use of a public entity subject to title II of the ADA and 28 CFR part 35 or to title II of the ADA and 49 CFR 37.41 or 37.43. Public Entrance. An entrance that is not a service entrance or a restricted entrance. Public Use. Interior or exterior rooms, spaces, or elements that are made available to the public. Public use may be provided at a building or facility that is privately or publicly owned. Public Way. Any street, alley or other parcel of land open to the outside air leading to a public street, which has been deeded, dedicated or otherwise permanently appropriated to the public for public use and which has a clear width and height of not less than 10 feet (3050 mm). Qualified Historic Building or Facility. A building or facility that is listed in or eligible for listing in the National Register of Historic Places, or designated as historic under an appropriate State or local law. Ramp. A walking surface that has a running slope steeper than 1:20. Residential Dwelling Unit. A unit intended to be used as a residence, that is primarily long-term in nature. Residential dwelling units do not include transient lodging, inpatient medical care, licensed long-term care, and detention or correctional facilities. Restricted Entrance. An entrance that is made available for common use on a controlled basis but not public use and that is not a service entrance. Running Slope. The slope that is parallel to the direction of travel (see cross slope). Self-Service Storage. Building or facility designed and used for the purpose of renting or leasing individual storage spaces to customers for the purpose of storing and removing personal property on a self-service basis. Service Entrance. An entrance intended primarily for delivery of goods or services. Site. A parcel of land bounded by a property line or a designated portion of a public right-of-way. Soft Contained Play Structure. A play structure made up of one or more play components where the user enters a fully E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations enclosed play environment that utilizes pliable materials, such as plastic, netting, or fabric. Space. A definable area, such as a room, toilet room, hall, assembly area, entrance, storage room, alcove, courtyard, or lobby. Story. That portion of a building or facility designed for human occupancy included between the upper surface of a floor and upper surface of the floor or roof next above. A story containing one or more mezzanines has more than one floor level. Structural Frame. The columns and the girders, beams, and trusses having direct connections to the columns and all other members that are essential to the stability of the building or facility as a whole. Tactile. An object that can be perceived using the sense of touch. Technically Infeasible. With respect to an alteration of a building or a facility, something that has little likelihood of being accomplished because existing structural conditions would require removing or altering a loadbearing member that is an essential part of the structural frame; or because other existing physical or site constraints prohibit modification or addition of elements, spaces, or features that are in full and strict compliance with the minimum requirements. Teeing Ground. In golf, the starting place for the hole to be played. Transfer Device. Equipment designed to facilitate the transfer of a person from a wheelchair or other mobility aid to and from an amusement ride seat. Transient Lodging. A building or facility containing one or more guest room(s) for sleeping that provides accommodations that are primarily short-term in nature. Transient lodging does not include residential dwelling units intended to be used as a residence, inpatient medical care facilities, licensed long-term care facilities, detention or correctional facilities, or private buildings or facilities that contain not more than five rooms for rent or hire and that are actually occupied by the proprietor as the residence of such proprietor. Transition Plate. A sloping pedestrian walking surface located at the end(s) of a gangway. TTY. An abbreviation for teletypewriter. Machinery that employs interactive textbased communication through the transmission of coded signals across the telephone network. TTYs may include, for example, devices known as TDDs (telecommunication display devices or telecommunication devices for deaf persons) or computers with special modems. TTYs are also called text telephones. Use Zone. The ground level area beneath and immediately adjacent to a play structure or play equipment that is designated by ASTM F1487 (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1) for unrestricted circulation around the play equipment and where it is predicted that a user would land when falling from or exiting the play equipment. Vehicular Way. A route provided for vehicular traffic, such as in a street, driveway, or parking facility. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 Walk. An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts. Wheelchair Space. Space for a single wheelchair and its occupant. Work Area Equipment. Any machine, instrument, engine, motor, pump, conveyor, or other apparatus used to perform work. As used in this document, this term shall apply only to equipment that is permanently installed or built-in in employee work areas. Work area equipment does not include passenger elevators and other accessible means of vertical transportation. ADA CHAPTER 2: SCOPING REQUIREMENTS 201 Application 201.1 Scope. All areas of newly designed and newly constructed buildings and facilities and altered portions of existing buildings and facilities shall comply with these requirements. 201.2 Application Based on Building or Facility Use. Where a site, building, facility, room, or space contains more than one use, each portion shall comply with the applicable requirements for that use. 201.3 Temporary and Permanent Structures. These requirements shall apply to temporary and permanent buildings and facilities. 202 Existing Buildings and Facilities 202.1 General. Additions and alterations to existing buildings or facilities shall comply with 202. 202.2 Additions. Each addition to an existing building or facility shall comply with the requirements for new construction. Each addition that affects or could affect the usability of or access to an area containing a primary function shall comply with 202.4. 202.3 Alterations. Where existing elements or spaces are altered, each altered element or space shall comply with the applicable requirements of Chapter 2. EXCEPTIONS: 1. Unless required by 202.4, where elements or spaces are altered and the circulation path to the altered element or space is not altered, an accessible route shall not be required. 2. In alterations, where compliance with applicable requirements is technically infeasible, the alteration shall comply with the requirements to the maximum extent feasible. 3. Residential dwelling units not required to be accessible in compliance with a standard issued pursuant to the Americans with Disabilities Act or Section 504 of the Rehabilitation Act of 1973, as amended, shall not be required to comply with 202.3. 202.3.1 Prohibited Reduction in Access. An alteration that decreases or has the effect of decreasing the accessibility of a building or facility below the requirements for new construction at the time of the alteration is prohibited. 202.3.2 Extent of Application. An alteration of an existing element, space, or area of a building or facility shall not impose a requirement for accessibility greater than required for new construction. 202.4 Alterations Affecting Primary Function Areas. In addition to the PO 00000 Frm 00023 Fmt 4701 Sfmt 4700 59497 requirements of 202.3, an alteration that affects or could affect the usability of or access to an area containing a primary function shall be made so as to ensure that, to the maximum extent feasible, the path of travel to the altered area, including the rest rooms, telephones, and drinking fountains serving the altered area, are readily accessible to and usable by individuals with disabilities, unless such alterations are disproportionate to the overall alterations in terms of cost and scope as determined under criteria established by the Attorney General. In existing transportation facilities, an area of primary function shall be as defined under regulations published by the Secretary of the Department of Transportation or the Attorney General. EXCEPTION: Residential dwelling units shall not be required to comply with 202.4. 202.5 Alterations to Qualified Historic Buildings and Facilities. Alterations to a qualified historic building or facility shall comply with 202.3 and 202.4. EXCEPTION: Where the State Historic Preservation Officer or Advisory Council on Historic Preservation determines that compliance with the requirements for accessible routes, entrances, or toilet facilities would threaten or destroy the historic significance of the building or facility, the exceptions for alterations to qualified historic buildings or facilities for that element shall be permitted to apply. 203 General Exceptions 203.1 General. Sites, buildings, facilities, and elements are exempt from these requirements to the extent specified by 203. 203.2 Construction Sites. Structures and sites directly associated with the actual processes of construction, including but not limited to, scaffolding, bridging, materials hoists, materials storage, and construction trailers shall not be required to comply with these requirements or to be on an accessible route. Portable toilet units provided for use exclusively by construction personnel on a construction site shall not be required to comply with 213 or to be on an accessible route. 203.3 Raised Areas. Areas raised primarily for purposes of security, life safety, or fire safety, including but not limited to, observation or lookout galleries, prison guard towers, fire towers, or life guard stands shall not be required to comply with these requirements or to be on an accessible route. 203.4 Limited Access Spaces. Spaces accessed only by ladders, catwalks, crawl spaces, or very narrow passageways shall not be required to comply with these requirements or to be on an accessible route. 203.5 Machinery Spaces. Spaces frequented only by service personnel for maintenance, repair, or occasional monitoring of equipment shall not be required to comply with these requirements or to be on an accessible route. Machinery spaces include, but are not limited to, elevator pits or elevator penthouses; mechanical, electrical or communications equipment rooms; piping or equipment catwalks; water or sewage treatment pump rooms and stations; electric substations and transformer vaults; and highway and tunnel utility facilities. E:\FR\FM\26SER2.SGM 26SER2 59498 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 203.6 Single Occupant Structures. Single occupant structures accessed only by passageways below grade or elevated above standard curb height, including but not limited to, toll booths that are accessed only by underground tunnels, shall not be required to comply with these requirements or to be on an accessible route. 203.7 Detention and Correctional Facilities. In detention and correctional facilities, common use areas that are used only by inmates or detainees and security personnel and that do not serve holding cells or housing cells required to comply with 232, shall not be required to comply with these requirements or to be on an accessible route. 203.8 Residential Facilities. In residential facilities, common use areas that do not serve residential dwelling units required to provide mobility features complying with 809.2 through 809.4 shall not be required to comply with these requirements or to be on an accessible route. 203.9 Employee Work Areas. Spaces and elements within employee work areas shall only be required to comply with 206.2.8, 207.1, and 215.3 and shall be designed and constructed so that individuals with disabilities can approach, enter, and exit the employee work area. Employee work areas, or portions of employee work areas, other than raised courtroom stations, that are less than 300 square feet (28 m2) and elevated 7 inches (180 mm) or more above the finish floor or ground where the elevation is essential to the function of the space shall not be required to comply with these requirements or to be on an accessible route. 203.10 Raised Refereeing, Judging, and Scoring Areas. Raised structures used solely for refereeing, judging, or scoring a sport shall not be required to comply with these requirements or to be on an accessible route. 203.11 Water Slides. Water slides shall not be required to comply with these requirements or to be on an accessible route. 203.12 Animal Containment Areas. Animal containment areas that are not for public use shall not be required to comply with these requirements or to be on an accessible route. 203.13 Raised Boxing or Wrestling Rings. Raised boxing or wrestling rings shall not be required to comply with these requirements or to be on an accessible route. 203.14 Raised Diving Boards and Diving Platforms. Raised diving boards and diving platforms shall not be required to comply with these requirements or to be on an accessible route. 204 Protruding Objects 204.1 General. Protruding objects on circulation paths shall comply with 307. EXCEPTIONS: 1. Within areas of sport activity, protruding objects on circulation paths shall not be required to comply with 307. 2. Within play areas, protruding objects on circulation paths shall not be required to comply with 307 provided that ground level accessible routes provide vertical clearance in compliance with 1008.2. 205 Operable Parts 205.1 General. Operable parts on accessible elements, accessible routes, and in VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 accessible rooms and spaces shall comply with 309. EXCEPTIONS: 1. Operable parts that are intended for use only by service or maintenance personnel shall not be required to comply with 309. 2. Electrical or communication receptacles serving a dedicated use shall not be required to comply with 309. 3. Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309. 4. Floor electrical receptacles shall not be required to comply with 309. 5. HVAC diffusers shall not be required to comply with 309. 6. Except for light switches, where redundant controls are provided for a single element, one control in each space shall not be required to comply with 309. 7. Cleats and other boat securement devices shall not be required to comply with 309.3. 8. Exercise machines and exercise equipment shall not be required to comply with 309. 206 Accessible Routes 206.1 General. Accessible routes shall be provided in accordance with 206 and shall comply with Chapter 4. 206.2 Where Required. Accessible routes shall be provided where required by 206.2. 206.2.1 Site Arrival Points. At least one accessible route shall be provided within the site from accessible parking spaces and accessible passenger loading zones; public streets and sidewalks; and public transportation stops to the accessible building or facility entrance they serve. EXCEPTIONS: 1. Where exceptions for alterations to qualified historic buildings or facilities are permitted by 202.5, no more than one accessible route from a site arrival point to an accessible entrance shall be required. 2. An accessible route shall not be required between site arrival points and the building or facility entrance if the only means of access between them is a vehicular way not providing pedestrian access. 206.2.2 Within a Site. At least one accessible route shall connect accessible buildings, accessible facilities, accessible elements, and accessible spaces that are on the same site. EXCEPTION: An accessible route shall not be required between accessible buildings, accessible facilities, accessible elements, and accessible spaces if the only means of access between them is a vehicular way not providing pedestrian access. 206.2.3 Multi-Story Buildings and Facilities. At least one accessible route shall connect each story and mezzanine in multistory buildings and facilities. EXCEPTIONS: 1. In private buildings or facilities that are less than three stories or that have less than 3000 square feet (279 m2) per story, an accessible route shall not be required to connect stories provided that the building or facility is not a shopping center, a shopping mall, the professional office of a health care provider, a terminal, depot or PO 00000 Frm 00024 Fmt 4701 Sfmt 4700 other station used for specified public transportation, an airport passenger terminal, or another type of facility as determined by the Attorney General. 2. Where a two-story public building or facility has one story with an occupant load of five or fewer persons that does not contain public use space, that story shall not be required to be connected to the story above or below. 3. In detention and correctional facilities, an accessible route shall not be required to connect stories where cells with mobility features required to comply with 807.2, all common use areas serving cells with mobility features required to comply with 807.2, and all public use areas are on an accessible route. 4. In residential facilities, an accessible route shall not be required to connect stories where residential dwelling units with mobility features required to comply with 809.2 through 809.4, all common use areas serving residential dwelling units with mobility features required to comply with 809.2 through 809.4, and public use areas serving residential dwelling units are on an accessible route. 5. Within multi-story transient lodging guest rooms with mobility features required to comply with 806.2, an accessible route shall not be required to connect stories provided that spaces complying with 806.2 are on an accessible route and sleeping accommodations for two persons minimum are provided on a story served by an accessible route. 6. In air traffic control towers, an accessible route shall not be required to serve the cab and the floor immediately below the cab. 7. Where exceptions for alterations to qualified historic buildings or facilities are permitted by 202.5, an accessible route shall not be required to stories located above or below the accessible story. 206.2.3.1 Stairs and Escalators in Existing Buildings. In alterations and additions, where an escalator or stair is provided where none existed previously and major structural modifications are necessary for the installation, an accessible route shall be provided between the levels served by the escalator or stair unless exempted by 206.2.3 Exceptions 1 through 7. 206.2.4 Spaces and Elements. At least one accessible route shall connect accessible building or facility entrances with all accessible spaces and elements within the building or facility which are otherwise connected by a circulation path unless exempted by 206.2.3 Exceptions 1 through 7. EXCEPTIONS: 1. Raised courtroom stations, including judges’ benches, clerks’ stations, bailiffs’ stations, deputy clerks’ stations, and court reporters’ stations shall not be required to provide vertical access provided that the required clear floor space, maneuvering space, and, if appropriate, electrical service are installed at the time of initial construction to allow future installation of a means of vertical access complying with 405, 407, 408, or 410 without requiring substantial reconstruction of the space. 2. In assembly areas with fixed seating required to comply with 221, an accessible E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations route shall not be required to serve fixed seating where wheelchair spaces required to be on an accessible route are not provided. 3. Accessible routes shall not be required to connect mezzanines where buildings or facilities have no more than one story. In addition, accessible routes shall not be required to connect stories or mezzanines where multi-story buildings or facilities are exempted by 206.2.3 Exceptions 1 through 7. 206.2.5 Restaurants and Cafeterias. In restaurants and cafeterias, an accessible route shall be provided to all dining areas, including raised or sunken dining areas, and outdoor dining areas. EXCEPTIONS: 1. In buildings or facilities not required to provide an accessible route between stories, an accessible route shall not be required to a mezzanine dining area where the mezzanine contains less than 25 percent of the total combined area for seating and dining and where the same decor and services are provided in the accessible area. 2. In alterations, an accessible route shall not be required to existing raised or sunken dining areas, or to all parts of existing outdoor dining areas where the same services and decor are provided in an accessible space usable by the public and not restricted to use by people with disabilities. 3. In sports facilities, tiered dining areas providing seating required to comply with 221 shall be required to have accessible routes serving at least 25 percent of the dining area provided that accessible routes serve seating complying with 221 and each tier is provided with the same services. 206.2.6 Performance Areas. Where a circulation path directly connects a performance area to an assembly seating area, an accessible route shall directly connect the assembly seating area with the performance area. An accessible route shall be provided from performance areas to ancillary areas or facilities used by performers unless exempted by 206.2.3 Exceptions 1 through 7. 206.2.7 Press Boxes. Press boxes in assembly areas shall be on an accessible route. EXCEPTIONS: 1. An accessible route shall not be required to press boxes in bleachers that have points of entry at only one level provided that the aggregate area of all press boxes is 500 square feet (46 m2) maximum. 2. An accessible route shall not be required to free-standing press boxes that are elevated above grade 12 feet (3660 mm) minimum provided that the aggregate area of all press boxes is 500 square feet (46 m2) maximum. 206.2.8 Employee Work Areas. Common use circulation paths within employee work areas shall comply with 402. EXCEPTIONS: 1. Common use circulation paths located within employee work areas that are less than 1000 square feet (93 m2) and defined by permanently installed partitions, counters, casework, or furnishings shall not be required to comply with 402. 2. Common use circulation paths located within employee work areas that are an integral component of work area equipment shall not be required to comply with 402. 3. Common use circulation paths located within exterior employee work areas that are fully exposed to the weather shall not be required to comply with 402. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 206.2.9 Amusement Rides. Amusement rides required to comply with 234 shall provide accessible routes in accordance with 206.2.9. Accessible routes serving amusement rides shall comply with Chapter 4 except as modified by 1002.2. 206.2.9.1 Load and Unload Areas. Load and unload areas shall be on an accessible route. Where load and unload areas have more than one loading or unloading position, at least one loading and unloading position shall be on an accessible route. 206.2.9.2 Wheelchair Spaces, Ride Seats Designed for Transfer, and Transfer Devices. When amusement rides are in the load and unload position, wheelchair spaces complying with 1002.4, amusement ride seats designed for transfer complying with 1002.5, and transfer devices complying with 1002.6 shall be on an accessible route. 206.2.10 Recreational Boating Facilities. Boat slips required to comply with 235.2 and boarding piers at boat launch ramps required to comply with 235.3 shall be on an accessible route. Accessible routes serving recreational boating facilities shall comply with Chapter 4, except as modified by 1003.2. 206.2.11 Bowling Lanes. Where bowling lanes are provided, at least 5 percent, but no fewer than one of each type of bowling lane, shall be on an accessible route. 206.2.12 Court Sports. In court sports, at least one accessible route shall directly connect both sides of the court. 206.2.13 Exercise Machines and Equipment. Exercise machines and equipment required to comply with 236 shall be on an accessible route. 206.2.14 Fishing Piers and Platforms. Fishing piers and platforms shall be on an accessible route. Accessible routes serving fishing piers and platforms shall comply with Chapter 4 except as modified by 1005.1. 206.2.15 Golf Facilities. At least one accessible route shall connect accessible elements and spaces within the boundary of the golf course. In addition, accessible routes serving golf car rental areas; bag drop areas; course weather shelters complying with 238.2.3; course toilet rooms; and practice putting greens, practice teeing grounds, and teeing stations at driving ranges complying with 238.3 shall comply with Chapter 4 except as modified by 1006.2. EXCEPTION: Golf car passages complying with 1006.3 shall be permitted to be used for all or part of accessible routes required by 206.2.15. 206.2.16 Miniature Golf Facilities. Holes required to comply with 239.2, including the start of play, shall be on an accessible route. Accessible routes serving miniature golf facilities shall comply with Chapter 4 except as modified by 1007.2. 206.2.17 Play Areas. Play areas shall provide accessible routes in accordance with 206.2.17. Accessible routes serving play areas shall comply with Chapter 4 except as modified by 1008.2. 206.2.17.1 Ground Level and Elevated Play Components. At least one accessible route shall be provided within the play area. The accessible route shall connect ground level play components required to comply with 240.2.1 and elevated play components PO 00000 Frm 00025 Fmt 4701 Sfmt 4700 59499 required to comply with 240.2.2, including entry and exit points of the play components. 206.2.17.2 Soft Contained Play Structures. Where three or fewer entry points are provided for soft contained play structures, at least one entry point shall be on an accessible route. Where four or more entry points are provided for soft contained play structures, at least two entry points shall be on an accessible route. 206.3 Location. Accessible routes shall coincide with or be located in the same area as general circulation paths. Where circulation paths are interior, required accessible routes shall also be interior. 206.4 Entrances. Entrances shall be provided in accordance with 206.4. Entrance doors, doorways, and gates shall comply with 404 and shall be on an accessible route complying with 402. EXCEPTIONS: 1. Where an alteration includes alterations to an entrance, and the building or facility has another entrance complying with 404 that is on an accessible route, the altered entrance shall not be required to comply with 206.4 unless required by 202.4. 2. Where exceptions for alterations to qualified historic buildings or facilities are permitted by 202.5, no more than one public entrance shall be required to comply with 206.4. Where no public entrance can comply with 206.4 under criteria established in 202.5 Exception, then either an unlocked entrance not used by the public shall comply with 206.4; or a locked entrance complying with 206.4 with a notification system or remote monitoring shall be provided. 206.4.1 Public Entrances. In addition to entrances required by 206.4.2 through 206.4.9, at least 60 percent of all public entrances shall comply with 404. 206.4.2 Parking Structure Entrances. Where direct access is provided for pedestrians from a parking structure to a building or facility entrance, each direct access to the building or facility entrance shall comply with 404. 206.4.3 Entrances from Tunnels or Elevated Walkways. Where direct access is provided for pedestrians from a pedestrian tunnel or elevated walkway to a building or facility, at least one direct entrance to the building or facility from each tunnel or walkway shall comply with 404. 206.4.4 Transportation Facilities. In addition to the requirements of 206.4.2, 206.4.3, and 206.4.5 through 206.4.9, transportation facilities shall provide entrances in accordance with 206.4.4. 206.4.4.1 Location. In transportation facilities, where different entrances serve different transportation fixed routes or groups of fixed routes, at least one public entrance serving each fixed route or group of fixed routes shall comply with 404. EXCEPTION: Entrances to key stations and existing intercity rail stations retrofitted in accordance with 49 CFR 37.49 or 49 CFR 37.51 shall not be required to comply with 206.4.4.1. 206.4.4.2 Direct Connections. Direct connections to other facilities shall provide an accessible route complying with 404 from the point of connection to boarding platforms and all transportation system elements E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 59500 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations required to be accessible. Any elements provided to facilitate future direct connections shall be on an accessible route connecting boarding platforms and all transportation system elements required to be accessible. EXCEPTION: In key stations and existing intercity rail stations, existing direct connections shall not be required to comply with 404. 206.4.4.3 Key Stations and Intercity Rail Stations. Key stations and existing intercity rail stations required by Subpart C of 49 CFR part 37 to be altered, shall have at least one entrance complying with 404. 206.4.5 Tenant Spaces. At least one accessible entrance to each tenancy in a facility shall comply with 404. EXCEPTION: Self-service storage facilities not required to comply with 225.3 shall not be required to be on an accessible route. 206.4.6 Residential Dwelling Unit Primary Entrance. In residential dwelling units, at least one primary entrance shall comply with 404. The primary entrance to a residential dwelling unit shall not be to a bedroom. 206.4.7 Restricted Entrances. Where restricted entrances are provided to a building or facility, at least one restricted entrance to the building or facility shall comply with 404. 206.4.8 Service Entrances. If a service entrance is the only entrance to a building or to a tenancy in a facility, that entrance shall comply with 404. 206.4.9 Entrances for Inmates or Detainees. Where entrances used only by inmates or detainees and security personnel are provided at judicial facilities, detention facilities, or correctional facilities, at least one such entrance shall comply with 404. 206.5 Doors, Doorways, and Gates. Doors, doorways, and gates providing user passage shall be provided in accordance with 206.5. 206.5.1 Entrances. Each entrance to a building or facility required to comply with 206.4 shall have at least one door, doorway, or gate complying with 404. 206.5.2 Rooms and Spaces. Within a building or facility, at least one door, doorway, or gate serving each room or space complying with these requirements shall comply with 404. 206.5.3 Transient Lodging Facilities. In transient lodging facilities, entrances, doors, and doorways providing user passage into and within guest rooms that are not required to provide mobility features complying with 806.2 shall comply with 404.2.3. EXCEPTION: Shower and sauna doors in guest rooms that are not required to provide mobility features complying with 806.2 shall not be required to comply with 404.2.3. 206.5.4 Residential Dwelling Units. In residential dwelling units required to provide mobility features complying with 809.2 through 809.4, all doors and doorways providing user passage shall comply with 404. 206.6 Elevators. Elevators provided for passengers shall comply with 407. Where multiple elevators are provided, each elevator shall comply with 407. EXCEPTIONS: 1. In a building or facility permitted to use the exceptions to 206.2.3 or VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 permitted by 206.7 to use a platform lift, elevators complying with 408 shall be permitted. 2. Elevators complying with 408 or 409 shall be permitted in multi-story residential dwelling units. 206.6.1 Existing Elevators. Where elements of existing elevators are altered, the same element shall also be altered in all elevators that are programmed to respond to the same hall call control as the altered elevator and shall comply with the requirements of 407 for the altered element. 206.7 Platform Lifts. Platform lifts shall comply with 410. Platform lifts shall be permitted as a component of an accessible route in new construction in accordance with 206.7. Platform lifts shall be permitted as a component of an accessible route in an existing building or facility. 206.7.1 Performance Areas and Speakers’ Platforms. Platform lifts shall be permitted to provide accessible routes to performance areas and speakers’ platforms. 206.7.2 Wheelchair Spaces. Platform lifts shall be permitted to provide an accessible route to comply with the wheelchair space dispersion and line-of-sight requirements of 221 and 802. 206.7.3 Incidental Spaces. Platform lifts shall be permitted to provide an accessible route to incidental spaces which are not public use spaces and which are occupied by five persons maximum. 206.7.4 Judicial Spaces. Platform lifts shall be permitted to provide an accessible route to: jury boxes and witness stands; raised courtroom stations including, judges’ benches, clerks’ stations, bailiffs’ stations, deputy clerks’ stations, and court reporters’ stations; and to depressed areas such as the well of a court. 206.7.5 Existing Site Constraints. Platform lifts shall be permitted where existing exterior site constraints make use of a ramp or elevator infeasible. 206.7.6 Guest Rooms and Residential Dwelling Units. Platform lifts shall be permitted to connect levels within transient lodging guest rooms required to provide mobility features complying with 806.2 or residential dwelling units required to provide mobility features complying with 809.2 through 809.4. 206.7.7 Amusement Rides. Platform lifts shall be permitted to provide accessible routes to load and unload areas serving amusement rides. 206.7.8 Play Areas. Platform lifts shall be permitted to provide accessible routes to play components or soft contained play structures. 206.7.9 Team or Player Seating. Platform lifts shall be permitted to provide accessible routes to team or player seating areas serving areas of sport activity. 206.7.10 Recreational Boating Facilities and Fishing Piers and Platforms. Platform lifts shall be permitted to be used instead of gangways that are part of accessible routes serving recreational boating facilities and fishing piers and platforms. 206.8 Security Barriers. Security barriers, including but not limited to, security bollards and security check points, shall not obstruct a required accessible route or accessible means of egress. PO 00000 Frm 00026 Fmt 4701 Sfmt 4700 EXCEPTION: Where security barriers incorporate elements that cannot comply with these requirements such as certain metal detectors, fluoroscopes, or other similar devices, the accessible route shall be permitted to be located adjacent to security screening devices. The accessible route shall permit persons with disabilities passing around security barriers to maintain visual contact with their personal items to the same extent provided others passing through the security barrier. 207 Accessible Means of Egress 207.1 General. Means of egress shall comply with section 1003.2.13 of the International Building Code (2000 edition and 2001 Supplement) or section 1007 of the International Building Code (2003 edition) (incorporated by reference, see Referenced Standards’’ in Chapter 1). EXCEPTIONS: 1. Where means of egress are permitted by local building or life safety codes to share a common path of egress travel, accessible means of egress shall be permitted to share a common path of egress travel. 2. Areas of refuge shall not be required in detention and correctional facilities. 207.2 Platform Lifts. Standby power shall be provided for platform lifts permitted by section 1003.2.13.4 of the International Building Code (2000 edition and 2001 Supplement) or section 1007.5 of the International Building Code (2003 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1) to serve as a part of an accessible means of egress. 208 Parking Spaces 208.1 General. Where parking spaces are provided, parking spaces shall be provided in accordance with 208. EXCEPTION: Parking spaces used exclusively for buses, trucks, other delivery vehicles, law enforcement vehicles, or vehicular impound shall not be required to comply with 208 provided that lots accessed by the public are provided with a passenger loading zone complying with 503. 208.2 Minimum Number. Parking spaces complying with 502 shall be provided in accordance with Table 208.2 except as required by 208.2.1, 208.2.2, and 208.2.3. Where more than one parking facility is provided on a site, the number of accessible spaces provided on the site shall be calculated according to the number of spaces required for each parking facility. TABLE 208.2—PARKING SPACES Total number of parking spaces provided in parking facility 1 to 25 ....................... 26 to 50 ..................... 51 to 75 ..................... 76 to 100 ................... 101 to 150 ................. 151 to 200 ................. 201 to 300 ................. 301 to 400 ................. 401 to 500 ................. 501 to 1000 ............... E:\FR\FM\26SER2.SGM 26SER2 Minimum number of required accessible parking spaces 1 2 3 4 5 6 7 8 9 2 percent of total. Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations TABLE 208.2—PARKING SPACES— Continued Minimum number of required accessible parking spaces 1001 and over ........... emcdonald on DSK67QTVN1PROD with RULES2 Total number of parking spaces provided in parking facility 20, plus 1 for each 100, or fraction thereof, over 1000. 208.2.1 Hospital Outpatient Facilities. Ten percent of patient and visitor parking spaces provided to serve hospital outpatient facilities shall comply with 502. 208.2.2 Rehabilitation Facilities and Outpatient Physical Therapy Facilities. Twenty percent of patient and visitor parking spaces provided to serve rehabilitation facilities specializing in treating conditions that affect mobility and outpatient physical therapy facilities shall comply with 502. 208.2.3 Residential Facilities. Parking spaces provided to serve residential facilities shall comply with 208.2.3. 208.2.3.1 Parking for Residents. Where at least one parking space is provided for each residential dwelling unit, at least one parking space complying with 502 shall be provided for each residential dwelling unit required to provide mobility features complying with 809.2 through 809.4. 208.2.3.2 Additional Parking Spaces for Residents. Where the total number of parking spaces provided for each residential dwelling unit exceeds one parking space per residential dwelling unit, 2 percent, but no fewer than one space, of all the parking spaces not covered by 208.2.3.1 shall comply with 502. 208.2.3.3 Parking for Guests, Employees, and Other Non-Residents. Where parking spaces are provided for persons other than residents, parking shall be provided in accordance with Table 208.2. 208.2.4 Van Parking Spaces. For every six or fraction of six parking spaces required by 208.2 to comply with 502, at least one shall be a van parking space complying with 502. 208.3 Location. Parking facilities shall comply with 208.3. 208.3.1 General. Parking spaces complying with 502 that serve a particular building or facility shall be located on the shortest accessible route from parking to an entrance complying with 206.4. Where parking serves more than one accessible entrance, parking spaces complying with 502 shall be dispersed and located on the shortest accessible route to the accessible entrances. In parking facilities that do not serve a particular building or facility, parking spaces complying with 502 shall be located on the shortest accessible route to an accessible pedestrian entrance of the parking facility. EXCEPTIONS: 1. All van parking spaces shall be permitted to be grouped on one level within a multi-story parking facility. 2. Parking spaces shall be permitted to be located in different parking facilities if substantially equivalent or greater accessibility is provided in terms of distance from an accessible entrance or entrances, parking fee, and user convenience. 208.3.2 Residential Facilities. In residential facilities containing residential VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 dwelling units required to provide mobility features complying with 809.2 through 809.4, parking spaces provided in accordance with 208.2.3.1 shall be located on the shortest accessible route to the residential dwelling unit entrance they serve. Spaces provided in accordance with 208.2.3.2 shall be dispersed throughout all types of parking provided for the residential dwelling units. EXCEPTION: Parking spaces provided in accordance with 208.2.3.2 shall not be required to be dispersed throughout all types of parking if substantially equivalent or greater accessibility is provided in terms of distance from an accessible entrance, parking fee, and user convenience. 209 Passenger Loading Zones and Bus Stops 209.1 General. Passenger loading zones shall be provided in accordance with 209. 209.2 Type. Where provided, passenger loading zones shall comply with 209.2. 209.2.1 Passenger Loading Zones. Passenger loading zones, except those required to comply with 209.2.2 and 209.2.3, shall provide at least one passenger loading zone complying with 503 in every continuous 100 linear feet (30 m) of loading zone space, or fraction thereof. 209.2.2 Bus Loading Zones. In bus loading zones restricted to use by designated or specified public transportation vehicles, each bus bay, bus stop, or other area designated for lift or ramp deployment shall comply with 810.2. 209.2.3 On-Street Bus Stops. On-street bus stops shall comply with 810.2 to the maximum extent practicable. 209.3 Medical Care and Long-Term Care Facilities. At least one passenger loading zone complying with 503 shall be provided at an accessible entrance to licensed medical care and licensed long-term care facilities where the period of stay exceeds twenty-four hours. 209.4 Valet Parking. Parking facilities that provide valet parking services shall provide at least one passenger loading zone complying with 503. 209.5 Mechanical Access Parking Garages. Mechanical access parking garages shall provide at least one passenger loading zone complying with 503 at vehicle drop-off and vehicle pick-up areas. 210 Stairways 210.1 General. Interior and exterior stairs that are part of a means of egress shall comply with 504. EXCEPTIONS: 1. In detention and correctional facilities, stairs that are not located in public use areas shall not be required to comply with 504. 2. In alterations, stairs between levels that are connected by an accessible route shall not be required to comply with 504, except that handrails complying with 505 shall be provided when the stairs are altered. 3. In assembly areas, aisle stairs shall not be required to comply with 504. 4. Stairs that connect play components shall not be required to comply with 504. 211 Drinking Fountains 211.1 General. Where drinking fountains are provided on an exterior site, on a floor, PO 00000 Frm 00027 Fmt 4701 Sfmt 4700 59501 or within a secured area they shall be provided in accordance with 211. EXCEPTION: In detention or correctional facilities, drinking fountains only serving holding or housing cells not required to comply with 232 shall not be required to comply with 211. 211.2 Minimum Number. No fewer than two drinking fountains shall be provided. One drinking fountain shall comply with 602.1 through 602.6 and one drinking fountain shall comply with 602.7. EXCEPTION: Where a single drinking fountain complies with 602.1 through 602.6 and 602.7, it shall be permitted to be substituted for two separate drinking fountains. 211.3 More Than Minimum Number. Where more than the minimum number of drinking fountains specified in 211.2 are provided, 50 percent of the total number of drinking fountains provided shall comply with 602.1 through 602.6, and 50 percent of the total number of drinking fountains provided shall comply with 602.7. EXCEPTION: Where 50 percent of the drinking fountains yields a fraction, 50 percent shall be permitted to be rounded up or down provided that the total number of drinking fountains complying with 211 equals 100 percent of drinking fountains. 212 Kitchens, Kitchenettes, and Sinks 212.1 General. Where provided, kitchens, kitchenettes, and sinks shall comply with 212. 212.2 Kitchens and Kitchenettes. Kitchens and kitchenettes shall comply with 804. 212.3 Sinks. Where sinks are provided, at least 5 percent, but no fewer than one, of each type provided in each accessible room or space shall comply with 606. EXCEPTION: Mop or service sinks shall not be required to comply with 212.3. 213 Toilet Facilities and Bathing Facilities 213.1 General. Where toilet facilities and bathing facilities are provided, they shall comply with 213. Where toilet facilities and bathing facilities are provided in facilities permitted by 206.2.3 Exceptions 1 and 2 not to connect stories by an accessible route, toilet facilities and bathing facilities shall be provided on a story connected by an accessible route to an accessible entrance. 213.2 Toilet Rooms and Bathing Rooms. Where toilet rooms are provided, each toilet room shall comply with 603. Where bathing rooms are provided, each bathing room shall comply with 603. EXCEPTIONS: 1. In alterations where it is technically infeasible to comply with 603, altering existing toilet or bathing rooms shall not be required where a single unisex toilet room or bathing room complying with 213.2.1 is provided and located in the same area and on the same floor as existing inaccessible toilet or bathing rooms. 2. Where exceptions for alterations to qualified historic buildings or facilities are permitted by 202.5, no fewer than one toilet room for each sex complying with 603 or one unisex toilet room complying with 213.2.1 shall be provided. 3. Where multiple single user portable toilet or bathing units are clustered at a single E:\FR\FM\26SER2.SGM 26SER2 59502 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 location, no more than 5 percent of the toilet units and bathing units at each cluster shall be required to comply with 603. Portable toilet units and bathing units complying with 603 shall be identified by the International Symbol of Accessibility complying with 703.7.2.1. 4. Where multiple single user toilet rooms are clustered at a single location, no more than 50 percent of the single user toilet rooms for each use at each cluster shall be required to comply with 603. 213.2.1 Unisex (Single-Use or Family) Toilet and Unisex Bathing Rooms. Unisex toilet rooms shall contain not more than one lavatory, and two water closets without urinals or one water closet and one urinal. Unisex bathing rooms shall contain one shower or one shower and one bathtub, one lavatory, and one water closet. Doors to unisex toilet rooms and unisex bathing rooms shall have privacy latches. 213.3 Plumbing Fixtures and Accessories. Plumbing fixtures and accessories provided in a toilet room or bathing room required to comply with 213.2 shall comply with 213.3. 213.3.1 Toilet Compartments. Where toilet compartments are provided, at least one toilet compartment shall comply with 604.8.1. In addition to the compartment required to comply with 604.8.1, at least one compartment shall comply with 604.8.2 where six or more toilet compartments are provided, or where the combination of urinals and water closets totals six or more fixtures. 213.3.2 Water Closets. Where water closets are provided, at least one shall comply with 604. 213.3.3 Urinals. Where more than one urinal is provided, at least one shall comply with 605. 213.3.4 Lavatories. Where lavatories are provided, at least one shall comply with 606 and shall not be located in a toilet compartment. 213.3.5 Mirrors. Where mirrors are provided, at least one shall comply with 603.3. 213.3.6 Bathing Facilities. Where bathtubs or showers are provided, at least one bathtub complying with 607 or at least one shower complying with 608 shall be provided. 213.3.7 Coat Hooks and Shelves. Where coat hooks or shelves are provided in toilet rooms without toilet compartments, at least one of each type shall comply with 603.4. Where coat hooks or shelves are provided in toilet compartments, at least one of each type complying with 604.8.3 shall be provided in toilet compartments required to comply with 213.3.1. Where coat hooks or shelves are provided in bathing facilities, at least one of each type complying with 603.4 shall serve fixtures required to comply with 213.3.6. 214 Washing Machines and Clothes Dryers 214.1 General. Where provided, washing machines and clothes dryers shall comply with 214. 214.2 Washing Machines. Where three or fewer washing machines are provided, at least one shall comply with 611. Where more than three washing machines are provided, at least two shall comply with 611. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 214.3 Clothes Dryers. Where three or fewer clothes dryers are provided, at least one shall comply with 611. Where more than three clothes dryers are provided, at least two shall comply with 611. 215 Fire Alarm Systems 215.1 General. Where fire alarm systems provide audible alarm coverage, alarms shall comply with 215. EXCEPTION: In existing facilities, visible alarms shall not be required except where an existing fire alarm system is upgraded or replaced, or a new fire alarm system is installed. 215.2 Public and Common Use Areas. Alarms in public use areas and common use areas shall comply with 702. 215.3 Employee Work Areas. Where employee work areas have audible alarm coverage, the wiring system shall be designed so that visible alarms complying with 702 can be integrated into the alarm system. 215.4 Transient Lodging. Guest rooms required to comply with 224.4 shall provide alarms complying with 702. 215.5 Residential Facilities. Where provided in residential dwelling units required to comply with 809.5, alarms shall comply with 702. 216 Signs 216.1 General. Signs shall be provided in accordance with 216 and shall comply with 703. EXCEPTIONS: 1. Building directories, menus, seat and row designations in assembly areas, occupant names, building addresses, and company names and logos shall not be required to comply with 216. 2. In parking facilities, signs shall not be required to comply with 216.2, 216.3, and 216.6 through 216.12. 3. Temporary, 7 days or less, signs shall not be required to comply with 216. 4. In detention and correctional facilities, signs not located in public use areas shall not be required to comply with 216. 216.2 Designations. Interior and exterior signs identifying permanent rooms and spaces shall comply with 703.1, 703.2, and 703.5. Where pictograms are provided as designations of permanent interior rooms and spaces, the pictograms shall comply with 703.6 and shall have text descriptors complying with 703.2 and 703.5. EXCEPTION: Exterior signs that are not located at the door to the space they serve shall not be required to comply with 703.2. 216.3 Directional and Informational Signs. Signs that provide direction to or information about interior spaces and facilities of the site shall comply with 703.5. 216.4 Means of Egress. Signs for means of egress shall comply with 216.4. 216.4.1 Exit Doors. Doors at exit passageways, exit discharge, and exit stairways shall be identified by tactile signs complying with 703.1, 703.2, and 703.5. 216.4.2 Areas of Refuge. Signs required by section 1003.2.13.5.4 of the International Building Code (2000 edition) or section 1007.6.4 of the International Building Code (2003 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1) to provide instructions in areas of refuge shall comply with 703.5. PO 00000 Frm 00028 Fmt 4701 Sfmt 4700 216.4.3 Directional Signs. Signs required by section 1003.2.13.6 of the International Building Code (2000 edition) or section 1007.7 of the International Building Code (2003 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1) to provide directions to accessible means of egress shall comply with 703.5. 216.5 Parking. Parking spaces complying with 502 shall be identified by signs complying with 502.6. EXCEPTIONS: 1. Where a total of four or fewer parking spaces, including accessible parking spaces, are provided on a site, identification of accessible parking spaces shall not be required. 2. In residential facilities, where parking spaces are assigned to specific residential dwelling units, identification of accessible parking spaces shall not be required. 216.6 Entrances. Where not all entrances comply with 404, entrances complying with 404 shall be identified by the International Symbol of Accessibility complying with 703.7.2.1. Directional signs complying with 703.5 that indicate the location of the nearest entrance complying with 404 shall be provided at entrances that do not comply with 404. 216.7 Elevators. Where existing elevators do not comply with 407, elevators complying with 407 shall be clearly identified with the International Symbol of Accessibility complying with 703.7.2.1. 216.8 Toilet Rooms and Bathing Rooms. Where existing toilet rooms or bathing rooms do not comply with 603, directional signs indicating the location of the nearest toilet room or bathing room complying with 603 within the facility shall be provided. Signs shall comply with 703.5 and shall include the International Symbol of Accessibility complying with 703.7.2.1. Where existing toilet rooms or bathing rooms do not comply with 603, the toilet rooms or bathing rooms complying with 603 shall be identified by the International Symbol of Accessibility complying with 703.7.2.1. Where clustered single user toilet rooms or bathing facilities are permitted to use exceptions to 213.2, toilet rooms or bathing facilities complying with 603 shall be identified by the International Symbol of Accessibility complying with 703.7.2.1 unless all toilet rooms and bathing facilities comply with 603. 216.9 TTYs. Identification and directional signs for public TTYs shall be provided in accordance with 216.9. 216.9.1 Identification Signs. Public TTYs shall be identified by the International Symbol of TTY complying with 703.7.2.2. 216.9.2 Directional Signs. Directional signs indicating the location of the nearest public TTY shall be provided at all banks of public pay telephones not containing a public TTY. In addition, where signs provide direction to public pay telephones, they shall also provide direction to public TTYs. Directional signs shall comply with 703.5 and shall include the International Symbol of TTY complying with 703.7.2.2. 216.10 Assistive Listening Systems. Each assembly area required by 219 to provide assistive listening systems shall provide signs informing patrons of the availability of the E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations assistive listening system. Assistive listening signs shall comply with 703.5 and shall include the International Symbol of Access for Hearing Loss complying with 703.7.2.4. EXCEPTION: Where ticket offices or windows are provided, signs shall not be required at each assembly area provided that signs are displayed at each ticket office or window informing patrons of the availability of assistive listening systems. 216.11 Check-Out Aisles. Where more than one check-out aisle is provided, checkout aisles complying with 904.3 shall be identified by the International Symbol of Accessibility complying with 703.7.2.1. Where check-out aisles are identified by numbers, letters, or functions, signs identifying check-out aisles complying with 904.3 shall be located in the same location as the checkout aisle identification. EXCEPTION: Where all check-out aisles serving a single function comply with 904.3, signs complying with 703.7.2.1 shall not be required. 216.12 Amusement Rides. Signs identifying the type of access provided on amusement rides shall be provided at entries to queues and waiting lines. In addition, where accessible unload areas also serve as accessible load areas, signs indicating the location of the accessible load and unload areas shall be provided at entries to queues and waiting lines. 217 Telephones 217.1 General. Where coin-operated public pay telephones, coinless public pay telephones, public closed-circuit telephones, public courtesy phones, or other types of public telephones are provided, public telephones shall be provided in accordance with 217 for each type of public telephone provided. For purposes of this section, a bank of telephones shall be considered to be two or more adjacent telephones. 217.2 Wheelchair Accessible Telephones. Where public telephones are provided, wheelchair accessible telephones complying with 704.2 shall be provided in accordance with Table 217.2. EXCEPTION: Drive-up only public telephones shall not be required to comply with 217.2. TABLE 217.2—WHEELCHAIR ACCESSIBLE TELEPHONES Number of telephones provided on a floor, level, or exterior site Minimum number of required wheelchair accessible telephones 1 or more single units 1 per floor, level, and exterior site. 1 per floor, level, and exterior site. 1 per bank. 1 bank ....................... emcdonald on DSK67QTVN1PROD with RULES2 2 or more banks ........ 217.3 Volume Controls. All public telephones shall have volume controls complying with 704.3. 217.4 TTYs. TTYs complying with 704.4 shall be provided in accordance with 217.4. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 217.4.1 Bank Requirement. Where four or more public pay telephones are provided at a bank of telephones, at least one public TTY complying with 704.4 shall be provided at that bank. EXCEPTION: TTYs shall not be required at banks of telephones located within 200 feet (61 m) of, and on the same floor as, a bank containing a public TTY. 217.4.2 Floor Requirement. TTYs in public buildings shall be provided in accordance with 217.4.2.1. TTYs in private buildings shall be provided in accordance with 217.4.2.2. 217.4.2.1 Public Buildings. Where at least one public pay telephone is provided on a floor of a public building, at least one public TTY shall be provided on that floor. 217.4.2.2 Private Buildings. Where four or more public pay telephones are provided on a floor of a private building, at least one public TTY shall be provided on that floor. 217.4.3 Building Requirement. TTYs in public buildings shall be provided in accordance with 217.4.3.1. TTYs in private buildings shall be provided in accordance with 217.4.3.2. 217.4.3.1 Public Buildings. Where at least one public pay telephone is provided in a public building, at least one public TTY shall be provided in the building. Where at least one public pay telephone is provided in a public use area of a public building, at least one public TTY shall be provided in the public building in a public use area. 217.4.3.2 Private Buildings. Where four or more public pay telephones are provided in a private building, at least one public TTY shall be provided in the building. 217.4.4 Exterior Site Requirement. Where four or more public pay telephones are provided on an exterior site, at least one public TTY shall be provided on the site. 217.4.5 Rest Stops, Emergency Roadside Stops, and Service Plazas. Where at least one public pay telephone is provided at a public rest stop, emergency roadside stop, or service plaza, at least one public TTY shall be provided. 217.4.6 Hospitals. Where at least one public pay telephone is provided serving a hospital emergency room, hospital recovery room, or hospital waiting room, at least one public TTY shall be provided at each location. 217.4.7 Transportation Facilities. In transportation facilities, in addition to the requirements of 217.4.1 through 217.4.4, where at least one public pay telephone serves a particular entrance to a bus or rail facility, at least one public TTY shall be provided to serve that entrance. In airports, in addition to the requirements of 217.4.1 through 217.4.4, where four or more public pay telephones are located in a terminal outside the security areas, a concourse within the security areas, or a baggage claim area in a terminal, at least one public TTY shall be provided in each location. 217.4.8 Detention and Correctional Facilities. In detention and correctional facilities, where at least one pay telephone is provided in a secured area used only by PO 00000 Frm 00029 Fmt 4701 Sfmt 4700 59503 detainees or inmates and security personnel, at least one TTY shall be provided in at least one secured area. 217.5 Shelves for Portable TTYs. Where a bank of telephones in the interior of a building consists of three or more public pay telephones, at least one public pay telephone at the bank shall be provided with a shelf and an electrical outlet in accordance with 704.5. EXCEPTIONS: 1. Secured areas of detention and correctional facilities where shelves and outlets are prohibited for purposes of security or safety shall not be required to comply with 217.5. 2. The shelf and electrical outlet shall not be required at a bank of telephones with a TTY. 218 Transportation Facilities 218.1 General. Transportation facilities shall comply with 218. 218.2 New and Altered Fixed Guideway Stations. New and altered stations in rapid rail, light rail, commuter rail, intercity rail, high speed rail, and other fixed guideway systems shall comply with 810.5 through 810.10. 218.3 Key Stations and Existing Intercity Rail Stations. Key stations and existing intercity rail stations shall comply with 810.5 through 810.10. 218.4 Bus Shelters. Where provided, bus shelters shall comply with 810.3. 218.5 Other Transportation Facilities. In other transportation facilities, public address systems shall comply with 810.7 and clocks shall comply with 810.8. 219 Assistive Listening Systems 219.1 General. Assistive listening systems shall be provided in accordance with 219 and shall comply with 706. 219.2 Required Systems. In each assembly area where audible communication is integral to the use of the space, an assistive listening system shall be provided. EXCEPTION: Other than in courtrooms, assistive listening systems shall not be required where audio amplification is not provided. 219.3 Receivers. Receivers complying with 706.2 shall be provided for assistive listening systems in each assembly area in accordance with Table 219.3. Twenty-five percent minimum of receivers provided, but no fewer than two, shall be hearing-aid compatible in accordance with 706.3. EXCEPTIONS: 1. Where a building contains more than one assembly area and the assembly areas required to provide assistive listening systems are under one management, the total number of required receivers shall be permitted to be calculated according to the total number of seats in the assembly areas in the building provided that all receivers are usable with all systems. 2. Where all seats in an assembly area are served by an induction loop assistive listening system, the minimum number of receivers required by Table 219.3 to be hearing-aid compatible shall not be required to be provided. E:\FR\FM\26SER2.SGM 26SER2 59504 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations TABLE 219.3—RECEIVERS FOR ASSISTIVE LISTENING SYSTEMS Minimum number of required receivers required to be hearing-aid compatible Capacity of seating in assembly area Minimum number of required receivers 50 or less ........................................................... 51 to 200 ........................................................... 201 to 500 ......................................................... 501 to 1000 ....................................................... 1001 to 2000 ..................................................... 2001 and over ................................................... 2 ........................................................................ 2, plus 1 per 25 seats over 50 seats ............... 2, plus 1 per 25 seats over 50 seats 1 ............. 20, plus 1 per 33 seats over 500 seats 1 ......... 35, plus 1 per 50 seats over 1000 seats 1 ....... 55 plus 1 per 100 seats over 2000 seats 1 ...... 2. 2. 1 per 1 per 1 per 1 per be located in not less than 20 percent of all boxes provided. Wheelchair spaces shall comply with 802.1. 221.2.1.4 Team or Player Seating. At least one wheelchair space complying with 802.1 shall be provided in team or player seating areas serving areas of sport activity. EXCEPTION: Wheelchair spaces shall not be required in team or player seating areas serving bowling lanes not required to comply with 206.2.11. 221.2.2 Integration. Wheelchair spaces shall be an integral part of the seating plan. 221.2.3 Lines of Sight and Dispersion. Wheelchair spaces shall provide lines of sight complying with 802.2 and shall comply with 221.2.3. In providing lines of sight, wheelchair spaces shall be dispersed. Wheelchair spaces shall provide spectators with choices of seating locations and viewing angles that are substantially equivalent to, or better than, the choices of seating locations and viewing angles available to all other spectators. When the number of wheelchair spaces required by 221.2.1 has been met, further dispersion shall not be required. EXCEPTION: Wheelchair spaces in team or player seating areas serving areas of sport activity shall not be required to comply with 221.2.3. 221.2.3.1 Horizontal Dispersion. Wheelchair spaces shall be dispersed horizontally. EXCEPTIONS: 1. Horizontal dispersion shall not be required in assembly areas with 300 or fewer seats if the companion seats required by 221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length. Intermediate aisles shall be included in determining the total row length. If the row length in the 2nd and 3rd quartile of a row is insufficient to accommodate the required number of companion seats and wheelchair spaces, the additional companion seats and wheelchair spaces shall be permitted to be located in the 1st and 4th quartile of the row. 2. In row seating, two wheelchair spaces shall be permitted to be located side-by-side. 221.2.3.2 Vertical Dispersion. Wheelchair spaces shall be dispersed vertically at varying distances from the screen, performance area, or playing field. In addition, wheelchair spaces shall be located in each balcony or mezzanine that is located on an accessible route. EXCEPTIONS: 1. Vertical dispersion shall not be required in assembly areas with 300 or fewer seats if the wheelchair spaces provide viewing angles that are equivalent to, or better than, the average viewing angle provided in the facility. 2. In bleachers, wheelchair spaces shall not be required to be provided in rows other than rows at points of entry to bleacher seating. 221.3 Companion Seats. At least one companion seat complying with 802.3 shall be provided for each wheelchair space required by 221.2.1. 221.4 Designated Aisle Seats. At least 5 percent of the total number of aisle seats provided shall comply with 802.4 and shall be the aisle seats located closest to accessible routes. EXCEPTION: Team or player seating areas serving areas of sport activity shall not be required to comply with 221.4. 221.5 Lawn Seating. Lawn seating areas and exterior overflow seating areas, where fixed seats are not provided, shall connect to an accessible route. 1 Or receivers.1 receivers.1 receivers.1 receivers.1 fraction thereof. 220 Automatic Teller Machines and Fare Machines 220.1 General. Where automatic teller machines or self-service fare vending, collection, or adjustment machines are provided, at least one of each type provided at each location shall comply with 707. Where bins are provided for envelopes, waste paper, or other purposes, at least one of each type shall comply with 811. 221 Assembly Areas 221.1 General. Assembly areas shall provide wheelchair spaces, companion seats, and designated aisle seats complying with 221 and 802. In addition, lawn seating shall comply with 221.5. 221.2 Wheelchair Spaces. Wheelchair spaces complying with 221.2 shall be provided in assembly areas with fixed seating. 221.2.1 Number and Location. Wheelchair spaces shall be provided complying with 221.2.1. 221.2.1.1 General Seating. Wheelchair spaces complying with 802.1 shall be provided in accordance with Table 221.2.1.1. TABLE 221.2.1.1—NUMBER OF WHEELCHAIR SPACES IN ASSEMBLY AREAS Number of seats 4 to 25 ....................... 26 to 50 ..................... 51 to 150 ................... 151 to 300 ................. 301 to 500 ................. 501 to 5000 ............... 5001 and over ........... emcdonald on DSK67QTVN1PROD with RULES2 4 4 4 4 Minimum number of required wheelchair spaces 1. 2. 4. 5. 6. 6, plus 1 for each 150, or fraction thereof, between 501 through 5000. 36, plus 1 for each 200, or fraction thereof, over 5000. 221.2.1.2 Luxury Boxes, Club Boxes, and Suites in Arenas, Stadiums, and Grandstands. In each luxury box, club box, and suite within arenas, stadiums, and grandstands, wheelchair spaces complying with 802.1 shall be provided in accordance with Table 221.2.1.1. 221.2.1.3 Other Boxes. In boxes other than those required to comply with 221.2.1.2, the total number of wheelchair spaces required shall be determined in accordance with Table 221.2.1.1. Wheelchair spaces shall VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 PO 00000 Frm 00030 Fmt 4701 Sfmt 4700 222 Dressing, Fitting, and Locker Rooms 222.1 General. Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with 803. EXCEPTION: In alterations, where it is technically infeasible to provide rooms in accordance with 222.1, one room for each sex on each level shall comply with 803. Where only unisex rooms are provided, unisex rooms shall be permitted. 222.2 Coat Hooks and Shelves. Where coat hooks or shelves are provided in dressing, fitting or locker rooms without individual compartments, at least one of each type shall comply with 803.5. Where coat hooks or shelves are provided in individual compartments at least one of each type complying with 803.5 shall be provided in individual compartments in dressing, fitting, or locker rooms required to comply with 222.1. 223 Medical Care and Long-Term Care Facilities 223.1 General. In licensed medical care facilities and licensed long-term care facilities where the period of stay exceeds twenty four hours, patient or resident sleeping rooms shall be provided in accordance with 223. EXCEPTION: Toilet rooms that are part of critical or intensive care patient sleeping rooms shall not be required to comply with 603. 223.1.1 Alterations. Where sleeping rooms are altered or added, the requirements of 223 shall apply only to the sleeping rooms being altered or added until the number of sleeping rooms complies with the minimum number required for new construction. E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 223.2 Hospitals, Rehabilitation Facilities, Psychiatric Facilities and Detoxification Facilities. Hospitals, rehabilitation facilities, psychiatric facilities and detoxification facilities shall comply with 223.2. 223.2.1 Facilities Not Specializing in Treating Conditions That Affect Mobility. In facilities not specializing in treating conditions that affect mobility, at least 10 percent, but no fewer than one, of the patient sleeping rooms shall provide mobility features complying with 805. 223.2.2 Facilities Specializing in Treating Conditions That Affect Mobility. In facilities specializing in treating conditions that affect mobility, 100 percent of the patient sleeping rooms shall provide mobility features complying with 805. 223.3 Long-Term Care Facilities. In licensed long-term care facilities, at least 50 percent, but no fewer than one, of each type of resident sleeping room shall provide mobility features complying with 805. 224 Transient Lodging Guest Rooms 224.1 General. Transient lodging facilities shall provide guest rooms in accordance with 224. 224.1.1 Alterations. Where guest rooms are altered or added, the requirements of 224 shall apply only to the guest rooms being altered or added until the number of guest 59505 rooms complies with the minimum number required for new construction. 224.1.2 Guest Room Doors and Doorways. Entrances, doors, and doorways providing user passage into and within guest rooms that are not required to provide mobility features complying with 806.2 shall comply with 404.2.3. EXCEPTION: Shower and sauna doors in guest rooms that are not required to provide mobility features complying with 806.2 shall not be required to comply with 404.2.3. 224.2 Guest Rooms with Mobility Features. In transient lodging facilities, guest rooms with mobility features complying with 806.2 shall be provided in accordance with Table 224.2. TABLE 224.2—GUEST ROOMS WITH MOBILITY FEATURES Total number of guest rooms provided Minimum number of required rooms without roll-in showers Minimum number of required rooms with roll-in showers Total number of required rooms 1 to 25 ............................................ 26 to 50 .......................................... 51 to 75 .......................................... 76 to 100 ........................................ 101 to 150 ...................................... 151 to 200 ...................................... 201 to 300 ...................................... 301 to 400 ...................................... 401 to 500 ...................................... 501 to 1000 .................................... 1001 and over ................................ 1 .................................................... 2 .................................................... 3 .................................................... 4 .................................................... 5 .................................................... 6 .................................................... 7 .................................................... 8 .................................................... 9 .................................................... 2 percent of total .......................... 20, plus 1 for each 100, or fraction thereof, over 1000. 0 .................................................... 0 .................................................... 1 .................................................... 1 .................................................... 2 .................................................... 2 .................................................... 3 .................................................... 4 .................................................... 4 .................................................... 1 percent of total .......................... 10, plus 1 for each 100, or fraction thereof, over 1000. 1. 2. 4. 5. 7. 8. 10. 12. 13. 3 percent of total. 30, plus 2 for each 100, or fraction thereof, over 1000. 224.3 Beds. In guest rooms having more than 25 beds, 5 percent minimum of the beds shall have clear floor space complying with 806.2.3. 224.4 Guest Rooms with Communication Features. In transient lodging facilities, guest rooms with communication features complying with 806.3 shall be provided in accordance with Table 224.4. TABLE 224.4—GUEST ROOMS WITH COMMUNICATION FEATURES Minimum number of required guest rooms with communication features 2 to 25 ................... 26 to 50 ................. 51 to 75 ................. 76 to 100 ............... 101 to 150 ............. 151 to 200 ............. 201 to 300 ............. 301 to 400 ............. 401 to 500 ............. 501 to 1000 ........... 1001 and over ....... emcdonald on DSK67QTVN1PROD with RULES2 Total number of guest rooms provided 2. 4. 7. 9. 12. 14. 17. 20. 22. 5 percent of total. 50, plus 3 for each 100 over 1000. 224.5 Dispersion. Guest rooms required to provide mobility features complying with 806.2 and guest rooms required to provide communication features complying with 806.3 shall be dispersed among the various classes of guest rooms, and shall provide choices of types of guest rooms, number of VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 beds, and other amenities comparable to the choices provided to other guests. Where the minimum number of guest rooms required to comply with 806 is not sufficient to allow for complete dispersion, guest rooms shall be dispersed in the following priority: guest room type, number of beds, and amenities. At least one guest room required to provide mobility features complying with 806.2 shall also provide communication features complying with 806.3. Not more than 10 percent of guest rooms required to provide mobility features complying with 806.2 shall be used to satisfy the minimum number of guest rooms required to provide communication features complying with 806.3. 225 Storage 225.1 General. Storage facilities shall comply with 225. 225.2 Storage. Where storage is provided in accessible spaces, at least one of each type shall comply with 811. 225.2.1 Lockers. Where lockers are provided, at least 5 percent, but no fewer than one of each type, shall comply with 811. 225.2.2 Self-Service Shelving. Selfservice shelves shall be located on an accessible route complying with 402. Selfservice shelving shall not be required to comply with 308. 225.3 Self-Service Storage Facilities. Selfservice storage facilities shall provide individual self-service storage spaces complying with these requirements in accordance with Table 225.3. PO 00000 Frm 00031 Fmt 4701 Sfmt 4700 TABLE 225.3—SELF-SERVICE STORAGE FACILITIES Total spaces in facility 1 to 200 ..................... 201 and over ............. Minimum number of spaces required to be accessible 5 percent, but no fewer than 1. 10, plus 2 percent of total number of units over 200. 225.3.1 Dispersion. Individual selfservice storage spaces shall be dispersed throughout the various classes of spaces provided. Where more classes of spaces are provided than the number required to be accessible, the number of spaces shall not be required to exceed that required by Table 225.3. Self-service storage spaces complying with Table 225.3 shall not be required to be dispersed among buildings in a multibuilding facility. 226 Dining Surfaces and Work Surfaces 226.1 General. Where dining surfaces are provided for the consumption of food or drink, at least 5 percent of the seating spaces and standing spaces at the dining surfaces shall comply with 902. In addition, where work surfaces are provided for use by other than employees, at least 5 percent shall comply with 902. EXCEPTIONS: 1. Sales counters and service counters shall not be required to comply with 902. E:\FR\FM\26SER2.SGM 26SER2 59506 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 2. Check writing surfaces provided at check-out aisles not required to comply with 904.3 shall not be required to comply with 902. 226.2 Dispersion. Dining surfaces and work surfaces required to comply with 902 shall be dispersed throughout the space or facility containing dining surfaces and work surfaces. 227 Sales and Service 227.1 General. Where provided, checkout aisles, sales counters, service counters, food service lines, queues, and waiting lines shall comply with 227 and 904. 227.2 Check-Out Aisles. Where check-out aisles are provided, check-out aisles complying with 904.3 shall be provided in accordance with Table 227.2. Where checkout aisles serve different functions, check-out aisles complying with 904.3 shall be provided in accordance with Table 227.2 for each function. Where check-out aisles are dispersed throughout the building or facility, check-out aisles complying with 904.3 shall be dispersed. EXCEPTION: Where the selling space is under 5000 square feet (465 m2) no more than one check-out aisle complying with 904.3 shall be required. TABLE 227.2—CHECK-OUT AISLES Number of check-out aisles of each function Minimum number of check-out aisles of each function required to comply with 904.3 1 to 4 ......................... 5 to 8 ......................... 9 to 15 ....................... 16 and over ............... 1. 2. 3. 3, plus 20 percent of additional aisles. emcdonald on DSK67QTVN1PROD with RULES2 227.2.1 Altered Check-Out Aisles. Where check-out aisles are altered, at least one of each check-out aisle serving each function shall comply with 904.3 until the number of check-out aisles complies with 227.2. 227.3 Counters. Where provided, at least one of each type of sales counter and service counter shall comply with 904.4. Where counters are dispersed throughout the building or facility, counters complying with 904.4 also shall be dispersed. 227.4 Food Service Lines. Food service lines shall comply with 904.5. Where selfservice shelves are provided, at least 50 percent, but no fewer than one, of each type provided shall comply with 308. 227.5 Queues and Waiting Lines. Queues and waiting lines servicing counters or check-out aisles required to comply with 904.3 or 904.4 shall comply with 403. 228 Depositories, Vending Machines, Change Machines, Mail Boxes, and Fuel Dispensers 228.1 General. Where provided, at least one of each type of depository, vending machine, change machine, and fuel dispenser shall comply with 309. EXCEPTION: Drive-up only depositories shall not be required to comply with 309. 228.2 Mail Boxes. Where mail boxes are provided in an interior location, at least 5 VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 percent, but no fewer than one, of each type shall comply with 309. In residential facilities, where mail boxes are provided for each residential dwelling unit, mail boxes complying with 309 shall be provided for each residential dwelling unit required to provide mobility features complying with 809.2 through 809.4. 229 Windows 229.1 General. Where glazed openings are provided in accessible rooms or spaces for operation by occupants, at least one opening shall comply with 309. Each glazed opening required by an administrative authority to be operable shall comply with 309. EXCEPTIONS: 1. Glazed openings in residential dwelling units required to comply with 809 shall not be required to comply with 229. 2. Glazed openings in guest rooms required to provide communication features and in guest rooms required to comply with 206.5.3 shall not be required to comply with 229. 230 Two-Way Communication Systems 230.1 General. Where a two-way communication system is provided to gain admittance to a building or facility or to restricted areas within a building or facility, the system shall comply with 708. 231 Judicial Facilities 231.1 General. Judicial facilities shall comply with 231. 231.2 Courtrooms. Each courtroom shall comply with 808. 231.3 Holding Cells. Where provided, central holding cells and court-floor holding cells shall comply with 231.3. 231.3.1 Central Holding Cells. Where separate central holding cells are provided for adult male, juvenile male, adult female, or juvenile female, one of each type shall comply with 807.2. Where central holding cells are provided and are not separated by age or sex, at least one cell complying with 807.2 shall be provided. 231.3.2 Court-Floor Holding Cells. Where separate court-floor holding cells are provided for adult male, juvenile male, adult female, or juvenile female, each courtroom shall be served by one cell of each type complying with 807.2. Where court-floor holding cells are provided and are not separated by age or sex, courtrooms shall be served by at least one cell complying with 807.2. Cells may serve more than one courtroom. 231.4 Visiting Areas. Visiting areas shall comply with 231.4. 231.4.1 Cubicles and Counters. At least 5 percent, but no fewer than one, of cubicles shall comply with 902 on both the visitor and detainee sides. Where counters are provided, at least one shall comply with 904.4.2 on both the visitor and detainee sides. EXCEPTION: The detainee side of cubicles or counters at non-contact visiting areas not serving holding cells required to comply with 231 shall not be required to comply with 902 or 904.4.2. 231.4.2 Partitions. Where solid partitions or security glazing separate visitors from detainees at least one of each type of cubicle or counter partition shall comply with 904.6. PO 00000 Frm 00032 Fmt 4701 Sfmt 4700 232 Detention Facilities and Correctional Facilities 232.1 General. Buildings, facilities, or portions thereof, in which people are detained for penal or correction purposes, or in which the liberty of the inmates is restricted for security reasons shall comply with 232. 232.2 General Holding Cells and General Housing Cells. General holding cells and general housing cells shall be provided in accordance with 232.2. EXCEPTION: Alterations to cells shall not be required to comply except to the extent determined by the Attorney General. 232.2.1 Cells with Mobility Features. At least 2 percent, but no fewer than one, of the total number of cells in a facility shall provide mobility features complying with 807.2. 232.2.1.1 Beds. In cells having more than 25 beds, at least 5 percent of the beds shall have clear floor space complying with 807.2.3. 232.2.2 Cells with Communication Features. At least 2 percent, but no fewer than one, of the total number of general holding cells and general housing cells equipped with audible emergency alarm systems and permanently installed telephones within the cell shall provide communication features complying with 807.3. 232.3 Special Holding Cells and Special Housing Cells. Where special holding cells or special housing cells are provided, at least one cell serving each purpose shall provide mobility features complying with 807.2. Cells subject to this requirement include, but are not limited to, those used for purposes of orientation, protective custody, administrative or disciplinary detention or segregation, detoxification, and medical isolation. EXCEPTION: Alterations to cells shall not be required to comply except to the extent determined by the Attorney General. 232.4 Medical Care Facilities. Patient bedrooms or cells required to comply with 223 shall be provided in addition to any medical isolation cells required to comply with 232.3. 232.5 Visiting Areas. Visiting areas shall comply with 232.5. 232.5.1 Cubicles and Counters. At least 5 percent, but no fewer than one, of cubicles shall comply with 902 on both the visitor and detainee sides. Where counters are provided, at least one shall comply with 904.4.2 on both the visitor and detainee or inmate sides. EXCEPTION: The inmate or detainee side of cubicles or counters at non-contact visiting areas not serving holding cells or housing cells required to comply with 232 shall not be required to comply with 902 or 904.4.2. 232.5.2 Partitions. Where solid partitions or security glazing separate visitors from detainees or inmates at least one of each type of cubicle or counter partition shall comply with 904.6. 233 Residential Facilities 233.1 General. Facilities with residential dwelling units shall comply with 233. 233.2 Residential Dwelling Units Provided by Entities Subject to HUD Section E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 504 Regulations. Where facilities with residential dwelling units are provided by entities subject to regulations issued by the Department of Housing and Urban Development (residential dwelling units with mobility features complying with 809.2 through 809.4 in a number required by the applicable HUD regulations. Residential dwelling units required to provide mobility features complying with 809.2 through 809.4 shall be on an accessible route as required by 206. In addition, such entities shall provide residential dwelling units with communication features complying with 809.5 in a number required by the applicable HUD regulations. Entities subject to 233.2 shall not be required to comply with 233.3. 233.3 Residential Dwelling Units Provided by Entities Not Subject to HUD Section 504 Regulations. Facilities with residential dwelling units provided by entities not subject to regulations issued by the Department of Housing and Urban Development (HUD) under Section 504 of the Rehabilitation Act of 1973, as amended, shall comply with 233.3. 233.3.1 Minimum Number: New Construction. Newly constructed facilities with residential dwelling units shall comply with 233.3.1. EXCEPTION: Where facilities contain 15 or fewer residential dwelling units, the requirements of 233.3.1.1 and 233.3.1.2 shall apply to the total number of residential dwelling units that are constructed under a single contract, or are developed as a whole, whether or not located on a common site. 233.3.1.1 Residential Dwelling Units with Mobility Features. In facilities with residential dwelling units, at least 5 percent, but no fewer than one unit, of the total number of residential dwelling units shall provide mobility features complying with 809.2 through 809.4 and shall be on an accessible route as required by 206. 233.3.1.2 Residential Dwelling Units with Communication Features. In facilities with residential dwelling units, at least 2 percent, but no fewer than one unit, of the total number of residential dwelling units shall provide communication features complying with 809.5. 233.3.2 Residential Dwelling Units for Sale. Residential dwelling units offered for sale shall provide accessible features to the extent required by regulations issued by Federal agencies under the Americans with Disabilities Act or Section 504 of the Rehabilitation Act of 1973, as amended. 233.3.3 Additions. Where an addition to an existing building results in an increase in the number of residential dwelling units, the requirements of 233.3.1 shall apply only to the residential dwelling units that are added until the total number of residential dwelling units complies with the minimum number required by 233.3.1. Residential dwelling units required to comply with 233.3.1.1 shall be on an accessible route as required by 206. 233.3.4 Alterations. Alterations shall comply with 233.3.4. EXCEPTION: Where compliance with 809.2, 809.3, or 809.4 is technically infeasible, or where it is technically infeasible to provide an accessible route to a residential dwelling unit, the entity shall be VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 59507 permitted to alter or construct a comparable residential dwelling unit to comply with 809.2 through 809.4 provided that the minimum number of residential dwelling units required by 233.3.1.1 and 233.3.1.2, as applicable, is satisfied. 233.3.4.1 Alterations to Vacated Buildings. Where a building is vacated for the purposes of alteration, and the altered building contains more than 15 residential dwelling units, at least 5 percent of the residential dwelling units shall comply with 809.2 through 809.4 and shall be on an accessible route as required by 206. In addition, at least 2 percent of the residential dwelling units shall comply with 809.5. 233.3.4.2 Alterations to Individual Residential Dwelling Units. In individual residential dwelling units, where a bathroom or a kitchen is substantially altered, and at least one other room is altered, the requirements of 233.3.1 shall apply to the altered residential dwelling units until the total number of residential dwelling units complies with the minimum number required by 233.3.1.1 and 233.3.1.2. Residential dwelling units required to comply with 233.3.1.1 shall be on an accessible route as required by 206. EXCEPTION: Where facilities contain 15 or fewer residential dwelling units, the requirements of 233.3.1.1 and 233.3.1.2 shall apply to the total number of residential dwelling units that are altered under a single contract, or are developed as a whole, whether or not located on a common site. 233.3.5 Dispersion. Residential dwelling units required to provide mobility features complying with 809.2 through 809.4 and residential dwelling units required to provide communication features complying with 809.5 shall be dispersed among the various types of residential dwelling units in the facility and shall provide choices of residential dwelling units comparable to, and integrated with, those available to other residents. EXCEPTION: Where multi-story residential dwelling units are one of the types of residential dwelling units provided, onestory residential dwelling units shall be permitted as a substitute for multi-story residential dwelling units where equivalent spaces and amenities are provided in the one-story residential dwelling unit. off the ride by an adult, shall not be required to comply with 234.3. 3. Amusement rides that do not provide amusement ride seats shall not be required to comply with 234.3. 234.4 Existing Amusement Rides. Where existing amusement rides are altered, the alteration shall comply with 234.4. 234.4.1 Load and Unload Areas. Where load and unload areas serving existing amusement rides are newly designed and constructed, the load and unload areas shall comply with 1002.3. 234.4.2 Minimum Number. Where the structural or operational characteristics of an amusement ride are altered to the extent that the amusement ride’s performance differs from that specified by the manufacturer or the original design, the amusement ride shall comply with 234.3. 234 Amusement Rides 234.1 General. Amusement rides shall comply with 234. EXCEPTION: Mobile or portable amusement rides shall not be required to comply with 234. 234.2 Load and Unload Areas. Load and unload areas serving amusement rides shall comply with 1002.3. 234.3 Minimum Number. Amusement rides shall provide at least one wheelchair space complying with 1002.4, or at least one amusement ride seat designed for transfer complying with 1002.5, or at least one transfer device complying with 1002.6. EXCEPTIONS: 1. Amusement rides that are controlled or operated by the rider shall not be required to comply with 234.3. 2. Amusement rides designed primarily for children, where children are assisted on and 235.2.1 Dispersion. Boat slips complying with 1003.3.1 shall be dispersed throughout the various types of boat slips provided. Where the minimum number of boat slips required to comply with 1003.3.1 has been met, no further dispersion shall be required. 235.3 Boarding Piers at Boat Launch Ramps. Where boarding piers are provided at boat launch ramps, at least 5 percent, but no fewer than one, of the boarding piers shall comply with 1003.3.2. PO 00000 Frm 00033 Fmt 4701 Sfmt 4700 235 Recreational Boating Facilities 235.1 General. Recreational boating facilities shall comply with 235. 235.2 Boat Slips. Boat slips complying with 1003.3.1 shall be provided in accordance with Table 235.2. Where the number of boat slips is not identified, each 40 feet (12 m) of boat slip edge provided along the perimeter of the pier shall be counted as one boat slip for the purpose of this section. TABLE 235.2—BOAT SLIPS Total number of boat slips provided in facility 1 to 25 ........... 26 to 50 ......... 51 to 100 ....... 101 to 150 ..... 151 to 300 ..... 301 to 400 ..... 401 to 500 ..... 501 to 600 ..... 601 to 700 ..... 701 to 800 ..... 801 to 900 ..... 901 to 1000 ... 1001 and over 236 Minimum number of required accessible boat slips 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 12, plus 1 for every 100, or fraction thereof, over 1000. Exercise Machines and Equipment 236.1 General. At least one of each type of exercise machine and equipment shall comply with 1004. 237 Fishing Piers and Platforms 237.1 General. Fishing piers and platforms shall comply with 1005. E:\FR\FM\26SER2.SGM 26SER2 59508 238 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations Golf Facilities 238.1 General. Golf facilities shall comply with 238. 238.2 Golf Courses. Golf courses shall comply with 238.2. 238.2.1 Teeing Grounds. Where one teeing ground is provided for a hole, the teeing ground shall be designed and constructed so that a golf car can enter and exit the teeing ground. Where two teeing grounds are provided for a hole, the forward teeing ground shall be designed and constructed so that a golf car can enter and exit the teeing ground. Where three or more teeing grounds are provided for a hole, at least two teeing grounds, including the forward teeing ground, shall be designed and constructed so that a golf car can enter and exit each teeing ground. EXCEPTION: In existing golf courses, the forward teeing ground shall not be required to be one of the teeing grounds on a hole designed and constructed so that a golf car can enter and exit the teeing ground where compliance is not feasible due to terrain. 238.2.2 Putting Greens. Putting greens shall be designed and constructed so that a golf car can enter and exit the putting green. 238.2.3 Weather Shelters. Where provided, weather shelters shall be designed and constructed so that a golf car can enter and exit the weather shelter and shall comply with 1006.4. 238.3 Practice Putting Greens, Practice Teeing Grounds, and Teeing Stations at Driving Ranges. At least 5 percent, but no fewer than one, of practice putting greens, practice teeing grounds, and teeing stations at driving ranges shall be designed and constructed so that a golf car can enter and exit the practice putting greens, practice teeing grounds, and teeing stations at driving ranges. 239 Miniature Golf Facilities 239.1 General. Miniature golf facilities shall comply with 239. 239.2 Minimum Number. At least 50 percent of holes on miniature golf courses shall comply with 1007.3. 239.3 Miniature Golf Course Configuration. Miniature golf courses shall be configured so that the holes complying with 1007.3 are consecutive. Miniature golf courses shall provide an accessible route from the last hole complying with 1007.3 to the course entrance or exit without requiring travel through any other holes on the course. EXCEPTION: One break in the sequence of consecutive holes shall be permitted provided that the last hole on the miniature golf course is the last hole in the sequence. 240 Play Areas 240.1 General. Play areas for children ages 2 and over shall comply with 240. Where separate play areas are provided within a site for specific age groups, each play area shall comply with 240. EXCEPTIONS: 1. Play areas located in family child care facilities where the proprietor actually resides shall not be required to comply with 240. 2. In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the play area shall not be required to comply with 240. 3. Amusement attractions shall not be required to comply with 240. 4. Where play components are altered and the ground surface is not altered, the ground surface shall not be required to comply with 1008.2.6 unless required by 202.4. 240.1.1 Additions. Where play areas are designed and constructed in phases, the requirements of 240 shall apply to each successive addition so that when the addition is completed, the entire play area complies with all the applicable requirements of 240. 240.2 Play Components. Where provided, play components shall comply with 240.2. 240.2.1 Ground Level Play Components. Ground level play components shall be provided in the number and types required by 240.2.1. Ground level play components that are provided to comply with 240.2.1.1 shall be permitted to satisfy the additional number required by 240.2.1.2 if the minimum required types of play components are satisfied. Where two or more required ground level play components are provided, they shall be dispersed throughout the play area and integrated with other play components. 240.2.1.1 Minimum Number and Types. Where ground level play components are provided, at least one of each type shall be on an accessible route and shall comply with 1008.4. 240.2.1.2 Additional Number and Types. Where elevated play components are provided, ground level play components shall be provided in accordance with Table 240.2.1.2 and shall comply with 1008.4. EXCEPTION: If at least 50 percent of the elevated play components are connected by a ramp and at least 3 of the elevated play components connected by the ramp are different types of play components, the play area shall not be required to comply with 240.2.1.2. TABLE 240.2.1.2—NUMBER AND TYPES OF GROUND LEVEL PLAY COMPONENTS REQUIRED TO BE ON ACCESSIBLE ROUTES Minimum number of ground level play components required to be on an accessible route 1 ......................................................................... 2 to 4 .................................................................. 5 to 7 .................................................................. 8 to 10 ................................................................ 11 to 13 .............................................................. 14 to 16 .............................................................. 17 to 19 .............................................................. 20 to 22 .............................................................. 23 to 25 .............................................................. 26 and over ........................................................ emcdonald on DSK67QTVN1PROD with RULES2 Number of elevated play components provided Not applicable .................................................. 1 ....................................................................... 2 ....................................................................... 3 ....................................................................... 4 ....................................................................... 5 ....................................................................... 6 ....................................................................... 7 ....................................................................... 8 ....................................................................... 8, plus 1 for each additional 3, or fraction thereof, over 25. Not applicable. 1. 2. 3. 3. 3. 3. 4. 4. 5. 240.2.2 Elevated Play Components. Where elevated play components are provided, at least 50 percent shall be on an accessible route and shall comply with 1008.4. in each cluster shall be required to comply with 612. transfer systems complying with 1009.5; and pool stairs complying with 1009.6. At least one accessible means of entry provided shall comply with 1009.2 or 1009.3. EXCEPTIONS: 1. Where a swimming pool has less than 300 linear feet (91 m) of swimming pool wall, no more than one accessible means of entry shall be required provided that the accessible means of entry is a swimming pool lift complying with 1009.2 or sloped entry complying with 1009.3. 241 Saunas and Steam Rooms 241.1 General. Where provided, saunas and steam rooms shall comply with 612. EXCEPTION: Where saunas or steam rooms are clustered at a single location, no more than 5 percent of the saunas and steam rooms, but no fewer than one, of each type VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 242 Swimming Pools, Wading Pools, and Spas 242.1 General. Swimming pools, wading pools, and spas shall comply with 242. 242.2 Swimming Pools. At least two accessible means of entry shall be provided for swimming pools. Accessible means of entry shall be swimming pool lifts complying with 1009.2; sloped entries complying with 1009.3; transfer walls complying with 1009.4; PO 00000 Frm 00034 Fmt 4701 Sfmt 4700 Minimum number of different types of ground level play components required to be on an accessible route E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 2. Wave action pools, leisure rivers, sand bottom pools, and other pools where user access is limited to one area shall not be required to provide more than one accessible means of entry provided that the accessible means of entry is a swimming pool lift complying with 1009.2, a sloped entry complying with 1009.3, or a transfer system complying with 1009.5. 3. Catch pools shall not be required to provide an accessible means of entry provided that the catch pool edge is on an accessible route. 242.3 Wading Pools. At least one accessible means of entry shall be provided for wading pools. Accessible means of entry shall comply with sloped entries complying with 1009.3. 242.4 Spas. At least one accessible means of entry shall be provided for spas. Accessible means of entry shall comply with swimming pool lifts complying with 1009.2; transfer walls complying with 1009.4; or transfer systems complying with 1009.5. EXCEPTION: Where spas are provided in a cluster, no more than 5 percent, but no fewer than one, spa in each cluster shall be required to comply with 242.4. 243 Shooting Facilities With Firing Positions 243.1 General. Where shooting facilities with firing positions are designed and constructed at a site, at least 5 percent, but no fewer than one, of each type of firing position shall comply with 1010. 6. Revise Appendix C to this part to read as follows: ■ Appendix C to Part 1191— Architectural Barriers Act: Scoping ABA Chapter 1: Application and Administration emcdonald on DSK67QTVN1PROD with RULES2 F101 Purpose F101.1 General. This document contains scoping and technical requirements for accessibility to sites, facilities, buildings, and elements by individuals with disabilities. The requirements are to be applied during the design, construction, addition to, alteration, and lease of sites, facilities, buildings, and elements to the extent required by regulations issued by Federal agencies under the Architectural Barriers Act of 1968 (ABA). F102 Dimensions for Adults and Children F102.1 General. The technical requirements are based on adult dimensions and anthropometrics. In addition, this document includes technical requirements based on children’s dimensions and anthropometrics for drinking fountains, water closets, toilet compartments, lavatories and sinks, dining surfaces, and work surfaces. F103 Modifications and Waivers F103.1 General. The Architectural Barriers Act authorizes the Administrator of the General Services Administration, the Secretary of the Department of Housing and Urban Development, the Secretary of the Department of Defense, and the United States VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 Postal Service to modify or waive the accessibility standards for buildings and facilities covered by the Architectural Barriers Act on a case-by-case basis, upon application made by the head of the department, agency, or instrumentality of the United States concerned. The General Services Administration, the Department of Housing and Urban Development, the Department of Defense, and the United States Postal Service may grant a modification or waiver only upon a determination that it is clearly necessary. Section 502(b)(1) of the Rehabilitation Act of 1973 authorizes the Access Board to ensure that modifications and waivers are based on findings of fact and are not inconsistent with the Architectural Barriers Act. F104 Conventions F104.1 Dimensions. Dimensions that are not stated as ‘‘maximum’’ or ‘‘minimum’’ are absolute. F104.1.1 Construction and Manufacturing Tolerances. All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points. F104.2 Calculation of Percentages. Where the required number of elements or facilities to be provided is determined by calculations of ratios or percentages and remainders or fractions result, the next greater whole number of such elements or facilities shall be provided. Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted. F104.3 Figures. Unless specifically stated otherwise, figures are provided for informational purposes only. F105 Referenced Standards F105.1 General. The standards listed in F105.2 are incorporated by reference in this document and are part of the requirements to the prescribed extent of each such reference. The Director of the Federal Register has approved these standards for incorporation by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies of the referenced standards may be inspected at the Architectural and Transportation Barriers Compliance Board, 1331 F Street NW., Suite 1000, Washington, DC 20004; at the Department of Justice, Civil Rights Division, Disability Rights Section, 1425 New York Avenue NW., Washington, DC 20005; at the Department of Transportation, 1200 New Jersey Avenue SE., Washington, DC 20590; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741–6030, or go to https:// www.archives.gov/federal_register/code_of_ federal_regulations/ibr_locations.html. F105.2 Referenced Standards. The specific edition of the standards listed below are referenced in this document. Where differences occur between this document and the referenced standards, this document applies. F105.2.1 ANSI/BHMA. Copies of the referenced standards may be obtained from PO 00000 Frm 00035 Fmt 4701 Sfmt 4700 59509 the Builders Hardware Manufacturers Association, 355 Lexington Avenue, 15th floor, New York, NY 10017 (https:// www.buildershardware.com). ANSI/BHMA A156.10–1999 American National Standard for Power Operated Pedestrian Doors (see 404.3). ANSI/BHMA A156.19–1997 American National Standard for Power Assist and Low Energy Power Operated Doors (see 404.3, 408.3.2.1, and 409.3.1). ANSI/BHMA A156.19–2002 American National Standard for Power Assist and Low Energy Power Operated Doors (see 404.3, 408.3.2.1, and 409.3.1). F105.2.2 ASME. Copies of the referenced standards may be obtained from the American Society of Mechanical Engineers, Two Park Avenue, New York, New York 10016 (https://www.asme.org). ASME A17.1–2000 Safety Code for Elevators and Escalators, including ASME A17.1a–2002 Addenda and ASME A17.1b– 2003 Addenda (see 407.1, 408.1, 409.1, and 810.9). ASME A18.1–1999 Safety Standard for Platform Lifts and Stairway Chairlifts, including ASME A18.1a 2001 Addenda and ASME A18.1b–2001 Addenda (see 410.1). ASME A18.1–2003 Safety Standard for Platform Lifts and Stairway Chairlifts, (see 410.1). F105.2.3 ASTM. Copies of the referenced standards may be obtained from the American Society for Testing and Materials, 100 Bar Harbor Drive, West Conshohocken, Pennsylvania 19428 (https://www.astm.org). ASTM F1292–99 Standard Specification for Impact Attenuation of Surface Systems Under and Around Playground Equipment (see 1008.2.6.2). ASTM F1292–04 Standard Specification for Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment (see 1008.2.6.2). ASTM F1487–01 Standard Consumer Safety Performance Specification for Playground Equipment for Public Use (see F106.5). ASTM F1951–99 Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment (see 1008.2.6.1). F105.2.4 ICC/IBC. Copies of the referenced standard may be obtained from the International Code Council, 500 New Jersey Avenue NW., Washington, DC 20001 (www.iccsafe.org). International Building Code, 2000 Edition (see F207.1, F207.2, F216.4.2, F216.4.3, and 1005.2.1). International Building Code, 2001 Supplement (see F207.1 and F207.2). International Building Code, 2003 Edition (see F207.1, F207.2, F216.4.2, F216.4.3, and 1005.2.1). F105.2.5 NFPA. Copies of the referenced standards may be obtained from the National Fire Protection Association, 1 Batterymarch Park, Quincy, Massachusetts 02169 (https:// www.nfpa.org). NFPA 72 National Fire Alarm Code, 1999 Edition (see 702.1 and 809.5.2). NFPA 72 National Fire Alarm Code, 2002 Edition (see 702.1 and 809.5.2). E:\FR\FM\26SER2.SGM 26SER2 59510 emcdonald on DSK67QTVN1PROD with RULES2 F106 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations Definitions F106.1 General. For the purpose of this document, the terms defined in F106.5 have the indicated meaning. F106.2 Terms Defined in Referenced Standard. Terms not defined in F106.5 or in regulations issued by the Administrator of the General Services Administration, the Secretary of Defense, the Secretary of Housing and Urban Development, or the United States Postal Service to implement the Architectural Barriers Act but specifically defined in a referenced standard, shall have the specified meaning from the referenced standard unless otherwise stated. F106.3 Undefined Terms. The meaning of terms not specifically defined in F106.5 or in regulations issued by the Administrator of the General Services Administration, the Secretary of Defense, the Secretary of Housing and Urban Development, or the United States Postal Service to implement the Architectural Barriers Act or in referenced standards shall be as defined by collegiate dictionaries in the sense that the context implies. F106.4 Interchangeability. Words, terms and phrases used in the singular include the plural and those used in the plural include the singular. F106.5 Defined Terms. Accessible. A site, building, facility, or portion thereof that complies with this part. Accessible Means of Egress. A continuous and unobstructed way of egress travel from any point in a building or facility that provides an accessible route to an area of refuge, a horizontal exit, or a public way. Addition. An expansion, extension, or increase in the gross floor area or height of a building or facility. Administrative Authority. A governmental agency that adopts or enforces regulations and guidelines for the design, construction, or alteration of buildings and facilities. Alteration. A change to a building or facility that affects or could affect the usability of the building or facility or portion thereof. Alterations include, but are not limited to, remodeling, renovation, rehabilitation, reconstruction, historic restoration, resurfacing of circulation paths or vehicular ways, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height partitions. Normal maintenance, reroofing, painting or wallpapering, or changes to mechanical and electrical systems are not alterations unless they affect the usability of the building or facility. Amusement Attraction. Any facility, or portion of a facility, located within an amusement park or theme park which provides amusement without the use of an amusement device. Amusement attractions include, but are not limited to, fun houses, barrels, and other attractions without seats. Amusement Ride. A system that moves persons through a fixed course within a defined area for the purpose of amusement. Amusement Ride Seat. A seat that is builtin or mechanically fastened to an amusement ride intended to be occupied by one or more passengers. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 Area of Sport Activity. That portion of a room or space where the play or practice of a sport occurs. Assembly Area. A building or facility, or portion thereof, used for the purpose of entertainment, worship, educational or civic gatherings, or similar purposes. For the purposes of these requirements, assembly areas include, but are not limited to, classrooms, lecture halls, courtrooms, public meeting rooms, public hearing rooms, legislative chambers, motion picture houses, auditoria, theaters, playhouses, dinner theaters, concert halls, centers for the performing arts, amphitheaters, arenas, stadiums, grandstands, or convention centers. Assistive Listening System (ALS). An amplification system utilizing transmitters, receivers, and coupling devices to bypass the acoustical space between a sound source and a listener by means of induction loop, radio frequency, infrared, or direct-wired equipment. Boarding Pier. A portion of a pier where a boat is temporarily secured for the purpose of embarking or disembarking. Boards. Boards include, but are not limited to, wood, plastic, metal, and composite products. Boat Launch Ramp. A sloped surface designed for launching and retrieving trailered boats and other water craft to and from a body of water. Boat Slip. That portion of a pier, main pier, finger pier, or float where a boat is moored for the purpose of berthing, embarking, or disembarking. Building. Any structure used or intended for supporting or sheltering any use or occupancy. Camp Shelter. A partially enclosed structure that provides campers and hikers cover from weather and that does not contain plumbing fixtures or kitchen appliances. Camp shelters are not transient lodging facilities or residential dwelling units. Camping Facility. A site, or portion of a site, developed for outdoor recreational purposes that contains camping units. Camping Unit. An outdoor space in a camping facility used for camping that contains outdoor constructed features, parking spaces for recreational vehicles or other vehicles, tent pads or tent platforms, or camp shelters. Catch Pool. A pool or designated section of a pool used as a terminus for water slide flumes. Characters. Letters, numbers, punctuation marks and typographic symbols. Children’s Use. Describes spaces and elements specifically designed for use primarily by people 12 years old and younger. Circulation Path. An exterior or interior way of passage provided for pedestrian travel, including but not limited to, walks, hallways, courtyards, elevators, platform lifts, ramps, stairways, and landings. Closed-Circuit Telephone. A telephone with a dedicated line such as a house phone, courtesy phone or phone that must be used to gain entry to a facility. Common Use. Interior or exterior circulation paths, rooms, spaces, or elements PO 00000 Frm 00036 Fmt 4701 Sfmt 4700 that are not for public use and are made available for the shared use of two or more people. Cross Slope. The slope that is perpendicular to the direction of travel (see running slope). Curb Ramp. A short ramp cutting through a curb or built up to it. Detectable Warning. A standardized surface feature built in or applied to walking surfaces or other elements to warn of hazards on a circulation path. Element. An architectural or mechanical component of a building, facility, space, or site. Elevated Play Component. A play component that is approached above or below grade and that is part of a composite play structure consisting of two or more play components attached or functionally linked to create an integrated unit providing more than one play activity. Employee Work Area. All or any portion of a space used only by employees and used only for work. Corridors, toilet rooms, kitchenettes and break rooms are not employee work areas. Entrance. Any access point to a building or portion of a building or facility used for the purpose of entering. An entrance includes the approach walk, the vertical access leading to the entrance platform, the entrance platform itself, vestibule if provided, the entry door or gate, and the hardware of the entry door or gate. Facility. All or any portion of buildings, structures, site improvements, elements, and pedestrian routes or vehicular ways located on a site. Gangway. A variable-sloped pedestrian walkway that links a fixed structure or land with a floating structure. Gangways that connect to vessels are not addressed by this document. Golf Car Passage. A continuous passage on which a motorized golf car can operate. Ground Level Play Component. A play component that is approached and exited at the ground level. Joint Use. Interior or exterior rooms, spaces, or elements that are common space available for use by all occupants of the building. Joint use does not include mechanical or custodial rooms, or areas occupied by other tenants. Lease. Any agreement which establishes the relationship of landlord and tenant. Mail Boxes. Receptacles for the receipt of documents, packages, or other deliverable matter. Mail boxes include, but are not limited to, post office boxes and receptacles provided by commercial mail-receiving agencies, apartment facilities, or schools. Marked Crossing. A crosswalk or other identified path intended for pedestrian use in crossing a vehicular way. Mezzanine. An intermediate level or levels between the floor and ceiling of any story with an aggregate floor area of not more than one-third of the area of the room or space in which the level or levels are located. Mezzanines have sufficient elevation that space for human occupancy can be provided on the floor below. Military Installation. A base, camp, post, station, yard, center, homeport facility for E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations any ship, or other activity or operation under the jurisdiction of the Department of Defense, including any leased facility. Military installation does not include any facility used primarily for civil works, rivers and harbors projects, or flood control projects. Multiple, contiguous, or collocated bases, camps, posts, stations, yards, centers, or home ports shall not be considered as constituting a single military installation. Occupant Load. The number of persons for which the means of egress of a building or portion of a building is designed. Operable Part. A component of an element used to insert or withdraw objects, or to activate, deactivate, or adjust the element. Outdoor Constructed Features. Picnic tables, fire rings, grills, fireplaces, wood stoves, trash and recycling receptacles, water hydrants, utility and sewage hookups, outdoor rinsing showers, benches, and viewing scopes provided at outdoor recreation facilities. Picnic Facility. A site, or portion of a site, developed for outdoor recreational purposes that contains picnic units. Picnic Unit. An outdoor space in a picnic facility used for picnicking that contains outdoor constructed features. Pictogram. A pictorial symbol that represents activities, facilities, or concepts. Play Area. A portion of a site containing play components designed and constructed for children. Play Component. An element intended to generate specific opportunities for play, socialization, or learning. Play components are manufactured or natural; and are standalone or part of a composite play structure. Public Entrance. An entrance that is not a service entrance or a restricted entrance. Public Use. Interior or exterior rooms, spaces, or elements that are made available to the public. Public use may be provided at a building or facility that is privately or publicly owned. Public Way. Any street, alley or other parcel of land open to the outside air leading to a public street, which has been deeded, dedicated or otherwise permanently appropriated to the public for public use, and which has a clear width and height of not less than 10 feet (3050 mm). Qualified Historic Building or Facility. A building or facility that is listed in or eligible for listing in the National Register of Historic Places, or designated as historic under an appropriate State or local law. Ramp. A walking surface that has a running slope steeper than 1:20. Residential Dwelling Unit. A unit intended to be used as a residence, that is primarily long-term in nature. Residential dwelling units do not include transient lodging, inpatient medical care, licensed long-term care, and detention or correctional facilities. Restricted Entrance. An entrance that is made available for common use on a controlled basis but not public use and that is not a service entrance. Running Slope. The slope that is parallel to the direction of travel (see cross slope). Self-Service Storage. Building or facility designed and used for the purpose of renting or leasing individual storage spaces to customers for the purpose of storing and VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 removing personal property on a self-service basis. Service Entrance. An entrance intended primarily for delivery of goods or services. Site. A parcel of land bounded by a property line or a designated portion of a public right-of-way. Soft Contained Play Structure. A play structure made up of one or more play components where the user enters a fully enclosed play environment that utilizes pliable materials, such as plastic, netting, or fabric. Space. A definable area, such as a room, toilet room, hall, assembly area, entrance, storage room, alcove, courtyard, or lobby. Story. That portion of a building or facility designed for human occupancy included between the upper surface of a floor and upper surface of the floor or roof next above. A story containing one or more mezzanines has more than one floor level. Structural Frame. The columns and the girders, beams, and trusses having direct connections to the columns and all other members that are essential to the stability of the building or facility as a whole. Tactile. An object that can be perceived using the sense of touch. Technically Infeasible. With respect to an alteration of a building or a facility, something that has little likelihood of being accomplished because existing structural conditions would require removing or altering a loadbearing member that is an essential part of the structural frame; or because other existing physical or site constraints prohibit modification or addition of elements, spaces, or features that are in full and strict compliance with the minimum requirements. Teeing Ground. In golf, the starting place for the hole to be played. Trail. A pedestrian route developed primarily for outdoor recreational purposes. A pedestrian route developed primarily to connect elements, spaces, or facilities within a site is not a trail. Trailhead. An outdoor space that is designated by an entity responsible for administering or maintaining a trail to serve as an access point to the trail. The junction of two or more trails or the undeveloped junction of a trail and a road is not a trailhead. Transfer Device. Equipment designed to facilitate the transfer of a person from a wheelchair or other mobility aid to and from an amusement ride seat. Transient Lodging. A building or facility containing one or more guest room(s) for sleeping that provides accommodations that are primarily short-term in nature. Transient lodging does not include residential dwelling units intended to be used as a residence, inpatient medical care facilities, licensed long-term care facilities, detention or correctional facilities, or private buildings or facilities that contain not more than five rooms for rent or hire and that are actually occupied by the proprietor as the residence of such proprietor. Transition Plate. A sloping pedestrian walking surface located at the end(s) of a gangway. TTY. An abbreviation for teletypewriter. Machinery that employs interactive text- PO 00000 Frm 00037 Fmt 4701 Sfmt 4700 59511 based communication through the transmission of coded signals across the telephone network. TTYs may include, for example, devices known as TDDs (telecommunication display devices or telecommunication devices for deaf persons) or computers with special modems. TTYs are also called text telephones. Use Zone. The ground level area beneath and immediately adjacent to a play structure or play equipment that is designated by ASTM F 1487 (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1) for unrestricted circulation around the play equipment and where it is predicted that a user would land when falling from or exiting the play equipment. Vehicular Way. A route provided for vehicular traffic, such as in a street, driveway, or parking facility. Viewing Area. An outdoor space developed for viewing landscapes, wildlife, or other points of interest. Walk. An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts. Wheelchair Space. Space for a single wheelchair and its occupant. Work Area Equipment. Any machine, instrument, engine, motor, pump, conveyor, or other apparatus used to perform work. As used in this document, this term shall apply only to equipment that is permanently installed or built-in in employee work areas subject to the Americans with Disabilities Act of 1990 (ADA). Work area equipment does not include passenger elevators and other accessible means of vertical transportation. ABA CHAPTER 2: SCOPING REQUIREMENTS F201 Application F201.1 Scope. All areas of newly designed and newly constructed buildings and facilities and altered or leased portions of existing buildings and facilities shall comply with these requirements. F201.2 Application Based on Building or Facility Use. Where a site, building, facility, room, or space contains more than one use, each portion shall comply with the applicable requirements for that use. F201.3 Temporary and Permanent Structures. These requirements shall apply to temporary and permanent buildings and facilities. F201.4 Requirements Apply to Facilities Constructed or Altered by or on Behalf of Federal Agencies. The requirements in F216.13, F244 through F248, and 1011 through 1019 shall apply only to facilities constructed or altered by federal agencies or by non-federal entities on federal land on behalf of federal agencies pursuant to a concession contract, partnership agreement, or similar arrangement. F201.4.1 Documentation and Notification When Exceptions Used for Trails and Beach Access Routes. Federal agencies shall document the basis for not fully complying with a specific provision in 1017 or 1018 on a portion of a trail or beach access route based on Exception 1 in 1017 or Exception 1 in 1018, and shall maintain the documentation with the records for the trail E:\FR\FM\26SER2.SGM 26SER2 59512 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 or beach project. Federal agencies shall notify the Access Board if an entire trail is exempted from complying with 1017 based on Exception 2 in 1017.1, and if a beach access route is not provided based on Exception 2 in 1018.1. F202 Existing Buildings and Facilities F202.1 General. Additions and alterations to existing buildings or facilities, including leased buildings or facilities, shall comply with F202. F202.2 Additions. Each addition to an existing building or facility shall comply with the requirements for new construction. F202.2.1 Accessible Route. At least one accessible route shall be provided within the site from accessible parking spaces and accessible passenger loading zones; public streets and sidewalks; and public transportation stops to an accessible entrance serving the addition. If the only accessible entrances serving the addition are provided in the existing building or facility, the accessible route shall connect at least one existing entrance to all accessible spaces and elements within the addition. In addition, elements and spaces specified in F202.2.2 through F202.2.5 shall be on an accessible route. F202.2.2 Entrance. Where an entrance is not provided in an addition, at least one entrance in the existing building or facility shall comply with F206.4 and shall serve the addition. F202.2.3 Toilet and Bathing Facilities. Where toilet facilities and bathing facilities are not provided in an addition but are provided in the existing building or facility to serve the addition, the toilet facilities and bathing facilities shall comply with F202.2.3. EXCEPTION: In alterations to areas serving additions where it is technically infeasible to comply with 603, altering existing toilet or bathing rooms is not required where a single unisex toilet room or bathing room complying with F213.2.1 is provided to serve the addition. F202.2.3.1 Existing Toilet Facility. Where existing toilet facilities are provided in the existing building or facility, at least one toilet facility for men and at least one toilet facility for women shall comply with F213.2 and F213.3 and shall serve the addition. EXCEPTION: Where only one toilet facility is provided in the existing building or facility, one toilet facility shall comply with F213.2 and F213.3 and shall serve the addition. F202.2.3.2 Existing Bathing Facility. Where existing bathing facilities are provided in the existing building or facility, at least one bathing facility for men and at least one bathing facility for women shall comply with F213.2 and F213.3 and shall serve the addition. EXCEPTION: Where only one bathing facility is provided in the existing building or facility, one bathing facility shall comply with F213.2 and F213.3 and shall serve the addition. F202.2.4 Public Telephone. Where a public telephone is not provided in an addition but is provided in the existing building or facility to serve the addition, at least one public telephone in the existing building or facility shall comply with F217. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 F202.2.5 Drinking Fountain. Where a drinking fountain is not provided in an addition but is provided in the existing building or facility to serve the addition, at least one drinking fountain in the existing building or facility shall comply with 602.1 through 602.6. F202.3 Alterations. Where existing elements or spaces are altered, each altered element or space shall comply with the applicable requirements of Chapter 2. EXCEPTIONS: 1. Unless required by F202.4, where elements or spaces are altered and the circulation path to the altered element or space is not altered, an accessible route shall not be required. 2. In alterations, where compliance with applicable requirements is technically infeasible, the alteration shall comply with the requirements to the maximum extent feasible. 3. Residential dwelling units not required to be accessible in compliance with a standard issued pursuant to the Architectural Barriers Act or Section 504 of the Rehabilitation Act of 1973, as amended, shall not be required to comply with F202.3. 4. Where elements or spaces are altered in camping facilities, picnic facilities, viewing areas, or trailheads and the circulation path to the altered element or space is not altered, the circulation path shall not be required to comply with 1016. F202.3.1 Prohibited Reduction in Access. An alteration that decreases or has the effect of decreasing the accessibility of a building or facility below the requirements for new construction at the time of the alteration is prohibited. F202.3.2 Extent of Application. An alteration of an existing element, space, or area of a building or facility shall not impose a requirement for accessibility greater than required for new construction. F202.4 Alterations Affecting Primary Function Areas. In addition to the requirements of F202.3, an alteration that affects or could affect the usability of or access to an area containing a primary function shall be made so as to ensure that, to the maximum extent feasible, the path of travel to the altered area, including the rest rooms, telephones, and drinking fountains serving the altered area, are readily accessible to and usable by individuals with disabilities, unless such alterations are disproportionate to the overall alterations in terms of cost and scope as determined under criteria established by the Administrator of the General Services Administration, the Secretary of Defense, the Secretary of Housing and Urban Development, or the United States Postal Service. EXCEPTIONS: 1. Residential dwelling units shall not be required to comply with F202.4. 2. Camping facilities, picnic facilities, viewing areas, trailheads, trails, and beach access routes shall not be required to comply with F202.4. F202.5 Alterations to Qualified Historic Buildings and Facilities. Alterations to a qualified historic building or facility shall comply with F202.3 and F202.4. EXCEPTION: Where the State Historic Preservation Officer or Advisory Council on PO 00000 Frm 00038 Fmt 4701 Sfmt 4700 Historic Preservation determines that compliance with the requirements for accessible routes, entrances, or toilet facilities would threaten or destroy the historic significance of the building or facility, the exceptions for alterations to qualified historic buildings or facilities for that element shall be permitted to apply. F202.6 Leases. Buildings or facilities for which new leases are negotiated by the Federal government after the effective date of the revised standards issued pursuant to the Architectural Barriers Act, including new leases for buildings or facilities previously occupied by the Federal government, shall comply with F202.6. EXCEPTIONS: 1. Buildings or facilities leased for use by officials servicing disasters on a temporary, emergency basis shall not be required to comply with F202.6. 2. Buildings or facilities leased for 12 months or less shall not be required to comply with F202.6 provided that the lease may not be extended or renewed. F202.6.1 Joint Use Areas. Joint use areas serving the leased space shall comply with F202.6. EXCEPTION: Alterations and additions to joint use areas serving the leased space shall not be required to comply with F202.2, F202.3, and F202.5 provided that the alterations are not undertaken by or on behalf of the Federal government. F202.6.2 Accessible Route. Primary function areas, as defined by Administrator of the General Services Administration, the Secretary of Defense, the Secretary of Housing and Urban Development, and the United States Postal Service, shall be served by at least one accessible route complying with F206. Elements and spaces required to be accessible by F202.6 shall be on an accessible route complying with F206. EXCEPTION: Fire alarms required by F202.6.5.2 and assistive listening systems required by F202.6.5.5 shall not be required to be on an accessible route. F202.6.3 Toilet and Bathing Facilities. Where provided, toilet facilities and bathing facilities shall comply with F202.6.3. F202.6.3.1 Multiple Facilities. At least one toilet facility or bathing facility for each sex on each floor that has toilet facilities or bathing facilities shall comply with F213.2 and F213.3. F202.6.3.2 Single Facilities. Where only one toilet or bathing facility is provided in a building or facility for each sex, either one unisex toilet or bathing facility, or one toilet or bathing facility for each sex, shall comply with F213.2 and F213.3. F202.6.4 Parking. Parking shall comply with F208. F202.6.5 Other Elements and Spaces. Where provided, the following elements and spaces shall comply with F202.6.5. F202.6.5.1 Drinking Fountains. Drinking fountains shall comply with F211. F202.6.5.2 Fire Alarms. Fire alarms shall comply with F215. EXCEPTION: Fire alarms shall not be required to comply with 702 where existing power sources must be upgraded to meet the requirement. F202.6.5.3 Public Telephones. Public telephones shall comply with F217. E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 F202.6.5.4 Dining Surfaces and Work Surfaces. Dining surfaces and work surfaces shall comply with F226. F202.6.5.5 Assembly Areas. Assistive listening systems shall comply with F219 and assembly seating shall comply with F221. F202.6.5.6 Sales and Service Counters. Sales and service counters shall comply with F227. F202.6.5.7 Depositories, Vending Machines, Change Machines, and Mail Boxes. Depositories, vending machines, change machines, and mail boxes shall comply with F228. F202.6.5.8 Residential Facilities. Residential dwelling units shall comply with F233. F203 General Exceptions F203.1 General. Sites, buildings, facilities, and elements are exempt from these requirements to the extent specified by F203. F203.2 Existing Elements. Elements in compliance with an earlier standard issued pursuant to the Architectural Barriers Act or Section 504 of the Rehabilitation Act of 1973, as amended shall not be required to comply with these requirements unless altered. F203.3 Construction Sites. Structures and sites directly associated with the actual processes of construction, including but not limited to, scaffolding, bridging, materials hoists, materials storage, and construction trailers shall not be required to comply with these requirements or to be on an accessible route. Portable toilet units provided for use exclusively by construction personnel on a construction site shall not be required to comply with F213 or to be on an accessible route. F203.4 Raised Areas. Areas raised primarily for purposes of security, life safety, or fire safety, including but not limited to, observation or lookout galleries, prison guard towers, fire towers, or life guard stands shall not be required to comply with these requirements or to be on an accessible route. F203.5 Limited Access Spaces. Spaces accessed only by ladders, catwalks, crawl spaces, or very narrow passageways shall not be required to comply with these requirements or to be on an accessible route. F203.6 Machinery Spaces. Spaces frequented only by service personnel for maintenance, repair, or occasional monitoring of equipment shall not be required to comply with these requirements or to be on an accessible route. Machinery spaces include, but are not limited to, elevator pits or elevator penthouses; mechanical, electrical or communications equipment rooms; piping or equipment catwalks; water or sewage treatment pump rooms and stations; electric substations and transformer vaults; and highway and tunnel utility facilities. F203.7 Single Occupant Structures. Single occupant structures accessed only by passageways below grade or elevated above standard curb height, including but not limited to, toll booths that are accessed only by underground tunnels, shall not be required to comply with these requirements or to be on an accessible route. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 F203.8 Detention and Correctional Facilities. In detention and correctional facilities, common use areas that are used only by inmates or detainees and security personnel and that do not serve holding cells or housing cells required to comply with F232, shall not be required to comply with these requirements or to be on an accessible route. F203.9 Residential Facilities. In residential facilities, common use areas that do not serve residential dwelling units required to provide mobility features complying with 809.2 through 809.4 shall not be required to comply with these requirements or to be on an accessible route. F203.10 Raised Refereeing, Judging, and Scoring Areas. Raised structures used solely for refereeing, judging, or scoring a sport shall not be required to comply with these requirements or to be on an accessible route. F203.11 Water Slides. Water slides shall not be required to comply with these requirements or to be on an accessible route. F203.12 Animal Containment Areas. Animal containment areas that are not for public use shall not be required to comply with these requirements or to be on an accessible route. F203.13 Raised Boxing or Wrestling Rings. Raised boxing or wrestling rings shall not be required to comply with these requirements or to be on an accessible route. F203.14 Raised Diving Boards and Diving Platforms. Raised diving boards and diving platforms shall not be required to comply with these requirements or to be on an accessible route. F204 Protruding Objects F204.1 General. Protruding objects on circulation paths shall comply with 307. EXCEPTIONS: 1. Within areas of sport activity, protruding objects on circulation paths shall not be required to comply with 307. 2. Within play areas, protruding objects on circulation paths shall not be required to comply with 307 provided that ground level accessible routes provide vertical clearance in compliance with 1008.2. F205 Operable Parts F205.1 General. Operable parts on accessible elements, accessible routes, and in accessible rooms and spaces shall comply with 309. EXCEPTIONS: 1. Operable parts that are intended for use only by service or maintenance personnel shall not be required to comply with 309. 2. Electrical or communication receptacles serving a dedicated use shall not be required to comply with 309. 3. Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309. 4. Floor electrical receptacles shall not be required to comply with 309. 5. HVAC diffusers shall not be required to comply with 309. 6. Except for light switches, where redundant controls are provided for a single element, one control in each space shall not be required to comply with 309. PO 00000 Frm 00039 Fmt 4701 Sfmt 4700 59513 7. Cleats and other boat securement devices shall not be required to comply with 309.3. 8. Exercise machines and exercise equipment shall not be required to comply with 309. F206 Accessible Routes F206.1 General. Accessible routes shall be provided in accordance with F206 and shall comply with Chapter 4 except that the exemptions at 403.5, 405.5, and 405.8 shall not apply. EXCEPTIONS: 1. Accessible routes shall not be required where outdoor recreation access routes are provided at camping facilities in accordance with F244.5, picnic facilities in accordance with F245.4, viewing areas in accordance with F246.3, or trailheads in accordance with F247.3.2. 2. Accessible routes shall not be required where camping facilities, picnic facilities, viewing areas, or outdoor constructed features are provided on trails. 3. Accessible routes shall not be required where beach access routes are provided in accordance with F248. F206.2 Where Required. Accessible routes shall be provided where required by F206.2. F206.2.1 Site Arrival Points. At least one accessible route shall be provided within the site from accessible parking spaces and accessible passenger loading zones; public streets and sidewalks; and public transportation stops to the accessible building or facility entrance they serve. EXCEPTIONS: 1. Where exceptions for alterations to qualified historic buildings or facilities are permitted by F202.5, no more than one accessible route from a site arrival point to an accessible entrance shall be required. 2. An accessible route shall not be required between site arrival points and the building or facility entrance if the only means of access between them is a vehicular way not providing pedestrian access. F206.2.2 Within a Site. At least one accessible route shall connect accessible buildings, accessible facilities, accessible elements, and accessible spaces that are on the same site. EXCEPTION: An accessible route shall not be required between accessible buildings, accessible facilities, accessible elements and accessible spaces if the only means of access between them is a vehicular way not providing pedestrian access. F206.2.3 Multi-Story Buildings and Facilities. At least one accessible route shall connect each story and mezzanine in multistory buildings and facilities. EXCEPTIONS: 1. Where a two story building or facility has one story with an occupant load of five or fewer persons that does not contain public use space, that story shall not be required to be connected to the story above or below. 2. In detention and correctional facilities, an accessible route shall not be required to connect stories where cells with mobility features required to comply with 807.2, all common use areas serving cells with mobility features required to comply with 807.2, and all public use areas are on an accessible route. E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 59514 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 3. In residential facilities, an accessible route shall not be required to connect stories where residential dwelling units with mobility features required to comply with 809.2 through 809.4, all common use areas serving residential dwelling units with mobility features required to comply with 809.2 through 809.4, and public use areas serving residential dwelling units are on an accessible route. 4. Within multi-story transient lodging guest rooms with mobility features required to comply with 806.2, an accessible route shall not be required to connect stories provided that spaces complying with 806.2 are on an accessible route and sleeping accommodations for two persons minimum are provided on a story served by an accessible route. 5. In air traffic control towers, an accessible route shall not be required to serve the cab and the floor immediately below the cab. 6. Where exceptions for alterations to qualified historic buildings or facilities are permitted by F202.5, an accessible route shall not be required to stories located above or below the accessible story. F206.2.3.1 Stairs and Escalators in Existing Buildings. In alterations and additions, where an escalator or stair is provided where none existed previously and major structural modifications are necessary for the installation, an accessible route shall be provided between the levels served by the escalator or stair unless exempted by F206.2.3 Exceptions 1 through 6. F206.2.4 Spaces and Elements. At least one accessible route shall connect accessible building or facility entrances with all accessible spaces and elements within the building or facility which are otherwise connected by a circulation path unless exempted by F206.2.3 Exceptions 1 through 6. EXCEPTIONS: 1. Raised courtroom stations, including judges’ benches, clerks’ stations, bailiffs’ stations, deputy clerks’ stations, and court reporters’ stations shall not be required to provide vertical access provided that the required clear floor space, maneuvering space, and, if appropriate, electrical service are installed at the time of initial construction to allow future installation of a means of vertical access complying with 405, 407, 408, or 410 without requiring substantial reconstruction of the space. 2. In assembly areas with fixed seating required to comply with F221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an accessible route are not provided. 3. Accessible routes shall not be required to connect mezzanines where buildings or facilities have no more than one story. In addition, accessible routes shall not be required to connect stories or mezzanines where multi-story buildings or facilities are exempted by F206.2.3 Exceptions 1 through 6. F206.2.5 Restaurants and Cafeterias. In restaurants and cafeterias, an accessible route shall be provided to all dining areas, including raised or sunken dining areas, and outdoor dining areas. EXCEPTIONS: 1. In alterations, an accessible route shall not be required to VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 existing raised or sunken dining areas, or to all parts of existing outdoor dining areas where the same services and decor are provided in an accessible space usable by the public and not restricted to use by people with disabilities. 2. In sports facilities, tiered dining areas providing seating required to comply with F221 shall be required to have accessible routes serving at least 25 percent of the dining area provided that accessible routes serve seating complying with F221 and each tier is provided with the same services. F206.2.6 Performance Areas. Where a circulation path directly connects a performance area to an assembly seating area, an accessible route shall directly connect the assembly seating area with the performance area. An accessible route shall be provided from performance areas to ancillary areas or facilities used by performers unless exempted by F206.2.3 Exceptions 1 through 6. F206.2.7 Press Boxes. Press boxes in assembly areas shall be on an accessible route. EXCEPTIONS: 1. An accessible route shall not be required to press boxes in bleachers that have points of entry at only one level provided that the aggregate area of all press boxes is 500 square feet (46 m2) maximum. 2. An accessible route shall not be required to free-standing press boxes that are elevated above grade 12 feet (3660 mm) minimum provided that the aggregate area of all press boxes is 500 square feet (46 m2) maximum. F206.2.8 Amusement Rides. Amusement rides required to comply with F234 shall provide accessible routes in accordance with F206.2.8. Accessible routes serving amusement rides shall comply with Chapter 4 except as modified by 1002.2. F206.2.8.1 Load and Unload Areas. Load and unload areas shall be on an accessible route. Where load and unload areas have more than one loading or unloading position, at least one loading and unloading position shall be on an accessible route. F206.2.8.2 Wheelchair Spaces, Ride Seats Designed for Transfer, and Transfer Devices. When amusement rides are in the load and unload position, wheelchair spaces complying with 1002.4, amusement ride seats designed for transfer complying with 1002.5, and transfer devices complying with 1002.6 shall be on an accessible route. F206.2.9 Recreational Boating Facilities. Boat slips required to comply with F235.2 and boarding piers at boat launch ramps required to comply with F235.3 shall be on an accessible route. Accessible routes serving recreational boating facilities shall comply with Chapter 4 except as modified by 1003.2. F206.2.10 Bowling Lanes. Where bowling lanes are provided, at least 5 percent, but no fewer than one of each type of bowling lane, shall be on an accessible route. F206.2.11 Court Sports. In court sports, at least one accessible route shall directly connect both sides of the court. F206.2.12 Exercise Machines and Equipment. Exercise machines and equipment required to comply with F236 shall be on an accessible route. F206.2.13 Fishing Piers and Platforms. Fishing piers and platforms shall be on an PO 00000 Frm 00040 Fmt 4701 Sfmt 4700 accessible route. Accessible routes serving fishing piers and platforms shall comply with Chapter 4 except as modified by 1005.1. F206.2.14 Golf Facilities. At least one accessible route shall connect accessible elements and spaces within the boundary of the golf course. In addition, accessible routes serving golf car rental areas; bag drop areas; course weather shelters complying with F238.2.3; course toilet rooms; and practice putting greens, practice teeing grounds, and teeing stations at driving ranges complying with F238.3 shall comply with Chapter 4 except as modified by 1006.2. EXCEPTION: Golf car passages complying with 1006.3 shall be permitted to be used for all or part of accessible routes required by F206.2.14. F206.2.15 Miniature Golf Facilities. Holes required to comply with F239.2, including the start of play, shall be on an accessible route. Accessible routes serving miniature golf facilities shall comply with Chapter 4 except as modified by 1007.2. F206.2.16 Play Areas. Play areas shall provide accessible routes in accordance with F206.2.16. Accessible routes serving play areas shall comply with Chapter 4 except as modified by 1008.2. F206.2.16.1 Ground Level and Elevated Play Components. At least one accessible route shall be provided within the play area. The accessible route shall connect ground level play components required to comply with F240.2.1 and elevated play components required to comply with F240.2.2, including entry and exit points of the play components. F206.2.16.2 Soft Contained Play Structures. Where three or fewer entry points are provided for soft contained play structures, at least one entry point shall be on an accessible route. Where four or more entry points are provided for soft contained play structures, at least two entry points shall be on an accessible route. F206.3 Location. Accessible routes shall coincide with or be located in the same area as general circulation paths. Where circulation paths are interior, required accessible routes shall also be interior. F206.4 Entrances. Entrances shall be provided in accordance with F206.4. Entrance doors, doorways, and gates shall comply with 404 and shall be on an accessible route complying with 402. EXCEPTIONS: 1. Where an alteration includes alterations to an entrance, and the building or facility has another entrance complying with 404 that is on an accessible route, the altered entrance shall not be required to comply with F206.4 unless required by F202.4. 2. Where exceptions for alterations to qualified historic buildings or facilities are permitted by F202.5, no more than one public entrance shall be required to comply with F206.4. Where no public entrance can comply with F206.4 under criteria established in F202.5 Exception, then either an unlocked entrance not used by the public shall comply with F206.4; or a locked entrance complying with F206.4 with a notification system or remote monitoring shall be provided. F206.4.1 Public Entrances. In addition to entrances required by F206.4.2 through E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations F206.4.9, at least 60 percent of all public entrances shall comply with 404. F206.4.2 Parking Structure Entrances. Where direct access is provided for pedestrians from a parking structure to a building or facility entrance, each direct access to the building or facility entrance shall comply with 404. F206.4.3 Entrances from Tunnels or Elevated Walkways. Where direct access is provided for pedestrians from a pedestrian tunnel or elevated walkway to a building or facility, at least one direct entrance to the building or facility from each tunnel or walkway shall comply with 404. F206.4.4 Transportation Facilities. In addition to the requirements of F206.4.2, F206.4.3, and F206.4.5 through F206.4.9, transportation facilities shall provide entrances in accordance with F206.4.4. F206.4.4.1 Location. In transportation facilities, where different entrances serve different transportation fixed routes or groups of fixed routes, at least one public entrance serving each fixed route or group of fixed routes shall comply with 404. F206.4.4.2 Direct Connections. Direct connections to other facilities shall provide an accessible route complying with 404 from the point of connection to boarding platforms and all transportation system elements required to be accessible. Any elements provided to facilitate future direct connections shall be on an accessible route connecting boarding platforms and all transportation system elements required to be accessible. F206.4.5 Tenant Spaces. At least one accessible entrance to each tenancy in a facility shall comply with 404. EXCEPTION: Self-service storage facilities not required to comply with F225.3 shall not be required to be on an accessible route. F206.4.6 Residential Dwelling Unit Primary Entrance. In residential dwelling units, at least one primary entrance shall comply with 404. The primary entrance to a residential dwelling unit shall not be to a bedroom. F206.4.7 Restricted Entrances. Where restricted entrances are provided to a building or facility, at least one restricted entrance to the building or facility shall comply with 404. F206.4.8 Service Entrances. If a service entrance is the only entrance to a building or to a tenancy in a facility, that entrance shall comply with 404. F206.4.9 Entrances for Inmates or Detainees. Where entrances used only by inmates or detainees and security personnel are provided at judicial facilities, detention facilities, or correctional facilities, at least one such entrance shall comply with 404. F206.5 Doors, Doorways, and Gates. Doors, doorways, and gates providing user passage shall be provided in accordance with F206.5. F206.5.1 Entrances. Each entrance to a building or facility required to comply with F206.4 shall have at least one door, doorway, or gate complying with 404. F206.5.2 Rooms and Spaces. Within a building or facility, at least one door, doorway, or gate serving each room or space complying with these requirements shall comply with 404. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 F206.5.3 Transient Lodging Facilities. In transient lodging facilities, entrances, doors, and doorways providing user passage into and within guest rooms that are not required to provide mobility features complying with 806.2 shall comply with 404.2.3. EXCEPTION: Shower and sauna doors in guest rooms that are not required to provide mobility features complying with 806.2 shall not be required to comply with 404.2.3. F206.5.4 Residential Dwelling Units. In residential dwelling units required to provide mobility features complying with 809.2 through 809.4, all doors and doorways providing user passage shall comply with 404. F206.6 Elevators. Elevators provided for passengers shall comply with 407. Where multiple elevators are provided, each elevator shall comply with 407. EXCEPTIONS: 1. In a building or facility permitted to use the exceptions to F206.2.3 or permitted by F206.7 to use a platform lift, elevators complying with 408 shall be permitted. 2. Elevators complying with 408 or 409 shall be permitted in multi-story residential dwelling units. F206.6.1 Existing Elevators. Where elements of existing elevators are altered, the same element shall also be altered in all elevators that are programmed to respond to the same hall call control as the altered elevator and shall comply with the requirements of 407 for the altered element. F206.7 Platform Lifts. Platform lifts shall comply with 410. Platform lifts shall be permitted as a component of an accessible route in new construction in accordance with F206.7. Platform lifts shall be permitted as a component of an accessible route in an existing building or facility. F206.7.1 Performance Areas and Speakers’ Platforms. Platform lifts shall be permitted to provide accessible routes to performance areas and speakers’ platforms. F206.7.2 Wheelchair Spaces. Platform lifts shall be permitted to provide an accessible route to comply with the wheelchair space dispersion and line-of-sight requirements of F221 and 802. F206.7.3 Incidental Spaces. Platform lifts shall be permitted to provide an accessible route to incidental spaces which are not public use spaces and which are occupied by five persons maximum. F206.7.4 Judicial Spaces. Platform lifts shall be permitted to provide an accessible route to: jury boxes and witness stands; raised courtroom stations including, judges’ benches, clerks’ stations, bailiffs’ stations, deputy clerks’ stations, and court reporters’ stations; and to depressed areas such as the well of a court. F206.7.5 Existing Site Constraints. Platform lifts shall be permitted where existing exterior site constraints make use of a ramp or elevator infeasible. F206.7.6 Guest Rooms and Residential Dwelling Units. Platform lifts shall be permitted to connect levels within transient lodging guest rooms required to provide mobility features complying with 806.2 or residential dwelling units required to provide mobility features complying with 809.2 through 809.4. PO 00000 Frm 00041 Fmt 4701 Sfmt 4700 59515 F206.7.7 Amusement Rides. Platform lifts shall be permitted to provide accessible routes to load and unload areas serving amusement rides. F206.7.8 Play Areas. Platform lifts shall be permitted to provide accessible routes to play components or soft contained play structures. F206.7.9 Team or Player Seating. Platform lifts shall be permitted to provide accessible routes to team or player seating areas serving areas of sport activity. F206.7.10 Recreational Boating Facilities and Fishing Piers and Platforms. Platform lifts shall be permitted to be used instead of gangways that are part of accessible routes serving recreational boating facilities and fishing piers and platforms. F206.8 Security Barriers. Security barriers, including but not limited to, security bollards and security check points, shall not obstruct a required accessible route or accessible means of egress. EXCEPTION: Where security barriers incorporate elements that cannot comply with these requirements such as certain metal detectors, fluoroscopes, or other similar devices, the accessible route shall be permitted to be located adjacent to security screening devices. The accessible route shall permit persons with disabilities passing around security barriers to maintain visual contact with their personal items to the same extent provided others passing through the security barrier. F207 Accessible Means of Egress F207.1 General. Means of egress shall comply with section 1003.2.13 of the International Building Code (2000 edition and 2001 Supplement) or section 1007 of the International Building Code (2003 edition) (incorporated by reference, see Referenced Standards’’ in Chapter 1). EXCEPTIONS: 1. Where means of egress are permitted by local building or life safety codes to share a common path of egress travel, accessible means of egress shall be permitted to share a common path of egress travel. 2. Areas of refuge shall not be required in detention and correctional facilities. F207.2 Platform Lifts. Standby power shall be provided for platform lifts permitted by section 1003.2.13.4 of the International Building Code (2000 edition and 2001 Supplement) or section 1007.5 of the International Building Code (2003 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1) to serve as a part of an accessible means of egress. F208 Parking Spaces F208.1 General. Where parking spaces are provided, parking spaces shall be provided in accordance with F208. EXCEPTION: Parking spaces used exclusively for buses, trucks, other delivery vehicles, law enforcement vehicles, or vehicular impound shall not be required to comply with F208 provided that lots accessed by the public are provided with a passenger loading zone complying with 503. F208.2 Minimum Number. Parking spaces complying with 502 shall be provided in accordance with Table F208.2 except as E:\FR\FM\26SER2.SGM 26SER2 59516 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations required by F208.2.1, F208.2.2, and F208.2.3. Where more than one parking facility is provided on a site, the number of accessible spaces provided on the site shall be calculated according to the number of spaces required for each parking facility. TABLE F208.2—PARKING SPACES Minimum number of required accessible parking spaces 1 to 25 ....................... 26 to 50 ..................... 51 to 75 ..................... 76 to 100 ................... 101 to 150 ................. 151 to 200 ................. 201 to 300 ................. 301 to 400 ................. 401 to 500 ................. 501 to 1000 ............... 1001 and over ........... emcdonald on DSK67QTVN1PROD with RULES2 Total number of parking spaces provided in parking facility 1. 2. 3. 4. 5. 6. 7. 8. 9. 2 percent of total. 20, plus 1 for each 100, or fraction thereof, over 1000. F208.2.1 Hospital Outpatient Facilities. Ten percent of patient and visitor parking spaces provided to serve hospital outpatient facilities shall comply with 502. F208.2.2 Rehabilitation Facilities and Outpatient Physical Therapy Facilities. Twenty percent of patient and visitor parking spaces provided to serve rehabilitation facilities specializing in treating conditions that affect mobility and outpatient physical therapy facilities shall comply with 502. F208.2.3 Residential Facilities. Parking spaces provided to serve residential facilities shall comply with F208.2.3. F208.2.3.1 Parking for Residents. Where at least one parking space is provided for each residential dwelling unit, at least one parking space complying with 502 shall be provided for each residential dwelling unit required to provide mobility features complying with 809.2 through 809.4. F208.2.3.2 Additional Parking Spaces for Residents. Where the total number of parking spaces provided for each residential dwelling unit exceeds one parking space per residential dwelling unit, 2 percent, but no fewer than one space, of all the parking spaces not covered by F208.2.3.1 shall comply with 502. F208.2.3.3 Parking for Guests, Employees, and Other Non-Residents. Where parking spaces are provided for persons other than residents, parking shall be provided in accordance with Table F208.2. F208.2.4 Van Parking Spaces. For every six or fraction of six parking spaces required by F208.2 to comply with 502, at least one shall be a van parking space complying with 502. F208.3 Location. Parking facilities shall comply with F208.3. F208.3.1 General. Parking spaces complying with 502 that serve a particular building or facility shall be located on the shortest accessible route from parking to an entrance complying with F206.4. Where parking serves more than one accessible entrance, parking spaces complying with 502 VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 shall be dispersed and located on the shortest accessible route to the accessible entrances. In parking facilities that do not serve a particular building or facility, parking spaces complying with 502 shall be located on the shortest accessible route to an accessible pedestrian entrance of the parking facility. EXCEPTIONS: 1. All van parking spaces shall be permitted to be grouped on one level within a multi-story parking facility. 2. Parking spaces shall be permitted to be located in different parking facilities if substantially equivalent or greater accessibility is provided in terms of distance from an accessible entrance or entrances, parking fee, and user convenience. F208.3.2 Residential Facilities. In residential facilities containing residential dwelling units required to provide mobility features complying with 809.2 through 809.4, parking spaces provided in accordance with F208.2.3.1 shall be located on the shortest accessible route to the residential dwelling unit entrance they serve. Spaces provided in accordance with F208.2.3.2 shall be dispersed throughout all types of parking provided for the residential dwelling units. EXCEPTION: Parking spaces provided in accordance with F208.2.3.2 shall not be required to be dispersed throughout all types of parking if substantially equivalent or greater accessibility is provided in terms of distance from an accessible entrance, parking fee, and user convenience. F209 Passenger Loading Zones and Bus Stops F209.1 General. Passenger loading zones shall be provided in accordance with F209. F209.2 Type. Where provided, passenger loading zones shall comply with F209.2. F209.2.1 Passenger Loading Zones. Passenger loading zones, except those required to comply with F209.2.2 and F209.2.3, shall provide at least one passenger loading zone complying with 503 in every continuous 100 linear feet (30 m) of loading zone space, or fraction thereof. F209.2.2 Bus Loading Zones. In bus loading zones restricted to use by designated or specified public transportation vehicles, each bus bay, bus stop, or other area designated for lift or ramp deployment shall comply with 810.2. F209.2.3 On-Street Bus Stops. On-street bus stops shall comply with 810.2 to the maximum extent practicable. F209.3 Medical Care and Long-Term Care Facilities. At least one passenger loading zone complying with 503 shall be provided at an accessible entrance to licensed medical care and licensed long-term care facilities where the period of stay exceeds twenty-four hours. F209.4 Valet Parking. Parking facilities that provide valet parking services shall provide at least one passenger loading zone complying with 503. F209.5 Mechanical Access Parking Garages. Mechanical access parking garages shall provide at least one passenger loading zone complying with 503 at vehicle drop-off and vehicle pick-up areas. PO 00000 Frm 00042 Fmt 4701 Sfmt 4700 F210 Stairways F210.1 General. Interior and exterior stairs that are part of a means of egress shall comply with 504. EXCEPTIONS: 1. In detention and correctional facilities, stairs that are not located in public use areas shall not be required to comply with 504. 2. In alterations, stairs between levels that are connected by an accessible route shall not be required to comply with 504, except that handrails complying with 505 shall be provided when the stairs are altered. 3. In assembly areas, aisle stairs shall not be required to comply with 504. 4. Stairs that connect play components shall not be required to comply with 504. F211 Drinking Fountains F211.1 General. Where drinking fountains are provided on an exterior site, on a floor, and within a secured area they shall be provided in accordance with F211. EXCEPTION: In detention or correctional facilities, drinking fountains only serving holding or housing cells not required to comply with F232 shall not be required to comply with F211. F211.2 Minimum Number. No fewer than two drinking fountains shall be provided. One drinking fountain shall comply with 602.1 through 602.6 and one drinking fountain shall comply with 602.7. EXCEPTION: Where a single drinking fountain complies with 602.1 through 602.6 and 602.7, it shall be permitted to be substituted for two separate drinking fountains. F211.3 More Than Minimum Number. Where more than the minimum number of drinking fountains specified in F211.2 are provided, 50 percent of the total number of drinking fountains provided shall comply with 602.1 through 602.6, and 50 percent of the total number of drinking fountains provided shall comply with 602.7. EXCEPTION: Where 50 percent of the drinking fountains yields a fraction, 50 percent shall be permitted to be rounded up or down provided that the total number of drinking fountains complying with F211 equals 100 percent of drinking fountains. F212 Kitchens, Kitchenettes, and Sinks F212.1 General. Where provided, kitchens, kitchenettes, and sinks shall comply with F212. F212.2 Kitchens and Kitchenettes. Kitchens and kitchenettes shall comply with 804. F212.3 Sinks. Where sinks are provided, at least 5 percent, but no fewer than one, of each type provided in each accessible room or space shall comply with 606. EXCEPTIONS: 1. Mop or service sinks shall not be required to comply with F212.3. 2. In camping facilities and picnic facilities, sinks shall not be required to comply with F212.3 where a cooktop or conventional range is not provided. F213 Toilet Facilities and Bathing Facilities F213.1 General. Where toilet facilities and bathing facilities are provided, they shall comply with F213. Where toilet facilities and E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations bathing facilities are provided in facilities permitted by F206.2.3 Exceptions 1 and 2 not to connect stories by an accessible route, toilet facilities and bathing facilities shall be provided on a story connected by an accessible route to an accessible entrance. EXCEPTION: Pit toilets provided on trails and in camping facilities shall not be required to comply with F213. F213.2 Toilet Rooms and Bathing Rooms. Where toilet rooms are provided, each toilet room shall comply with 603. Where bathing rooms are provided, each bathing room shall comply with 603. EXCEPTIONS: 1. In alterations where it is technically infeasible to comply with 603, altering existing toilet or bathing rooms shall not be required where a single unisex toilet room or bathing room complying with F213.2.1 is provided and located in the same area and on the same floor as existing inaccessible toilet or bathing rooms. 2. Where exceptions for alterations to qualified historic buildings or facilities are permitted by F202.5 and toilet rooms are provided, no fewer than one toilet room for each sex complying with 603 or one unisex toilet room complying with F213.2.1 shall be provided. 3. Where multiple single user portable toilet or bathing units are clustered at a single location, no more than 5 percent of the toilet units and bathing units at each cluster shall be required to comply with 603. Portable toilet units and bathing units complying with 603 shall be identified by the International Symbol of Accessibility complying with 703.7.2.1. 4. Where multiple single user toilet rooms are clustered at a single location, no more than 50 percent of the single user toilet rooms for each use at each cluster shall be required to comply with 603. F213.2.1 Unisex (Single-Use or Family) Toilet and Bathing Rooms. Unisex toilet rooms shall contain not more than one lavatory, and two water closets without urinals or one water closet and one urinal. Unisex bathing rooms shall contain one shower or one shower and one bathtub, one lavatory, and one water closet. Doors to unisex toilet rooms and unisex bathing rooms shall have privacy latches. F213.3 Plumbing Fixtures and Accessories. Plumbing fixtures and accessories provided in a toilet room or bathing room required to comply with F213.2 shall comply with F213.3. F213.3.1 Toilet Compartments. Where toilet compartments are provided, at least one toilet compartment shall comply with 604.8.1. In addition to the compartment required to comply with 604.8.1, at least one compartment shall comply with 604.8.2 where six or more toilet compartments are provided, or where the combination of urinals and water closets totals six or more fixtures. F213.3.2 Water Closets. Where water closets are provided at least one shall comply with 604. F213.3.3 Urinals. Where more than one urinal is provided, at least one shall comply with 605. F213.3.4 Lavatories. Where lavatories are provided, at least one shall comply with 606 VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 and shall not be located in a toilet compartment. F213.3.5 Mirrors. Where mirrors are provided, at least one shall comply with 603.3. F213.3.6 Bathing Facilities. Where bathtubs or showers are provided, at least one bathtub complying with 607 or at least one shower complying with 608 shall be provided. F213.3.7 Coat Hooks and Shelves. Where coat hooks or shelves are provided in toilet rooms without toilet compartments, at least one of each type shall comply with 603.4. Where coat hooks or shelves are provided in toilet compartments, at least one of each type complying with 604.8.3 shall be provided in toilet compartments required to comply with F213.3.1. Where coat hooks or shelves are provided in bathing facilities, at least one of each type complying with 603.4 shall serve fixtures required to comply with F213.3.6. F214 Washing Machines and Clothes Dryers F214.1 General. Where provided, washing machines and clothes dryers shall comply with F214. EXCEPTION: Washing machines and clothes dryers provided in employee work areas shall not be required to comply with F214. F214.2 Washing Machines. Where three or fewer washing machines are provided, at least one shall comply with 611. Where more than three washing machines are provided, at least two shall comply with 611. F214.3 Clothes Dryers. Where three or fewer clothes dryers are provided, at least one shall comply with 611. Where more than three clothes dryers are provided, at least two shall comply with 611. F215 Fire Alarm Systems F215.1 General. Where fire alarm systems provide audible alarm coverage, alarms shall comply with F215. EXCEPTION: In existing facilities, visible alarms shall not be required except where an existing fire alarm system is upgraded or replaced, or a new fire alarm system is installed. F215.2 Public and Common Use Areas. Alarms in public use areas and common use areas shall comply with 702. F215.3 Employee Work Areas. Where employee work areas have audible alarm coverage, the wiring system shall be designed so that visible alarms complying with 702 can be integrated into the alarm system. F215.4 Transient Lodging. Guest rooms required to comply with F224.4 shall provide alarms complying with 702. F215.5 Residential Facilities. Where provided in residential dwelling units required to comply with 809.5, alarms shall comply with 702. F216 Signs F216.1 General. Signs shall be provided in accordance with F216 and shall comply with 703. EXCEPTIONS: 1. Building directories, menus, seat and row designations in assembly areas, occupant names, building addresses, and company names and logos shall not be required to comply with F216. PO 00000 Frm 00043 Fmt 4701 Sfmt 4700 59517 2. In parking facilities, signs shall not be required to comply with F216.2, F216.3, and F216.6 through F216.12. 3. Temporary, 7 days or less, signs shall not be required to comply with F216. 4. In detention and correctional facilities, signs not located in public use areas shall not be required to comply with F216. F216.2 Designations. Interior and exterior signs identifying permanent rooms and spaces shall comply with 703.1, 703.2, and 703.5. Where pictograms are provided as designations of permanent interior rooms and spaces, the pictograms shall comply with 703.6 and shall have text descriptors complying with 703.2 and 703.5. EXCEPTION: Exterior signs that are not located at the door to the space they serve shall not be required to comply with 703.2. F216.3 Directional and Informational Signs. Signs that provide direction to or information about interior spaces and facilities of the site shall comply with 703.5. F216.4 Means of Egress. Signs for means of egress shall comply with F216.4. F216.4.1 Exit Doors. Doors at exit passageways, exit discharge, and exit stairways shall be identified by tactile signs complying with 703.1, 703.2, and 703.5. F216.4.2 Areas of Refuge. Signs required by section 1003.2.13.5.4 of the International Building Code (2000 edition) or section 1007.6.4 of the International Building Code (2003 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1) to provide instructions in areas of refuge shall comply with 703.5. F216.4.3 Directional Signs. Signs required by section 1003.2.13.6 of the International Building Code (2000 edition) or section 1007.7 of the International Building Code (2003 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1) to provide directions to accessible means of egress shall comply with 703.5. F216.5 Parking. Parking spaces complying with 502 shall be identified by signs complying with 502.6. EXCEPTIONS: 1. Where a total of four or fewer parking spaces, including accessible parking spaces, are provided on a site, identification of accessible parking spaces shall not be required. 2. In residential facilities, where parking spaces are assigned to specific residential dwelling units, identification of accessible parking spaces shall not be required. F216.6 Entrances. Where not all entrances comply with 404, entrances complying with 404 shall be identified by the International Symbol of Accessibility complying with 703.7.2.1. Directional signs complying with 703.5 that indicate the location of the nearest entrance complying with 404 shall be provided at entrances that do not comply with 404. F216.7 Elevators. Where existing elevators do not comply with 407, elevators complying with 407 shall be clearly identified with the International Symbol of Accessibility complying with 703.7.2.1. F216.8 Toilet Rooms and Bathing Rooms. Where existing toilet rooms or bathing rooms do not comply with 603, directional signs indicating the location of the nearest toilet room or bathing room complying with 603 E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 59518 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations within the facility shall be provided. Signs shall comply with 703.5 and shall include the International Symbol of Accessibility complying with 703.7.2.1. Where existing toilet rooms or bathing rooms do not comply with 603, the toilet rooms or bathing rooms complying with 603 shall be identified by the International Symbol of Accessibility complying with 703.7.2.1. Where clustered single user toilet rooms or bathing facilities are permitted to use exception to F213.2, toilet rooms or bathing facilities complying with 603 shall be identified by the International Symbol of Accessibility complying with 703.7.2.1 unless all toilet rooms and bathing facilities comply with 603. F216.9 TTYs. Identification and directional signs for public TTYs shall be provided in accordance with F216.9. F216.9.1 Identification Signs. Public TTYs shall be identified by the International Symbol of TTY complying with 703.7.2.2. F216.9.2 Directional Signs. Directional signs indicating the location of the nearest public TTY shall be provided at all banks of public pay telephones not containing a public TTY. In addition, where signs provide direction to public pay telephones, they shall also provide direction to public TTYs. Directional signs shall comply with 703.5 and shall include the International Symbol of TTY complying with 703.7.2.2. F216.10 Assistive Listening Systems. Each assembly area required by F219 to provide assistive listening systems shall provide signs informing patrons of the availability of the assistive listening system. Assistive listening signs shall comply with 703.5 and shall include the International Symbol of Access for Hearing Loss complying with 703.7.2.4. EXCEPTION: Where ticket offices or windows are provided, signs shall not be required at each assembly area provided that signs are displayed at each ticket office or window informing patrons of the availability of assistive listening systems. F216.11 Check-Out Aisles. Where more than one check-out aisle is provided, checkout aisles complying with 904.3 shall be identified by the International Symbol of Accessibility complying with 703.7.2.1. Where check-out aisles are identified by numbers, letters, or functions, signs identifying check-out aisles complying with 904.3 shall be located in the same location as the checkout aisle identification. EXCEPTION: Where all check-out aisles serving a single function comply with 904.3, signs complying with 703.7.2.1 shall not be required. F216.12 Amusement Rides. Signs identifying the type of access provided on amusement rides shall be provided at entries to queues and waiting lines. In addition, where accessible unload areas also serve as accessible load areas, signs indicating the location of the accessible load and unload areas shall be provided at entries to queues and waiting lines. F216.13 Trailhead Signs. Where new trail information signs are provided at trailheads on newly constructed or altered trails designed for use by hikers or pedestrians, the signs shall comply with 1017.10. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 F217 Telephones F217.1 General. Where coin-operated public pay telephones, coinless public pay telephones, public closed-circuit telephones, public courtesy phones, or other types of public telephones are provided, public telephones shall be provided in accordance with F217 for each type of public telephone provided. For purposes of this section, a bank of telephones shall be considered to be two or more adjacent telephones. F217.2 Wheelchair Accessible Telephones. Where public telephones are provided, wheelchair accessible telephones complying with 704.2 shall be provided in accordance with Table F217.2. EXCEPTION: Drive-up only public telephones shall not be required to comply with F217.2. TABLE F217.2—WHEELCHAIR ACCESSIBLE TELEPHONES Number of telephones provided on a floor, level, or exterior site Minimum number of required wheelchair accessible telephones 1 or more single units 1 per floor, level, and exterior site. 1 per floor, level, and exterior site. 1 per bank. 1 bank ....................... 2 or more banks ........ F217.3 Volume Controls. All public telephones shall have volume controls complying with 704.3. F217.4 TTYs. TTYs complying with 704.4 shall be provided in accordance with F217.4. F217.4.1 Bank Requirement. Where four or more public pay telephones are provided at a bank of telephones, at least one public TTY complying with 704.4 shall be provided at that bank. EXCEPTION: TTYs shall not be required at banks of telephones located within 200 feet (61 m) of, and on the same floor as, a bank containing a public TTY. F217.4.2 Floor Requirement. Where at least one public pay telephone is provided on a floor of a building, at least one public TTY shall be provided on that floor. F217.4.3 Building Requirement. Where at least one public pay telephone is provided in a public use area of a building, at least one public TTY shall be provided in the building in a public use area. F217.4.4 Exterior Site Requirement. Where four or more public pay telephones are provided on an exterior site, at least one public TTY shall be provided on the site. F217.4.5 Rest Stops, Emergency Roadside Stops, and Service Plazas. Where at least one public pay telephone is provided at a public rest stop, emergency roadside stop, or service plaza, at least one public TTY shall be provided. F217.4.6 Hospitals. Where at least one public pay telephone is provided serving a hospital emergency room, hospital recovery room, or hospital waiting room, at least one public TTY shall be provided at each location. F217.4.7 Transportation Facilities. In transportation facilities, in addition to the requirements of F217.4.1 through F217.4.4, where at least one public pay telephone PO 00000 Frm 00044 Fmt 4701 Sfmt 4700 serves a particular entrance to a bus or rail facility, at least one public TTY shall be provided to serve that entrance. In airports, in addition to the requirements of F217.4.1 through F217.4.4, where four or more public pay telephones are located in a terminal outside the security areas, a concourse within the security areas, or a baggage claim area in a terminal, at least one public TTY shall be provided in each location. F217.4.8 Detention and Correctional Facilities. In detention and correctional facilities, where at least one pay telephone is provided in a secured area used only by detainees or inmates and security personnel, at least one TTY shall be provided in at least one secured area. F217.5 Shelves for Portable TTYs. Where a bank of telephones in the interior of a building consists of three or more public pay telephones, at least one public pay telephone at the bank shall be provided with a shelf and an electrical outlet in accordance with 704.5. EXCEPTIONS: 1. Secured areas of detention and correctional facilities where shelves and outlets are prohibited for purposes of security or safety shall not be required to comply with F217.5. 2. The shelf and electrical outlet shall not be required at a bank of telephones with a TTY. F218 Transportation Facilities F218.1 General. Transportation facilities shall comply with F218. F218.2 New and Altered Fixed Guideway Stations. New and altered stations in rapid rail, light rail, commuter rail, intercity rail, high speed rail, and other fixed guideway systems shall comply with 810.5 through 810.10. F218.3 Bus Shelters. Where provided, bus shelters shall comply with 810.3 and 810.4. F218.4 Other Transportation Facilities. In other transportation facilities, public address systems shall comply with 810.7 and clocks shall comply with 810.8. F219 Assistive Listening Systems F219.1 General. Assistive listening systems shall be provided in accordance with F219 and shall comply with 706. F219.2 Required Systems. In each assembly area where audible communication is integral to the use of the space, an assistive listening system shall be provided. EXCEPTION: Other than in courtrooms, assistive listening systems shall not be required where audio amplification is not provided. F219.3 Receivers. Receivers complying with 706.2 shall be provided for assistive listening systems in each assembly area in accordance with Table F219.3. Twenty-five percent minimum of receivers provided, but no fewer than two, shall be hearing-aid compatible in accordance with 706.3. EXCEPTIONS: 1. Where a building contains more than one assembly area and the assembly areas required to provide assistive listening systems are under one management, the total number of required receivers shall be permitted to be calculated according to the total number of seats in the assembly areas in the building provided that all receivers are usable with all systems. E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 2. Where all seats in an assembly area are served by an induction loop assistive listening system, the minimum number of receivers required by Table F219.3 to be 59519 hearing-aid compatible shall not be required to be provided. TABLE F219.3—RECEIVERS FOR ASSISTIVE LISTENING SYSTEMS Capacity of seating in assembly area Minimum number of required receivers 50 or less ............................................................ 51 to 200 ............................................................ 201 to 500 .......................................................... 501 to 1000 ........................................................ 1001 to 2000 ...................................................... 2001 and over .................................................... 2 ....................................................................... 2, plus 1 per 25 seats over 50 seats ............... 2, plus 1 per 25 seats over 50 seats 1 ............ 20, plus 1 per 33 seats over 500 seats 1 ........ 35, plus 1 per 50 seats over 1000 seats 1 ...... 55, plus 1 per 100 seats over 2000 seats 1 .... 1 Or F220.1 General. Where automatic teller machines or self-service fare vending, collection, or adjustment machines are provided, at least one of each type provided at each location shall comply with 707. Where bins are provided for envelopes, waste paper, or other purposes, at least one of each type shall comply with 811. Assembly Areas F221.1 General. Assembly areas shall provide wheelchair spaces, companion seats, and designated aisle seats complying with F221 and 802. In addition, lawn seating shall comply with F221.5. F221.2 Wheelchair Spaces. Wheelchair spaces complying with F221.2 shall be provided in assembly areas with fixed seating. F221.2.1 Number and Location. Wheelchair spaces shall be provided complying with F221.2.1. F221.2.1.1 General Seating. Wheelchair spaces complying with 802.1 shall be provided in accordance with Table F221.2.1.1. TABLE F221.2.1.1—NUMBER OF WHEELCHAIR SPACES IN ASSEMBLY AREAS Number of seats 4 to 25 ....................... 26 to 50 ..................... 51 to 150 ................... 151 to 300 ................. 301 to 500 ................. 501 to 5000 ............... 5001 and over ........... emcdonald on DSK67QTVN1PROD with RULES2 2. 2. 1 per 1 per 1 per 1 per 4 4 4 4 receivers.1 receivers.1 receivers.1 receivers.1 fraction thereof. F220 Automatic Teller Machines and Fare Machines F221 Minimum number of required receivers required to be hearing-aid compatible Minimum number of required wheelchair spaces 1. 2. 4. 5. 6. 6, plus 1 for each 150, or fraction thereof, between 501 through 5000. 36, plus 1 for each 200, or fraction thereof, over 5000. F221.2.1.2 Luxury Boxes, Club Boxes, and Suites in Arenas, Stadiums, and Grandstands. In each luxury box, club box, and suite within arenas, stadiums, and grandstands, wheelchair spaces complying with 802.1 shall be provided in accordance with Table F221.2.1.1. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 F221.2.1.3 Other Boxes. In boxes other than those required to comply with F221.2.1.2, the total number of wheelchair spaces required shall be determined in accordance with Table F221.2.1.1. Wheelchair spaces shall be located in not less than 20 percent of all boxes provided. Wheelchair spaces shall comply with 802.1. F221.2.1.4 Team or Player Seating. At least one wheelchair space complying with 802.1 shall be provided in team or player seating areas serving areas of sport activity. EXCEPTION: Wheelchair spaces shall not be required in team or player seating areas serving bowling lanes not required to comply with F206.2.10. F221.2.2 Integration. Wheelchair spaces shall be an integral part of the seating plan. F221.2.3 Lines of Sight and Dispersion. Wheelchair spaces shall provide lines of sight complying with 802.2 and shall comply with F221.2.3. In providing lines of sight, wheelchair spaces shall be dispersed. Wheelchair spaces shall provide spectators with choices of seating locations and viewing angles that are substantially equivalent to, or better than, the choices of seating locations and viewing angles available to all other spectators. When the number of wheelchair spaces required by F221.2.1 has been met, further dispersion shall not be required. EXCEPTION: Wheelchair spaces in team or player seating areas serving areas of sport activity shall not be required to comply with F221.2.3. F221.2.3.1 Horizontal Dispersion. Wheelchair spaces shall be dispersed horizontally. EXCEPTIONS: 1. Horizontal dispersion shall not be required in assembly areas with 300 or fewer seats if the companion seats required by F221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length. Intermediate aisles shall be included in determining the total row length. If the row length in the 2nd and 3rd quartile of a row is insufficient to accommodate the required number of companion seats and wheelchair spaces, the additional companion seats and wheelchair spaces shall be permitted to be located in the 1st and 4th quartile of the row. 2. In row seating, two wheelchair spaces shall be permitted to be located side-by-side. F221.2.3.2 Vertical Dispersion. Wheelchair spaces shall be dispersed vertically at varying distances from the screen, performance area, or playing field. In addition, wheelchair spaces shall be located PO 00000 Frm 00045 Fmt 4701 Sfmt 4700 in each balcony or mezzanine that is located on an accessible route. EXCEPTIONS: 1. Vertical dispersion shall not be required in assembly areas with 300 or fewer seats if the wheelchair spaces provide viewing angles that are equivalent to, or better than, the average viewing angle provided in the facility. 2. In bleachers, wheelchair spaces shall not be required to be provided in rows other than rows at points of entry to bleacher seating. F221.3 Companion Seats. At least one companion seat complying with 802.3 shall be provided for each wheelchair space required by F221.2.1. F221.4 Designated Aisle Seats. At least 5 percent of the total number of aisle seats provided shall comply with 802.4 and shall be the aisle seats located closest to accessible routes. EXCEPTION: Team or player seating areas serving areas of sport activity shall not be required to comply with F221.4. F221.5 Lawn Seating. Lawn seating areas and exterior overflow seating areas, where fixed seats are not provided, shall connect to an accessible route. F222 Dressing, Fitting, and Locker Rooms F222.1 General. Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with 803. EXCEPTION: In alterations, where it is technically infeasible to provide rooms in accordance with F222.1, one room for each sex on each level shall comply with 803. Where only unisex rooms are provided, unisex rooms shall be permitted. F222.2 Coat Hooks and Shelves. Where coat hooks or shelves are provided in dressing, fitting or locker rooms without individual compartments, at least one of each type shall comply with 803.5. Where coat hooks or shelves are provided in individual compartments at least one of each type complying with 803.5 shall be provided in individual compartments in dressing, fitting, or locker rooms required to comply with F222.1. F223 Medical Care and Long-Term Care Facilities F223.1 General. In licensed medical care facilities and licensed long-term care facilities where the period of stay exceeds twenty-four hours, patient or resident E:\FR\FM\26SER2.SGM 26SER2 59520 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations sleeping rooms shall be provided in accordance with F223. EXCEPTION: Toilet rooms that are part of critical or intensive care patient sleeping rooms shall not be required to comply with 603. F223.1.1 Alterations. Where sleeping rooms are altered or added, the requirements of F223 shall apply only to the sleeping rooms being altered or added until the number of sleeping rooms complies with the minimum number required for new construction. F223.2 Hospitals, Rehabilitation Facilities, Psychiatric Facilities and Detoxification Facilities. Hospitals, rehabilitation facilities, psychiatric facilities and detoxification facilities shall comply with F223.2. F223.2.1 Facilities Not Specializing in Treating Conditions That Affect Mobility. In facilities not specializing in treating conditions that affect mobility, at least 10 percent, but no fewer than one, of the patient sleeping rooms shall provide mobility features complying with 805. F223.2.2 Facilities Specializing in Treating Conditions That Affect Mobility. In facilities specializing in treating conditions that affect mobility, 100 percent of the patient sleeping rooms shall provide mobility features complying with 805. F223.3 Long-Term Care Facilities. In licensed long-term care facilities, at least 50 percent, but no fewer than one, of each type of resident sleeping room shall provide mobility features complying with 805. F224 Transient Lodging Guest Rooms F224.1 General. Transient lodging facilities shall provide guest rooms in accordance with F224. F224.1.1 Alterations. Where guest rooms are altered or added, the requirements of F224 shall apply only to the guest rooms being altered or added until the number of guest rooms complies with the minimum number required for new construction. F224.1.2 Guest Room Doors and Doorways. Entrances, doors, and doorways providing user passage into and within guest rooms that are not required to provide mobility features complying with 806.2 shall comply with 404.2.3. EXCEPTION: Shower and sauna doors in guest rooms that are not required to provide mobility features complying with 806.2 shall not be required to comply with 404.2.3. F224.2 Guest Rooms with Mobility Features. In transient lodging facilities, guest rooms with mobility features complying with 806.2 shall be provided in accordance with Table F224.2. TABLE F224.2—GUEST ROOMS WITH MOBILITY FEATURES Total number of guest rooms provided Minimum number of required rooms without roll-in showers Minimum number of required rooms with roll-in showers Total number of required rooms 1 to 25 ............................................ 26 to 50 .......................................... 51 to 75 .......................................... 76 to 100 ........................................ 101 to 150 ...................................... 151 to 200 ...................................... 201 to 300 ...................................... 301 to 400 ...................................... 401 to 500 ...................................... 501 to 1000 .................................... 1001 and over ................................ 1 .................................................... 2 .................................................... 3 .................................................... 4 .................................................... 5 .................................................... 6 .................................................... 7 .................................................... 8 .................................................... 9 .................................................... 2 percent of total .......................... 20, plus 1 for each 100, or fraction thereof, over 1000. 0 .................................................... 0 .................................................... 1 .................................................... 1 .................................................... 2 .................................................... 2 .................................................... 3 .................................................... 4 .................................................... 4 .................................................... 1 percent of total .......................... 10, plus 1 for each 100, or fraction thereof, over 1000. 1. 2. 4. 5. 7. 8. 10. 12. 13. 3 percent of total. 30, plus 2 for each 100, or fraction thereof, over 1000. F224.3 Beds. In guest rooms having more than 25 beds, 5 percent minimum of the beds shall have clear floor space complying with 806.2.3. F224.4 Guest Rooms with Communication Features. In transient lodging facilities, guest rooms with communication features complying with 806.3 shall be provided in accordance with Table F224.4. TABLE F224.4—GUEST ROOMS WITH COMMUNICATION FEATURES emcdonald on DSK67QTVN1PROD with RULES2 Total number of guest rooms provided Minimum number of required guest rooms with communication features 2 to 25 ....................... 26 to 50 ..................... 51 to 75 ..................... 76 to 100 ................... 101 to 150 ................. 151 to 200 ................. 201 to 300 ................. 301 to 400 ................. 401 to 500 ................. 501 to 1000 ............... 1001 and over ........... 2. 4. 7. 9. 12. 14. 17. 20. 22. 5 percent of total. 50, plus 3 for each 100 over 1000. F224.5 Dispersion. Guest rooms required to provide mobility features complying with VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 806.2 and guest rooms required to provide communication features complying with 806.3 shall be dispersed among the various classes of guest rooms, and shall provide choices of types of guest rooms, number of beds, and other amenities comparable to the choices provided to other guests. Where the minimum number of guest rooms required to comply with 806 is not sufficient to allow for complete dispersion, guest rooms shall be dispersed in the following priority: guest room type, number of beds, and amenities. At least one guest room required to provide mobility features complying with 806.2 shall also provide communication features complying with 806.3. Not more than 10 percent of guest rooms required to provide mobility features complying with 806.2 shall be used to satisfy the minimum number of guest rooms required to provide communication features complying with 806.3. service shelving shall not be required to comply with 308. F225.3 Self-Service Storage Facilities. Self-service storage facilities shall provide individual self-service storage spaces complying with these requirements in accordance with Table F225.3. F225 Storage F225.1 General. Storage facilities shall comply with F225. F225.2 Storage. Where storage is provided in accessible spaces, at least one of each type shall comply with 811. F225.2.1 Lockers. Where lockers are provided, at least 5 percent, but no fewer than one of each type, shall comply with 811. F225.2.2 Self-Service Shelving. Selfservice shelves shall be located on an accessible route complying with 402. Self- F225.3.1 Dispersion. Individual selfservice storage spaces shall be dispersed throughout the various classes of spaces provided. Where more classes of spaces are provided than the number required to be accessible, the number of spaces shall not be required to exceed that required by Table F225.3. Self-service storage spaces complying with Table F225.3 shall not be required to be dispersed among buildings in a multibuilding facility. PO 00000 Frm 00046 Fmt 4701 Sfmt 4700 TABLE F225.3—SELF-SERVICE STORAGE FACILITIES Total spaces in facility 1 to 200 ..................... 201 and over ............. E:\FR\FM\26SER2.SGM 26SER2 Minimum number of spaces required to be accessible 5 percent, but no fewer than 1. 10, plus 2 percent of total number of units over 200. Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations F226 Dining Surfaces and Work Surfaces F226.1 General. Where dining surfaces are provided for the consumption of food or drink, at least 5 percent of the seating spaces and standing spaces at the dining surfaces shall comply with 902. In addition, where work surfaces are provided, at least 5 percent shall comply with 902. EXCEPTIONS: 1. Sales counters and service counters shall not be required to comply with 902. 2. Check writing surfaces provided at check-out aisles not required to comply with 904.3 shall not be required to comply with 902. F226.2 Dispersion. Dining surfaces and work surfaces required to comply with 902 shall be dispersed throughout the space or facility containing dining surfaces and work surfaces. F227 Sales and Service F227.1 General. Where provided, checkout aisles, sales counters, service counters, food service lines, queues, and waiting lines shall comply with F227 and 904. F227.2 Check-Out Aisles. Where checkout aisles are provided, check-out aisles complying with 904.3 shall be provided in accordance with Table F227.2. Where checkout aisles serve different functions, check-out aisles complying with 904.3 shall be provided in accordance with Table F227.2 for each function. Where check-out aisles are dispersed throughout the building or facility, check-out aisles complying with 904.3 shall be dispersed. EXCEPTION: Where the selling space is under 5000 square feet (465 m2) no more than one check-out aisle complying with 904.3 shall be required. TABLE F227.2—CHECK-OUT AISLES Minimum number of check-out aisles of each function required to comply with 904.3 1 to 4 ......................... 5 to 8 ......................... 9 to 15 ....................... 16 and over ............... emcdonald on DSK67QTVN1PROD with RULES2 Number of check-out aisles of each function 1. 2. 3. 3, plus 20 percent of additional aisles. F227.2.1 Altered Check-Out Aisles. Where check-out aisles are altered, at least one of each check-out aisle serving each function shall comply with 904.3 until the number of check-out aisles complies with F227.2. F227.3 Counters. Where provided, at least one of each type of sales counter and service counter shall comply with 904.4. Where counters are dispersed throughout the building or facility, counters complying with 904.4 also shall be dispersed. F227.4 Food Service Lines. Food service lines shall comply with 904.5. Where selfservice shelves are provided, at least 50 percent, but no fewer than one, of each type provided shall comply with 308. F227.5 Queues and Waiting Lines. Queues and waiting lines servicing counters or check-out aisles required to comply with 904.3 or 904.4 shall comply with 403. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 F228 Depositories, Vending Machines, Change Machines, Mail Boxes, and Fuel Dispensers F228.1 General. Where provided, at least one of each type of depository, vending machine, change machine, and fuel dispenser shall comply with 309. EXCEPTIONS: 1. Drive-up only depositories shall not be required to comply with 309. 2. Fuel dispensers provided for fueling official government vehicles shall not be required to comply with 309. F228.2 Mail Boxes. Where mail boxes are provided in an interior location, at least 5 percent, but no fewer than one, of each type shall comply with 309. In residential facilities, where mail boxes are provided for each residential dwelling unit, mail boxes complying with 309 shall be provided for each residential dwelling unit required to provide mobility features complying with 809.2 through 809.4. F229 Windows F229.1 General. Where glazed openings are provided in accessible rooms or spaces for operation by occupants, excluding employees, at least one opening shall comply with 309. In accessible rooms or spaces, each glazed opening required by an administrative authority to be operable shall comply with 309. EXCEPTIONS: 1. Glazed openings in residential dwelling units required to comply with 809 shall not be required to comply with F229. 2. Glazed openings in guest rooms required to provide communication features and in guest rooms required to comply with F206.5.3 shall not be required to comply with F229. F230 Two-Way Communication Systems F230.1 General. Where a two-way communication system is provided to gain admittance to a building or facility or to restricted areas within a building or facility, the system shall comply with 708. F231 Judicial Facilities F231.1 General. Judicial facilities shall comply with F231. F231.2 Courtrooms. Each courtroom shall comply with 808. F231.3 Holding Cells. Where provided, central holding cells and court-floor holding cells shall comply with F231.3. F231.3.1 Central Holding Cells. Where separate central holding cells are provided for adult male, juvenile male, adult female, or juvenile female, one of each type shall comply with 807.2. Where central holding cells are provided and are not separated by age or sex, at least one cell complying with 807.2 shall be provided. F231.3.2 Court-Floor Holding Cells. Where separate court-floor holding cells are provided for adult male, juvenile male, adult female, or juvenile female, each courtroom shall be served by one cell of each type complying with 807.2. Where court-floor holding cells are provided and are not separated by age or sex, courtrooms shall be served by at least one cell complying with 807.2. Cells may serve more than one courtroom. PO 00000 Frm 00047 Fmt 4701 Sfmt 4700 59521 F231.4 Visiting Areas. Visiting areas shall comply with F231.4. F231.4.1 Cubicles and Counters. At least 5 percent, but no fewer than one, of cubicles shall comply with 902 on both the visitor and detainee sides. Where counters are provided, at least one shall comply with 904.4.2 on both the visitor and detainee sides. EXCEPTION: The detainee side of cubicles or counters at non-contact visiting areas not serving holding cells required to comply with F231 shall not be required to comply with 902 or 904.4.2. F231.4.2 Partitions. Where solid partitions or security glazing separate visitors from detainees at least one of each type of cubicle or counter partition shall comply with 904.6. F232 Detention Facilities and Correctional Facilities F232.1 General. Buildings, facilities, or portions thereof, in which people are detained for penal or correction purposes, or in which the liberty of the inmates is restricted for security reasons shall comply with F232. F232.2 General Holding Cells and General Housing Cells. General holding cells and general housing cells shall be provided in accordance with F232.2. EXCEPTION: Alterations to cells shall not be required to comply except to the extent determined by regulations issued by the appropriate Federal agency having authority under section 504 of the Rehabilitation Act of 1973. F232.2.1 Cells with Mobility Features. At least 2 percent, but no fewer than one, of the total number of cells in a facility shall provide mobility features complying with 807.2. F232.2.1.1 Beds. In cells having more than 25 beds, at least 5 percent of the beds shall have clear floor space complying with 807.2.3. F232.2.2 Cells with Communication Features. At least 2 percent, but no fewer than one, of the total number of general holding cells and general housing cells equipped with audible emergency alarm systems and permanently installed telephones within the cell shall provide communication features complying with 807.3. F232.3 Special Holding Cells and Special Housing Cells. Where special holding cells or special housing cells are provided, at least one cell serving each purpose shall provide mobility features complying with 807.2. Cells subject to this requirement include, but are not limited to, those used for purposes of orientation, protective custody, administrative or disciplinary detention or segregation, detoxification, and medical isolation. EXCEPTION: Alterations to cells shall not be required to comply except to the extent determined by regulations issued by the appropriate Federal agency having authority under section 504 of the Rehabilitation Act of 1973. F232.4 Medical Care Facilities. Patient bedrooms or cells required to comply with F223 shall be provided in addition to any medical isolation cells required to comply with F232.3. E:\FR\FM\26SER2.SGM 26SER2 59522 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 F232.5 Visiting Areas. Visiting areas shall comply with F232.5. F232.5.1 Cubicles and Counters. At least 5 percent, but no fewer than one, of cubicles shall comply with 902 on both the visitor and detainee sides. Where counters are provided, at least one shall comply with 904.4.2 on both the visitor and detainee or inmate sides. EXCEPTION: The inmate or detainee side of cubicles or counters at non-contact visiting areas not serving holding cells or housing cells required to comply with F232 shall not be required to comply with 902 or 904.4.2. F232.5.2 Partitions. Where solid partitions or security glazing separate visitors from detainees or inmates at least one of each type of cubicle or counter partition shall comply with 904.6. F233 Residential Facilities F233.1 General. Facilities with residential dwelling units shall comply with F233. F233.2 Residential Dwelling Units Provided by HUD or Through Grant or Loan Programs Administered by HUD. Where facilities with residential dwelling units are provided by the Department of Housing and Urban Development (HUD), or through a grant or loan program administered by HUD, residential dwelling units with mobility features complying with 809.2 through 809.4 shall be provided in a number required by the regulations issued by HUD under Section 504 of the Rehabilitation Act of 1973, as amended. Residential dwelling units required to provide mobility features complying with 809.2 through 809.4 shall be on an accessible route as required by F206. In addition, residential dwelling units with communication features complying with 809.5 shall be provided in a number required by the applicable HUD regulations. Residential dwelling units subject to F233.2 shall not be required to comply with F233.3 or F233.4. F233.3 Residential Dwelling Units Provided on Military Installations. Military installations with residential dwelling units shall comply with F233.3. Residential dwelling units on military installations subject to F233.3 shall not be required to comply with F233.2 or F233.4. F233.3.1 Minimum Number: New Construction. Newly constructed facilities with residential dwelling units shall comply with F233.3.1. F233.3.1.1 Residential Dwelling Units with Mobility Features. On military installations with residential dwelling units, at least 5 percent, but no fewer than one unit, of the total number of residential dwelling units shall provide mobility features complying with 809.2 through 809.4 and shall be on an accessible route as required by F206. F233.3.1.2 Residential Dwelling Units with Communication Features. On military installations with residential dwelling units, at least 2 percent, but no fewer than one unit, of the total number of residential dwelling units shall provide communication features complying with 809.5. F233.3.2 Additions. Where an addition to an existing building results in an increase in the number of residential dwelling units, the requirements of F233.3.1 shall apply only to VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 the residential dwelling units that are added until the total number of residential dwelling units complies with the minimum number required by F233.3.1. Residential dwelling units required to comply with F233.3.1.1 shall be on an accessible route as required by F206. F233.3.3 Alterations. Alterations shall comply with F233.3.3. EXCEPTION: Where compliance with 809.2, 809.3, or 809.4 is technically infeasible, or where it is technically infeasible to provide an accessible route to a residential dwelling unit, the Department of Defense shall be permitted to alter or construct a comparable residential dwelling unit to comply with 809.2 through 809.4 provided that the minimum number of residential dwelling units required by F233.3.1.1 and F233.3.1.2, as applicable, is satisfied. F233.3.3.1 Alterations to Vacated Buildings. Where a building is vacated for the purposes of alteration, at least 5 percent of the residential dwelling units shall comply with 809.2 through 809.4 and shall be on an accessible route as required by F206. In addition, at least 2 percent of the residential dwelling units shall comply with 809.5. F233.3.3.2 Alterations to Individual Residential Dwelling Units. In individual residential dwelling units, where a bathroom or a kitchen is substantially altered, and at least one other room is altered, the requirements of F233.3.1 shall apply to the altered residential dwelling units until the total number of residential dwelling units complies with the minimum number required by F233.3.1.1 and F233.3.1.2. Residential dwelling units required to comply with F233.3.1.1 shall be on an accessible route as required by F206. F233.3.4 Dispersion. Residential dwelling units required to provide mobility features complying with 809.2 through 809.4 and residential dwelling units required provide communication features complying with 809.5 shall be dispersed among the various types of residential dwelling units on the military installation, and shall provide choices of residential dwelling units comparable to, and integrated with, those available to other residents. EXCEPTION: Where multi-story residential dwelling units are one of the types of residential dwelling units provided, onestory residential dwelling units shall be permitted as a substitute for multi-story residential dwelling units where equivalent spaces and amenities are provided in the one-story residential dwelling unit. F233.4 Residential Dwelling Units Provided by Other Federal Agencies or Through Grant or Loan Programs Administered by Other Federal Agencies. Facilities with residential dwelling units provided by other federal agencies or through grant or loan programs administered by other federal agencies shall comply with F233.4. Residential dwelling units subject to F233.4 shall not be required to comply with F233.2 or F233.3. F233.4.1 Minimum Number: New Construction. Newly constructed facilities with residential dwelling units shall comply with F233.4.1. PO 00000 Frm 00048 Fmt 4701 Sfmt 4700 EXCEPTION: Where facilities contain 15 or fewer residential dwelling units, the requirements of F233.4.1.1 and F233.4.1.2 shall apply to the total number of residential dwelling units that are constructed under a single contract, or are developed as a whole, whether or not located on a common site. F233.4.1.1 Residential Dwelling Units with Mobility Features. In facilities with residential dwelling units, at least 5 percent, but no fewer than one unit, of the total number of residential dwelling units shall provide mobility features complying with 809.2 through 809.4 and shall be on an accessible route as required by F206. F233.4.1.2 Residential Dwelling Units with Communication Features. In facilities with residential dwelling units, at least 2 percent, but no fewer than one unit, of the total number of residential dwelling units shall provide communication features complying with 809.5. F233.4.2 Residential Dwelling Units for Sale. Residential dwelling units offered for sale shall provide accessible features to the extent required by regulations issued by Federal agencies under Section 504 of the Rehabilitation Act of 1973, as amended. F233.4.3 Additions. Where an addition to an existing building results in an increase in the number of residential dwelling units, the requirements of F233.4.1 shall apply only to the residential dwelling units that are added until the total number of residential dwelling units complies with the minimum number required by F233.4.1. Residential dwelling units required to comply with F233.4.1.1 shall be on an accessible route as required by F206. F233.4.4 Alterations. Alterations shall comply with F233.4.4. EXCEPTION: Where compliance with 809.2, 809.3, or 809.4 is technically infeasible, or where it is technically infeasible to provide an accessible route to a residential dwelling unit, the entity shall be permitted to alter or construct a comparable residential dwelling unit to comply with 809.2 through 809.4 provided that the minimum number of residential dwelling units required by F233.4.1.1 and F233.4.1.2, as applicable, is satisfied. F233.4.4.1 Alterations to Vacated Buildings. Where a building is vacated for the purposes of alteration and the altered building contains more than 15 residential dwelling units, at least 5 percent of the residential dwelling units shall comply with 809.2 through 809.4 and shall be on an accessible route as required by F206. In addition, at least 2 percent of the residential dwelling units shall comply with 809.5. F233.4.4.2 Alterations to Individual Residential Dwelling Units. In individual residential dwelling units, where a bathroom or a kitchen is substantially altered, and at least one other room is altered the requirements of F233.4.1 shall apply to the altered residential dwelling units until the total number of residential dwelling units complies with the minimum number required by F233.4.1.1 and F233.4.1.2. Residential dwelling units required to comply with F233.4.1.1 shall be on an accessible route as required by F206. EXCEPTION: Where facilities contain 15 or fewer residential dwelling units, the E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations requirements of F233.4.1.1 and F233.4.1.2 shall apply to the total number of residential dwelling units that are altered under a single contract, or are developed as a whole, whether or not located on a common site. F233.4.5 Dispersion. Residential dwelling units required to provide mobility features complying with 809.2 through 809.4 and residential dwelling units required to provide communication features complying with 809.5 shall be dispersed among the various types of residential dwelling units in the facility and shall provide choices of residential dwelling units comparable to, and integrated with, those available to other residents. EXCEPTION: Where multi-story residential dwelling units are one of the types of residential dwelling units provided, onestory residential dwelling units shall be permitted as a substitute for multi-story residential dwelling units where equivalent spaces and amenities are provided in the one-story residential dwelling unit. emcdonald on DSK67QTVN1PROD with RULES2 F234 Amusement Rides F234.1 General. Amusement rides shall comply with F234. EXCEPTION: Mobile or portable amusement rides shall not be required to comply with F234. F234.2 Load and Unload Areas. Load and unload areas serving amusement rides shall comply with 1002.3. F234.3 Minimum Number. Amusement rides shall provide at least one wheelchair space complying with 1002.4, or at least one amusement ride seat designed for transfer complying with 1002.5, or at least one transfer device complying with 1002.6. EXCEPTIONS: 1. Amusement rides that are controlled or operated by the rider shall not be required to comply with F234.3. 2. Amusement rides designed primarily for children, where children are assisted on and off the ride by an adult, shall not be required to comply with F234.3. 3. Amusement rides that do not provide amusement ride seats shall not be required to comply with F234.3. F234.4 Existing Amusement Rides. Where existing amusement rides are altered, the alteration shall comply with F234.4. F234.4.1 Load and Unload Areas. Where load and unload areas serving existing amusement rides are newly designed and constructed, the load and unload areas shall comply with 1002.3. F234.4.2 Minimum Number. Where the structural or operational characteristics of an amusement ride are altered to the extent that the amusement ride’s performance differs from that specified by the manufacturer or the original design, the amusement ride shall comply with F234.3. F235 Recreational Boating Facilities F235.1 General. Recreational boating facilities shall comply with F235. F235.2 Boat Slips. Boat slips complying with 1003.3.1 shall be provided in accordance with Table F235.2. Where the number of boat slips is not identified, each 40 feet (12 m) of boat slip edge provided along the perimeter of the pier shall be counted as one boat slip for the purpose of this section. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 TABLE F235.2—BOAT SLIPS Total number of boat slips provided in facility Minimum number of required accessible boat slips 1 to 25 ....................... 26 to 50 ..................... 51 to 100 ................... 101 to 150 ................. 151 to 300 ................. 301 to 400 ................. 401 to 500 ................. 501 to 600 ................. 601 to 700 ................. 701 to 800 ................. 801 to 900 ................. 901 to 1000 ............... 1001 and over ........... 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 12, plus 1 for every 100, or fraction thereof, over 1000. F235.2.1 Dispersion. Boat slips complying with 1003.3.1 shall be dispersed throughout the various types of boat slips provided. Where the minimum number of boat slips required to comply with 1003.3.1 has been met, no further dispersion shall be required. F235.3 Boarding Piers at Boat Launch Ramps. Where boarding piers are provided at boat launch ramps, at least 5 percent, but no fewer than one, of the boarding piers shall comply with 1003.3.2. F236 Exercise Machines and Equipment F236.1 General. At least one of each type of exercise machine and equipment shall comply with 1004. F237 Fishing Piers and Platforms F237.1 General. Fishing piers and platforms shall comply with 1005. F238 Golf Facilities F238.1 General. Golf facilities shall comply with F238. F238.2 Golf Courses. Golf courses shall comply with F238.2. F238.2.1 Teeing Grounds. Where one teeing ground is provided for a hole, the teeing ground shall be designed and constructed so that a golf car can enter and exit the teeing ground. Where two teeing grounds are provided for a hole, the forward teeing ground shall be designed and constructed so that a golf car can enter and exit the teeing ground. Where three or more teeing grounds are provided for a hole, at least two teeing grounds, including the forward teeing ground, shall be designed and constructed so that a golf car can enter and exit each teeing ground. EXCEPTION: In existing golf courses, the forward teeing ground shall not be required to be one of the teeing grounds on a hole designed and constructed so that a golf car can enter and exit the teeing ground where compliance is not feasible due to terrain. F238.2.2 Putting Greens. Putting greens shall be designed and constructed so that a golf car can enter and exit the putting green. F238.2.3 Weather Shelters. Where provided, weather shelters shall be designed and constructed so that a golf car can enter and exit the weather shelter and shall comply with 1006.4. PO 00000 Frm 00049 Fmt 4701 Sfmt 4700 59523 F238.3 Practice Putting Greens, Practice Teeing Grounds, and Teeing Stations at Driving Ranges. At least 5 percent, but no fewer than one, of practice putting greens, practice teeing grounds, and teeing stations at driving ranges shall be designed and constructed so that a golf car can enter and exit the practice putting greens, practice teeing grounds, and teeing stations at driving ranges. F239 Miniature Golf Facilities F239.1 General. Miniature golf facilities shall comply with F239. F239.2 Minimum Number. At least 50 percent of holes on miniature golf courses shall comply with 1007.3. F239.3 Miniature Golf Course Configuration. Miniature golf courses shall be configured so that the holes complying with 1007.3 are consecutive. Miniature golf courses shall provide an accessible route from the last hole complying with 1007.3 to the course entrance or exit without requiring travel through any other holes on the course. EXCEPTION: One break in the sequence of consecutive holes shall be permitted provided that the last hole on the miniature golf course is the last hole in the sequence. F240 Play Areas F240.1 General. Play areas for children ages 2 and over shall comply with F240. Where separate play areas are provided within a site for specific age groups, each play area shall comply with F240. EXCEPTIONS: 1. Play areas located in family child care facilities where the proprietor actually resides shall not be required to comply with F240. 2. In existing play areas, where play components are relocated for the purposes of creating safe use zones and the ground surface is not altered or extended for more than one use zone, the play area shall not be required to comply with F240. 3. Amusement attractions shall not be required to comply with F240. 4. Where play components are altered and the ground surface is not altered, the ground surface shall not be required to comply with 1008.2.6 unless required by F202.4. F240.1.1 Additions. Where play areas are designed and constructed in phases, the requirements of F240 shall apply to each successive addition so that when the addition is completed, the entire play area complies with all the applicable requirements of F240. F240.2 Play Components. Where provided, play components shall comply with F240.2. F240.2.1 Ground Level Play Components. Ground level play components shall be provided in the number and types required by F240.2.1. Ground level play components that are provided to comply with F240.2.1.1 shall be permitted to satisfy the additional number required by F240.2.1.2 if the minimum required types of play components are satisfied. Where two or more required ground level play components are provided, they shall be dispersed throughout the play area and integrated with other play components. F240.2.1.1 Minimum Number and Types. Where ground level play components are E:\FR\FM\26SER2.SGM 26SER2 59524 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations provided, at least one of each type shall be on an accessible route and shall comply with 1008.4. F240.2.1.2 Additional Number and Types. Where elevated play components are provided, ground level play components shall be provided in accordance with Table F240.2.1.2 and shall comply with 1008.4. EXCEPTION: If at least 50 percent of the elevated play components are connected by a ramp and at least 3 of the elevated play components connected by the ramp are different types of play components, the play area shall not be required to comply with F240.2.1.2. TABLE F240.2.1.2—NUMBER AND TYPES OF GROUND LEVEL PLAY COMPONENTS REQUIRED TO BE ON ACCESSIBLE ROUTES Number of elevated play components provided Minimum number of ground level play components required to be on an accessible route 1 .......................................................................... 2 to 4 .................................................................. 5 to 7 .................................................................. 8 to 10 ................................................................ 11 to 13 .............................................................. 14 to 16 .............................................................. 17 to 19 .............................................................. 20 to 22 .............................................................. 23 to 25 .............................................................. 26 and over ........................................................ Not applicable .................................................. 1 ....................................................................... 2 ....................................................................... 3 ....................................................................... 4 ....................................................................... 5 ....................................................................... 6 ....................................................................... 7 ....................................................................... 8 ....................................................................... 8, plus 1 for each additional 3, or fraction thereof, over 25. F240.2.2 Elevated Play Components. Where elevated play components are provided, at least 50 percent shall be on an accessible route and shall comply with 1008.4. F241 Saunas and Steam Rooms F241.1 General. Where provided, saunas and steam rooms shall comply with 612. EXCEPTION: Where saunas or steam rooms are clustered at a single location, no more than 5 percent of the saunas and steam rooms, but no fewer than one, of each type in each cluster shall be required to comply with 612. emcdonald on DSK67QTVN1PROD with RULES2 F242 Spas Swimming Pools, Wading Pools, and F242.1 General. Swimming pools, wading pools, and spas shall comply with F242. F242.2 Swimming Pools. At least two accessible means of entry shall be provided for swimming pools. Accessible means of entry shall be swimming pool lifts complying with 1009.2; sloped entries complying with 1009.3; transfer walls complying with 1009.4; transfer systems complying with 1009.5; and pool stairs complying with 1009.6. At least one accessible means of entry provided shall comply with 1009.2 or 1009.3. EXCEPTIONS: 1. Where a swimming pool has less than 300 linear feet (91 m) of swimming pool wall, no more than one accessible means of entry shall be required provided that the accessible means of entry is a swimming pool lift complying with 1009.2 or sloped entry complying with 1009.3. 2. Wave action pools, leisure rivers, sand bottom pools, and other pools where user access is limited to one area shall not be required to provide more than one accessible means of entry provided that the accessible means of entry is a swimming pool lift complying with 1009.2, a sloped entry complying with 1009.3, or a transfer system complying with 1009.5. 3. Catch pools shall not be required to provide an accessible means of entry VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 provided that the catch pool edge is on an accessible route. F242.3 Wading Pools. At least one accessible means of entry shall be provided for wading pools. Accessible means of entry shall comply with sloped entries complying with 1009.3. F242.4 Spas. At least one accessible means of entry shall be provided for spas. Accessible means of entry shall comply with swimming pool lifts complying with 1009.2; transfer walls complying with 1009.4; or transfer systems complying with 1009.5. EXCEPTION: Where spas are provided in a cluster, no more than 5 percent, but no fewer than one, spa in each cluster shall be required to comply with F242.4. F243 Shooting Facilities With Firing Positions F243.1 General. Where shooting facilities with firing positions are designed and constructed at a site, at least 5 percent, but no fewer than one, of each type of firing position shall comply with 1010. F244 Camping Facilities F244.1 General. Camping facilities, other than camping facilities on trails, shall comply with F244. F244.2 Camping Units with Mobility Features. Camping facilities shall provide camping units with mobility features complying with F244.2 in accordance with Table F244.2. Where a camping facility provides different types of camping units, Table F244.2 shall apply to each type of camping unit provided. TABLE F244.2—CAMPING UNITS WITH MOBILITY FEATURES Total number of camping units provided in camping facility 1 ................................ 2 to 25 ....................... 26 to 50 ..................... PO 00000 Frm 00050 Fmt 4701 Minimum number of camping units with mobility features required 1. 2. 3. Sfmt 4700 Minimum number of different types of ground level play components required to be on an accessible route Not applicable. 1. 2. 3. 3. 3. 3. 4. 4. 5. TABLE F244.2—CAMPING UNITS WITH MOBILITY FEATURES—Continued Total number of camping units provided in camping facility 51 to 75 ..................... 76 to 100 ................... 101 to 150 ................. 151 to 200 ................. 201 and over ............. Minimum number of camping units with mobility features required 4. 5. 7. 8. 8, plus 2 percent of the number over 200. F244.2.1 Alterations and Additions. Where camping units are altered or added, the requirements of F244.2 shall apply only to the camping units that are altered or added until the number of camping units with mobility features complies with the minimum number required in Table 244.2. EXCEPTION: Where an entity is implementing a transition plan for program accessibility developed pursuant to regulations issued under section 504 of the Rehabilitation Act that designates specific camping units to provide mobility features complying with F244.2, the entity shall not be required to comply with F244.2 when altering individual elements within camping units that are not designated to provide mobility features complying with F244.2. F244.2.2 Dispersion. Camping units required to provide mobility features complying with F244.2 shall provide choices of camping units comparable to, and integrated with, those available to others. F244.2.3 Elements Within Camping Units with Mobility Features. Elements within camping units required to provide mobility features shall comply with F244.2.3. F244.2.3.1 Outdoor Constructed Features. Where provided, at least one of each type of outdoor constructed features shall comply with 1011. Where more than one of the same type of outdoor constructed features is provided, at least two of the same type of E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations outdoor constructed features shall comply with 1011. F244.2.3.2 Parking Spaces. Where provided, parking spaces shall comply with F244.2.3.2. F244.2.3.2.1 Recreational Vehicles. Where parking spaces are provided for recreational vehicles, at least one parking space shall comply with 1012.2, 1012.4, and 1012.5. Where more than one parking space is provided for recreational vehicles, at least two parking spaces shall comply with 1012.2, 1012.4, and 1012.5. F244.2.3.2.2 Vehicles Other Than Recreational Vehicles. Where parking spaces are provided for vehicles other than recreational vehicles, at least one parking space shall comply with 1012.3, 1012.4, and 1012.5. Where more than one parking space is provided for a vehicle other than a recreational vehicle, at least two parking spaces shall comply with 1012.3, 1012.4, and 1012.5. 244.2.3.3 Tent Pads and Tent Platforms. Where provided, at least one tent pad and tent platform shall comply with 1013. Where more than one tent pad and tent platform is provided, at least two tent pads and tent platforms shall comply with 1013. F244.2.3.4 Camp Shelters. Where provided, at least one camp shelter shall comply with 1014. Where more than one camp shelter is provided, at least two camp shelters shall comply with 1014. F244.3 Outdoor Constructed Features in Common Use and Public Use Areas. Where provided in common use and public use areas that serve camping units with mobility features, at least 20 percent, but not less than one, of each type of outdoor constructed feature provided at each location shall comply with 1011. F244.4 Pull-up Spaces for Recreational Vehicles at Dump Stations. Where provided, pull-up spaces for recreational vehicles at dump stations shall comply with 1012.2, 1012.4, and 1012.5. F244.5 Outdoor Recreation Access Routes. Camping facilities shall provide outdoor recreation access routes complying with 1016 in accordance with F244.5. F244.5.1 Routes Within Camping Units with Mobility Features. At least one outdoor recreation access route shall connect accessible elements, spaces, and facilities provided within camping units with mobility features. F244.5.2 Routes to and Within Common Use and Public Use Areas. Common use and public use areas serving camping units with mobility features shall provide outdoor recreation access routes in accordance with F244.5.2. EXCEPTION: Outdoor recreation access routes shall not be required to connect camping units with mobility features and recreational vehicle dump stations where a pull-up space complying with 1012.2, 1012.4, and 1012.5 is provided at the dump station for recreational vehicles. F244.5.2.1 Routes to Common Use and Public Use Areas. At least one outdoor recreation access route shall connect each camping unit with mobility features with common use and public use areas serving the unit. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 F244.5.2.2 Routes Within Common Use and Public Use Areas. At least one outdoor recreation access route shall connect accessible elements, spaces, and facilities provided within common use and public use areas serving camping units with mobility features. F244.5.3 Routes to Adjacent Recreation Facilities. Where a circulation path connects camping facilities and adjacent recreation facilities, at least one outdoor recreation access route shall connect camping units with mobility features to an accessible route serving the adjacent recreation facilities. F244.5.4 Location. Outdoor recreation access routes required by F244.5.2 and F244.5.3 shall coincide with or be located in the same area as general circulation paths. F245 Picnic Facilities F245.1 General. Picnic facilities, other than picnic facilities on trails, shall comply with F245. F245.2 Picnic Units with Mobility Features. Picnic facilities shall provide picnic units with mobility features in accordance with F245.2. F245.2.1 Picnic Facilities with Two or Fewer Picnic Units. Where picnic facilities contain two or fewer picnic units, each picnic unit shall provide mobility features complying with F245.2. F245.2.2 Picnic Facilities with More Than Two Picnic Units. Where picnic facilities contain more than two picnic units, at least 20 percent, but not less than two, of the picnic units shall provide mobility features complying with F245.2. F245.2.3 Alterations and Additions. Where picnic units are altered or added, the requirements of F245.2 shall apply only to the picnic units that are altered or added until the number of picnic units with mobility features complies with the minimum number required in F245.2.1 or F245.2.2. EXCEPTION: Where an entity is implementing a transition plan for program accessibility developed pursuant to regulations issued under section 504 of the Rehabilitation Act that designates specific picnic units to provide mobility features complying with F245.2, the entity shall not be required to comply with F245.2 when altering individual elements within picnic units that are not designated to provide mobility features complying with F245.2. F245.2.4 Dispersion. Picnic units required to provide mobility features complying with F245.2 shall provide choices of picnic units comparable to, and integrated with, those available to others. F245.2.5 Elements Within Picnic Units with Mobility Features. Elements within picnic units required to provide mobility features shall comply with F245.2.5. F245.2.5.1 Outdoor Constructed Features. Where provided, at least one of each type of outdoor constructed feature shall comply with 1011. Where more than one of the same type of outdoor constructed feature is provided, at least two of the same type of outdoor constructed features shall comply with 1011. F245.2.5.2 Parking Spaces. Where provided, at least one parking space shall PO 00000 Frm 00051 Fmt 4701 Sfmt 4700 59525 comply with 1012.3, 1012.4, and 1012.5. Where more than one parking space is provided, at least two parking spaces shall comply with 1012.3, 1012.4, and 1012.5. F245.3 Outdoor Constructed Features in Common Use and Public Use Areas. Where provided in common use and public use areas that serve picnic units with mobility features, at least 20 percent, but not less than one, of each type of outdoor constructed feature provided at each location shall comply with 1011. F245.4 Outdoor Recreation Access Routes. Picnic facilities shall provide outdoor recreation access routes complying with 1016 in accordance with F245.4. F245.4.1 Routes Within Picnic Units with Mobility Features. At least one outdoor recreation access route shall connect accessible elements, spaces, and facilities provided within picnic units with mobility features. F245.4.2 Routes to and Within Common Use and Public Use Areas. Common use and public use areas serving picnic units with mobility features shall provide outdoor recreation access routes in accordance with F245.4.2. F245.4.2.1 Routes to Common Use and Public Use Areas. At least one outdoor recreation access route shall connect each picnic unit with mobility features with common use and public use areas serving that unit. F245.4.2.2 Routes Within Common Use and Public Use Areas. At least one outdoor recreation access route shall connect accessible elements, spaces, and facilities provided within common use and public use areas serving picnic units with mobility features. F245.4.3 Routes to Adjacent Recreation Facilities. Where a circulation path connects picnic facilities and adjacent recreation facilities, at least one outdoor recreation access route shall connect picnic units with mobility features to an accessible route serving the adjacent recreation facilities. F245.4.4 Location. Outdoor recreation access routes required by F245.4.2 and F245.4.3 shall coincide with or be located in the same area as general circulation paths. F246 Viewing Areas F246.1 General. Viewing areas, other than viewing areas on trails, shall comply with F246.1. F246.2 Distinct Viewing Locations. Each distinct viewing location within a viewing area shall comply with 1015. F246.3 Outdoor Constructed Features. Where provided within viewing areas, at least 20 percent, but not less than one, of each type of outdoor constructed feature shall comply with 1011. F246.4 Outdoor Recreation Access Routes. At least one outdoor recreation access route complying with 1016 shall connect accessible parking spaces or other arrival points serving the viewing area with accessible elements, spaces, and facilities provided within the viewing area. F247 Trails F247.1 General. Where a trail is designed for use by hikers or pedestrians and directly E:\FR\FM\26SER2.SGM 26SER2 59526 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 connects to a trailhead or another trail that substantially meets the requirements in 1017, the trail shall comply with 1017. F247.2 Existing Trails. Where the original design, function, or purpose of an existing trail is changed and the altered portion of the trail directly connects to a trailhead or another trail that substantially meets the requirements in 1017, the altered portion of the trail shall comply with 1017. F247.3 Trailheads. Trailheads shall comply with F247.3. F247.3.1 Outdoor Constructed Features. Where provided within trailheads, at least 20 percent, but not less than one, of each type of outdoor constructed feature shall comply with 1011. F247.3.2 Outdoor Recreation Access Routes. At least one outdoor recreation access route complying with 1016 shall connect the following: 1. Accessible parking spaces or other arrival points serving the trailhead; 2. Starting point of the trail; and 3. Accessible elements, spaces, and facilities provided within the trailhead. F247.4 Trail Facilities. Where provided on trails, facilities shall comply with F247.4. F247.4.1 Camping Facilities. Camping facilities provided on trails shall comply with F244.2 and F244.3. F247.4.2 Picnic Facilities. Picnic facilities provided on trails shall comply with F245.2 and F245.3. F247.4.3 Viewing Areas. Viewing areas provided on trails shall comply with F246.2 and F246.3. F247.4.4 Routes. Routes that connect trails complying with 1017 to camping facilities, picnic facilities, viewing areas, pit toilets, and accessible elements provided within the facilities shall comply with 1017. F247.5 Outdoor Constructed Features. Where outdoor constructed features are provided on trails, other than within facilities specified in F247.4, at least 20 percent, but not less than one, of each type of outdoor constructed feature at each location shall comply with 1011. F248 Beach Access Routes F248.1 General. Beach access routes complying with 1018 shall be provided in accordance with F248.1. Beach access routes shall be permanent or removable. EXCEPTION: Beach access routes shall not be required where pedestrian access to the beach is not permitted. F248.1.1 Facilities Serving Beaches. Beach access routes shall be provided in a number complying with F248.2 where the entity that administers or manages a beach constructs or alters any of the following facilities to serve the beach: 1. Circulation paths; 2. Parking facilities; 3. Toilet facilities; or 4. Bathing facilities. EXCEPTION: The entity shall not be required to expend more than 20 percent of the costs of constructing or altering the facilities to provide beach access routes. F248.1.2 Beach Nourishment. Beach access routes shall be provided in a number complying with F248.2 where the entity that administers or manages a beach undertakes a beach nourishment project. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 EXCEPTION: The entity shall not be required to expend more than 20 percent of the costs of a beach nourishment project to provide beach access routes. F248.2 Minimum Number. Where beach access routes are required by F248.1, at least one beach access route shall be provided for each 1/2 mile (0.8 km) of beach shoreline administered or managed by the entity. EXCEPTION: The number of beach access routes shall not be required to exceed the number of pedestrian access points provided by the entity to a beach. F248.3 Location. Beach access routes shall coincide with or be located in the same area as pedestrian access points to the beach. 7. Revise Appendix D to this part to read as follows: ■ Appendix D to Part 1191—Technical Chapter 3: Building Blocks 301 General 301.1 Scope. The provisions of Chapter 3 shall apply where required by Chapter 2 or where referenced by a requirement in this document. 302 Floor or Ground Surfaces 302.1 General. Floor and ground surfaces shall be stable, firm, and slip resistant and shall comply with 302. EXCEPTIONS: 1. Within animal containment areas, floor and ground surfaces shall not be required to be stable, firm, and slip resistant. 2. Areas of sport activity shall not be required to comply with 302. 302.2 Carpet. Carpet or carpet tile shall be securely attached and shall have a firm cushion, pad, or backing or no cushion or pad. Carpet or carpet tile shall have a level loop, textured loop, level cut pile, or level cut/uncut pile texture. Pile height shall be 1⁄2 inch (13 mm) maximum. Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with 303. 302.3 Openings. Openings in floor or ground surfaces shall not allow passage of a sphere more than 1⁄2 inch (13 mm) diameter except as allowed in 407.4.3, 409.4.3, 410.4, 810.5.3 and 810.10. Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel. 303 Changes in Level 303.1 General. Where changes in level are permitted in floor or ground surfaces, they shall comply with 303. EXCEPTIONS: 1. Animal containment areas shall not be required to comply with 303. 2. Areas of sport activity shall not be required to comply with 303. 303.2 Vertical. Changes in level of 1⁄4 inch (6.4 mm) high maximum shall be permitted to be vertical. 303.3 Beveled. Changes in level between 1⁄4 inch (6.4 mm) high minimum and 1⁄2 inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2. PO 00000 Frm 00052 Fmt 4701 Sfmt 4700 303.4 Ramps. Changes in level greater than 1⁄2 inch (13 mm) high shall be ramped, and shall comply with 405 or 406. 304 Turning Space 304.1 General. Turning space shall comply with 304. 304.2 Floor or Ground Surfaces. Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted. 304.3 Size. Turning space shall comply with 304.3.1 or 304.3.2. 304.3.1 Circular Space. The turning space shall be a space of 60 inches (1525 mm) diameter minimum. The space shall be permitted to include knee and toe clearance complying with 306. 304.3.2 T-Shaped Space. The turning space shall be a T-shaped space within a 60 inch (1525 mm) square minimum with arms and base 36 inches (915 mm) wide minimum. Each arm of the T shall be clear of obstructions 12 inches (305 mm) minimum in each direction and the base shall be clear of obstructions 24 inches (610 mm) minimum. The space shall be permitted to include knee and toe clearance complying with 306 only at the end of either the base or one arm. 304.4 Door Swing. Doors shall be permitted to swing into turning spaces. 305 Clear Floor or Ground Space 305.1 General. Clear floor or ground space shall comply with 305. 305.2 Floor or Ground Surfaces. Floor or ground surfaces of a clear floor or ground space shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted. 305.3 Size. The clear floor or ground space shall be 30 inches (760 mm) minimum by 48 inches (1220 mm) minimum. 305.4 Knee and Toe Clearance. Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306. 305.5 Position. Unless otherwise specified, clear floor or ground space shall be positioned for either forward or parallel approach to an element. 305.6 Approach. One full unobstructed side of the clear floor or ground space shall adjoin an accessible route or adjoin another clear floor or ground space. 305.7 Maneuvering Clearance. Where a clear floor or ground space is located in an alcove or otherwise confined on all or part of three sides, additional maneuvering clearance shall be provided in accordance with 305.7.1 and 305.7.2. 305.7.1 Forward Approach. Alcoves shall be 36 inches (915 mm) wide minimum where the depth exceeds 24 inches (610 mm). 305.7.2 Parallel Approach. Alcoves shall be 60 inches (1525 mm) wide minimum where the depth exceeds 15 inches (380 mm). 306 Knee and Toe Clearance 306.1 General. Where space beneath an element is included as part of clear floor or ground space or turning space, the space shall comply with 306. Additional space E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 shall not be prohibited beneath an element but shall not be considered as part of the clear floor or ground space or turning space. 306.2 Toe Clearance. 306.2.1 General. Space under an element between the finish floor or ground and 9 inches (230 mm) above the finish floor or ground shall be considered toe clearance and shall comply with 306.2. 306.2.2 Maximum Depth. Toe clearance shall extend 25 inches (635 mm) maximum under an element. 306.2.3 Minimum Required Depth. Where toe clearance is required at an element as part of a clear floor space, the toe clearance shall extend 17 inches (430 mm) minimum under the element. 306.2.4 Additional Clearance. Space extending greater than 6 inches (150 mm) beyond the available knee clearance at 9 inches (230 mm) above the finish floor or ground shall not be considered toe clearance. 306.2.5 Width. Toe clearance shall be 30 inches (760 mm) wide minimum. 306.3 Knee Clearance. 306.3.1 General. Space under an element between 9 inches (230 mm) and 27 inches (685 mm) above the finish floor or ground shall be considered knee clearance and shall comply with 306.3. 306.3.2 Maximum Depth. Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (230 mm) above the finish floor or ground. 306.3.3 Minimum Required Depth. Where knee clearance is required under an element as part of a clear floor space, the knee clearance shall be 11 inches (280 mm) deep minimum at 9 inches (230 mm) above the finish floor or ground, and 8 inches (205 mm) deep minimum at 27 inches (685 mm) above the finish floor or ground. 306.3.4 Clearance Reduction. Between 9 inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height. 306.3.5 Width. Knee clearance shall be 30 inches (760 mm) wide minimum. 307 Protruding Objects 307.1 General. Protruding objects shall comply with 307. 307.2 Protrusion Limits. Objects with leading edges more than 27 inches (685 mm) and not more than 80 inches (2030 mm) above the finish floor or ground shall protrude 4 inches (100 mm) maximum horizontally into the circulation path. EXCEPTION: Handrails shall be permitted to protrude 41⁄2 inches (115 mm) maximum. 307.3 Post-Mounted Objects. Freestanding objects mounted on posts or pylons shall overhang circulation paths 12 inches (305 mm) maximum when located 27 inches (685 mm) minimum and 80 inches (2030 mm) maximum above the finish floor or ground. Where a sign or other obstruction is mounted between posts or pylons and the clear distance between the posts or pylons is greater than 12 inches (305 mm), the lowest edge of such sign or obstruction shall be 27 inches (685 mm) maximum or 80 inches (2030 mm) minimum above the finish floor or ground. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 EXCEPTION: The sloping portions of handrails serving stairs and ramps shall not be required to comply with 307.3. 307.4 Vertical Clearance. Vertical clearance shall be 80 inches (2030 mm) high minimum. Guardrails or other barriers shall be provided where the vertical clearance is less than 80 inches (2030 mm) high. The leading edge of such guardrail or barrier shall be located 27 inches (685 mm) maximum above the finish floor or ground. EXCEPTION: Door closers and door stops shall be permitted to be 78 inches (1980 mm) minimum above the finish floor or ground. 307.5 Required Clear Width. Protruding objects shall not reduce the clear width required for accessible routes. 308 Reach Ranges 308.1 General. Reach ranges shall comply with 308. 308.2 Forward Reach. 308.2.1 Unobstructed. Where a forward reach is unobstructed, the high forward reach shall be 48 inches (1220 mm) maximum and the low forward reach shall be 15 inches (380 mm) minimum above the finish floor or ground. 308.2.2 Obstructed High Reach. Where a high forward reach is over an obstruction, the clear floor space shall extend beneath the element for a distance not less than the required reach depth over the obstruction. The high forward reach shall be 48 inches (1220 mm) maximum where the reach depth is 20 inches (510 mm) maximum. Where the reach depth exceeds 20 inches (510 mm), the high forward reach shall be 44 inches (1120 mm) maximum and the reach depth shall be 25 inches (635 mm) maximum. 308.3 Side Reach. 308.3.1 Unobstructed. Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1220 mm) maximum and the low side reach shall be 15 inches (380 mm) minimum above the finish floor or ground. EXCEPTIONS: 1. An obstruction shall be permitted between the clear floor or ground space and the element where the depth of the obstruction is 10 inches (255 mm) maximum. 2. Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs. 308.3.2 Obstructed High Reach. Where a clear floor or ground space allows a parallel approach to an element and the high side reach is over an obstruction, the height of the obstruction shall be 34 inches (865 mm) maximum and the depth of the obstruction shall be 24 inches (610 mm) maximum. The high side reach shall be 48 inches (1220 mm) maximum for a reach depth of 10 inches (255 mm) maximum. Where the reach depth exceeds 10 inches (255 mm), the high side reach shall be 46 inches (1170 mm) maximum for a reach depth of 24 inches (610 mm) maximum. EXCEPTIONS: 1. The top of washing machines and clothes dryers shall be permitted to be 36 inches (915 mm) maximum above the finish floor. 2. Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) PO 00000 Frm 00053 Fmt 4701 Sfmt 4700 59527 maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs. 309 Operable Parts 309.1 General. Operable parts shall comply with 309. 309.2 Clear Floor Space. A clear floor or ground space complying with 305 shall be provided. 309.3 Height. Operable parts shall be placed within one or more of the reach ranges specified in 308. 309.4 Operation. Operable parts shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist. The force required to activate operable parts shall be 5 pounds (22.2 N) maximum. EXCEPTION: Gas pump nozzles shall not be required to provide operable parts that have an activating force of 5 pounds (22.2 N) maximum. Chapter 4: Accessible Routes 401 General 401.1 Scope. The provisions of Chapter 4 shall apply where required by Chapter 2 or where referenced by a requirement in this document. 402 Accessible Routes 402.1 General. Accessible routes shall comply with 402. 402.2 Components. Accessible routes shall consist of one or more of the following components: walking surfaces with a running slope not steeper than 1:20, doorways, ramps, curb ramps excluding the flared sides, elevators, and platform lifts. All components of an accessible route shall comply with the applicable requirements of Chapter 4. 403 Walking Surfaces 403.1 General. Walking surfaces that are a part of an accessible route shall comply with 403. 403.2 Floor or Ground Surface. Floor or ground surfaces shall comply with 302. 403.3 Slope. The running slope of walking surfaces shall not be steeper than 1:20. The cross slope of walking surfaces shall not be steeper than 1:48. 403.4 Changes in Level. Changes in level shall comply with 303. 403.5 Clearances. Walking surfaces shall provide clearances complying with 403.5. EXCEPTION: Within employee work areas, clearances on common use circulation paths shall be permitted to be decreased by work area equipment provided that the decrease is essential to the function of the work being performed. 403.5.1 Clear Width. Except as provided in 403.5.2 and 403.5.3, the clear width of walking surfaces shall be 36 inches (915 mm) minimum. EXCEPTION: The clear width shall be permitted to be reduced to 32 inches (815 mm) minimum for a length of 24 inches (610 mm) maximum provided that reduced width segments are separated by segments that are 48 inches (1220 mm) long minimum and 36 inches (915 mm) wide minimum. 403.5.2 Clear Width at Turn. Where the accessible route makes a 180 degree turn around an element which is less than 48 E:\FR\FM\26SER2.SGM 26SER2 59528 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations inches (1220 mm) wide, clear width shall be 42 inches (1065 mm) minimum approaching the turn, 48 inches (1220 mm) minimum at the turn and 42 inches (1065 mm) minimum leaving the turn. EXCEPTION: Where the clear width at the turn is 60 inches (1525 mm) minimum compliance with 403.5.2 shall not be required. 403.5.3 Passing Spaces. An accessible route with a clear width less than 60 inches (1525 mm) shall provide passing spaces at intervals of 200 feet (61 m) maximum. Passing spaces shall be either: a space 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum; or, an intersection of two walking surfaces providing a T-shaped space complying with 304.3.2 where the base and arms of the T-shaped space extend 48 inches (1220 mm) minimum beyond the intersection. 403.6 Handrails. Where handrails are provided along walking surfaces with running slopes not steeper than 1:20 they shall comply with 505. minimum. There shall be no projections into the required clear opening width lower than 34 inches (865 mm) above the finish floor or ground. Projections into the clear opening width between 34 inches (865 mm) and 80 inches (2030 mm) above the finish floor or ground shall not exceed 4 inches (100 mm). EXCEPTIONS: 1. In alterations, a projection of 5⁄8 inch (16 mm) maximum into the required clear width shall be permitted for the latch side stop. 2. Door closers and door stops shall be permitted to be 78 inches (1980 mm) minimum above the finish floor or ground. 404.2.4 Maneuvering Clearances. Minimum maneuvering clearances at doors and gates shall comply with 404.2.4. Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance. EXCEPTION: Entry doors to hospital patient rooms shall not be required to provide the clearance beyond the latch side of the door. 404.2.4.1 Swinging Doors and Gates. Swinging doors and gates shall have maneuvering clearances complying with Table 404.2.4.1. 404 Doors, Doorways, and Gates 404.1 General. Doors, doorways, and gates that are part of an accessible route shall comply with 404. EXCEPTION: Doors, doorways, and gates designed to be operated only by security personnel shall not be required to comply with 404.2.7, 404.2.8, 404.2.9, 404.3.2 and 404.3.4 through 404.3.7. 404.2 Manual Doors, Doorways, and Manual Gates. Manual doors and doorways and manual gates intended for user passage shall comply with 404.2. 404.2.1 Revolving Doors, Gates, and Turnstiles. Revolving doors, revolving gates, and turnstiles shall not be part of an accessible route. 404.2.2 Double-Leaf Doors and Gates. At least one of the active leaves of doorways with two leaves shall comply with 404.2.3 and 404.2.4. 404.2.3 Clear Width. Door openings shall provide a clear width of 32 inches (815 mm) minimum. Clear openings of doorways with swinging doors shall be measured between the face of the door and the stop, with the door open 90 degrees. Openings more than 24 inches (610 mm) deep shall provide a clear opening of 36 inches (915 mm) TABLE 404.2.4.1—MANEUVERING CLEARANCES AT MANUAL SWINGING DOORS AND GATES Type of use Approach direction From From From From From From From Minimum maneuvering clearance Door or gate side front ............................................ front ............................................ hinge side ................................... hinge side ................................... hinge side ................................... latch side .................................... latch side .................................... Perpendicular to doorway Pull ...................................................... Push ................................................... Pull ...................................................... Pull ...................................................... Push ................................................... Pull ...................................................... Push ................................................... 60 48 60 54 42 48 42 inches inches inches inches inches inches inches (1525 (1220 (1525 (1370 (1065 (1220 (1065 mm) ......................... mm) ......................... mm) ......................... mm) ......................... mm) 2 ....................... mm) 4 ....................... mm) 4 ....................... Parallel to doorway (beyond latch side unless noted) 18 inches (455 mm). 0 inches (0 mm).1 36 inches (915 mm). 42 inches (1065 mm). 22 inches (560 mm).3 24 inches (610 mm). 24 inches (610 mm). 1 Add 12 inches (305 mm) if closer and latch are provided. 6 inches (150 mm) if closer and latch are provided. 3 Beyond hinge side. 4 Add 6 inches (150 mm) if closer is provided. 2 Add 404.2.4.2 Doorways without Doors or Gates, Sliding Doors, and Folding Doors. Doorways less than 36 inches (915 mm) wide without doors or gates, sliding doors, or folding doors shall have maneuvering clearances complying with Table 404.2.4.2. TABLE 404.2.4.2—MANEUVERING CLEARANCES AT DOORWAYS WITHOUT DOORS OR GATES, MANUAL SLIDING DOORS, AND MANUAL FOLDING DOORS Minimum maneuvering clearance Approach direction Parallel to doorway (beyond stop/latch side unless noted) Perpendicular to doorway emcdonald on DSK67QTVN1PROD with RULES2 From From From From Front ............................................................................ side 1 ........................................................................... pocket/hinge side ........................................................ stop/latch side ............................................................. 48 42 42 42 inches inches inches inches (1220 (1065 (1065 (1065 mm) mm) mm) mm) .......................................................... .......................................................... .......................................................... .......................................................... 0 inches (0 mm). 0 inches (0 mm). 22 inches (560 mm).2 24 inches (610 mm). 1 Doorway 2 Beyond with no door only. pocket/hinge side. 404.2.4.3 Recessed Doors and Gates. Maneuvering clearances for forward approach shall be provided when any obstruction within 18 inches (455 mm) of the latch side of a doorway projects more than VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 8 inches (205 mm) beyond the face of the door, measured perpendicular to the face of the door or gate. 404.2.4.4 Floor or Ground Surface. Floor or ground surface within required PO 00000 Frm 00054 Fmt 4701 Sfmt 4700 maneuvering clearances shall comply with 302. Changes in level are not permitted. EXCEPTIONS: 1. Slopes not steeper than 1:48 shall be permitted. E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 2. Changes in level at thresholds complying with 404.2.5 shall be permitted. 404.2.5 Thresholds. Thresholds, if provided at doorways, shall be 1⁄2 inch (13 mm) high maximum. Raised thresholds and changes in level at doorways shall comply with 302 and 303. EXCEPTION: Existing or altered thresholds 3⁄4 inch (19 mm) high maximum that have a beveled edge on each side with a slope not steeper than 1:2 shall not be required to comply with 404.2.5. 404.2.6 Doors in Series and Gates in Series. The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space. 404.2.7 Door and Gate Hardware. Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 309.4. Operable parts of such hardware shall be 34 inches (865 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground. Where sliding doors are in the fully open position, operating hardware shall be exposed and usable from both sides. EXCEPTIONS: 1. Existing locks shall be permitted in any location at existing glazed doors without stiles, existing overhead rolling doors or grilles, and similar existing doors or grilles that are designed with locks that are activated only at the top or bottom rail. 2. Access gates in barrier walls and fences protecting pools, spas, and hot tubs shall be permitted to have operable parts of the release of latch on self-latching devices at 54 inches (1370 mm) maximum above the finish floor or ground provided the self-latching devices are not also self-locking devices and operated by means of a key, electronic opener, or integral combination lock. 404.2.8 Closing Speed. Door and gate closing speed shall comply with 404.2.8. 404.2.8.1 Door Closers and Gate Closers. Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum. 404.2.8.2 Spring Hinges. Door and gate spring hinges shall be adjusted so that from the open position of 70 degrees, the door or gate shall move to the closed position in 1.5 seconds minimum. 404.2.9 Door and Gate Opening Force. Fire doors shall have a minimum opening force allowable by the appropriate administrative authority. The force for pushing or pulling open a door or gate other than fire doors shall be as follows: 1. Interior hinged doors and gates: 5 pounds (22.2 N) maximum. 2. Sliding or folding doors: 5 pounds (22.2 N) maximum. These forces do not apply to the force required to retract latch bolts or disengage other devices that hold the door or gate in a closed position. 404.2.10 Door and Gate Surfaces. Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 width of the door or gate. Parts creating horizontal or vertical joints in these surfaces shall be within 1⁄16 inch (1.6 mm) of the same plane as the other. Cavities created by added kick plates shall be capped. EXCEPTIONS: 1. Sliding doors shall not be required to comply with 404.2.10. 2. Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (255 mm) bottom smooth surface height requirement. 3. Doors and gates that do not extend to within 10 inches (255 mm) of the finish floor or ground shall not be required to comply with 404.2.10. 4. Existing doors and gates without smooth surfaces within 10 inches (255 mm) of the finish floor or ground shall not be required to provide smooth surfaces complying with 404.2.10 provided that if added kick plates are installed, cavities created by such kick plates are capped. 404.2.11 Vision Lights. Doors, gates, and side lights adjacent to doors or gates, containing one or more glazing panels that permit viewing through the panels shall have the bottom of at least one glazed panel located 43 inches (1090 mm) maximum above the finish floor. EXCEPTION: Vision lights with the lowest part more than 66 inches (1675 mm) from the finish floor or ground shall not be required to comply with 404.2.11. 404.3 Automatic and Power-Assisted Doors and Gates. Automatic doors and automatic gates shall comply with 404.3. Full-powered automatic doors shall comply with ANSI/BHMA A156.10 (incorporated by reference, see Referenced Standards’’ in Chapter 1). Low-energy and power-assisted doors shall comply with ANSI/BHMA A156.19 (1997 or 2002 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1). 404.3.1 Clear Width. Doorways shall provide a clear opening of 32 inches (815 mm) minimum in power-on and power-off mode. The minimum clear width for automatic door systems in a doorway shall be based on the clear opening provided by all leaves in the open position. 404.3.2 Maneuvering Clearance. Clearances at power-assisted doors and gates shall comply with 404.2.4. Clearances at automatic doors and gates without standby power and serving an accessible means of egress shall comply with 404.2.4. EXCEPTION: Where automatic doors and gates remain open in the power-off condition, compliance with 404.2.4 shall not be required. 404.3.3 Thresholds. Thresholds and changes in level at doorways shall comply with 404.2.5. 404.3.4 Doors in Series and Gates in Series. Doors in series and gates in series shall comply with 404.2.6. 404.3.5 Controls. Manually operated controls shall comply with 309. The clear floor space adjacent to the control shall be located beyond the arc of the door swing. 404.3.6 Break Out Opening. Where doors and gates without standby power are a part of a means of egress, the clear break out PO 00000 Frm 00055 Fmt 4701 Sfmt 4700 59529 opening at swinging or sliding doors and gates shall be 32 inches (815 mm) minimum when operated in emergency mode. EXCEPTION: Where manual swinging doors and gates comply with 404.2 and serve the same means of egress compliance with 404.3.6 shall not be required. 404.3.7 Revolving Doors, Revolving Gates, and Turnstiles. Revolving doors, revolving gates, and turnstiles shall not be part of an 405 Ramps 405.1 General. Ramps on accessible routes shall comply with 405. EXCEPTION: In assembly areas, aisle ramps adjacent to seating and not serving elements required to be on an accessible route shall not be required to comply with 405. 405.2 Slope. Ramp runs shall have a running slope not steeper than 1:12. EXCEPTION: In existing sites, buildings, and facilities, ramps shall be permitted to have running slopes steeper than 1:12 complying with Table 405.2 where such slopes are necessary due to space limitations. TABLE 405.2—MAXIMUM RAMP SLOPE AND RISE FOR EXISTING SITES, BUILDINGS, AND FACILITIES Slope 1 Steeper than 1:10 but not steeper than 1:8. Steeper than 1:12 but not steeper than 1:10. 1A Maximum rise 3 inches (75 mm). 6 inches (150 mm). slope steeper than 1:8 is prohibited. 405.3 Cross Slope. Cross slope of ramp runs shall not be steeper than 1:48. 405.4 Floor or Ground Surfaces. Floor or ground surfaces of ramp runs shall comply with 302. Changes in level other than the running slope and cross slope are not permitted on ramp runs. 405.5 Clear Width. The clear width of a ramp run and, where handrails are provided, the clear width between handrails shall be 36 inches (915 mm) minimum. EXCEPTION: Within employee work areas, the required clear width of ramps that are a part of common use circulation paths shall be permitted to be decreased by work area equipment provided that the decrease is essential to the function of the work being performed. 405.6 Rise. The rise for any ramp run shall be 30 inches (760 mm) maximum. 405.7 Landings. Ramps shall have landings at the top and the bottom of each ramp run. Landings shall comply with 405.7. 405.7.1 Slope. Landings shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted. 405.7.2 Width. The landing clear width shall be at least as wide as the widest ramp run leading to the landing. 405.7.3 Length. The landing clear length shall be 60 inches (1525 mm) long minimum. 405.7.4 Change in Direction. Ramps that change direction between runs at landings shall have a clear landing 60 inches (1525 E:\FR\FM\26SER2.SGM 26SER2 59530 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 mm) minimum by 60 inches (1525 mm) minimum. 405.7.5 Doorways. Where doorways are located adjacent to a ramp landing, maneuvering clearances required by 404.2.4 and 404.3.2 shall be permitted to overlap the required landing area. 405.8 Handrails. Ramp runs with a rise greater than 6 inches (150 mm) shall have handrails complying with 505. EXCEPTION: Within employee work areas, handrails shall not be required where ramps that are part of common use circulation paths are designed to permit the installation of handrails complying with 505. Ramps not subject to the exception to 405.5 shall be designed to maintain a 36 inch (915 mm) minimum clear width when handrails are installed. 405.9 Edge Protection. Edge protection complying with 405.9.1 or 405.9.2 shall be provided on each side of ramp runs and at each side of ramp landings. EXCEPTIONS: 1. Edge protection shall not be required on ramps that are not required to have handrails and have sides complying with 406.3. 2. Edge protection shall not be required on the sides of ramp landings serving an adjoining ramp run or stairway. 3. Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of 1⁄2 inch (13 mm) maximum within 10 inches (255 mm) horizontally of the minimum landing area specified in 405.7. 405.9.1 Extended Floor or Ground Surface. The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505. 405.9.2 Curb or Barrier. A curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground surface. 405.10 Wet Conditions. Landings subject to wet conditions shall be designed to prevent the accumulation of water. 406 Curb Ramps 406.1 General. Curb ramps accessible routes shall comply with 406, 405.2 through 405.5, and 405.10. 406.2 Counter Slope. Counter slopes of adjoining gutters and road surfaces immediately adjacent to the curb ramp shall not be steeper than 1:20. The adjacent surfaces at transitions at curb ramps to walks, gutters, and streets shall be at the same level. 406.3 Sides of Curb Ramps. Where provided, curb ramp flares shall not be steeper than 1:10. 406.4 Landings. Landings shall be provided at the tops of curb ramps. The landing clear length shall be 36 inches (915 mm) minimum. The landing clear width shall be at least as wide as the curb ramp, excluding flared sides, leading to the landing. EXCEPTION: In alterations, where there is no landing at the top of curb ramps, curb ramp flares shall be provided and shall not be steeper than 1:12. 406.5 Location. Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 lanes, parking spaces, or parking access aisles. Curb ramps at marked crossings shall be wholly contained within the markings, excluding any flared sides. 406.6 Diagonal Curb Ramps. Diagonal or corner type curb ramps with returned curbs or other well-defined edges shall have the edges parallel to the direction of pedestrian flow. The bottom of diagonal curb ramps shall have a clear space 48 inches (1220 mm) minimum outside active traffic lanes of the roadway. Diagonal curb ramps provided at marked crossings shall provide the 48 inches (1220 mm) minimum clear space within the markings. Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing. 406.7 Islands. Raised islands in crossings shall be cut through level with the street or have curb ramps at both sides. Each curb ramp shall have a level area 48 inches (1220 mm) long minimum by 36 inches (915 mm) wide minimum at the top of the curb ramp in the part of the island intersected by the crossings. Each 48 inch (1220 mm) minimum by 36 inch (915 mm) minimum area shall be oriented so that the 48 inch (1220 mm) minimum length is in the direction of the running slope of the curb ramp it serves. The 48 inch (1220 mm) minimum by 36 inch (915 mm) minimum areas and the accessible route shall be permitted to overlap. 407 Elevators 407.1 General. Elevators shall comply with 407 and with ASME A17.1 (incorporated by reference, see Referenced Standards’’ in Chapter 1). They shall be passenger elevators as classified by ASME A17.1. Elevator operation shall be automatic. 407.2 Elevator Landing Requirements. Elevator landings shall comply with 407.2. 407.2.1 Call Controls. Where elevator call buttons or keypads are provided, they shall comply with 407.2.1 and 309.4. Call buttons shall be raised or flush. EXCEPTION: Existing elevators shall be permitted to have recessed call buttons. 407.2.1.1 Height. Call buttons and keypads shall be located within one of the reach ranges specified in 308, measured to the centerline of the highest operable part. EXCEPTION: Existing call buttons and existing keypads shall be permitted to be located at 54 inches (1370 mm) maximum above the finish floor, measured to the centerline of the highest operable part. 407.2.1.2 Size. Call buttons shall be 3⁄4 inch (19 mm) minimum in the smallest dimension. EXCEPTION: Existing elevator call buttons shall not be required to comply with 407.2.1.2. 407.2.1.3 Clear Floor or Ground Space. A clear floor or ground space complying with 305 shall be provided at call controls. 407.2.1.4 Location. The call button that designates the up direction shall be located above the call button that designates the down direction. EXCEPTION: Destination-oriented elevators shall not be required to comply with 407.2.1.4. PO 00000 Frm 00056 Fmt 4701 Sfmt 4700 407.2.1.5 Signals. Call buttons shall have visible signals to indicate when each call is registered and when each call is answered. EXCEPTIONS: 1. Destination-oriented elevators shall not be required to comply with 407.2.1.5 provided that visible and audible signals complying with 407.2.2 indicating which elevator car to enter are provided. 2. Existing elevators shall not be required to comply with 407.2.1.5. 407.2.1.6 Keypads. Where keypads are provided, keypads shall be in a standard telephone keypad arrangement and shall comply with 407.4.7.2. 407.2.2 Hall Signals. Hall signals, including in-car signals, shall comply with 407.2.2. 407.2.2.1 Visible and Audible Signals. A visible and audible signal shall be provided at each hoist-way entrance to indicate which car is answering a call and the car’s direction of travel. Where in-car signals are provided, they shall be visible from the floor area adjacent to the hall call buttons. EXCEPTIONS: 1. Visible and audible signals shall not be required at each destination-oriented elevator where a visible and audible signal complying with 407.2.2 is provided indicating the elevator car designation information. 2. In existing elevators, a signal indicating the direction of car travel shall not be required. 407.2.2.2 Visible Signals. Visible signal fixtures shall be centered at 72 inches (1830 mm) minimum above the finish floor or ground. The visible signal elements shall be 21⁄2 inches (64 mm) minimum measured along the vertical centerline of the element. Signals shall be visible from the floor area adjacent to the hall call button. EXCEPTIONS: 1. Destination-oriented elevators shall be permitted to have signals visible from the floor area adjacent to the hoist-way entrance. 2. Existing elevators shall not be required to comply with 407.2.2.2. 407.2.2.3 Audible Signals. Audible signals shall sound once for the up direction and twice for the down direction, or shall have verbal annunciators that indicate the direction of elevator car travel. Audible signals shall have a frequency of 1500 Hz maximum. Verbal annunciators shall have a frequency of 300 Hz minimum and 3000 Hz maximum. The audible signal and verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the hall call button. EXCEPTIONS: 1. Destination-oriented elevators shall not be required to comply with 407.2.2.3 provided that the audible tone and verbal announcement is the same as those given at the call button or call button keypad. 2. Existing elevators shall not be required to comply with the requirements for frequency and dB range of audible signals. 407.2.2.4 Differentiation. Each destination-oriented elevator in a bank of elevators shall have audible and visible means for differentiation. 407.2.3 Hoist-way Signs. Signs at elevator hoist-ways shall comply with 407.2.3. 407.2.3.1 Floor Designation. Floor designations complying with 703.2 and E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 703.4.1 shall be provided on both jambs of elevator hoist-way entrances. Floor designations shall be provided in both tactile characters and braille. Tactile characters shall be 2 inches (51 mm) high minimum. A tactile star shall be provided on both jambs at the main entry level. 407.2.3.2 Car Designations. Destinationoriented elevators shall provide tactile car identification complying with 703.2 on both jambs of the hoist-way immediately below the floor designation. Car designations shall be provided in both tactile characters and braille. Tactile characters shall be 2 inches (51 mm) high minimum. 407.3 Elevator Door Requirements. Hoistway and car doors shall comply with 407.3. 407.3.1 Type. Elevator doors shall be the horizontal sliding type. Car gates shall be prohibited. 407.3.2 Operation. Elevator hoist-way and car doors shall open and close automatically. EXCEPTION: Existing manually operated hoist-way swing doors shall be permitted provided that they comply with 404.2.3 and 404.2.9. Car door closing shall not be initiated until the hoist-way door is closed. 407.3.3 Reopening Device. Elevator doors shall be provided with a reopening device complying with 407.3.3 that shall stop and reopen a car door and hoist-way door automatically if the door becomes obstructed by an object or person. EXCEPTION: Existing elevators with manually operated doors shall not be required to comply with 407.3.3. 407.3.3.1 Height. The device shall be activated by sensing an obstruction passing through the opening at 5 inches (125 mm) nominal and 29 inches (735 mm) nominal above the finish floor. 407.3.3.2 Contact. The device shall not require physical contact to be activated, although contact is permitted to occur before the door reverses. 407.3.3.3 Duration. Door reopening devices shall remain effective for 20 seconds minimum. 407.3.4 Door and Signal Timing. The minimum acceptable time from notification that a car is answering a call or notification of the car assigned at the means for the entry of destination information until the doors of that car start to close shall be calculated from the following equation: T = D/(1.5 ft/s) or T = D/(455 mm/s) = 5 seconds minimum where T equals the total time in seconds and D equals the distance (in feet or millimeters) from the point in the lobby or corridor 60 inches (1525 mm) directly in front of the farthest call button 59531 controlling that car to the centerline of its hoist-way door. EXCEPTIONS: 1. For cars with in-car lanterns, T shall be permitted to begin when the signal is visible from the point 60 inches (1525 mm) directly in front of the farthest hall call button and the audible signal is sounded. 2. Destination-oriented elevators shall not be required to comply with 407.3.4. 407.3.5 Door Delay. Elevator doors shall remain fully open in response to a car call for 3 seconds minimum. 407.3.6 Width. The width of elevator doors shall comply with Table 407.4.1. EXCEPTION: In existing elevators, a power-operated car door complying with 404.2.3 shall be permitted. 407.4 Elevator Car Requirements. Elevator cars shall comply with 407.4. 407.4.1 Car Dimensions. Inside dimensions of elevator cars and clear width of elevator doors shall comply with Table 407.4.1. EXCEPTION: Existing elevator car configurations that provide a clear floor area of 16 square feet (1.5 m2) minimum and also provide an inside clear depth 54 inches (1370 mm) minimum and a clear width 36 inches (915 mm) minimum shall be permitted. TABLE 407.4.1—ELEVATOR CAR DIMENSIONS Minimum dimensions Door location Door clear width Centered ............................ Side (off-centered) ............. Any .................................... Any .................................... 1A 42 36 36 36 inches inches inches inches (1065 mm) (915 mm) 1 (915 mm)1 (915 mm) 1 Inside car, back wall to front return Inside car, side to side ........ ........ ........ ........ 80 68 54 60 inches inches inches inches (2030 (1725 (1370 (1525 mm) ........ mm) ........ mm) ........ mm) 2 ...... 51 51 80 60 inches inches inches inches (1295 (1295 (2030 (1525 mm) ........ mm) ........ mm) ........ mm) 2 ...... Inside car, back wall to inside face of door 54 54 80 60 inches inches inches inches (1370 (1370 (2030 (1525 mm). mm). mm). mm).2 tolerance of minus 5/8 inch (16 mm) is permitted. car configurations that provide a turning space complying with 304 with the door closed shall be permitted. emcdonald on DSK67QTVN1PROD with RULES2 2 Other 407.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303. 407.4.3 Platform to Hoist-way Clearance. The clearance between the car platform sill and the edge of any hoist-way landing shall be 11⁄4 inch (32 mm) maximum. 407.4.4 Leveling. Each car shall be equipped with a self-leveling feature that will automatically bring and maintain the car at floor landings within a tolerance of 1⁄2 inch (13 mm) under rated loading to zero loading conditions. 407.4.5 Illumination. The level of illumination at the car controls, platform, car threshold and car landing sill shall be 5 foot candles (54 lux) minimum. 407.4.6 Elevator Car Controls. Where provided, elevator car controls shall comply with 407.4.6 and 309.4. EXCEPTION: In existing elevators, where a new car operating panel complying with 407.4.6 is provided, existing car operating panels shall not be required to comply with 407.4.6. 407.4.6.1 Location. Controls shall be located within one of the reach ranges specified in 308. EXCEPTIONS: 1. Where the elevator panel serves more than 16 openings and a parallel VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 approach is provided, buttons with floor designations shall be permitted to be 54 inches (1370 mm) maximum above the finish floor. 2. In existing elevators, car control buttons with floor designations shall be permitted to be located 54 inches (1370 mm) maximum above the finish floor where a parallel approach is provided. 407.4.6.2 Buttons. Car control buttons with floor designations shall comply with 407.4.6.2 and shall be raised or flush. EXCEPTION: In existing elevators, buttons shall be permitted to be recessed. 407.4.6.2.1 Size. Buttons shall be 3⁄4 inch (19 mm) minimum in their smallest dimension. 407.4.6.2.2 Arrangement. Buttons shall be arranged with numbers in ascending order. When two or more columns of buttons are provided they shall read from left to right. 407.4.6.3 Keypads. Car control keypads shall be in a standard telephone keypad arrangement and shall comply with 407.4.7.2. 407.4.6.4 Emergency Controls. Emergency controls shall comply with 407.4.6.4. PO 00000 Frm 00057 Fmt 4701 Sfmt 4700 407.4.6.4.1 Height. Emergency control buttons shall have their centerlines 35 inches (890 mm) minimum above the finish floor. 407.4.6.4.2 Location. Emergency controls, including the emergency alarm, shall be grouped at the bottom of the panel. 407.4.7 Designations and Indicators of Car Controls. Designations and indicators of car controls shall comply with 407.4.7. EXCEPTION: In existing elevators, where a new car operating panel complying with 407.4.7 is provided, existing car operating panels shall not be required to comply with 407.4.7. 407.4.7.1 Buttons. Car control buttons shall comply with 407.4.7.1. 407.4.7.1.1 Type. Control buttons shall be identified by tactile characters complying with 703.2. 407.4.7.1.2 Location. Raised character and braille designations shall be placed immediately to the left of the control button to which the designations apply. EXCEPTION: Where space on an existing car operating panel precludes tactile markings to the left of the controls, markings shall be placed as near to the control as possible. E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 59532 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 407.4.7.1.3 Symbols. The control button for the emergency stop, alarm, door open, door close, main entry door, and phone shall be identified with tactile symbols as shown in Figure 407.4.7.3 at the end of this document. 407.4.7.1.4 Visible Indicators. Buttons with floor designations shall be provided with visible indicators to show that a call has been registered. The visible indication shall extinguish when the car arrives at the designated floor. 407.4.7.2 Keypads. Keypads shall be identified by characters complying with 703.5 and shall be centered on the corresponding keypad button. The number five key shall have a single raised dot. The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 703.3.1. 407.4.8 Car Position Indicators. Audible and visible car position indicators shall be provided in elevator cars. 407.4.8.1 Visible Indicators. Visible indicators shall comply with 407.4.8.1. 407.4.8.1.1 Size. Characters shall be 1⁄2 inch (13 mm) high minimum. 407.4.8.1.2 Location. Indicators shall be located above the car control panel or above the door. 407.4.8.1.3 Floor Arrival. As the car passes a floor and when a car stops at a floor served by the elevator, the corresponding character shall illuminate. EXCEPTION: Destination-oriented elevators shall not be required to comply with 407.4.8.1.3 provided that the visible indicators extinguish when the call has been answered. 407.4.8.1.4 Destination Indicator. In destination-oriented elevators, a display shall be provided in the car with visible indicators to show car destinations. 407.4.8.2 Audible Indicators. Audible indicators shall comply with 407.4.8.2. 407.4.8.2.1 Signal Type. The signal shall be an automatic verbal annunciator which announces the floor at which the car is about to stop. EXCEPTION: For elevators other than destination-oriented elevators that have a rated speed of 200 feet per minute (1 m/s) or less, a non-verbal audible signal with a frequency of 1500 Hz maximum which sounds as the car passes or is about to stop at a floor served by the elevator shall be permitted. 407.4.8.2.2 Signal Level. The verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the annunciator. 407.4.8.2.3 Frequency. The verbal annunciator shall have a frequency of 300 Hz minimum to 3000 Hz maximum. 407.4.9 Emergency Communication. Emergency two-way communication systems shall comply with 308. Tactile symbols and characters shall be provided adjacent to the device and shall comply with 703.2. 408 Limited-Use/Limited-Application Elevators 408.1 General. Limited-use/limitedapplication elevators shall comply with 408 and with ASME A17.1 (incorporated by reference, see Referenced Standards’’ in VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 Chapter 1). They shall be passenger elevators as classified by ASME A17.1. Elevator operation shall be automatic. 408.2 Elevator Landings. Landings serving limited-use/limited-application elevators shall comply with 408.2. 408.2.1 Call Buttons. Elevator call buttons and keypads shall comply with 407.2.1. 408.2.2 Hall Signals. Hall signals shall comply with 407.2.2. 408.2.3 Hoist-way Signs. Signs at elevator hoist-ways shall comply with 407.2.3.1. 408.3 Elevator Doors. Elevator hoist-way doors shall comply with 408.3. 408.3.1 Sliding Doors. Sliding hoist-way and car doors shall comply with 407.3.1 through 407.3.3 and 408.4.1. 408.3.2 Swinging Doors. Swinging hoistway doors shall open and close automatically and shall comply with 404, 407.3.2 and 408.3.2. 408.3.2.1 Power Operation. Swinging doors shall be power-operated and shall comply with ANSI/BHMA A156.19 (1997 or 2002 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1). 408.3.2.2 Duration. Power-operated swinging doors shall remain open for 20 seconds minimum when activated. 408.4 Elevator Cars. Elevator cars shall comply with 408.4. 408.4.1 Car Dimensions and Doors. Elevator cars shall provide a clear width 42 inches (1065 mm) minimum and a clear depth 54 inches (1370 mm) minimum. Car doors shall be positioned at the narrow ends of cars and shall provide 32 inches (815 mm) minimum clear width. EXCEPTIONS: 1. Cars that provide a clear width 51 inches (1295 mm) minimum shall be permitted to provide a clear depth 51 inches (1295 mm) minimum provided that car doors provide a clear opening 36 inches (915 mm) wide minimum. 2. Existing elevator cars shall be permitted to provide a clear width 36 inches (915 mm) minimum, clear depth 54 inches (1370 mm) minimum, and a net clear platform area 15 square feet (1.4 m2) minimum. 408.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303. 408.4.3 Platform to Hoist-way Clearance. The platform to hoist-way clearance shall comply with 407.4.3. 408.4.4 Leveling. Elevator car leveling shall comply with 407.4.4. 408.4.5 Illumination. Elevator car illumination shall comply with 407.4.5. 408.4.6 Car Controls. Elevator car controls shall comply with 407.4.6. Control panels shall be centered on a side wall. 408.4.7 Designations and Indicators of Car Controls. Designations and indicators of car controls shall comply with 407.4.7. 408.4.8 Emergency Communications. Car emergency signaling devices complying with 407.4.9 shall be provided. 409 Private Residence Elevators 409.1 General. Private residence elevators that are provided within a residential dwelling unit required to provide mobility features complying with 809.2 through 809.4 shall comply with 409 and with ASME A17.1 (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1). They shall be PO 00000 Frm 00058 Fmt 4701 Sfmt 4700 passenger elevators as classified by ASME A17.1. Elevator operation shall be automatic. 409.2 Call Buttons. Call buttons shall be 3⁄4 inch (19 mm) minimum in the smallest dimension and shall comply with 309. 409.3 Elevator Doors. Hoist-way doors, car doors, and car gates shall comply with 409.3 and 404. EXCEPTION: Doors shall not be required to comply with the maneuvering clearance requirements in 404.2.4.1 for approaches to the push side of swinging doors. 409.3.1 Power Operation. Elevator car and hoist-way doors and gates shall be power operated and shall comply with ANSI/BHMA A156.19 (1997 or 2002 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1). Power operated doors and gates shall remain open for 20 seconds minimum when activated. EXCEPTION: In elevator cars with more than one opening, hoist-way doors and gates shall be permitted to be of the manual-open, self-close type. 409.3.2 Location. Elevator car doors or gates shall be positioned at the narrow end of the clear floor spaces required by 409.4.1. 409.4 Elevator Cars. Private residence elevator cars shall comply with 409.4. 409.4.1 Inside Dimensions of Elevator Cars. Elevator cars shall provide a clear floor space of 36 inches (915 mm) minimum by 48 inches (1220 mm) minimum and shall comply with 305. 409.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303. 409.4.3 Platform to Hoist-way Clearance. The clearance between the car platform and the edge of any landing sill shall be 11⁄2 inch (38 mm) maximum. 409.4.4 Leveling. Each car shall automatically stop at a floor landing within a tolerance of 1⁄2 inch (13 mm) under rated loading to zero loading conditions. 409.4.5 Illumination Levels. Elevator car illumination shall comply with 407.4.5. 409.4.6 Car Controls. Elevator car control buttons shall comply with 409.4.6, 309.3, 309.4, and shall be raised or flush. 409.4.6.1 Size. Control buttons shall be 3⁄4 inch (19 mm) minimum in their smallest dimension. 409.4.6.2 Location. Control panels shall be on a side wall, 12 inches (305 mm) minimum from any adjacent wall. 409.4.7 Emergency Communications. Emergency two-way communication systems shall comply with 409.4.7. 409.4.7.1 Type. A telephone and emergency signal device shall be provided in the car. 409.4.7.2 Operable Parts. The telephone and emergency signaling device shall comply with 309.3 and 309.4. 409.4.7.3 Compartment. If the telephone or device is in a closed compartment, the compartment door hardware shall comply with 309. 409.4.7.4 Cord. The telephone cord shall be 29 inches (735 mm) long minimum. 410 Platform Lifts 410.1 General. Platform lifts shall comply with ASME A18.1 (1999 edition or 2003 edition) (incorporated by reference, see Referenced Standards’’ in Chapter 1). E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations Platform lifts shall not be attendant operated and shall provide unassisted entry and exit from the lift. 410.2 Floor Surfaces. Floor surfaces in platform lifts shall comply with 302 and 303. 410.3 Clear Floor Space. Clear floor space in platform lifts shall comply with 305. 410.4 Platform to Runway Clearance. The clearance between the platform sill and the edge of any runway landing shall be 11⁄4 inch (32 mm) maximum. 410.5 Operable Parts. Controls for platform lifts shall comply with 309. 410.6 Doors and Gates. Platform lifts shall have low-energy power operated doors or gates complying with 404.3. Doors shall remain open for 20 seconds minimum. End doors and gates shall provide a clear width 32 inches (815 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1065 mm) minimum. EXCEPTION: Platform lifts serving two landings maximum and having doors or gates on opposite sides shall be permitted to have self-closing manual doors or gates. 502.4 Floor or Ground Surfaces. Parking spaces and access aisles serving them shall comply with 302. Access aisles shall be at the same level as the parking spaces they serve. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted. 502.5 Vertical Clearance. Parking spaces for vans and access aisles and vehicular routes serving them shall provide a vertical clearance of 98 inches (2490 mm) minimum. 502.6 Identification. Parking space identification signs shall include the International Symbol of Accessibility complying with 703.7.2.1. Signs identifying van parking spaces shall contain the designation ‘‘van accessible.’’ Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign. 502.7 Relationship to Accessible Routes. Parking spaces and access aisles shall be designed so that cars and vans, when parked, cannot obstruct the required clear width of adjacent accessible routes. Chapter 5: General Site and Building Elements 503 Passenger Loading Zones 503.1 General. Passenger loading zones shall comply with 503. 503.2 Vehicle Pull-Up Space. Passenger loading zones shall provide a vehicular pullup space 96 inches (2440 mm) wide minimum and 20 feet (6100 mm) long minimum. 503.3 Access Aisle. Passenger loading zones shall provide access aisles complying with 503 adjacent to the vehicle pull-up space. Access aisles shall adjoin an accessible route and shall not overlap the vehicular way. 503.3.1 Width. Access aisles serving vehicle pull-up spaces shall be 60 inches (1525 mm) wide minimum. 503.3.2 Length. Access aisles shall extend the full length of the vehicle pull-up spaces they serve. 503.3.3 Marking. Access aisles shall be marked so as to discourage parking in them. 503.4 Floor and Ground Surfaces. Vehicle pull-up spaces and access aisles serving them shall comply with 302. Access aisles shall be at the same level as the vehicle pull-up space they serve. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted. 503.5 Vertical Clearance. Vehicle pull-up spaces, access aisles serving them, and a vehicular route from an entrance to the passenger loading zone, and from the passenger loading zone to a vehicular exit shall provide a vertical clearance of 114 inches (2895 mm) minimum. emcdonald on DSK67QTVN1PROD with RULES2 501 General 501.1 Scope. The provisions of Chapter 5 shall apply where required by Chapter 2 or where referenced by a requirement in this document. 502 Parking Spaces 502.1 General. Car and van parking spaces shall comply with 502. Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings. EXCEPTION: Where parking spaces or access aisles are not adjacent to another parking space or access aisle, measurements shall be permitted to include the full width of the line defining the parking space or access aisle. 502.2 Vehicle Spaces. Car parking spaces shall be 96 inches (2440 mm) wide minimum and van parking spaces shall be 132 inches (3350 mm) wide minimum, shall be marked to define the width, and shall have an adjacent access aisle complying with 502.3. EXCEPTION: Van parking spaces shall be permitted to be 96 inches (2440 mm) wide minimum where the access aisle is 96 inches (2440 mm) wide minimum. 502.3 Access Aisle. Access aisles serving parking spaces shall comply with 502.3. Access aisles shall adjoin an accessible route. Two parking spaces shall be permitted to share a common access aisle. 502.3.1 Width. Access aisles serving car and van parking spaces shall be 60 inches (1525 mm) wide minimum. 502.3.2 Length. Access aisles shall extend the full length of the parking spaces they serve. 502.3.3 Marking. Access aisles shall be marked so as to discourage parking in them. 502.3.4 Location. Access aisles shall not overlap the vehicular way. Access aisles shall be permitted to be placed on either side of the parking space except for angled van parking spaces which shall have access aisles located on the passenger side of the parking spaces. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 504 Stairways 504.1 General. Stairs shall comply with 504. 504.2 Treads and Risers. All steps on a flight of stairs shall have uniform riser heights and uniform tread depths. Risers shall be 4 inches (100 mm) high minimum and 7 inches (180 mm) high maximum. Treads shall be 11 inches (280 mm) deep minimum. 504.3 Open Risers. Open risers are not permitted. PO 00000 Frm 00059 Fmt 4701 Sfmt 4700 59533 504.4 Tread Surface. Stair treads shall comply with 302. Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. 504.5 Nosings. The radius of curvature at the leading edge of the tread shall be 1⁄2 inch (13 mm) maximum. Nosings that project beyond risers shall have the underside of the leading edge curved or beveled. Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical. The permitted projection of the nosing shall extend 11⁄2 inches (38 mm) maximum over the tread below. 504.6 Handrails. Stairs shall have handrails complying with 505. 504.7 Wet Conditions. Stair treads and landings subject to wet conditions shall be designed to prevent the accumulation of water. 505 Handrails 505.1 General. Handrails provided along walking surfaces complying with 403, required at ramps complying with 405, and required at stairs complying with 504 shall comply with 505. 505.2 Where Required. Handrails shall be provided on both sides of stairs and ramps. EXCEPTION: In assembly areas, handrails shall not be required on both sides of aisle ramps where a handrail is provided at either side or within the aisle width. 505.3 Continuity. Handrails shall be continuous within the full length of each stair flight or ramp run. Inside handrails on switchback or dogleg stairs and ramps shall be continuous between flights or runs. EXCEPTION: In assembly areas, handrails on ramps shall not be required to be continuous in aisles serving seating. 505.4 Height. Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces. Handrails shall be at a consistent height above walking surfaces, stair nosings, and ramp surfaces. 505.5 Clearance. Clearance between handrail gripping surfaces and adjacent surfaces shall be 11⁄2 inches (38 mm) minimum. 505.6 Gripping Surface. Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of handrail gripping surfaces shall not be obstructed for more than 20 percent of their length. Where provided, horizontal projections shall occur 11⁄2 inches (38 mm) minimum below the bottom of the handrail gripping surface. EXCEPTIONS: 1. Where handrails are provided along walking surfaces with slopes not steeper than 1:20, the bottoms of handrail gripping surfaces shall be permitted to be obstructed along their entire length where they are integral to crash rails or bumper guards. 2. The distance between horizontal projections and the bottom of the gripping surface shall be permitted to be reduced by 1/8 inch (3.2 mm) for each 1⁄2 inch (13 mm) of additional handrail perimeter dimension that exceeds 4 inches (100 mm). E:\FR\FM\26SER2.SGM 26SER2 59534 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 505.7 Cross Section. Handrail gripping surfaces shall have a cross section complying with 505.7.1 or 505.7.2. 505.7.1 Circular Cross Section. Handrail gripping surfaces with a circular cross section shall have an outside diameter of 11⁄4 inches (32 mm) minimum and 2 inches (51 mm) maximum. 505.7.2 Non-Circular Cross Sections. Handrail gripping surfaces with a noncircular cross section shall have a perimeter dimension of 4 inches (100 mm) minimum and 61⁄4 inches (160 mm) maximum, and a cross-section dimension of 21⁄4 inches (57 mm) maximum. 505.8 Surfaces. Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges. 505.9 Fittings. Handrails shall not rotate within their fittings. 505.10 Handrail Extensions. Handrail gripping surfaces shall extend beyond and in the same direction of stair flights and ramp runs in accordance with 505.10. EXCEPTIONS: 1. Extensions shall not be required for continuous handrails at the inside turn of switchback or dogleg stairs and ramps. 2. In assembly areas, extensions shall not be required for ramp handrails in aisles serving seating where the handrails are discontinuous to provide access to seating and to permit crossovers within aisles. 3. In alterations, full extensions of handrails shall not be required where such extensions would be hazardous due to plan configuration. 505.10.1 Top and Bottom Extension at Ramps. Ramp handrails shall extend horizontally above the landing for 12 inches (305 mm) minimum beyond the top and bottom of ramp runs. Extensions shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent ramp run. 505.10.2 Top Extension at Stairs. At the top of a stair flight, handrails shall extend horizontally above the landing for 12 inches (305 mm) minimum beginning directly above the first riser nosing. Extensions shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent stair flight. 505.10.3 Bottom Extension at Stairs. At the bottom of a stair flight, handrails shall extend at the slope of the stair flight for a horizontal distance at least equal to one tread depth beyond the last riser nosing. Extension shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent stair flight. emcdonald on DSK67QTVN1PROD with RULES2 CHAPTER 6: PLUMBING ELEMENTS AND FACILITIES 601 General 601.1 Scope. The provisions of Chapter 6 shall apply where required by Chapter 2 or where referenced by a requirement in this document. 602 Drinking Fountains 602.1 General. Drinking fountains shall comply with 307 and 602. 602.2 Clear Floor Space. Units shall have a clear floor or ground space complying with VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 305 positioned for a forward approach and centered on the unit. Knee and toe clearance complying with 306 shall be provided. EXCEPTION: A parallel approach complying with 305 shall be permitted at units for children’s use where the spout is 30 inches (760 mm) maximum above the finish floor or ground and is 31⁄2 inches (90 mm) maximum from the front edge of the unit, including bumpers. 602.3 Operable Parts. Operable parts shall comply with 309. 602.4 Spout Height. Spout outlets shall be 36 inches (915 mm) maximum above the finish floor or ground. 602.5 Spout Location. The spout shall be located 15 inches (380 mm) minimum from the vertical support and 5 inches (125 mm) maximum from the front edge of the unit, including bumpers. 602.6 Water Flow. The spout shall provide a flow of water 4 inches (100 mm) high minimum and shall be located 5 inches (125 mm) maximum from the front of the unit. The angle of the water stream shall be measured horizontally relative to the front face of the unit. Where spouts are located less than 3 inches (75 mm) of the front of the unit, the angle of the water stream shall be 30 degrees maximum. Where spouts are located between 3 inches (75 mm) and 5 inches (125 mm) maximum from the front of the unit, the angle of the water stream shall be 15 degrees maximum. 602.7 Drinking Fountains for Standing Persons. Spout outlets of drinking fountains for standing persons shall be 38 inches (965 mm) minimum and 43 inches (1090 mm) maximum above the finish floor or ground. 603 Toilet and Bathing Rooms 603.1 General. Toilet and bathing rooms shall comply with 603. 603.2 Clearances. Clearances shall comply with 603.2. 603.2.1 Turning Space. Turning space complying with 304 shall be provided within the room. 603.2.2 Overlap. Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap. 603.2.3 Door Swing. Doors shall not swing into the clear floor space or clearance required for any fixture. Doors shall be permitted to swing into the required turning space. EXCEPTIONS: 1. Doors to a toilet room or bathing room for a single occupant accessed only through a private office and not for common use or public use shall be permitted to swing into the clear floor space or clearance provided the swing of the door can be reversed to comply with 603.2.3. 2. Where the toilet room or bathing room is for individual use and a clear floor space complying with 305.3 is provided within the room beyond the arc of the door swing, doors shall be permitted to swing into the clear floor space or clearance required for any fixture. 603.3 Mirrors. Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1015 mm) maximum above the finish floor or ground. Mirrors not located above lavatories or countertops shall be PO 00000 Frm 00060 Fmt 4701 Sfmt 4700 installed with the bottom edge of the reflecting surface 35 inches (890 mm) maximum above the finish floor or ground. 603.4 Coat Hooks and Shelves. Coat hooks shall be located within one of the reach ranges specified in 308. Shelves shall be located 40 inches (1015 mm) minimum and 48 inches (1220 mm) maximum above the finish floor. 604 Water Closets and Toilet Compartments 604.1 General. Water closets and toilet compartments shall comply with 604.2 through 604.8. EXCEPTION: Water closets and toilet compartments for children’s use shall be permitted to comply with 604.9. 604.2 Location. The water closet shall be positioned with a wall or partition to the rear and to one side. The centerline of the water closet shall be 16 inches (405 mm) minimum to 18 inches (455 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum from the side wall or partition in the ambulatory accessible toilet compartment specified in 604.8.2. Water closets shall be arranged for a left-hand or right-hand approach. 604.3 Clearance. Clearances around water closets and in toilet compartments shall comply with 604.3. 604.3.1 Size. Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall. 604.3.2 Overlap. The required clearance around the water closet shall be permitted to overlap the water closet, associated grab bars, dispensers, sanitary napkin disposal units, coat hooks, shelves, accessible routes, clear floor space and clearances required at other fixtures, and the turning space. No other fixtures or obstructions shall be located within the required water closet clearance. EXCEPTION: In residential dwelling units, a lavatory complying with 606 shall be permitted on the rear wall 18 inches (455 mm) minimum from the water closet centerline where the clearance at the water closet is 66 inches (1675 mm) minimum measured perpendicular from the rear wall. 604.4 Seats. The seat height of a water closet above the finish floor shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured to the top of the seat. Seats shall not be sprung to return to a lifted position. EXCEPTIONS: 1. A water closet in a toilet room for a single occupant accessed only through a private office and not for common use or public use shall not be required to comply with 604.4. 2. In residential dwelling units, the height of water closets shall be permitted to be 15 inches (380 mm) minimum and 19 inches (485 mm) maximum above the finish floor measured to the top of the seat. 604.5 Grab Bars. Grab bars for water closets shall comply with 609. Grab bars shall be provided on the side wall closest to the water closet and on the rear wall. EXCEPTIONS: 1. Grab bars shall not be required to be installed in a toilet room for E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations a single occupant accessed only through a private office and not for common use or public use provided that reinforcement has been installed in walls and located so as to permit the installation of grab bars complying with 604.5. 2. In residential dwelling units, grab bars shall not be required to be installed in toilet or bathrooms provided that reinforcement has been installed in walls and located so as to permit the installation of grab bars complying with 604.5. 3. In detention or correction facilities, grab bars shall not be required to be installed in housing or holding cells that are specially designed without protrusions for purposes of suicide prevention. 604.5.1 Side Wall. The side wall grab bar shall be 42 inches (1065 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1370 mm) minimum from the rear wall. 604.5.2 Rear Wall. The rear wall grab bar shall be 36 inches (915 mm) long minimum and extend from the centerline of the water closet 12 inches (305 mm) minimum on one side and 24 inches (610 mm) minimum on the other side. EXCEPTIONS: 1. The rear grab bar shall be permitted to be 24 inches (610 mm) long minimum, centered on the water closet, where wall space does not permit a length of 36 inches (915 mm) minimum due to the location of a recessed fixture adjacent to the water closet. 2. Where an administrative authority requires flush controls for flush valves to be located in a position that conflicts with the location of the rear grab bar, then the rear grab bar shall be permitted to be split or shifted to the open side of the toilet area. 604.6 Flush Controls. Flush controls shall be hand operated or automatic. Hand operated flush controls shall comply with 309. Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with 604.8.2. 604.7 Dispensers. Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser. The outlet of the dispenser shall be 15 inches (380 mm) minimum and 48 inches (1220 mm) maximum above the finish floor and shall not be located behind grab bars. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow. 604.8 Toilet Compartments. Wheelchair accessible toilet compartments shall meet the requirements of 604.8.1 and 604.8.3. Compartments containing more than one plumbing fixture shall comply with 603. Ambulatory accessible compartments shall comply with 604.8.2 and 604.8.3. 604.8.1 Wheelchair Accessible Compartments. Wheelchair accessible compartments shall comply with 604.8.1. 604.8.1.1 Size. Wheelchair accessible compartments shall be 60 inches (1525 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1420 mm) deep minimum for wall hung water closets and 59 inches (1500 mm) deep minimum for floor VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 mounted water closets measured perpendicular to the rear wall. Wheelchair accessible compartments for children’s use shall be 60 inches (1525 mm) wide minimum measured perpendicular to the side wall, and 59 inches (1500 mm) deep minimum for wall hung and floor mounted water closets measured perpendicular to the rear wall. 604.8.1.2 Doors. Toilet compartment doors, including door hardware, shall comply with 404 except that if the approach is to the latch side of the compartment door, clearance between the door side of the compartment and any obstruction shall be 42 inches (1065 mm) minimum. Doors shall be located in the front partition or in the side wall or partition farthest from the water closet. Where located in the front partition, the door opening shall be 4 inches (100 mm) maximum from the side wall or partition farthest from the water closet. Where located in the side wall or partition, the door opening shall be 4 inches (100 mm) maximum from the front partition. The door shall be selfclosing. A door pull complying with 404.2.7 shall be placed on both sides of the door near the latch. Toilet compartment doors shall not swing into the minimum required compartment area. 604.8.1.3 Approach. Compartments shall be arranged for left-hand or right-hand approach to the water closet. 604.8.1.4 Toe Clearance. The front partition and at least one side partition shall provide a toe clearance of 9 inches (230 mm) minimum above the finish floor and 6 inches (150 mm) deep minimum beyond the compartment-side face of the partition, exclusive of partition support members. Compartments for children’s use shall provide a toe clearance of 12 inches (305 mm) minimum above the finish floor. EXCEPTION: Toe clearance at the front partition is not required in a compartment greater than 62 inches (1575 mm) deep with a wall-hung water closet or 65 inches (1650 mm) deep with a floor-mounted water closet. Toe clearance at the side partition is not required in a compartment greater than 66 inches (1675 mm) wide. Toe clearance at the front partition is not required in a compartment for children’s use that is greater than 65 inches (1650 mm) deep. 604.8.1.5 Grab Bars. Grab bars shall comply with 609. A sidewall grab bar complying with 604.5.1 shall be provided and shall be located on the wall closest to the water closet. In addition, a rear-wall grab bar complying with 604.5.2 shall be provided. 604.8.2 Ambulatory Accessible Compartments. Ambulatory accessible compartments shall comply with 604.8.2. 604.8.2.1 Size. Ambulatory accessible compartments shall have a depth of 60 inches (1525 mm) minimum and a width of 35 inches (890 mm) minimum and 37 inches (940 mm) maximum. 604.8.2.2 Doors. Toilet compartment doors, including door hardware, shall comply with 404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the compartment and any obstruction shall be 42 inches (1065 mm) minimum. The door shall be self-closing. A door pull complying with 404.2.7 shall be placed on both sides of the PO 00000 Frm 00061 Fmt 4701 Sfmt 4700 59535 door near the latch. Toilet compartment doors shall not swing into the minimum required compartment area. 604.8.2.3 Grab Bars. Grab bars shall comply with 609. A sidewall grab bar complying with 604.5.1 shall be provided on both sides of the compartment. 604.8.3 Coat Hooks and Shelves. Coat hooks shall be located within one of the reach ranges specified in 308. Shelves shall be located 40 inches (1015 mm) minimum and 48 inches (1220 mm) maximum above the finish floor. 604.9 Water Closets and Toilet Compartments for Children’s Use. Water closets and toilet compartments for children’s use shall comply with 604.9. 604.9.1 Location. The water closet shall be located with a wall or partition to the rear and to one side. The centerline of the water closet shall be 12 inches (305 mm) minimum and 18 inches (455 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum from the side wall or partition in the ambulatory accessible toilet compartment specified in 604.8.2. Compartments shall be arranged for left-hand or right-hand approach to the water closet. 604.9.2 Clearance. Clearance around a water closet shall comply with 604.3. 604.9.3 Height. The height of water closets shall be 11 inches (280 mm) minimum and 17 inches (430 mm) maximum measured to the top of the seat. Seats shall not be sprung to return to a lifted position. 604.9.4 Grab Bars. Grab bars for water closets shall comply with 604.5. 604.9.5 Flush Controls. Flush controls shall be hand operated or automatic. Hand operated flush controls shall comply with 309.2 and 309.4 and shall be installed 36 inches (915 mm) maximum above the finish floor. Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with 604.8.2. 604.9.6 Dispensers. Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser. The outlet of the dispenser shall be 14 inches (355 mm) minimum and 19 inches (485 mm) maximum above the finish floor. There shall be a clearance of 11⁄2 inches (38 mm) minimum below the grab bar. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow. 604.9.7 Toilet Compartments. Toilet compartments shall comply with 604.8. 605 Urinals 605.1 General. Urinals shall comply with 605. 605.2 Height and Depth. Urinals shall be the stall-type or the wall-hung type with the rim 17 inches (430 mm) maximum above the finish floor or ground. Urinals shall be 131⁄2 inches (345 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture. 605.3 Clear Floor Space. A clear floor or ground space complying with 305 positioned for forward approach shall be provided. E:\FR\FM\26SER2.SGM 26SER2 59536 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 605.4 Flush Controls. Flush controls shall be hand operated or automatic. Hand operated flush controls shall comply with 309. 606 Lavatories and Sinks 606.1 General. Lavatories and sinks shall comply with 606. 606.2 Clear Floor Space. A clear floor space complying with 305, positioned for a forward approach, and knee and toe clearance complying with 306 shall be provided. EXCEPTIONS: 1. A parallel approach complying with 305 shall be permitted to a kitchen sink in a space where a cook top or conventional range is not provided and to wet bars. 2. A lavatory in a toilet room or bathing facility for a single occupant accessed only through a private office and not for common use or public use shall not be required to provide knee and toe clearance complying with 306. 3. In residential dwelling units, cabinetry shall be permitted under lavatories and kitchen sinks provided that all of the following conditions are met: (a) the cabinetry can be removed without removal or replacement of the fixture; (b) the finish floor extends under the cabinetry; and (c) the walls behind and surrounding the cabinetry are finished. 4. A knee clearance of 24 inches (610 mm) minimum above the finish floor or ground shall be permitted at lavatories and sinks used primarily by children 6 through 12 years where the rim or counter surface is 31 inches (785 mm) maximum above the finish floor or ground. 5. A parallel approach complying with 305 shall be permitted to lavatories and sinks used primarily by children 5 years and younger. 6. The dip of the overflow shall not be considered in determining knee and toe clearances. 7. No more than one bowl of a multi-bowl sink shall be required to provide knee and toe clearance complying with 306. 606.3 Height. Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (865 mm) maximum above the finish floor or ground. EXCEPTIONS: 1. A lavatory in a toilet or bathing facility for a single occupant accessed only through a private office and not for common use or public use shall not be required to comply with 606.3. 2. In residential dwelling unit kitchens, sinks that are adjustable to variable heights, 29 inches (735 mm) minimum and 36 inches (915 mm) maximum, shall be permitted where rough-in plumbing permits connections of supply and drain pipes for sinks mounted at the height of 29 inches (735 mm). 606.4 Faucets. Controls for faucets shall comply with 309. Hand-operated metering faucets shall remain open for 10 seconds minimum. 606.5 Exposed Pipes and Surfaces. Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact. There VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 shall be no sharp or abrasive surfaces under lavatories and sinks. 607 Bathtubs 607.1 General. Bathtubs shall comply with 607. 607.2 Clearance. Clearance in front of bathtubs shall extend the length of the bathtub and shall be 30 inches (760 mm) wide minimum. A lavatory complying with 606 shall be permitted at the control end of the clearance. Where a permanent seat is provided at the head end of the bathtub, the clearance shall extend 12 inches (305 mm) minimum beyond the wall at the head end of the bathtub. 607.3 Seat. A permanent seat at the head end of the bathtub or a removable in-tub seat shall be provided. Seats shall comply with 610. 607.4 Grab Bars. Grab bars for bathtubs shall comply with 609 and shall be provided in accordance with 607.4.1 or 607.4.2. EXCEPTIONS: 1. Grab bars shall not be required to be installed in a bathtub located in a bathing facility for a single occupant accessed only through a private office and not for common use or public use provided that reinforcement has been installed in walls and located so as to permit the installation of grab bars complying with 607.4. 2. In residential dwelling units, grab bars shall not be required to be installed in bathtubs located in bathing facilities provided that reinforcement has been installed in walls and located so as to permit the installation of grab bars complying with 607.4. 607.4.1 Bathtubs With Permanent Seats. For bathtubs with permanent seats, grab bars shall be provided in accordance with 607.4.1. 607.4.1.1 Back Wall. Two grab bars shall be installed on the back wall, one located in accordance with 609.4 and the other located 8 inches (205 mm) minimum and 10 inches (255 mm) maximum above the rim of the bathtub. Each grab bar shall be installed 15 inches (380 mm) maximum from the head end wall and 12 inches (305 mm) maximum from the control end wall. 607.4.1.2 Control End Wall. A grab bar 24 inches (610 mm) long minimum shall be installed on the control end wall at the front edge of the bathtub. 607.4.2 Bathtubs Without Permanent Seats. For bathtubs without permanent seats, grab bars shall comply with 607.4.2. 607.4.2.1 Back Wall. Two grab bars shall be installed on the back wall, one located in accordance with 609.4 and other located 8 inches (205 mm) minimum and 10 inches (255 mm) maximum above the rim of the bathtub. Each grab bar shall be 24 inches (610 mm) long minimum and shall be installed 24 inches (610 mm) maximum from the head end wall and 12 inches (305 mm) maximum from the control end wall. 607.4.2.2 Control End Wall. A grab bar 24 inches (610 mm) long minimum shall be installed on the control end wall at the front edge of the bathtub. 607.4.2.3 Head End Wall. A grab bar 12 inches (305 mm) long minimum shall be installed on the head end wall at the front edge of the bathtub. 607.5 Controls. Controls, other than drain stoppers, shall be located on an end wall. PO 00000 Frm 00062 Fmt 4701 Sfmt 4700 Controls shall be between the bathtub rim and grab bar, and between the open side of the bathtub and the centerline of the width of the bathtub. Controls shall comply with 309.4. 607.6 Shower Spray Unit and Water. A shower spray unit with a hose 59 inches (1500 mm) long minimum that can be used both as a fixed-position shower head and as a handheld shower shall be provided. The shower spray unit shall have an on/off control with a non-positive shut-off. If an adjustable height shower head on a vertical bar is used, the bar shall be installed so as not to obstruct the use of grab bars. Bathtub shower spray units shall deliver water that is 120 °F (49 °C) maximum. 607.7 Bathtub Enclosures. Enclosures for bathtubs shall not obstruct controls, faucets, shower and spray units or obstruct transfer from wheelchairs onto bathtub seats or into bathtubs. Enclosures on bathtubs shall not have tracks installed on the rim of the open face of the bathtub. 608 Shower Compartments 608.1 General. Shower compartments shall comply with 608. 608.2 Size and Clearances for Shower Compartments. Shower compartments shall have sizes and clearances complying with 608.2. 608.2.1 Transfer Type Shower Compartments. Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915 mm) wide minimum entry on the face of the shower compartment. Clearance of 36 inches (915 mm) wide minimum by 48 inches (1220 mm) long minimum measured from the control wall shall be provided. 608.2.2 Standard Roll-In Type Shower Compartments. Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides and shall have a 60 inches (1525 mm) wide minimum entry on the face of the shower compartment. 608.2.2.1 Clearance. A 30 inch (760 mm) wide minimum by 60 inch (1525 mm) long minimum clearance shall be provided adjacent to the open face of the shower compartment. EXCEPTION: A lavatory complying with 606 shall be permitted on one 30 inch (760 mm) wide minimum side of the clearance provided that it is not on the side of the clearance adjacent to the controls or, where provided, not the side of the clearance adjacent to the shower seat. 608.2.3 Alternate Roll-In Type Shower Compartments. Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides. A 36 inch (915 mm) wide minimum entry shall be provided at one end of the long side of the compartment. 608.3 Grab Bars. Grab bars shall comply with 609 and shall be provided in accordance with 608.3. Where multiple grab bars are used, required horizontal grab bars shall be E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations installed at the same height above the finish floor. EXCEPTIONS: 1. Grab bars shall not be required to be installed in a shower located in a bathing facility for a single occupant accessed only through a private office, and not for common use or public use provided that reinforcement has been installed in walls and located so as to permit the installation of grab bars complying with 608.3. 2. In residential dwelling units, grab bars shall not be required to be installed in showers located in bathing facilities provided that reinforcement has been installed in walls and located so as to permit the installation of grab bars complying with 608.3. 608.3.1 Transfer Type Shower Compartments. In transfer type compartments, grab bars shall be provided across the control wall and back wall to a point 18 inches (455 mm) from the control wall. 608.3.2 Standard Roll-In Type Shower Compartments. Where a seat is provided in standard roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall opposite the seat. Grab bars shall not be provided above the seat. Where a seat is not provided in standard roll-in type shower compartments, grab bars shall be provided on three walls. Grab bars shall be installed 6 inches (150 mm) maximum from adjacent walls. 608.3.3 Alternate Roll-In Type Shower Compartments. In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry. Grab bars shall not be provided above the seat. Grab bars shall be installed 6 inches (150 mm) maximum from adjacent walls. 608.4 Seats. A folding or non-folding seat shall be provided in transfer type shower compartments. A folding seat shall be provided in roll-in type showers required in transient lodging guest rooms with mobility features complying with 806.2. Seats shall comply with 610. EXCEPTION: In residential dwelling units, seats shall not be required in transfer type shower compartments provided that reinforcement has been installed in walls so as to permit the installation of seats complying with 608.4. 608.5 Controls. Controls, faucets, and shower spray units shall comply with 309.4. 608.5.1 Transfer Type Shower Compartments. In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1220 mm) maximum above the shower floor and shall be located on the control wall 15 inches (380 mm) maximum from the centerline of the seat toward the shower opening. 608.5.2 Standard Roll-In Type Shower Compartments. In standard roll-in type shower compartments, the controls, faucets, and shower spray unit shall be located above the grab bar, but no higher than 48 inches (1220 mm) above the shower floor. Where a seat is provided, the controls, faucets, and shower spray unit shall be installed on the back wall adjacent to the seat wall and shall be located 27 inches (685 mm) maximum from the seat wall. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 608.5.3 Alternate Roll-In Type Shower Compartments. In alternate roll-in type shower compartments, the controls, faucets, and shower spray unit shall be located above the grab bar, but no higher than 48 inches (1220 mm) above the shower floor. Where a seat is provided, the controls, faucets, and shower spray unit shall be located on the side wall adjacent to the seat 27 inches (685 mm) maximum from the side wall behind the seat or shall be located on the back wall opposite the seat 15 inches (380 mm) maximum, left or right, of the centerline of the seat. Where a seat is not provided, the controls, faucets, and shower spray unit shall be installed on the side wall farthest from the compartment entry. 608.6 Shower Spray Unit and Water. A shower spray unit with a hose 59 inches (1500 mm) long minimum that can be used both as a fixed-position shower head and as a handheld shower shall be provided. The shower spray unit shall have an on/off control with a non-positive shut-off. If an adjustable-height shower head on a vertical bar is used, the bar shall be installed so as not to obstruct the use of grab bars. Shower spray units shall deliver water that is 120 °F (49 °C) maximum. EXCEPTION: A fixed shower head located at 48 inches (1220 mm) maximum above the shower finish floor shall be permitted instead of a hand-held spray unit in facilities that are not medical care facilities, long-term care facilities, transient lodging guest rooms, or residential dwelling units. 608.7 Thresholds. Thresholds in roll-in type shower compartments shall be 1⁄2 inch (13 mm) high maximum in accordance with 303. In transfer type shower compartments, thresholds 1⁄2 inch (13 mm) high maximum shall be beveled, rounded, or vertical. EXCEPTION: A threshold 2 inches (51 mm) high maximum shall be permitted in transfer type shower compartments in existing facilities where provision of a 1⁄2 inch (13 mm) high threshold would disturb the structural reinforcement of the floor slab. 608.8 Shower Enclosures. Enclosures for shower compartments shall not obstruct controls, faucets, and shower spray units or obstruct transfer from wheelchairs onto shower seats. 609 Grab Bars 609.1 General. Grab bars in toilet facilities and bathing facilities shall comply with 609. 609.2 Cross Section. Grab bars shall have a cross section complying with 609.2.1 or 609.2.2. 609.2.1 Circular Cross Section. Grab bars with circular cross sections shall have an outside diameter of 11⁄4 inches (32 mm) minimum and 2 inches (51 mm) maximum. 609.2.2 Non-Circular Cross Section. Grab bars with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8 inches (120 mm) maximum. 609.3 Spacing. The space between the wall and the grab bar shall be 11⁄2 inches (38 mm). The space between the grab bar and projecting objects below and at the ends shall be 11⁄2 inches (38 mm) minimum. The space PO 00000 Frm 00063 Fmt 4701 Sfmt 4700 59537 between the grab bar and projecting objects above shall be 12 inches (305 mm) minimum. EXCEPTION: The space between the grab bars and shower controls, shower fittings, and other grab bars above shall be permitted to be 11⁄2 inches (38 mm) minimum. 609.4 Position of Grab Bars. Grab bars shall be installed in a horizontal position, 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor measured to the top of the gripping surface, except that at water closets for children’s use complying with 604.9, grab bars shall be installed in a horizontal position 18 inches (455 mm) minimum and 27 inches (685 mm) maximum above the finish floor measured to the top of the gripping surface. The height of the lower grab bar on the back wall of a bathtub shall comply with 607.4.1.1 or 607.4.2.1. 609.5 Surface Hazards. Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges. 609.6 Fittings. Grab bars shall not rotate within their fittings. 609.7 Installation. Grab bars shall be installed in any manner that provides a gripping surface at the specified locations and that does not obstruct the required clear floor space. 609.8 Structural Strength. Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the grab bar, fastener, mounting device, or supporting structure. 610 Seats 610.1 General. Seats in bathtubs and shower compartments shall comply with 610. 610.2 Bathtub Seats. The top of bathtub seats shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor. The depth of a removable in-tub seat shall be 15 inches (380 mm) minimum and 16 inches (405 mm) maximum. The seat shall be capable of secure placement. Permanent seats at the head end of the bathtub shall be 15 inches (380 mm) deep minimum and shall extend from the back wall to or beyond the outer edge of the bathtub. 610.3 Shower Compartment Seats. Where a seat is provided in a standard roll-in shower compartment, it shall be a folding type, shall be installed on the side wall adjacent to the controls, and shall extend from the back wall to a point within 3 inches (75 mm) of the compartment entry. Where a seat is provided in an alternate roll-in type shower compartment, it shall be a folding type, shall be installed on the front wall opposite the back wall, and shall extend from the adjacent side wall to a point within 3 inches (75 mm) of the compartment entry. In transfer-type showers, the seat shall extend from the back wall to a point within 3 inches (75 mm) of the compartment entry. The top of the seat shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor. Seats shall comply with 610.3.1 or 610.3.2. 610.3.1 Rectangular Seats. The rear edge of a rectangular seat shall be 21⁄2 inches (64 mm) maximum and the front edge 15 inches E:\FR\FM\26SER2.SGM 26SER2 59538 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall. The side edge of the seat shall be 11⁄2 inches (38 mm) maximum from the adjacent wall. 610.3.2 L-Shaped Seats. The rear edge of an L-shaped seat shall be 21⁄2 inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall. The rear edge of the ‘‘L’’ portion of the seat shall be 11⁄2 inches (38 mm) maximum from the wall and the front edge shall be 14 inches (355 mm) minimum and 15 inches (380 mm) maximum from the wall. The end of the ‘‘L’’ shall be 22 inches (560 mm) minimum and 23 inches maximum (585 mm) from the main seat wall. 610.4 Structural Strength. Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure. 611 Washing Machines and Clothes Dryers 611.1 General. Washing machines and clothes dryers shall comply with 611. 611.2 Clear Floor Space. A clear floor or ground space complying with 305 positioned for parallel approach shall be provided. The clear floor or ground space shall be centered on the appliance. 611.3 Operable Parts. Operable parts, including doors, lint screens, and detergent and bleach compartments shall comply with 309. 611.4 Height. Top loading machines shall have the door to the laundry compartment located 36 inches (915 mm) maximum above the finish floor. Front loading machines shall have the bottom of the opening to the laundry compartment located 15 inches (380 mm) minimum and 36 inches (915 mm) maximum above the finish floor. 612 Saunas and Steam Rooms 612.1 General. Saunas and steam rooms shall comply with 612. 612.2 Bench. Where seating is provided in saunas and steam rooms, at least one bench shall comply with 903. Doors shall not swing into the clear floor space required by 903.2. EXCEPTION: A readily removable bench shall be permitted to obstruct the turning space required by 612.3 and the clear floor or ground space required by 903.2. 612.3 Turning Space. A turning space complying with 304 shall be provided within saunas and steam rooms. Chapter 7: Communication Elements and Features emcdonald on DSK67QTVN1PROD with RULES2 701 General 701.1 Scope. The provisions of Chapter 7 shall apply where required by Chapter 2 or where referenced by a requirement in this document. 702 Fire Alarm Systems 702.1 General. Fire alarm systems shall have permanently installed audible and visible alarms complying with NFPA 72 (1999 or 2002 edition) (incorporated by reference, see Referenced Standards’’ in Chapter 1), except that the maximum allowable sound level of audible notification VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 appliances complying with section 4–3.2.1 of NFPA 72 (1999 edition) shall have a sound level no more than 110 dB at the minimum hearing distance from the audible appliance. In addition, alarms in guest rooms required to provide communication features shall comply with sections 4–3 and 4–4 of NFPA 72 (1999 edition) or sections 7.4 and 7.5 of NFPA 72 (2002 edition). EXCEPTION: Fire alarm systems in medical care facilities shall be permitted to be provided in accordance with industry practice. percent minimum and 170 percent maximum of the raised character height. 703.3 Braille. Braille shall be contracted (Grade 2) and shall comply with 703.3 and 703.4. 703.3.1 Dimensions and Capitalization. Braille dots shall have a domed or rounded shape and shall comply with Table 703.3.1. The indication of an uppercase letter or letters shall only be used before the first word of sentences, proper nouns and names, individual letters of the alphabet, initials, and acronyms. 703 Signs 703.1 General. Signs shall comply with 703. Where both visual and tactile characters are required, either one sign with both visual and tactile characters, or two separate signs, one with visual, and one with tactile characters, shall be provided. 703.2 Raised Characters. Raised characters shall comply with 703.2 and shall be duplicated in braille complying with 703.3. Raised characters shall be installed in accordance with 703.4. 703.2.1 Depth. Raised characters shall be 1⁄32 inch (0.8 mm) minimum above their background. 703.2.2 Case. Characters shall be uppercase. 703.2.3 Style. Characters shall be sans serif. Characters shall not be italic, oblique, script, highly decorative, or of other unusual forms. 703.2.4 Character Proportions. Characters shall be selected from fonts where the width of the uppercase letter ‘‘O’’ is 55 percent minimum and 110 percent maximum of the height of the uppercase letter ‘‘I’’. 703.2.5 Character Height. Character height measured vertically from the baseline of the character shall be 5⁄8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter ‘‘I’’. EXCEPTION: Where separate raised and visual characters with the same information are provided, raised character height shall be permitted to be 1⁄2 inch (13 mm) minimum. 703.2.6 Stroke Thickness. Stroke thickness of the uppercase letter ‘‘I’’ shall be 15 percent maximum of the height of the character. 703.2.7 Character Spacing. Character spacing shall be measured between the two closest points of adjacent raised characters within a message, excluding word spaces. Where characters have rectangular cross sections, spacing between individual raised characters shall be 1⁄8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum. Where characters have other cross sections, spacing between individual raised characters shall be 1⁄16 inch (1.6 mm) minimum and 4 times the raised character stroke width maximum at the base of the cross sections, and 1⁄8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum at the top of the cross sections. Characters shall be separated from raised borders and decorative elements 3⁄8 inch (9.5 mm) minimum. 703.2.8 Line Spacing. Spacing between the baselines of separate lines of raised characters within a message shall be 135 TABLE 703.3.1—BRAILLE DIMENSIONS PO 00000 Frm 00064 Fmt 4701 Sfmt 4700 Measurement range Dot base diameter ........ Distance between two dots in the same cell 1. Distance between corresponding dots in adjacent cells 1. Dot height ..................... Distance between corresponding dots from one cell directly below 1. 1 Measured Minimum in inches Maximum in inches 0.059 (1.5 mm) to 0.063 (1.6 mm). 0.090 (2.3 mm) to 0.100 (2.5 mm). 0.241 (6.1 mm) to 0.300 (7.6 mm). 0.025 (0.6 mm) to 0.037 (0.9 mm). 0.395 (10 mm) to 0.400 (10.2 mm). center to center. 703.3.2 Position. Braille shall be positioned below the corresponding text. If text is multi-lined, braille shall be placed below the entire text. Braille shall be separated 3⁄8 inch (9.5 mm) minimum from any other tactile characters and 3⁄8 inch (9.5 mm) minimum from raised borders and decorative elements. EXCEPTION: Braille provided on elevator car controls shall be separated 3⁄16 inch (4.8 mm) minimum and shall be located either directly below or adjacent to the corresponding raised characters or symbols. 703.4 Installation Height and Location. Signs with tactile characters shall comply with 703.4. 703.4.1 Height Above Finish Floor or Ground. Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches (1525 mm) maximum above the finish floor or ground surface, measured from the baseline of the highest tactile character. EXCEPTION: Tactile characters for elevator car controls shall not be required to comply with 703.4.1. 703.4.2 Location. Where a tactile sign is provided at a door, the sign shall be located alongside the door at the latch side. Where a tactile sign is provided at double doors with one active leaf, the sign shall be located on the inactive leaf. Where a tactile sign is provided at double doors with two active leafs, the sign shall be located to the right of the right hand door. Where there is no wall space at the latch side of a single door or at the right side of double doors, signs shall be located on the nearest adjacent wall. Signs containing tactile characters shall be located E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations so that a clear floor space of 18 inches (455 mm) minimum by 18 inches (455 mm) minimum, centered on the tactile characters, is provided beyond the arc of any door swing between the closed position and 45 degree open position. EXCEPTION: Signs with tactile characters shall be permitted on the push side of doors with closers and without hold-open devices. 703.5 Visual Characters. Visual characters shall comply with 703.5. EXCEPTION: Where visual characters comply with 703.2 and are accompanied by braille complying with 703.3, they shall not be required to comply with 703.5.2 through 703.5.9. 703.5.1 Finish and Contrast. Characters and their background shall have a non-glare finish. Characters shall contrast with their background with either light characters on a dark background or dark characters on a light background. 703.5.2 Case. Characters shall be uppercase or lowercase or a combination of both. 703.5.3 Style. Characters shall be conventional in form. Characters shall not be italic, oblique, script, highly decorative, or of other unusual forms. 59539 703.5.4 Character Proportions. Characters shall be selected from fonts where the width of the uppercase letter ‘‘O’’ is 55 percent minimum and 110 percent maximum of the height of the uppercase letter ‘‘I’’. 703.5.5 Character Height. Minimum character height shall comply with Table 703.5.5. Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign. Character height shall be based on the uppercase letter ‘‘I’’. TABLE 703.5.5—VISUAL CHARACTER HEIGHT Height to finish floor or ground from baseline of character Horizontal viewing distance Minimum character height 40 inches (1015 mm) to less than or equal to 70 inches (1780 mm). Greater than 70 inches (1780 mm) to less than or equal to 120 inches (3050 mm). less than 72 inches (1830 mm) 72 inches (1830 mm) and greater. less than 180 inches (4570 mm) ... ⁄ inch (16 mm) 5⁄8 inch (16 mm), plus 1⁄8 inch (3.2 mm) per foot (305 mm) of viewing distance above 72 inches (1830 mm). 2 inches (51 mm). 180 inches (4570 mm) and greater 2 inches (51 mm), plus 1⁄8 inch (3.2 mm) per foot (305 mm) of viewing distance above 180 inches (4570 mm). 3 inches (75 mm). 3 inches (75 mm), plus 1⁄8 inch (3.2 mm) per foot (305 mm) of viewing distance above 21 feet (6400 mm). emcdonald on DSK67QTVN1PROD with RULES2 Greater than 120 inches (3050 mm) less than 21 feet (6400 mm) ......... 21 feet (6400 mm) and greater ..... 703.5.6 Height From Finish Floor or Ground. Visual characters shall be 40 inches (1015 mm) minimum above the finish floor or ground. EXCEPTION: Visual characters indicating elevator car controls shall not be required to comply with 703.5.6. 703.5.7 Stroke Thickness. Stroke thickness of the uppercase letter ‘‘I’’ shall be 10 percent minimum and 30 percent maximum of the height of the character. 703.5.8 Character Spacing. Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces. Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height. 703.5.9 Line Spacing. Spacing between the baselines of separate lines of characters within a message shall be 135 percent minimum and 170 percent maximum of the character height. 703.6 Pictograms. Pictograms shall comply with 703.6. 703.6.1 Pictogram Field. Pictograms shall have a field height of 6 inches (150 mm) minimum. Characters and braille shall not be located in the pictogram field. 703.6.2 Finish and Contrast. Pictograms and their field shall have a non-glare finish. Pictograms shall contrast with their field with either a light pictogram on a dark field or a dark pictogram on a light field. 703.6.3 Text Descriptors. Pictograms shall have text descriptors located directly below the pictogram field. Text descriptors shall comply with 703.2, 703.3 and 703.4. 703.7 Symbols of Accessibility. Symbols of accessibility shall comply with 703.7. 703.7.1 Finish and Contrast. Symbols of accessibility and their background shall have a non-glare finish. Symbols of accessibility VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 58 shall contrast with their background with either a light symbol on a dark background or a dark symbol on a light background. 703.7.2 Symbols. 703.7.2.1 International Symbol of Accessibility. The International Symbol of Accessibility shall comply with Figure 703.7.2.1 at the end of this document. 703.7.2.2 International Symbol of TTY. The International Symbol of TTY shall comply with Figure 703.7.2.2 at the end of this document. 703.7.2.3 Volume Control Telephones. Telephones with a volume control shall be identified by a pictogram of a telephone handset with radiating sound waves. 703.7.2.4. Assistive Listening Systems. Assistive listening systems shall be identified by the International Symbol of Access for Hearing Loss complying with Figure 703.7.2.4 at the end of this document. 704 Telephones 704.1 General. Public telephones shall comply with 704. 704.2 Wheelchair Accessible Telephones. Wheelchair accessible telephones shall comply with 704.2. 704.2.1 Clear Floor or Ground Space. A clear floor or ground space complying with 305 shall be provided. The clear floor or ground space shall not be obstructed by bases, enclosures, or seats. 704.2.1.1 Parallel Approach. Where a parallel approach is provided, the distance from the edge of the telephone enclosure to the face of the telephone unit shall be 10 inches (255 mm) maximum. 704.2.1.2 Forward Approach. Where a forward approach is provided, the distance from the front edge of a counter within the telephone enclosure to the face of the PO 00000 Frm 00065 Fmt 4701 Sfmt 4700 telephone unit shall be 20 inches (510 mm) maximum. 704.2.2 Operable Parts. Operable parts shall comply with 309. Telephones shall have pushbutton controls where such service is available. 704.2.3 Telephone Directories. Telephone directories, where provided, shall be located in accordance with 309. 704.2.4 Cord Length. The cord from the telephone to the handset shall be 29 inches (735 mm) long minimum. 704.3 Volume Control Telephones. Public telephones required to have volume controls shall be equipped with a receive volume control that provides a gain adjustable up to 20 dB minimum. For incremental volume control, provide at least one intermediate step of 12 dB of gain minimum. An automatic reset shall be provided. 704.4 TTYs. TTYs required at a public pay telephone shall be permanently affixed within, or adjacent to, the telephone enclosure. Where an acoustic coupler is used, the telephone cord shall be sufficiently long to allow connection of the TTY and the telephone receiver. 704.4.1 Height. When in use, the touch surface of TTY keypads shall be 34 inches (865 mm) minimum above the finish floor. EXCEPTION: Where seats are provided, TTYs shall not be required to comply with 704.4.1. 704.5 TTY Shelf. Public pay telephones required to accommodate portable TTYs shall be equipped with a shelf and an electrical outlet within or adjacent to the telephone enclosure. The telephone handset shall be capable of being placed flush on the surface of the shelf. The shelf shall be capable of accommodating a TTY and shall have 6 inches (150 mm) minimum vertical clearance above the area where the TTY is to be placed. E:\FR\FM\26SER2.SGM 26SER2 59540 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 705 Detectable Warnings 705.1 General. Detectable warnings shall consist of a surface of truncated domes and shall comply with 705. 705.1.1 Dome Size. Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum to 65 percent of the base diameter maximum, and a height of 0.2 inch (5.1 mm). 705.1.2 Dome Spacing. Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (17 mm) minimum, measured between the most adjacent domes on a square grid. 705.1.3 Contrast. Detectable warning surfaces shall contrast visually with adjacent walking surfaces either light-on-dark, or dark-on-light. 705.2 Platform Edges. Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform. emcdonald on DSK67QTVN1PROD with RULES2 706 Assistive Listening Systems 706.1 General. Assistive listening systems required in assembly areas shall comply with 706. 706.2 Receiver Jacks. Receivers required for use with an assistive listening system shall include a 1⁄8 inch (3.2 mm) standard mono jack. 706.3 Receiver Hearing-Aid Compatibility. Receivers required to be hearing-aid compatible shall interface with telecoils in hearing aids through the provision of neckloops. 706.4 Sound Pressure Level. Assistive listening systems shall be capable of providing a sound pressure level of 110 dB minimum and 118 dB maximum with a dynamic range on the volume control of 50 dB. 706.5 Signal-to-Noise Ratio. The signalto-noise ratio for internally generated noise in assistive listening systems shall be 18 dB minimum. 706.6 Peak Clipping Level. Peak clipping shall not exceed 18 dB of clipping relative to the peaks of speech. 707 Automatic Teller Machines and Fare Machines 707.1 General. Automatic teller machines and fare machines shall comply with 707. 707.2 Clear Floor or Ground Space. A clear floor or ground space complying with 305 shall be provided. EXCEPTION: Clear floor or ground space shall not be required at drive-up only automatic teller machines and fare machines. 707.3 Operable Parts. Operable parts shall comply with 309. Unless a clear or correct key is provided, each operable part shall be able to be differentiated by sound or touch, without activation. EXCEPTION: Drive-up only automatic teller machines and fare machines shall not be required to comply with 309.2 and 309.3. 707.4 Privacy. Automatic teller machines shall provide the opportunity for the same degree of privacy of input and output available to all individuals. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 707.5 Speech Output. Machines shall be speech enabled. Operating instructions and orientation, visible transaction prompts, user input verification, error messages, and all displayed information for full use shall be accessible to and independently usable by individuals with vision impairments. Speech shall be delivered through a mechanism that is readily available to all users, including but not limited to, an industry standard connector or a telephone handset. Speech shall be recorded or digitized human, or synthesized. EXCEPTIONS: 1. Audible tones shall be permitted instead of speech for visible output that is not displayed for security purposes, including but not limited to, asterisks representing personal identification numbers. 2. Advertisements and other similar information shall not be required to be audible unless they convey information that can be used in the transaction being conducted. 3. Where speech synthesis cannot be supported, dynamic alphabetic output shall not be required to be audible. 707.5.1 User Control. Speech shall be capable of being repeated or interrupted. Volume control shall be provided for the speech function. EXCEPTION: Speech output for any single function shall be permitted to be automatically interrupted when a transaction is selected. 707.5.2 Receipts. Where receipts are provided, speech output devices shall provide audible balance inquiry information, error messages, and all other information on the printed receipt necessary to complete or verify the transaction. EXCEPTIONS: 1. Machine location, date and time of transaction, customer account number, and the machine identifier shall not be required to be audible. 2. Information on printed receipts that duplicates information available on-screen shall not be required to be presented in the form of an audible receipt. 3. Printed copies of bank statements and checks shall not be required to be audible. 707.6 Input. Input devices shall comply with 707.6. 707.6.1 Input Controls. At least one tactilely discernible input control shall be provided for each function. Where provided, key surfaces not on active areas of display screens, shall be raised above surrounding surfaces. Where membrane keys are the only method of input, each shall be tactilely discernible from surrounding surfaces and adjacent keys. 707.6.2 Numeric Keys. Numeric keys shall be arranged in a 12-key ascending or descending telephone keypad layout. The number five key shall be tactilely distinct from the other keys. 707.6.3 Function Keys. Function keys shall comply with 707.6.3. 707.6.3.1 Contrast. Function keys shall contrast visually from background surfaces. Characters and symbols on key surfaces shall contrast visually from key surfaces. Visual contrast shall be either light-on-dark or darkon-light. EXCEPTION: Tactile symbols required by 707.6.3.2 shall not be required to comply with 707.6.3.1. PO 00000 Frm 00066 Fmt 4701 Sfmt 4700 707.6.3.2 Tactile Symbols. Function key surfaces shall have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised plus sign; Decrease Value key: raised minus sign. 707.7 Display Screen. The display screen shall comply with 707.7. EXCEPTION: Drive-up only automatic teller machines and fare machines shall not be required to comply with 707.7.1. 707.7.1 Visibility. The display screen shall be visible from a point located 40 inches (1015 mm) above the center of the clear floor space in front of the machine. 707.7.2 Characters. Characters displayed on the screen shall be in a sans serif font. Characters shall be 3⁄16 inch (4.8 mm) high minimum based on the uppercase letter ‘‘I’’. Characters shall contrast with their background with either light characters on a dark background or dark characters on a light background. 707.8 Braille Instructions. Braille instructions for initiating the speech mode shall be provided. Braille shall comply with 703.3. 708 Two-Way Communication Systems 708.1 General. Two-way communication systems shall comply with 708. 708.2 Audible and Visual Indicators. The system shall provide both audible and visual signals. 708.3 Handsets. Handset cords, if provided, shall be 29 inches (735 mm) long minimum. 708.4 Residential Dwelling Unit Communication Systems. Communications systems between a residential dwelling unit and a site, building, or floor entrance shall comply with 708.4. 708.4.1 Common Use or Public Use System Interface. The common use or public use system interface shall include the capability of supporting voice and TTY communication with the residential dwelling unit interface. 708.4.2 Residential Dwelling Unit Interface. The residential dwelling unit system interface shall include a telephone jack capable of supporting voice and TTY communication with the common use or public use system interface. CHAPTER 8: SPECIAL ROOMS, SPACES, AND ELEMENTS 801 General 801.1 Scope. The provisions of Chapter 8 shall apply where required by Chapter 2 or where referenced by a requirement in this document. 802 Wheelchair Spaces, Companion Seats, and Designated Aisle Seats 802.1 Wheelchair Spaces. Wheelchair spaces shall comply with 802.1. 802.1.1 Floor or Ground Surface. The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted. 802.1.2 Width. A single wheelchair space shall be 36 inches (915 mm) wide minimum. Where two adjacent wheelchair spaces are E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations provided, each wheelchair space shall be 33 inches (840 mm) wide minimum. 802.1.3 Depth. Where a wheelchair space can be entered from the front or rear, the wheelchair space shall be 48 inches (1220 mm) deep minimum. Where a wheelchair space can be entered only from the side, the wheelchair space shall be 60 inches (1525 mm) deep minimum. 802.1.4 Approach. Wheelchair spaces shall adjoin accessible routes. Accessible routes shall not overlap wheelchair spaces. 802.1.5 Overlap. Wheelchair spaces shall not overlap circulation paths. 802.2 Lines of Sight. Lines of sight to the screen, performance area, or playing field for spectators in wheelchair spaces shall comply with 802.2. 802.2.1 Lines of Sight Over Seated Spectators. Where spectators are expected to remain seated during events, spectators in wheelchair spaces shall be afforded lines of sight complying with 802.2.1. 802.2.1.1 Lines of Sight Over Heads. Where spectators are provided lines of sight over the heads of spectators seated in the first row in front of their seats, spectators seated in wheelchair spaces shall be afforded lines of sight over the heads of seated spectators in the first row in front of wheelchair spaces. 802.2.1.2 Lines of Sight Between Heads. Where spectators are provided lines of sight over the shoulders and between the heads of spectators seated in the first row in front of their seats, spectators seated in wheelchair spaces shall be afforded lines of sight over the shoulders and between the heads of seated spectators in the first row in front of wheelchair spaces. 802.2.2 Lines of Sight Over Standing Spectators. Where spectators are expected to stand during events, spectators in wheelchair spaces shall be afforded lines of sight complying with 802.2.2. 802.2.2.1 Lines of Sight Over Heads. Where standing spectators are provided lines of sight over the heads of spectators standing in the first row in front of their seats, spectators seated in wheelchair spaces shall be afforded lines of sight over the heads of standing spectators in the first row in front of wheelchair spaces. 802.2.2.2 Lines of Sight Between Heads. Where standing spectators are provided lines of sight over the shoulders and between the heads of spectators standing in the first row in front of their seats, spectators seated in wheelchair spaces shall be afforded lines of sight over the shoulders and between the heads of standing spectators in the first row in front of wheelchair spaces. 802.3 Companion Seats. Companion seats shall comply with 802.3. 802.3.1 Alignment. In row seating, companion seats shall be located to provide shoulder alignment with adjacent wheelchair spaces. The shoulder alignment point of the wheelchair space shall be measured 36 inches (915 mm) from the front of the wheelchair space. The floor surface of the companion seat shall be at the same elevation as the floor surface of the wheelchair space. 802.3.2 Type. Companion seats shall be equivalent in size, quality, comfort, and amenities to the seating in the immediate area. Companion seats shall be permitted to be movable. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 802.4 Designated Aisle Seats. Designated aisle seats shall comply with 802.4. 802.4.1 Armrests. Where armrests are provided on the seating in the immediate area, folding or retractable armrests shall be provided on the aisle side of the seat. 802.4.2 Identification. Each designated aisle seat shall be identified by a sign or marker. 803 Dressing, Fitting, and Locker Rooms 803.1 General. Dressing, fitting, and locker rooms shall comply with 803. 803.2 Turning Space. Turning space complying with 304 shall be provided within the room. 803.3 Door Swing. Doors shall not swing into the room unless a clear floor or ground space complying with 305.3 is provided beyond the arc of the door swing. 803.4 Benches. A bench complying with 903 shall be provided within the room. 803.5 Coat Hooks and Shelves. Coat hooks provided within the room shall be located within one of the reach ranges specified in 308. Shelves shall be 40 inches (1015 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground. 804 Kitchens and Kitchenettes 804.1 General. Kitchens and kitchenettes shall comply with 804. 804.2 Clearance. Where a pass through kitchen is provided, clearances shall comply with 804.2.1. Where a U-shaped kitchen is provided, clearances shall comply with 804.2.2. EXCEPTION: Spaces that do not provide a cooktop or conventional range shall not be required to comply with 804.2. 804.2.1 Pass Through Kitchen. In pass through kitchens where counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing base cabinets, counter tops, appliances, or walls within kitchen work areas shall be 40 inches (1015 mm) minimum. Pass through kitchens shall have two entries. 804.2.2 U-Shaped. In U-shaped kitchens enclosed on three contiguous sides, clearance between all opposing base cabinets, counter tops, appliances, or walls within kitchen work areas shall be 60 inches (1525 mm) minimum. 804.3 Kitchen Work Surface. In residential dwelling units required to comply with 809, at least one 30 inches (760 mm) wide minimum section of counter shall provide a kitchen work surface that complies with 804.3. 804.3.1 Clear Floor or Ground Space. A clear floor space complying with 305 positioned for a forward approach shall be provided. The clear floor or ground space shall be centered on the kitchen work surface and shall provide knee and toe clearance complying with 306. EXCEPTION: Cabinetry shall be permitted under the kitchen work surface provided that all of the following conditions are met: (a) The cabinetry can be removed without removal or replacement of the kitchen work surface; PO 00000 Frm 00067 Fmt 4701 Sfmt 4700 59541 (b) the finish floor extends under the cabinetry; and (c) the walls behind and surrounding the cabinetry are finished. 804.3.2 Height. The kitchen work surface shall be 34 inches (865 mm) maximum above the finish floor or ground. EXCEPTION: A counter that is adjustable to provide a kitchen work surface at variable heights, 29 inches (735 mm) minimum and 36 inches (915 mm) maximum, shall be permitted. 804.3.3 Exposed Surfaces. There shall be no sharp or abrasive surfaces under the work surface counters. 804.4 Sinks. Sinks shall comply with 606. 804.5 Storage. At least 50 percent of shelf space in storage facilities shall comply with 811. 804.6 Appliances. Where provided, kitchen appliances shall comply with 804.6. 804.6.1 Clear Floor or Ground Space. A clear floor or ground space complying with 305 shall be provided at each kitchen appliance. Clear floor or ground spaces shall be permitted to overlap. 804.6.2 Operable Parts. All appliance controls shall comply with 309. EXCEPTIONS: 1. Appliance doors and door latching devices shall not be required to comply with 309.4. 2. Bottom-hinged appliance doors, when in the open position, shall not be required to comply with 309.3. 804.6.3 Dishwasher. Clear floor or ground space shall be positioned adjacent to the dishwasher door. The dishwasher door, in the open position, shall not obstruct the clear floor or ground space for the dishwasher or the sink. 804.6.4 Range or Cooktop. Where a forward approach is provided, the clear floor or ground space shall provide knee and toe clearance complying with 306. Where knee and toe space is provided, the underside of the range or cooktop shall be insulated or otherwise configured to prevent burns, abrasions, or electrical shock. The location of controls shall not require reaching across burners. 804.6.5 Oven. Ovens shall comply with 804.6.5. 804.6.5.1 Side-Hinged Door Ovens. Sidehinged door ovens shall have the work surface required by 804.3 positioned adjacent to the latch side of the oven door. 804.6.5.2 Bottom-Hinged Door Ovens. Bottom-hinged door ovens shall have the work surface required by 804.3 positioned adjacent to one side of the door. 804.6.5.3 Controls. Ovens shall have controls on front panels. 804.6.6 Refrigerator/Freezer. Combination refrigerators and freezers shall have at least 50 percent of the freezer space 54 inches (1370 mm) maximum above the finish floor or ground. The clear floor or ground space shall be positioned for a parallel approach to the space dedicated to a refrigerator/freezer with the centerline of the clear floor or ground space offset 24 inches (610 mm) maximum from the centerline of the dedicated space. E:\FR\FM\26SER2.SGM 26SER2 59542 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 805 Medical Care and Long-Term Care Facilities 805.1 General. Medical care facility and long-term care facility patient or resident sleeping rooms required to provide mobility features shall comply with 805. 805.2 Turning Space. Turning space complying with 304 shall be provided within the room. 805.3 Clear Floor or Ground Space. A clear floor space complying with 305 shall be provided on each side of the bed. The clear floor space shall be positioned for parallel approach to the side of the bed. 805.4 Toilet and Bathing Rooms. Toilet and bathing rooms that are provided as part of a patient or resident sleeping room shall comply with 603. Where provided, no fewer than one water closet, one lavatory, and one bathtub or shower shall comply with the applicable requirements of 603 through 610. 806 Transient Lodging Guest Rooms 806.1 General. Transient lodging guest rooms shall comply with 806. Guest rooms required to provide mobility features shall comply with 806.2. Guest rooms required to provide communication features shall comply with 806.3. 806.2 Guest Rooms with Mobility Features. Guest rooms required to provide mobility features shall comply with 806.2. 806.2.1 Living and Dining Areas. Living and dining areas shall be accessible. 806.2.2 Exterior Spaces. Exterior spaces, including patios, terraces and balconies, that serve the guest room shall be accessible. 806.2.3 Sleeping Areas. At least one sleeping area shall provide a clear floor space complying with 305 on both sides of a bed. The clear floor space shall be positioned for parallel approach to the side of the bed. EXCEPTION: Where a single clear floor space complying with 305 positioned for parallel approach is provided between two beds, a clear floor or ground space shall not be required on both sides of a bed. 806.2.4 Toilet and Bathing Facilities. At least one bathroom that is provided as part of a guest room shall comply with 603. No fewer than one water closet, one lavatory, and one bathtub or shower shall comply with applicable requirements of 603 through 610. In addition, required roll-in shower compartments shall comply with 608.2.2 or 608.2.3. Toilet and bathing fixtures required to comply with 603 through 610 shall be permitted to be located in more than one toilet or bathing area, provided that travel between fixtures does not require travel between other parts of the guest room. 806.2.4.1 Vanity Counter Top Space. If vanity counter top space is provided in nonaccessible guest toilet or bathing rooms, comparable vanity counter top space, in terms of size and proximity to the lavatory, shall also be provided in accessible guest toilet or bathing rooms. 806.2.5 Kitchens and Kitchenettes. Kitchens and kitchenettes shall comply with 804. 806.2.6 Turning Space. Turning space complying with 304 shall be provided within the guest room. 806.3 Guest Rooms with Communication Features. Guest rooms required to provide VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 communication features shall comply with 806.3. 806.3.1 Alarms. Where emergency warning systems are provided, alarms complying with 702 shall be provided. 806.3.2 Notification Devices. Visible notification devices shall be provided to alert room occupants of incoming telephone calls and a door knock or bell. Notification devices shall not be connected to visible alarm signal appliances. Telephones shall have volume controls compatible with the telephone system and shall comply with 704.3. Telephones shall be served by an electrical outlet complying with 309 located within 48 inches (1220 mm) of the telephone to facilitate the use of a TTY. 807 Holding Cells and Housing Cells 807.1 General. Holding cells and housing cells shall comply with 807. 807.2 Cells with Mobility Features. Cells required to provide mobility features shall comply with 807.2. 807.2.1 Turning Space. Turning space complying with 304 shall be provided within the cell. 807.2.2 Benches. Where benches are provided, at least one bench shall comply with 903. 807.2.3 Beds. Where beds are provided, clear floor space complying with 305 shall be provided on at least one side of the bed. The clear floor space shall be positioned for parallel approach to the side of the bed. 807.2.4 Toilet and Bathing Facilities. Toilet facilities or bathing facilities that are provided as part of a cell shall comply with 603. Where provided, no fewer than one water closet, one lavatory, and one bathtub or shower shall comply with the applicable requirements of 603 through 610. 807.3 Cells with Communication Features. Cells required to provide communication features shall comply with 807.3. 807.3.1 Alarms. Where audible emergency alarm systems are provided to serve the occupants of cells, visible alarms complying with 702 shall be provided. EXCEPTION: Visible alarms shall not be required where inmates or detainees are not allowed independent means of egress. 807.3.2 Telephones. Telephones, where provided within cells, shall have volume controls complying with 704.3. 808 Courtrooms 808.1 General. Courtrooms shall comply with 808. 808.2 Turning Space. Where provided, areas that are raised or depressed and accessed by ramps or platform lifts with entry ramps shall provide unobstructed turning space complying with 304. 808.3 Clear Floor Space. Each jury box and witness stand shall have, within its defined area, clear floor space complying with 305. EXCEPTION: In alterations, wheelchair spaces are not required to be located within the defined area of raised jury boxes or witness stands and shall be permitted to be located outside these spaces where ramp or platform lift access poses a hazard by restricting or projecting into a means of PO 00000 Frm 00068 Fmt 4701 Sfmt 4700 egress required by the appropriate administrative authority. 808.4 Judges’ Benches and Courtroom Stations. Judges’ benches, clerks’ stations, bailiffs’ stations, deputy clerks’ stations, court reporters’ stations and litigants’ and counsel stations shall comply with 902. 809 Residential Dwelling Units 809.1 General. Residential dwelling units shall comply with 809. Residential dwelling units required to provide mobility features shall comply with 809.2 through 809.4. Residential dwelling units required to provide communication features shall comply with 809.5. 809.2 Accessible Routes. Accessible routes complying with Chapter 4 shall be provided within residential dwelling units in accordance with 809.2. EXCEPTION: Accessible routes shall not be required to or within unfinished attics or unfinished basements. 809.2.1 Location. At least one accessible route shall connect all spaces and elements which are a part of the residential dwelling unit. Where only one accessible route is provided, it shall not pass through bathrooms, closets, or similar spaces. 809.2.2 Turning Space. All rooms served by an accessible route shall provide a turning space complying with 304. EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. 809.3 Kitchen. Where a kitchen is provided, it shall comply with 804. 809.4 Toilet Facilities and Bathing Facilities. At least one bathroom shall comply with 603. No fewer than one of each type of fixture provided shall comply with applicable requirements of 603 through 610. Toilet and bathing fixtures required to comply with 603 through 610 shall be located in the same toilet and bathing area, such that travel between fixtures does not require travel between other parts of residential dwelling unit. 809.5 Residential Dwelling Units with Communication Features. Residential dwelling units required to provide communication features shall comply with 809.5. 809.5.1 Building Fire Alarm System. Where a building fire alarm system is provided, the system wiring shall be extended to a point within the residential dwelling unit in the vicinity of the residential dwelling unit smoke detection system. 809.5.1.1 Alarm Appliances. Where alarm appliances are provided within a residential dwelling unit as part of the building fire alarm system, they shall comply with 702. 809.5.1.2 Activation. All visible alarm appliances provided within the residential dwelling unit for building fire alarm notification shall be activated upon activation of the building fire alarm in the portion of the building containing the residential dwelling unit. 809.5.2 Residential Dwelling Unit Smoke Detection System. Residential dwelling unit smoke detection systems shall comply with NFPA 72 (1999 or 2002 edition) (incorporated by reference, see Referenced Standards’’ in Chapter 1). E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 809.5.2.1 Activation. All visible alarm appliances provided within the residential dwelling unit for smoke detection notification shall be activated upon smoke detection. 809.5.3 Interconnection. The same visible alarm appliances shall be permitted to provide notification of residential dwelling unit smoke detection and building fire alarm activation. 809.5.4 Prohibited Use. Visible alarm appliances used to indicate residential dwelling unit smoke detection or building fire alarm activation shall not be used for any other purpose within the residential dwelling unit. 809.5.5 Residential Dwelling Unit Primary Entrance. Communication features shall be provided at the residential dwelling unit primary entrance complying with 809.5.5. 809.5.5.1 Notification. A hardwired electric doorbell shall be provided. A button or switch shall be provided outside the residential dwelling unit primary entrance. Activation of the button or switch shall initiate an audible tone and visible signal within the residential dwelling unit. Where visible doorbell signals are located in sleeping areas, they shall have controls to deactivate the signal. 809.5.5.2 Identification. A means for visually identifying a visitor without opening the residential dwelling unit entry door shall be provided and shall allow for a minimum 180 degree range of view. 809.5.6 Site, Building, or Floor Entrance. Where a system, including a closed-circuit system, permitting voice communication between a visitor and the occupant of the residential dwelling unit is provided, the system shall comply with 708.4. 810 Transportation Facilities 810.1 General. Transportation facilities shall comply with 810. 810.2 Bus Boarding and Alighting Areas. Bus boarding and alighting areas shall comply with 810.2. 810.2.1 Surface. Bus stop boarding and alighting areas shall have a firm, stable surface. 810.2.2 Dimensions. Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches (1525 mm) minimum, measured parallel to the vehicle roadway. 810.2.3 Connection. Bus stop boarding and alighting areas shall be connected to streets, sidewalks, or pedestrian paths by an accessible route complying with 402. 810.2.4 Slope. Parallel to the roadway, the slope of the bus stop boarding and alighting area shall be the same as the roadway, to the maximum extent practicable. Perpendicular to the roadway, the slope of the bus stop boarding and alighting area shall not be steeper than 1:48. 810.3 Bus Shelters. Bus shelters shall provide a minimum clear floor or ground space complying with 305 entirely within the shelter. Bus shelters shall be connected by an accessible route complying with 402 to a boarding and alighting area complying with 810.2. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 810.4 Bus Signs. Bus route identification signs shall comply with 703.5.1 through 703.5.4, and 703.5.7 and 703.5.8. In addition, to the maximum extent practicable, bus route identification signs shall comply with 703.5.5. EXCEPTION: Bus schedules, timetables and maps that are posted at the bus stop or bus bay shall not be required to comply. 810.5 Rail Platforms. Rail platforms shall comply with 810.5. 810.5.1 Slope. Rail platforms shall not exceed a slope of 1:48 in all directions. EXCEPTION: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the slope of the platform parallel to the track shall be permitted to be equal to the slope (grade) of the roadway or existing track. 810.5.2 Detectable Warnings. Platform boarding edges not protected by platform screens or guards shall have detectable warnings complying with 705 along the full length of the public use area of the platform. 810.5.3 Platform and Vehicle Floor Coordination. Station platforms shall be positioned to coordinate with vehicles in accordance with the applicable requirements of 36 CFR Part 1192. Low-level platforms shall be 8 inches (205 mm) minimum above top of rail. EXCEPTION: Where vehicles are boarded from sidewalks or street-level, low-level platforms shall be permitted to be less than 8 inches (205 mm). 810.6 Rail Station Signs. Rail station signs shall comply with 810.6. EXCEPTION. Signs shall not be required to comply with 810.6.1 and 810.6.2 where audible signs are remotely transmitted to hand-held receivers, or are user- or proximity-actuated. 810.6.1 Entrances. Where signs identify a station or its entrance, at least one sign at each entrance shall comply with 703.2 and shall be placed in uniform locations to the maximum extent practicable. Where signs identify a station that has no defined entrance, at least one sign shall comply with 703.2 and shall be placed in a central location. 810.6.2 Routes and Destinations. Lists of stations, routes and destinations served by the station which are located on boarding areas, platforms, or mezzanines shall comply with 703.5. At least one tactile sign identifying the specific station and complying with 703.2 shall be provided on each platform or boarding area. Signs covered by this requirement shall, to the maximum extent practicable, be placed in uniform locations within the system. EXCEPTION: Where sign space is limited, characters shall not be required to exceed 3 inches (75 mm). 810.6.3 Station Names. Stations covered by this section shall have identification signs complying with 703.5. Signs shall be clearly visible and within the sight lines of standing and sitting passengers from within the vehicle on both sides when not obstructed by another vehicle. 810.7 Public Address Systems. Where public address systems convey audible information to the public, the same or equivalent information shall be provided in a visual format. PO 00000 Frm 00069 Fmt 4701 Sfmt 4700 59543 810.8 Clocks. Where clocks are provided for use by the public, the clock face shall be uncluttered so that its elements are clearly visible. Hands, numerals and digits shall contrast with the background either light-ondark or dark-on-light. Where clocks are installed overhead, numerals and digits shall comply with 703.5. 810.9 Escalators. Where provided, escalators shall comply with the sections 6.1.3.5.6 and 6.1.3.6.5 of ASME A17.1 (incorporated by reference, see Referenced Standards’’ in Chapter 1) and shall have a clear width of 32 inches (815 mm) minimum. EXCEPTION: Existing escalators in key stations shall not be required to comply with 810.9. 810.10 Track Crossings. Where a circulation path serving boarding platforms crosses tracks, it shall comply with 402. EXCEPTION: Openings for wheel flanges shall be permitted to be 21⁄2 inches (64 mm) maximum. 811 Storage 811.1 General. Storage shall comply with 811. 811.2 Clear Floor or Ground Space. A clear floor or ground space complying with 305 shall be provided. 811.3 Height. Storage elements shall comply with at least one of the reach ranges specified in 308. 811.4 Operable Parts. Operable parts shall comply with 309. Chapter 9: Built-in Elements 901 General 901.1 Scope. The provisions of Chapter 9 shall apply where required by Chapter 2 or where referenced by a requirement in this document. 902 Dining Surfaces and Work Surfaces 902.1 General. Dining surfaces and work surfaces shall comply with 902.2 and 902.3. EXCEPTION: Dining surfaces and work surfaces for children’s use shall be permitted to comply with 902.4. 902.2 Clear Floor or Ground Space. A clear floor space complying with 305 positioned for a forward approach shall be provided. Knee and toe clearance complying with 306 shall be provided. 902.3 Height. The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground. 902.4 Dining Surfaces and Work Surfaces for Children’s Use. Accessible dining surfaces and work surfaces for children’s use shall comply with 902.4. EXCEPTION: Dining surfaces and work surfaces that are used primarily by children 5 years and younger shall not be required to comply with 902.4 where a clear floor or ground space complying with 305 positioned for a parallel approach is provided. 902.4.1 Clear Floor or Ground Space. A clear floor space complying with 305 positioned for forward approach shall be provided. Knee and toe clearance complying with 306 shall be provided, except that knee clearance 24 inches (610 mm) minimum above the finish floor or ground shall be permitted. E:\FR\FM\26SER2.SGM 26SER2 59544 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 902.4.2 Height. The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish floor or ground. emcdonald on DSK67QTVN1PROD with RULES2 903 Benches 903.1 General. Benches shall comply with 903. 903.2 Clear Floor or Ground Space. Clear floor or ground space complying with 305 shall be provided and shall be positioned at the end of the bench seat and parallel to the short axis of the bench. 903.3 Size. Benches shall have seats that are 42 inches (1065 mm) long minimum and 20 inches (510 mm) deep minimum and 24 inches (610 mm) deep maximum. 903.4 Back Support. The bench shall provide for back support or shall be affixed to a wall. Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat surface. Back support shall be 21⁄2 inches (64 mm) maximum from the rear edge of the seat measured horizontally. 903.5 Height. The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground. 903.6 Structural Strength. Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure. 903.7 Wet Locations. Where installed in wet locations, the surface of the seat shall be slip resistant and shall not accumulate water. 904 Check-Out Aisles and Sales and Service Counters 904.1 General. Check-out aisles and sales and service counters shall comply with the applicable requirements of 904. 904.2 Approach. All portions of counters required to comply with 904 shall be located adjacent to a walking surface complying with 403. 904.3 Check-Out Aisles. Check-out aisles shall comply with 904.3. 904.3.1 Aisle. Aisles shall comply with 403. 904.3.2 Counter. The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground. The top of the counter edge protection shall be 2 inches (51 mm) maximum above the top of the counter surface on the aisle side of the checkout counter. 904.3.3 Check Writing Surfaces. Where provided, check writing surfaces shall comply with 902.3. 904.4 Sales and Service Counters. Sales counters and service counters shall comply with 904.4.1 or 904.4.2. The accessible portion of the counter top shall extend the same depth as the sales or service counter top. EXCEPTION: In alterations, when the provision of a counter complying with 904.4 would result in a reduction of the number of existing counters at work stations or a reduction of the number of existing mail boxes, the counter shall be permitted to have VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 a portion which is 24 inches (610 mm) long minimum complying with 904.4.1 provided that the required clear floor or ground space is centered on the accessible length of the counter. 904.4.1 Parallel Approach. A portion of the counter surface that is 36 inches (915 mm) long minimum and 36 inches (915 mm) high maximum above the finish floor shall be provided. A clear floor or ground space complying with 305 shall be positioned for a parallel approach adjacent to the 36 inch (915 mm) minimum length of counter. EXCEPTION: Where the provided counter surface is less than 36 inches (915 mm) long, the entire counter surface shall be 36 inches (915 mm) high maximum above the finish floor. 904.4.2 Forward Approach. A portion of the counter surface that is 30 inches (760 mm) long minimum and 36 inches (915 mm) high maximum shall be provided. Knee and toe space complying with 306 shall be provided under the counter. A clear floor or ground space complying with 305 shall be positioned for a forward approach to the counter. 904.5 Food Service Lines. Counters in food service lines shall comply with 904.5. 904.5.1 Self-Service Shelves and Dispensing Devices. Self-service shelves and dispensing devices for tableware, dishware, condiments, food and beverages shall comply with 308. 904.5.2 Tray Slides. The tops of tray slides shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground. 904.6 Security Glazing. Where counters or teller windows have security glazing to separate personnel from the public, a method to facilitate voice communication shall be provided. Telephone handset devices, if provided, shall comply with 704.3. Chapter 10: Recreation Facilities 1001 General 1001.1 Scope. The provisions of Chapter 10 shall apply where required by Chapter 2 or where referenced by a requirement in this document. 1002 Amusement Rides 1002.1 General. Amusement rides shall comply with 1002. 1002.2 Accessible Routes. Accessible routes serving amusement rides shall comply with Chapter 4. EXCEPTIONS: 1. In load or unload areas and on amusement rides, where compliance with 405.2 is not structurally or operationally feasible, ramp slope shall be permitted to be 1:8 maximum. 2. In load or unload areas and on amusement rides, handrails provided along walking surfaces complying with 403 and required on ramps complying with 405 shall not be required to comply with 505 where compliance is not structurally or operationally feasible. 1002.3 Load and Unload Areas. A turning space complying with 304.2 and 304.3 shall be provided in load and unload areas. 1002.4 Wheelchair Spaces in Amusement Rides. Wheelchair spaces in amusement rides shall comply with 1002.4. PO 00000 Frm 00070 Fmt 4701 Sfmt 4700 1002.4.1 Floor or Ground Surface. The floor or ground surface of wheelchair spaces shall be stable and firm. 1002.4.2 Slope. The floor or ground surface of wheelchair spaces shall have a slope not steeper than 1:48 when in the load and unload position. 1002.4.3 Gaps. Floors of amusement rides with wheelchair spaces and floors of load and unload areas shall be coordinated so that, when amusement rides are at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5⁄8 inches (16 mm) and the horizontal gap shall be 3 inches (75 mm) maximum under normal passenger load conditions. EXCEPTION: Where compliance is not operationally or structurally feasible, ramps, bridge plates, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall be provided. 1002.4.4 Clearances. Clearances for wheelchair spaces shall comply with 1002.4.4. EXCEPTIONS: 1. Where provided, securement devices shall be permitted to overlap required clearances. 2. Wheelchair spaces shall be permitted to be mechanically or manually repositioned. 3. Wheelchair spaces shall not be required to comply with 307.4. 1002.4.4.1 Width and Length. Wheelchair spaces shall provide a clear width of 30 inches (760 mm) minimum and a clear length of 48 inches (1220 mm) minimum measured to 9 inches (230 mm) minimum above the floor surface. 1002.4.4.2 Side Entry. Where wheelchair spaces are entered only from the side, amusement rides shall be designed to permit sufficient maneuvering clearance for individuals using a wheelchair or mobility aid to enter and exit the ride. 1002.4.4.3 Permitted Protrusions in Wheelchair Spaces. Objects are permitted to protrude a distance of 6 inches (150 mm) maximum along the front of the wheelchair space, where located 9 inches (230 mm) minimum and 27 inches (685 mm) maximum above the floor or ground surface of the wheelchair space. Objects are permitted to protrude a distance of 25 inches (635 mm) maximum along the front of the wheelchair space, where located more than 27 inches (685 mm) above the floor or ground surface of the wheelchair space. 1002.4.5 Ride Entry. Openings providing entry to wheelchair spaces on amusement rides shall be 32 inches (815 mm) minimum clear. 1002.4.6 Approach. One side of the wheelchair space shall adjoin an accessible route when in the load and unload position. 1002.4.7 Companion Seats. Where the interior width of the amusement ride is greater than 53 inches (1345 mm), seating is provided for more than one rider, and the wheelchair is not required to be centered within the amusement ride, a companion seat shall be provided for each wheelchair space. 1002.4.7.1 Shoulder-to-Shoulder Seating. Where an amusement ride provides shoulderto-shoulder seating, companion seats shall be shoulder-to-shoulder with the adjacent wheelchair space. E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 EXCEPTION: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable. 1002.5 Amusement Ride Seats Designed for Transfer. Amusement ride seats designed for transfer shall comply with 1002.5 when positioned for loading and unloading. 1002.5.1 Clear Floor or Ground Space. A clear floor or ground space complying with 305 shall be provided in the load and unload area adjacent to the amusement ride seats designed for transfer. 1002.5.2 Transfer Height. The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area. 1002.5.3 Transfer Entry. Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat. 1002.5.4 Wheelchair Storage Space. Wheelchair storage spaces complying with 305 shall be provided in or adjacent to unload areas for each required amusement ride seat designed for transfer and shall not overlap any required means of egress or accessible route. 1002.6 Transfer Devices for Use with Amusement Rides. Transfer devices for use with amusement rides shall comply with 1002.6 when positioned for loading and unloading. 1002.6.1 Clear Floor or Ground Space. A clear floor or ground space complying with 305 shall be provided in the load and unload area adjacent to the transfer device. 1002.6.2 Transfer Height. The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface. 1002.6.3 Wheelchair Storage Space. Wheelchair storage spaces complying with 305 shall be provided in or adjacent to unload areas for each required transfer device and shall not overlap any required means of egress or accessible route. 1003 Recreational Boating Facilities 1003.1 General. Recreational boating facilities shall comply with 1003. 1003.2 Accessible Routes. Accessible routes serving recreational boating facilities, including gangways and floating piers, shall comply with Chapter 4 except as modified by the exceptions in 1003.2. 1003.2.1 Boat Slips. Accessible routes serving boat slips shall be permitted to use the exceptions in 1003.2.1. EXCEPTIONS: 1. Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4. 2. Gangways shall not be required to comply with the maximum rise specified in 405.6. 3. Where the total length of a gangway or series of gangways serving as part of a required accessible route is 80 feet (24 m) minimum, gangways shall not be required to comply with 405.2. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 4. Where facilities contain fewer than 25 boat slips and the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2. 5. Where gangways connect to transition plates, landings specified by 405.7 shall not be required. 6. Where gangways and transition plates connect and are required to have handrails, handrail extensions shall not be required. Where handrail extensions are provided on gangways or transition plates, the handrail extensions shall not be required to be parallel with the ground or floor surface. 7. The cross slope specified in 403.3 and 405.3 for gangways, transition plates, and floating piers that are part of accessible routes shall be measured in the static position. 8. Changes in level complying with 303.3 and 303.4 shall be permitted on the surfaces of gangways and boat launch ramps. 1003.2.2 Boarding Piers at Boat Launch Ramps. Accessible routes serving boarding piers at boat launch ramps shall be permitted to use the exceptions in 1003.2.2. EXCEPTIONS: 1. Accessible routes serving floating boarding piers shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in 1003.2.1. 2. Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2. 3. Where the accessible route serving a floating boarding pier or skid pier is located within a boat launch ramp, the portion of the accessible route located within the boat launch ramp shall not be required to comply with 405. 1003.3 Clearances. Clearances at boat slips and on boarding piers at boat launch ramps shall comply with 1003.3. 1003.3.1 Boat Slip Clearance. Boat slips shall provide clear pier space 60 inches (1525 mm) wide minimum and at least as long as the boat slips. Each 10 feet (3050 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum. EXCEPTIONS: 1. Clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum, provided that multiple 36 inch (915 mm) wide segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum. 2. Edge protection shall be permitted at the continuous clear openings, provided that it is 4 inches (100 mm) high maximum and 2 inches (51 mm) wide maximum. 3. In existing piers, clear pier space shall be permitted to be located perpendicular to the boat slip and shall extend the width of the boat slip, where the facility has at least one boat slip complying with 1003.3, and further compliance with 1003.3 would result in a reduction in the number of boat slips available or result in a reduction of the widths of existing slips. 1003.3.2 Boarding Pier Clearances. Boarding piers at boat launch ramps shall PO 00000 Frm 00071 Fmt 4701 Sfmt 4700 59545 provide clear pier space 60 inches (1525 mm) wide minimum and shall extend the full length of the boarding pier. Every 10 feet (3050 mm) maximum of linear pier edge shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum. EXCEPTIONS: 1. The clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum provided that multiple 36 inch (915 mm) wide segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum. 2. Edge protection shall be permitted at the continuous clear openings provided that it is 4 inches (100 mm) high maximum and 2 inches (51 mm) wide maximum. 1004 Exercise Machines and Equipment 1004.1 Clear Floor Space. Exercise machines and equipment shall have a clear floor space complying with 305 positioned for transfer or for use by an individual seated in a wheelchair. Clear floor or ground spaces required at exercise machines and equipment shall be permitted to overlap. 1005 Fishing Piers and Platforms 1005.1 Accessible Routes. Accessible routes serving fishing piers and platforms, including gangways and floating piers, shall comply with Chapter 4. EXCEPTIONS: 1. Accessible routes serving floating fishing piers and platforms shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in 1003.2.1. 2. Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2. 1005.2 Railings. Where provided, railings, guards, or handrails shall comply with 1005.2. 1005.2.1 Height. At least 25 percent of the railings, guards, or handrails shall be 34 inches (865 mm) maximum above the ground or deck surface. EXCEPTION: Where a guard complying with sections 1003.2.12.1 and 1003.2.12.2 of the International Building Code (2000 edition) or sections 1012.2 and 1012.3 of the International Building Code (2003 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1) is provided, the guard shall not be required to comply with 1005.2.1. 1005.2.1.1 Dispersion. Railings, guards, or handrails required to comply with 1005.2.1 shall be dispersed throughout the fishing pier or platform. 1005.3 Edge Protection. Where railings, guards, or handrails complying with 1005.2 are provided, edge protection complying with 1005.3.1 or 1005.3.2 shall be provided. 1005.3.1 Curb or Barrier. Curbs or barriers shall extend 2 inches (51 mm) minimum above the surface of the fishing pier or platform. 1005.3.2 Extended Ground or Deck Surface. The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing. Toe clearance shall be provided and shall be 30 inches (760 mm) wide minimum and 9 inches (230 mm) E:\FR\FM\26SER2.SGM 26SER2 59546 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations minimum above the ground or deck surface beyond the railing. 1005.4 Clear Floor or Ground Space. At each location where there are railings, guards, or handrails complying with 1005.2.1, a clear floor or ground space complying with 305 shall be provided. Where there are no railings, guards, or handrails, at least one clear floor or ground space complying with 305 shall be provided on the fishing pier or platform. 1005.5 Turning Space. At least one turning space complying with 304.3 shall be provided on fishing piers and platforms. emcdonald on DSK67QTVN1PROD with RULES2 1006 Golf Facilities 1006.1 General. Golf facilities shall comply with 1006. 1006.2 Accessible Routes. Accessible routes serving teeing grounds, practice teeing grounds, putting greens, practice putting greens, teeing stations at driving ranges, course weather shelters, golf car rental areas, bag drop areas, and course toilet rooms shall comply with Chapter 4 and shall be 48 inches (1220 mm) wide minimum. Where handrails are provided, accessible routes shall be 60 inches (1525 mm) wide minimum. EXCEPTION: Handrails shall not be required on golf courses. Where handrails are provided on golf courses, the handrails shall not be required to comply with 505. 1006.3 Golf Car Passages. Golf car passages shall comply with 1006.3. 1006.3.1 Clear Width. The clear width of golf car passages shall be 48 inches (1220 mm) minimum. 1006.3.2 Barriers. Where curbs or other constructed barriers prevent golf cars from entering a fairway, openings 60 inches (1525 mm) wide minimum shall be provided at intervals not to exceed 75 yards (69 m). 1006.4 Weather Shelters. A clear floor or ground space 60 inches (1525 mm) minimum by 96 inches (2440 mm) minimum shall be provided within weather shelters. 1007 Miniature Golf Facilities 1007.1 General. Miniature golf facilities shall comply with 1007. 1007.2 Accessible Routes. Accessible routes serving holes on miniature golf courses shall comply with Chapter 4. Accessible routes located on playing surfaces of miniature golf holes shall be permitted to use the exceptions in 1007.2. EXCEPTIONS: 1. Playing surfaces shall not be required to comply with 302.2. 2. Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum. 3. A slope not steeper than 1:4 for a 4 inch (100 mm) maximum rise shall be permitted. 4. Ramp landing slopes specified by 405.7.1 shall be permitted to be 1:20 maximum. 5. Ramp landing length specified by 405.7.3 shall be permitted to be 48 inches (1220 mm) long minimum. 6. Ramp landing size specified by 405.7.4 shall be permitted to be 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum. 7. Handrails shall not be required on holes. Where handrails are provided on holes, the VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 handrails shall not be required to comply with 505. 1007.3 Miniature Golf Holes. Miniature golf holes shall comply with 1007.3. 1007.3.1 Start of Play. A clear floor or ground space 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum with slopes not steeper than 1:48 shall be provided at the start of play. 1007.3.2 Golf Club Reach Range Area. All areas within holes where golf balls rest shall be within 36 inches (915 mm) maximum of a clear floor or ground space 36 inches (915 mm) wide minimum and 48 inches (1220 mm) long minimum having a running slope not steeper than 1:20. The clear floor or ground space shall be served by an accessible route. 1008 Play Areas 1008.1 General. Play areas shall comply with 1008. 1008.2 Accessible Routes. Accessible routes serving play areas shall comply with Chapter 4 and 1008.2 and shall be permitted to use the exceptions in 1008.2.1 through 1008.2.3. Where accessible routes serve ground level play components, the vertical clearance shall be 80 inches high (2030 mm) minimum. 1008.2.1 Ground Level and Elevated Play Components. Accessible routes serving ground level play components and elevated play components shall be permitted to use the exceptions in 1008.2.1. EXCEPTIONS: 1. Transfer systems complying with 1008.3 shall be permitted to connect elevated play components except where 20 or more elevated play components are provided no more than 25 percent of the elevated play components shall be permitted to be connected by transfer systems. 2. Where transfer systems are provided, an elevated play component shall be permitted to connect to another elevated play component as part of an accessible route. 1008.2.2 Soft Contained Play Structures. Accessible routes serving soft contained play structures shall be permitted to use the exception in 1008.2.2. EXCEPTION: Transfer systems complying with 1008.3 shall be permitted to be used as part of an accessible route. 1008.2.3 Water Play Components. Accessible routes serving water play components shall be permitted to use the exceptions in 1008.2.3. EXCEPTIONS: 1. Where the surface of the accessible route, clear floor or ground spaces, or turning spaces serving water play components is submerged, compliance with 302, 403.3, 405.2, 405.3, and 1008.2.6 shall not be required. 2. Transfer systems complying with 1008.3 shall be permitted to connect elevated play components in water. 1008.2.4 Clear Width. Accessible routes connecting play components shall provide a clear width complying with 1008.2.4. 1008.2.4.1 Ground Level. At ground level, the clear width of accessible routes shall be 60 inches (1525 mm) minimum. EXCEPTIONS: 1. In play areas less than 1000 square feet (93 m2), the clear width of accessible routes shall be permitted to be 44 inches (1120 mm) minimum, if at least one PO 00000 Frm 00072 Fmt 4701 Sfmt 4700 turning space complying with 304.3 is provided where the restricted accessible route exceeds 30 feet (9145 mm) in length. 2. The clear width of accessible routes shall be permitted to be 36 inches (915 mm) minimum for a distance of 60 inches (1525 mm) maximum provided that multiple reduced width segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum. 1008.2.4.2 Elevated. The clear width of accessible routes connecting elevated play components shall be 36 inches (915 mm) minimum. EXCEPTIONS: 1. The clear width of accessible routes connecting elevated play components shall be permitted to be reduced to 32 inches (815 mm) minimum for a distance of 24 inches (610 mm) maximum provided that reduced width segments are separated by segments that are 48 inches (1220 mm) long minimum and 36 inches (915 mm) wide minimum. 2. The clear width of transfer systems connecting elevated play components shall be permitted to be 24 inches (610 mm) minimum. 1008.2.5 Ramps. Within play areas, ramps connecting ground level play components and ramps connecting elevated play components shall comply with 1008.2.5. 1008.2.5.1 Ground Level. Ramp runs connecting ground level play components shall have a running slope not steeper than 1:16. 1008.2.5.2 Elevated. The rise for any ramp run connecting elevated play components shall be 12 inches (305 mm) maximum. 1008.2.5.3 Handrails. Where required on ramps serving play components, the handrails shall comply with 505 except as modified by 1008.2.5.3. EXCEPTIONS: 1. Handrails shall not be required on ramps located within ground level use zones. 2. Handrail extensions shall not be required. 1008.2.5.3.1 Handrail Gripping Surfaces. Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum. Where the shape of the gripping surface is non-circular, the handrail shall provide an equivalent gripping surface. 1008.2.5.3.2 Handrail Height. The top of handrail gripping surfaces shall be 20 inches (510 mm) minimum and 28 inches (710 mm) maximum above the ramp surface. 1008.2.6 Ground Surfaces. Ground surfaces on accessible routes, clear floor or ground spaces, and turning spaces shall comply with 1008.2.6. 1008.2.6.1 Accessibility. Ground surfaces shall comply with ASTM F1951 (incorporated by reference, see Referenced Standards’’ in Chapter 1). Ground surfaces shall be inspected and maintained regularly and frequently to ensure continued compliance with ASTM F1951. 1008.2.6.2 Use Zones. Ground surfaces located within use zones shall comply with ASTM F1292 (1999 edition or 2004 edition) (incorporated by reference, see ‘‘Referenced Standards’’ in Chapter 1). E:\FR\FM\26SER2.SGM 26SER2 emcdonald on DSK67QTVN1PROD with RULES2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 1008.3 Transfer Systems. Where transfer systems are provided to connect to elevated play components, transfer systems shall comply with 1008.3. 1008.3.1 Transfer Platforms. Transfer platforms shall be provided where transfer is intended from wheelchairs or other mobility aids. Transfer platforms shall comply with 1008.3.1. 1008.3.1.1 Size. Transfer platforms shall have level surfaces 14 inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum. 1008.3.1.2 Height. The height of transfer platforms shall be 11 inches (280 mm) minimum and 18 inches (455 mm) maximum measured to the top of the surface from the ground or floor surface. 1008.3.1.3 Transfer Space. A transfer space complying with 305.2 and 305.3 shall be provided adjacent to the transfer platform. The 48 inch (1220 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform. The side of the transfer platform serving the transfer space shall be unobstructed. 1008.3.1.4 Transfer Supports. At least one means of support for transferring shall be provided. 1008.3.2 Transfer Steps. Transfer steps shall be provided where movement is intended from transfer platforms to levels with elevated play components required to be on accessible routes. Transfer steps shall comply with 1008.3.2. 1008.3.2.1 Size. Transfer steps shall have level surfaces 14 inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum. 1008.3.2.2 Height. Each transfer step shall be 8 inches (205 mm) high maximum. 1008.3.2.3 Transfer Supports. At least one means of support for transferring shall be provided. 1008.4 Play Components. Ground level play components on accessible routes and elevated play components connected by ramps shall comply with 1008.4. 1008.4.1 Turning Space. At least one turning space complying with 304 shall be provided on the same level as play components. Where swings are provided, the turning space shall be located immediately adjacent to the swing. 1008.4.2 Clear Floor or Ground Space. Clear floor or ground space complying with 305.2 and 305.3 shall be provided at play components. 1008.4.3 Play Tables. Where play tables are provided, knee clearance 24 inches (610 mm) high minimum, 17 inches deep (430 mm) minimum, and 30 inches (760 mm) wide minimum shall be provided. The tops of rims, curbs, or other obstructions shall be 31 inches (785 mm) high maximum. EXCEPTION: Play tables designed and constructed primarily for children 5 years and younger shall not be required to provide knee clearance where the clear floor or ground space required by 1008.4.2 is arranged for a parallel approach. 1008.4.4 Entry Points and Seats. Where play components require transfer to entry points or seats, the entry points or seats shall VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground space. EXCEPTION: Entry points of slides shall not be required to comply with 1008.4.4. 1008.4.5 Transfer Supports. Where play components require transfer to entry points or seats, at least one means of support for transferring shall be provided. 1009 Swimming Pools, Wading Pools, and Spas 1009.1 General. Where provided, pool lifts, sloped entries, transfer walls, transfer systems, and pool stairs shall comply with 1009. 1009.2 Pool Lifts. Pool lifts shall comply with 1009.2. 1009.2.1 Pool Lift Location. Pool lifts shall be located where the water level does not exceed 48 inches (1220 mm). EXCEPTIONS: 1. Where the entire pool depth is greater than 48 inches (1220 mm), compliance with 1009.2.1 shall not be required. 2. Where multiple pool lift locations are provided, no more than one pool lift shall be required to be located in an area where the water level is 48 inches (1220 mm) maximum. 1009.2.2 Seat Location. In the raised position, the centerline of the seat shall be located over the deck and 16 inches (405 mm) minimum from the edge of the pool. The deck surface between the centerline of the seat and the pool edge shall have a slope not steeper than 1:48. 1009.2.3 Clear Deck Space. On the side of the seat opposite the water, a clear deck space shall be provided parallel with the seat. The space shall be 36 inches (915 mm) wide minimum and shall extend forward 48 inches (1220 mm) minimum from a line located 12 inches (305 mm) behind the rear edge of the seat. The clear deck space shall have a slope not steeper than 1:48. 1009.2.4 Seat Height. The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the raised (load) position. 1009.2.5 Seat Width. The seat shall be 16 inches (405 mm) wide minimum. 1009.2.6 Footrests and Armrests. Footrests shall be provided and shall move with the seat. If provided, the armrest positioned opposite the water shall be removable or shall fold clear of the seat when the seat is in the raised (load) position. EXCEPTION: Footrests shall not be required on pool lifts provided in spas. 1009.2.7 Operation. The lift shall be capable of unassisted operation from both the deck and water levels. Controls and operating mechanisms shall be unobstructed when the lift is in use and shall comply with 309.4. 1009.2.8 Submerged Depth. The lift shall be designed so that the seat will submerge to a water depth of 18 inches (455 mm) minimum below the stationary water level. 1009.2.9 Lifting Capacity. Single person pool lifts shall have a weight capacity of 300 pounds. (136 kg) minimum and be capable of sustaining a static load of at least one and a half times the rated load. PO 00000 Frm 00073 Fmt 4701 Sfmt 4700 59547 1009.3 Sloped Entries. Sloped entries shall comply with 1009.3. 1009.3.1 Sloped Entries. Sloped entries shall comply with Chapter 4 except as modified in 1109.3.1 through 1109.3.3. EXCEPTION: Where sloped entries are provided, the surfaces shall not be required to be slip resistant. 1009.3.2 Submerged Depth. Sloped entries shall extend to a depth of 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level. Where landings are required by 405.7, at least one landing shall be located 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level. EXCEPTION: In wading pools, the sloped entry and landings, if provided, shall extend to the deepest part of the wading pool. 1009.3.3 Handrails. At least two handrails complying with 505 shall be provided on the sloped entry. The clear width between required handrails shall be 33 inches (840 mm) minimum and 38 inches (965 mm) maximum. EXCEPTIONS: 1. Handrail extensions specified by 505.10.1 shall not be required at the bottom landing serving a sloped entry. 2. Where a sloped entry is provided for wave action pools, leisure rivers, sand bottom pools, and other pools where user access is limited to one area, the handrails shall not be required to comply with the clear width requirements of 1009.3.3. 3. Sloped entries in wading pools shall not be required to provide handrails complying with 1009.3.3. If provided, handrails on sloped entries in wading pools shall not be required to comply with 505. 1009.4 Transfer Walls. Transfer walls shall comply with 1009.4. 1009.4.1 Clear Deck Space. A clear deck space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall. Where one grab bar is provided, the clear deck space shall be centered on the grab bar. Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars. 1009.4.2 Height. The height of the transfer wall shall be 16 inches (405 mm) minimum and 19 inches (485 mm) maximum measured from the deck. 1009.4.3 Wall Depth and Length. The depth of the transfer wall shall be 12 inches (305 mm) minimum and 16 inches (405 mm) maximum. The length of the transfer wall shall be 60 inches (1525 mm) minimum and shall be centered on the clear deck space. 1009.4.4 Surface. Surfaces of transfer walls shall not be sharp and shall have rounded edges. 1009.4.5 Grab Bars. At least one grab bar complying with 609 shall be provided on the transfer wall. Grab bars shall be perpendicular to the pool wall and shall extend the full depth of the transfer wall. The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls. Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar. Where two grab bars are provided, clearance between grab bars shall be 24 inches (610 mm) minimum. E:\FR\FM\26SER2.SGM 26SER2 59548 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations EXCEPTION: Grab bars on transfer walls shall not be required to comply with 609.4. 1009.5 Transfer Systems. Transfer systems shall comply with 1009.5. 1009.5.1 Transfer Platform. A transfer platform shall be provided at the head of each transfer system. Transfer platforms shall provide 19 inches (485 mm) minimum clear depth and 24 inches (610 mm) minimum clear width. 1009.5.2 Transfer Space. A transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall be centered along a 24 inch (610 mm) minimum side of the transfer platform. The side of the transfer platform serving the transfer space shall be unobstructed. 1009.5.3 Height. The height of the transfer platform shall comply with 1009.4.2. 1009.5.4 Transfer Steps. Transfer step height shall be 8 inches (205 mm) maximum. The surface of the bottom tread shall extend to a water depth of 18 inches (455 mm) minimum below the stationary water level. 1009.5.5 Surface. The surface of the transfer system shall not be sharp and shall have rounded edges. 1009.5.6 Size. Each transfer step shall have a tread clear depth of 14 inches (355 mm) minimum and 17 inches (430 mm) maximum and shall have a tread clear width of 24 inches (610 mm) minimum. 1009.5.7 Grab Bars. At least one grab bar on each transfer step and the transfer platform or a continuous grab bar serving each transfer step and the transfer platform shall be provided. Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above each step and transfer platform. Where a continuous grab bar is provided, the top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above the step nosing and transfer platform. Grab bars shall comply with 609 and be located on at least one side of the transfer system. The grab bar located at the transfer platform shall not obstruct transfer. EXCEPTION: Grab bars on transfer systems shall not be required to comply with 609.4. 1009.6 Pool Stairs. Pool stairs shall comply with 1009.6. 1009.6.1 Pool Stairs. Pool stairs shall comply with 504. EXCEPTION: Pool step riser heights shall not be required to be 4 inches (100 mm) high minimum and 7 inches (180 mm) high maximum provided that riser heights are uniform. 1009.6.2 Handrails. The width between handrails shall be 20 inches (510 mm) minimum and 24 inches (610 mm) maximum. Handrail extensions required by 505.10.3 shall not be required on pool stairs. 1010 Shooting Facilities With Firing Positions 1010.1 Turning Space. A circular turning space 60 inches (1525 mm) diameter minimum with slopes not steeper than 1:48 shall be provided at shooting facilities with firing positions. 1011 Outdoor Constructed Features 1011.1 General. All outdoor constructed features shall comply with 1011.2 and 1011.3. Outdoor constructed features specified in 1011.4 through 1011.8 shall comply with those provisions, as applicable. 1011.2 Clear Ground Space. A clear ground space complying with 1011.2 shall be provided at outdoor constructed features. EXCEPTIONS: 1. Where individual outdoor constructed features are altered and the ground surface is not altered, the clear ground space shall not be required to comply with 1011.2.2 and 1011.2.3. 2. In alterations, when an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1011.2, the clear ground space shall comply with the provision to the extent practicable. 1011.2.1 Size and Location. The size and location of the clear ground space shall be in accordance with Table 1011.2.1. Unless otherwise specified in Table 1011.2.1, one full unobstructed side of the clear ground space shall adjoin or overlap an outdoor recreation access route or a trail, as applicable, or another clear ground space. TABLE 1011.2.1—CLEAR GROUND SPACE Outdoor constructed feature Minimum size and location Picnic tables ......................... Fire rings, grills, fireplaces, and woodstoves. Trash and recycling receptacles. Water hydrants ..................... 36 inches (915 mm) on all usable sides of the table measured from the back edge of the benches. 48 inches (1220 mm) by 48 inches (1220 mm) on all usable sides of the fire ring, grill, fireplace, and woodstove Center the space on each usable side of the grill, fireplace, and woodstove. 36 inches (915 mm) by 48 inches (1220 mm) positioned for forward approach to the receptacle opening; or 30 inches (760 mm) by 60 inches (1525 mm) positioned for a parallel approach to the receptacle opening. 72 inches (1830 mm) by 48 inches (1220 mm) with the long side of the space adjoining or overlapping an outdoor recreation access route or trail, as applicable, or another clear ground space. Locate the space so that the water spout is 11 inches (280 mm) minimum and 12 inches (305 mm) maximum from the rear center of the long side of the space. 30 inches (760 mm) by 60 inches (1525 mm) with the long side of the space adjoining or overlapping an accessible parking space or pull-up space for recreational vehicles. Locate the space so that the hook-ups are at the rear center of the space. Bollards or other barriers shall not obstruct the clear ground space in front of the hook-ups. 60 inches (1525 mm) by 60 inches (1525 mm) centered on the shower heads. Locate the space so that the shower pedestal or wall with the shower head are at the rear end of the space. 36 inches (915 mm) by 48 inches (1220 mm) positioned near the bench with one side of the space adjoining an outdoor recreation access route or trail, as applicable. The clear ground space shall not overlap the outdoor recreation access route or trail, or another clear ground space. 36 inches (915 mm) by 48 inches (1220 mm) positioned for forward approach to the viewing scope. Provide knee and toe clearance complying with 306 under the viewing scope. Locate the space so that the eyepiece is centered on the space. Utility and sewage hookups Outdoor rinsing showers ...... Benches ............................... emcdonald on DSK67QTVN1PROD with RULES2 Viewing Scopes .................... 1011.2.2 Surface. The surface of the clear ground space shall be firm and stable. 1011.2.3 Slope. The slope of the clear ground space surface shall not be steeper than 1:48 in any direction. EXCEPTION: Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 shall be permitted when necessary for drainage. 1011.2.4 Openings. Openings in the clear ground space surface shall not allow the VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 passage of a sphere more than 1⁄2 inch (13 mm) in diameter. 1011.3 Operable Parts. Operable parts shall comply with 309.3 and 309.4. EXCEPTIONS: 1. Fire rings, grills, fireplaces, wood stoves, water hydrants, and water utility hookups shall comply with 309.4 to the extent practicable. 2. Trash and recycling receptacles with hinged lids and controls to keep out large PO 00000 Frm 00074 Fmt 4701 Sfmt 4700 animals shall comply with 309.4 to the extent practicable. 3. Dumpster type trash and recycling receptacles shall not be required to comply with 309.3 and 309.4. 4. Sewage hatches shall not be required to comply with 309.3 and 309.4. 1011.4 Picnic Tables. Picnic tables shall comply with 1011.4. 1011.4.1 Height. The tops of picnic tables shall comply with 902.3. E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 1011.4.2 Wheelchair Space. Picnic tables shall provide at least one wheelchair space for each 24 linear feet (7320 mm) of usable table surface perimeter. Wheelchair spaces shall be 30 inches (760 mm) minimum by 48 inches (1220 mm) minimum. Wheelchair spaces shall be positioned for a forward approach to the table and provide knee and toe clearance complying with 306 under the table. 1011.5 Fire Rings, Grills, Fireplaces, and Wood Stoves. Fire rings, grills, fireplaces, and wood stoves shall comply with 1011.5. 1011.5.1 Fire Building Surfaces. Fire building surfaces shall be 9 inches (230 mm) minimum above the ground. 1011.5.2 Cooking Surfaces. Where provided, cooking surfaces shall be 15 inches (380 mm) minimum and 34 inches (865 mm) maximum above the ground. 1011.5.3 Raised Edges or Walls. Where fire rings, grills, or fireplaces are constructed with raised edges or walls, the depth of the raised edge or wall shall be 10 inches (255 mm) maximum. 1011.6 Water Spouts. Water spouts at water hydrants and water utility hook-ups shall be 28 inches (710 mm) minimum and 36 inches (915 mm) maximum above the ground. 1011.7 Outdoor Rinsing Showers. Outdoor rinsing showers shall provide at least one hand-held shower spray unit with a hose 59 inches (1500 mm) long minimum. The hand-held shower spray unit shall have at least one fixed position located 15 inches minimum (380 mm) and 48 inches (1220 mm) maximum above the ground. EXCEPTION: Where vandalism is a consideration, a fixed shower head located at 48 in (1220 mm) above the ground shall be permitted in place of a hand-held shower spray unit. 1011.8 Viewing Scopes. Eyepieces on viewing scopes shall be 43 inches (1090 mm) minimum and 51 inches (1295 mm) maximum above the ground. emcdonald on DSK67QTVN1PROD with RULES2 1012 Parking Spaces Within Camping Units and Picnic Units and Pull-up Spaces at Dump Stations 1012.1 General. Parking spaces within camping units and picnic units with mobility features and pull-up spaces for recreational vehicles at dump stations shall comply with 1012. 1012.2 Recreational Vehicles. Parking spaces and pull-up spaces for recreational vehicles shall be 20 feet (6100 mm) wide minimum. EXCEPTION: Where two adjacent parking spaces are provided for recreational vehicles, one parking space shall be permitted to be 16 feet (4880 mm) wide minimum. 1012.3 Other Vehicles. Parking spaces for vehicles, other than recreational vehicles, shall be 16 feet (4880 mm) wide minimum. EXCEPTION: Where two adjacent parking spaces are provided for vehicles, other than recreational vehicles, one parking space shall be permitted to be 8 feet (2440 mm) wide minimum. 1012.4 Surface. The surface of parking spaces and pull-up spaces shall be firm and stable. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 1012.5 Slope. The slope of the surface of parking spaces and pull-up spaces shall not be steeper than 1:48 in any direction. EXCEPTION: Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 shall be permitted when necessary for drainage. 1013 Tent Pads and Tent Platforms 1013.1 General. Tent pads and tent platforms shall comply with 1013. EXCEPTION: When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1013, the tent pad and tent platform shall comply with the provision to the extent practicable. 1013.2 Clear Ground Space. Clear ground space complying with 1013.2 shall be provided on all usable sides of tent pads and tent platforms. 1013.2.1 Size. The clear ground space shall be 48 inches (1220 mm) wide minimum. 1013.2.2 Surface. The surface of the clear ground space shall be firm and stable. The surface shall allow use of tent stakes and other tent securement devices. 1013.3 Slope. The slope of the surface of tent pads, tent platforms, and clear ground spaces shall not be steeper than 1:48 in any direction. EXCEPTION: Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 shall be permitted where necessary for drainage. 1013.4 Height. Tent platforms shall be 19 inches (485 mm) high maximum measured from the clear ground space to the tent platform surface. 1014 Camp Shelters 1014.1 General. Camp shelters shall comply with 1014. EXCEPTIONS: 1. When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1014, the camp shelter shall comply with the provision to the extent practicable. 2. Camp shelters shall not be required to comply with 307. 1014.2 Entrance. Camp shelters shall provide an entrance complying with 1014.2.1 or 1014.2.2. 1014.2.1 Transfer Access. Where transfer access is provided at the entrance to a camp shelter, the entrance shall comply with 1014.2.1. 1014.2.1.1 Clear Ground Space. A clear ground space shall be provided at the entrance to the camp shelter. The clear ground space shall be 36 inches (915 mm) minimum by 48 inches (1220 mm) minimum and shall be positioned for a parallel approach to the camp shelter. One full unobstructed side of the clear ground space shall adjoin or overlap an outdoor recreation access route or trail, as applicable, or another clear ground space. 1014.2.1.1.1 Surface. The surface of the clear ground space shall be firm and stable. 1014.2.1.1.2 Slope. The slope of the surface of the clear ground space shall not be steeper than 1:48 in any direction. EXCEPTION: Where the surface is other than asphalt, concrete, or boards, slopes not PO 00000 Frm 00075 Fmt 4701 Sfmt 4700 59549 steeper than 1:20 shall be permitted where necessary for drainage. 1014.2.1.2 Floor Height. The camp shelter floor at the entrance shall be 19 inches (485 mm) high maximum measured from the clear ground space. 1014.2.2 Roll-in Access. Where roll-in access is provided at the entrance to a camp shelter, the entrance shall comply with 1014.2.2. 1014.2.2.1 Level or Sloped Entry Route. Camp shelters providing roll-in access shall have a level or sloped entry route complying 1016 or 1017, as applicable. 1014.2.2.2 Turning Space. A turning space complying with 304.3 shall be provided within the camp shelter. 1014.3 Floor. The floor within camp shelters shall comply with 1014.3. 1014.3.1 Surface. The floor surface shall be firm and stable. 1014.3.2 Slope. The slope of the floor surface shall not be steeper than 1:48 in any direction. EXCEPTION: Where the floor surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 shall be permitted when necessary for drainage. 1015 Viewing Areas 1015.1 General. Viewing areas shall comply with 1015. EXCEPTION: In alterations, when an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1015, the viewing area shall comply with the provision to the extent practicable. 1015.2 Clear Ground Space. A clear ground space shall be provided at each distinct viewing location. The clear ground space shall be 36 inches (915 mm) minimum by 48 inches (1220 mm) minimum and shall be positioned for either a forward or parallel approach to the viewing location. One full unobstructed side of the clear ground space shall adjoin or overlap an outdoor recreation access route or trail, as applicable, or another clear ground space. 1015.3 Viewing Space. Each distinct viewing location shall provide a viewing space adjacent to the clear ground space required by 1015.2 through which the point of interest is viewable. The viewing space shall be 32 inches (815 mm) maximum and 51 inches (1295 mm) minimum high above the ground and shall extend the full width of the clear ground space. EXCEPTION: Guards or similar safety barriers shall be permitted to obstruct the viewing space to the extent the obstruction is necessary for the guard or safety barrier to serve its intended purpose. 1015.4 Turning Space. A turning space complying with 304.3 shall be provided within viewing areas. 1015.5 Surface. The surface of clear ground spaces and turning spaces shall be firm and stable. 1015.6 Slope. The slope of the surface of clear ground spaces and turning spaces shall not be steeper than 1:48 in any direction. EXCEPTION: Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 shall be permitted when necessary for drainage. E:\FR\FM\26SER2.SGM 26SER2 59550 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 1016 Outdoor Recreation Access Routes 1016.1 General. Outdoor recreation access routes shall comply with 1016. EXCEPTIONS: 1. In alterations to existing camping facilities, picnic facilities, and trailheads, when an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1016 on a portion of an outdoor recreation access route, the portion of the outdoor recreation access route shall comply with the provision to the extent practicable. 2. At viewing areas, when an entity determines that a condition in 1019 does not permit full compliance on a portion of an outdoor recreation access route with a specific provision in 1016, the portion of the outdoor recreation access route shall comply with the provision to the extent practicable. 3. Where outdoor recreation access routes are provided within vehicular ways, outdoor recreation access routes shall not be required to comply with 1016.4, 1016.7, and 1016.8. 1016.2 Surface. The surface of outdoor recreation access routes, passing spaces, and resting intervals shall be firm and stable. 1016.3 Clear Width. The clear width of outdoor recreation access routes shall be 36 inches (915 mm) minimum. 1016.4 Passing Spaces. Outdoor recreation access routes with a clear width less than 60 inches (1525 mm) shall provide passing spaces complying with 1016.4 at intervals of 200 feet (61 m) maximum. Passing spaces and resting intervals shall be permitted to overlap. 1016.4.1 Size. The passing space shall be either: 1. A space 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum; or 2. The intersection of two outdoor recreation access routes providing a T-shaped space complying with 304.3.2 where the base and the arms of the T-shaped space extend 48 inches (1220 mm) minimum beyond the intersection. Vertical alignment at the intersection of the outdoor recreation access routes that form the T-shaped space shall be nominally planar. 1016.5 Obstacles. Obstacles on outdoor recreation access routes, passing spaces, and resting intervals shall not exceed 1⁄2 inch (13 mm) in height measured vertically to the highest point. EXCEPTION: Where the surface is other than asphalt, concrete, or boards, obstacles shall be permitted to not exceed 1 inch (25 mm) in height measured vertically to the highest point. 1016.6 Openings. Openings in the surface of outdoor recreation access routes shall not allow the passage of a sphere more than 1⁄2 inch (13 mm) in diameter. 1016.7 Slopes. The slopes of outdoor recreation access routes shall comply with 1016.7. 1016.7.1 Maximum Running Slope and Segment Length. The running slope of any segment of an outdoor recreation access route shall not be steeper than 1:10 (10%). Where the running slope of a segment of an outdoor recreation access route is steeper than 1:20 (5%), the maximum length of the segment shall be in accordance with Table 1016.7.1, and a resting interval complying with 1016.8 shall be provided at the top and bottom of each segment. TABLE 1016.7.1—MAXIMUM RUNNING SLOPE AND SEGMENT LENGTH Running slope of outdoor recreation access route segment Maximum length of segment But not steeper than 1:20 (5%) ........................................................... 1:12 (8.33%) ...................................................... emcdonald on DSK67QTVN1PROD with RULES2 Steeper than 1:12 (8.33%) ..................................................... 1:10 (10%) ........................................................ 50 feet (15 m). 30 feet (9 m). 1016.7.2 Cross Slope. The cross slope shall not be steeper than 1:48. EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage. 1016.8 Resting Intervals. Resting intervals shall comply with 1016.8. 1016.8.1 Length. The resting interval length shall be 60 inches (1525 mm) long minimum. 1016.8.2 Width. Where resting intervals are provided within an outdoor recreation access route, resting intervals shall be at least as wide as the widest segment of the outdoor recreation access route leading to the resting interval. Where resting intervals are provided adjacent to an outdoor recreation access route, the resting interval shall be 36 inches (915 mm) wide minimum. 1016.8.3 Slope. Resting intervals shall have slopes not steeper than 1:48 in any direction. EXCEPTION: Where the surface is other than concrete, asphalt, or boards, slopes not steeper than 1:20 shall be permitted when necessary for drainage. 1016.8.4 Turning Space. Where resting intervals are provided adjacent to an outdoor recreation access route, a turning space complying with 304.3.2 shall be provided. Vertical alignment between the outdoor recreation access route, turning space, and resting interval shall be nominally planar. 1016.9 Protruding Objects. Constructed elements on outdoor recreation access routes, passing spaces, and resting intervals shall comply with 307. 2. The intersection of two trails providing a T-shaped space complying with 304.3.2 where the base and the arms of the T-shaped space extend 48 inches (1220 mm) minimum beyond the intersection. Vertical alignment at the intersection of the trails that form the Tshaped space shall be nominally planar. 1017.5 Tread Obstacles. Tread obstacles on trails, passing spaces, and resting intervals shall not exceed 1⁄2 inch (13 mm) in height measured vertically to the highest point. EXCEPTION: Where the surface is other than asphalt, concrete, or boards, tread obstacles shall be permitted to not exceed 2 inches (50 mm) in height measured vertically to the highest point. 1017.6 Openings. Openings in the surface of trails, passing spaces, and resting intervals shall not allow the passage of a sphere more than 1⁄2 inch (13 mm) in diameter. 1017.7 Slopes. The slopes of trails shall comply with 1017.7. 1017.7.1 Maximum Running Slope and Segment Length. Not more than 30 percent of the total length of a trail shall have a running slope steeper than 1:12 (8.33%). The running slope of any segment of a trail shall not be steeper than 1:8 (12%). Where the running slope of a segment of a trail is steeper than 1:20 (5%), the maximum length of the segment shall be in accordance with Table 1017.7.1, and a resting interval complying with 1017.8 shall be provided at the top and bottom of each segment. VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 1017 Trails 1017.1 General. Trails shall comply with 1017. EXCEPTIONS: 1. When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1017 on a portion of a trail, the portion of the trail shall comply with the provision to the extent practicable. 2. After applying Exception 1, when an entity determines that it is impracticable for the entire trail to comply with 1017, the trail shall not be required to comply with 1017. 1017.2 Surface. The surface of trails, passing spaces, and resting intervals shall be firm and stable. 1017.3 Clear Tread Width. The clear tread width of trails shall be 36 inches (915 mm) minimum. 1017.4 Passing Spaces. Trails with a clear tread width less than 60 inches (1525 mm) shall provide passing spaces complying with 1017.4 at intervals of 1000 feet (300 m) maximum. Where the full length of a trail does not fully comply with 1017, a passing space shall be located at the end of the trail segment that fully complies with 1017. Passing spaces and resting intervals shall be permitted to overlap. 1017.4.1 Size. The passing space shall be either: 1. A space 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum; or PO 00000 Frm 00076 Fmt 4701 Sfmt 4700 E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 59551 TABLE 1017.7.1—MAXIMUM RUNNING SLOPE AND SEGMENT LENGTH Running slope of trail segment Maximum length of segment Steeper than But not steeper than 1:20 (5%) ........................................................... 1:12 (8.33%) ...................................................... 1:10 (10%) ......................................................... 1:12 (8.33%) ..................................................... 1:10 (10%) ........................................................ 1:8 (12%) .......................................................... 200 feet (61 m). 30 feet (9 m). 10 feet (3050 mm). 1017.7.2 Cross Slope. The cross slope shall be not be steeper than 1:48. EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage. 1017.8 Resting Intervals. Resting intervals shall comply with 1017.8. 1017.8.1 Length. The resting interval length shall be 60 inches (1525 mm) long minimum. 1017.8.2 Width. Where resting intervals are provided within the trail tread, resting intervals shall be at least as wide as the widest segment of the trail tread leading to the resting interval. Where resting intervals are provided adjacent to the trail tread, the resting interval clear width shall be 36 inches (915 mm) minimum. 1017.8.3 Slope. Resting intervals shall have slopes not steeper than 1:48 in any direction. EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage. 1017.8.4 Turning Space. Where resting intervals are provided adjacent to the trail tread, a turning space complying with 304.3.2 shall be provided. Vertical alignment between the trail tread, turning space, and resting interval shall be nominally planar. 1017.9 Protruding Objects. Constructed elements on trails, passing spaces, and resting intervals shall comply with 307. 1017.10 Trailhead Signs. Trail information signs at trailheads shall include the following: 1. Length of the trail or trail segment; 2. Surface type; 3. Typical and minimum tread width; 4. Typical and maximum running slope; and 5. Typical and maximum cross slope. 1018.3 Surface. The surface of beach access routes and resting intervals shall be firm and stable. 1018.4 Clear Width. The clear width of beach access routes shall be 60 inches (1525 mm) minimum. EXCEPTION: At dune crossings, the clear width of beach access routes that are not removable shall be permitted to be reduced to 48 inches (1220 mm) minimum. 1018.5 Obstacles. Obstacles on beach access routes and resting intervals shall not exceed 1⁄2 inch (13 mm) in height measured vertically to the highest point. EXCEPTION: Where the surface is other than asphalt, concrete, or boards, obstacles shall be permitted to not exceed 1 inch (25 mm) in height measured vertically to the highest point. 1018.6 Openings. Openings in the surface of beach access routes and resting intervals shall not allow the passage of a sphere more than 1⁄2 inch (13 mm) in diameter. 1018.7 Slopes. The slopes of beach access routes shall comply with 1018.7. 1018.7.1 Maximum Running Slope and Segment Length. The running slope of any segment of a beach access route shall not be steeper than 1:10 (10%). Where the running slope of a segment of a beach access route is steeper than 1:20 (5%), the maximum length of the segment shall be in accordance with Table 1018.7.1, and a resting interval complying with 1018.8 shall be provided at the top and bottom of each segment. 1018 Beach Access Routes 1018.1 General. Beach access routes shall comply with 1018. EXCEPTIONS: 1. When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1018 on a portion of a beach access route, the portion of the beach access route shall comply with the provision to the extent practicable. 2. After applying Exception 1, when an entity determines that it is impracticable to provide a beach access route complying with 1018, a beach access route shall not be required. 3. Removable beach access routes shall not be required to comply with 1018.7, 1018.8, and 1018.10. 1018.2 Connections. Beach access routes shall connect an entry point to the beach to the: 1. High tide level at tidal beaches; 2. Mean high water level at river beaches; or 3. Normal recreation water level at lake, pond, and reservoir beaches. TABLE 1018.7.1—MAXIMUM RUNNING SLOPE AND SEGMENT LENGTH Running slope of beach access route segment Maximum length of segment But not steeper than 1:20 (5%) ........................................................... 1:12 (8.33%) ...................................................... emcdonald on DSK67QTVN1PROD with RULES2 Steeper than 1:12 (8.33%) ..................................................... 1:10 (10%) ........................................................ 50 feet (15 m). 30 feet (9 m). 1018.7.2 Cross Slope. The cross slope shall not be steeper than 1:48. EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage. 1018.8 Resting Intervals. Resting intervals shall comply with 1018.8. 1018.8.1 Size. Resting intervals shall be 60 inches minimum (1525 mm) by 60 inches (1525 mm) minimum. 1018.8.2 Slope. Resting intervals shall have a slope not steeper than 1:48 in any direction. EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage. 1018.9 Protruding Objects. Constructed elements on beach access routes and resting intervals shall comply with 307. 1018.10 Dune Crossings. Where the slope of a beach access route at a dune crossing is steeper than 1:20 (5%), handrails complying with 505 and curbs or barriers shall be provided. The curbs or barriers shall prevent the passage of a 2 inch (50 mm) diameter sphere, where any portion of the sphere is within 2 inches (50 mm) of the crossing surface. 1019 VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 PO 00000 Frm 00077 Fmt 4701 Sfmt 4700 Conditions for Exceptions 1019.1 General. Exceptions to specific provisions in 1011, 1013, 1014, 1015, 1016, 1017, and 1018 shall be permitted when an entity determines that any of the following conditions does not permit full compliance with the provision: 1. Compliance is not practicable due to terrain. 2. Compliance cannot be accomplished with the prevailing construction practices. 3. Compliance would fundamentally alter the function or purpose of the facility or the setting. 4. Compliance is limited or precluded by any of the following laws, or by decisions or E:\FR\FM\26SER2.SGM 26SER2 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations emcdonald on DSK67QTVN1PROD with RULES2 opinions issued or agreements executed pursuant to any of the following laws: • Endangered Species Act (16 U.S.C. 1531 et seq.); • National Environmental Policy Act (42 U.S.C. 4321 et seq.); VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 • National Historic Preservation Act (16 U.S.C. 470 et seq.); • Wilderness Act (16 U.S.C. 1131 et seq.); or • Other federal, state, or local law the purpose of which is to preserve threatened or PO 00000 Frm 00078 Fmt 4701 Sfmt 4725 endangered species; the environment; or archaeological, cultural, historical, or other significant natural features. BILLING CODE 8150–01–P E:\FR\FM\26SER2.SGM 26SER2 ER26SE13.007</GPH> 59552 Federal Register / Vol. 78, No. 187 / Thursday, September 26, 2013 / Rules and Regulations 59553 APPENDIX E TO PART 1191 [Removed and Reserved] 8. Remove and reserve Appendix E to this part. ■ [FR Doc. 2013–22876 Filed 9–25–13; 8:45 am] VerDate Mar<15>2010 18:25 Sep 25, 2013 Jkt 229001 PO 00000 Frm 00079 Fmt 4701 Sfmt 9990 E:\FR\FM\26SER2.SGM 26SER2 ER26SE13.008</GPH> emcdonald on DSK67QTVN1PROD with RULES2 BILLING CODE 8150–01–C

Agencies

Architectural and Transportation Barriers Compliance Board

[Federal Register Volume 78, Number 187 (Thursday, September 26, 2013)]
[Rules and Regulations]
[Pages 59475-59553]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2013-22876]

[[Page 59475]]

Vol. 78

Thursday,

No. 187

September 26, 2013

Part III

Architectural and Transportation Barriers Compliance Board

-----------------------------------------------------------------------

36 CFR Part 1191

Architectural Barriers Act Accessibility Guidelines; Outdoor Developed
Areas; Final Rule

Federal Register / Vol. 78 , No. 187 / Thursday, September 26, 2013 /
Rules and Regulations

[[Page 59476]]

-----------------------------------------------------------------------

ARCHITECTURAL AND TRANSPORTATION BARRIERS COMPLIANCE BOARD

36 CFR Part 1191

RIN 3014-AA22

Architectural Barriers Act Accessibility Guidelines; Outdoor
Developed Areas

AGENCY: Architectural and Transportation Barriers Compliance Board.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We, the Architectural and Transportation Barriers Compliance
Board (Access Board), are issuing a final rule that amends the
Architectural Barriers Act Accessibility Guidelines by adding scoping
and technical requirements for camping facilities, picnic facilities,
viewing areas, trails, and beach access routes constructed or altered
by or on behalf of federal agencies. The final rule ensures that these
facilities are readily accessible to and usable by individuals with
disabilities. The final rule applies to the following federal agencies
and their components that administer outdoor areas developed for
recreational purposes: Department of Agriculture (Forest Service);
Department of Defense (Army Corps of Engineers); and Department of the
Interior (Bureau of Land Management, Bureau of Reclamation, Fish and
Wildlife Service, National Park Service). The final rule also applies
to non-federal entities that construct or alter recreation facilities
on federal land on behalf of the federal agencies pursuant to a
concession contract, partnership agreement, or similar arrangement.

DATES: The final rule is effective November 25, 2013. The incorporation
of certain publications listed in the guidelines is approved by the
Director of the Federal Register as of September 21, 2004.

FOR FURTHER INFORMATION CONTACT: William Botten, Access Board, 1331 F
Street NW., Suite 1000, Washington, DC 20004-1111. Telephone: (202)
272-0014 (voice) or (202) 272-0082 (TTY). Email address: board.gov">botten@access-board.gov.

SUPPLEMENTARY INFORMATION:

Table of Contents for Preamble

1. New Format for Guidelines
2. Executive Summary
3. Statutory and Regulatory Background
4. Changes Made to the Proposed Rule
5. Discussion of Scoping and Technical Requirements
6. Regulatory Analyses

In this preamble, ``we,'' ``our'' and ``us'' refer to the
Architectural and Transportation Barriers Compliance Board (Access
Board).

1. New Format for Guidelines

This final rule amends the Architectural Barriers Act Accessibility
Guidelines, which were published in the Federal Register on July 23,
2004 (69 FR 44151) and are codified in Appendices C and D to 36 CFR
part 1191. The guidelines were published as ``camera ready'' copy
(i.e., images) in 2004 because they included figures after certain
sections to illustrate technical requirements in the sections. Since it
is not possible to amend the guidelines as published in 2004, we
submitted the guidelines, as amended by the final rule, to the Federal
Register as a Word document without figures, except for four mandatory
symbols included at the end of Appendix D.\1\ The scoping requirements
for the Americans with Disabilities Act Accessibility Guidelines in
Appendix B are not changed. We did not include advisory sections that
previously appeared in Appendices B, C, and D because they provide
guidance only and do not contain mandatory requirements. We removed the
List of Figures and Index in Appendix E because it did not contain
regulatory material. We added notes to paragraphs (a) and (b) of
section 1191.1 that reference the accessibility standards adopted by
the Department of Justice and Department of Defense. Advisory sections
and figures are included in the documents on our Web page at:
www.access-board.gov.
---------------------------------------------------------------------------

\1\ The four mandatory symbols are the: Symbols to identify
elevator control buttons (Figure 407.4.7.13); International Symbol
of Accessibility (Figure 703.7.2.1); International Symbol of TTY
(Figure 703.7.2.2); and International Symbol of Access for Hearing
Loss (Figure 703.7.2.4).
---------------------------------------------------------------------------

2. Executive Summary

Legal Authority and Purpose

The Architectural Barriers Act requires facilities constructed or
altered by or on behalf of federal agencies to be readily accessible to
and usable by individuals with disabilities. Certain agencies are
required to adopt accessibility standards for the design, construction,
and alteration of facilities covered by the Architectural Barriers
Act.\2\ We are required by section 502 of the Rehabilitation Act to
establish and maintain minimum guidelines and requirements for the
accessibility standards adopted the federal agencies. We are issuing
the final rule pursuant to this authority. The final rule amends the
Architectural Barriers Act Accessibility Guidelines that we issued in
2004 to address camping facilities, picnic facilities, viewing areas,
trails, and beach access routes constructed or altered by or behalf of
federal agencies.
---------------------------------------------------------------------------

\2\ The Architectural Barriers Act requires the following
agencies to adopt accessibility standards: Department of Defense and
United States Postal Service for their facilities; Department of
Housing and Urban Development for residential facilities; and
General Services Administration for all other facilities.
---------------------------------------------------------------------------

Summary of Major Provisions

The final rule applies to the following federal agencies and their
components that administer outdoor areas developed for recreational
purposes: Department of Agriculture (Forest Service); Department of
Defense (Army Corps of Engineers); and Department of the Interior
(Bureau of Land Management, Bureau of Reclamation, Fish and Wildlife
Service, National Park Service). The final rule also applies to non-
federal entities that construct or alter recreation facilities on
federal land on behalf of the federal agencies pursuant to a concession
contract, partnership agreement, or similar arrangement.
The final rule adds scoping and technical requirements for the
design, construction, and alteration of camping facilities, picnic
facilities, viewing areas, trails, and beach access routes to the
Architectural Barriers Act Accessibility Guidelines. The scoping
requirements address the following outdoor constructed features
provided at these facilities: Picnic tables, fire rings, grills,
fireplaces, wood stoves, trash and recycling receptacles, water
hydrants, utility and sewage hookups, outdoor rinsing showers, benches,
and viewing scopes. The scoping requirements also address the following
elements provided in camping units with mobility features: Parking
spaces for recreational vehicles and other vehicles; tent pads and tent
platforms; and camp shelters. The scoping requirements added by the
final rule are summarized in Table 1.

[[Page 59477]]

Table 1--Scoping Requirements Added by Final Rule
------------------------------------------------------------------------

------------------------------------------------------------------------
F244 Camping Facilities.............. Requires minimum number of
F245 Picnic Facilities............... camping units and picnic units
to provide mobility features
based on total number of units
provided in the camping or
picnic facility.
Requires camping units and picnic
units with mobility features to
provide choices of units
comparable to, and integrated
with, those available to others.
Requires at least one of each
type of outdoor constructed
features and other elements
provided within camping units
and picnic units with mobility
features to comply with the
applicable technical
requirements. Where more than
one of the same type of outdoor
constructed feature or element
is provided, requires at least
two of the same type to comply
with the applicable technical
requirements.
Requires at least 20 percent of
each type of outdoor constructed
features provided at each
location in common use and
public use areas serving camping
units and picnic units with
mobility features to comply with
the applicable technical
requirements.
Requires outdoor recreation
access routes to connect:
Accessible elements,
spaces, and facilities provided
within camping units and picnic
units with mobility features;
Camping units and
picnic units with mobility
features to common use and public
use areas serving the units;
Accessible elements,
spaces, and facilities provided
within common use and public use
areas serving camping units and
picnic units with mobility
features; and
Camping units and
picnic units with mobility
features to an accessible route
serving adjacent recreation
facilities, where a circulation
path connects camping and picnic
facilities and adjacent
recreation facilities.
F246 Viewing Areas................... Requires each distinct viewing
location and at least 20 percent
of outdoor constructed features
within viewing areas to comply
with the applicable technical
requirements.
Requires outdoor recreation
access routes to connect
accessible parking spaces or
other arrival points serving the
viewing area with accessible
elements, spaces, and facilities
provided within the viewing
area.
F216.13 Trailhead Signs.............. Requires new trail information
F247 Trails.......................... signs provided at trailheads on
newly constructed and altered
trails designed for use by
hikers or pedestrians to comply
with the applicable technical
requirements for trailhead
signs.
Requires trails designed for use
by hikers and pedestrians to
comply with the applicable
technical requirements for
trails where the trail directly
connects to a trailhead or
another trail that substantially
meets the applicable technical
requirements for trails.
Requires existing trails to
comply with the applicable
technical requirements for
trails where the original
design, function, or purpose of
the trail is changed and the
altered portion of the trail
directly connects to a trailhead
or another trail that
substantially meets the
applicable technical
requirements for trails.
Requires camping facilities,
picnic facilities, and viewing
areas provided on trails to
comply with the applicable
scoping requirements in F244,
F245, and F246, except for
outdoor recreation access
routes.
Requires at least 20 percent of
outdoor constructed features
provided at trailheads and at
each location on trails, other
than at facilities provided on
trails, to comply with the
applicable technical
requirements.
Requires outdoor recreation
access routes to connect
accessible parking spaces or
other arrival points serving a
trailhead to the starting point
of the trail and accessible
elements, spaces, and facilities
provided within the trailhead.
F248 Beach Access Routes............. Requires at least one permanent
or removable beach access route
to be provided for each 1/2 mile
of beach shoreline administered
or managed by an entity where:
Circulation paths,
parking facilities, toilet
facilities, or bathing facilities
serving the beach are constructed
or altered; or
A beach nourishment
project is undertaken.
Not more than 20 percent of the
costs of constructing or
altering facilities serving the
beach or a beach nourishment
project are required to be
expended on beach access routes.
------------------------------------------------------------------------

The technical requirements establish design criteria for outdoor
constructed features; parking spaces within camping units and picnic
units with mobility features; pull-up spaces for recreational vehicles
at dump stations; tent pads and tent platforms; camp shelters; viewing
areas; outdoor recreation access routes; trails; and beach access
routes. The final rule permits exceptions to specific provisions in the
technical requirements for certain elements and facilities based on the
conditions listed in Table 2. When an entity determines that a
condition does not permit full compliance with a provision, compliance
is required to the extent practicable.

Table 2--Conditions for Exceptions
------------------------------------------------------------------------

------------------------------------------------------------------------
1................................. Compliance is not practicable due to
terrain.
2................................. Compliance cannot be accomplished
with the prevailing construction
practices.
3................................. Compliance would fundamentally alter
the function or purpose of the
facility or the setting.

[[Page 59478]]

4................................. Compliance is limited or precluded
by any of the following laws, or by
decisions or opinions issued or
agreements executed pursuant to any
of the following laws: Endangered
Species Act; National Environmental
Policy Act; National Historic
Preservation Act; Wilderness Act;
or other federal, state, or local
law the purpose of which is to
preserve threatened or endangered
species; the environment; or
archaeological, cultural,
historical, or other significant
natural features.
------------------------------------------------------------------------

The final rule allows exemptions for an entire trail or beach
access route when an entity determines that is impracticable for a
trail to comply with the technical requirements for trails or to
provide a beach access route complying with the technical requirements
for beach access routes. This determination is made after the entity
applies the exceptions for specific provisions in the technical
requirements for trails or beach access routes to portions of the trail
or route.

Summary of Costs and Benefits

We compared the final rule to guidelines and standards used by the
federal agencies for the design of outdoor developed areas without
regard to accessibility to determine whether the final rule would
result in additional costs. We determined the final rule would not
result in additional costs for camping facilities and picnic
facilities. We estimate the final rule would result in additional costs
for viewing areas, trails, and beach access routes shown in Table 3. We
estimate the federal agencies would incur $1.2 million additional
annual costs due to the final rule.

Table 3--Additional Costs Due to Final Rule
------------------------------------------------------------------------

------------------------------------------------------------------------
Viewing Areas..................... $2,176 for dual base binocular
scopes and $3,380 for a dual base
telescopes, if viewing scopes
provided at viewing areas.
Trails............................ $40,655 per trail mile, if trail
would not otherwise meet the
technical requirements and the
exceptions to the technical
requirements do not apply to the
trail.
Beach Access Routes............... $4,497 to $6,530 to purchase roll-
out mats for beach access routes,
if parking areas, toilet
facilities, bathing facilities, and
circulation paths serving beaches
are constructed or altered or beach
nourishment project is undertaken.
------------------------------------------------------------------------

The proposed rule would enable individuals with mobility
disabilities to participate in outdoor recreation activities with their
families and friends. The benefits are difficult to quantify, but
include important national values recognized in Executive Order 13563
such as equity, human dignity, and fairness.

3. Statutory and Regulatory Background

The Architectural Barriers Act requires facilities constructed or
altered by or on behalf of federal agencies to be readily accessible to
and usable by individuals with disabilities.\3\ See 42 U.S.C. 4151 et
seq. The Department of Defense, Department of Housing and Urban
Development, General Services Administration, and United States Postal
Service are required to adopt accessibility standards for the design,
construction, and alteration of facilities covered by the Architectural
Barriers Act.\4\ See 42 U.S.C. 4152 through 4154a. We are required by
section 502 of the Rehabilitation Act to establish and maintain minimum
guidelines and requirements for the accessibility standards adopted the
federal agencies. See 29 U.S.C. 792(b)(3). We also are required by
section 502 of the Rehabilitation Act to investigate complaints
alleging that facilities covered by the Architectural Barriers Act have
not complied with the accessibility standards. See 29 U.S.C. 792(b)(1)
and (e). When we find a violation, we request the responsible federal
agency to submit a corrective action plan and monitor implementation of
the plan.
---------------------------------------------------------------------------

\3\ The Architectural Barriers Act also covers facilities leased
by federal agencies; facilities financed by a federal grant or loan;
and facilities constructed by the Washington Metropolitan Area
Transit Authority. The final rule does not apply to these
facilities.
\4\ The Department of Defense and United States Postal Service
are required to adopt accessibility standards for their facilities;
the Department of Housing and Urban Development is required to adopt
accessibility standards for residential facilities; and the General
Services Administration is required to adopt accessibility standards
for all other facilities covered by the Architectural Barriers Act.
---------------------------------------------------------------------------

We issued the Architectural Barriers Act Accessibility Guidelines
for facilities covered by the Architectural Barriers Act in 2004. See
69 FR 44151 (July 23, 2004). The guidelines contain scoping and
technical requirements. Scoping requirements specify what features are
required to be accessible and, where multiple features of the same type
are provided, how many of the features are required to be accessible.
Technical requirements specify the design criteria for accessible
features. The scoping and technical requirements address some but not
all of the features provided at outdoor areas developed for recreation
purposes. For example, the scoping and technical requirements address
parking areas, toilet and bathing facilities, fishing piers and
platforms, and boating docks and marinas. However, the scoping and
technical requirements do not address the minimum number of camping
units and picnic units required to provide mobility features, or
provide design criteria for viewing areas, trails, and beach access
routes. The final rule amends the guidelines by adding scoping and
technical requirements for these features.
The Architectural Barriers Act Accessibility Guidelines are
codified at Appendices C and D to 36 CFR part 1191. The Department of
Defense, United States Postal Service, and General Services
Administration adopted the Architectural Barriers Act Accessibility
Guidelines as the accessibility standards for facilities covered by the
Architectural Barriers Act Guidelines by cross-referencing Appendices C
and D.\5\ Since these

[[Page 59479]]

agencies cross-reference Appendices C and D, the amendments to
Appendices C and D made by the final rule are incorporated into the
accessibility standards for facilities covered by the Architectural
Barriers Act. Thus, camping facilities, picnic facilities, viewing
areas, trails, and beach access routes constructed or altered by or on
behalf of federal agencies on or after the effective date of the final
rule are required to comply with Appendices C and D, as amended by the
final rule.
---------------------------------------------------------------------------

\5\ The Department of Defense cross references Appendices C and
D as the accessibility standards for its facilities in a Memorandum
on Access for People with Disabilities (October 31, 2008) at: https://www.access-board.gov/guidelines-and-standards/buildings-and-sites/about-the-aba-standards/background/dod-memorandum. The United States
Postal Service cross references Appendices C and D as the
accessibility standards for its facilities at 39 CFR 254.1. The
General Services Administration cross references Appendices C and D
as the accessibility standards for all other facilities, except
residential facilities, covered by the Architectural Barriers Act at
41 CFR 102-76.65. The Department of Housing and Urban Development
references the Uniform Federal Accessibility Standards, which was
issued in 1984, as the accessibility standards for residential
facilities covered by the Architectural Barriers Act. See 24 CFR
40.4.
---------------------------------------------------------------------------

The final rule does not apply to outdoor developed areas
administered by state and local governments and by private entities
covered by Titles II and III the Americans with Disabilities Act
because sufficient data were not available to prepare a regulatory
assessment of the impact of the proposed rule on state and local
governments or private entities. We will conduct a separate rulemaking
in the future for outdoor developed areas administered by state and
local governments and by private entities covered by the Titles II and
III of the Americans with Disabilities Act.\6\
---------------------------------------------------------------------------

\6\ We are required to establish and maintain minimum guidelines
and requirements for the accessibility standards adopted by the
Department of Justice and Department of Transportation for
facilities covered by Titles II and III of the Americans with
Disabilities Act. See 29 U.S.C. 792 (b)(3) and 42 U.S.C. 12204.
---------------------------------------------------------------------------

4. Changes Made to the Proposed Rule

We issued a proposed rule in 2007. See 72 FR 34074 (June 20, 2007).
The proposed rule was based on the report of a regulatory negotiation
committee. We released a draft of the final rule in 2009. The
regulatory negotiation report, proposed rule, and draft of the final
rule are available on our Web site at: https://www.access-board.gov/outdoor (click on Background). The changes made to the proposed rule
are discussed below.

Format and Organization

The proposed rule would have established the scoping and technical
requirements for camping facilities, picnic facilities, viewing areas,
trails, and beach access routes as separate guidelines to be codified
as an appendix to 36 CFR part 1195. The final rule incorporates the
scoping and technical requirements for these facilities into the
Architectural Barriers Act Accessibility Guidelines, which are codified
as Appendices C and D to 36 CFR part 1191.

Exceptions When Conditions Do Not Permit Full Compliance

The proposed rule would have permitted exceptions to only certain
provisions in the technical requirements when certain conditions do not
permit full compliance. The final rule restates the conditions as shown
in the Table 2 under the Executive Summary, and permits exceptions
based on the conditions to any provision in the technical requirements
for tent pads and tent platforms, camp shelters, viewing areas, outdoor
recreation access routes, trails, and beach access routes.\7\ The final
rule also permits exceptions based on the conditions to the provisions
for clear ground space at outdoor constructed features in alterations.
---------------------------------------------------------------------------

\7\ Exceptions are permitted to the technical requirements for
viewing areas and for outdoor recreation access routes at camping
facilities, picnic facilities, and trailheads only in alterations.
---------------------------------------------------------------------------

The proposed rule would have required compliance ``to the maximum
extent feasible'' when an exception is used. The final rule requires
compliance ``to the extent practicable'' when an exception is used.
This language is more in keeping with the regulatory negotiation
committee report, which considered the term ``feasible'' to mean
``reasonably-doable.'' The regulatory negotiation committee report used
the example of constructing a portion of a trail in a steeply sloped
area, where complying with the provision for running slope would
require extensive cuts and fills that would be difficult to construct
and maintain; cause drainage and erosion problems; and have a severe
impact on the environment. In this example, the portion of the trail
constructed in the steeply sloped area is permitted to comply with the
provision for running slope to the extent practicable.
When an exception to a specific provision in the technical
requirements is used on a portion of a trail or beach access route, the
final rule requires the federal agency to document the basis for its
determination to use the exception and to maintain the documentation in
the records for the trail or beach project in the event that a
complaint is later filed alleging that the trail or beach access route
does not fully comply with the applicable technical requirements. When
investigating the complaint, we will request the federal agency to
provide the documentation if the federal agency claims that it used an
exception based on the conditions.

Exemptions for Entire Trail or Beach Access Route

The proposed rule would have exempted an entire trail from
complying with the technical requirements for trails when:
The combination of running slope and cross slope exceeds
40 percent for over 20 feet;
A trail obstacle 30 inches high or more runs across the
full tread width of the trail;
The trail surface is neither firm nor stable for a
distance of 45 feet or more;
The tread width is less than 12 inches wide for a distance
of 20 feet or more; or
The trail is not required to comply with any of the
technical requirements for more than 15 percent of the trail.
The final rule allows an entire trail to be exempted when an entity
determines that it would be impracticable for the trail to comply with
the technical requirements for trails. This determination is made after
the entity applies the exceptions for specific provisions in the
technical requirements for trails to portions of the trail. The
exemption is intended to allow for conditions in the field other than
those listed in the proposed rule that may render it impracticable for
the trail to comply with the technical requirements for trails. The
final rule requires federal agencies to notify us if an entire trail is
exempted. A form to notify us is available at: https://www.access-board.gov/outdoor. The form lists the conditions in the proposed rule
as a basis for exempting an entire trail and allows other conditions in
the field to also be a basis for exempting an entire trail. The form
will allow us to monitor exemptions and to provide guidance as
necessary.
The proposed rule did not include an exemption for an entire beach
access route. The final rule does not require a beach access route to
be provided when an entity determines that it would be impracticable to
provide a beach access route complying with the technical provisions
for beach access routes. This determination is made after the entity
applies the exceptions for specific provisions in the technical
requirements for beach access routes to portions of the route. The
final rule requires federal agencies to notify us if a beach access
route is not provided. A form to notify us is available at: https://www.access-board.gov/guidelines-and-standards/recreation-facilities/outdoor-developed-areas.

Beach Access Routes

The proposed rule would have required beach access routes to be

[[Page 59480]]

provided where a beach is constructed and where a pedestrian route is
constructed at a beach. The final rule requires beach access routes to
be provided where the entity that administers or manages a beach
constructs or alters circulation paths, parking facilities, toilet
facilities, or bathing facilities to serve the beach or undertakes a
beach nourishment project. The entity is not required to expend more
than 20 percent of the costs of constructing or altering facilities
serving the beach or the beach nourishment project to provide beach
access routes.
The proposed rule would have required the clear width of beach
access routes to be 36 inches minimum. Beach access routes provide a
firm and stable surface over the sand and are used by beach visitors
with and without disabilities. The final rule requires the clear width
of beach access routes to be 60 inches minimum to enable individuals
who use wheeled mobility devices to pass beach visitors traveling in
the opposite direction.

Shared Use Paths

The preamble to the proposed rule indicated that the proposed
scoping and technical requirements for trails would apply to shared use
paths. A shared use path is a multi-use path that is designed primarily
for use by pedestrians and bicyclists for transportation and
recreational purposes. Shared use paths are physically separated from
motor vehicle traffic by an open space or barrier, and are either
within the highway right-of-way or within an independent right-of-way.
We subsequently decided to include shared use paths in the proposed
accessibility guidelines for pedestrian facilities in the public right-
of-way. See 78 FR 10110 (February 13, 2013).

Trailhead Signs

The proposed rule would have required signs to be provided at
trailheads to identify accessible trails. The proposed rule would have
required the signs to include information on the total distance of the
trail and, where exceptions have been used, the location of the first
point where the trail does not fully comply with the technical
requirements for trails.
Where new trail information signs are provided at trailheads on
newly constructed or altered trails designed for use by hikers or
pedestrians, the final rule requires the signs to include information
on the length of the trail or trail segment; surface type; typical and
minimum tread width; typical and maximum running slope; and typical and
maximum cross slope. This requirement applies regardless of whether the
trail complies with the technical requirements for trails. The
information provided on the signs enables individuals with disabilities
to decide whether to hike the trail based on the characteristics of the
trail.

Surface Slopes

The proposed rule would have required clear ground spaces to have
slopes not steeper than 1:50 in any direction, and would have permitted
slopes not steeper than 1:33 when necessary for drainage. The final
rule requires clear ground spaces to have slopes not steeper than 1:48
in any direction and, where the surface is other than concrete,
asphalt, or boards, permits slopes not steeper than 1:20 when necessary
for drainage. The final rule defines the term boards to include wood,
plastic, metal, and composite products.
The proposed rule would have required outdoor recreation access
routes and beach access routes to have cross slopes not steeper than
1:33, and would have permitted cross slopes not steeper than 1:20 when
necessary for drainage. The proposed rule would have required trails to
have cross slopes not steeper than 1:20. The final rule requires
outdoor recreation access routes, trails, and beach access routes to
have cross slopes not steeper than 1:48 and, where the surface is other
than concrete, asphalt, or boards, permits cross slopes not steeper
than 1:20 when necessary for drainage.

Outdoor Constructed Features

The proposed rule contained separate scoping and technical
requirements for picnic tables, fire rings, grills, fireplaces, wood
stoves, trash and recycling receptacles, water hydrants, utility and
sewage hookups, outdoor rinsing showers, benches, and viewing scopes.
The final rule collectively defines these elements as outdoor
constructed features.
The proposed rule would have required 50 percent of picnic tables,
fire rings, grills, and benches to comply with the applicable technical
requirements, and would have required at least 40 percent of these
elements that complied with the applicable technical requirements to be
on an outdoor recreation access route. In the final rule, the scoping
requirements for camping facilities, picnic facilities, viewing areas,
trailheads, and trails include scoping requirements for outdoor
constructed features; and the technical requirements for outdoor
constructed features are contained in 1011. The final rule requires
every outdoor constructed feature that complies with the applicable
technical requirements in 1011 to be on an outdoor recreation access
route.
The proposed rule based the size of the clear ground space at
outdoor constructed features on the dimensions for clear floor or
ground surfaces in 305.2 of the Architectural Barriers Act
Accessibility Guidelines. The final rule bases the size of the clear
ground space at outdoor constructed features on the dimensions for
maneuvering clearance at clear floor or ground spaces that are confined
on all or part of three sides in 305.7 of the Architectural Barriers
Act Accessibility Guidelines. Outdoor constructed features can be
confined on all or part of three sides by surfaces that are not firm
and stable or that have changes in level. The dimensions for
maneuvering clearance at clear floor or ground spaces that are confined
on all or part of three sides in 305.7 of the Architectural Barriers
Act Accessibility Guidelines provide additional space for maneuvering
into and out of the space: 36 inches minimum by 48 inches minimum for a
forward approach, and 30 inches minimum by 60 inches minimum for a
parallel approach. At water hydrants, a clear ground space for a
forward approach is required on each side of the water hydrant to
enable individuals with disabilities to operate the water hydrant from
their right side or left side. At rinsing showers, the size of the
clear ground space is based on the dimensions for turning space in
304.3.1 of the Architectural Barriers Act Accessibility Guidelines to
enable individuals with disabilities to turn in the space.
The proposed rule would have required outdoor rinsing showers to
provide grab bars. Outdoor rinsing showers typically are provided at
beaches for rinsing off sand and lotions that people apply to their
bodies when they are outdoors. They are not designed for bathing and do
not offer privacy. Individuals who use wheeled mobility devices are not
expected to transfer from the devices when using outdoor rinsing
showers and do need grab bars for this purpose. Therefore, the final
rule does not require grab bars at rinsing showers.
The proposed rule also would have required outdoor rinsing showers
to provide a fixed shower head at a lower height. The final rule
requires outdoor rinsing showers to provide a hand-held shower spray
unit that has at least one fixed position located 15 inches minimum and
48 inches maximum above the ground. Where vandalism is a consideration,
a fixed shower head located 48 inches above the ground is

[[Page 59481]]

permitted in place of a hand-held shower spray unit.
The proposed rule would have required benches to provide a backrest
and armrests. The final rule does not require a backrest and armrests
due to the varied designs and configurations of benches.

Elements Exempted in Final Rule

The proposed rule included proposed scoping and technical
requirements for utility sinks and pit toilets. The final rule exempts
these elements from the scoping requirements in F212.3 and F213.1 of
the Architectural Barriers Act Accessibility Guidelines.

Elements Not Addressed in Final Rule

The proposed rule included proposed scoping and technical
requirements for recreational vehicle parking spaces in general parking
areas at camping facilities. The final rule includes scoping and
technical requirements for recreational vehicle parking spaces in
camping units with mobility features and recreational vehicle pull-up
spaces at dump stations. The final rule does not address recreational
vehicle parking spaces in other areas.
The proposed rule included proposed scoping and technical
requirements for mobility device storage facilities and warming huts.
The final rule does not address these elements because they are not
typically provided at the facilities addressed in the final rule.

5. Discussion of Scoping and Technical Requirements

The scoping and technical requirements in the final rule are
discussed below.

Appendix C to 36 CFR Part 1191--Architectural Barriers Act: Scoping

ABA Chapter 1: Application and Administration
F106.5 Defined Terms
The final rule adds definitions to this section for the following
terms: boards, camp shelter, camping facility, camping unit, outdoor
constructed features, picnic facility, picnic unit, trail, trailhead,
and viewing areas. The definition of boards is discussed above under
the Executive Summary. The definition of outdoor constructed features
is discussed above under Changes Made to the Proposed Rule. The
definitions of the other terms are discussed below under the sections
where the terms are used.
ABA Chapter 2: Scoping Requirements
F201.4 Requirements Apply to Facilities Constructed or Altered by or on
Behalf of Federal Agencies
This section provides that the scoping requirements in F216.13 and
F244 though F248 and the technical requirements in 1011 through 1019
apply to camping facilities, picnic facilities, viewing areas, trails,
and beach access routes constructed or altered by federal agencies or
by non-federal entities on federal land on behalf of federal agencies
pursuant to a concession contract, partnership agreement, or similar
arrangement.
F201.4.1 Documentation and Notification When Exceptions Used for Trails
or Beach Access Routes
This section requires federal agencies to document the basis for
not fully complying with a specific provision in the technical
requirements for trails on a portion of a trail based on Exception 1 in
1017, or with a specific provision in the technical requirements for
beach access routes based on Exception 1 in 1018. Federal agencies are
required to maintain the documentation with the records for the trail
or beach project. The section also requires federal agencies to notify
us if an entire trail is exempted from complying with the technical
requirements for trails based on Exception 2 in 1017, and if a beach
access route is not provided based on Exception 2 in 1018. Notification
forms are available on our Web site at: https://www.access-board.gov/outdoor.
F202.3 Alterations
The final rule adds Exception 4 to this section, which applies to
altered elements and spaces. Exception 4 does not require an outdoor
recreation access route to altered elements and spaces in camping
facilities, picnic facilities, viewing areas, or trailheads where the
circulation path to the altered element or space is not altered.
Exception 4 is consistent with Exception 1 to this section, which does
not require an accessible route to altered elements and spaces in other
types of facilities where the circulation path to the altered element
or space is not altered, unless the alterations affect primary function
areas.
F202.4 Alterations Affecting Primary Function Areas
The final rule adds Exception 2 to this section, which applies to
altered areas containing a primary function. Exception 2 exempts
camping facilities, picnic facilities, viewing areas, trailheads,
trails, and beach access routes from providing an accessible path of
travel to altered areas containing a primary function. The regulations
and policies issued by the federal agencies referenced in the section
define an accessible path of travel as an accessible route. Exception 4
is added because the final rule does not require accessible routes at
camping facilities, picnic facilities, viewing areas, and trailheads
where outdoor recreation access routes are provided. The final rule
also does not require accessible routes where camping facilities,
picnic facilities, and viewing areas are provided on trails and where
beach access routes are provided.
F206.1 General
The final rule adds three exceptions to this section, which
contains the scoping requirements for accessible routes. Exception 1
does not require accessible routes at camping facilities, picnic
facilities, viewing areas, and trailheads where outdoor recreation
access routes are provided. Exception 2 does not require accessible
routes where camping facilities, picnic facilities, viewing areas, and
outdoor constructed features are provided on trails. Exception 3 does
not require accessible routes where beach access routes are provided.
F212.3 Sinks
The final rule adds Exception 2 to this section, which contains the
scoping requirements for sinks. Exception 2 exempts sinks in camping
facilities and picnic facilities where a cooktop or conventional range
is not provided. Exception 2 applies to utility sinks used to clean
large pots and equipment. Exception 2 is consistent with Exception 1 to
this section, which exempts service sinks because they cannot comply
with technical requirements for sinks due to their configuration.
Utility sinks used to clean large pots and equipment are configured
similar to service sinks. Lavatories (i.e., sinks in toilet and bathing
facilities) are not affected by Exception 2.
F213.1 General
The final rule adds an exception to this section, which contains
the scoping requirements for toilet facilities. The exception exempts
pit toilets provided on trails and in camping facilities. A pit toilet
is a primitive outhouse consisting of a toilet riser over a hole dug
into the ground or receptacle to receive and naturally decompose human
waste. Some pit toilets do not have walls and would not be able to
comply with the technical requirements for toilet facilities such as
providing grab bars at

[[Page 59482]]

toilet fixtures. However, the technical requirements for toilet
facilities can be used as guidance for designing pit toilets.
F216.13 Trailhead Signs
Where new trail information signs are provided at trailheads on
newly constructed or altered trails designed for use by hikers or
pedestrians, this section requires the signs to comply with the
technical requirements in 1017.11, regardless of whether the trails
comply with the technical requirements in 1017. The technical
requirements in 1017.11 require the signs to include information on the
length of the trail or trail segment; surface type; typical and minimum
tread width; typical and minimum running slope; and typical and minimum
cross slope. This information enables individuals with disabilities to
decide whether to hike the trail based on the characteristics of the
trail. Entities should also provide information about the accessibility
of trails on Web sites.
If trail information signs designate the name of the trail, only
the name of the trail is required to comply with the technical
requirements in 703.5. See F216.2. Tactile characters are not required
on exterior signs. Trail information signs are not required to display
the International Symbol of Accessibility.
F244 Camping Facilities
F244.1 General
This section contains the scoping requirements for camping
facilities, other than camping facilities on trails. The scoping
requirements for camping facilities on trails are contained in
F247.4.1. The terms camping facility, camping unit, and camp shelter
are defined in F106.5. A camping facility is a site, or a portion of a
site, developed for outdoor recreational purposes that contains camping
units. A camping unit is an outdoor space in a camping facility used
for camping that contains outdoor constructed features, parking spaces
for recreational vehicles or other vehicles, tent pads or tent
platforms, or camp shelters. A camp shelter is a partially enclosed
structure that provides campers and hikers cover from weather and that
does not contain plumbing fixtures or kitchen appliances. Camp shelters
are not transient lodging facilities or residential dwelling units.
F244.2 Camping Units With Mobility Features
This section requires camping facilities to provide a minimum
number of camping units with mobility features based on the total
number of camping units in accordance with Table 244.2. Where different
types of camping units are provided (e.g., camping units for
recreational vehicles only; camping units for tent camping only; and
camping units with camp shelters), Table 244.2 applies to each type of
camping unit provided.
Camping units with mobility features are not required to be
identified by signs. Entities should provide information on the
location of camping units with mobility features on Web sites, in
brochures, and at bulletin boards or information kiosks at the camping
facility. Where entities operate reservation systems for camping units
or assign camping units upon arrival, entities should establish
policies to ensure that camping units with mobility features are
available for individuals with disabilities until all the camping units
are occupied.
F244.2.1 Alterations and Additions
This section requires camping units that are altered or added to
provide mobility features until the number of camping units with
mobility features in the camping facility meets the minimum number
required in Table 244.2.
Where an entity is implementing a transition plan for program
accessibility developed pursuant to regulations issued under section
504 of the Rehabilitation Act that designates specific camping units to
provide mobility features, an exception permits the entity to not
provide accessible elements when altering individual elements within
camping units that are not designated to provide mobility features.
When all the elements within a camping unit are altered, the altered
camping unit is required to provide mobility features until the minimum
number of camping units with mobility features required in Table 244.2
is met.
F244.2.2 Dispersion
This section requires camping units with mobility features to
provide choices of camping units comparable to, and integrated with,
those available to others.
F244.2.3 Elements Within Camping Units With Mobility Features
This section contains the scoping requirements for elements within
camping units required to provide mobility features, including outdoor
constructed features (F244.2.3.1), parking spaces for recreational
vehicles (F244.2.3.2.1), parking spaces for vehicles other than
recreational vehicles (F244.2.3.2.2), tent pads and tent platforms
(F244.2.3.3), and camp shelters (F244.3.4). Where these elements are
provided within a camping unit, at least one of each type of element is
required to comply with the applicable technical requirements for the
element. Where more than one of the same element is provided within a
camping unit (e.g., picnic tables, tent pads), at least two of the same
type element are required to comply with the applicable technical
requirements for the element.
F244.3 Outdoor Constructed Features in Common Use and Public Use Areas
This section contains the scoping requirements for outdoor
constructed features provided in common use and public use areas that
serve camping units with mobility features. At least 20 percent, but
not less than one, of each type of outdoor constructed feature provided
at each location is required to comply with the applicable technical
requirements in 1011.
F244.4 Pull-up Spaces for Recreational Vehicles at Dump Stations
This section requires pull-up spaces provided for recreational
vehicles at dump stations to comply with the applicable technical
requirements in 1012.
F244.5 Outdoor Recreation Access Routes
This section contains the scoping requirements for outdoor
recreation access routes at camping facilities, which are discussed
below.
F244.5.1 Routes Within Camping Units With Mobility Features
This section requires at least one outdoor recreation access route
to connect accessible elements, spaces, and facilities provided within
camping units with mobility features.
F244.5.2 Routes to and Within Common Use and Public Use Areas
This section requires at least one outdoor recreation access route
to connect each camping unit with mobility features with common use and
public use areas serving the unit; and at least one outdoor recreation
access route to connect accessible elements, spaces, and facilities
provided within common use and public use areas serving camping units
with mobility features. An outdoor recreation access route is not
required to connect camping units with mobility features and
recreational vehicle dump stations where a pull-up space complying with
the applicable technical requirements in 1012 is provided at the dump
station for recreational vehicles.

[[Page 59483]]

F244.5.3 Routes to Adjacent Recreation Facilities
Where a circulation path connects camping facilities and adjacent
recreation facilities, this section requires at least one outdoor
recreation access route to connect camping units with mobility features
to an accessible route serving the adjacent recreation facilities. The
section does not modify the scoping requirements for accessible routes
in F206 of the Architectural Barriers Act Accessibility Guidelines that
apply to recreation facilities.
F244.5.4 Location
This section requires outdoor recreation access routes to coincide
with or be located in the same general area as general circulation
paths. Where a vehicular way serves as the general circulation path for
pedestrians at a camping facility, the outdoor recreation access route
can be provided within the vehicular way.
F245 Picnic Facilities
F245.1 General
This section contains the scoping requirements for picnic
facilities, other than picnic facilities on trails. The scoping
requirements for picnic facilities on trails are contained in F247.4.2.
The terms picnic facility and picnic unit are defined in F106.5. A
picnic facility is a site, or a portion of a site, developed for
outdoor recreational purposes that contains picnic units. A picnic unit
is an outdoor space in a picnic facility used for picnicking that
contains outdoor constructed features.
F245.2 Picnic Units With Mobility Features
This section requires picnic facilities to provide a minimum number
of picnic units with mobility features as discussed below. Picnic units
with mobility features are not required to be identified by signs.
Entities should provide information on the location of picnic units
with mobility features on Web sites, in brochures, and at bulletin
boards or information kiosks at the picnic facility.
F245.2.1 Picnic Facilities With Two or Fewer Picnic Units
Where picnic facilities contain two or fewer picnic units, this
section requires each picnic unit to provide mobility features.
F245.2.2 Picnic Facilities With More Than Two Picnic Units
Where picnic facilities contain more than two picnic units, this
section requires at least 20 percent, but not less than two, of the
picnic units to provide mobility features.
F245.2.3 Alterations and Additions
This section requires picnic units that are altered or added to
provide mobility features until the number of picnic units with
mobility features in the picnic facility meets the minimum number
required in F245.2.1 or F245.2.2.
Where an entity is implementing a transition plan for program
accessibility developed pursuant to regulations issued under section
504 of the Rehabilitation Act that designates specific picnic units to
provide mobility features, an exception permits the entity to not
provide accessible elements when altering individual elements within
picnic units that are not designated to provide mobility features. When
all the elements within a picnic unit are altered, the altered picnic
unit is required to provide mobility features until the minimum number
of picnic units with mobility features required in F245.2.1 or F245.2.2
is met.
F245.2.4 Dispersion
This section requires picnic units with mobility features to
provide choices of picnic units comparable to, and integrated with,
those available to others.
F245.2.5 Elements Within Picnic Units With Mobility Features
This section contains the scoping requirements for elements within
picnic units required to provide mobility features, including outdoor
constructed features (F244.2.5.1) and parking spaces (F244.2.5.2).
Where these elements are provided within a picnic unit, at least one of
each type of element is required to comply with the applicable
technical requirements for the element. Where more than one of the same
element is provided within a picnic unit (e.g., picnic tables, grills),
at least two of the same type of element are required to comply with
the applicable technical requirements for the element.
F245.3 Outdoor Constructed Features in Common Use and Public Use Areas
This section contains the scoping requirements for outdoor
constructed features provided in common use and public use areas that
serve picnic units with mobility features. At least 20 percent, but not
less than one, of each type of outdoor constructed feature provided at
each location is required to comply with the applicable technical
requirements in 1011.
F245.4 Outdoor Recreation Access Routes
This section contains the scoping requirements for outdoor
recreation access routes within picnic facilities, which are discussed
below.
F245.4.1 Routes Within Picnic Units With Mobility Features
This section requires at least one outdoor recreation access route
to connect accessible elements, spaces, and facilities provided within
picnic units with mobility features.
F245.4.2 Routes to and Within Common Use and Public Use Areas
This section requires at least one outdoor recreation access route
to connect each picnic unit with mobility features with common use and
public use areas serving the unit; and at least one outdoor recreation
access route to connect accessible elements, spaces, and facilities
provided within common use and public use areas serving picnic units
with mobility features.
F245.4.3 Routes to Adjacent Recreation Facilities
Where a circulation path connects picnic facilities and adjacent
recreation facilities, this section requires at least one outdoor
recreation access route to connect picnic units with mobility features
to an accessible route serving the adjacent recreation facilities. The
section does not modify the scoping requirements for accessible routes
in F206 of the Architectural Barriers Act Accessibility Guidelines that
apply to recreation facilities.
F245.4.4 Location
This section requires outdoor recreation access routes to coincide
with or be located in the same general area as general circulation
paths. Where a vehicular way serves as the general circulation path for
pedestrians at a picnic facility, the outdoor recreation access route
can be provided within the vehicular way.
F246 Viewing Areas
F246.1 General
This section contains the scoping requirements for viewing areas,
other than viewing areas on trails. The scoping requirements for
viewing areas on trails are contained in F247.4.3. The term viewing
area is defined in F106.5 as an outdoor space developed for viewing a
landscape, wildlife, or other points of interest.
F246.2 Distinct Viewing Locations
This section requires each distinct viewing location within a
viewing area

[[Page 59484]]

to comply with the technical requirements for viewing areas in 1015.
Viewing areas can provide more than one distinct viewing location. For
example, a viewing area can provide a distinct viewing location for
observing a mountain range, and another distinct viewing location for
observing a river. Distinct viewing locations within a viewing area can
be designated by signs or other markers.
F246.3 Outdoor Constructed Features
This section requires at least 20 percent, but not less than one,
of each type of outdoor constructed feature provided within viewing
areas to comply with the applicable technical requirements in 1011.
F246.4 Outdoor Recreation Access Routes
This section requires at least one outdoor recreation access route
to connect accessible parking spaces or other site arrival points
serving the viewing area with accessible elements, spaces, and
facilities provided within the viewing area.
F247 Trails
F247.1 General
This section contains the scoping requirements for trails. The
terms trail and trailhead are defined in F106.5. A trail is a
pedestrian route developed primarily for outdoor recreational purposes.
A pedestrian route developed primarily to connect elements, spaces, and
facilities within a site is not a trail. A trailhead is an outdoor
space that is designated by an entity responsible for administering or
maintaining a trail to serve as an access point to the trail. The
junction of two or more trails or the undeveloped junction of a trail
and a road is not a trailhead.
Where a trail is designed for use by hikers or pedestrians and
directly connects to a trailhead or another trail that substantially
meets the technical requirements for trails in 1017, the section
requires the trail to comply with the technical requirements for trails
in 1017. The Federal Trail Data Standards classify trails by their
designed use and managed use.\8\ A trail has only one designed use that
determines the design, construction, and maintenance parameters for the
trail. A trail can have more than one managed use based on a management
decision to allow other uses on the trails. Trails that have a designed
use for hikers or pedestrians are required to comply with the technical
requirements for trails in 1017. Trails that have a designed use for
other than hikers or pedestrians are not required to comply with the
technical requirements for trails in 1017.
---------------------------------------------------------------------------

\8\ The Federal Trail Data Standards are available at: https://www.fgdc.gov/standards/projects/FGDC-standards-projects/trail-data-standard/.
---------------------------------------------------------------------------

A trail system may include a series of connecting trails. Only
trails that directly connect to a trailhead or another trail that
substantially meets the technical requirement for trails in 1017 are
required to comply with the technical requirements for trails in 1017.
F247.2 Existing Trails
Where the original design, function, or purpose of an existing
trail is changed and the altered portion of the trail directly connects
to a trailhead or another trail that substantially meets the technical
requirements for trails in 1017, this section requires the altered
portion of the trail to comply with the technical requirements for
trails in 1017. Routine or periodic maintenance activities that are
performed to return an existing trail to the condition to which the
trail was originally designed are not required to comply with the
technical requirements for trails in 1017.
F247.3 Trailheads
This section requires at least 20 percent, but not less than one,
of each type of outdoor constructed feature provided within trailheads
to comply with the applicable technical requirements in 1011. The
section also requires at least one outdoor recreation access route to
connect accessible parking spaces or other site arrival points serving
the trailhead; the starting point of the trail; and accessible
elements, spaces, and facilities provided within the trailhead.
F247.4 Trail Facilities
This section requires camping facilities, picnic facilities, and
viewing areas provided on trails to comply with the applicable scoping
requirements for the facilities in F244 through F246, except for the
scoping requirements for outdoor recreation access routes. The
facilities are required to comply with the applicable scoping
requirements regardless of whether the trail complies with the
technical requirements for trails in 1017.
The section requires routes that connect trails complying with the
technical requirements for trails in 1017 to camping facilities, picnic
facilities, viewing areas, pit toilets, and accessible elements within
the facilities to comply with the technical requirements for trails in
1017. Routes that connect trails that do not comply with the technical
requirements for trails in 1017 to these facilities and accessible
elements provided within the facilities are not required to comply with
the technical requirements for trails in 1017.
F247.5 Outdoor Constructed Features
This section requires at least 20 percent, but not less than one,
of each type of outdoor constructed feature provided at each location
on trails, other than within facilities provided on trails, to comply
with the applicable technical requirements in 1011.
F248 Beach Access Routes
F248.1 General
This section contains the scoping requirements for beach access
routes. Where the entity that administers or manages a beach constructs
or alters circulation paths, parking facilities, toilet facilities, or
bathing facilities to serve the beach or undertakes a beach nourishment
project, the section requires the entity to provide beach access
routes. The entity is not required to expend more than 20 percent of
the costs to construct or alter the facilities serving the beach or the
beach nourishment project to provide beach access routes. Beach access
routes can be permanent or removable. Removable beach access routes can
be moved to a protected storage area during storms and other periods
when the routes are subject to damage or loss. Beach access routes are
not required where pedestrian access to the beach is not permitted.
F248.2 Minimum Number
This section requires at least one beach access route to be
provided for each \1/2\ mile of beach shoreline administered or managed
by the entity. The number of beach access routes is not required to
exceed the number of pedestrian access points provided by the entity to
the beach. Pedestrian access points to a beach include parking
facilities that serve beaches, dune crossings, and stairways or ramps
leading from boardwalks to the beach.
F248.3 Location
This section requires beach access routes to coincide with or be
located in the same general area as pedestrian access points to the
beach.

Appendix D to 36 CFR Part 1191--Technical

Chapter 10: Recreation Facilities
The final rule adds technical requirements to Chapter 10 for
outdoor constructed features (1011); parking spaces within camping
units and picnic units and pull-up spaces at dump stations (1012); tent
pads and tent

[[Page 59485]]

platforms (1013); camp shelters (1014); viewing areas (1015); outdoor
recreation access routes (1016); trails (1017); and beach access routes
(1018). The final rule also adds the conditions for using the
exceptions to the specific provisions in these technical requirements
at 1019.
1011 Outdoor Constructed Features
1011.1 General
This section contains the technical requirements for outdoor
constructed features provided within camping facilities, picnic
facilities, viewing areas, and trailheads or on trails. All outdoor
constructed features are required to comply with the provisions for
clear ground space (1011.2) and operable parts (1011.3). The section
includes specific provisions for picnic tables (1011.4); fire rings,
grills, fireplaces, and woodstoves (1011.5); water spouts at water
hydrants and water utility hook-ups (1011.6); outdoor rinsing showers
(1011.7); and viewing scopes (1011.8).
1011.2 Clear Ground Space
This section requires a clear ground space to be provided at
outdoor constructed features and includes specific provisions for the
size and location (1011.2.1), surface (1011.2.2), slope (1011.2.3), and
openings (1011.2.4).
Two exceptions are provided. Where individual outdoor constructed
features are altered and the ground surface is not altered, Exception 1
does not require the clear ground space to comply with the specific
provisions for surface and slope. In alterations, when an entity
determines that a condition in 1019 does not permit full compliance
with a specific provision, Exception 2 permits the clear ground space
to comply with the provision to the extent practicable.
1011.2.1 Size and Location
This section specifies the size and location of the clear ground
space at outdoor constructed features. The size of the clear ground
space is based on the dimensions for maneuvering clearance at clear
floor or ground spaces that are confined on all or part of three sides
in 305.7 of the Architectural Barriers Act Accessibility Guidelines.
Outdoor constructed features can be confined on all or part of three
sides by surfaces that are not firm and stable or that have changes in
level. The dimensions for maneuvering clearance at clear floor or
ground spaces that are confined on all or part of three sides in 305.7
of the Architectural Barriers Act Accessibility Guidelines provide
additional space for maneuvering into and out of the space: 36 inches
minimum by 48 inches minimum for a forward approach, and 30 inches
minimum by 60 inches minimum for a parallel approach. At water
hydrants, a clear ground space for a forward approach is required on
each side of the water hydrant to enable individuals with disabilities
to operate the water hydrant from their right side or left side. At
rinsing showers, the size of the clear ground space is based on the
dimensions for turning space in 304.3.1 of the Architectural Barriers
Act Accessibility Guidelines to enable individuals with disabilities to
turn in the space.
At picnic tables, fire rings, grills, fireplaces, and woodstoves, a
clear ground space is required on all usable sides of the element. The
usable sides of these elements are the sides that can be used for
eating or serving food, building a fire, or cooking. All sides of
picnic tables are generally usable, unless the picnic table is placed
against a rock or tree that renders the side against the rock or tree
not usable. All sides of fire rings and grills are generally usable,
unless there is a wall or other structure on a side that renders the
side not usable. The front sides of fireplaces and woodstoves are
generally the usable side.
1011.2.2 Surface
This section requires the surface of the clear ground space to be
firm and stable.
1011.2.3 Slope
This section requires the slope of the clear ground space to not be
steeper than 1:48 in any direction. Where the surface is other than
asphalt, concrete, or boards, slopes not steeper than 1:20 are
permitted when necessary for drainage.
1011.2.4 Openings
This section requires openings in the clear ground space such as
drainage grates to not allow passage of a sphere more than \1/2\ inch
in diameter. Where possible, drainage grates should be located outside
of the clear ground space. Elongated openings should be placed so that
the long dimension is perpendicular, or as close to perpendicular as
possible, to the dominant direction of travel.
1011.3 Operable Parts
This section requires operable parts of outdoor constructed
features to comply with the technical requirements for the height of
operable parts in 309.3 of the Architectural Barriers Act Accessibility
Guidelines, which require operable parts to be placed within the reach
ranges specified in 308 of the Architectural Barriers Act Accessibility
Guidelines; and the technical requirements for operation in 309.4 of
the Architectural Barriers Act Accessibility Guidelines, which require
operable parts to be operable with one hand without tight grasping,
pinching, or twisting of the wrist and with not more than 5 pounds
force.
Four exceptions are provided. Exception 1 requires fire rings,
grills, fireplaces, wood stoves, water hydrants, and water utility
hook-ups to comply with the technical requirements for operation in
309.4 of the Architectural Barriers Act Accessibility Guidelines to the
extent practicable. Exception 2 requires trash and recycling
receptacles with hinged lids and controls to keep out large animals to
comply with the technical requirements for operation in 309.4 of the
Architectural Barriers Act Accessibility Guidelines to the extent
practicable. Exception 3 exempts dumpster type trash and recycling
receptacles from complying with the technical requirements for the
height of operable parts in 309.3 of the Architectural Barriers Act
Accessibility Guidelines and the technical requirements for operation
in 309.4 of the Architectural Barriers Act Accessibility Guidelines.
Exception 4 exempts sewage hatches from complying with the technical
requirements for the height of operable parts in 309.3 of the
Architectural Barriers Act Accessibility Guidelines and the technical
requirements for operation in 309.4 of the Architectural Barriers Act
Accessibility Guidelines.
New products may be developed with operable parts that comply with
the technical requirements for operation in 309.4 of the Architectural
Barriers Act Accessibility Guidelines. As products that comply with the
technical requirements for operation in 309.4 of the Architectural
Barriers Act Accessibility Guidelines become available, entities should
provide these products to enable individuals with disabilities to
operate them.
1011.4 Picnic Tables
This section requires picnic tables to comply with the technical
requirements for dining surfaces in 902.3 of the Architectural Barriers
Act Accessibility Guidelines, which requires the tops of dining
surfaces to be 28 inches minimum and 34 inches maximum above the
ground. The section also requires at least one wheelchair space to be
provided for each 24 linear feet of usable picnic table surface
perimeter. Wheelchair spaces are required to be 30 inches minimum by 48
inches minimum; be positioned for a forward

[[Page 59486]]

approach to the table; and provide knee and toe clearance complying
with 306 of the Architectural Barriers Act Accessibility Guidelines
under the table.
1011.5 Fire Rings, Grills, Fireplaces, and Wood Stoves
This section requires fire building surfaces to be 9 inches minimum
above the ground, and cooking surfaces to be 15 inches minimum and 34
inches maximum above the ground. Where fire rings, grills, or
fireplaces are constructed with raised edges or walls, the depth of the
raised edge or wall is required to be 10 inches maximum. Fire rings
with double walls or insulation on the sides are recommended to prevent
burns.
1011.6 Water Spouts
This section requires water spouts at water hydrants and water
utility hook-ups to be 28 inches minimum and 36 inches maximum above
the ground.
1011.7 Outdoor Rinsing Showers
This section requires outdoor rinsing showers to provide at least
one hand-held shower spray unit with a hose 59 inches long minimum. The
hand-held shower spray unit is required to have at least one fixed
position located 15 inches minimum and 48 inches maximum above the
ground. Where vandalism is a consideration, a fixed shower head located
48 inches above the ground is permitted in place of a hand-held shower
spray unit.
1011.8 Viewing Scopes
This section requires eyepieces on viewing scopes to be 43 inches
minimum and 51 inches maximum above the ground.
1012 Parking Spaces Within Camping Units and Picnic Units and Pull-Up
Spaces at Dump Stations
1012.1 General
This section contains the technical requirements for parking spaces
provided within camping units and picnic units with mobility features
and pull-up spaces for recreational vehicles at dump stations. The
technical requirements address the width of parking spaces and pull-up
spaces for recreational vehicles (1012.2); the width of parking spaces
for vehicles, other than recreational vehicles (1012.3); and the
surface (1012.4) and slope (1012.5) of parking spaces and pull-up
spaces.
1012.2 Recreational Vehicles
This section requires parking spaces and pull-up spaces for
recreational vehicles to be 20 feet wide minimum to accommodate
recreational vehicles equipped with a lift. Recreational vehicles are
typically 8 feet wide. Recreational vehicles equipped with a lift need
an additional 8 feet of space on the passenger's side to deploy the
lift and for individuals who use wheeled mobility devices to maneuver
onto and off of the lift. Utility hook-ups for recreational vehicles
are typically located on the driver's side of the vehicle. An
additional 4 feet of space is needed on the driver's side for
individuals who use wheeled mobility devices to access the utility
hook-ups. Where two adjacent parking spaces are provided for
recreational vehicles, one of the parking spaces is permitted to be 16
feet wide minimum.
1012.3 Other Vehicles
This section requires parking spaces for vehicles, other than
recreational vehicles, to be 16 feet wide minimum to accommodate vans
equipped with a lift or ramp. Where two adjacent parking spaces are
provided for vehicles, other than recreational vehicles, one of the
parking spaces is permitted to be 8 feet wide minimum.
1012.4 Surface
This section requires the surface of parking spaces and pull-up
spaces to be firm and stable.
1012.5 Slope
This section requires the slope of the surface of parking spaces
and pull-up spaces to not be steeper than 1:48 in any direction. Where
the surface is other than asphalt, concrete, or boards, slopes not
steeper than 1:20 are permitted when necessary for drainage.
1013 Tent Pads & Tent Platforms
1013.1 General
This section contains the technical requirements for tent pads and
tent platforms provided within camping units with mobility features.
Tent pads and tent platforms are defined spaces with prepared surfaces
for setting up and securing tents. The technical requirements address
the clear ground space around tent pads and tent platforms (1013.2);
the slope of tent pads, tent platforms, and clear ground spaces
(1013.2); and the height of tent platforms (1013.4). When an entity
determines that a condition in 1019 does not permit full compliance
with a specific provision in 1013, the tent pad or tent platform is
permitted to comply with the provision to the extent practicable.
1013.2 Clear Ground Space
This section requires a clear ground space 4 feet wide minimum to
be provided on all usable sides of tent pads and tent platforms to
enable individuals who use wheeled mobility devices to set up and take
down the tent. The usable sides of tent pads and tent platforms are the
sides that can be used when setting up and taking down a tent. All
sides of tent pads and tent platforms are generally usable, unless a
tent pad or tent platform is located next to a natural feature such as
a rock or tree that renders a side not usable. This section also
requires the surface of the clear ground space to be firm and stable
and to allow the use of tent stakes or other tent securement devices.
1013.3 Slope
This section requires the slope of the surface of tent pads, tent
platforms, and clear ground spaces to not be steeper than 1:48 in any
direction. Where the surface is other than asphalt, concrete, or
boards, slopes not steeper than 1:20 are permitted when necessary for
drainage.
1013.4 Height
This section requires tent platforms to be 19 inches high maximum
measured from the clear ground space to the tent platform surface.
1014 Camp Shelters
1014.1 General
This section contains the technical requirements for camp shelters
with mobility features. The technical requirements address the entrance
to camp shelters (1014.2), including transfer access (1014.2.1) and
roll-in access (1014.2.2); and the floor within camp shelters (1014.3).
Two exceptions are provided. When an entity determines that a
condition in 1019 does not permit full compliance with a specific
provision in 1014, Exception 1 permits the camp shelter to comply with
the provision to the extent practicable. Exception 2 does not require
camp shelters to comply with the technical requirements for protruding
objects in 307 of the Architectural Barriers Act Accessibility
Guidelines.
1014.2 Entrance
This section requires camp shelters to provide either transfer
access or roll-in access at the entrance to the camp shelter.
1014.2.1 Transfer Access
Where transfer access is provided, this section requires a clear
ground

[[Page 59487]]

space 36 inches minimum by 48 inches minimum positioned for a parallel
approach to be provided at the entrance to the camp shelter, and one
full unobstructed side of the clear ground space to adjoin or overlap
an outdoor recreation access route or trail, as applicable, or another
clear ground space. The surface of the clear ground space is required
to be firm and stable, and to slope not steeper than 1:48 in any
direction. Where the surface is other than asphalt, concrete, or
boards, slopes not steeper than 1:20 are permitted when necessary for
drainage. The camp shelter floor at the entrance is required to be 19
inches high maximum measured from the clear ground space. These
requirements enable individuals who use wheeled mobility devices to
transfer from their mobility device to the shelter floor
1014.2.2 Roll-in Access
Where roll-in access is provided, this section requires a level or
sloped entry route complying with the technical requirements for
outdoor recreation access routes in 1016 or trails in 1017, as
applicable, at the entrance to the camp shelter. The section also
requires a turning space complying with 304.3 of the Architectural
Barriers Act Accessibility Guidelines to be provided within the camp
shelter. These requirements enable individuals who use wheeled mobility
devices to enter the shelter in their mobility device.
1014.3 Floor
This section requires the floor surface within camp shelters to be
firm and stable and to slope not steeper than 1:48 in any direction.
Where the floor surface is other than asphalt, concrete, or boards,
slopes not steeper than 1:20 are permitted when necessary for drainage.
1015 Viewing Areas
1015.1 General
This section contains the technical requirements for viewing areas.
The technical requirements address the clear ground space (1015.2) and
viewing space (1015.3) at distinct viewing locations; the turning space
within viewing areas (1015.4); and the surface (1015.5) and slope
(1015.6) of the clear ground space and turning space. In alterations,
when an entity determines that a condition in 1019 does not permit full
compliance with a specific provision in 1015, the viewing area is
permitted to comply with the provision to the extent practicable.
1015.2 Clear Ground Space
This section requires a clear ground space 36 inches minimum by 48
inches minimum positioned for either a forward or parallel approach to
be provided at each distinct viewing location, and one full
unobstructed side of the clear ground space to adjoin or overlap an
outdoor recreation access route or trail, as applicable, or another
clear ground space.
1015.3 Viewing Space
This section requires each distinct viewing location to provide a
viewing space adjacent to the clear ground space required by 1015.2
through which the point of interest is viewable. The viewing space is
required to be 32 inches maximum and 51 inches minimum high above the
ground and extend the full width of the clear ground space. Guards or
similar safety barriers are permitted to obstruct the viewing space to
the extent the obstruction is necessary for the guard or safety barrier
to serve its intended purpose.
1015.4 Turning Space
This section requires a turning space complying with 304.3 of the
Architectural Barriers Act Accessibility Guidelines to be provided
within the viewing area.
1015.5 Surface
This section requires the surface of the clear ground space and
turning space to be firm and stable.
1015.6 Slope
This section requires the slope of the surface of the clear ground
space and turning space to not be steeper than 1:48 in any direction.
Where the surface is other than asphalt, concrete, or boards, slopes
not steeper than 1:20 are permitted when necessary for drainage.
1016 Outdoor Recreation Access Routes
1016.1 General
This section contains the technical requirements for outdoor
recreation access routes. The technical requirements address the
surface of outdoor recreation access routes, passing spaces, and
resting intervals (1016.2); the clear width of outdoor recreation
access routes (1016.3); passing spaces (1016.4); obstacles (1016.5);
openings (1016.6); slopes, including running slope (1016.7.1) and cross
slope (1016.7.2); resting intervals (1016.8); and protruding objects
(1016.9).
Three exceptions are provided. Exception 1 applies to alterations
of existing camping facilities, picnic facilities, and trailheads.
Exception 2 applies to new construction and alterations of viewing
areas. When an entity determines that a condition in 1019 does not
permit full compliance with a specific provision in 1016 on a portion
of an outdoor recreation access route, Exceptions 1 and 2 permit the
portion of the outdoor recreation access route to comply with the
provision to the extent practicable. Exception 3 exempts outdoor
recreation access routes that are provided within vehicular ways from
complying with the technical requirements for passing spaces (1016.4);
running slope (1016.7.1) and cross slope (1016.7.2); and resting
intervals (1016.8).
1016.2 Surface
This section requires the surface of outdoor recreation access
routes, passing spaces, and resting intervals to be firm and stable.
1016.3 Clear Width
This section requires the clear width of outdoor recreation access
routes to be 36 inches minimum.
1016.4 Passing Spaces
This section requires passing spaces to be provided at intervals of
200 feet maximum where the clear width of outdoor recreation access
routes is less than 60 inches. Entities should consider providing
either 60 inches minimum clear width on outdoor recreation access
routes or passing spaces at shorter intervals where the route is
heavily used or adjoins elements, spaces, or facilities that are
heavily used; or where the route is a boardwalk or otherwise not at the
same level as the adjoining ground surface.
Passing spaces are required to be:
A space 60 inches minimum by 60 inches minimum; or
The intersection of two outdoor recreation access routes
providing a T-shaped space complying with 304.3.2 of the Architectural
Barriers Act Accessibility Guidelines where the base and the arms of
the T-shaped space extend 48 inches minimum beyond the intersection.
Where the intersection of two outdoor recreation access routes
serves as a passing space, the vertical alignment of the routes at the
intersection that form the T-shaped space is required to be nominally
planar (i.e., as flat as possible) so that all the wheels of a mobility
device touch the ground when turning into and out of the passing space.
Passing spaces and resting intervals are permitted to overlap.
Where passing spaces and resting intervals overlap, the technical
requirements for resting intervals in 1016.8.3 require the slope of the
surface to not be steeper than 1:48

[[Page 59488]]

in any direction. Where the surface is other than asphalt, concrete, or
boards, slopes not steeper than 1:20 are permitted when necessary for
drainage. Otherwise, passing space surfaces have the same slopes as the
adjoining outdoor recreation access route.
1016.5 Obstacles
This section contains technical requirements for obstacles on
outdoor recreation access routes, passing spaces, and resting
intervals. The vertical alignment of joints in concrete, asphalt, or
board surfaces on outdoor recreation access routes can be obstacles.
Natural features such as tree roots and rocks on outdoor recreation
access routes also can be obstacles. Where an outdoor recreation access
route is provided within a vehicular way, traffic calming devices can
be obstacles. This section requires obstacles to not exceed \1/2\ inch
in height measured vertically to the highest point. Where the surface
is other than concrete, asphalt, or boards, obstacles are permitted to
not exceed 1 inch in height measured vertically to the highest point.
The frequency of obstacles and obstacles that cross the full width
of outdoor recreation access routes can make travel difficult for
individuals who use wheeled mobility devices. Where possible, obstacles
that cross the full width of outdoor recreation access routes should be
separated by 48 inches minimum so individuals who use wheeled mobility
devices can cross the obstacle before confronting another obstacle.
1016.6 Openings
This section requires openings in the surface of outdoor recreation
access routes, passing spaces, and resting intervals such as spaces
between the boards in a boardwalk and drainage grates to not allow
passage of a sphere more than \1/2\ inch in diameter. Where possible,
drainage grates should be located outside the minimum clear width of
the recreation access route. Elongated openings should be placed so
that the long dimension is perpendicular, or as close to perpendicular
as possible, to the dominant direction of travel.
1016.7 Slopes
This section contains technical requirements for the maximum
running slope and segment length (1016.7.1) and cross slope (1016.7.2)
of outdoor recreation access routes.
1016.7.1 Maximum Running Slope and Segment Length
This section requires the running slope of any segment of an
outdoor recreation access route to not be steeper than 1:10 (10%).
Where the running slope of a segment of an outdoor recreation access
route is steeper than 1:20 (5%), the maximum length of the segment is
specified in Table 1016.7.1, and a resting interval is required at the
top and bottom of each segment. Gradual running slopes are more useable
by individuals with disabilities. Where the terrain results in steeper
running slopes, resting intervals are required more frequently. Where
running slopes are less severe, resting intervals are permitted to be
further apart.
1016.7.2 Cross Slope
This section requires the cross slope of outdoor recreation access
routes to not be steeper than 1:48. Where the surface is other than
asphalt, concrete, or boards, cross slopes not steeper than 1:20 are
permitted when necessary for drainage.
1016.8 Resting Intervals
This section contains the technical requirements for the length
(1016.8.1), width (1016.8.2), and slope (1016.8.3) of resting
intervals; and for a turning space (1016.8.4) where resting intervals
are provided adjacent to an outdoor recreation access route.
1016.8.1 Length
This section requires resting intervals to be 60 inches long
minimum.
1016.8.2 Width
This section requires resting intervals that are provided within an
outdoor recreation access route to be at least as wide as the widest
segment of the outdoor recreation access route leading to the resting
interval. Resting intervals that are provided adjacent to an outdoor
recreation access route are required to be 36 inches wide minimum.
1016.8.3 Slope
This section requires the slope of resting intervals to not be
steeper than 1:48 in any direction. Where the surface is other than
asphalt, concrete, or boards, slopes not steeper than 1:20 are
permitted when necessary for drainage.
1016.8.4 Turning Space
This section requires a turning space complying with 304.2.3 of the
Architectural Barriers Act Accessibility Guidelines where resting
intervals are provided adjacent to an outdoor recreation access route.
The vertical alignment of the outdoor recreation access route, turning
space, and resting interval is required to be nominally planar (i.e.,
as flat as possible) so that all the wheels of a mobility device touch
the ground when turning into and out of the resting interval.
1016.9 Protruding Objects
This section requires constructed elements on outdoor recreation
access routes, resting intervals, and passing spaces to comply with the
technical requirements for protruding objects in 307 of the
Architectural Barriers Act Accessibility Guidelines. Protruding objects
can be hazardous for individuals who are blind or have low vision.
Signs and other post mounted objects are examples of constructed
elements that can be protruding objects. Natural elements such as tree
branches are not required to comply with the technical requirements for
protruding objects in 307 of the Architectural Barriers Act
Accessibility Guidelines. However, entities should maintain the
vertical clearance along outdoor recreation access routes, resting
intervals, and passing spaces free from tree branches for 80 inches
high minimum above the ground.
1017 Trails
1017.1 General
This section contains the technical requirements for trails. The
technical requirements address the surface of the trails, passing
spaces, and resting intervals (1017.2); the clear tread width of trails
(1017.3); passing spaces (1017.4); tread obstacles (1017.5); openings
(1017.6); slopes, including running slope (1017.7.1) and cross slope
(1017.7.2); resting intervals (1017.8); protruding objects (1017.9);
and trailhead signs (1017.10).
Two exceptions are provided. When an entity determines that a
condition in 1019 does not permit full compliance with a specific
provision in 1017 on a portion of a trail, Exception 1 permits the
portion of trail to comply with the provision to the extent
practicable. When an entity determines that it is impracticable for the
entire trail to comply with the technical requirements in 1017,
Exception 2 exempts the entire trail from complying with the
requirements. This determination is made after the entity applies
Exception 1 to portions of the trail. The entity should consider the
portions of the trail that can and cannot fully comply with the
specific provisions in 1017 and the extent of compliance where full
compliance cannot be achieved when determining whether it would be

[[Page 59489]]

impracticable for the entire trail to comply with the technical
requirements in 1017. As discussed under F201.4.1, federal agencies are
required to document the basis for their determination when using
Exceptions 1 or 2, and are required notify us when using Exception 2.
1017.2 Surface
This section requires the surface of trails, passing spaces, and
resting intervals to be firm and stable. A firm trail surface resists
deformation by indentations. A stable trail surface is not permanently
affected by expected weather conditions and can sustain normal wear and
tear from the expected uses between planned maintenance.
1017.3 Clear Tread Width
This section requires the clear tread width of trails to be 36
inches minimum. The 36 inches minimum clear tread width is to be
maintained for the entire distance of the trail and may not be reduced
by gates, barriers, or other obstacles unless an entity determines
under Exception 1 to 1017.1 that a condition in 1019 does not permit
full compliance with the provision.
Where gates and barriers require wheelchair users to make 90 degree
or 180 degree turns, sufficient space should be provided for wheelchair
users to make the turns. We and National Institute on Disability and
Rehabilitation Research sponsored research to collect anthropometric
data from a sample of about 500 individuals who use manual wheelchairs,
power wheelchairs, and scooters. The research is known as the
Anthropometry of Wheeled Mobility Project and was conducted by the
Center for Inclusive Design and Environmental Access in the School of
Architecture and Planning, University at Buffalo, The State University
of New York. The reports on the Anthropometry of Wheeled Mobility
Project are available at: https://www.udeworld.com/anthropometrics.html.
The reports provide data on turning spaces for manual wheelchairs,
power wheelchairs, and scooters.
1017.4 Passing Spaces
This section requires passing spaces to be provided at intervals of
1000 feet maximum where the clear tread width of trails is less than 60
inches. Entities should consider providing either 60 inches minimum
clear tread width on trails or passing spaces at shorter intervals
where the trail is heavily used or where the trail is a boardwalk or
otherwise not at the same level as the adjoining ground surface. Where
the full length of a trail does not fully comply with the technical
requirements in 1017, a passing space is required to be located at the
end of the trail segment that fully complies with the technical
requirements 1017 to enable individuals who use wheeled mobility
devices to turn and exit the trail.
Passing spaces are required to be:
A space 60 inches minimum by 60 inches minimum; or
The intersection of two trails providing a T-shaped space
complying with 304.3.2 of the Architectural Barriers Act Accessibility
Guidelines where the base and the arms of the T-shaped space extend 48
inches minimum beyond the intersection.
Where the intersection of two trails serves as a passing space, the
vertical alignment of the trails at the intersection that form the T-
shaped space is required to be nominally planar (i.e., as flat as
possible) so that all the wheels of a mobility device touch the ground
when turning into and out of the passing space.
Passing spaces and resting intervals are permitted to overlap.
Where passing spaces and resting intervals overlap, the technical
requirements for resting intervals in 1017.8.3 require the slope of the
surface to not be steeper than 1:48 in any direction. Where the surface
is other than asphalt, concrete, or boards, slopes not steeper than
1:20 are permitted when necessary for drainage. Otherwise, passing
space surfaces have the same slopes as the adjoining trail tread.
1017.5 Tread Obstacles
This section contains technical requirements for tread obstacles on
trails, passing spaces, and resting intervals. The vertical alignment
of joints in concrete, asphalt, or board surfaces on trails can be
tread obstacles. Natural features such as tree roots and rocks within
the trail tread also can be obstacles. This section requires obstacles
to not exceed \1/2\ inch in height measured vertically to the highest
point. Where the surface is other than concrete, asphalt, or boards,
obstacles are permitted to not exceed 2 inches in height measured
vertically to the highest point.
The frequency of tread obstacles and tread obstacles that cross the
full width of the trail tread can make travel difficult for individuals
who use wheeled mobility devices. Where possible, tread obstacles that
cross the full width of the trail tread should be separated by 48
inches minimum so individuals who use wheeled mobility devices can
cross the obstacle before confronting another obstacle.
1017.6 Openings
This section requires openings in the surface of trails, passing
spaces, and resting intervals such as spaces between the boards in a
boardwalk to not allow passage of a sphere more than \1/2\ inch in
diameter. Elongated openings should be placed so that the long
dimension is perpendicular, or as close to perpendicular as possible,
to the dominant direction of travel.
1017.7 Slopes
This section contains technical requirements for the maximum
running slope and segment length (1017.7.1) and cross slope (1017.7.2)
of trails.
1017.7.1 Maximum Running Slope and Segment Length
This section requires that not more than 30 percent of the total
length of a trail have a running slope steeper than 1:12 (8.33%), and
that the running slope of any segment of a trail not be steeper than
1:8 (12%). Where the running slope of a segment a trail is steeper than
1:20 (5%), the maximum length of the segment is specified in Table
1017.7.1, and a resting interval is required at the top and bottom of
each segment. Gradual running slopes are more useable by individuals
with disabilities. Where the terrain results in steeper running slopes,
resting intervals are required more frequently. Where running slopes
are less severe, resting intervals are permitted to be further apart.
1017.7.2 Cross Slope
This section requires the cross slope of trails to not be steeper
than 1:48. Where the surface is other than asphalt, concrete, or
boards, cross slopes not steeper than 1:20 are permitted when necessary
for drainage.
1017.8 Resting Intervals
This section contains the technical requirements for the length
(1017.8.1), width (1017.8.2), and slope (1017.8.3) of resting
intervals; and for a turning space (1017.8.4) where resting intervals
are provided adjacent to a trail.
1017.8.1 Length
This section requires resting intervals to be 60 inches long
minimum.
1017.8.2 Width
This section requires resting intervals that are provided within
the trail tread to be at least as wide as the widest segment of the
trail tread leading to the resting interval. Resting intervals that are
provided adjacent to the trail tread are required to be 36 inches wide
minimum.

[[Page 59490]]

1017.8.3 Slope
This section requires the slope of resting intervals to not be
steeper than 1:48 in any direction. Where the surface is other than
asphalt, concrete, or boards, slopes not steeper than 1:20 are
permitted when necessary for drainage.
1017.8.4 Turning Space
This section requires a turning space complying with 304.2.3 of the
Architectural Barriers Act Accessibility Guidelines where resting
intervals are provided adjacent to the trail tread. The vertical
alignment of the trail tread, turning space, and resting interval is
required to be nominally planar (i.e., as flat as possible) so that all
the wheels of a mobility device touch the ground when turning in and
out of the resting interval.
1017.9 Protruding Objects
This section requires constructed elements on trails, resting
intervals, and passing spaces to comply with the technical requirements
for protruding objects in 307 of the Architectural Barriers Act
Accessibility Guidelines. Protruding objects can be hazardous for
individuals who are blind or have low vision. Signs and other post
mounted objects are examples of constructed elements that can be
protruding objects. Natural elements such as tree branches are not
required to comply with the technical requirements for protruding
objects in 307 of the Architectural Barriers Act Accessibility
Guidelines. However, entities should maintain the vertical clearance
along the trail tread, resting intervals, and passing spaces free from
tree branches for 80 inches high minimum above the ground.
1017.10 Trailhead Signs
This section requires trail information signs at trailheads to
include information on the length of the trail or trail segment;
surface type; typical and minimum tread width; typical and maximum
running slope; and typical and maximum cross slope. This information
enables individuals with disabilities to decide whether to hike the
trail based on the characteristics of the trail. Entities also should
provide information about the accessibility of trails on Web sites.
1018 Beach Access Routes
1018.1 General
This section contains the technical requirements for beach access
routes. The technical requirements address connections (1018.2);
surface (1018.3); clear width (1018.4); obstacles (1018.5); openings
(1018.6); slopes, including running slope (1018.7.1) and cross slope
(1018.7.2); resting intervals (1018.8); protruding objects (1018.9);
and dune crossings (1018.10).
Three exceptions are provided. When an entity determines that a
condition in 1019 does not permit full compliance with a specific
provision in 1018 on a portion of a beach access route, Exception 1
permits the portion of route to comply with the provision to the extent
practicable. When an entity determines that it is impracticable to
provide a beach access route complying with the technical requirements
in 1018, Exception 2 does not require a beach access route. This
determination is made after the entity applies Exception 1 to portions
of the route. The entity should consider the portions of the beach
access route that can and cannot fully comply with the specific
provisions in 1018 and the extent of compliance where full compliance
cannot be achieved when determining whether it would be impracticable
to provide a beach access route complying with the technical
requirements in 1018. Exception 3 exempts removable beach access routes
from complying with the technical requirements for running slope
(1018.7.1) and cross slope (1018.7.2); resting intervals (1018.8); and
dune crossings (1018.10). As discussed under F201.4.1, federal agencies
are required to document the basis for their determination when using
Exceptions 1 or 2, and are required to notify us when using Exception
2.
1018.2 Connections
This section requires beach access routes to connect an entry point
to the beach to the high tide level at tidal beaches; mean high water
level at river beaches; and normal recreation water level at lake,
pond, and reservoir beaches.
1018.3 Surface
This section requires the surface of beach access routes and
resting intervals to be firm and stable.
1018.4 Clear Width
This section requires the clear width of beach access routes to be
60 inches minimum to enable individuals who use wheeled mobility
devices to pass beach visitors traveling in the opposite direction. An
exception permits the clear width of beach access routes that are not
removable to be reduced to 48 inches minimum at dune crossings.
Where gates or barriers are installed to control access to beaches,
the gates or barriers should permit the passage of beach wheelchairs.
Beach wheelchairs have large, wide wheels that can roll across sand
without sinking. Gates or barriers that have clear openings at least 48
inches wide will accommodate most beach wheelchairs.
1018.5 Obstacles
This section contains technical requirements for obstacles on beach
access routes and resting intervals. The vertical alignment of boards
on a beach access route or removable sections of a beach access route
can be obstacles. This section requires obstacles to not exceed \1/2\
inch in height measured vertically to the highest point. Where the
surface is other than concrete, asphalt, or boards, obstacles are
permitted to not exceed 1 inch in height measured vertically to the
highest point.
1018.6 Openings
This section requires openings in the surface of beach access
routes and resting intervals such as spaces between boards to not allow
passage of a sphere more than \1/2\ inch in diameter. Elongated
openings should be placed so that the long dimension is perpendicular,
or as close to perpendicular as possible, to the dominant direction of
travel.
1018.7 Slopes
This section contains technical requirements for the maximum
running slope and segment length (1018.7.1) and cross slope (1018.7.2)
of beach access routes.
1018.7.1 Maximum Running Slope and Segment Length
This section requires that the running slope of any segment of a
beach access route not be steeper than 1:10 (10%). Where the running
slope of a segment a beach access route is steeper than 1:20 (5%), the
maximum length of the segment is specified in Table 1018.7.1, and a
resting interval is required at the top and bottom of each segment.
Gradual running slopes are more useable by individuals with
disabilities. Where the terrain results in steeper running slopes,
resting intervals are required more frequently. Where running slopes
are less severe, resting intervals are permitted to be further apart.
1018.7.2 Cross Slope
This section requires the cross slope of beach access routes to not
be steeper than 1:48. Where the surface is other than asphalt,
concrete, or boards, cross slopes not steeper than 1:20 are permitted
when necessary for drainage.

[[Page 59491]]

1018.8 Resting Intervals
This section contains the technical requirements for the size
(1018.8.1) and slope (1017.8.2) of resting intervals.
1018.8.1 Size
This section requires resting intervals to be 60 inches minimum by
60 inches minimum.
1018.8.2 Slope
This section requires the slope of resting intervals to not be
steeper than 1:48 in any direction. Where the surface is other than
asphalt, concrete, or boards, slopes not steeper than 1:20 are
permitted when necessary for drainage.
1018.9 Protruding Objects
This section requires constructed elements on beach access routes
and resting intervals to comply with the technical requirements for
protruding objects in 307 of the Architectural Barriers Act
Accessibility Guidelines. Protruding objects can be hazardous for
individuals who are blind or have low vision. Signs and other post
mounted objects are examples of constructed elements that can be
protruding objects.
1018.10 Dune Crossings
This section requires handrails complying with 505 of the
Architectural Barriers Act Accessibility Guidelines and curbs or
barriers to be provided where the slope of a beach access route at a
dune crossing is steeper than 1:20 (5%). The curbs or barriers are
required to prevent the passage of a 2 inch diameter sphere, where any
portion of the sphere is within 2 inches of the crossing surface.
1019 Conditions for Exceptions
1019.1 General
This section lists the conditions for the exceptions to specific
provisions in 1011, 1013, 1014, 1015, 1016, 1017, and 1018. When an
entity determines that any of the following conditions does not permit
full compliance with the provision, compliance is required to the
extent practicable:
Compliance is not practicable due to terrain.
Compliance cannot be accomplished with the prevailing
construction practices.
Compliance would fundamentally alter the function or
purpose of the facility or the setting.
Compliance is limited or precluded by any of the following
laws, or by decisions or opinions issued or agreements executed
pursuant to any of the following laws: Endangered Species Act; National
Environmental Policy Act; National Historic Preservation Act;
Wilderness Act; or other federal, state, or local law the purpose of
which is to preserve threatened or endangered species; the environment;
or archaeological, cultural, historical, or other significant natural
features.
The last condition allows the following to be a basis for using the
exceptions:
Opinions issued by the Secretary of the Interior pursuant
to the Endangered Species Act stating how a federal agency can
implement an action without jeopardizing the continued existence of any
endangered species or threatened species, or destroying or adversely
modifying the habitat of such species (16 U.S.C. 1536 (b) (3) (A));
Decisions issued by a federal agency pursuant to the
National Environmental Policy Act in actions requiring environmental
impact statements stating how it will avoid or minimize environmental
harm (42 U.S.C. 4332; 40 CFR 1505.2);
Agreements executed or decisions issued by a federal
agency pursuant to National Historic Preservation Act stating how it
will avoid, minimize, or mitigate adverse effects on historical
properties (16 U.S.C. 470f and 470h-2; 36 CFR 800.6 (b) (iv) and 800.7
(c) (4)); and
Provisions in the Wilderness Act that require federal
agencies to preserve the wilderness character of designated wilderness
areas and prohibit any structure or installation within such areas (16
U.S.C. 1131 (b) and (c)).

7. Regulatory Analyses

Executive Order 13563 (Improving Regulation and Regulatory Review) and
Executive Order 12866 (Regulatory Planning and Review)

This final rule is not a significant regulatory action. We adhered
to the principles of regulation in Executive Orders 13563 and 12866.
Among other things, Executive Order 13563 directs agencies to propose
or adopt a regulation only upon a reasoned determination that its
benefits justify its costs; tailor the regulation to impose the least
burden on society, consistent with obtaining the regulatory objectives;
and, in choosing among alternative regulatory approaches, select those
approaches that maximize net benefits. Executive Order 13563 recognizes
that some benefits are difficult to quantify and provides that, where
appropriate and permitted by law, agencies may consider and discuss
qualitatively values that are difficult or impossible to quantify,
including equity, human dignity, fairness, and distributive impacts.
We prepared a regulatory assessment for the final rule. The
regulatory assessment is available at: https://www.access-board.gov/outdoor (click on Background). The costs and benefits of the final rule
are discussed below.
Costs
The regulatory assessment compares the final rule to the guidelines
and standards used by federal agencies for the design of outdoor
developed areas without regard to accessibility to determine whether
the final rule would result in additional costs. The regulatory
assessment shows that the final rule would not result in additional
costs for camping facilities and picnic facilities. The regulatory
assessment shows that the final rule would result in additional costs
for viewing areas, trails, and beach access routes as shown in Table 4.

Table 4--Additional Costs Due to Final Rule
----------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------
Viewing Areas............................... $2,176 for dual base binocular scopes and $3,380 for a dual base
telescopes, if viewing scopes provided at viewing areas.
Trails...................................... $40,655 per trail mile, if trail would not otherwise meet the
technical requirements and the exceptions to the technical
requirements do not apply to the trail.
Beach Access Routes......................... $4,497 to $6,530 to purchase roll-out mats for beach access
routes, if parking areas, toilet facilities, bathing facilities,
and circulation paths serving beaches are constructed or altered
or beach nourishment project is undertaken.
----------------------------------------------------------------------------------------------------------------

We estimate the federal agencies would incur $1.2 million
additional annual costs due to the final rule for viewing areas,
trails, and beach access routes as shown in Table 5.

[[Page 59492]]

Table 5--Additional Annual Costs for Federal Agencies
----------------------------------------------------------------------------------------------------------------
Facility Total annual costs Assumptions
----------------------------------------------------------------------------------------------------------------
Viewing Areas................. $241,971 Fish and Wildlife
Service provides a
viewing scope over
five years at 556
wildlife refuges to
enhance visitor
experiences.
Trails........................ 617,956 Federal agencies
construct 15.2 trail
miles per year
covered by the
scoping requirements
in F247 that would
not otherwise meet
the technical
requirements for
trails in 1017 and
the exceptions in
1017 do not apply to
the trails.
Beach Access Routes........... \1\ 344,662 Federal agencies
provide beach access
routes at 1,025
beaches over 20 years
as parking areas,
restrooms, shower
facilities, and
circulation paths
serving the beaches
are altered or
replaced with new
facilities.
----------------------------------------------------------------------------------------------------------------
1. Estimate is based on higher cost for roll-out mats.

Benefits
The final rule would increase opportunities for individuals with
mobility disabilities to participate in outdoor recreation activities
with their families and friends. Participation in outdoor recreation
activities provides the following benefits:
Physical health benefits, including reduces obesity,
diminishes risk of chronic disease; and increases life expectancy;
Mental health benefits, including reduces depression,
relieves stress, and improves quality of life; and
Community and social benefits, including unites families
and promotes stewardship.\9\
---------------------------------------------------------------------------

\9\ These benefits are documented in California State Parks, The
Health and Social Benefits of Recreation, 2005 at: https://www.parks.ca.gov/pages/795/files/health_benefits_online_6-1-05.pdf and Geoffrey Godbey, Outdoor Recreation, Health, and
Wellness: Understanding and Enhancing the Relationship, 2009 at:
https://www.rff.org/rff/documents/rff-dp-09-21.pdf.
---------------------------------------------------------------------------

The benefits are difficult to quantify, but include important
national values recognized in Executive Order 13563 such as equity,
human dignity, and fairness.
The 2010 Survey of Income and Program Participation (SIPP)
sponsored by the U.S. Census Bureau estimates that among the civilian
non-institutionalized population aged 15 and older, 30.6 million
persons (12.6%) had limitations associated with ambulatory activities
of the lower body.\10\ This number includes 23.9 million persons (9.9%)
who had difficulty walking a quarter of a mile; 22.3 million (9.2%) who
have difficulty climbing a flight of stairs; 11.6 million persons
(4.8%) who used a cane, crutches, or walker to assist with mobility;
and 3.6 million persons (1.5%) who use a wheelchair or scooter. Not all
these persons are likely to directly benefit from the final rule
because some may not participate in outdoor recreational activities. We
do not have information to estimate the number of individuals with
mobility disabilities who would directly benefit from the final rule.
---------------------------------------------------------------------------

\10\ Americans with Disabilities: 2010 available at: https://www.census.gov/prod/2012pubs/p70-131.pdf.
---------------------------------------------------------------------------

Final Regulatory Flexibility Analysis

The Regulatory Flexibility Act requires federal agencies to
consider the impacts of their rules on small entities, analyze
alternatives that minimize the impacts on small entities, and to make
the analysis available to the public. See 5 U.S.C. 604. We certified
that the proposed rule would not have a significant economic impact on
a substantial number of small entities because it would apply to
federal agencies that administer outdoor areas developed for
recreational purposes. Therefore, we did not prepare an initial
regulatory flexibility analysis for the proposed rule. However, the
Architectural Barriers Act also applies to facilities constructed or
altered by non-federal entities on behalf of the United States. We
prepared a final regulatory flexibility analysis for the final rule to
consider the impacts of the final rule on small entities that construct
or alter recreation facilities on federal lands on behalf of federal
agencies pursuant to a concession contract, partnership agreement, or
similar arrangement.

Need for and Objective of Final Rule

The Architectural Barriers Act requires facilities constructed or
altered by or on behalf of federal agencies to be readily accessible to
and usable by individuals with disabilities. Certain agencies are
required to adopt accessibility standards for the design, construction,
and alteration of facilities covered by the Architectural Barriers Act.
We are required by section 502 of the Rehabilitation Act to establish
and maintain minimum guidelines and requirements for the accessibility
standards adopted the federal agencies. We are issuing the final rule
pursuant to this authority to establish accessibility guidelines for
camping facilities, picnic facilities, viewing areas, trails, and beach
access routes constructed or altered by or behalf of federal agencies
that administer outdoor developed areas.

Significant Issues Raised by Public Comments in Response to the Initial
Regulatory Flexibility Analysis

As noted above, we certified that the proposed rule would not have
a significant economic impact on a substantial number of small
entities. Therefore, we did not prepare an initial regulatory
flexibility analysis for the proposed rule.

Response to Comments Filed by Chief Counsel for Advocacy of the Small
Business Administration

The Chief Counsel for Advocacy of the Small Business Administration
did not file comments on the proposed rule.

Small Entities Affected by Rule

The final rule affects small entities that construct or alter
camping facilities, picnic facilities, viewing areas, trails, and beach
facilities on federal lands pursuant to a concession contract,
partnership agreement, or similar arrangement with the following
federal agencies and their components: U.S. Department of Agriculture
(Forest Service), U.S. Department of Defense (Army Corps of Engineers),
and U.S. Department of the Interior (Bureau of Land Management, Bureau
of Reclamation, Fish and Wildlife Service, National Park Service). Data
are not available on the number of small entities that construct or
alter camping facilities, picnic facilities, viewing

[[Page 59493]]

areas, trails, and beach facilities on federal lands pursuant to a
concession contract, partnership agreement, or similar arrangement with
the federal agencies. Small entities that construct facilities of
federal land pursuant to a concession contract with federal agencies
can include the costs of the capital improvements, including additional
costs due to the final rule, in the contract bids and the costs can be
offset in the concession fees paid to the federal agencies.

Compliance Requirements in Final Rule

The final rule contains scoping and technical requirements for
camping facilities, picnic facilities, viewing areas, trails, and beach
access routes. Scoping requirements specify what features are required
to be accessible and, where multiple features of the same type are
provided, how many of the features are required to be accessible. The
scoping requirements in the final rule are summarized in Table 1 under
Executive Summary. Technical requirements specify the design criteria
for accessible features. The technical requirements include design
criteria for the following outdoor constructed features: picnic tables,
fire rings, grills, fireplaces, wood stoves, trash and recycling
receptacles, water hydrants, utility and sewage hookups, outdoor
rinsing showers, benches, and viewing scopes. The technical
requirements also include design criteria for parking spaces within
camping units and picnic units with mobility features; pull-up spaces
for recreational vehicles at dump stations; tent pads and tent
platforms; camp shelters; viewing areas; outdoor recreation access
routes; trails; and beach access routes.

Steps To Minimize Significant Economic Impacts on Small Entities

The final rules permits exceptions to the specific provisions in
the technical requirements for certain elements and facilities based on
the conditions listed in Table 2 under Executive Summary. When an
entity determines that a condition does not permit full compliance with
a provision, compliance is required to the extent practicable. The
final rule allows exemptions for an entire trail or beach access route
when an entity determines that is impracticable for a trail to comply
with the technical requirements for trails or to provide a beach access
route complying with the technical requirements for beach access
routes. This determination is made after the entity applies the
exceptions for specific provisions in the technical requirements for
trails or beach access routes to portions of the trail or route.

Executive Order 13132 (Federalism)

The final rule does not have federalism implications as defined in
Executive Order 13112. The final rule does not have substantial direct
effects on the states or on the relationship, or the distribution of
power and responsibilities, between the federal government and the
states.

Unfunded Mandates Reform Act

The final rule does not impose a federal intergovernmental mandate
or federal private sector mandate as those terms are defined in the
Unfunded Mandates Reform Act. Any duties imposed on state, local, or
tribal governments or on the private sector arise from participation in
a voluntary federal program.

List of Subjects in 36 CFR Part 1191

Buildings and facilities, Civil rights, Incorporation by reference,
Individuals with disabilities, Transportation.

Karen L. Braitmayer,
Chair.

For the reasons stated in the preamble, we amend 36 CFR part 1191
as follows:

PART 1191--AMERICANS WITH DISABILITIES ACT (ADA) ACCESSIBILITY
GUIDELINES FOR BUILDINGS AND FACILITIES; ARCHITECTURAL BARRIERS ACT
(ABA) ACCESSIBILITY GUIDELINES

0
1. The authority citation for 36 CFR part 1191 continues to read as
follows:

Authority: 29 U.S.C. 792 (b)(3); 42 U.S.C. 12204.

0
2-3. In Sec. 1191.1, redesignate Note 1 to paragraph (a) as Note 3 and
add new Notes 1 and 2 to paragraph (a) and redesignate Notes 1 and 2 to
paragraph (b) as Notes 2 and 3 and add new Notes 1 and 4 to paragraph
(b) to read as follows:

Sec. 1191.1 Accessibility guidelines.

(a) * * *

Note 1 to paragraph (a): 1. Advisory sections and figures that
illustrate the technical requirements in Appendix D are available on
the Internet at: www.access-board.gov. The advisory sections provide
guidance only and do not contain mandatory requirements.

Note 2 to paragraph (a): 2. The Department of Justice adopted
the 2010 ADA Standards for Accessible Design (2010 Standards) as the
regulatory standards for the new construction and alteration of
facilities subject to its regulations under the Americans with
Disabilities Act (ADA), effective March 15, 2012. 28 CFR
35.151(c)(3), as amended at 75 FR 56163, September 15, 2010; and 28
CFR 36.406(a)(3), as amended at 75 FR 56236, September 15, 2010. For
state and local governments, the 2010 Standards consist of the
regulations at 28 CFR 35.151 and the versions of Appendices B and D
to this part published in the 2009 edition of the Code of Federal
Regulations. 28 CFR 35.104. For public accommodations and commercial
facilities, the 2010 Standards consist of the regulations at 28 CFR
part 36, subpart D and the versions of Appendices B and D to this
part published in the 2009 edition of the Code of Federal
Regulations. 28 CFR 36.104. Because Appendices B and D to this part,
as published in the 2009 edition of the Code of Federal Regulations,
were adopted by reference by the Department of Justice as part of
the 2010 Standards for new construction and alteration of facilities
subject to its ADA regulations, subsequent revisions to Appendices B
and D by the Access Board are not included in the 2010 Standards and
have no legal effect for facilities subject to its ADA regulations
until adopted by the Department of Justice. Therefore, the public is
cautioned not to use Appendices B and D to this part published in
any edition of the Code of Federal Regulations after 2013, until
such time as the later edition is adopted by the Department of
Justice as a regulatory standard. Complete copies of the 2010
Standards can be obtained from the Department of Justice's ADA Web
site at: https://www.ada.gov/2010ADAstandards_index.htm, or by
contacting the DOJ Information Line, at: 800-514-0301 (Voice) or
800-514-0383 (TTY).

* * * * *
(b) * * *

Note 1 to paragraph (b): 1. Advisory sections and figures that
illustrate the technical requirements in Appendix D are available on
the Internet at: www.access-board.gov. The advisory sections provide
guidance only and do not contain mandatory requirements.

* * * * *

Note 4 to paragraph (b): 4. The Department of Defense adopted by
reference Appendices B and D to this part as accessibility standards
for the new construction and alteration of its facilities subject to
the Architectural Barriers Act, effective October 31, 2008. Deputy
Secretary of Defense Memorandum dated October 31, 2008, Access for
People with Disabilities [available on the Internet at: https://www.access-board.gov/guidelines-and-standards/buildings-and-sites/about-the-aba-standards/background/dod-memorandum].

0
4. Revise appendix A to part 1191 to read as follows:

Appendix A to Part 1191--Table Of Contents

ADA CHAPTER 1: APPLICATION AND ADMINISTRATION

101 Purpose
102 Dimensions for Adults and Children
103 Equivalent Facilitation

[[Page 59494]]

104 Conventions
105 Referenced Standards
106 Definitions

ADA CHAPTER 2: SCOPING REQUIREMENTS

201 Application
202 Existing Buildings and Facilities
203 General Exceptions
204 Protruding Objects
205 Operable Parts
206 Accessible Routes
207 Accessible Means of Egress
208 Parking Spaces
209 Passenger Loading Zones and Bus Stops
210 Stairways
211 Drinking Fountains
212 Kitchens, Kitchenettes, and Sinks
213 Toilet Facilities and Bathing Facilities
214 Washing Machines and Clothes Dryers
215 Fire Alarm Systems
216 Signs
217 Telephones
218 Transportation Facilities
219 Assistive Listening Systems
220 Automatic Teller Machines and Fare Machines
221 Assembly Areas
222 Dressing, Fitting, and Locker Rooms
223 Medical Care and Long-Term Care Facilities
224 Transient Lodging Guest Rooms
225 Storage
226 Dining Surfaces and Work Surfaces
227 Sales and Service
228 Depositories, Vending Machines, Change Machines, Mail Boxes, and
Fuel Dispensers
229 Windows
230 Two-Way Communication Systems
231 Judicial Facilities
232 Detention Facilities and Correctional Facilities
233 Residential Facilities
234 Amusement Rides
235 Recreational Boating Facilities
236 Exercise Machines and Equipment
237 Fishing Piers and Platforms
238 Golf Facilities
239 Miniature Golf Facilities
240 Play Areas
241 Saunas and Steam Rooms
242 Swimming Pools, Wading Pools, and Spas
243 Shooting Facilities with Firing Positions

ABA CHAPTER 1: APPLICATION AND ADMINISTRATION

F101 Purpose
F102 Dimensions for Adults and Children
F103 Modifications and Waivers
F104 Conventions
F105 Referenced Standards
F106 Definitions

ABA CHAPTER 2: SCOPING REQUIREMENTS

F201 Application
F202 Existing Buildings and Facilities
F203 General Exceptions
F204 Protruding Objects
F205 Operable Parts
F206 Accessible Routes
F207 Accessible Means of Egress
F208 Parking Spaces
F209 Passenger Loading Zones and Bus Stops
F210 Stairways
F211 Drinking Fountains
F212 Kitchens, Kitchenettes, and Sinks
F213 Toilet Facilities and Bathing Facilities
F214 Washing Machines and Clothes Dryers
F215 Fire Alarm Systems
F216 Signs
F217 Telephones
F218 Transportation Facilities
F219 Assistive Listening Systems
F220 Automatic Teller Machines and Fare Machines
F221 Assembly Areas
F222 Dressing, Fitting, and Locker Rooms
F223 Medical Care and Long-Term Care Facilities
F224 Transient Lodging Guest Rooms
F225 Storage
F226 Dining Surfaces and Work Surfaces
F227 Sales and Service
F228 Depositories, Vending Machines, Change Machines, Mail Boxes,
and Fuel Dispensers
F229 Windows
F230 Two-Way Communication Systems
F231 Judicial Facilities
F232 Detention Facilities and Correctional Facilities
F233 Residential Facilities
F234 Amusement Rides
F235 Recreational Boating Facilities
F236 Exercise Machines and Equipment
F237 Fishing Piers and Platforms
F238 Golf Facilities
F239 Miniature Golf Facilities
F240 Play Areas
F241 Saunas and Steam Rooms
F242 Swimming Pools, Wading Pools, and Spas
F243 Shooting Facilities with Firing Positions
F244 Camping Facilities
F245 Picnic Facilities
F246 Viewing Areas
F247 Trails
F248 Beach Access Routes

CHAPTER 3: BUILDING BLOCKS

301 General
302 Floor or Ground Surfaces
303 Changes in Level
304 Turning Space
305 Clear Floor or Ground Space
306 Knee and Toe Clearance
307 Protruding Objects
308 Reach Ranges
309 Operable Parts

CHAPTER 4: ACCESSIBLE ROUTES

401 General
402 Accessible Routes
403 Walking Surfaces
404 Doors, Doorways, and Gates
405 Ramps
406 Curb Ramps
407 Elevators
408 Limited-Use/Limited-Application Elevators
409 Private Residence Elevators
410 Platform Lifts

CHAPTER 5: GENERAL SITE AND BUILDING ELEMENTS

501 General
502 Parking Spaces
503 Passenger Loading Zones
504 Stairways
505 Handrails

CHAPTER 6: PLUMBING ELEMENTS AND FACILITIES

601 General
602 Drinking Fountains
603 Toilet and Bathing Rooms
604 Water Closets and Toilet Compartments
605 Urinals
606 Lavatories and Sinks
607 Bathtubs
608 Shower Compartments
609 Grab Bars
610 Seats
611 Washing Machines and Clothes Dryers
612 Saunas and Steam Rooms

CHAPTER 7: COMMUNICATION ELEMENTS AND FEATURES

701 General
702 Fire Alarm Systems
703 Signs
704 Telephones
705 Detectable Warnings
706 Assistive Listening Systems
707 Automatic Teller Machines and Fare Machines
708 Two-Way Communication Systems

CHAPTER 8: SPECIAL ROOMS, SPACES, AND ELEMENTS

801 General
802 Wheelchair Spaces, Companion Seats, and Designated Aisle Seats
803 Dressing, Fitting, and Locker Rooms
804 Kitchens and Kitchenettes
805 Medical Care and Long-Term Care Facilities
806 Transient Lodging Guest Rooms
807 Holding Cells and Housing Cells
808 Courtrooms
809 Residential Dwelling Units
810 Transportation Facilities
811 Storage

CHAPTER 9: BUILT-IN ELEMENTS

901 General
902 Dining Surfaces and Work Surfaces
903 Benches
904 Check-Out Aisles and Sales and Service Counters

CHAPTER 10: RECREATION FACILITIES

1001 General
1002 Amusement Rides
1003 Recreational Boating Facilities
1004 Exercise Machines and Equipment
1005 Fishing Piers and Platforms
1006 Golf Facilities
1007 Miniature Golf Facilities
1008 Play Areas
1009 Swimming Pools, Wading Pools, and Spas
1010 Shooting Facilities with Firing Positions
1011 Outdoor Constructed Features
1012 Parking Spaces Within Camping Units and Picnic Units and Pull-
Up Spaces at Dump Stations
1013 Tent Pads and Tent Platforms
1014 Camp Shelters
1015 Viewing Areas
1016 Outdoor Recreation Access Routes
1017 Trails
1018 Beach Access Routes

[[Page 59495]]

1019 Conditions for Exceptions

0
5. Revise appendix B to part 1191 to read as follows:

Appendix B to Part 1191--Americans With Disabilities Act: Scoping

ADA CHAPTER 1: APPLICATION AND ADMINISTRATION

101 Purpose

101.1 General. This document contains scoping and technical
requirements for accessibility to sites, facilities, buildings, and
elements by individuals with disabilities. The requirements are to
be applied during the design, construction, additions to, and
alteration of sites, facilities, buildings, and elements to the
extent required by regulations issued by Federal agencies under the
Americans with Disabilities Act of 1990 (ADA).
101.2 Effect on Removal of Barriers in Existing Facilities. This
document does not address existing facilities unless altered at the
discretion of a covered entity. The Department of Justice has
authority over existing facilities that are subject to the
requirement for removal of barriers under title III of the ADA. Any
determination that this document applies to existing facilities
subject to the barrier removal requirement is solely within the
discretion of the Department of Justice and is effective only to the
extent required by regulations issued by the Department of Justice.

102 Dimensions for Adults and Children

102.1 General. The technical requirements are based on adult
dimensions and anthropometrics. In addition, this document includes
technical requirements based on children's dimensions and
anthropometrics for drinking fountains, water closets, toilet
compartments, lavatories and sinks, dining surfaces, and work
surfaces.

103 Equivalent Facilitation

103.1 General. Nothing in these requirements prevents the use of
designs, products, or technologies as alternatives to those
prescribed, provided they result in substantially equivalent or
greater accessibility and usability.

104 Conventions

104.1 Dimensions. Dimensions that are not stated as ``maximum''
or ``minimum'' are absolute.
104.1.1 Construction and Manufacturing Tolerances. All
dimensions are subject to conventional industry tolerances except
where the requirement is stated as a range with specific minimum and
maximum end points.
104.2 Calculation of Percentages. Where the required number of
elements or facilities to be provided is determined by calculations
of ratios or percentages and remainders or fractions result, the
next greater whole number of such elements or facilities shall be
provided. Where the determination of the required size or dimension
of an element or facility involves ratios or percentages, rounding
down for values less than one half shall be permitted.

105 Referenced Standards

105.1 General. The standards listed in 105.2 are incorporated by
reference in this document and are part of the requirements to the
prescribed extent of each such reference. The Director of the
Federal Register has approved these standards for incorporation by
reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51.
Copies of the referenced standards may be inspected at the
Architectural and Transportation Barriers Compliance Board, 1331 F
Street NW., Suite 1000, Washington, DC 20004; at the Department of
Justice, Civil Rights Division, Disability Rights Section, 1425 New
York Avenue NW., Washington, DC 20005; at the Department of
Transportation, 1200 New Jersey Avenue SE., Washington, DC 20590; or
at the National Archives and Records Administration (NARA). For
information on the availability of this material at NARA, call (202)
741-6030, or go to https://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
105.2 Referenced Standards. The specific edition of the
standards listed below are referenced in this document. Where
differences occur between this document and the referenced
standards, this document applies.
105.2.1 ANSI/BHMA. Copies of the referenced standards may be
obtained from the Builders Hardware Manufacturers Association, 355
Lexington Avenue, 15th floor, New York, NY 10017 (https://www.buildershardware.com).
ANSI/BHMA A156.10-1999 American National Standard for Power
Operated Pedestrian Doors (see 404.3).
ANSI/BHMA A156.19-1997 American National Standard for Power
Assist and Low Energy Power Operated Doors (see 404.3, 408.3.2.1,
and 409.3.1).
ANSI/BHMA A156.19-2002 American National Standard for Power
Assist and Low Energy Power Operated Doors (see 404.3, 408.3.2.1,
and 409.3.1).
105.2.2 ASME. Copies of the referenced standards may be obtained
from the American Society of Mechanical Engineers, Two Park Avenue,
New York, New York 10016 (https://www.asme.org).
ASME A17.1-2000 Safety Code for Elevators and Escalators,
including ASME A17.1a-2002 Addenda and ASME A17.1b-2003 Addenda (see
407.1, 408.1, 409.1, and 810.9).
ASME A18.1-1999 Safety Standard for Platform Lifts and Stairway
Chairlifts, including ASME A18.1a-2001 Addenda and ASME A18.1b]2001
Addenda (see 410.1).
ASME A18.1-2003 Safety Standard for Platform Lifts and Stairway
Chairlifts, (see 410.1).
105.2.3 ASTM. Copies of the referenced standards may be obtained
from the American Society for Testing and Materials, 100 Bar Harbor
Drive, West Conshohocken, Pennsylvania 19428 (https://www.astm.org).
ASTM F1292-99 Standard Specification for Impact Attenuation of
Surface Systems Under and Around Playground Equipment (see
1008.2.6.2).
ASTM F1292-04 Standard Specification for Impact Attenuation of
Surfacing Materials Within the Use Zone of Playground Equipment (see
1008.2.6.2).
ASTM F1487-01 Standard Consumer Safety Performance Specification
for Playground Equipment for Public Use (see 106.5).
ASTM F1951-99 Standard Specification for Determination of
Accessibility of Surface Systems Under and Around Playground
Equipment (see 1008.2.6.1).
105.2.4 ICC/IBC. Copies of the referenced standard may be
obtained from the International Code Council, 500 New Jersey Avenue
NW., Washington, DC 20001 (www.iccsafe.org).
International Building Code, 2000 Edition (see 207.1, 207.2,
216.4.2, 216.4.3, and 1005.2.1).
International Building Code, 2001 Supplement (see 207.1 and
207.2).
International Building Code, 2003 Edition (see 207.1, 207.2,
216.4.2, 216.4.3, and 1005.2.1).
105.2.5 NFPA. Copies of the referenced standards may be obtained
from the National Fire Protection Association, 1 Batterymarch Park,
Quincy, Massachusetts 02169 (https://www.nfpa.org).
NFPA 72 National Fire Alarm Code, 1999 Edition (see 702.1 and
809.5.2).
NFPA 72 National Fire Alarm Code, 2002 Edition (see 702.1 and
809.5.2).

106 Definitions

106.1 General. For the purpose of this document, the terms
defined in 106.5 have the indicated meaning.
106.2 Terms Defined in Referenced Standards. Terms not defined
in 106.5 or in regulations issued by the Department of Justice and
the Department of Transportation to implement the Americans with
Disabilities Act, but specifically defined in a referenced standard,
shall have the specified meaning from the referenced standard unless
otherwise stated.
106.3 Undefined Terms. The meaning of terms not specifically
defined in 106.5 or in regulations issued by the Department of
Justice and the Department of Transportation to implement the
Americans with Disabilities Act or in referenced standards shall be
as defined by collegiate dictionaries in the sense that the context
implies.
106.4 Interchangeability. Words, terms and phrases used in the
singular include the plural and those used in the plural include the
singular.
106.5 Defined Terms.
Accessible. A site, building, facility, or portion thereof that
complies with this part.
Accessible Means of Egress. A continuous and unobstructed way of
egress travel from any point in a building or facility that provides
an accessible route to an area of refuge, a horizontal exit, or a
public way.
Addition. An expansion, extension, or increase in the gross
floor area or height of a building or facility.
Administrative Authority. A governmental agency that adopts or
enforces regulations and guidelines for the design, construction, or
alteration of buildings and facilities.
Alteration. A change to a building or facility that affects or
could affect the usability of the building or facility or portion
thereof. Alterations include, but are not limited to, remodeling,
renovation,

[[Page 59496]]

rehabilitation, reconstruction, historic restoration, resurfacing of
circulation paths or vehicular ways, changes or rearrangement of the
structural parts or elements, and changes or rearrangement in the
plan configuration of walls and full-height partitions. Normal
maintenance, reroofing, painting or wallpapering, or changes to
mechanical and electrical systems are not alterations unless they
affect the usability of the building or facility.
Amusement Attraction. Any facility, or portion of a facility,
located within an amusement park or theme park which provides
amusement without the use of an amusement device. Amusement
attractions include, but are not limited to, fun houses, barrels,
and other attractions without seats.
Amusement Ride. A system that moves persons through a fixed
course within a defined area for the purpose of amusement.
Amusement Ride Seat. A seat that is built-in or mechanically
fastened to an amusement ride intended to be occupied by one or more
passengers.
Area of Sport Activity. That portion of a room or space where
the play or practice of a sport occurs.
Assembly Area. A building or facility, or portion thereof, used
for the purpose of entertainment, educational or civic gatherings,
or similar purposes. For the purposes of these requirements,
assembly areas include, but are not limited to, classrooms, lecture
halls, courtrooms, public meeting rooms, public hearing rooms,
legislative chambers, motion picture houses, auditoria, theaters,
playhouses, dinner theaters, concert halls, centers for the
performing arts, amphitheaters, arenas, stadiums, grandstands, or
convention centers.
Assistive Listening System (ALS). An amplification system
utilizing transmitters, receivers, and coupling devices to bypass
the acoustical space between a sound source and a listener by means
of induction loop, radio frequency, infrared, or direct-wired
equipment.
Boarding Pier. A portion of a pier where a boat is temporarily
secured for the purpose of embarking or disembarking.
Boat Launch Ramp. A sloped surface designed for launching and
retrieving trailered boats and other water craft to and from a body
of water.
Boat Slip. That portion of a pier, main pier, finger pier, or
float where a boat is moored for the purpose of berthing, embarking,
or disembarking.
Building. Any structure used or intended for supporting or
sheltering any use or occupancy.
Catch Pool. A pool or designated section of a pool used as a
terminus for water slide flumes.
Characters. Letters, numbers, punctuation marks and typographic
symbols.
Children's Use. Describes spaces and elements specifically
designed for use primarily by people 12 years old and younger.
Circulation Path. An exterior or interior way of passage
provided for pedestrian travel, including but not limited to, walks,
hallways, courtyards, elevators, platform lifts, ramps, stairways,
and landings.
Closed-Circuit Telephone. A telephone with a dedicated line such
as a house phone, courtesy phone or phone that must be used to gain
entry to a facility.
Common Use. Interior or exterior circulation paths, rooms,
spaces, or elements that are not for public use and are made
available for the shared use of two or more people.
Cross Slope. The slope that is perpendicular to the direction of
travel (see running slope).
Curb Ramp. A short ramp cutting through a curb or built up to
it.
Detectable Warning. A standardized surface feature built in or
applied to walking surfaces or other elements to warn of hazards on
a circulation path.
Element. An architectural or mechanical component of a building,
facility, space, or site.
Elevated Play Component. A play component that is approached
above or below grade and that is part of a composite play structure
consisting of two or more play components attached or functionally
linked to create an integrated unit providing more than one play
activity.
Employee Work Area. All or any portion of a space used only by
employees and used only for work. Corridors, toilet rooms,
kitchenettes and break rooms are not employee work areas.
Entrance. Any access point to a building or portion of a
building or facility used for the purpose of entering. An entrance
includes the approach walk, the vertical access leading to the
entrance platform, the entrance platform itself, vestibule if
provided, the entry door or gate, and the hardware of the entry door
or gate.
Facility. All or any portion of buildings, structures, site
improvements, elements, and pedestrian routes or vehicular ways
located on a site.
Gangway. A variable-sloped pedestrian walkway that links a fixed
structure or land with a floating structure. Gangways that connect
to vessels are not addressed by this document.
Golf Car Passage. A continuous passage on which a motorized golf
car can operate.
Ground Level Play Component. A play component that is approached
and exited at the ground level.
Key Station. Rapid and light rail stations, and commuter rail
stations, as defined under criteria established by the Department of
Transportation in 49 CFR 37.47 and 49 CFR 37.51, respectively.
Mail Boxes. Receptacles for the receipt of documents, packages,
or other deliverable matter. Mail boxes include, but are not limited
to, post office boxes and receptacles provided by commercial mail-
receiving agencies, apartment facilities, or schools.
Marked Crossing. A crosswalk or other identified path intended
for pedestrian use in crossing a vehicular way.
Mezzanine. An intermediate level or levels between the floor and
ceiling of any story with an aggregate floor area of not more than
one-third of the area of the room or space in which the level or
levels are located. Mezzanines have sufficient elevation that space
for human occupancy can be provided on the floor below.
Occupant Load. The number of persons for which the means of
egress of a building or portion of a building is designed.
Operable Part. A component of an element used to insert or
withdraw objects, or to activate, deactivate, or adjust the element.
Pictogram. A pictorial symbol that represents activities,
facilities, or concepts.
Play Area. A portion of a site containing play components
designed and constructed for children.
Play Component. An element intended to generate specific
opportunities for play, socialization, or learning. Play components
are manufactured or natural; and are stand-alone or part of a
composite play structure.
Private Building or Facility. A place of public accommodation or
a commercial building or facility subject to title III of the ADA
and 28 CFR part 36 or a transportation building or facility subject
to title III of the ADA and 49 CFR 37.45.
Public Building or Facility. A building or facility or portion
of a building or facility designed, constructed, or altered by, on
behalf of, or for the use of a public entity subject to title II of
the ADA and 28 CFR part 35 or to title II of the ADA and 49 CFR
37.41 or 37.43.
Public Entrance. An entrance that is not a service entrance or a
restricted entrance.
Public Use. Interior or exterior rooms, spaces, or elements that
are made available to the public. Public use may be provided at a
building or facility that is privately or publicly owned.
Public Way. Any street, alley or other parcel of land open to
the outside air leading to a public street, which has been deeded,
dedicated or otherwise permanently appropriated to the public for
public use and which has a clear width and height of not less than
10 feet (3050 mm).
Qualified Historic Building or Facility. A building or facility
that is listed in or eligible for listing in the National Register
of Historic Places, or designated as historic under an appropriate
State or local law.
Ramp. A walking surface that has a running slope steeper than
1:20.
Residential Dwelling Unit. A unit intended to be used as a
residence, that is primarily long-term in nature. Residential
dwelling units do not include transient lodging, inpatient medical
care, licensed long-term care, and detention or correctional
facilities.
Restricted Entrance. An entrance that is made available for
common use on a controlled basis but not public use and that is not
a service entrance.
Running Slope. The slope that is parallel to the direction of
travel (see cross slope).
Self-Service Storage. Building or facility designed and used for
the purpose of renting or leasing individual storage spaces to
customers for the purpose of storing and removing personal property
on a self-service basis.
Service Entrance. An entrance intended primarily for delivery of
goods or services.
Site. A parcel of land bounded by a property line or a
designated portion of a public right-of-way.
Soft Contained Play Structure. A play structure made up of one
or more play components where the user enters a fully

[[Page 59497]]

enclosed play environment that utilizes pliable materials, such as
plastic, netting, or fabric.
Space. A definable area, such as a room, toilet room, hall,
assembly area, entrance, storage room, alcove, courtyard, or lobby.
Story. That portion of a building or facility designed for human
occupancy included between the upper surface of a floor and upper
surface of the floor or roof next above. A story containing one or
more mezzanines has more than one floor level.
Structural Frame. The columns and the girders, beams, and
trusses having direct connections to the columns and all other
members that are essential to the stability of the building or
facility as a whole.
Tactile. An object that can be perceived using the sense of
touch.
Technically Infeasible. With respect to an alteration of a
building or a facility, something that has little likelihood of
being accomplished because existing structural conditions would
require removing or altering a loadbearing member that is an
essential part of the structural frame; or because other existing
physical or site constraints prohibit modification or addition of
elements, spaces, or features that are in full and strict compliance
with the minimum requirements.
Teeing Ground. In golf, the starting place for the hole to be
played.
Transfer Device. Equipment designed to facilitate the transfer
of a person from a wheelchair or other mobility aid to and from an
amusement ride seat.
Transient Lodging. A building or facility containing one or more
guest room(s) for sleeping that provides accommodations that are
primarily short-term in nature. Transient lodging does not include
residential dwelling units intended to be used as a residence,
inpatient medical care facilities, licensed long-term care
facilities, detention or correctional facilities, or private
buildings or facilities that contain not more than five rooms for
rent or hire and that are actually occupied by the proprietor as the
residence of such proprietor.
Transition Plate. A sloping pedestrian walking surface located
at the end(s) of a gangway.
TTY. An abbreviation for teletypewriter. Machinery that employs
interactive text-based communication through the transmission of
coded signals across the telephone network. TTYs may include, for
example, devices known as TDDs (telecommunication display devices or
telecommunication devices for deaf persons) or computers with
special modems. TTYs are also called text telephones.
Use Zone. The ground level area beneath and immediately adjacent
to a play structure or play equipment that is designated by ASTM
F1487 (incorporated by reference, see ``Referenced Standards'' in
Chapter 1) for unrestricted circulation around the play equipment
and where it is predicted that a user would land when falling from
or exiting the play equipment.
Vehicular Way. A route provided for vehicular traffic, such as
in a street, driveway, or parking facility.
Walk. An exterior prepared surface for pedestrian use, including
pedestrian areas such as plazas and courts.
Wheelchair Space. Space for a single wheelchair and its
occupant.
Work Area Equipment. Any machine, instrument, engine, motor,
pump, conveyor, or other apparatus used to perform work. As used in
this document, this term shall apply only to equipment that is
permanently installed or built-in in employee work areas. Work area
equipment does not include passenger elevators and other accessible
means of vertical transportation.

ADA CHAPTER 2: SCOPING REQUIREMENTS

201 Application

201.1 Scope. All areas of newly designed and newly constructed
buildings and facilities and altered portions of existing buildings
and facilities shall comply with these requirements.
201.2 Application Based on Building or Facility Use. Where a
site, building, facility, room, or space contains more than one use,
each portion shall comply with the applicable requirements for that
use.
201.3 Temporary and Permanent Structures. These requirements
shall apply to temporary and permanent buildings and facilities.

202 Existing Buildings and Facilities

202.1 General. Additions and alterations to existing buildings
or facilities shall comply with 202.
202.2 Additions. Each addition to an existing building or
facility shall comply with the requirements for new construction.
Each addition that affects or could affect the usability of or
access to an area containing a primary function shall comply with
202.4.
202.3 Alterations. Where existing elements or spaces are
altered, each altered element or space shall comply with the
applicable requirements of Chapter 2.
EXCEPTIONS: 1. Unless required by 202.4, where elements or
spaces are altered and the circulation path to the altered element
or space is not altered, an accessible route shall not be required.
2. In alterations, where compliance with applicable requirements
is technically infeasible, the alteration shall comply with the
requirements to the maximum extent feasible.
3. Residential dwelling units not required to be accessible in
compliance with a standard issued pursuant to the Americans with
Disabilities Act or Section 504 of the Rehabilitation Act of 1973,
as amended, shall not be required to comply with 202.3.
202.3.1 Prohibited Reduction in Access. An alteration that
decreases or has the effect of decreasing the accessibility of a
building or facility below the requirements for new construction at
the time of the alteration is prohibited.
202.3.2 Extent of Application. An alteration of an existing
element, space, or area of a building or facility shall not impose a
requirement for accessibility greater than required for new
construction.
202.4 Alterations Affecting Primary Function Areas. In addition
to the requirements of 202.3, an alteration that affects or could
affect the usability of or access to an area containing a primary
function shall be made so as to ensure that, to the maximum extent
feasible, the path of travel to the altered area, including the rest
rooms, telephones, and drinking fountains serving the altered area,
are readily accessible to and usable by individuals with
disabilities, unless such alterations are disproportionate to the
overall alterations in terms of cost and scope as determined under
criteria established by the Attorney General. In existing
transportation facilities, an area of primary function shall be as
defined under regulations published by the Secretary of the
Department of Transportation or the Attorney General.
EXCEPTION: Residential dwelling units shall not be required to
comply with 202.4.
202.5 Alterations to Qualified Historic Buildings and
Facilities. Alterations to a qualified historic building or facility
shall comply with 202.3 and 202.4.
EXCEPTION: Where the State Historic Preservation Officer or
Advisory Council on Historic Preservation determines that compliance
with the requirements for accessible routes, entrances, or toilet
facilities would threaten or destroy the historic significance of
the building or facility, the exceptions for alterations to
qualified historic buildings or facilities for that element shall be
permitted to apply.

203 General Exceptions

203.1 General. Sites, buildings, facilities, and elements are
exempt from these requirements to the extent specified by 203.
203.2 Construction Sites. Structures and sites directly
associated with the actual processes of construction, including but
not limited to, scaffolding, bridging, materials hoists, materials
storage, and construction trailers shall not be required to comply
with these requirements or to be on an accessible route. Portable
toilet units provided for use exclusively by construction personnel
on a construction site shall not be required to comply with 213 or
to be on an accessible route.
203.3 Raised Areas. Areas raised primarily for purposes of
security, life safety, or fire safety, including but not limited to,
observation or lookout galleries, prison guard towers, fire towers,
or life guard stands shall not be required to comply with these
requirements or to be on an accessible route.
203.4 Limited Access Spaces. Spaces accessed only by ladders,
catwalks, crawl spaces, or very narrow passageways shall not be
required to comply with these requirements or to be on an accessible
route.
203.5 Machinery Spaces. Spaces frequented only by service
personnel for maintenance, repair, or occasional monitoring of
equipment shall not be required to comply with these requirements or
to be on an accessible route. Machinery spaces include, but are not
limited to, elevator pits or elevator penthouses; mechanical,
electrical or communications equipment rooms; piping or equipment
catwalks; water or sewage treatment pump rooms and stations;
electric substations and transformer vaults; and highway and tunnel
utility facilities.

[[Page 59498]]

203.6 Single Occupant Structures. Single occupant structures
accessed only by passageways below grade or elevated above standard
curb height, including but not limited to, toll booths that are
accessed only by underground tunnels, shall not be required to
comply with these requirements or to be on an accessible route.
203.7 Detention and Correctional Facilities. In detention and
correctional facilities, common use areas that are used only by
inmates or detainees and security personnel and that do not serve
holding cells or housing cells required to comply with 232, shall
not be required to comply with these requirements or to be on an
accessible route.
203.8 Residential Facilities. In residential facilities, common
use areas that do not serve residential dwelling units required to
provide mobility features complying with 809.2 through 809.4 shall
not be required to comply with these requirements or to be on an
accessible route.
203.9 Employee Work Areas. Spaces and elements within employee
work areas shall only be required to comply with 206.2.8, 207.1, and
215.3 and shall be designed and constructed so that individuals with
disabilities can approach, enter, and exit the employee work area.
Employee work areas, or portions of employee work areas, other than
raised courtroom stations, that are less than 300 square feet (28
m²) and elevated 7 inches (180 mm) or more above the
finish floor or ground where the elevation is essential to the
function of the space shall not be required to comply with these
requirements or to be on an accessible route.
203.10 Raised Refereeing, Judging, and Scoring Areas. Raised
structures used solely for refereeing, judging, or scoring a sport
shall not be required to comply with these requirements or to be on
an accessible route.
203.11 Water Slides. Water slides shall not be required to
comply with these requirements or to be on an accessible route.
203.12 Animal Containment Areas. Animal containment areas that
are not for public use shall not be required to comply with these
requirements or to be on an accessible route.
203.13 Raised Boxing or Wrestling Rings. Raised boxing or
wrestling rings shall not be required to comply with these
requirements or to be on an accessible route.
203.14 Raised Diving Boards and Diving Platforms. Raised diving
boards and diving platforms shall not be required to comply with
these requirements or to be on an accessible route.

204 Protruding Objects

204.1 General. Protruding objects on circulation paths shall
comply with 307.
EXCEPTIONS: 1. Within areas of sport activity, protruding
objects on circulation paths shall not be required to comply with
307.
2. Within play areas, protruding objects on circulation paths
shall not be required to comply with 307 provided that ground level
accessible routes provide vertical clearance in compliance with
1008.2.

205 Operable Parts

205.1 General. Operable parts on accessible elements, accessible
routes, and in accessible rooms and spaces shall comply with 309.
EXCEPTIONS: 1. Operable parts that are intended for use only by
service or maintenance personnel shall not be required to comply
with 309.
2. Electrical or communication receptacles serving a dedicated
use shall not be required to comply with 309.
3. Where two or more outlets are provided in a kitchen above a
length of counter top that is uninterrupted by a sink or appliance,
one outlet shall not be required to comply with 309.
4. Floor electrical receptacles shall not be required to comply
with 309.
5. HVAC diffusers shall not be required to comply with 309.
6. Except for light switches, where redundant controls are
provided for a single element, one control in each space shall not
be required to comply with 309.
7. Cleats and other boat securement devices shall not be
required to comply with 309.3.
8. Exercise machines and exercise equipment shall not be
required to comply with 309.

206 Accessible Routes

206.1 General. Accessible routes shall be provided in accordance
with 206 and shall comply with Chapter 4.
206.2 Where Required. Accessible routes shall be provided where
required by 206.2.
206.2.1 Site Arrival Points. At least one accessible route shall
be provided within the site from accessible parking spaces and
accessible passenger loading zones; public streets and sidewalks;
and public transportation stops to the accessible building or
facility entrance they serve.
EXCEPTIONS: 1. Where exceptions for alterations to qualified
historic buildings or facilities are permitted by 202.5, no more
than one accessible route from a site arrival point to an accessible
entrance shall be required.
2. An accessible route shall not be required between site
arrival points and the building or facility entrance if the only
means of access between them is a vehicular way not providing
pedestrian access.
206.2.2 Within a Site. At least one accessible route shall
connect accessible buildings, accessible facilities, accessible
elements, and accessible spaces that are on the same site.
EXCEPTION: An accessible route shall not be required between
accessible buildings, accessible facilities, accessible elements,
and accessible spaces if the only means of access between them is a
vehicular way not providing pedestrian access.
206.2.3 Multi-Story Buildings and Facilities. At least one
accessible route shall connect each story and mezzanine in multi-
story buildings and facilities.
EXCEPTIONS: 1. In private buildings or facilities that are less
than three stories or that have less than 3000 square feet (279
m²) per story, an accessible route shall not be required
to connect stories provided that the building or facility is not a
shopping center, a shopping mall, the professional office of a
health care provider, a terminal, depot or other station used for
specified public transportation, an airport passenger terminal, or
another type of facility as determined by the Attorney General.
2. Where a two-story public building or facility has one story
with an occupant load of five or fewer persons that does not contain
public use space, that story shall not be required to be connected
to the story above or below.
3. In detention and correctional facilities, an accessible route
shall not be required to connect stories where cells with mobility
features required to comply with 807.2, all common use areas serving
cells with mobility features required to comply with 807.2, and all
public use areas are on an accessible route.
4. In residential facilities, an accessible route shall not be
required to connect stories where residential dwelling units with
mobility features required to comply with 809.2 through 809.4, all
common use areas serving residential dwelling units with mobility
features required to comply with 809.2 through 809.4, and public use
areas serving residential dwelling units are on an accessible route.
5. Within multi-story transient lodging guest rooms with
mobility features required to comply with 806.2, an accessible route
shall not be required to connect stories provided that spaces
complying with 806.2 are on an accessible route and sleeping
accommodations for two persons minimum are provided on a story
served by an accessible route.
6. In air traffic control towers, an accessible route shall not
be required to serve the cab and the floor immediately below the
cab.
7. Where exceptions for alterations to qualified historic
buildings or facilities are permitted by 202.5, an accessible route
shall not be required to stories located above or below the
accessible story.
206.2.3.1 Stairs and Escalators in Existing Buildings. In
alterations and additions, where an escalator or stair is provided
where none existed previously and major structural modifications are
necessary for the installation, an accessible route shall be
provided between the levels served by the escalator or stair unless
exempted by 206.2.3 Exceptions 1 through 7.
206.2.4 Spaces and Elements. At least one accessible route shall
connect accessible building or facility entrances with all
accessible spaces and elements within the building or facility which
are otherwise connected by a circulation path unless exempted by
206.2.3 Exceptions 1 through 7.
EXCEPTIONS: 1. Raised courtroom stations, including judges'
benches, clerks' stations, bailiffs' stations, deputy clerks'
stations, and court reporters' stations shall not be required to
provide vertical access provided that the required clear floor
space, maneuvering space, and, if appropriate, electrical service
are installed at the time of initial construction to allow future
installation of a means of vertical access complying with 405, 407,
408, or 410 without requiring substantial reconstruction of the
space.
2. In assembly areas with fixed seating required to comply with
221, an accessible

[[Page 59499]]

route shall not be required to serve fixed seating where wheelchair
spaces required to be on an accessible route are not provided.
3. Accessible routes shall not be required to connect mezzanines
where buildings or facilities have no more than one story. In
addition, accessible routes shall not be required to connect stories
or mezzanines where multi-story buildings or facilities are exempted
by 206.2.3 Exceptions 1 through 7.
206.2.5 Restaurants and Cafeterias. In restaurants and
cafeterias, an accessible route shall be provided to all dining
areas, including raised or sunken dining areas, and outdoor dining
areas.
EXCEPTIONS: 1. In buildings or facilities not required to
provide an accessible route between stories, an accessible route
shall not be required to a mezzanine dining area where the mezzanine
contains less than 25 percent of the total combined area for seating
and dining and where the same decor and services are provided in the
accessible area.
2. In alterations, an accessible route shall not be required to
existing raised or sunken dining areas, or to all parts of existing
outdoor dining areas where the same services and decor are provided
in an accessible space usable by the public and not restricted to
use by people with disabilities.
3. In sports facilities, tiered dining areas providing seating
required to comply with 221 shall be required to have accessible
routes serving at least 25 percent of the dining area provided that
accessible routes serve seating complying with 221 and each tier is
provided with the same services.
206.2.6 Performance Areas. Where a circulation path directly
connects a performance area to an assembly seating area, an
accessible route shall directly connect the assembly seating area
with the performance area. An accessible route shall be provided
from performance areas to ancillary areas or facilities used by
performers unless exempted by 206.2.3 Exceptions 1 through 7.
206.2.7 Press Boxes. Press boxes in assembly areas shall be on
an accessible route.
EXCEPTIONS: 1. An accessible route shall not be required to
press boxes in bleachers that have points of entry at only one level
provided that the aggregate area of all press boxes is 500 square
feet (46 m²) maximum.
2. An accessible route shall not be required to free-standing
press boxes that are elevated above grade 12 feet (3660 mm) minimum
provided that the aggregate area of all press boxes is 500 square
feet (46 m²) maximum.
206.2.8 Employee Work Areas. Common use circulation paths within
employee work areas shall comply with 402.
EXCEPTIONS: 1. Common use circulation paths located within
employee work areas that are less than 1000 square feet (93
m²) and defined by permanently installed partitions,
counters, casework, or furnishings shall not be required to comply
with 402.
2. Common use circulation paths located within employee work
areas that are an integral component of work area equipment shall
not be required to comply with 402.
3. Common use circulation paths located within exterior employee
work areas that are fully exposed to the weather shall not be
required to comply with 402.
206.2.9 Amusement Rides. Amusement rides required to comply with
234 shall provide accessible routes in accordance with 206.2.9.
Accessible routes serving amusement rides shall comply with Chapter
4 except as modified by 1002.2.
206.2.9.1 Load and Unload Areas. Load and unload areas shall be
on an accessible route. Where load and unload areas have more than
one loading or unloading position, at least one loading and
unloading position shall be on an accessible route.
206.2.9.2 Wheelchair Spaces, Ride Seats Designed for Transfer,
and Transfer Devices. When amusement rides are in the load and
unload position, wheelchair spaces complying with 1002.4, amusement
ride seats designed for transfer complying with 1002.5, and transfer
devices complying with 1002.6 shall be on an accessible route.
206.2.10 Recreational Boating Facilities. Boat slips required to
comply with 235.2 and boarding piers at boat launch ramps required
to comply with 235.3 shall be on an accessible route. Accessible
routes serving recreational boating facilities shall comply with
Chapter 4, except as modified by 1003.2.
206.2.11 Bowling Lanes. Where bowling lanes are provided, at
least 5 percent, but no fewer than one of each type of bowling lane,
shall be on an accessible route.
206.2.12 Court Sports. In court sports, at least one accessible
route shall directly connect both sides of the court.
206.2.13 Exercise Machines and Equipment. Exercise machines and
equipment required to comply with 236 shall be on an accessible
route.
206.2.14 Fishing Piers and Platforms. Fishing piers and
platforms shall be on an accessible route. Accessible routes serving
fishing piers and platforms shall comply with Chapter 4 except as
modified by 1005.1.
206.2.15 Golf Facilities. At least one accessible route shall
connect accessible elements and spaces within the boundary of the
golf course. In addition, accessible routes serving golf car rental
areas; bag drop areas; course weather shelters complying with
238.2.3; course toilet rooms; and practice putting greens, practice
teeing grounds, and teeing stations at driving ranges complying with
238.3 shall comply with Chapter 4 except as modified by 1006.2.
EXCEPTION: Golf car passages complying with 1006.3 shall be
permitted to be used for all or part of accessible routes required
by 206.2.15.
206.2.16 Miniature Golf Facilities. Holes required to comply
with 239.2, including the start of play, shall be on an accessible
route. Accessible routes serving miniature golf facilities shall
comply with Chapter 4 except as modified by 1007.2.
206.2.17 Play Areas. Play areas shall provide accessible routes
in accordance with 206.2.17. Accessible routes serving play areas
shall comply with Chapter 4 except as modified by 1008.2.
206.2.17.1 Ground Level and Elevated Play Components. At least
one accessible route shall be provided within the play area. The
accessible route shall connect ground level play components required
to comply with 240.2.1 and elevated play components required to
comply with 240.2.2, including entry and exit points of the play
components.
206.2.17.2 Soft Contained Play Structures. Where three or fewer
entry points are provided for soft contained play structures, at
least one entry point shall be on an accessible route. Where four or
more entry points are provided for soft contained play structures,
at least two entry points shall be on an accessible route.
206.3 Location. Accessible routes shall coincide with or be
located in the same area as general circulation paths. Where
circulation paths are interior, required accessible routes shall
also be interior.
206.4 Entrances. Entrances shall be provided in accordance with
206.4. Entrance doors, doorways, and gates shall comply with 404 and
shall be on an accessible route complying with 402.
EXCEPTIONS: 1. Where an alteration includes alterations to an
entrance, and the building or facility has another entrance
complying with 404 that is on an accessible route, the altered
entrance shall not be required to comply with 206.4 unless required
by 202.4.
2. Where exceptions for alterations to qualified historic
buildings or facilities are permitted by 202.5, no more than one
public entrance shall be required to comply with 206.4. Where no
public entrance can comply with 206.4 under criteria established in
202.5 Exception, then either an unlocked entrance not used by the
public shall comply with 206.4; or a locked entrance complying with
206.4 with a notification system or remote monitoring shall be
provided.
206.4.1 Public Entrances. In addition to entrances required by
206.4.2 through 206.4.9, at least 60 percent of all public entrances
shall comply with 404.
206.4.2 Parking Structure Entrances. Where direct access is
provided for pedestrians from a parking structure to a building or
facility entrance, each direct access to the building or facility
entrance shall comply with 404.
206.4.3 Entrances from Tunnels or Elevated Walkways. Where
direct access is provided for pedestrians from a pedestrian tunnel
or elevated walkway to a building or facility, at least one direct
entrance to the building or facility from each tunnel or walkway
shall comply with 404.
206.4.4 Transportation Facilities. In addition to the
requirements of 206.4.2, 206.4.3, and 206.4.5 through 206.4.9,
transportation facilities shall provide entrances in accordance with
206.4.4.
206.4.4.1 Location. In transportation facilities, where
different entrances serve different transportation fixed routes or
groups of fixed routes, at least one public entrance serving each
fixed route or group of fixed routes shall comply with 404.
EXCEPTION: Entrances to key stations and existing intercity rail
stations retrofitted in accordance with 49 CFR 37.49 or 49 CFR 37.51
shall not be required to comply with 206.4.4.1.
206.4.4.2 Direct Connections. Direct connections to other
facilities shall provide an accessible route complying with 404 from
the point of connection to boarding platforms and all transportation
system elements

[[Page 59500]]

required to be accessible. Any elements provided to facilitate
future direct connections shall be on an accessible route connecting
boarding platforms and all transportation system elements required
to be accessible.
EXCEPTION: In key stations and existing intercity rail stations,
existing direct connections shall not be required to comply with
404.
206.4.4.3 Key Stations and Intercity Rail Stations. Key stations
and existing intercity rail stations required by Subpart C of 49 CFR
part 37 to be altered, shall have at least one entrance complying
with 404.
206.4.5 Tenant Spaces. At least one accessible entrance to each
tenancy in a facility shall comply with 404.
EXCEPTION: Self-service storage facilities not required to
comply with 225.3 shall not be required to be on an accessible
route.
206.4.6 Residential Dwelling Unit Primary Entrance. In
residential dwelling units, at least one primary entrance shall
comply with 404. The primary entrance to a residential dwelling unit
shall not be to a bedroom.
206.4.7 Restricted Entrances. Where restricted entrances are
provided to a building or facility, at least one restricted entrance
to the building or facility shall comply with 404.
206.4.8 Service Entrances. If a service entrance is the only
entrance to a building or to a tenancy in a facility, that entrance
shall comply with 404.
206.4.9 Entrances for Inmates or Detainees. Where entrances used
only by inmates or detainees and security personnel are provided at
judicial facilities, detention facilities, or correctional
facilities, at least one such entrance shall comply with 404.
206.5 Doors, Doorways, and Gates. Doors, doorways, and gates
providing user passage shall be provided in accordance with 206.5.
206.5.1 Entrances. Each entrance to a building or facility
required to comply with 206.4 shall have at least one door, doorway,
or gate complying with 404.
206.5.2 Rooms and Spaces. Within a building or facility, at
least one door, doorway, or gate serving each room or space
complying with these requirements shall comply with 404.
206.5.3 Transient Lodging Facilities. In transient lodging
facilities, entrances, doors, and doorways providing user passage
into and within guest rooms that are not required to provide
mobility features complying with 806.2 shall comply with 404.2.3.
EXCEPTION: Shower and sauna doors in guest rooms that are not
required to provide mobility features complying with 806.2 shall not
be required to comply with 404.2.3.
206.5.4 Residential Dwelling Units. In residential dwelling
units required to provide mobility features complying with 809.2
through 809.4, all doors and doorways providing user passage shall
comply with 404.
206.6 Elevators. Elevators provided for passengers shall comply
with 407. Where multiple elevators are provided, each elevator shall
comply with 407.
EXCEPTIONS: 1. In a building or facility permitted to use the
exceptions to 206.2.3 or permitted by 206.7 to use a platform lift,
elevators complying with 408 shall be permitted.
2. Elevators complying with 408 or 409 shall be permitted in
multi-story residential dwelling units.
206.6.1 Existing Elevators. Where elements of existing elevators
are altered, the same element shall also be altered in all elevators
that are programmed to respond to the same hall call control as the
altered elevator and shall comply with the requirements of 407 for
the altered element.
206.7 Platform Lifts. Platform lifts shall comply with 410.
Platform lifts shall be permitted as a component of an accessible
route in new construction in accordance with 206.7. Platform lifts
shall be permitted as a component of an accessible route in an
existing building or facility.
206.7.1 Performance Areas and Speakers' Platforms. Platform
lifts shall be permitted to provide accessible routes to performance
areas and speakers' platforms.
206.7.2 Wheelchair Spaces. Platform lifts shall be permitted to
provide an accessible route to comply with the wheelchair space
dispersion and line-of-sight requirements of 221 and 802.
206.7.3 Incidental Spaces. Platform lifts shall be permitted to
provide an accessible route to incidental spaces which are not
public use spaces and which are occupied by five persons maximum.
206.7.4 Judicial Spaces. Platform lifts shall be permitted to
provide an accessible route to: jury boxes and witness stands;
raised courtroom stations including, judges' benches, clerks'
stations, bailiffs' stations, deputy clerks' stations, and court
reporters' stations; and to depressed areas such as the well of a
court.
206.7.5 Existing Site Constraints. Platform lifts shall be
permitted where existing exterior site constraints make use of a
ramp or elevator infeasible.
206.7.6 Guest Rooms and Residential Dwelling Units. Platform
lifts shall be permitted to connect levels within transient lodging
guest rooms required to provide mobility features complying with
806.2 or residential dwelling units required to provide mobility
features complying with 809.2 through 809.4.
206.7.7 Amusement Rides. Platform lifts shall be permitted to
provide accessible routes to load and unload areas serving amusement
rides.
206.7.8 Play Areas. Platform lifts shall be permitted to provide
accessible routes to play components or soft contained play
structures.
206.7.9 Team or Player Seating. Platform lifts shall be
permitted to provide accessible routes to team or player seating
areas serving areas of sport activity.
206.7.10 Recreational Boating Facilities and Fishing Piers and
Platforms. Platform lifts shall be permitted to be used instead of
gangways that are part of accessible routes serving recreational
boating facilities and fishing piers and platforms.
206.8 Security Barriers. Security barriers, including but not
limited to, security bollards and security check points, shall not
obstruct a required accessible route or accessible means of egress.
EXCEPTION: Where security barriers incorporate elements that
cannot comply with these requirements such as certain metal
detectors, fluoroscopes, or other similar devices, the accessible
route shall be permitted to be located adjacent to security
screening devices. The accessible route shall permit persons with
disabilities passing around security barriers to maintain visual
contact with their personal items to the same extent provided others
passing through the security barrier.

207 Accessible Means of Egress

207.1 General. Means of egress shall comply with section
1003.2.13 of the International Building Code (2000 edition and 2001
Supplement) or section 1007 of the International Building Code (2003
edition) (incorporated by reference, see Referenced Standards'' in
Chapter 1).
EXCEPTIONS: 1. Where means of egress are permitted by local
building or life safety codes to share a common path of egress
travel, accessible means of egress shall be permitted to share a
common path of egress travel.
2. Areas of refuge shall not be required in detention and
correctional facilities.
207.2 Platform Lifts. Standby power shall be provided for
platform lifts permitted by section 1003.2.13.4 of the International
Building Code (2000 edition and 2001 Supplement) or section 1007.5
of the International Building Code (2003 edition) (incorporated by
reference, see ``Referenced Standards'' in Chapter 1) to serve as a
part of an accessible means of egress.

208 Parking Spaces

208.1 General. Where parking spaces are provided, parking spaces
shall be provided in accordance with 208.
EXCEPTION: Parking spaces used exclusively for buses, trucks,
other delivery vehicles, law enforcement vehicles, or vehicular
impound shall not be required to comply with 208 provided that lots
accessed by the public are provided with a passenger loading zone
complying with 503.
208.2 Minimum Number. Parking spaces complying with 502 shall be
provided in accordance with Table 208.2 except as required by
208.2.1, 208.2.2, and 208.2.3. Where more than one parking facility
is provided on a site, the number of accessible spaces provided on
the site shall be calculated according to the number of spaces
required for each parking facility.

Table 208.2--Parking Spaces
------------------------------------------------------------------------
Total number of parking spaces provided in Minimum number of required
parking facility accessible parking spaces
------------------------------------------------------------------------
1 to 25................................... 1
26 to 50.................................. 2
51 to 75.................................. 3
76 to 100................................. 4
101 to 150................................ 5
151 to 200................................ 6
201 to 300................................ 7
301 to 400................................ 8
401 to 500................................ 9
501 to 1000............................... 2 percent of total.

[[Page 59501]]

1001 and over............................. 20, plus 1 for each 100, or
fraction thereof, over
1000.
------------------------------------------------------------------------

208.2.1 Hospital Outpatient Facilities. Ten percent of patient
and visitor parking spaces provided to serve hospital outpatient
facilities shall comply with 502.
208.2.2 Rehabilitation Facilities and Outpatient Physical
Therapy Facilities. Twenty percent of patient and visitor parking
spaces provided to serve rehabilitation facilities specializing in
treating conditions that affect mobility and outpatient physical
therapy facilities shall comply with 502.
208.2.3 Residential Facilities. Parking spaces provided to serve
residential facilities shall comply with 208.2.3.
208.2.3.1 Parking for Residents. Where at least one parking
space is provided for each residential dwelling unit, at least one
parking space complying with 502 shall be provided for each
residential dwelling unit required to provide mobility features
complying with 809.2 through 809.4.
208.2.3.2 Additional Parking Spaces for Residents. Where the
total number of parking spaces provided for each residential
dwelling unit exceeds one parking space per residential dwelling
unit, 2 percent, but no fewer than one space, of all the parking
spaces not covered by 208.2.3.1 shall comply with 502.
208.2.3.3 Parking for Guests, Employees, and Other Non-
Residents. Where parking spaces are provided for persons other than
residents, parking shall be provided in accordance with Table 208.2.
208.2.4 Van Parking Spaces. For every six or fraction of six
parking spaces required by 208.2 to comply with 502, at least one
shall be a van parking space complying with 502.
208.3 Location. Parking facilities shall comply with 208.3.
208.3.1 General. Parking spaces complying with 502 that serve a
particular building or facility shall be located on the shortest
accessible route from parking to an entrance complying with 206.4.
Where parking serves more than one accessible entrance, parking
spaces complying with 502 shall be dispersed and located on the
shortest accessible route to the accessible entrances. In parking
facilities that do not serve a particular building or facility,
parking spaces complying with 502 shall be located on the shortest
accessible route to an accessible pedestrian entrance of the parking
facility.
EXCEPTIONS: 1. All van parking spaces shall be permitted to be
grouped on one level within a multi-story parking facility.
2. Parking spaces shall be permitted to be located in different
parking facilities if substantially equivalent or greater
accessibility is provided in terms of distance from an accessible
entrance or entrances, parking fee, and user convenience.
208.3.2 Residential Facilities. In residential facilities
containing residential dwelling units required to provide mobility
features complying with 809.2 through 809.4, parking spaces provided
in accordance with 208.2.3.1 shall be located on the shortest
accessible route to the residential dwelling unit entrance they
serve. Spaces provided in accordance with 208.2.3.2 shall be
dispersed throughout all types of parking provided for the
residential dwelling units.
EXCEPTION: Parking spaces provided in accordance with 208.2.3.2
shall not be required to be dispersed throughout all types of
parking if substantially equivalent or greater accessibility is
provided in terms of distance from an accessible entrance, parking
fee, and user convenience.

209 Passenger Loading Zones and Bus Stops

209.1 General. Passenger loading zones shall be provided in
accordance with 209.
209.2 Type. Where provided, passenger loading zones shall comply
with 209.2.
209.2.1 Passenger Loading Zones. Passenger loading zones, except
those required to comply with 209.2.2 and 209.2.3, shall provide at
least one passenger loading zone complying with 503 in every
continuous 100 linear feet (30 m) of loading zone space, or fraction
thereof.
209.2.2 Bus Loading Zones. In bus loading zones restricted to
use by designated or specified public transportation vehicles, each
bus bay, bus stop, or other area designated for lift or ramp
deployment shall comply with 810.2.
209.2.3 On-Street Bus Stops. On-street bus stops shall comply
with 810.2 to the maximum extent practicable.
209.3 Medical Care and Long-Term Care Facilities. At least one
passenger loading zone complying with 503 shall be provided at an
accessible entrance to licensed medical care and licensed long-term
care facilities where the period of stay exceeds twenty-four hours.
209.4 Valet Parking. Parking facilities that provide valet
parking services shall provide at least one passenger loading zone
complying with 503.
209.5 Mechanical Access Parking Garages. Mechanical access
parking garages shall provide at least one passenger loading zone
complying with 503 at vehicle drop-off and vehicle pick-up areas.

210 Stairways

210.1 General. Interior and exterior stairs that are part of a
means of egress shall comply with 504.
EXCEPTIONS: 1. In detention and correctional facilities, stairs
that are not located in public use areas shall not be required to
comply with 504.
2. In alterations, stairs between levels that are connected by
an accessible route shall not be required to comply with 504, except
that handrails complying with 505 shall be provided when the stairs
are altered.
3. In assembly areas, aisle stairs shall not be required to
comply with 504.
4. Stairs that connect play components shall not be required to
comply with 504.

211 Drinking Fountains

211.1 General. Where drinking fountains are provided on an
exterior site, on a floor, or within a secured area they shall be
provided in accordance with 211.
EXCEPTION: In detention or correctional facilities, drinking
fountains only serving holding or housing cells not required to
comply with 232 shall not be required to comply with 211.
211.2 Minimum Number. No fewer than two drinking fountains shall
be provided. One drinking fountain shall comply with 602.1 through
602.6 and one drinking fountain shall comply with 602.7.
EXCEPTION: Where a single drinking fountain complies with 602.1
through 602.6 and 602.7, it shall be permitted to be substituted for
two separate drinking fountains.
211.3 More Than Minimum Number. Where more than the minimum
number of drinking fountains specified in 211.2 are provided, 50
percent of the total number of drinking fountains provided shall
comply with 602.1 through 602.6, and 50 percent of the total number
of drinking fountains provided shall comply with 602.7.
EXCEPTION: Where 50 percent of the drinking fountains yields a
fraction, 50 percent shall be permitted to be rounded up or down
provided that the total number of drinking fountains complying with
211 equals 100 percent of drinking fountains.

212 Kitchens, Kitchenettes, and Sinks

212.1 General. Where provided, kitchens, kitchenettes, and sinks
shall comply with 212.
212.2 Kitchens and Kitchenettes. Kitchens and kitchenettes shall
comply with 804.
212.3 Sinks. Where sinks are provided, at least 5 percent, but
no fewer than one, of each type provided in each accessible room or
space shall comply with 606.
EXCEPTION: Mop or service sinks shall not be required to comply
with 212.3.

213 Toilet Facilities and Bathing Facilities

213.1 General. Where toilet facilities and bathing facilities
are provided, they shall comply with 213. Where toilet facilities
and bathing facilities are provided in facilities permitted by
206.2.3 Exceptions 1 and 2 not to connect stories by an accessible
route, toilet facilities and bathing facilities shall be provided on
a story connected by an accessible route to an accessible entrance.
213.2 Toilet Rooms and Bathing Rooms. Where toilet rooms are
provided, each toilet room shall comply with 603. Where bathing
rooms are provided, each bathing room shall comply with 603.
EXCEPTIONS: 1. In alterations where it is technically infeasible
to comply with 603, altering existing toilet or bathing rooms shall
not be required where a single unisex toilet room or bathing room
complying with 213.2.1 is provided and located in the same area and
on the same floor as existing inaccessible toilet or bathing rooms.
2. Where exceptions for alterations to qualified historic
buildings or facilities are permitted by 202.5, no fewer than one
toilet room for each sex complying with 603 or one unisex toilet
room complying with 213.2.1 shall be provided.
3. Where multiple single user portable toilet or bathing units
are clustered at a single

[[Page 59502]]

location, no more than 5 percent of the toilet units and bathing
units at each cluster shall be required to comply with 603. Portable
toilet units and bathing units complying with 603 shall be
identified by the International Symbol of Accessibility complying
with 703.7.2.1.
4. Where multiple single user toilet rooms are clustered at a
single location, no more than 50 percent of the single user toilet
rooms for each use at each cluster shall be required to comply with
603.
213.2.1 Unisex (Single-Use or Family) Toilet and Unisex Bathing
Rooms. Unisex toilet rooms shall contain not more than one lavatory,
and two water closets without urinals or one water closet and one
urinal. Unisex bathing rooms shall contain one shower or one shower
and one bathtub, one lavatory, and one water closet. Doors to unisex
toilet rooms and unisex bathing rooms shall have privacy latches.
213.3 Plumbing Fixtures and Accessories. Plumbing fixtures and
accessories provided in a toilet room or bathing room required to
comply with 213.2 shall comply with 213.3.
213.3.1 Toilet Compartments. Where toilet compartments are
provided, at least one toilet compartment shall comply with 604.8.1.
In addition to the compartment required to comply with 604.8.1, at
least one compartment shall comply with 604.8.2 where six or more
toilet compartments are provided, or where the combination of
urinals and water closets totals six or more fixtures.
213.3.2 Water Closets. Where water closets are provided, at
least one shall comply with 604.
213.3.3 Urinals. Where more than one urinal is provided, at
least one shall comply with 605.
213.3.4 Lavatories. Where lavatories are provided, at least one
shall comply with 606 and shall not be located in a toilet
compartment.
213.3.5 Mirrors. Where mirrors are provided, at least one shall
comply with 603.3.
213.3.6 Bathing Facilities. Where bathtubs or showers are
provided, at least one bathtub complying with 607 or at least one
shower complying with 608 shall be provided.
213.3.7 Coat Hooks and Shelves. Where coat hooks or shelves are
provided in toilet rooms without toilet compartments, at least one
of each type shall comply with 603.4. Where coat hooks or shelves
are provided in toilet compartments, at least one of each type
complying with 604.8.3 shall be provided in toilet compartments
required to comply with 213.3.1. Where coat hooks or shelves are
provided in bathing facilities, at least one of each type complying
with 603.4 shall serve fixtures required to comply with 213.3.6.

214 Washing Machines and Clothes Dryers

214.1 General. Where provided, washing machines and clothes
dryers shall comply with 214.
214.2 Washing Machines. Where three or fewer washing machines
are provided, at least one shall comply with 611. Where more than
three washing machines are provided, at least two shall comply with
611.
214.3 Clothes Dryers. Where three or fewer clothes dryers are
provided, at least one shall comply with 611. Where more than three
clothes dryers are provided, at least two shall comply with 611.

215 Fire Alarm Systems

215.1 General. Where fire alarm systems provide audible alarm
coverage, alarms shall comply with 215.
EXCEPTION: In existing facilities, visible alarms shall not be
required except where an existing fire alarm system is upgraded or
replaced, or a new fire alarm system is installed.
215.2 Public and Common Use Areas. Alarms in public use areas
and common use areas shall comply with 702.
215.3 Employee Work Areas. Where employee work areas have
audible alarm coverage, the wiring system shall be designed so that
visible alarms complying with 702 can be integrated into the alarm
system.
215.4 Transient Lodging. Guest rooms required to comply with
224.4 shall provide alarms complying with 702.
215.5 Residential Facilities. Where provided in residential
dwelling units required to comply with 809.5, alarms shall comply
with 702.

216 Signs

216.1 General. Signs shall be provided in accordance with 216
and shall comply with 703.
EXCEPTIONS: 1. Building directories, menus, seat and row
designations in assembly areas, occupant names, building addresses,
and company names and logos shall not be required to comply with
216.
2. In parking facilities, signs shall not be required to comply
with 216.2, 216.3, and 216.6 through 216.12.
3. Temporary, 7 days or less, signs shall not be required to
comply with 216.
4. In detention and correctional facilities, signs not located
in public use areas shall not be required to comply with 216.
216.2 Designations. Interior and exterior signs identifying
permanent rooms and spaces shall comply with 703.1, 703.2, and
703.5. Where pictograms are provided as designations of permanent
interior rooms and spaces, the pictograms shall comply with 703.6
and shall have text descriptors complying with 703.2 and 703.5.
EXCEPTION: Exterior signs that are not located at the door to
the space they serve shall not be required to comply with 703.2.
216.3 Directional and Informational Signs. Signs that provide
direction to or information about interior spaces and facilities of
the site shall comply with 703.5.
216.4 Means of Egress. Signs for means of egress shall comply
with 216.4.
216.4.1 Exit Doors. Doors at exit passageways, exit discharge,
and exit stairways shall be identified by tactile signs complying
with 703.1, 703.2, and 703.5.
216.4.2 Areas of Refuge. Signs required by section 1003.2.13.5.4
of the International Building Code (2000 edition) or section
1007.6.4 of the International Building Code (2003 edition)
(incorporated by reference, see ``Referenced Standards'' in Chapter
1) to provide instructions in areas of refuge shall comply with
703.5.
216.4.3 Directional Signs. Signs required by section 1003.2.13.6
of the International Building Code (2000 edition) or section 1007.7
of the International Building Code (2003 edition) (incorporated by
reference, see ``Referenced Standards'' in Chapter 1) to provide
directions to accessible means of egress shall comply with 703.5.
216.5 Parking. Parking spaces complying with 502 shall be
identified by signs complying with 502.6.
EXCEPTIONS: 1. Where a total of four or fewer parking spaces,
including accessible parking spaces, are provided on a site,
identification of accessible parking spaces shall not be required.
2. In residential facilities, where parking spaces are assigned
to specific residential dwelling units, identification of accessible
parking spaces shall not be required.
216.6 Entrances. Where not all entrances comply with 404,
entrances complying with 404 shall be identified by the
International Symbol of Accessibility complying with 703.7.2.1.
Directional signs complying with 703.5 that indicate the location of
the nearest entrance complying with 404 shall be provided at
entrances that do not comply with 404.
216.7 Elevators. Where existing elevators do not comply with
407, elevators complying with 407 shall be clearly identified with
the International Symbol of Accessibility complying with 703.7.2.1.
216.8 Toilet Rooms and Bathing Rooms. Where existing toilet
rooms or bathing rooms do not comply with 603, directional signs
indicating the location of the nearest toilet room or bathing room
complying with 603 within the facility shall be provided. Signs
shall comply with 703.5 and shall include the International Symbol
of Accessibility complying with 703.7.2.1. Where existing toilet
rooms or bathing rooms do not comply with 603, the toilet rooms or
bathing rooms complying with 603 shall be identified by the
International Symbol of Accessibility complying with 703.7.2.1.
Where clustered single user toilet rooms or bathing facilities are
permitted to use exceptions to 213.2, toilet rooms or bathing
facilities complying with 603 shall be identified by the
International Symbol of Accessibility complying with 703.7.2.1
unless all toilet rooms and bathing facilities comply with 603.
216.9 TTYs. Identification and directional signs for public TTYs
shall be provided in accordance with 216.9.
216.9.1 Identification Signs. Public TTYs shall be identified by
the International Symbol of TTY complying with 703.7.2.2.
216.9.2 Directional Signs. Directional signs indicating the
location of the nearest public TTY shall be provided at all banks of
public pay telephones not containing a public TTY. In addition,
where signs provide direction to public pay telephones, they shall
also provide direction to public TTYs. Directional signs shall
comply with 703.5 and shall include the International Symbol of TTY
complying with 703.7.2.2.
216.10 Assistive Listening Systems. Each assembly area required
by 219 to provide assistive listening systems shall provide signs
informing patrons of the availability of the

[[Page 59503]]

assistive listening system. Assistive listening signs shall comply
with 703.5 and shall include the International Symbol of Access for
Hearing Loss complying with 703.7.2.4.
EXCEPTION: Where ticket offices or windows are provided, signs
shall not be required at each assembly area provided that signs are
displayed at each ticket office or window informing patrons of the
availability of assistive listening systems.
216.11 Check-Out Aisles. Where more than one check-out aisle is
provided, check-out aisles complying with 904.3 shall be identified
by the International Symbol of Accessibility complying with
703.7.2.1. Where check-out aisles are identified by numbers,
letters, or functions, signs identifying check-out aisles complying
with 904.3 shall be located in the same location as the checkout
aisle identification.
EXCEPTION: Where all check-out aisles serving a single function
comply with 904.3, signs complying with 703.7.2.1 shall not be
required.
216.12 Amusement Rides. Signs identifying the type of access
provided on amusement rides shall be provided at entries to queues
and waiting lines. In addition, where accessible unload areas also
serve as accessible load areas, signs indicating the location of the
accessible load and unload areas shall be provided at entries to
queues and waiting lines.

217 Telephones

217.1 General. Where coin-operated public pay telephones,
coinless public pay telephones, public closed-circuit telephones,
public courtesy phones, or other types of public telephones are
provided, public telephones shall be provided in accordance with 217
for each type of public telephone provided. For purposes of this
section, a bank of telephones shall be considered to be two or more
adjacent telephones.
217.2 Wheelchair Accessible Telephones. Where public telephones
are provided, wheelchair accessible telephones complying with 704.2
shall be provided in accordance with Table 217.2.
EXCEPTION: Drive-up only public telephones shall not be required
to comply with 217.2.

Table 217.2--Wheelchair Accessible Telephones
------------------------------------------------------------------------
Minimum number of required
Number of telephones provided on a floor, wheelchair accessible
level, or exterior site telephones
------------------------------------------------------------------------
1 or more single units.................... 1 per floor, level, and
exterior site.
1 bank.................................... 1 per floor, level, and
exterior site.
2 or more banks........................... 1 per bank.
------------------------------------------------------------------------

217.3 Volume Controls. All public telephones shall have volume
controls complying with 704.3.
217.4 TTYs. TTYs complying with 704.4 shall be provided in
accordance with 217.4.
217.4.1 Bank Requirement. Where four or more public pay
telephones are provided at a bank of telephones, at least one public
TTY complying with 704.4 shall be provided at that bank.
EXCEPTION: TTYs shall not be required at banks of telephones
located within 200 feet (61 m) of, and on the same floor as, a bank
containing a public TTY.
217.4.2 Floor Requirement. TTYs in public buildings shall be
provided in accordance with 217.4.2.1. TTYs in private buildings
shall be provided in accordance with 217.4.2.2.
217.4.2.1 Public Buildings. Where at least one public pay
telephone is provided on a floor of a public building, at least one
public TTY shall be provided on that floor.
217.4.2.2 Private Buildings. Where four or more public pay
telephones are provided on a floor of a private building, at least
one public TTY shall be provided on that floor.
217.4.3 Building Requirement. TTYs in public buildings shall be
provided in accordance with 217.4.3.1. TTYs in private buildings
shall be provided in accordance with 217.4.3.2.
217.4.3.1 Public Buildings. Where at least one public pay
telephone is provided in a public building, at least one public TTY
shall be provided in the building. Where at least one public pay
telephone is provided in a public use area of a public building, at
least one public TTY shall be provided in the public building in a
public use area.
217.4.3.2 Private Buildings. Where four or more public pay
telephones are provided in a private building, at least one public
TTY shall be provided in the building.
217.4.4 Exterior Site Requirement. Where four or more public pay
telephones are provided on an exterior site, at least one public TTY
shall be provided on the site.
217.4.5 Rest Stops, Emergency Roadside Stops, and Service
Plazas. Where at least one public pay telephone is provided at a
public rest stop, emergency roadside stop, or service plaza, at
least one public TTY shall be provided.
217.4.6 Hospitals. Where at least one public pay telephone is
provided serving a hospital emergency room, hospital recovery room,
or hospital waiting room, at least one public TTY shall be provided
at each location.
217.4.7 Transportation Facilities. In transportation facilities,
in addition to the requirements of 217.4.1 through 217.4.4, where at
least one public pay telephone serves a particular entrance to a bus
or rail facility, at least one public TTY shall be provided to serve
that entrance. In airports, in addition to the requirements of
217.4.1 through 217.4.4, where four or more public pay telephones
are located in a terminal outside the security areas, a concourse
within the security areas, or a baggage claim area in a terminal, at
least one public TTY shall be provided in each location.
217.4.8 Detention and Correctional Facilities. In detention and
correctional facilities, where at least one pay telephone is
provided in a secured area used only by detainees or inmates and
security personnel, at least one TTY shall be provided in at least
one secured area.
217.5 Shelves for Portable TTYs. Where a bank of telephones in
the interior of a building consists of three or more public pay
telephones, at least one public pay telephone at the bank shall be
provided with a shelf and an electrical outlet in accordance with
704.5.
EXCEPTIONS: 1. Secured areas of detention and correctional
facilities where shelves and outlets are prohibited for purposes of
security or safety shall not be required to comply with 217.5.
2. The shelf and electrical outlet shall not be required at a
bank of telephones with a TTY.

218 Transportation Facilities

218.1 General. Transportation facilities shall comply with 218.
218.2 New and Altered Fixed Guideway Stations. New and altered
stations in rapid rail, light rail, commuter rail, intercity rail,
high speed rail, and other fixed guideway systems shall comply with
810.5 through 810.10.
218.3 Key Stations and Existing Intercity Rail Stations. Key
stations and existing intercity rail stations shall comply with
810.5 through 810.10.
218.4 Bus Shelters. Where provided, bus shelters shall comply
with 810.3.
218.5 Other Transportation Facilities. In other transportation
facilities, public address systems shall comply with 810.7 and
clocks shall comply with 810.8.

219 Assistive Listening Systems

219.1 General. Assistive listening systems shall be provided in
accordance with 219 and shall comply with 706.
219.2 Required Systems. In each assembly area where audible
communication is integral to the use of the space, an assistive
listening system shall be provided.
EXCEPTION: Other than in courtrooms, assistive listening systems
shall not be required where audio amplification is not provided.
219.3 Receivers. Receivers complying with 706.2 shall be
provided for assistive listening systems in each assembly area in
accordance with Table 219.3. Twenty-five percent minimum of
receivers provided, but no fewer than two, shall be hearing-aid
compatible in accordance with 706.3.
EXCEPTIONS: 1. Where a building contains more than one assembly
area and the assembly areas required to provide assistive listening
systems are under one management, the total number of required
receivers shall be permitted to be calculated according to the total
number of seats in the assembly areas in the building provided that
all receivers are usable with all systems.
2. Where all seats in an assembly area are served by an
induction loop assistive listening system, the minimum number of
receivers required by Table 219.3 to be hearing-aid compatible shall
not be required to be provided.

[[Page 59504]]

Table 219.3--Receivers for Assistive Listening Systems
------------------------------------------------------------------------
Minimum number of
required receivers
Capacity of seating in assembly Minimum number of required to be
area required receivers hearing-aid
compatible
------------------------------------------------------------------------
50 or less...................... 2................. 2.
51 to 200....................... 2, plus 1 per 25 2.
seats over 50
seats.
201 to 500...................... 2, plus 1 per 25 1 per 4
seats over 50 receivers.\1\
seats \1\.
501 to 1000..................... 20, plus 1 per 33 1 per 4
seats over 500 receivers.\1\
seats \1\.
1001 to 2000.................... 35, plus 1 per 50 1 per 4
seats over 1000 receivers.\1\
seats \1\.
2001 and over................... 55 plus 1 per 100 1 per 4
seats over 2000 receivers.\1\
seats \1\.
------------------------------------------------------------------------
\1\ Or fraction thereof.

220 Automatic Teller Machines and Fare Machines

220.1 General. Where automatic teller machines or self-service
fare vending, collection, or adjustment machines are provided, at
least one of each type provided at each location shall comply with
707. Where bins are provided for envelopes, waste paper, or other
purposes, at least one of each type shall comply with 811.

221 Assembly Areas

221.1 General. Assembly areas shall provide wheelchair spaces,
companion seats, and designated aisle seats complying with 221 and
802. In addition, lawn seating shall comply with 221.5.
221.2 Wheelchair Spaces. Wheelchair spaces complying with 221.2
shall be provided in assembly areas with fixed seating.
221.2.1 Number and Location. Wheelchair spaces shall be provided
complying with 221.2.1.
221.2.1.1 General Seating. Wheelchair spaces complying with
802.1 shall be provided in accordance with Table 221.2.1.1.

Table 221.2.1.1--Number of Wheelchair Spaces in Assembly Areas
------------------------------------------------------------------------
Minimum number of required
Number of seats wheelchair spaces
------------------------------------------------------------------------
4 to 25................................... 1.
26 to 50.................................. 2.
51 to 150................................. 4.
151 to 300................................ 5.
301 to 500................................ 6.
501 to 5000............................... 6, plus 1 for each 150, or
fraction thereof, between
501 through 5000.
5001 and over............................. 36, plus 1 for each 200, or
fraction thereof, over
5000.
------------------------------------------------------------------------

221.2.1.2 Luxury Boxes, Club Boxes, and Suites in Arenas,
Stadiums, and Grandstands. In each luxury box, club box, and suite
within arenas, stadiums, and grandstands, wheelchair spaces
complying with 802.1 shall be provided in accordance with Table
221.2.1.1.
221.2.1.3 Other Boxes. In boxes other than those required to
comply with 221.2.1.2, the total number of wheelchair spaces
required shall be determined in accordance with Table 221.2.1.1.
Wheelchair spaces shall be located in not less than 20 percent of
all boxes provided. Wheelchair spaces shall comply with 802.1.
221.2.1.4 Team or Player Seating. At least one wheelchair space
complying with 802.1 shall be provided in team or player seating
areas serving areas of sport activity.
EXCEPTION: Wheelchair spaces shall not be required in team or
player seating areas serving bowling lanes not required to comply
with 206.2.11.
221.2.2 Integration. Wheelchair spaces shall be an integral part
of the seating plan.
221.2.3 Lines of Sight and Dispersion. Wheelchair spaces shall
provide lines of sight complying with 802.2 and shall comply with
221.2.3. In providing lines of sight, wheelchair spaces shall be
dispersed. Wheelchair spaces shall provide spectators with choices
of seating locations and viewing angles that are substantially
equivalent to, or better than, the choices of seating locations and
viewing angles available to all other spectators. When the number of
wheelchair spaces required by 221.2.1 has been met, further
dispersion shall not be required.
EXCEPTION: Wheelchair spaces in team or player seating areas
serving areas of sport activity shall not be required to comply with
221.2.3.
221.2.3.1 Horizontal Dispersion. Wheelchair spaces shall be
dispersed horizontally.
EXCEPTIONS: 1. Horizontal dispersion shall not be required in
assembly areas with 300 or fewer seats if the companion seats
required by 221.3 and wheelchair spaces are located within the 2nd
or 3rd quartile of the total row length. Intermediate aisles shall
be included in determining the total row length. If the row length
in the 2nd and 3rd quartile of a row is insufficient to accommodate
the required number of companion seats and wheelchair spaces, the
additional companion seats and wheelchair spaces shall be permitted
to be located in the 1st and 4th quartile of the row.
2. In row seating, two wheelchair spaces shall be permitted to
be located side-by-side.
221.2.3.2 Vertical Dispersion. Wheelchair spaces shall be
dispersed vertically at varying distances from the screen,
performance area, or playing field. In addition, wheelchair spaces
shall be located in each balcony or mezzanine that is located on an
accessible route.
EXCEPTIONS: 1. Vertical dispersion shall not be required in
assembly areas with 300 or fewer seats if the wheelchair spaces
provide viewing angles that are equivalent to, or better than, the
average viewing angle provided in the facility.
2. In bleachers, wheelchair spaces shall not be required to be
provided in rows other than rows at points of entry to bleacher
seating.
221.3 Companion Seats. At least one companion seat complying
with 802.3 shall be provided for each wheelchair space required by
221.2.1.
221.4 Designated Aisle Seats. At least 5 percent of the total
number of aisle seats provided shall comply with 802.4 and shall be
the aisle seats located closest to accessible routes.
EXCEPTION: Team or player seating areas serving areas of sport
activity shall not be required to comply with 221.4.
221.5 Lawn Seating. Lawn seating areas and exterior overflow
seating areas, where fixed seats are not provided, shall connect to
an accessible route.

222 Dressing, Fitting, and Locker Rooms

222.1 General. Where dressing rooms, fitting rooms, or locker
rooms are provided, at least 5 percent, but no fewer than one, of
each type of use in each cluster provided shall comply with 803.
EXCEPTION: In alterations, where it is technically infeasible to
provide rooms in accordance with 222.1, one room for each sex on
each level shall comply with 803. Where only unisex rooms are
provided, unisex rooms shall be permitted.
222.2 Coat Hooks and Shelves. Where coat hooks or shelves are
provided in dressing, fitting or locker rooms without individual
compartments, at least one of each type shall comply with 803.5.
Where coat hooks or shelves are provided in individual compartments
at least one of each type complying with 803.5 shall be provided in
individual compartments in dressing, fitting, or locker rooms
required to comply with 222.1.

223 Medical Care and Long-Term Care Facilities

223.1 General. In licensed medical care facilities and licensed
long-term care facilities where the period of stay exceeds twenty
four hours, patient or resident sleeping rooms shall be provided in
accordance with 223.
EXCEPTION: Toilet rooms that are part of critical or intensive
care patient sleeping rooms shall not be required to comply with
603.
223.1.1 Alterations. Where sleeping rooms are altered or added,
the requirements of 223 shall apply only to the sleeping rooms being
altered or added until the number of sleeping rooms complies with
the minimum number required for new construction.

[[Page 59505]]

223.2 Hospitals, Rehabilitation Facilities, Psychiatric
Facilities and Detoxification Facilities. Hospitals, rehabilitation
facilities, psychiatric facilities and detoxification facilities
shall comply with 223.2.
223.2.1 Facilities Not Specializing in Treating Conditions That
Affect Mobility. In facilities not specializing in treating
conditions that affect mobility, at least 10 percent, but no fewer
than one, of the patient sleeping rooms shall provide mobility
features complying with 805.
223.2.2 Facilities Specializing in Treating Conditions That
Affect Mobility. In facilities specializing in treating conditions
that affect mobility, 100 percent of the patient sleeping rooms
shall provide mobility features complying with 805.
223.3 Long-Term Care Facilities. In licensed long-term care
facilities, at least 50 percent, but no fewer than one, of each type
of resident sleeping room shall provide mobility features complying
with 805.

224 Transient Lodging Guest Rooms

224.1 General. Transient lodging facilities shall provide guest
rooms in accordance with 224.
224.1.1 Alterations. Where guest rooms are altered or added, the
requirements of 224 shall apply only to the guest rooms being
altered or added until the number of guest rooms complies with the
minimum number required for new construction.
224.1.2 Guest Room Doors and Doorways. Entrances, doors, and
doorways providing user passage into and within guest rooms that are
not required to provide mobility features complying with 806.2 shall
comply with 404.2.3.
EXCEPTION: Shower and sauna doors in guest rooms that are not
required to provide mobility features complying with 806.2 shall not
be required to comply with 404.2.3.
224.2 Guest Rooms with Mobility Features. In transient lodging
facilities, guest rooms with mobility features complying with 806.2
shall be provided in accordance with Table 224.2.

Table 224.2--Guest Rooms With Mobility Features
----------------------------------------------------------------------------------------------------------------
Minimum number of Minimum number of
Total number of guest rooms provided required rooms without required rooms with Total number of
roll-in showers roll-in showers required rooms
----------------------------------------------------------------------------------------------------------------
1 to 25.............................. 1...................... 0...................... 1.
26 to 50............................. 2...................... 0...................... 2.
51 to 75............................. 3...................... 1...................... 4.
76 to 100............................ 4...................... 1...................... 5.
101 to 150........................... 5...................... 2...................... 7.
151 to 200........................... 6...................... 2...................... 8.
201 to 300........................... 7...................... 3...................... 10.
301 to 400........................... 8...................... 4...................... 12.
401 to 500........................... 9...................... 4...................... 13.
501 to 1000.......................... 2 percent of total..... 1 percent of total..... 3 percent of total.
1001 and over........................ 20, plus 1 for each 10, plus 1 for each 30, plus 2 for each
100, or fraction 100, or fraction 100, or fraction
thereof, over 1000. thereof, over 1000. thereof, over 1000.
----------------------------------------------------------------------------------------------------------------

224.3 Beds. In guest rooms having more than 25 beds, 5 percent
minimum of the beds shall have clear floor space complying with
806.2.3.
224.4 Guest Rooms with Communication Features. In transient
lodging facilities, guest rooms with communication features
complying with 806.3 shall be provided in accordance with Table
224.4.

Table 224.4--Guest Rooms With Communication Features
------------------------------------------------------------------------
Minimum number of required
Total number of guest rooms provided guest rooms with
communication features
------------------------------------------------------------------------
2 to 25................................... 2.
26 to 50.................................. 4.
51 to 75.................................. 7.
76 to 100................................. 9.
101 to 150................................ 12.
151 to 200................................ 14.
201 to 300................................ 17.
301 to 400................................ 20.
401 to 500................................ 22.
501 to 1000............................... 5 percent of total.
1001 and over............................. 50, plus 3 for each 100 over
1000.
------------------------------------------------------------------------

224.5 Dispersion. Guest rooms required to provide mobility
features complying with 806.2 and guest rooms required to provide
communication features complying with 806.3 shall be dispersed among
the various classes of guest rooms, and shall provide choices of
types of guest rooms, number of beds, and other amenities comparable
to the choices provided to other guests. Where the minimum number of
guest rooms required to comply with 806 is not sufficient to allow
for complete dispersion, guest rooms shall be dispersed in the
following priority: guest room type, number of beds, and amenities.
At least one guest room required to provide mobility features
complying with 806.2 shall also provide communication features
complying with 806.3. Not more than 10 percent of guest rooms
required to provide mobility features complying with 806.2 shall be
used to satisfy the minimum number of guest rooms required to
provide communication features complying with 806.3.

225 Storage

225.1 General. Storage facilities shall comply with 225.
225.2 Storage. Where storage is provided in accessible spaces,
at least one of each type shall comply with 811.
225.2.1 Lockers. Where lockers are provided, at least 5 percent,
but no fewer than one of each type, shall comply with 811.
225.2.2 Self-Service Shelving. Self-service shelves shall be
located on an accessible route complying with 402. Self-service
shelving shall not be required to comply with 308.
225.3 Self-Service Storage Facilities. Self-service storage
facilities shall provide individual self-service storage spaces
complying with these requirements in accordance with Table 225.3.

Table 225.3--Self-Service Storage Facilities
------------------------------------------------------------------------
Minimum number of spaces
Total spaces in facility required to be accessible
------------------------------------------------------------------------
1 to 200.................................. 5 percent, but no fewer than
1.
201 and over.............................. 10, plus 2 percent of total
number of units over 200.
------------------------------------------------------------------------

225.3.1 Dispersion. Individual self-service storage spaces shall
be dispersed throughout the various classes of spaces provided.
Where more classes of spaces are provided than the number required
to be accessible, the number of spaces shall not be required to
exceed that required by Table 225.3. Self-service storage spaces
complying with Table 225.3 shall not be required to be dispersed
among buildings in a multi-building facility.

226 Dining Surfaces and Work Surfaces

226.1 General. Where dining surfaces are provided for the
consumption of food or drink, at least 5 percent of the seating
spaces and standing spaces at the dining surfaces shall comply with
902. In addition, where work surfaces are provided for use by other
than employees, at least 5 percent shall comply with 902.
EXCEPTIONS: 1. Sales counters and service counters shall not be
required to comply with 902.

[[Page 59506]]

2. Check writing surfaces provided at check-out aisles not
required to comply with 904.3 shall not be required to comply with
902.
226.2 Dispersion. Dining surfaces and work surfaces required to
comply with 902 shall be dispersed throughout the space or facility
containing dining surfaces and work surfaces.

227 Sales and Service

227.1 General. Where provided, check-out aisles, sales counters,
service counters, food service lines, queues, and waiting lines
shall comply with 227 and 904.
227.2 Check-Out Aisles. Where check-out aisles are provided,
check-out aisles complying with 904.3 shall be provided in
accordance with Table 227.2. Where check-out aisles serve different
functions, check-out aisles complying with 904.3 shall be provided
in accordance with Table 227.2 for each function. Where check-out
aisles are dispersed throughout the building or facility, check-out
aisles complying with 904.3 shall be dispersed.
EXCEPTION: Where the selling space is under 5000 square feet
(465 m²) no more than one check-out aisle complying with
904.3 shall be required.

Table 227.2--Check-Out Aisles
------------------------------------------------------------------------
Minimum number of check-out
Number of check-out aisles of each aisles of each function
function required to comply with
904.3
------------------------------------------------------------------------
1 to 4.................................... 1.
5 to 8.................................... 2.
9 to 15................................... 3.
16 and over............................... 3, plus 20 percent of
additional aisles.
------------------------------------------------------------------------

227.2.1 Altered Check-Out Aisles. Where check-out aisles are
altered, at least one of each check-out aisle serving each function
shall comply with 904.3 until the number of check-out aisles
complies with 227.2.
227.3 Counters. Where provided, at least one of each type of
sales counter and service counter shall comply with 904.4. Where
counters are dispersed throughout the building or facility, counters
complying with 904.4 also shall be dispersed.
227.4 Food Service Lines. Food service lines shall comply with
904.5. Where self-service shelves are provided, at least 50 percent,
but no fewer than one, of each type provided shall comply with 308.
227.5 Queues and Waiting Lines. Queues and waiting lines
servicing counters or check-out aisles required to comply with 904.3
or 904.4 shall comply with 403.

228 Depositories, Vending Machines, Change Machines, Mail Boxes, and
Fuel Dispensers

228.1 General. Where provided, at least one of each type of
depository, vending machine, change machine, and fuel dispenser
shall comply with 309.
EXCEPTION: Drive-up only depositories shall not be required to
comply with 309.
228.2 Mail Boxes. Where mail boxes are provided in an interior
location, at least 5 percent, but no fewer than one, of each type
shall comply with 309. In residential facilities, where mail boxes
are provided for each residential dwelling unit, mail boxes
complying with 309 shall be provided for each residential dwelling
unit required to provide mobility features complying with 809.2
through 809.4.

229 Windows

229.1 General. Where glazed openings are provided in accessible
rooms or spaces for operation by occupants, at least one opening
shall comply with 309. Each glazed opening required by an
administrative authority to be operable shall comply with 309.
EXCEPTIONS: 1. Glazed openings in residential dwelling units
required to comply with 809 shall not be required to comply with
229.
2. Glazed openings in guest rooms required to provide
communication features and in guest rooms required to comply with
206.5.3 shall not be required to comply with 229.

230 Two-Way Communication Systems

230.1 General. Where a two-way communication system is provided
to gain admittance to a building or facility or to restricted areas
within a building or facility, the system shall comply with 708.

231 Judicial Facilities

231.1 General. Judicial facilities shall comply with 231.
231.2 Courtrooms. Each courtroom shall comply with 808.
231.3 Holding Cells. Where provided, central holding cells and
court-floor holding cells shall comply with 231.3.
231.3.1 Central Holding Cells. Where separate central holding
cells are provided for adult male, juvenile male, adult female, or
juvenile female, one of each type shall comply with 807.2. Where
central holding cells are provided and are not separated by age or
sex, at least one cell complying with 807.2 shall be provided.
231.3.2 Court-Floor Holding Cells. Where separate court-floor
holding cells are provided for adult male, juvenile male, adult
female, or juvenile female, each courtroom shall be served by one
cell of each type complying with 807.2. Where court-floor holding
cells are provided and are not separated by age or sex, courtrooms
shall be served by at least one cell complying with 807.2. Cells may
serve more than one courtroom.
231.4 Visiting Areas. Visiting areas shall comply with 231.4.
231.4.1 Cubicles and Counters. At least 5 percent, but no fewer
than one, of cubicles shall comply with 902 on both the visitor and
detainee sides. Where counters are provided, at least one shall
comply with 904.4.2 on both the visitor and detainee sides.
EXCEPTION: The detainee side of cubicles or counters at non-
contact visiting areas not serving holding cells required to comply
with 231 shall not be required to comply with 902 or 904.4.2.
231.4.2 Partitions. Where solid partitions or security glazing
separate visitors from detainees at least one of each type of
cubicle or counter partition shall comply with 904.6.

232 Detention Facilities and Correctional Facilities

232.1 General. Buildings, facilities, or portions thereof, in
which people are detained for penal or correction purposes, or in
which the liberty of the inmates is restricted for security reasons
shall comply with 232.
232.2 General Holding Cells and General Housing Cells. General
holding cells and general housing cells shall be provided in
accordance with 232.2.
EXCEPTION: Alterations to cells shall not be required to comply
except to the extent determined by the Attorney General.
232.2.1 Cells with Mobility Features. At least 2 percent, but no
fewer than one, of the total number of cells in a facility shall
provide mobility features complying with 807.2.
232.2.1.1 Beds. In cells having more than 25 beds, at least 5
percent of the beds shall have clear floor space complying with
807.2.3.
232.2.2 Cells with Communication Features. At least 2 percent,
but no fewer than one, of the total number of general holding cells
and general housing cells equipped with audible emergency alarm
systems and permanently installed telephones within the cell shall
provide communication features complying with 807.3.
232.3 Special Holding Cells and Special Housing Cells. Where
special holding cells or special housing cells are provided, at
least one cell serving each purpose shall provide mobility features
complying with 807.2. Cells subject to this requirement include, but
are not limited to, those used for purposes of orientation,
protective custody, administrative or disciplinary detention or
segregation, detoxification, and medical isolation.
EXCEPTION: Alterations to cells shall not be required to comply
except to the extent determined by the Attorney General.
232.4 Medical Care Facilities. Patient bedrooms or cells
required to comply with 223 shall be provided in addition to any
medical isolation cells required to comply with 232.3.
232.5 Visiting Areas. Visiting areas shall comply with 232.5.
232.5.1 Cubicles and Counters. At least 5 percent, but no fewer
than one, of cubicles shall comply with 902 on both the visitor and
detainee sides. Where counters are provided, at least one shall
comply with 904.4.2 on both the visitor and detainee or inmate
sides.
EXCEPTION: The inmate or detainee side of cubicles or counters
at non-contact visiting areas not serving holding cells or housing
cells required to comply with 232 shall not be required to comply
with 902 or 904.4.2.
232.5.2 Partitions. Where solid partitions or security glazing
separate visitors from detainees or inmates at least one of each
type of cubicle or counter partition shall comply with 904.6.

233 Residential Facilities

233.1 General. Facilities with residential dwelling units shall
comply with 233.
233.2 Residential Dwelling Units Provided by Entities Subject to
HUD Section

[[Page 59507]]

504 Regulations. Where facilities with residential dwelling units
are provided by entities subject to regulations issued by the
Department of Housing and Urban Development (residential dwelling
units with mobility features complying with 809.2 through 809.4 in a
number required by the applicable HUD regulations. Residential
dwelling units required to provide mobility features complying with
809.2 through 809.4 shall be on an accessible route as required by
206. In addition, such entities shall provide residential dwelling
units with communication features complying with 809.5 in a number
required by the applicable HUD regulations. Entities subject to
233.2 shall not be required to comply with 233.3.
233.3 Residential Dwelling Units Provided by Entities Not
Subject to HUD Section 504 Regulations. Facilities with residential
dwelling units provided by entities not subject to regulations
issued by the Department of Housing and Urban Development (HUD)
under Section 504 of the Rehabilitation Act of 1973, as amended,
shall comply with 233.3.
233.3.1 Minimum Number: New Construction. Newly constructed
facilities with residential dwelling units shall comply with
233.3.1.
EXCEPTION: Where facilities contain 15 or fewer residential
dwelling units, the requirements of 233.3.1.1 and 233.3.1.2 shall
apply to the total number of residential dwelling units that are
constructed under a single contract, or are developed as a whole,
whether or not located on a common site.
233.3.1.1 Residential Dwelling Units with Mobility Features. In
facilities with residential dwelling units, at least 5 percent, but
no fewer than one unit, of the total number of residential dwelling
units shall provide mobility features complying with 809.2 through
809.4 and shall be on an accessible route as required by 206.
233.3.1.2 Residential Dwelling Units with Communication
Features. In facilities with residential dwelling units, at least 2
percent, but no fewer than one unit, of the total number of
residential dwelling units shall provide communication features
complying with 809.5.
233.3.2 Residential Dwelling Units for Sale. Residential
dwelling units offered for sale shall provide accessible features to
the extent required by regulations issued by Federal agencies under
the Americans with Disabilities Act or Section 504 of the
Rehabilitation Act of 1973, as amended.
233.3.3 Additions. Where an addition to an existing building
results in an increase in the number of residential dwelling units,
the requirements of 233.3.1 shall apply only to the residential
dwelling units that are added until the total number of residential
dwelling units complies with the minimum number required by 233.3.1.
Residential dwelling units required to comply with 233.3.1.1 shall
be on an accessible route as required by 206.
233.3.4 Alterations. Alterations shall comply with 233.3.4.
EXCEPTION: Where compliance with 809.2, 809.3, or 809.4 is
technically infeasible, or where it is technically infeasible to
provide an accessible route to a residential dwelling unit, the
entity shall be permitted to alter or construct a comparable
residential dwelling unit to comply with 809.2 through 809.4
provided that the minimum number of residential dwelling units
required by 233.3.1.1 and 233.3.1.2, as applicable, is satisfied.
233.3.4.1 Alterations to Vacated Buildings. Where a building is
vacated for the purposes of alteration, and the altered building
contains more than 15 residential dwelling units, at least 5 percent
of the residential dwelling units shall comply with 809.2 through
809.4 and shall be on an accessible route as required by 206. In
addition, at least 2 percent of the residential dwelling units shall
comply with 809.5.
233.3.4.2 Alterations to Individual Residential Dwelling Units.
In individual residential dwelling units, where a bathroom or a
kitchen is substantially altered, and at least one other room is
altered, the requirements of 233.3.1 shall apply to the altered
residential dwelling units until the total number of residential
dwelling units complies with the minimum number required by
233.3.1.1 and 233.3.1.2. Residential dwelling units required to
comply with 233.3.1.1 shall be on an accessible route as required by
206.
EXCEPTION: Where facilities contain 15 or fewer residential
dwelling units, the requirements of 233.3.1.1 and 233.3.1.2 shall
apply to the total number of residential dwelling units that are
altered under a single contract, or are developed as a whole,
whether or not located on a common site.
233.3.5 Dispersion. Residential dwelling units required to
provide mobility features complying with 809.2 through 809.4 and
residential dwelling units required to provide communication
features complying with 809.5 shall be dispersed among the various
types of residential dwelling units in the facility and shall
provide choices of residential dwelling units comparable to, and
integrated with, those available to other residents.
EXCEPTION: Where multi-story residential dwelling units are one
of the types of residential dwelling units provided, one-story
residential dwelling units shall be permitted as a substitute for
multi-story residential dwelling units where equivalent spaces and
amenities are provided in the one-story residential dwelling unit.

234 Amusement Rides

234.1 General. Amusement rides shall comply with 234.
EXCEPTION: Mobile or portable amusement rides shall not be
required to comply with 234.
234.2 Load and Unload Areas. Load and unload areas serving
amusement rides shall comply with 1002.3.
234.3 Minimum Number. Amusement rides shall provide at least one
wheelchair space complying with 1002.4, or at least one amusement
ride seat designed for transfer complying with 1002.5, or at least
one transfer device complying with 1002.6.
EXCEPTIONS: 1. Amusement rides that are controlled or operated
by the rider shall not be required to comply with 234.3.
2. Amusement rides designed primarily for children, where
children are assisted on and off the ride by an adult, shall not be
required to comply with 234.3.
3. Amusement rides that do not provide amusement ride seats
shall not be required to comply with 234.3.
234.4 Existing Amusement Rides. Where existing amusement rides
are altered, the alteration shall comply with 234.4.
234.4.1 Load and Unload Areas. Where load and unload areas
serving existing amusement rides are newly designed and constructed,
the load and unload areas shall comply with 1002.3.
234.4.2 Minimum Number. Where the structural or operational
characteristics of an amusement ride are altered to the extent that
the amusement ride's performance differs from that specified by the
manufacturer or the original design, the amusement ride shall comply
with 234.3.

235 Recreational Boating Facilities

235.1 General. Recreational boating facilities shall comply with
235.
235.2 Boat Slips. Boat slips complying with 1003.3.1 shall be
provided in accordance with Table 235.2. Where the number of boat
slips is not identified, each 40 feet (12 m) of boat slip edge
provided along the perimeter of the pier shall be counted as one
boat slip for the purpose of this section.

Table 235.2--Boat Slips
------------------------------------------------------------------------
Total number of boat slips provided in Minimum number of required
facility accessible boat slips
------------------------------------------------------------------------
1 to 25................................... 1.
26 to 50.................................. 2.
51 to 100................................. 3.
101 to 150................................ 4.
151 to 300................................ 5.
301 to 400................................ 6.
401 to 500................................ 7.
501 to 600................................ 8.
601 to 700................................ 9.
701 to 800................................ 10.
801 to 900................................ 11.
901 to 1000............................... 12.
1001 and over............................. 12, plus 1 for every 100, or
fraction thereof, over 1000.
------------------------------------------------------------------------

235.2.1 Dispersion. Boat slips complying with 1003.3.1 shall be
dispersed throughout the various types of boat slips provided. Where
the minimum number of boat slips required to comply with 1003.3.1
has been met, no further dispersion shall be required.
235.3 Boarding Piers at Boat Launch Ramps. Where boarding piers
are provided at boat launch ramps, at least 5 percent, but no fewer
than one, of the boarding piers shall comply with 1003.3.2.

236 Exercise Machines and Equipment

236.1 General. At least one of each type of exercise machine and
equipment shall comply with 1004.

237 Fishing Piers and Platforms

237.1 General. Fishing piers and platforms shall comply with
1005.

[[Page 59508]]

238 Golf Facilities

238.1 General. Golf facilities shall comply with 238.
238.2 Golf Courses. Golf courses shall comply with 238.2.
238.2.1 Teeing Grounds. Where one teeing ground is provided for
a hole, the teeing ground shall be designed and constructed so that
a golf car can enter and exit the teeing ground. Where two teeing
grounds are provided for a hole, the forward teeing ground shall be
designed and constructed so that a golf car can enter and exit the
teeing ground. Where three or more teeing grounds are provided for a
hole, at least two teeing grounds, including the forward teeing
ground, shall be designed and constructed so that a golf car can
enter and exit each teeing ground.
EXCEPTION: In existing golf courses, the forward teeing ground
shall not be required to be one of the teeing grounds on a hole
designed and constructed so that a golf car can enter and exit the
teeing ground where compliance is not feasible due to terrain.
238.2.2 Putting Greens. Putting greens shall be designed and
constructed so that a golf car can enter and exit the putting green.
238.2.3 Weather Shelters. Where provided, weather shelters shall
be designed and constructed so that a golf car can enter and exit
the weather shelter and shall comply with 1006.4.
238.3 Practice Putting Greens, Practice Teeing Grounds, and
Teeing Stations at Driving Ranges. At least 5 percent, but no fewer
than one, of practice putting greens, practice teeing grounds, and
teeing stations at driving ranges shall be designed and constructed
so that a golf car can enter and exit the practice putting greens,
practice teeing grounds, and teeing stations at driving ranges.

239 Miniature Golf Facilities

239.1 General. Miniature golf facilities shall comply with 239.
239.2 Minimum Number. At least 50 percent of holes on miniature
golf courses shall comply with 1007.3.
239.3 Miniature Golf Course Configuration. Miniature golf
courses shall be configured so that the holes complying with 1007.3
are consecutive. Miniature golf courses shall provide an accessible
route from the last hole complying with 1007.3 to the course
entrance or exit without requiring travel through any other holes on
the course.
EXCEPTION: One break in the sequence of consecutive holes shall
be permitted provided that the last hole on the miniature golf
course is the last hole in the sequence.

240 Play Areas

240.1 General. Play areas for children ages 2 and over shall
comply with 240. Where separate play areas are provided within a
site for specific age groups, each play area shall comply with 240.
EXCEPTIONS: 1. Play areas located in family child care
facilities where the proprietor actually resides shall not be
required to comply with 240.
2. In existing play areas, where play components are relocated
for the purposes of creating safe use zones and the ground surface
is not altered or extended for more than one use zone, the play area
shall not be required to comply with 240.
3. Amusement attractions shall not be required to comply with
240.
4. Where play components are altered and the ground surface is
not altered, the ground surface shall not be required to comply with
1008.2.6 unless required by 202.4.
240.1.1 Additions. Where play areas are designed and constructed
in phases, the requirements of 240 shall apply to each successive
addition so that when the addition is completed, the entire play
area complies with all the applicable requirements of 240.
240.2 Play Components. Where provided, play components shall
comply with 240.2.
240.2.1 Ground Level Play Components. Ground level play
components shall be provided in the number and types required by
240.2.1. Ground level play components that are provided to comply
with 240.2.1.1 shall be permitted to satisfy the additional number
required by 240.2.1.2 if the minimum required types of play
components are satisfied. Where two or more required ground level
play components are provided, they shall be dispersed throughout the
play area and integrated with other play components.
240.2.1.1 Minimum Number and Types. Where ground level play
components are provided, at least one of each type shall be on an
accessible route and shall comply with 1008.4.
240.2.1.2 Additional Number and Types. Where elevated play
components are provided, ground level play components shall be
provided in accordance with Table 240.2.1.2 and shall comply with
1008.4.
EXCEPTION: If at least 50 percent of the elevated play
components are connected by a ramp and at least 3 of the elevated
play components connected by the ramp are different types of play
components, the play area shall not be required to comply with
240.2.1.2.

Table 240.2.1.2--Number and Types of Ground Level Play Components
Required To Be on Accessible Routes
------------------------------------------------------------------------
Minimum number of
Minimum number of different types of
ground level play ground level play
Number of elevated play components components
components provided required to be on required to be on
an accessible an accessible
route route
------------------------------------------------------------------------
1............................... Not applicable.... Not applicable.
2 to 4.......................... 1................. 1.
5 to 7.......................... 2................. 2.
8 to 10......................... 3................. 3.
11 to 13........................ 4................. 3.
14 to 16........................ 5................. 3.
17 to 19........................ 6................. 3.
20 to 22........................ 7................. 4.
23 to 25........................ 8................. 4.
26 and over..................... 8, plus 1 for each 5.
additional 3, or
fraction thereof,
over 25.
------------------------------------------------------------------------

240.2.2 Elevated Play Components. Where elevated play components
are provided, at least 50 percent shall be on an accessible route
and shall comply with 1008.4.

241 Saunas and Steam Rooms

241.1 General. Where provided, saunas and steam rooms shall
comply with 612.
EXCEPTION: Where saunas or steam rooms are clustered at a single
location, no more than 5 percent of the saunas and steam rooms, but
no fewer than one, of each type in each cluster shall be required to
comply with 612.

242 Swimming Pools, Wading Pools, and Spas

242.1 General. Swimming pools, wading pools, and spas shall
comply with 242.
242.2 Swimming Pools. At least two accessible means of entry
shall be provided for swimming pools. Accessible means of entry
shall be swimming pool lifts complying with 1009.2; sloped entries
complying with 1009.3; transfer walls complying with 1009.4;
transfer systems complying with 1009.5; and pool stairs complying
with 1009.6. At least one accessible means of entry provided shall
comply with 1009.2 or 1009.3.
EXCEPTIONS: 1. Where a swimming pool has less than 300 linear
feet (91 m) of swimming pool wall, no more than one accessible means
of entry shall be required provided that the accessible means of
entry is a swimming pool lift complying with 1009.2 or sloped entry
complying with 1009.3.

[[Page 59509]]

2. Wave action pools, leisure rivers, sand bottom pools, and
other pools where user access is limited to one area shall not be
required to provide more than one accessible means of entry provided
that the accessible means of entry is a swimming pool lift complying
with 1009.2, a sloped entry complying with 1009.3, or a transfer
system complying with 1009.5.
3. Catch pools shall not be required to provide an accessible
means of entry provided that the catch pool edge is on an accessible
route.
242.3 Wading Pools. At least one accessible means of entry shall
be provided for wading pools. Accessible means of entry shall comply
with sloped entries complying with 1009.3.
242.4 Spas. At least one accessible means of entry shall be
provided for spas. Accessible means of entry shall comply with
swimming pool lifts complying with 1009.2; transfer walls complying
with 1009.4; or transfer systems complying with 1009.5.
EXCEPTION: Where spas are provided in a cluster, no more than 5
percent, but no fewer than one, spa in each cluster shall be
required to comply with 242.4.

243 Shooting Facilities With Firing Positions

243.1 General. Where shooting facilities with firing positions
are designed and constructed at a site, at least 5 percent, but no
fewer than one, of each type of firing position shall comply with
1010.

0
6. Revise Appendix C to this part to read as follows:

Appendix C to Part 1191--Architectural Barriers Act: Scoping

ABA Chapter 1: Application and Administration

F101 Purpose

F101.1 General. This document contains scoping and technical
requirements for accessibility to sites, facilities, buildings, and
elements by individuals with disabilities. The requirements are to
be applied during the design, construction, addition to, alteration,
and lease of sites, facilities, buildings, and elements to the
extent required by regulations issued by Federal agencies under the
Architectural Barriers Act of 1968 (ABA).

F102 Dimensions for Adults and Children

F102.1 General. The technical requirements are based on adult
dimensions and anthropometrics. In addition, this document includes
technical requirements based on children's dimensions and
anthropometrics for drinking fountains, water closets, toilet
compartments, lavatories and sinks, dining surfaces, and work
surfaces.

F103 Modifications and Waivers

F103.1 General. The Architectural Barriers Act authorizes the
Administrator of the General Services Administration, the Secretary
of the Department of Housing and Urban Development, the Secretary of
the Department of Defense, and the United States Postal Service to
modify or waive the accessibility standards for buildings and
facilities covered by the Architectural Barriers Act on a case-by-
case basis, upon application made by the head of the department,
agency, or instrumentality of the United States concerned. The
General Services Administration, the Department of Housing and Urban
Development, the Department of Defense, and the United States Postal
Service may grant a modification or waiver only upon a determination
that it is clearly necessary. Section 502(b)(1) of the
Rehabilitation Act of 1973 authorizes the Access Board to ensure
that modifications and waivers are based on findings of fact and are
not inconsistent with the Architectural Barriers Act.

F104 Conventions

F104.1 Dimensions. Dimensions that are not stated as ``maximum''
or ``minimum'' are absolute.
F104.1.1 Construction and Manufacturing Tolerances. All
dimensions are subject to conventional industry tolerances except
where the requirement is stated as a range with specific minimum and
maximum end points.
F104.2 Calculation of Percentages. Where the required number of
elements or facilities to be provided is determined by calculations
of ratios or percentages and remainders or fractions result, the
next greater whole number of such elements or facilities shall be
provided. Where the determination of the required size or dimension
of an element or facility involves ratios or percentages, rounding
down for values less than one half shall be permitted.
F104.3 Figures. Unless specifically stated otherwise, figures
are provided for informational purposes only.

F105 Referenced Standards

F105.1 General. The standards listed in F105.2 are incorporated
by reference in this document and are part of the requirements to
the prescribed extent of each such reference. The Director of the
Federal Register has approved these standards for incorporation by
reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51.
Copies of the referenced standards may be inspected at the
Architectural and Transportation Barriers Compliance Board, 1331 F
Street NW., Suite 1000, Washington, DC 20004; at the Department of
Justice, Civil Rights Division, Disability Rights Section, 1425 New
York Avenue NW., Washington, DC 20005; at the Department of
Transportation, 1200 New Jersey Avenue SE., Washington, DC 20590; or
at the National Archives and Records Administration (NARA). For
information on the availability of this material at NARA, call (202)
741-6030, or go to https://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
F105.2 Referenced Standards. The specific edition of the
standards listed below are referenced in this document. Where
differences occur between this document and the referenced
standards, this document applies.
F105.2.1 ANSI/BHMA. Copies of the referenced standards may be
obtained from the Builders Hardware Manufacturers Association, 355
Lexington Avenue, 15th floor, New York, NY 10017 (https://www.buildershardware.com).
ANSI/BHMA A156.10-1999 American National Standard for Power
Operated Pedestrian Doors (see 404.3).
ANSI/BHMA A156.19-1997 American National Standard for Power
Assist and Low Energy Power Operated Doors (see 404.3, 408.3.2.1,
and 409.3.1).
ANSI/BHMA A156.19-2002 American National Standard for Power
Assist and Low Energy Power Operated Doors (see 404.3, 408.3.2.1,
and 409.3.1).
F105.2.2 ASME. Copies of the referenced standards may be
obtained from the American Society of Mechanical Engineers, Two Park
Avenue, New York, New York 10016 (https://www.asme.org).
ASME A17.1-2000 Safety Code for Elevators and Escalators,
including ASME A17.1a-2002 Addenda and ASME A17.1b-2003 Addenda (see
407.1, 408.1, 409.1, and 810.9).
ASME A18.1-1999 Safety Standard for Platform Lifts and Stairway
Chairlifts, including ASME A18.1a 2001 Addenda and ASME A18.1b-2001
Addenda (see 410.1).
ASME A18.1-2003 Safety Standard for Platform Lifts and Stairway
Chairlifts, (see 410.1).
F105.2.3 ASTM. Copies of the referenced standards may be
obtained from the American Society for Testing and Materials, 100
Bar Harbor Drive, West Conshohocken, Pennsylvania 19428 (https://www.astm.org).
ASTM F1292-99 Standard Specification for Impact Attenuation of
Surface Systems Under and Around Playground Equipment (see
1008.2.6.2).
ASTM F1292-04 Standard Specification for Impact Attenuation of
Surfacing Materials Within the Use Zone of Playground Equipment (see
1008.2.6.2).
ASTM F1487-01 Standard Consumer Safety Performance Specification
for Playground Equipment for Public Use (see F106.5).
ASTM F1951-99 Standard Specification for Determination of
Accessibility of Surface Systems Under and Around Playground
Equipment (see 1008.2.6.1).
F105.2.4 ICC/IBC. Copies of the referenced standard may be
obtained from the International Code Council, 500 New Jersey Avenue
NW., Washington, DC 20001 (www.iccsafe.org).
International Building Code, 2000 Edition (see F207.1, F207.2,
F216.4.2, F216.4.3, and 1005.2.1).
International Building Code, 2001 Supplement (see F207.1 and
F207.2).
International Building Code, 2003 Edition (see F207.1, F207.2,
F216.4.2, F216.4.3, and 1005.2.1).
F105.2.5 NFPA. Copies of the referenced standards may be
obtained from the National Fire Protection Association, 1
Batterymarch Park, Quincy, Massachusetts 02169 (https://www.nfpa.org).
NFPA 72 National Fire Alarm Code, 1999 Edition (see 702.1 and
809.5.2).
NFPA 72 National Fire Alarm Code, 2002 Edition (see 702.1 and
809.5.2).

[[Page 59510]]

F106 Definitions

F106.1 General. For the purpose of this document, the terms
defined in F106.5 have the indicated meaning.
F106.2 Terms Defined in Referenced Standard. Terms not defined
in F106.5 or in regulations issued by the Administrator of the
General Services Administration, the Secretary of Defense, the
Secretary of Housing and Urban Development, or the United States
Postal Service to implement the Architectural Barriers Act but
specifically defined in a referenced standard, shall have the
specified meaning from the referenced standard unless otherwise
stated.
F106.3 Undefined Terms. The meaning of terms not specifically
defined in F106.5 or in regulations issued by the Administrator of
the General Services Administration, the Secretary of Defense, the
Secretary of Housing and Urban Development, or the United States
Postal Service to implement the Architectural Barriers Act or in
referenced standards shall be as defined by collegiate dictionaries
in the sense that the context implies.
F106.4 Interchangeability. Words, terms and phrases used in the
singular include the plural and those used in the plural include the
singular.
F106.5 Defined Terms.
Accessible. A site, building, facility, or portion thereof that
complies with this part.
Accessible Means of Egress. A continuous and unobstructed way of
egress travel from any point in a building or facility that provides
an accessible route to an area of refuge, a horizontal exit, or a
public way.
Addition. An expansion, extension, or increase in the gross
floor area or height of a building or facility.
Administrative Authority. A governmental agency that adopts or
enforces regulations and guidelines for the design, construction, or
alteration of buildings and facilities.
Alteration. A change to a building or facility that affects or
could affect the usability of the building or facility or portion
thereof. Alterations include, but are not limited to, remodeling,
renovation, rehabilitation, reconstruction, historic restoration,
resurfacing of circulation paths or vehicular ways, changes or
rearrangement of the structural parts or elements, and changes or
rearrangement in the plan configuration of walls and full-height
partitions. Normal maintenance, reroofing, painting or wallpapering,
or changes to mechanical and electrical systems are not alterations
unless they affect the usability of the building or facility.
Amusement Attraction. Any facility, or portion of a facility,
located within an amusement park or theme park which provides
amusement without the use of an amusement device. Amusement
attractions include, but are not limited to, fun houses, barrels,
and other attractions without seats.
Amusement Ride. A system that moves persons through a fixed
course within a defined area for the purpose of amusement.
Amusement Ride Seat. A seat that is built-in or mechanically
fastened to an amusement ride intended to be occupied by one or more
passengers.
Area of Sport Activity. That portion of a room or space where
the play or practice of a sport occurs.
Assembly Area. A building or facility, or portion thereof, used
for the purpose of entertainment, worship, educational or civic
gatherings, or similar purposes. For the purposes of these
requirements, assembly areas include, but are not limited to,
classrooms, lecture halls, courtrooms, public meeting rooms, public
hearing rooms, legislative chambers, motion picture houses,
auditoria, theaters, playhouses, dinner theaters, concert halls,
centers for the performing arts, amphitheaters, arenas, stadiums,
grandstands, or convention centers.
Assistive Listening System (ALS). An amplification system
utilizing transmitters, receivers, and coupling devices to bypass
the acoustical space between a sound source and a listener by means
of induction loop, radio frequency, infrared, or direct-wired
equipment.
Boarding Pier. A portion of a pier where a boat is temporarily
secured for the purpose of embarking or disembarking.
Boards. Boards include, but are not limited to, wood, plastic,
metal, and composite products.
Boat Launch Ramp. A sloped surface designed for launching and
retrieving trailered boats and other water craft to and from a body
of water.
Boat Slip. That portion of a pier, main pier, finger pier, or
float where a boat is moored for the purpose of berthing, embarking,
or disembarking.
Building. Any structure used or intended for supporting or
sheltering any use or occupancy.
Camp Shelter. A partially enclosed structure that provides
campers and hikers cover from weather and that does not contain
plumbing fixtures or kitchen appliances. Camp shelters are not
transient lodging facilities or residential dwelling units.
Camping Facility. A site, or portion of a site, developed for
outdoor recreational purposes that contains camping units.
Camping Unit. An outdoor space in a camping facility used for
camping that contains outdoor constructed features, parking spaces
for recreational vehicles or other vehicles, tent pads or tent
platforms, or camp shelters.
Catch Pool. A pool or designated section of a pool used as a
terminus for water slide flumes.
Characters. Letters, numbers, punctuation marks and typographic
symbols.
Children's Use. Describes spaces and elements specifically
designed for use primarily by people 12 years old and younger.
Circulation Path. An exterior or interior way of passage
provided for pedestrian travel, including but not limited to, walks,
hallways, courtyards, elevators, platform lifts, ramps, stairways,
and landings.
Closed-Circuit Telephone. A telephone with a dedicated line such
as a house phone, courtesy phone or phone that must be used to gain
entry to a facility.
Common Use. Interior or exterior circulation paths, rooms,
spaces, or elements that are not for public use and are made
available for the shared use of two or more people.
Cross Slope. The slope that is perpendicular to the direction of
travel (see running slope).
Curb Ramp. A short ramp cutting through a curb or built up to
it.
Detectable Warning. A standardized surface feature built in or
applied to walking surfaces or other elements to warn of hazards on
a circulation path.
Element. An architectural or mechanical component of a building,
facility, space, or site.
Elevated Play Component. A play component that is approached
above or below grade and that is part of a composite play structure
consisting of two or more play components attached or functionally
linked to create an integrated unit providing more than one play
activity.
Employee Work Area. All or any portion of a space used only by
employees and used only for work. Corridors, toilet rooms,
kitchenettes and break rooms are not employee work areas.
Entrance. Any access point to a building or portion of a
building or facility used for the purpose of entering. An entrance
includes the approach walk, the vertical access leading to the
entrance platform, the entrance platform itself, vestibule if
provided, the entry door or gate, and the hardware of the entry door
or gate.
Facility. All or any portion of buildings, structures, site
improvements, elements, and pedestrian routes or vehicular ways
located on a site.
Gangway. A variable-sloped pedestrian walkway that links a fixed
structure or land with a floating structure. Gangways that connect
to vessels are not addressed by this document.
Golf Car Passage. A continuous passage on which a motorized golf
car can operate.
Ground Level Play Component. A play component that is approached
and exited at the ground level.
Joint Use. Interior or exterior rooms, spaces, or elements that
are common space available for use by all occupants of the building.
Joint use does not include mechanical or custodial rooms, or areas
occupied by other tenants.
Lease. Any agreement which establishes the relationship of
landlord and tenant.
Mail Boxes. Receptacles for the receipt of documents, packages,
or other deliverable matter. Mail boxes include, but are not limited
to, post office boxes and receptacles provided by commercial mail-
receiving agencies, apartment facilities, or schools.
Marked Crossing. A crosswalk or other identified path intended
for pedestrian use in crossing a vehicular way.
Mezzanine. An intermediate level or levels between the floor and
ceiling of any story with an aggregate floor area of not more than
one-third of the area of the room or space in which the level or
levels are located. Mezzanines have sufficient elevation that space
for human occupancy can be provided on the floor below.
Military Installation. A base, camp, post, station, yard,
center, homeport facility for

[[Page 59511]]

any ship, or other activity or operation under the jurisdiction of
the Department of Defense, including any leased facility. Military
installation does not include any facility used primarily for civil
works, rivers and harbors projects, or flood control projects.
Multiple, contiguous, or collocated bases, camps, posts, stations,
yards, centers, or home ports shall not be considered as
constituting a single military installation.
Occupant Load. The number of persons for which the means of
egress of a building or portion of a building is designed.
Operable Part. A component of an element used to insert or
withdraw objects, or to activate, deactivate, or adjust the element.
Outdoor Constructed Features. Picnic tables, fire rings, grills,
fireplaces, wood stoves, trash and recycling receptacles, water
hydrants, utility and sewage hookups, outdoor rinsing showers,
benches, and viewing scopes provided at outdoor recreation
facilities.
Picnic Facility. A site, or portion of a site, developed for
outdoor recreational purposes that contains picnic units.
Picnic Unit. An outdoor space in a picnic facility used for
picnicking that contains outdoor constructed features.
Pictogram. A pictorial symbol that represents activities,
facilities, or concepts.
Play Area. A portion of a site containing play components
designed and constructed for children.
Play Component. An element intended to generate specific
opportunities for play, socialization, or learning. Play components
are manufactured or natural; and are stand-alone or part of a
composite play structure.
Public Entrance. An entrance that is not a service entrance or a
restricted entrance.
Public Use. Interior or exterior rooms, spaces, or elements that
are made available to the public. Public use may be provided at a
building or facility that is privately or publicly owned.
Public Way. Any street, alley or other parcel of land open to
the outside air leading to a public street, which has been deeded,
dedicated or otherwise permanently appropriated to the public for
public use, and which has a clear width and height of not less than
10 feet (3050 mm).
Qualified Historic Building or Facility. A building or facility
that is listed in or eligible for listing in the National Register
of Historic Places, or designated as historic under an appropriate
State or local law.
Ramp. A walking surface that has a running slope steeper than
1:20.
Residential Dwelling Unit. A unit intended to be used as a
residence, that is primarily long-term in nature. Residential
dwelling units do not include transient lodging, inpatient medical
care, licensed long-term care, and detention or correctional
facilities.
Restricted Entrance. An entrance that is made available for
common use on a controlled basis but not public use and that is not
a service entrance.
Running Slope. The slope that is parallel to the direction of
travel (see cross slope).
Self-Service Storage. Building or facility designed and used for
the purpose of renting or leasing individual storage spaces to
customers for the purpose of storing and removing personal property
on a self-service basis.
Service Entrance. An entrance intended primarily for delivery of
goods or services.
Site. A parcel of land bounded by a property line or a
designated portion of a public right-of-way.
Soft Contained Play Structure. A play structure made up of one
or more play components where the user enters a fully enclosed play
environment that utilizes pliable materials, such as plastic,
netting, or fabric.
Space. A definable area, such as a room, toilet room, hall,
assembly area, entrance, storage room, alcove, courtyard, or lobby.
Story. That portion of a building or facility designed for human
occupancy included between the upper surface of a floor and upper
surface of the floor or roof next above. A story containing one or
more mezzanines has more than one floor level.
Structural Frame. The columns and the girders, beams, and
trusses having direct connections to the columns and all other
members that are essential to the stability of the building or
facility as a whole.
Tactile. An object that can be perceived using the sense of
touch.
Technically Infeasible. With respect to an alteration of a
building or a facility, something that has little likelihood of
being accomplished because existing structural conditions would
require removing or altering a loadbearing member that is an
essential part of the structural frame; or because other existing
physical or site constraints prohibit modification or addition of
elements, spaces, or features that are in full and strict compliance
with the minimum requirements.
Teeing Ground. In golf, the starting place for the hole to be
played.
Trail. A pedestrian route developed primarily for outdoor
recreational purposes. A pedestrian route developed primarily to
connect elements, spaces, or facilities within a site is not a
trail.
Trailhead. An outdoor space that is designated by an entity
responsible for administering or maintaining a trail to serve as an
access point to the trail. The junction of two or more trails or the
undeveloped junction of a trail and a road is not a trailhead.
Transfer Device. Equipment designed to facilitate the transfer
of a person from a wheelchair or other mobility aid to and from an
amusement ride seat.
Transient Lodging. A building or facility containing one or more
guest room(s) for sleeping that provides accommodations that are
primarily short-term in nature. Transient lodging does not include
residential dwelling units intended to be used as a residence,
inpatient medical care facilities, licensed long-term care
facilities, detention or correctional facilities, or private
buildings or facilities that contain not more than five rooms for
rent or hire and that are actually occupied by the proprietor as the
residence of such proprietor.
Transition Plate. A sloping pedestrian walking surface located
at the end(s) of a gangway.
TTY. An abbreviation for teletypewriter. Machinery that employs
interactive text-based communication through the transmission of
coded signals across the telephone network. TTYs may include, for
example, devices known as TDDs (telecommunication display devices or
telecommunication devices for deaf persons) or computers with
special modems. TTYs are also called text telephones.
Use Zone. The ground level area beneath and immediately adjacent
to a play structure or play equipment that is designated by ASTM F
1487 (incorporated by reference, see ``Referenced Standards'' in
Chapter 1) for unrestricted circulation around the play equipment
and where it is predicted that a user would land when falling from
or exiting the play equipment.
Vehicular Way. A route provided for vehicular traffic, such as
in a street, driveway, or parking facility.
Viewing Area. An outdoor space developed for viewing landscapes,
wildlife, or other points of interest.
Walk. An exterior prepared surface for pedestrian use, including
pedestrian areas such as plazas and courts.
Wheelchair Space. Space for a single wheelchair and its
occupant.
Work Area Equipment. Any machine, instrument, engine, motor,
pump, conveyor, or other apparatus used to perform work. As used in
this document, this term shall apply only to equipment that is
permanently installed or built-in in employee work areas subject to
the Americans with Disabilities Act of 1990 (ADA). Work area
equipment does not include passenger elevators and other accessible
means of vertical transportation.

ABA CHAPTER 2: SCOPING REQUIREMENTS

F201 Application

F201.1 Scope. All areas of newly designed and newly constructed
buildings and facilities and altered or leased portions of existing
buildings and facilities shall comply with these requirements.
F201.2 Application Based on Building or Facility Use. Where a
site, building, facility, room, or space contains more than one use,
each portion shall comply with the applicable requirements for that
use.
F201.3 Temporary and Permanent Structures. These requirements
shall apply to temporary and permanent buildings and facilities.
F201.4 Requirements Apply to Facilities Constructed or Altered
by or on Behalf of Federal Agencies. The requirements in F216.13,
F244 through F248, and 1011 through 1019 shall apply only to
facilities constructed or altered by federal agencies or by non-
federal entities on federal land on behalf of federal agencies
pursuant to a concession contract, partnership agreement, or similar
arrangement.
F201.4.1 Documentation and Notification When Exceptions Used for
Trails and Beach Access Routes. Federal agencies shall document the
basis for not fully complying with a specific provision in 1017 or
1018 on a portion of a trail or beach access route based on
Exception 1 in 1017 or Exception 1 in 1018, and shall maintain the
documentation with the records for the trail

[[Page 59512]]

or beach project. Federal agencies shall notify the Access Board if
an entire trail is exempted from complying with 1017 based on
Exception 2 in 1017.1, and if a beach access route is not provided
based on Exception 2 in 1018.1.

F202 Existing Buildings and Facilities

F202.1 General. Additions and alterations to existing buildings
or facilities, including leased buildings or facilities, shall
comply with F202.
F202.2 Additions. Each addition to an existing building or
facility shall comply with the requirements for new construction.
F202.2.1 Accessible Route. At least one accessible route shall
be provided within the site from accessible parking spaces and
accessible passenger loading zones; public streets and sidewalks;
and public transportation stops to an accessible entrance serving
the addition. If the only accessible entrances serving the addition
are provided in the existing building or facility, the accessible
route shall connect at least one existing entrance to all accessible
spaces and elements within the addition. In addition, elements and
spaces specified in F202.2.2 through F202.2.5 shall be on an
accessible route.
F202.2.2 Entrance. Where an entrance is not provided in an
addition, at least one entrance in the existing building or facility
shall comply with F206.4 and shall serve the addition.
F202.2.3 Toilet and Bathing Facilities. Where toilet facilities
and bathing facilities are not provided in an addition but are
provided in the existing building or facility to serve the addition,
the toilet facilities and bathing facilities shall comply with
F202.2.3.
EXCEPTION: In alterations to areas serving additions where it is
technically infeasible to comply with 603, altering existing toilet
or bathing rooms is not required where a single unisex toilet room
or bathing room complying with F213.2.1 is provided to serve the
addition.
F202.2.3.1 Existing Toilet Facility. Where existing toilet
facilities are provided in the existing building or facility, at
least one toilet facility for men and at least one toilet facility
for women shall comply with F213.2 and F213.3 and shall serve the
addition.
EXCEPTION: Where only one toilet facility is provided in the
existing building or facility, one toilet facility shall comply with
F213.2 and F213.3 and shall serve the addition.
F202.2.3.2 Existing Bathing Facility. Where existing bathing
facilities are provided in the existing building or facility, at
least one bathing facility for men and at least one bathing facility
for women shall comply with F213.2 and F213.3 and shall serve the
addition.
EXCEPTION: Where only one bathing facility is provided in the
existing building or facility, one bathing facility shall comply
with F213.2 and F213.3 and shall serve the addition.
F202.2.4 Public Telephone. Where a public telephone is not
provided in an addition but is provided in the existing building or
facility to serve the addition, at least one public telephone in the
existing building or facility shall comply with F217.
F202.2.5 Drinking Fountain. Where a drinking fountain is not
provided in an addition but is provided in the existing building or
facility to serve the addition, at least one drinking fountain in
the existing building or facility shall comply with 602.1 through
602.6.
F202.3 Alterations. Where existing elements or spaces are
altered, each altered element or space shall comply with the
applicable requirements of Chapter 2.
EXCEPTIONS: 1. Unless required by F202.4, where elements or
spaces are altered and the circulation path to the altered element
or space is not altered, an accessible route shall not be required.
2. In alterations, where compliance with applicable requirements
is technically infeasible, the alteration shall comply with the
requirements to the maximum extent feasible.
3. Residential dwelling units not required to be accessible in
compliance with a standard issued pursuant to the Architectural
Barriers Act or Section 504 of the Rehabilitation Act of 1973, as
amended, shall not be required to comply with F202.3.
4. Where elements or spaces are altered in camping facilities,
picnic facilities, viewing areas, or trailheads and the circulation
path to the altered element or space is not altered, the circulation
path shall not be required to comply with 1016.
F202.3.1 Prohibited Reduction in Access. An alteration that
decreases or has the effect of decreasing the accessibility of a
building or facility below the requirements for new construction at
the time of the alteration is prohibited.
F202.3.2 Extent of Application. An alteration of an existing
element, space, or area of a building or facility shall not impose a
requirement for accessibility greater than required for new
construction.
F202.4 Alterations Affecting Primary Function Areas. In addition
to the requirements of F202.3, an alteration that affects or could
affect the usability of or access to an area containing a primary
function shall be made so as to ensure that, to the maximum extent
feasible, the path of travel to the altered area, including the rest
rooms, telephones, and drinking fountains serving the altered area,
are readily accessible to and usable by individuals with
disabilities, unless such alterations are disproportionate to the
overall alterations in terms of cost and scope as determined under
criteria established by the Administrator of the General Services
Administration, the Secretary of Defense, the Secretary of Housing
and Urban Development, or the United States Postal Service.
EXCEPTIONS: 1. Residential dwelling units shall not be required
to comply with F202.4.
2. Camping facilities, picnic facilities, viewing areas,
trailheads, trails, and beach access routes shall not be required to
comply with F202.4.
F202.5 Alterations to Qualified Historic Buildings and
Facilities. Alterations to a qualified historic building or facility
shall comply with F202.3 and F202.4.
EXCEPTION: Where the State Historic Preservation Officer or
Advisory Council on Historic Preservation determines that compliance
with the requirements for accessible routes, entrances, or toilet
facilities would threaten or destroy the historic significance of
the building or facility, the exceptions for alterations to
qualified historic buildings or facilities for that element shall be
permitted to apply.
F202.6 Leases. Buildings or facilities for which new leases are
negotiated by the Federal government after the effective date of the
revised standards issued pursuant to the Architectural Barriers Act,
including new leases for buildings or facilities previously occupied
by the Federal government, shall comply with F202.6.
EXCEPTIONS: 1. Buildings or facilities leased for use by
officials servicing disasters on a temporary, emergency basis shall
not be required to comply with F202.6.
2. Buildings or facilities leased for 12 months or less shall
not be required to comply with F202.6 provided that the lease may
not be extended or renewed.
F202.6.1 Joint Use Areas. Joint use areas serving the leased
space shall comply with F202.6.
EXCEPTION: Alterations and additions to joint use areas serving
the leased space shall not be required to comply with F202.2,
F202.3, and F202.5 provided that the alterations are not undertaken
by or on behalf of the Federal government.
F202.6.2 Accessible Route. Primary function areas, as defined by
Administrator of the General Services Administration, the Secretary
of Defense, the Secretary of Housing and Urban Development, and the
United States Postal Service, shall be served by at least one
accessible route complying with F206. Elements and spaces required
to be accessible by F202.6 shall be on an accessible route complying
with F206.
EXCEPTION: Fire alarms required by F202.6.5.2 and assistive
listening systems required by F202.6.5.5 shall not be required to be
on an accessible route.
F202.6.3 Toilet and Bathing Facilities. Where provided, toilet
facilities and bathing facilities shall comply with F202.6.3.
F202.6.3.1 Multiple Facilities. At least one toilet facility or
bathing facility for each sex on each floor that has toilet
facilities or bathing facilities shall comply with F213.2 and
F213.3.
F202.6.3.2 Single Facilities. Where only one toilet or bathing
facility is provided in a building or facility for each sex, either
one unisex toilet or bathing facility, or one toilet or bathing
facility for each sex, shall comply with F213.2 and F213.3.
F202.6.4 Parking. Parking shall comply with F208.
F202.6.5 Other Elements and Spaces. Where provided, the
following elements and spaces shall comply with F202.6.5.
F202.6.5.1 Drinking Fountains. Drinking fountains shall comply
with F211.
F202.6.5.2 Fire Alarms. Fire alarms shall comply with F215.
EXCEPTION: Fire alarms shall not be required to comply with 702
where existing power sources must be upgraded to meet the
requirement.
F202.6.5.3 Public Telephones. Public telephones shall comply
with F217.

[[Page 59513]]

F202.6.5.4 Dining Surfaces and Work Surfaces. Dining surfaces
and work surfaces shall comply with F226.
F202.6.5.5 Assembly Areas. Assistive listening systems shall
comply with F219 and assembly seating shall comply with F221.
F202.6.5.6 Sales and Service Counters. Sales and service
counters shall comply with F227.
F202.6.5.7 Depositories, Vending Machines, Change Machines, and
Mail Boxes. Depositories, vending machines, change machines, and
mail boxes shall comply with F228.
F202.6.5.8 Residential Facilities. Residential dwelling units
shall comply with F233.

F203 General Exceptions

F203.1 General. Sites, buildings, facilities, and elements are
exempt from these requirements to the extent specified by F203.
F203.2 Existing Elements. Elements in compliance with an earlier
standard issued pursuant to the Architectural Barriers Act or
Section 504 of the Rehabilitation Act of 1973, as amended shall not
be required to comply with these requirements unless altered.
F203.3 Construction Sites. Structures and sites directly
associated with the actual processes of construction, including but
not limited to, scaffolding, bridging, materials hoists, materials
storage, and construction trailers shall not be required to comply
with these requirements or to be on an accessible route. Portable
toilet units provided for use exclusively by construction personnel
on a construction site shall not be required to comply with F213 or
to be on an accessible route.
F203.4 Raised Areas. Areas raised primarily for purposes of
security, life safety, or fire safety, including but not limited to,
observation or lookout galleries, prison guard towers, fire towers,
or life guard stands shall not be required to comply with these
requirements or to be on an accessible route.
F203.5 Limited Access Spaces. Spaces accessed only by ladders,
catwalks, crawl spaces, or very narrow passageways shall not be
required to comply with these requirements or to be on an accessible
route.
F203.6 Machinery Spaces. Spaces frequented only by service
personnel for maintenance, repair, or occasional monitoring of
equipment shall not be required to comply with these requirements or
to be on an accessible route. Machinery spaces include, but are not
limited to, elevator pits or elevator penthouses; mechanical,
electrical or communications equipment rooms; piping or equipment
catwalks; water or sewage treatment pump rooms and stations;
electric substations and transformer vaults; and highway and tunnel
utility facilities.
F203.7 Single Occupant Structures. Single occupant structures
accessed only by passageways below grade or elevated above standard
curb height, including but not limited to, toll booths that are
accessed only by underground tunnels, shall not be required to
comply with these requirements or to be on an accessible route.
F203.8 Detention and Correctional Facilities. In detention and
correctional facilities, common use areas that are used only by
inmates or detainees and security personnel and that do not serve
holding cells or housing cells required to comply with F232, shall
not be required to comply with these requirements or to be on an
accessible route.
F203.9 Residential Facilities. In residential facilities, common
use areas that do not serve residential dwelling units required to
provide mobility features complying with 809.2 through 809.4 shall
not be required to comply with these requirements or to be on an
accessible route.
F203.10 Raised Refereeing, Judging, and Scoring Areas. Raised
structures used solely for refereeing, judging, or scoring a sport
shall not be required to comply with these requirements or to be on
an accessible route.
F203.11 Water Slides. Water slides shall not be required to
comply with these requirements or to be on an accessible route.
F203.12 Animal Containment Areas. Animal containment areas that
are not for public use shall not be required to comply with these
requirements or to be on an accessible route.
F203.13 Raised Boxing or Wrestling Rings. Raised boxing or
wrestling rings shall not be required to comply with these
requirements or to be on an accessible route.
F203.14 Raised Diving Boards and Diving Platforms. Raised diving
boards and diving platforms shall not be required to comply with
these requirements or to be on an accessible route.

F204 Protruding Objects

F204.1 General. Protruding objects on circulation paths shall
comply with 307.
EXCEPTIONS: 1. Within areas of sport activity, protruding
objects on circulation paths shall not be required to comply with
307.
2. Within play areas, protruding objects on circulation paths
shall not be required to comply with 307 provided that ground level
accessible routes provide vertical clearance in compliance with
1008.2.

F205 Operable Parts

F205.1 General. Operable parts on accessible elements,
accessible routes, and in accessible rooms and spaces shall comply
with 309.
EXCEPTIONS: 1. Operable parts that are intended for use only by
service or maintenance personnel shall not be required to comply
with 309.
2. Electrical or communication receptacles serving a dedicated
use shall not be required to comply with 309.
3. Where two or more outlets are provided in a kitchen above a
length of counter top that is uninterrupted by a sink or appliance,
one outlet shall not be required to comply with 309.
4. Floor electrical receptacles shall not be required to comply
with 309.
5. HVAC diffusers shall not be required to comply with 309.
6. Except for light switches, where redundant controls are
provided for a single element, one control in each space shall not
be required to comply with 309.
7. Cleats and other boat securement devices shall not be
required to comply with 309.3.
8. Exercise machines and exercise equipment shall not be
required to comply with 309.

F206 Accessible Routes

F206.1 General. Accessible routes shall be provided in
accordance with F206 and shall comply with Chapter 4 except that the
exemptions at 403.5, 405.5, and 405.8 shall not apply.
EXCEPTIONS: 1. Accessible routes shall not be required where
outdoor recreation access routes are provided at camping facilities
in accordance with F244.5, picnic facilities in accordance with
F245.4, viewing areas in accordance with F246.3, or trailheads in
accordance with F247.3.2.
2. Accessible routes shall not be required where camping
facilities, picnic facilities, viewing areas, or outdoor constructed
features are provided on trails.
3. Accessible routes shall not be required where beach access
routes are provided in accordance with F248.
F206.2 Where Required. Accessible routes shall be provided where
required by F206.2.
F206.2.1 Site Arrival Points. At least one accessible route
shall be provided within the site from accessible parking spaces and
accessible passenger loading zones; public streets and sidewalks;
and public transportation stops to the accessible building or
facility entrance they serve.
EXCEPTIONS: 1. Where exceptions for alterations to qualified
historic buildings or facilities are permitted by F202.5, no more
than one accessible route from a site arrival point to an accessible
entrance shall be required.
2. An accessible route shall not be required between site
arrival points and the building or facility entrance if the only
means of access between them is a vehicular way not providing
pedestrian access.
F206.2.2 Within a Site. At least one accessible route shall
connect accessible buildings, accessible facilities, accessible
elements, and accessible spaces that are on the same site.
EXCEPTION: An accessible route shall not be required between
accessible buildings, accessible facilities, accessible elements and
accessible spaces if the only means of access between them is a
vehicular way not providing pedestrian access.
F206.2.3 Multi-Story Buildings and Facilities. At least one
accessible route shall connect each story and mezzanine in multi-
story buildings and facilities.
EXCEPTIONS: 1. Where a two story building or facility has one
story with an occupant load of five or fewer persons that does not
contain public use space, that story shall not be required to be
connected to the story above or below.
2. In detention and correctional facilities, an accessible route
shall not be required to connect stories where cells with mobility
features required to comply with 807.2, all common use areas serving
cells with mobility features required to comply with 807.2, and all
public use areas are on an accessible route.

[[Page 59514]]

3. In residential facilities, an accessible route shall not be
required to connect stories where residential dwelling units with
mobility features required to comply with 809.2 through 809.4, all
common use areas serving residential dwelling units with mobility
features required to comply with 809.2 through 809.4, and public use
areas serving residential dwelling units are on an accessible route.
4. Within multi-story transient lodging guest rooms with
mobility features required to comply with 806.2, an accessible route
shall not be required to connect stories provided that spaces
complying with 806.2 are on an accessible route and sleeping
accommodations for two persons minimum are provided on a story
served by an accessible route.
5. In air traffic control towers, an accessible route shall not
be required to serve the cab and the floor immediately below the
cab.
6. Where exceptions for alterations to qualified historic
buildings or facilities are permitted by F202.5, an accessible route
shall not be required to stories located above or below the
accessible story.
F206.2.3.1 Stairs and Escalators in Existing Buildings. In
alterations and additions, where an escalator or stair is provided
where none existed previously and major structural modifications are
necessary for the installation, an accessible route shall be
provided between the levels served by the escalator or stair unless
exempted by F206.2.3 Exceptions 1 through 6.
F206.2.4 Spaces and Elements. At least one accessible route
shall connect accessible building or facility entrances with all
accessible spaces and elements within the building or facility which
are otherwise connected by a circulation path unless exempted by
F206.2.3 Exceptions 1 through 6.
EXCEPTIONS: 1. Raised courtroom stations, including judges'
benches, clerks' stations, bailiffs' stations, deputy clerks'
stations, and court reporters' stations shall not be required to
provide vertical access provided that the required clear floor
space, maneuvering space, and, if appropriate, electrical service
are installed at the time of initial construction to allow future
installation of a means of vertical access complying with 405, 407,
408, or 410 without requiring substantial reconstruction of the
space.
2. In assembly areas with fixed seating required to comply with
F221, an accessible route shall not be required to serve fixed
seating where wheelchair spaces required to be on an accessible
route are not provided.
3. Accessible routes shall not be required to connect mezzanines
where buildings or facilities have no more than one story. In
addition, accessible routes shall not be required to connect stories
or mezzanines where multi-story buildings or facilities are exempted
by F206.2.3 Exceptions 1 through 6.
F206.2.5 Restaurants and Cafeterias. In restaurants and
cafeterias, an accessible route shall be provided to all dining
areas, including raised or sunken dining areas, and outdoor dining
areas.
EXCEPTIONS: 1. In alterations, an accessible route shall not be
required to existing raised or sunken dining areas, or to all parts
of existing outdoor dining areas where the same services and decor
are provided in an accessible space usable by the public and not
restricted to use by people with disabilities.
2. In sports facilities, tiered dining areas providing seating
required to comply with F221 shall be required to have accessible
routes serving at least 25 percent of the dining area provided that
accessible routes serve seating complying with F221 and each tier is
provided with the same services.
F206.2.6 Performance Areas. Where a circulation path directly
connects a performance area to an assembly seating area, an
accessible route shall directly connect the assembly seating area
with the performance area. An accessible route shall be provided
from performance areas to ancillary areas or facilities used by
performers unless exempted by F206.2.3 Exceptions 1 through 6.
F206.2.7 Press Boxes. Press boxes in assembly areas shall be on
an accessible route.
EXCEPTIONS: 1. An accessible route shall not be required to
press boxes in bleachers that have points of entry at only one level
provided that the aggregate area of all press boxes is 500 square
feet (46 m2) maximum.
2. An accessible route shall not be required to free-standing
press boxes that are elevated above grade 12 feet (3660 mm) minimum
provided that the aggregate area of all press boxes is 500 square
feet (46 m2) maximum.
F206.2.8 Amusement Rides. Amusement rides required to comply
with F234 shall provide accessible routes in accordance with
F206.2.8. Accessible routes serving amusement rides shall comply
with Chapter 4 except as modified by 1002.2.
F206.2.8.1 Load and Unload Areas. Load and unload areas shall be
on an accessible route. Where load and unload areas have more than
one loading or unloading position, at least one loading and
unloading position shall be on an accessible route.
F206.2.8.2 Wheelchair Spaces, Ride Seats Designed for Transfer,
and Transfer Devices. When amusement rides are in the load and
unload position, wheelchair spaces complying with 1002.4, amusement
ride seats designed for transfer complying with 1002.5, and transfer
devices complying with 1002.6 shall be on an accessible route.
F206.2.9 Recreational Boating Facilities. Boat slips required to
comply with F235.2 and boarding piers at boat launch ramps required
to comply with F235.3 shall be on an accessible route. Accessible
routes serving recreational boating facilities shall comply with
Chapter 4 except as modified by 1003.2.
F206.2.10 Bowling Lanes. Where bowling lanes are provided, at
least 5 percent, but no fewer than one of each type of bowling lane,
shall be on an accessible route.
F206.2.11 Court Sports. In court sports, at least one accessible
route shall directly connect both sides of the court.
F206.2.12 Exercise Machines and Equipment. Exercise machines and
equipment required to comply with F236 shall be on an accessible
route.
F206.2.13 Fishing Piers and Platforms. Fishing piers and
platforms shall be on an accessible route. Accessible routes serving
fishing piers and platforms shall comply with Chapter 4 except as
modified by 1005.1.
F206.2.14 Golf Facilities. At least one accessible route shall
connect accessible elements and spaces within the boundary of the
golf course. In addition, accessible routes serving golf car rental
areas; bag drop areas; course weather shelters complying with
F238.2.3; course toilet rooms; and practice putting greens, practice
teeing grounds, and teeing stations at driving ranges complying with
F238.3 shall comply with Chapter 4 except as modified by 1006.2.
EXCEPTION: Golf car passages complying with 1006.3 shall be
permitted to be used for all or part of accessible routes required
by F206.2.14.
F206.2.15 Miniature Golf Facilities. Holes required to comply
with F239.2, including the start of play, shall be on an accessible
route. Accessible routes serving miniature golf facilities shall
comply with Chapter 4 except as modified by 1007.2.
F206.2.16 Play Areas. Play areas shall provide accessible routes
in accordance with F206.2.16. Accessible routes serving play areas
shall comply with Chapter 4 except as modified by 1008.2.
F206.2.16.1 Ground Level and Elevated Play Components. At least
one accessible route shall be provided within the play area. The
accessible route shall connect ground level play components required
to comply with F240.2.1 and elevated play components required to
comply with F240.2.2, including entry and exit points of the play
components.
F206.2.16.2 Soft Contained Play Structures. Where three or fewer
entry points are provided for soft contained play structures, at
least one entry point shall be on an accessible route. Where four or
more entry points are provided for soft contained play structures,
at least two entry points shall be on an accessible route.
F206.3 Location. Accessible routes shall coincide with or be
located in the same area as general circulation paths. Where
circulation paths are interior, required accessible routes shall
also be interior.
F206.4 Entrances. Entrances shall be provided in accordance with
F206.4. Entrance doors, doorways, and gates shall comply with 404
and shall be on an accessible route complying with 402.
EXCEPTIONS: 1. Where an alteration includes alterations to an
entrance, and the building or facility has another entrance
complying with 404 that is on an accessible route, the altered
entrance shall not be required to comply with F206.4 unless required
by F202.4.
2. Where exceptions for alterations to qualified historic
buildings or facilities are permitted by F202.5, no more than one
public entrance shall be required to comply with F206.4. Where no
public entrance can comply with F206.4 under criteria established in
F202.5 Exception, then either an unlocked entrance not used by the
public shall comply with F206.4; or a locked entrance complying with
F206.4 with a notification system or remote monitoring shall be
provided.
F206.4.1 Public Entrances. In addition to entrances required by
F206.4.2 through

[[Page 59515]]

F206.4.9, at least 60 percent of all public entrances shall comply
with 404.
F206.4.2 Parking Structure Entrances. Where direct access is
provided for pedestrians from a parking structure to a building or
facility entrance, each direct access to the building or facility
entrance shall comply with 404.
F206.4.3 Entrances from Tunnels or Elevated Walkways. Where
direct access is provided for pedestrians from a pedestrian tunnel
or elevated walkway to a building or facility, at least one direct
entrance to the building or facility from each tunnel or walkway
shall comply with 404.
F206.4.4 Transportation Facilities. In addition to the
requirements of F206.4.2, F206.4.3, and F206.4.5 through F206.4.9,
transportation facilities shall provide entrances in accordance with
F206.4.4.
F206.4.4.1 Location. In transportation facilities, where
different entrances serve different transportation fixed routes or
groups of fixed routes, at least one public entrance serving each
fixed route or group of fixed routes shall comply with 404.
F206.4.4.2 Direct Connections. Direct connections to other
facilities shall provide an accessible route complying with 404 from
the point of connection to boarding platforms and all transportation
system elements required to be accessible. Any elements provided to
facilitate future direct connections shall be on an accessible route
connecting boarding platforms and all transportation system elements
required to be accessible.
F206.4.5 Tenant Spaces. At least one accessible entrance to each
tenancy in a facility shall comply with 404.
EXCEPTION: Self-service storage facilities not required to
comply with F225.3 shall not be required to be on an accessible
route.
F206.4.6 Residential Dwelling Unit Primary Entrance. In
residential dwelling units, at least one primary entrance shall
comply with 404. The primary entrance to a residential dwelling unit
shall not be to a bedroom.
F206.4.7 Restricted Entrances. Where restricted entrances are
provided to a building or facility, at least one restricted entrance
to the building or facility shall comply with 404.
F206.4.8 Service Entrances. If a service entrance is the only
entrance to a building or to a tenancy in a facility, that entrance
shall comply with 404.
F206.4.9 Entrances for Inmates or Detainees. Where entrances
used only by inmates or detainees and security personnel are
provided at judicial facilities, detention facilities, or
correctional facilities, at least one such entrance shall comply
with 404.
F206.5 Doors, Doorways, and Gates. Doors, doorways, and gates
providing user passage shall be provided in accordance with F206.5.
F206.5.1 Entrances. Each entrance to a building or facility
required to comply with F206.4 shall have at least one door,
doorway, or gate complying with 404.
F206.5.2 Rooms and Spaces. Within a building or facility, at
least one door, doorway, or gate serving each room or space
complying with these requirements shall comply with 404.
F206.5.3 Transient Lodging Facilities. In transient lodging
facilities, entrances, doors, and doorways providing user passage
into and within guest rooms that are not required to provide
mobility features complying with 806.2 shall comply with 404.2.3.
EXCEPTION: Shower and sauna doors in guest rooms that are not
required to provide mobility features complying with 806.2 shall not
be required to comply with 404.2.3.
F206.5.4 Residential Dwelling Units. In residential dwelling
units required to provide mobility features complying with 809.2
through 809.4, all doors and doorways providing user passage shall
comply with 404.
F206.6 Elevators. Elevators provided for passengers shall comply
with 407. Where multiple elevators are provided, each elevator shall
comply with 407.
EXCEPTIONS: 1. In a building or facility permitted to use the
exceptions to F206.2.3 or permitted by F206.7 to use a platform
lift, elevators complying with 408 shall be permitted.
2. Elevators complying with 408 or 409 shall be permitted in
multi-story residential dwelling units.
F206.6.1 Existing Elevators. Where elements of existing
elevators are altered, the same element shall also be altered in all
elevators that are programmed to respond to the same hall call
control as the altered elevator and shall comply with the
requirements of 407 for the altered element.
F206.7 Platform Lifts. Platform lifts shall comply with 410.
Platform lifts shall be permitted as a component of an accessible
route in new construction in accordance with F206.7. Platform lifts
shall be permitted as a component of an accessible route in an
existing building or facility.
F206.7.1 Performance Areas and Speakers' Platforms. Platform
lifts shall be permitted to provide accessible routes to performance
areas and speakers' platforms.
F206.7.2 Wheelchair Spaces. Platform lifts shall be permitted to
provide an accessible route to comply with the wheelchair space
dispersion and line-of-sight requirements of F221 and 802.
F206.7.3 Incidental Spaces. Platform lifts shall be permitted to
provide an accessible route to incidental spaces which are not
public use spaces and which are occupied by five persons maximum.
F206.7.4 Judicial Spaces. Platform lifts shall be permitted to
provide an accessible route to: jury boxes and witness stands;
raised courtroom stations including, judges' benches, clerks'
stations, bailiffs' stations, deputy clerks' stations, and court
reporters' stations; and to depressed areas such as the well of a
court.
F206.7.5 Existing Site Constraints. Platform lifts shall be
permitted where existing exterior site constraints make use of a
ramp or elevator infeasible.
F206.7.6 Guest Rooms and Residential Dwelling Units. Platform
lifts shall be permitted to connect levels within transient lodging
guest rooms required to provide mobility features complying with
806.2 or residential dwelling units required to provide mobility
features complying with 809.2 through 809.4.
F206.7.7 Amusement Rides. Platform lifts shall be permitted to
provide accessible routes to load and unload areas serving amusement
rides.
F206.7.8 Play Areas. Platform lifts shall be permitted to
provide accessible routes to play components or soft contained play
structures.
F206.7.9 Team or Player Seating. Platform lifts shall be
permitted to provide accessible routes to team or player seating
areas serving areas of sport activity.
F206.7.10 Recreational Boating Facilities and Fishing Piers and
Platforms. Platform lifts shall be permitted to be used instead of
gangways that are part of accessible routes serving recreational
boating facilities and fishing piers and platforms.
F206.8 Security Barriers. Security barriers, including but not
limited to, security bollards and security check points, shall not
obstruct a required accessible route or accessible means of egress.
EXCEPTION: Where security barriers incorporate elements that
cannot comply with these requirements such as certain metal
detectors, fluoroscopes, or other similar devices, the accessible
route shall be permitted to be located adjacent to security
screening devices. The accessible route shall permit persons with
disabilities passing around security barriers to maintain visual
contact with their personal items to the same extent provided others
passing through the security barrier.

F207 Accessible Means of Egress

F207.1 General. Means of egress shall comply with section
1003.2.13 of the International Building Code (2000 edition and 2001
Supplement) or section 1007 of the International Building Code (2003
edition) (incorporated by reference, see Referenced Standards'' in
Chapter 1).
EXCEPTIONS: 1. Where means of egress are permitted by local
building or life safety codes to share a common path of egress
travel, accessible means of egress shall be permitted to share a
common path of egress travel.
2. Areas of refuge shall not be required in detention and
correctional facilities.
F207.2 Platform Lifts. Standby power shall be provided for
platform lifts permitted by section 1003.2.13.4 of the International
Building Code (2000 edition and 2001 Supplement) or section 1007.5
of the International Building Code (2003 edition) (incorporated by
reference, see ``Referenced Standards'' in Chapter 1) to serve as a
part of an accessible means of egress.

F208 Parking Spaces

F208.1 General. Where parking spaces are provided, parking
spaces shall be provided in accordance with F208.
EXCEPTION: Parking spaces used exclusively for buses, trucks,
other delivery vehicles, law enforcement vehicles, or vehicular
impound shall not be required to comply with F208 provided that lots
accessed by the public are provided with a passenger loading zone
complying with 503.
F208.2 Minimum Number. Parking spaces complying with 502 shall
be provided in accordance with Table F208.2 except as

[[Page 59516]]

required by F208.2.1, F208.2.2, and F208.2.3. Where more than one
parking facility is provided on a site, the number of accessible
spaces provided on the site shall be calculated according to the
number of spaces required for each parking facility.

Table F208.2--Parking Spaces
------------------------------------------------------------------------
Total number of parking spaces provided in Minimum number of required
parking facility accessible parking spaces
------------------------------------------------------------------------
1 to 25................................... 1.
26 to 50.................................. 2.
51 to 75.................................. 3.
76 to 100................................. 4.
101 to 150................................ 5.
151 to 200................................ 6.
201 to 300................................ 7.
301 to 400................................ 8.
401 to 500................................ 9.
501 to 1000............................... 2 percent of total.
1001 and over............................. 20, plus 1 for each 100, or
fraction thereof, over
1000.
------------------------------------------------------------------------

F208.2.1 Hospital Outpatient Facilities. Ten percent of patient
and visitor parking spaces provided to serve hospital outpatient
facilities shall comply with 502.
F208.2.2 Rehabilitation Facilities and Outpatient Physical
Therapy Facilities. Twenty percent of patient and visitor parking
spaces provided to serve rehabilitation facilities specializing in
treating conditions that affect mobility and outpatient physical
therapy facilities shall comply with 502.
F208.2.3 Residential Facilities. Parking spaces provided to
serve residential facilities shall comply with F208.2.3.
F208.2.3.1 Parking for Residents. Where at least one parking
space is provided for each residential dwelling unit, at least one
parking space complying with 502 shall be provided for each
residential dwelling unit required to provide mobility features
complying with 809.2 through 809.4.
F208.2.3.2 Additional Parking Spaces for Residents. Where the
total number of parking spaces provided for each residential
dwelling unit exceeds one parking space per residential dwelling
unit, 2 percent, but no fewer than one space, of all the parking
spaces not covered by F208.2.3.1 shall comply with 502.
F208.2.3.3 Parking for Guests, Employees, and Other Non-
Residents. Where parking spaces are provided for persons other than
residents, parking shall be provided in accordance with Table
F208.2.
F208.2.4 Van Parking Spaces. For every six or fraction of six
parking spaces required by F208.2 to comply with 502, at least one
shall be a van parking space complying with 502.
F208.3 Location. Parking facilities shall comply with F208.3.
F208.3.1 General. Parking spaces complying with 502 that serve a
particular building or facility shall be located on the shortest
accessible route from parking to an entrance complying with F206.4.
Where parking serves more than one accessible entrance, parking
spaces complying with 502 shall be dispersed and located on the
shortest accessible route to the accessible entrances. In parking
facilities that do not serve a particular building or facility,
parking spaces complying with 502 shall be located on the shortest
accessible route to an accessible pedestrian entrance of the parking
facility.
EXCEPTIONS: 1. All van parking spaces shall be permitted to be
grouped on one level within a multi-story parking facility.
2. Parking spaces shall be permitted to be located in different
parking facilities if substantially equivalent or greater
accessibility is provided in terms of distance from an accessible
entrance or entrances, parking fee, and user convenience.
F208.3.2 Residential Facilities. In residential facilities
containing residential dwelling units required to provide mobility
features complying with 809.2 through 809.4, parking spaces provided
in accordance with F208.2.3.1 shall be located on the shortest
accessible route to the residential dwelling unit entrance they
serve. Spaces provided in accordance with F208.2.3.2 shall be
dispersed throughout all types of parking provided for the
residential dwelling units.
EXCEPTION: Parking spaces provided in accordance with F208.2.3.2
shall not be required to be dispersed throughout all types of
parking if substantially equivalent or greater accessibility is
provided in terms of distance from an accessible entrance, parking
fee, and user convenience.

F209 Passenger Loading Zones and Bus Stops

F209.1 General. Passenger loading zones shall be provided in
accordance with F209.
F209.2 Type. Where provided, passenger loading zones shall
comply with F209.2.
F209.2.1 Passenger Loading Zones. Passenger loading zones,
except those required to comply with F209.2.2 and F209.2.3, shall
provide at least one passenger loading zone complying with 503 in
every continuous 100 linear feet (30 m) of loading zone space, or
fraction thereof.
F209.2.2 Bus Loading Zones. In bus loading zones restricted to
use by designated or specified public transportation vehicles, each
bus bay, bus stop, or other area designated for lift or ramp
deployment shall comply with 810.2.
F209.2.3 On-Street Bus Stops. On-street bus stops shall comply
with 810.2 to the maximum extent practicable.
F209.3 Medical Care and Long-Term Care Facilities. At least one
passenger loading zone complying with 503 shall be provided at an
accessible entrance to licensed medical care and licensed long-term
care facilities where the period of stay exceeds twenty-four hours.
F209.4 Valet Parking. Parking facilities that provide valet
parking services shall provide at least one passenger loading zone
complying with 503.
F209.5 Mechanical Access Parking Garages. Mechanical access
parking garages shall provide at least one passenger loading zone
complying with 503 at vehicle drop-off and vehicle pick-up areas.

F210 Stairways

F210.1 General. Interior and exterior stairs that are part of a
means of egress shall comply with 504.
EXCEPTIONS: 1. In detention and correctional facilities, stairs
that are not located in public use areas shall not be required to
comply with 504.
2. In alterations, stairs between levels that are connected by
an accessible route shall not be required to comply with 504, except
that handrails complying with 505 shall be provided when the stairs
are altered.
3. In assembly areas, aisle stairs shall not be required to
comply with 504.
4. Stairs that connect play components shall not be required to
comply with 504.

F211 Drinking Fountains

F211.1 General. Where drinking fountains are provided on an
exterior site, on a floor, and within a secured area they shall be
provided in accordance with F211.
EXCEPTION: In detention or correctional facilities, drinking
fountains only serving holding or housing cells not required to
comply with F232 shall not be required to comply with F211.
F211.2 Minimum Number. No fewer than two drinking fountains
shall be provided. One drinking fountain shall comply with 602.1
through 602.6 and one drinking fountain shall comply with 602.7.
EXCEPTION: Where a single drinking fountain complies with 602.1
through 602.6 and 602.7, it shall be permitted to be substituted for
two separate drinking fountains.
F211.3 More Than Minimum Number. Where more than the minimum
number of drinking fountains specified in F211.2 are provided, 50
percent of the total number of drinking fountains provided shall
comply with 602.1 through 602.6, and 50 percent of the total number
of drinking fountains provided shall comply with 602.7.
EXCEPTION: Where 50 percent of the drinking fountains yields a
fraction, 50 percent shall be permitted to be rounded up or down
provided that the total number of drinking fountains complying with
F211 equals 100 percent of drinking fountains.

F212 Kitchens, Kitchenettes, and Sinks

F212.1 General. Where provided, kitchens, kitchenettes, and
sinks shall comply with F212.
F212.2 Kitchens and Kitchenettes. Kitchens and kitchenettes
shall comply with 804.
F212.3 Sinks. Where sinks are provided, at least 5 percent, but
no fewer than one, of each type provided in each accessible room or
space shall comply with 606.
EXCEPTIONS: 1. Mop or service sinks shall not be required to
comply with F212.3.
2. In camping facilities and picnic facilities, sinks shall not
be required to comply with F212.3 where a cooktop or conventional
range is not provided.

F213 Toilet Facilities and Bathing Facilities

F213.1 General. Where toilet facilities and bathing facilities
are provided, they shall comply with F213. Where toilet facilities
and

[[Page 59517]]

bathing facilities are provided in facilities permitted by F206.2.3
Exceptions 1 and 2 not to connect stories by an accessible route,
toilet facilities and bathing facilities shall be provided on a
story connected by an accessible route to an accessible entrance.
EXCEPTION: Pit toilets provided on trails and in camping
facilities shall not be required to comply with F213.
F213.2 Toilet Rooms and Bathing Rooms. Where toilet rooms are
provided, each toilet room shall comply with 603. Where bathing
rooms are provided, each bathing room shall comply with 603.
EXCEPTIONS: 1. In alterations where it is technically infeasible
to comply with 603, altering existing toilet or bathing rooms shall
not be required where a single unisex toilet room or bathing room
complying with F213.2.1 is provided and located in the same area and
on the same floor as existing inaccessible toilet or bathing rooms.
2. Where exceptions for alterations to qualified historic
buildings or facilities are permitted by F202.5 and toilet rooms are
provided, no fewer than one toilet room for each sex complying with
603 or one unisex toilet room complying with F213.2.1 shall be
provided.
3. Where multiple single user portable toilet or bathing units
are clustered at a single location, no more than 5 percent of the
toilet units and bathing units at each cluster shall be required to
comply with 603. Portable toilet units and bathing units complying
with 603 shall be identified by the International Symbol of
Accessibility complying with 703.7.2.1.
4. Where multiple single user toilet rooms are clustered at a
single location, no more than 50 percent of the single user toilet
rooms for each use at each cluster shall be required to comply with
603.
F213.2.1 Unisex (Single-Use or Family) Toilet and Bathing Rooms.
Unisex toilet rooms shall contain not more than one lavatory, and
two water closets without urinals or one water closet and one
urinal. Unisex bathing rooms shall contain one shower or one shower
and one bathtub, one lavatory, and one water closet. Doors to unisex
toilet rooms and unisex bathing rooms shall have privacy latches.
F213.3 Plumbing Fixtures and Accessories. Plumbing fixtures and
accessories provided in a toilet room or bathing room required to
comply with F213.2 shall comply with F213.3.
F213.3.1 Toilet Compartments. Where toilet compartments are
provided, at least one toilet compartment shall comply with 604.8.1.
In addition to the compartment required to comply with 604.8.1, at
least one compartment shall comply with 604.8.2 where six or more
toilet compartments are provided, or where the combination of
urinals and water closets totals six or more fixtures.
F213.3.2 Water Closets. Where water closets are provided at
least one shall comply with 604.
F213.3.3 Urinals. Where more than one urinal is provided, at
least one shall comply with 605.
F213.3.4 Lavatories. Where lavatories are provided, at least one
shall comply with 606 and shall not be located in a toilet
compartment.
F213.3.5 Mirrors. Where mirrors are provided, at least one shall
comply with 603.3.
F213.3.6 Bathing Facilities. Where bathtubs or showers are
provided, at least one bathtub complying with 607 or at least one
shower complying with 608 shall be provided.
F213.3.7 Coat Hooks and Shelves. Where coat hooks or shelves are
provided in toilet rooms without toilet compartments, at least one
of each type shall comply with 603.4. Where coat hooks or shelves
are provided in toilet compartments, at least one of each type
complying with 604.8.3 shall be provided in toilet compartments
required to comply with F213.3.1. Where coat hooks or shelves are
provided in bathing facilities, at least one of each type complying
with 603.4 shall serve fixtures required to comply with F213.3.6.

F214 Washing Machines and Clothes Dryers

F214.1 General. Where provided, washing machines and clothes
dryers shall comply with F214.
EXCEPTION: Washing machines and clothes dryers provided in
employee work areas shall not be required to comply with F214.
F214.2 Washing Machines. Where three or fewer washing machines
are provided, at least one shall comply with 611. Where more than
three washing machines are provided, at least two shall comply with
611.
F214.3 Clothes Dryers. Where three or fewer clothes dryers are
provided, at least one shall comply with 611. Where more than three
clothes dryers are provided, at least two shall comply with 611.

F215 Fire Alarm Systems

F215.1 General. Where fire alarm systems provide audible alarm
coverage, alarms shall comply with F215.
EXCEPTION: In existing facilities, visible alarms shall not be
required except where an existing fire alarm system is upgraded or
replaced, or a new fire alarm system is installed.
F215.2 Public and Common Use Areas. Alarms in public use areas
and common use areas shall comply with 702.
F215.3 Employee Work Areas. Where employee work areas have
audible alarm coverage, the wiring system shall be designed so that
visible alarms complying with 702 can be integrated into the alarm
system.
F215.4 Transient Lodging. Guest rooms required to comply with
F224.4 shall provide alarms complying with 702.
F215.5 Residential Facilities. Where provided in residential
dwelling units required to comply with 809.5, alarms shall comply
with 702.

F216 Signs

F216.1 General. Signs shall be provided in accordance with F216
and shall comply with 703.
EXCEPTIONS: 1. Building directories, menus, seat and row
designations in assembly areas, occupant names, building addresses,
and company names and logos shall not be required to comply with
F216.
2. In parking facilities, signs shall not be required to comply
with F216.2, F216.3, and F216.6 through F216.12.
3. Temporary, 7 days or less, signs shall not be required to
comply with F216.
4. In detention and correctional facilities, signs not located
in public use areas shall not be required to comply with F216.
F216.2 Designations. Interior and exterior signs identifying
permanent rooms and spaces shall comply with 703.1, 703.2, and
703.5. Where pictograms are provided as designations of permanent
interior rooms and spaces, the pictograms shall comply with 703.6
and shall have text descriptors complying with 703.2 and 703.5.
EXCEPTION: Exterior signs that are not located at the door to
the space they serve shall not be required to comply with 703.2.
F216.3 Directional and Informational Signs. Signs that provide
direction to or information about interior spaces and facilities of
the site shall comply with 703.5.
F216.4 Means of Egress. Signs for means of egress shall comply
with F216.4.
F216.4.1 Exit Doors. Doors at exit passageways, exit discharge,
and exit stairways shall be identified by tactile signs complying
with 703.1, 703.2, and 703.5.
F216.4.2 Areas of Refuge. Signs required by section
1003.2.13.5.4 of the International Building Code (2000 edition) or
section 1007.6.4 of the International Building Code (2003 edition)
(incorporated by reference, see ``Referenced Standards'' in Chapter
1) to provide instructions in areas of refuge shall comply with
703.5.
F216.4.3 Directional Signs. Signs required by section
1003.2.13.6 of the International Building Code (2000 edition) or
section 1007.7 of the International Building Code (2003 edition)
(incorporated by reference, see ``Referenced Standards'' in Chapter
1) to provide directions to accessible means of egress shall comply
with 703.5.
F216.5 Parking. Parking spaces complying with 502 shall be
identified by signs complying with 502.6.
EXCEPTIONS: 1. Where a total of four or fewer parking spaces,
including accessible parking spaces, are provided on a site,
identification of accessible parking spaces shall not be required.
2. In residential facilities, where parking spaces are assigned
to specific residential dwelling units, identification of accessible
parking spaces shall not be required.
F216.6 Entrances. Where not all entrances comply with 404,
entrances complying with 404 shall be identified by the
International Symbol of Accessibility complying with 703.7.2.1.
Directional signs complying with 703.5 that indicate the location of
the nearest entrance complying with 404 shall be provided at
entrances that do not comply with 404.
F216.7 Elevators. Where existing elevators do not comply with
407, elevators complying with 407 shall be clearly identified with
the International Symbol of Accessibility complying with 703.7.2.1.
F216.8 Toilet Rooms and Bathing Rooms. Where existing toilet
rooms or bathing rooms do not comply with 603, directional signs
indicating the location of the nearest toilet room or bathing room
complying with 603

[[Page 59518]]

within the facility shall be provided. Signs shall comply with 703.5
and shall include the International Symbol of Accessibility
complying with 703.7.2.1. Where existing toilet rooms or bathing
rooms do not comply with 603, the toilet rooms or bathing rooms
complying with 603 shall be identified by the International Symbol
of Accessibility complying with 703.7.2.1. Where clustered single
user toilet rooms or bathing facilities are permitted to use
exception to F213.2, toilet rooms or bathing facilities complying
with 603 shall be identified by the International Symbol of
Accessibility complying with 703.7.2.1 unless all toilet rooms and
bathing facilities comply with 603.
F216.9 TTYs. Identification and directional signs for public
TTYs shall be provided in accordance with F216.9.
F216.9.1 Identification Signs. Public TTYs shall be identified
by the International Symbol of TTY complying with 703.7.2.2.
F216.9.2 Directional Signs. Directional signs indicating the
location of the nearest public TTY shall be provided at all banks of
public pay telephones not containing a public TTY. In addition,
where signs provide direction to public pay telephones, they shall
also provide direction to public TTYs. Directional signs shall
comply with 703.5 and shall include the International Symbol of TTY
complying with 703.7.2.2.
F216.10 Assistive Listening Systems. Each assembly area required
by F219 to provide assistive listening systems shall provide signs
informing patrons of the availability of the assistive listening
system. Assistive listening signs shall comply with 703.5 and shall
include the International Symbol of Access for Hearing Loss
complying with 703.7.2.4.
EXCEPTION: Where ticket offices or windows are provided, signs
shall not be required at each assembly area provided that signs are
displayed at each ticket office or window informing patrons of the
availability of assistive listening systems.
F216.11 Check-Out Aisles. Where more than one check-out aisle is
provided, check-out aisles complying with 904.3 shall be identified
by the International Symbol of Accessibility complying with
703.7.2.1. Where check-out aisles are identified by numbers,
letters, or functions, signs identifying check-out aisles complying
with 904.3 shall be located in the same location as the checkout
aisle identification.
EXCEPTION: Where all check-out aisles serving a single function
comply with 904.3, signs complying with 703.7.2.1 shall not be
required.
F216.12 Amusement Rides. Signs identifying the type of access
provided on amusement rides shall be provided at entries to queues
and waiting lines. In addition, where accessible unload areas also
serve as accessible load areas, signs indicating the location of the
accessible load and unload areas shall be provided at entries to
queues and waiting lines.
F216.13 Trailhead Signs. Where new trail information signs are
provided at trailheads on newly constructed or altered trails
designed for use by hikers or pedestrians, the signs shall comply
with 1017.10.

F217 Telephones

F217.1 General. Where coin-operated public pay telephones,
coinless public pay telephones, public closed-circuit telephones,
public courtesy phones, or other types of public telephones are
provided, public telephones shall be provided in accordance with
F217 for each type of public telephone provided. For purposes of
this section, a bank of telephones shall be considered to be two or
more adjacent telephones.
F217.2 Wheelchair Accessible Telephones. Where public telephones
are provided, wheelchair accessible telephones complying with 704.2
shall be provided in accordance with Table F217.2.
EXCEPTION: Drive-up only public telephones shall not be required
to comply with F217.2.

Table F217.2--Wheelchair Accessible Telephones
------------------------------------------------------------------------
Minimum number of required
Number of telephones provided on a floor, wheelchair accessible
level, or exterior site telephones
------------------------------------------------------------------------
1 or more single units.................... 1 per floor, level, and
exterior site.
1 bank.................................... 1 per floor, level, and
exterior site.
2 or more banks........................... 1 per bank.
------------------------------------------------------------------------

F217.3 Volume Controls. All public telephones shall have volume
controls complying with 704.3.
F217.4 TTYs. TTYs complying with 704.4 shall be provided in
accordance with F217.4.
F217.4.1 Bank Requirement. Where four or more public pay
telephones are provided at a bank of telephones, at least one public
TTY complying with 704.4 shall be provided at that bank.
EXCEPTION: TTYs shall not be required at banks of telephones
located within 200 feet (61 m) of, and on the same floor as, a bank
containing a public TTY.
F217.4.2 Floor Requirement. Where at least one public pay
telephone is provided on a floor of a building, at least one public
TTY shall be provided on that floor.
F217.4.3 Building Requirement. Where at least one public pay
telephone is provided in a public use area of a building, at least
one public TTY shall be provided in the building in a public use
area.
F217.4.4 Exterior Site Requirement. Where four or more public
pay telephones are provided on an exterior site, at least one public
TTY shall be provided on the site.
F217.4.5 Rest Stops, Emergency Roadside Stops, and Service
Plazas. Where at least one public pay telephone is provided at a
public rest stop, emergency roadside stop, or service plaza, at
least one public TTY shall be provided.
F217.4.6 Hospitals. Where at least one public pay telephone is
provided serving a hospital emergency room, hospital recovery room,
or hospital waiting room, at least one public TTY shall be provided
at each location.
F217.4.7 Transportation Facilities. In transportation
facilities, in addition to the requirements of F217.4.1 through
F217.4.4, where at least one public pay telephone serves a
particular entrance to a bus or rail facility, at least one public
TTY shall be provided to serve that entrance. In airports, in
addition to the requirements of F217.4.1 through F217.4.4, where
four or more public pay telephones are located in a terminal outside
the security areas, a concourse within the security areas, or a
baggage claim area in a terminal, at least one public TTY shall be
provided in each location.
F217.4.8 Detention and Correctional Facilities. In detention and
correctional facilities, where at least one pay telephone is
provided in a secured area used only by detainees or inmates and
security personnel, at least one TTY shall be provided in at least
one secured area.
F217.5 Shelves for Portable TTYs. Where a bank of telephones in
the interior of a building consists of three or more public pay
telephones, at least one public pay telephone at the bank shall be
provided with a shelf and an electrical outlet in accordance with
704.5.
EXCEPTIONS: 1. Secured areas of detention and correctional
facilities where shelves and outlets are prohibited for purposes of
security or safety shall not be required to comply with F217.5.
2. The shelf and electrical outlet shall not be required at a
bank of telephones with a TTY.

F218 Transportation Facilities

F218.1 General. Transportation facilities shall comply with
F218.
F218.2 New and Altered Fixed Guideway Stations. New and altered
stations in rapid rail, light rail, commuter rail, intercity rail,
high speed rail, and other fixed guideway systems shall comply with
810.5 through 810.10.
F218.3 Bus Shelters. Where provided, bus shelters shall comply
with 810.3 and 810.4.
F218.4 Other Transportation Facilities. In other transportation
facilities, public address systems shall comply with 810.7 and
clocks shall comply with 810.8.

F219 Assistive Listening Systems

F219.1 General. Assistive listening systems shall be provided in
accordance with F219 and shall comply with 706.
F219.2 Required Systems. In each assembly area where audible
communication is integral to the use of the space, an assistive
listening system shall be provided.
EXCEPTION: Other than in courtrooms, assistive listening systems
shall not be required where audio amplification is not provided.
F219.3 Receivers. Receivers complying with 706.2 shall be
provided for assistive listening systems in each assembly area in
accordance with Table F219.3. Twenty-five percent minimum of
receivers provided, but no fewer than two, shall be hearing-aid
compatible in accordance with 706.3.
EXCEPTIONS: 1. Where a building contains more than one assembly
area and the assembly areas required to provide assistive listening
systems are under one management, the total number of required
receivers shall be permitted to be calculated according to the total
number of seats in the assembly areas in the building provided that
all receivers are usable with all systems.

[[Page 59519]]

2. Where all seats in an assembly area are served by an
induction loop assistive listening system, the minimum number of
receivers required by Table F219.3 to be hearing-aid compatible
shall not be required to be provided.

Table F219.3--Receivers for Assistive Listening Systems
------------------------------------------------------------------------
Minimum number of
required receivers
Capacity of seating in Minimum number of required to be
assembly area required receivers hearing-aid
compatible
------------------------------------------------------------------------
50 or less.................. 2................... 2.
51 to 200................... 2, plus 1 per 25 2.
seats over 50 seats.
201 to 500.................. 2, plus 1 per 25 1 per 4
seats over 50 seats receivers.\1\
\1\.
501 to 1000................. 20, plus 1 per 33 1 per 4
seats over 500 receivers.\1\
seats \1\.
1001 to 2000................ 35, plus 1 per 50 1 per 4
seats over 1000 receivers.\1\
seats \1\.
2001 and over............... 55, plus 1 per 100 1 per 4
seats over 2000 receivers.\1\
seats \1\.
------------------------------------------------------------------------
\1\ Or fraction thereof.

F220 Automatic Teller Machines and Fare Machines

F220.1 General. Where automatic teller machines or self-service
fare vending, collection, or adjustment machines are provided, at
least one of each type provided at each location shall comply with
707. Where bins are provided for envelopes, waste paper, or other
purposes, at least one of each type shall comply with 811.

F221 Assembly Areas

F221.1 General. Assembly areas shall provide wheelchair spaces,
companion seats, and designated aisle seats complying with F221 and
802. In addition, lawn seating shall comply with F221.5.
F221.2 Wheelchair Spaces. Wheelchair spaces complying with
F221.2 shall be provided in assembly areas with fixed seating.
F221.2.1 Number and Location. Wheelchair spaces shall be
provided complying with F221.2.1.
F221.2.1.1 General Seating. Wheelchair spaces complying with
802.1 shall be provided in accordance with Table F221.2.1.1.

Table F221.2.1.1--Number of Wheelchair Spaces in Assembly Areas
------------------------------------------------------------------------
Minimum number of required
Number of seats wheelchair spaces
------------------------------------------------------------------------
4 to 25................................... 1.
26 to 50.................................. 2.
51 to 150................................. 4.
151 to 300................................ 5.
301 to 500................................ 6.
501 to 5000............................... 6, plus 1 for each 150, or
fraction thereof, between
501 through 5000.
5001 and over............................. 36, plus 1 for each 200, or
fraction thereof, over
5000.
------------------------------------------------------------------------

F221.2.1.2 Luxury Boxes, Club Boxes, and Suites in Arenas,
Stadiums, and Grandstands. In each luxury box, club box, and suite
within arenas, stadiums, and grandstands, wheelchair spaces
complying with 802.1 shall be provided in accordance with Table
F221.2.1.1.
F221.2.1.3 Other Boxes. In boxes other than those required to
comply with F221.2.1.2, the total number of wheelchair spaces
required shall be determined in accordance with Table F221.2.1.1.
Wheelchair spaces shall be located in not less than 20 percent of
all boxes provided. Wheelchair spaces shall comply with 802.1.
F221.2.1.4 Team or Player Seating. At least one wheelchair space
complying with 802.1 shall be provided in team or player seating
areas serving areas of sport activity.
EXCEPTION: Wheelchair spaces shall not be required in team or
player seating areas serving bowling lanes not required to comply
with F206.2.10.
F221.2.2 Integration. Wheelchair spaces shall be an integral
part of the seating plan.
F221.2.3 Lines of Sight and Dispersion. Wheelchair spaces shall
provide lines of sight complying with 802.2 and shall comply with
F221.2.3. In providing lines of sight, wheelchair spaces shall be
dispersed. Wheelchair spaces shall provide spectators with choices
of seating locations and viewing angles that are substantially
equivalent to, or better than, the choices of seating locations and
viewing angles available to all other spectators. When the number of
wheelchair spaces required by F221.2.1 has been met, further
dispersion shall not be required.
EXCEPTION: Wheelchair spaces in team or player seating areas
serving areas of sport activity shall not be required to comply with
F221.2.3.
F221.2.3.1 Horizontal Dispersion. Wheelchair spaces shall be
dispersed horizontally.
EXCEPTIONS: 1. Horizontal dispersion shall not be required in
assembly areas with 300 or fewer seats if the companion seats
required by F221.3 and wheelchair spaces are located within the 2nd
or 3rd quartile of the total row length. Intermediate aisles shall
be included in determining the total row length. If the row length
in the 2nd and 3rd quartile of a row is insufficient to accommodate
the required number of companion seats and wheelchair spaces, the
additional companion seats and wheelchair spaces shall be permitted
to be located in the 1st and 4th quartile of the row.
2. In row seating, two wheelchair spaces shall be permitted to
be located side-by-side.
F221.2.3.2 Vertical Dispersion. Wheelchair spaces shall be
dispersed vertically at varying distances from the screen,
performance area, or playing field. In addition, wheelchair spaces
shall be located in each balcony or mezzanine that is located on an
accessible route.
EXCEPTIONS: 1. Vertical dispersion shall not be required in
assembly areas with 300 or fewer seats if the wheelchair spaces
provide viewing angles that are equivalent to, or better than, the
average viewing angle provided in the facility.
2. In bleachers, wheelchair spaces shall not be required to be
provided in rows other than rows at points of entry to bleacher
seating.
F221.3 Companion Seats. At least one companion seat complying
with 802.3 shall be provided for each wheelchair space required by
F221.2.1.
F221.4 Designated Aisle Seats. At least 5 percent of the total
number of aisle seats provided shall comply with 802.4 and shall be
the aisle seats located closest to accessible routes.
EXCEPTION: Team or player seating areas serving areas of sport
activity shall not be required to comply with F221.4.
F221.5 Lawn Seating. Lawn seating areas and exterior overflow
seating areas, where fixed seats are not provided, shall connect to
an accessible route.

F222 Dressing, Fitting, and Locker Rooms

F222.1 General. Where dressing rooms, fitting rooms, or locker
rooms are provided, at least 5 percent, but no fewer than one, of
each type of use in each cluster provided shall comply with 803.
EXCEPTION: In alterations, where it is technically infeasible to
provide rooms in accordance with F222.1, one room for each sex on
each level shall comply with 803. Where only unisex rooms are
provided, unisex rooms shall be permitted.
F222.2 Coat Hooks and Shelves. Where coat hooks or shelves are
provided in dressing, fitting or locker rooms without individual
compartments, at least one of each type shall comply with 803.5.
Where coat hooks or shelves are provided in individual compartments
at least one of each type complying with 803.5 shall be provided in
individual compartments in dressing, fitting, or locker rooms
required to comply with F222.1.

F223 Medical Care and Long-Term Care Facilities

F223.1 General. In licensed medical care facilities and licensed
long-term care facilities where the period of stay exceeds twenty-
four hours, patient or resident

[[Page 59520]]

sleeping rooms shall be provided in accordance with F223.
EXCEPTION: Toilet rooms that are part of critical or intensive
care patient sleeping rooms shall not be required to comply with
603.
F223.1.1 Alterations. Where sleeping rooms are altered or added,
the requirements of F223 shall apply only to the sleeping rooms
being altered or added until the number of sleeping rooms complies
with the minimum number required for new construction.
F223.2 Hospitals, Rehabilitation Facilities, Psychiatric
Facilities and Detoxification Facilities. Hospitals, rehabilitation
facilities, psychiatric facilities and detoxification facilities
shall comply with F223.2.
F223.2.1 Facilities Not Specializing in Treating Conditions That
Affect Mobility. In facilities not specializing in treating
conditions that affect mobility, at least 10 percent, but no fewer
than one, of the patient sleeping rooms shall provide mobility
features complying with 805.
F223.2.2 Facilities Specializing in Treating Conditions That
Affect Mobility. In facilities specializing in treating conditions
that affect mobility, 100 percent of the patient sleeping rooms
shall provide mobility features complying with 805.
F223.3 Long-Term Care Facilities. In licensed long-term care
facilities, at least 50 percent, but no fewer than one, of each type
of resident sleeping room shall provide mobility features complying
with 805.

F224 Transient Lodging Guest Rooms

F224.1 General. Transient lodging facilities shall provide guest
rooms in accordance with F224.
F224.1.1 Alterations. Where guest rooms are altered or added,
the requirements of F224 shall apply only to the guest rooms being
altered or added until the number of guest rooms complies with the
minimum number required for new construction.
F224.1.2 Guest Room Doors and Doorways. Entrances, doors, and
doorways providing user passage into and within guest rooms that are
not required to provide mobility features complying with 806.2 shall
comply with 404.2.3.
EXCEPTION: Shower and sauna doors in guest rooms that are not
required to provide mobility features complying with 806.2 shall not
be required to comply with 404.2.3.
F224.2 Guest Rooms with Mobility Features. In transient lodging
facilities, guest rooms with mobility features complying with 806.2
shall be provided in accordance with Table F224.2.

Table F224.2--Guest Rooms With Mobility Features
----------------------------------------------------------------------------------------------------------------
Minimum number of Minimum number of
Total number of guest rooms provided required rooms without required rooms with Total number of
roll-in showers roll-in showers required rooms
----------------------------------------------------------------------------------------------------------------
1 to 25.............................. 1...................... 0...................... 1.
26 to 50............................. 2...................... 0...................... 2.
51 to 75............................. 3...................... 1...................... 4.
76 to 100............................ 4...................... 1...................... 5.
101 to 150........................... 5...................... 2...................... 7.
151 to 200........................... 6...................... 2...................... 8.
201 to 300........................... 7...................... 3...................... 10.
301 to 400........................... 8...................... 4...................... 12.
401 to 500........................... 9...................... 4...................... 13.
501 to 1000.......................... 2 percent of total..... 1 percent of total..... 3 percent of total.
1001 and over........................ 20, plus 1 for each 10, plus 1 for each 30, plus 2 for each
100, or fraction 100, or fraction 100, or fraction
thereof, over 1000. thereof, over 1000. thereof, over 1000.
----------------------------------------------------------------------------------------------------------------

F224.3 Beds. In guest rooms having more than 25 beds, 5 percent
minimum of the beds shall have clear floor space complying with
806.2.3.
F224.4 Guest Rooms with Communication Features. In transient
lodging facilities, guest rooms with communication features
complying with 806.3 shall be provided in accordance with Table
F224.4.

Table F224.4--Guest Rooms With Communication Features
------------------------------------------------------------------------
Minimum number of required
Total number of guest rooms provided guest rooms with
communication features
------------------------------------------------------------------------
2 to 25................................... 2.
26 to 50.................................. 4.
51 to 75.................................. 7.
76 to 100................................. 9.
101 to 150................................ 12.
151 to 200................................ 14.
201 to 300................................ 17.
301 to 400................................ 20.
401 to 500................................ 22.
501 to 1000............................... 5 percent of total.
1001 and over............................. 50, plus 3 for each 100 over
1000.
------------------------------------------------------------------------

F224.5 Dispersion. Guest rooms required to provide mobility
features complying with 806.2 and guest rooms required to provide
communication features complying with 806.3 shall be dispersed among
the various classes of guest rooms, and shall provide choices of
types of guest rooms, number of beds, and other amenities comparable
to the choices provided to other guests. Where the minimum number of
guest rooms required to comply with 806 is not sufficient to allow
for complete dispersion, guest rooms shall be dispersed in the
following priority: guest room type, number of beds, and amenities.
At least one guest room required to provide mobility features
complying with 806.2 shall also provide communication features
complying with 806.3. Not more than 10 percent of guest rooms
required to provide mobility features complying with 806.2 shall be
used to satisfy the minimum number of guest rooms required to
provide communication features complying with 806.3.

F225 Storage

F225.1 General. Storage facilities shall comply with F225.
F225.2 Storage. Where storage is provided in accessible spaces,
at least one of each type shall comply with 811.
F225.2.1 Lockers. Where lockers are provided, at least 5
percent, but no fewer than one of each type, shall comply with 811.
F225.2.2 Self-Service Shelving. Self-service shelves shall be
located on an accessible route complying with 402. Self-service
shelving shall not be required to comply with 308.
F225.3 Self-Service Storage Facilities. Self-service storage
facilities shall provide individual self-service storage spaces
complying with these requirements in accordance with Table F225.3.

Table F225.3--Self-Service Storage Facilities
------------------------------------------------------------------------
Minimum number of spaces
Total spaces in facility required to be accessible
------------------------------------------------------------------------
1 to 200.................................. 5 percent, but no fewer than
1.
201 and over.............................. 10, plus 2 percent of total
number of units over 200.
------------------------------------------------------------------------

F225.3.1 Dispersion. Individual self-service storage spaces
shall be dispersed throughout the various classes of spaces
provided. Where more classes of spaces are provided than the number
required to be accessible, the number of spaces shall not be
required to exceed that required by Table F225.3. Self-service
storage spaces complying with Table F225.3 shall not be required to
be dispersed among buildings in a multi-building facility.

[[Page 59521]]

F226 Dining Surfaces and Work Surfaces

F226.1 General. Where dining surfaces are provided for the
consumption of food or drink, at least 5 percent of the seating
spaces and standing spaces at the dining surfaces shall comply with
902. In addition, where work surfaces are provided, at least 5
percent shall comply with 902.
EXCEPTIONS: 1. Sales counters and service counters shall not be
required to comply with 902.
2. Check writing surfaces provided at check-out aisles not
required to comply with 904.3 shall not be required to comply with
902.
F226.2 Dispersion. Dining surfaces and work surfaces required to
comply with 902 shall be dispersed throughout the space or facility
containing dining surfaces and work surfaces.

F227 Sales and Service

F227.1 General. Where provided, check-out aisles, sales
counters, service counters, food service lines, queues, and waiting
lines shall comply with F227 and 904.
F227.2 Check-Out Aisles. Where check-out aisles are provided,
check-out aisles complying with 904.3 shall be provided in
accordance with Table F227.2. Where check-out aisles serve different
functions, check-out aisles complying with 904.3 shall be provided
in accordance with Table F227.2 for each function. Where check-out
aisles are dispersed throughout the building or facility, check-out
aisles complying with 904.3 shall be dispersed.
EXCEPTION: Where the selling space is under 5000 square feet
(465 m2) no more than one check-out aisle complying with 904.3 shall
be required.

Table F227.2--Check-Out Aisles
------------------------------------------------------------------------
Minimum number of check-out
Number of check-out aisles of each aisles of each function
function required to comply with
904.3
------------------------------------------------------------------------
1 to 4.................................... 1.
5 to 8.................................... 2.
9 to 15................................... 3.
16 and over............................... 3, plus 20 percent of
additional aisles.
------------------------------------------------------------------------

F227.2.1 Altered Check-Out Aisles. Where check-out aisles are
altered, at least one of each check-out aisle serving each function
shall comply with 904.3 until the number of check-out aisles
complies with F227.2.
F227.3 Counters. Where provided, at least one of each type of
sales counter and service counter shall comply with 904.4. Where
counters are dispersed throughout the building or facility, counters
complying with 904.4 also shall be dispersed.
F227.4 Food Service Lines. Food service lines shall comply with
904.5. Where self-service shelves are provided, at least 50 percent,
but no fewer than one, of each type provided shall comply with 308.
F227.5 Queues and Waiting Lines. Queues and waiting lines
servicing counters or check-out aisles required to comply with 904.3
or 904.4 shall comply with 403.

F228 Depositories, Vending Machines, Change Machines, Mail Boxes, and
Fuel Dispensers

F228.1 General. Where provided, at least one of each type of
depository, vending machine, change machine, and fuel dispenser
shall comply with 309.
EXCEPTIONS: 1. Drive-up only depositories shall not be required
to comply with 309.
2. Fuel dispensers provided for fueling official government
vehicles shall not be required to comply with 309.
F228.2 Mail Boxes. Where mail boxes are provided in an interior
location, at least 5 percent, but no fewer than one, of each type
shall comply with 309. In residential facilities, where mail boxes
are provided for each residential dwelling unit, mail boxes
complying with 309 shall be provided for each residential dwelling
unit required to provide mobility features complying with 809.2
through 809.4.

F229 Windows

F229.1 General. Where glazed openings are provided in accessible
rooms or spaces for operation by occupants, excluding employees, at
least one opening shall comply with 309. In accessible rooms or
spaces, each glazed opening required by an administrative authority
to be operable shall comply with 309.
EXCEPTIONS: 1. Glazed openings in residential dwelling units
required to comply with 809 shall not be required to comply with
F229.
2. Glazed openings in guest rooms required to provide
communication features and in guest rooms required to comply with
F206.5.3 shall not be required to comply with F229.

F230 Two-Way Communication Systems

F230.1 General. Where a two-way communication system is provided
to gain admittance to a building or facility or to restricted areas
within a building or facility, the system shall comply with 708.

F231 Judicial Facilities

F231.1 General. Judicial facilities shall comply with F231.
F231.2 Courtrooms. Each courtroom shall comply with 808.
F231.3 Holding Cells. Where provided, central holding cells and
court-floor holding cells shall comply with F231.3.
F231.3.1 Central Holding Cells. Where separate central holding
cells are provided for adult male, juvenile male, adult female, or
juvenile female, one of each type shall comply with 807.2. Where
central holding cells are provided and are not separated by age or
sex, at least one cell complying with 807.2 shall be provided.
F231.3.2 Court-Floor Holding Cells. Where separate court-floor
holding cells are provided for adult male, juvenile male, adult
female, or juvenile female, each courtroom shall be served by one
cell of each type complying with 807.2. Where court-floor holding
cells are provided and are not separated by age or sex, courtrooms
shall be served by at least one cell complying with 807.2. Cells may
serve more than one courtroom.
F231.4 Visiting Areas. Visiting areas shall comply with F231.4.
F231.4.1 Cubicles and Counters. At least 5 percent, but no fewer
than one, of cubicles shall comply with 902 on both the visitor and
detainee sides. Where counters are provided, at least one shall
comply with 904.4.2 on both the visitor and detainee sides.
EXCEPTION: The detainee side of cubicles or counters at non-
contact visiting areas not serving holding cells required to comply
with F231 shall not be required to comply with 902 or 904.4.2.
F231.4.2 Partitions. Where solid partitions or security glazing
separate visitors from detainees at least one of each type of
cubicle or counter partition shall comply with 904.6.

F232 Detention Facilities and Correctional Facilities

F232.1 General. Buildings, facilities, or portions thereof, in
which people are detained for penal or correction purposes, or in
which the liberty of the inmates is restricted for security reasons
shall comply with F232.
F232.2 General Holding Cells and General Housing Cells. General
holding cells and general housing cells shall be provided in
accordance with F232.2.
EXCEPTION: Alterations to cells shall not be required to comply
except to the extent determined by regulations issued by the
appropriate Federal agency having authority under section 504 of the
Rehabilitation Act of 1973.
F232.2.1 Cells with Mobility Features. At least 2 percent, but
no fewer than one, of the total number of cells in a facility shall
provide mobility features complying with 807.2.
F232.2.1.1 Beds. In cells having more than 25 beds, at least 5
percent of the beds shall have clear floor space complying with
807.2.3.
F232.2.2 Cells with Communication Features. At least 2 percent,
but no fewer than one, of the total number of general holding cells
and general housing cells equipped with audible emergency alarm
systems and permanently installed telephones within the cell shall
provide communication features complying with 807.3.
F232.3 Special Holding Cells and Special Housing Cells. Where
special holding cells or special housing cells are provided, at
least one cell serving each purpose shall provide mobility features
complying with 807.2. Cells subject to this requirement include, but
are not limited to, those used for purposes of orientation,
protective custody, administrative or disciplinary detention or
segregation, detoxification, and medical isolation.
EXCEPTION: Alterations to cells shall not be required to comply
except to the extent determined by regulations issued by the
appropriate Federal agency having authority under section 504 of the
Rehabilitation Act of 1973.
F232.4 Medical Care Facilities. Patient bedrooms or cells
required to comply with F223 shall be provided in addition to any
medical isolation cells required to comply with F232.3.

[[Page 59522]]

F232.5 Visiting Areas. Visiting areas shall comply with F232.5.
F232.5.1 Cubicles and Counters. At least 5 percent, but no fewer
than one, of cubicles shall comply with 902 on both the visitor and
detainee sides. Where counters are provided, at least one shall
comply with 904.4.2 on both the visitor and detainee or inmate
sides.
EXCEPTION: The inmate or detainee side of cubicles or counters
at non-contact visiting areas not serving holding cells or housing
cells required to comply with F232 shall not be required to comply
with 902 or 904.4.2.
F232.5.2 Partitions. Where solid partitions or security glazing
separate visitors from detainees or inmates at least one of each
type of cubicle or counter partition shall comply with 904.6.

F233 Residential Facilities

F233.1 General. Facilities with residential dwelling units shall
comply with F233.
F233.2 Residential Dwelling Units Provided by HUD or Through
Grant or Loan Programs Administered by HUD. Where facilities with
residential dwelling units are provided by the Department of Housing
and Urban Development (HUD), or through a grant or loan program
administered by HUD, residential dwelling units with mobility
features complying with 809.2 through 809.4 shall be provided in a
number required by the regulations issued by HUD under Section 504
of the Rehabilitation Act of 1973, as amended. Residential dwelling
units required to provide mobility features complying with 809.2
through 809.4 shall be on an accessible route as required by F206.
In addition, residential dwelling units with communication features
complying with 809.5 shall be provided in a number required by the
applicable HUD regulations. Residential dwelling units subject to
F233.2 shall not be required to comply with F233.3 or F233.4.
F233.3 Residential Dwelling Units Provided on Military
Installations. Military installations with residential dwelling
units shall comply with F233.3. Residential dwelling units on
military installations subject to F233.3 shall not be required to
comply with F233.2 or F233.4.
F233.3.1 Minimum Number: New Construction. Newly constructed
facilities with residential dwelling units shall comply with
F233.3.1.
F233.3.1.1 Residential Dwelling Units with Mobility Features. On
military installations with residential dwelling units, at least 5
percent, but no fewer than one unit, of the total number of
residential dwelling units shall provide mobility features complying
with 809.2 through 809.4 and shall be on an accessible route as
required by F206.
F233.3.1.2 Residential Dwelling Units with Communication
Features. On military installations with residential dwelling units,
at least 2 percent, but no fewer than one unit, of the total number
of residential dwelling units shall provide communication features
complying with 809.5.
F233.3.2 Additions. Where an addition to an existing building
results in an increase in the number of residential dwelling units,
the requirements of F233.3.1 shall apply only to the residential
dwelling units that are added until the total number of residential
dwelling units complies with the minimum number required by
F233.3.1. Residential dwelling units required to comply with
F233.3.1.1 shall be on an accessible route as required by F206.
F233.3.3 Alterations. Alterations shall comply with F233.3.3.
EXCEPTION: Where compliance with 809.2, 809.3, or 809.4 is
technically infeasible, or where it is technically infeasible to
provide an accessible route to a residential dwelling unit, the
Department of Defense shall be permitted to alter or construct a
comparable residential dwelling unit to comply with 809.2 through
809.4 provided that the minimum number of residential dwelling units
required by F233.3.1.1 and F233.3.1.2, as applicable, is satisfied.
F233.3.3.1 Alterations to Vacated Buildings. Where a building is
vacated for the purposes of alteration, at least 5 percent of the
residential dwelling units shall comply with 809.2 through 809.4 and
shall be on an accessible route as required by F206. In addition, at
least 2 percent of the residential dwelling units shall comply with
809.5.
F233.3.3.2 Alterations to Individual Residential Dwelling Units.
In individual residential dwelling units, where a bathroom or a
kitchen is substantially altered, and at least one other room is
altered, the requirements of F233.3.1 shall apply to the altered
residential dwelling units until the total number of residential
dwelling units complies with the minimum number required by
F233.3.1.1 and F233.3.1.2. Residential dwelling units required to
comply with F233.3.1.1 shall be on an accessible route as required
by F206.
F233.3.4 Dispersion. Residential dwelling units required to
provide mobility features complying with 809.2 through 809.4 and
residential dwelling units required provide communication features
complying with 809.5 shall be dispersed among the various types of
residential dwelling units on the military installation, and shall
provide choices of residential dwelling units comparable to, and
integrated with, those available to other residents.
EXCEPTION: Where multi-story residential dwelling units are one
of the types of residential dwelling units provided, one-story
residential dwelling units shall be permitted as a substitute for
multi-story residential dwelling units where equivalent spaces and
amenities are provided in the one-story residential dwelling unit.
F233.4 Residential Dwelling Units Provided by Other Federal
Agencies or Through Grant or Loan Programs Administered by Other
Federal Agencies. Facilities with residential dwelling units
provided by other federal agencies or through grant or loan programs
administered by other federal agencies shall comply with F233.4.
Residential dwelling units subject to F233.4 shall not be required
to comply with F233.2 or F233.3.
F233.4.1 Minimum Number: New Construction. Newly constructed
facilities with residential dwelling units shall comply with
F233.4.1.
EXCEPTION: Where facilities contain 15 or fewer residential
dwelling units, the requirements of F233.4.1.1 and F233.4.1.2 shall
apply to the total number of residential dwelling units that are
constructed under a single contract, or are developed as a whole,
whether or not located on a common site.
F233.4.1.1 Residential Dwelling Units with Mobility Features. In
facilities with residential dwelling units, at least 5 percent, but
no fewer than one unit, of the total number of residential dwelling
units shall provide mobility features complying with 809.2 through
809.4 and shall be on an accessible route as required by F206.
F233.4.1.2 Residential Dwelling Units with Communication
Features. In facilities with residential dwelling units, at least 2
percent, but no fewer than one unit, of the total number of
residential dwelling units shall provide communication features
complying with 809.5.
F233.4.2 Residential Dwelling Units for Sale. Residential
dwelling units offered for sale shall provide accessible features to
the extent required by regulations issued by Federal agencies under
Section 504 of the Rehabilitation Act of 1973, as amended.
F233.4.3 Additions. Where an addition to an existing building
results in an increase in the number of residential dwelling units,
the requirements of F233.4.1 shall apply only to the residential
dwelling units that are added until the total number of residential
dwelling units complies with the minimum number required by
F233.4.1. Residential dwelling units required to comply with
F233.4.1.1 shall be on an accessible route as required by F206.
F233.4.4 Alterations. Alterations shall comply with F233.4.4.
EXCEPTION: Where compliance with 809.2, 809.3, or 809.4 is
technically infeasible, or where it is technically infeasible to
provide an accessible route to a residential dwelling unit, the
entity shall be permitted to alter or construct a comparable
residential dwelling unit to comply with 809.2 through 809.4
provided that the minimum number of residential dwelling units
required by F233.4.1.1 and F233.4.1.2, as applicable, is satisfied.
F233.4.4.1 Alterations to Vacated Buildings. Where a building is
vacated for the purposes of alteration and the altered building
contains more than 15 residential dwelling units, at least 5 percent
of the residential dwelling units shall comply with 809.2 through
809.4 and shall be on an accessible route as required by F206. In
addition, at least 2 percent of the residential dwelling units shall
comply with 809.5.
F233.4.4.2 Alterations to Individual Residential Dwelling Units.
In individual residential dwelling units, where a bathroom or a
kitchen is substantially altered, and at least one other room is
altered the requirements of F233.4.1 shall apply to the altered
residential dwelling units until the total number of residential
dwelling units complies with the minimum number required by
F233.4.1.1 and F233.4.1.2. Residential dwelling units required to
comply with F233.4.1.1 shall be on an accessible route as required
by F206.
EXCEPTION: Where facilities contain 15 or fewer residential
dwelling units, the

[[Page 59523]]

requirements of F233.4.1.1 and F233.4.1.2 shall apply to the total
number of residential dwelling units that are altered under a single
contract, or are developed as a whole, whether or not located on a
common site.
F233.4.5 Dispersion. Residential dwelling units required to
provide mobility features complying with 809.2 through 809.4 and
residential dwelling units required to provide communication
features complying with 809.5 shall be dispersed among the various
types of residential dwelling units in the facility and shall
provide choices of residential dwelling units comparable to, and
integrated with, those available to other residents.
EXCEPTION: Where multi-story residential dwelling units are one
of the types of residential dwelling units provided, one-story
residential dwelling units shall be permitted as a substitute for
multi-story residential dwelling units where equivalent spaces and
amenities are provided in the one-story residential dwelling unit.

F234 Amusement Rides

F234.1 General. Amusement rides shall comply with F234.
EXCEPTION: Mobile or portable amusement rides shall not be
required to comply with F234.
F234.2 Load and Unload Areas. Load and unload areas serving
amusement rides shall comply with 1002.3.
F234.3 Minimum Number. Amusement rides shall provide at least
one wheelchair space complying with 1002.4, or at least one
amusement ride seat designed for transfer complying with 1002.5, or
at least one transfer device complying with 1002.6.
EXCEPTIONS: 1. Amusement rides that are controlled or operated
by the rider shall not be required to comply with F234.3.
2. Amusement rides designed primarily for children, where
children are assisted on and off the ride by an adult, shall not be
required to comply with F234.3.
3. Amusement rides that do not provide amusement ride seats
shall not be required to comply with F234.3.
F234.4 Existing Amusement Rides. Where existing amusement rides
are altered, the alteration shall comply with F234.4.
F234.4.1 Load and Unload Areas. Where load and unload areas
serving existing amusement rides are newly designed and constructed,
the load and unload areas shall comply with 1002.3.
F234.4.2 Minimum Number. Where the structural or operational
characteristics of an amusement ride are altered to the extent that
the amusement ride's performance differs from that specified by the
manufacturer or the original design, the amusement ride shall comply
with F234.3.

F235 Recreational Boating Facilities

F235.1 General. Recreational boating facilities shall comply
with F235.
F235.2 Boat Slips. Boat slips complying with 1003.3.1 shall be
provided in accordance with Table F235.2. Where the number of boat
slips is not identified, each 40 feet (12 m) of boat slip edge
provided along the perimeter of the pier shall be counted as one
boat slip for the purpose of this section.

Table F235.2--Boat Slips
------------------------------------------------------------------------
Total number of boat slips provided in Minimum number of required
facility accessible boat slips
------------------------------------------------------------------------
1 to 25................................... 1.
26 to 50.................................. 2.
51 to 100................................. 3.
101 to 150................................ 4.
151 to 300................................ 5.
301 to 400................................ 6.
401 to 500................................ 7.
501 to 600................................ 8.
601 to 700................................ 9.
701 to 800................................ 10.
801 to 900................................ 11.
901 to 1000............................... 12.
1001 and over............................. 12, plus 1 for every 100, or
fraction thereof, over
1000.
------------------------------------------------------------------------

F235.2.1 Dispersion. Boat slips complying with 1003.3.1 shall be
dispersed throughout the various types of boat slips provided. Where
the minimum number of boat slips required to comply with 1003.3.1
has been met, no further dispersion shall be required.
F235.3 Boarding Piers at Boat Launch Ramps. Where boarding piers
are provided at boat launch ramps, at least 5 percent, but no fewer
than one, of the boarding piers shall comply with 1003.3.2.

F236 Exercise Machines and Equipment

F236.1 General. At least one of each type of exercise machine
and equipment shall comply with 1004.

F237 Fishing Piers and Platforms

F237.1 General. Fishing piers and platforms shall comply with
1005.

F238 Golf Facilities

F238.1 General. Golf facilities shall comply with F238.
F238.2 Golf Courses. Golf courses shall comply with F238.2.
F238.2.1 Teeing Grounds. Where one teeing ground is provided for
a hole, the teeing ground shall be designed and constructed so that
a golf car can enter and exit the teeing ground. Where two teeing
grounds are provided for a hole, the forward teeing ground shall be
designed and constructed so that a golf car can enter and exit the
teeing ground. Where three or more teeing grounds are provided for a
hole, at least two teeing grounds, including the forward teeing
ground, shall be designed and constructed so that a golf car can
enter and exit each teeing ground.
EXCEPTION: In existing golf courses, the forward teeing ground
shall not be required to be one of the teeing grounds on a hole
designed and constructed so that a golf car can enter and exit the
teeing ground where compliance is not feasible due to terrain.
F238.2.2 Putting Greens. Putting greens shall be designed and
constructed so that a golf car can enter and exit the putting green.
F238.2.3 Weather Shelters. Where provided, weather shelters
shall be designed and constructed so that a golf car can enter and
exit the weather shelter and shall comply with 1006.4.
F238.3 Practice Putting Greens, Practice Teeing Grounds, and
Teeing Stations at Driving Ranges. At least 5 percent, but no fewer
than one, of practice putting greens, practice teeing grounds, and
teeing stations at driving ranges shall be designed and constructed
so that a golf car can enter and exit the practice putting greens,
practice teeing grounds, and teeing stations at driving ranges.

F239 Miniature Golf Facilities

F239.1 General. Miniature golf facilities shall comply with
F239.
F239.2 Minimum Number. At least 50 percent of holes on miniature
golf courses shall comply with 1007.3.
F239.3 Miniature Golf Course Configuration. Miniature golf
courses shall be configured so that the holes complying with 1007.3
are consecutive. Miniature golf courses shall provide an accessible
route from the last hole complying with 1007.3 to the course
entrance or exit without requiring travel through any other holes on
the course.
EXCEPTION: One break in the sequence of consecutive holes shall
be permitted provided that the last hole on the miniature golf
course is the last hole in the sequence.

F240 Play Areas

F240.1 General. Play areas for children ages 2 and over shall
comply with F240. Where separate play areas are provided within a
site for specific age groups, each play area shall comply with F240.
EXCEPTIONS: 1. Play areas located in family child care
facilities where the proprietor actually resides shall not be
required to comply with F240.
2. In existing play areas, where play components are relocated
for the purposes of creating safe use zones and the ground surface
is not altered or extended for more than one use zone, the play area
shall not be required to comply with F240.
3. Amusement attractions shall not be required to comply with
F240.
4. Where play components are altered and the ground surface is
not altered, the ground surface shall not be required to comply with
1008.2.6 unless required by F202.4.
F240.1.1 Additions. Where play areas are designed and
constructed in phases, the requirements of F240 shall apply to each
successive addition so that when the addition is completed, the
entire play area complies with all the applicable requirements of
F240.
F240.2 Play Components. Where provided, play components shall
comply with F240.2.
F240.2.1 Ground Level Play Components. Ground level play
components shall be provided in the number and types required by
F240.2.1. Ground level play components that are provided to comply
with F240.2.1.1 shall be permitted to satisfy the additional number
required by F240.2.1.2 if the minimum required types of play
components are satisfied. Where two or more required ground level
play components are provided, they shall be dispersed throughout the
play area and integrated with other play components.
F240.2.1.1 Minimum Number and Types. Where ground level play
components are

[[Page 59524]]

provided, at least one of each type shall be on an accessible route
and shall comply with 1008.4.
F240.2.1.2 Additional Number and Types. Where elevated play
components are provided, ground level play components shall be
provided in accordance with Table F240.2.1.2 and shall comply with
1008.4.
EXCEPTION: If at least 50 percent of the elevated play
components are connected by a ramp and at least 3 of the elevated
play components connected by the ramp are different types of play
components, the play area shall not be required to comply with
F240.2.1.2.

Table F240.2.1.2--Number and Types of Ground Level Play Components
Required To Be on Accessible Routes
------------------------------------------------------------------------
Minimum number of
Minimum number of different types of
Number of elevated play ground level play ground level play
components provided components required components required
to be on an to be on an
accessible route accessible route
------------------------------------------------------------------------
1........................... Not applicable...... Not applicable.
2 to 4...................... 1................... 1.
5 to 7...................... 2................... 2.
8 to 10..................... 3................... 3.
11 to 13.................... 4................... 3.
14 to 16.................... 5................... 3.
17 to 19.................... 6................... 3.
20 to 22.................... 7................... 4.
23 to 25.................... 8................... 4.
26 and over................. 8, plus 1 for each 5.
additional 3, or
fraction thereof,
over 25.
------------------------------------------------------------------------

F240.2.2 Elevated Play Components. Where elevated play
components are provided, at least 50 percent shall be on an
accessible route and shall comply with 1008.4.

F241 Saunas and Steam Rooms

F241.1 General. Where provided, saunas and steam rooms shall
comply with 612.
EXCEPTION: Where saunas or steam rooms are clustered at a single
location, no more than 5 percent of the saunas and steam rooms, but
no fewer than one, of each type in each cluster shall be required to
comply with 612.

F242 Swimming Pools, Wading Pools, and Spas

F242.1 General. Swimming pools, wading pools, and spas shall
comply with F242.
F242.2 Swimming Pools. At least two accessible means of entry
shall be provided for swimming pools. Accessible means of entry
shall be swimming pool lifts complying with 1009.2; sloped entries
complying with 1009.3; transfer walls complying with 1009.4;
transfer systems complying with 1009.5; and pool stairs complying
with 1009.6. At least one accessible means of entry provided shall
comply with 1009.2 or 1009.3.
EXCEPTIONS: 1. Where a swimming pool has less than 300 linear
feet (91 m) of swimming pool wall, no more than one accessible means
of entry shall be required provided that the accessible means of
entry is a swimming pool lift complying with 1009.2 or sloped entry
complying with 1009.3.
2. Wave action pools, leisure rivers, sand bottom pools, and
other pools where user access is limited to one area shall not be
required to provide more than one accessible means of entry provided
that the accessible means of entry is a swimming pool lift complying
with 1009.2, a sloped entry complying with 1009.3, or a transfer
system complying with 1009.5.
3. Catch pools shall not be required to provide an accessible
means of entry provided that the catch pool edge is on an accessible
route.
F242.3 Wading Pools. At least one accessible means of entry
shall be provided for wading pools. Accessible means of entry shall
comply with sloped entries complying with 1009.3.
F242.4 Spas. At least one accessible means of entry shall be
provided for spas. Accessible means of entry shall comply with
swimming pool lifts complying with 1009.2; transfer walls complying
with 1009.4; or transfer systems complying with 1009.5.
EXCEPTION: Where spas are provided in a cluster, no more than 5
percent, but no fewer than one, spa in each cluster shall be
required to comply with F242.4.

F243 Shooting Facilities With Firing Positions

F243.1 General. Where shooting facilities with firing positions
are designed and constructed at a site, at least 5 percent, but no
fewer than one, of each type of firing position shall comply with
1010.

F244 Camping Facilities

F244.1 General. Camping facilities, other than camping
facilities on trails, shall comply with F244.
F244.2 Camping Units with Mobility Features. Camping facilities
shall provide camping units with mobility features complying with
F244.2 in accordance with Table F244.2. Where a camping facility
provides different types of camping units, Table F244.2 shall apply
to each type of camping unit provided.

Table F244.2--Camping Units With Mobility Features
------------------------------------------------------------------------
Minimum number of camping
Total number of camping units provided in units with mobility features
camping facility required
------------------------------------------------------------------------
1......................................... 1.
2 to 25................................... 2.
26 to 50.................................. 3.
51 to 75.................................. 4.
76 to 100................................. 5.
101 to 150................................ 7.
151 to 200................................ 8.
201 and over.............................. 8, plus 2 percent of the
number over 200.
------------------------------------------------------------------------

F244.2.1 Alterations and Additions. Where camping units are
altered or added, the requirements of F244.2 shall apply only to the
camping units that are altered or added until the number of camping
units with mobility features complies with the minimum number
required in Table 244.2.
EXCEPTION: Where an entity is implementing a transition plan for
program accessibility developed pursuant to regulations issued under
section 504 of the Rehabilitation Act that designates specific
camping units to provide mobility features complying with F244.2,
the entity shall not be required to comply with F244.2 when altering
individual elements within camping units that are not designated to
provide mobility features complying with F244.2.
F244.2.2 Dispersion. Camping units required to provide mobility
features complying with F244.2 shall provide choices of camping
units comparable to, and integrated with, those available to others.
F244.2.3 Elements Within Camping Units with Mobility Features.
Elements within camping units required to provide mobility features
shall comply with F244.2.3.
F244.2.3.1 Outdoor Constructed Features. Where provided, at
least one of each type of outdoor constructed features shall comply
with 1011. Where more than one of the same type of outdoor
constructed features is provided, at least two of the same type of

[[Page 59525]]

outdoor constructed features shall comply with 1011.
F244.2.3.2 Parking Spaces. Where provided, parking spaces shall
comply with F244.2.3.2.
F244.2.3.2.1 Recreational Vehicles. Where parking spaces are
provided for recreational vehicles, at least one parking space shall
comply with 1012.2, 1012.4, and 1012.5. Where more than one parking
space is provided for recreational vehicles, at least two parking
spaces shall comply with 1012.2, 1012.4, and 1012.5.
F244.2.3.2.2 Vehicles Other Than Recreational Vehicles. Where
parking spaces are provided for vehicles other than recreational
vehicles, at least one parking space shall comply with 1012.3,
1012.4, and 1012.5. Where more than one parking space is provided
for a vehicle other than a recreational vehicle, at least two
parking spaces shall comply with 1012.3, 1012.4, and 1012.5.
244.2.3.3 Tent Pads and Tent Platforms. Where provided, at least
one tent pad and tent platform shall comply with 1013. Where more
than one tent pad and tent platform is provided, at least two tent
pads and tent platforms shall comply with 1013.
F244.2.3.4 Camp Shelters. Where provided, at least one camp
shelter shall comply with 1014. Where more than one camp shelter is
provided, at least two camp shelters shall comply with 1014.
F244.3 Outdoor Constructed Features in Common Use and Public Use
Areas. Where provided in common use and public use areas that serve
camping units with mobility features, at least 20 percent, but not
less than one, of each type of outdoor constructed feature provided
at each location shall comply with 1011.
F244.4 Pull-up Spaces for Recreational Vehicles at Dump
Stations. Where provided, pull-up spaces for recreational vehicles
at dump stations shall comply with 1012.2, 1012.4, and 1012.5.
F244.5 Outdoor Recreation Access Routes. Camping facilities
shall provide outdoor recreation access routes complying with 1016
in accordance with F244.5.
F244.5.1 Routes Within Camping Units with Mobility Features. At
least one outdoor recreation access route shall connect accessible
elements, spaces, and facilities provided within camping units with
mobility features.
F244.5.2 Routes to and Within Common Use and Public Use Areas.
Common use and public use areas serving camping units with mobility
features shall provide outdoor recreation access routes in
accordance with F244.5.2.
EXCEPTION: Outdoor recreation access routes shall not be
required to connect camping units with mobility features and
recreational vehicle dump stations where a pull-up space complying
with 1012.2, 1012.4, and 1012.5 is provided at the dump station for
recreational vehicles.
F244.5.2.1 Routes to Common Use and Public Use Areas. At least
one outdoor recreation access route shall connect each camping unit
with mobility features with common use and public use areas serving
the unit.
F244.5.2.2 Routes Within Common Use and Public Use Areas. At
least one outdoor recreation access route shall connect accessible
elements, spaces, and facilities provided within common use and
public use areas serving camping units with mobility features.
F244.5.3 Routes to Adjacent Recreation Facilities. Where a
circulation path connects camping facilities and adjacent recreation
facilities, at least one outdoor recreation access route shall
connect camping units with mobility features to an accessible route
serving the adjacent recreation facilities.
F244.5.4 Location. Outdoor recreation access routes required by
F244.5.2 and F244.5.3 shall coincide with or be located in the same
area as general circulation paths.

F245 Picnic Facilities

F245.1 General. Picnic facilities, other than picnic facilities
on trails, shall comply with F245.
F245.2 Picnic Units with Mobility Features. Picnic facilities
shall provide picnic units with mobility features in accordance with
F245.2.
F245.2.1 Picnic Facilities with Two or Fewer Picnic Units. Where
picnic facilities contain two or fewer picnic units, each picnic
unit shall provide mobility features complying with F245.2.
F245.2.2 Picnic Facilities with More Than Two Picnic Units.
Where picnic facilities contain more than two picnic units, at least
20 percent, but not less than two, of the picnic units shall provide
mobility features complying with F245.2.
F245.2.3 Alterations and Additions. Where picnic units are
altered or added, the requirements of F245.2 shall apply only to the
picnic units that are altered or added until the number of picnic
units with mobility features complies with the minimum number
required in F245.2.1 or F245.2.2.
EXCEPTION: Where an entity is implementing a transition plan for
program accessibility developed pursuant to regulations issued under
section 504 of the Rehabilitation Act that designates specific
picnic units to provide mobility features complying with F245.2, the
entity shall not be required to comply with F245.2 when altering
individual elements within picnic units that are not designated to
provide mobility features complying with F245.2.
F245.2.4 Dispersion. Picnic units required to provide mobility
features complying with F245.2 shall provide choices of picnic units
comparable to, and integrated with, those available to others.
F245.2.5 Elements Within Picnic Units with Mobility Features.
Elements within picnic units required to provide mobility features
shall comply with F245.2.5.
F245.2.5.1 Outdoor Constructed Features. Where provided, at
least one of each type of outdoor constructed feature shall comply
with 1011. Where more than one of the same type of outdoor
constructed feature is provided, at least two of the same type of
outdoor constructed features shall comply with 1011.
F245.2.5.2 Parking Spaces. Where provided, at least one parking
space shall comply with 1012.3, 1012.4, and 1012.5. Where more than
one parking space is provided, at least two parking spaces shall
comply with 1012.3, 1012.4, and 1012.5.
F245.3 Outdoor Constructed Features in Common Use and Public Use
Areas. Where provided in common use and public use areas that serve
picnic units with mobility features, at least 20 percent, but not
less than one, of each type of outdoor constructed feature provided
at each location shall comply with 1011.
F245.4 Outdoor Recreation Access Routes. Picnic facilities shall
provide outdoor recreation access routes complying with 1016 in
accordance with F245.4.
F245.4.1 Routes Within Picnic Units with Mobility Features. At
least one outdoor recreation access route shall connect accessible
elements, spaces, and facilities provided within picnic units with
mobility features.
F245.4.2 Routes to and Within Common Use and Public Use Areas.
Common use and public use areas serving picnic units with mobility
features shall provide outdoor recreation access routes in
accordance with F245.4.2.
F245.4.2.1 Routes to Common Use and Public Use Areas. At least
one outdoor recreation access route shall connect each picnic unit
with mobility features with common use and public use areas serving
that unit.
F245.4.2.2 Routes Within Common Use and Public Use Areas. At
least one outdoor recreation access route shall connect accessible
elements, spaces, and facilities provided within common use and
public use areas serving picnic units with mobility features.
F245.4.3 Routes to Adjacent Recreation Facilities. Where a
circulation path connects picnic facilities and adjacent recreation
facilities, at least one outdoor recreation access route shall
connect picnic units with mobility features to an accessible route
serving the adjacent recreation facilities.
F245.4.4 Location. Outdoor recreation access routes required by
F245.4.2 and F245.4.3 shall coincide with or be located in the same
area as general circulation paths.

F246 Viewing Areas

F246.1 General. Viewing areas, other than viewing areas on
trails, shall comply with F246.1.
F246.2 Distinct Viewing Locations. Each distinct viewing
location within a viewing area shall comply with 1015.
F246.3 Outdoor Constructed Features. Where provided within
viewing areas, at least 20 percent, but not less than one, of each
type of outdoor constructed feature shall comply with 1011.
F246.4 Outdoor Recreation Access Routes. At least one outdoor
recreation access route complying with 1016 shall connect accessible
parking spaces or other arrival points serving the viewing area with
accessible elements, spaces, and facilities provided within the
viewing area.

F247 Trails

F247.1 General. Where a trail is designed for use by hikers or
pedestrians and directly

[[Page 59526]]

connects to a trailhead or another trail that substantially meets
the requirements in 1017, the trail shall comply with 1017.
F247.2 Existing Trails. Where the original design, function, or
purpose of an existing trail is changed and the altered portion of
the trail directly connects to a trailhead or another trail that
substantially meets the requirements in 1017, the altered portion of
the trail shall comply with 1017.
F247.3 Trailheads. Trailheads shall comply with F247.3.
F247.3.1 Outdoor Constructed Features. Where provided within
trailheads, at least 20 percent, but not less than one, of each type
of outdoor constructed feature shall comply with 1011.
F247.3.2 Outdoor Recreation Access Routes. At least one outdoor
recreation access route complying with 1016 shall connect the
following:
1. Accessible parking spaces or other arrival points serving the
trailhead;
2. Starting point of the trail; and
3. Accessible elements, spaces, and facilities provided within
the trailhead.
F247.4 Trail Facilities. Where provided on trails, facilities
shall comply with F247.4.
F247.4.1 Camping Facilities. Camping facilities provided on
trails shall comply with F244.2 and F244.3.
F247.4.2 Picnic Facilities. Picnic facilities provided on trails
shall comply with F245.2 and F245.3.
F247.4.3 Viewing Areas. Viewing areas provided on trails shall
comply with F246.2 and F246.3.
F247.4.4 Routes. Routes that connect trails complying with 1017
to camping facilities, picnic facilities, viewing areas, pit
toilets, and accessible elements provided within the facilities
shall comply with 1017.
F247.5 Outdoor Constructed Features. Where outdoor constructed
features are provided on trails, other than within facilities
specified in F247.4, at least 20 percent, but not less than one, of
each type of outdoor constructed feature at each location shall
comply with 1011.

F248 Beach Access Routes

F248.1 General. Beach access routes complying with 1018 shall be
provided in accordance with F248.1. Beach access routes shall be
permanent or removable.
EXCEPTION: Beach access routes shall not be required where
pedestrian access to the beach is not permitted.
F248.1.1 Facilities Serving Beaches. Beach access routes shall
be provided in a number complying with F248.2 where the entity that
administers or manages a beach constructs or alters any of the
following facilities to serve the beach:
1. Circulation paths;
2. Parking facilities;
3. Toilet facilities; or
4. Bathing facilities.
EXCEPTION: The entity shall not be required to expend more than
20 percent of the costs of constructing or altering the facilities
to provide beach access routes.
F248.1.2 Beach Nourishment. Beach access routes shall be
provided in a number complying with F248.2 where the entity that
administers or manages a beach undertakes a beach nourishment
project.
EXCEPTION: The entity shall not be required to expend more than
20 percent of the costs of a beach nourishment project to provide
beach access routes.
F248.2 Minimum Number. Where beach access routes are required by
F248.1, at least one beach access route shall be provided for each
1/2 mile (0.8 km) of beach shoreline administered or managed by the
entity.
EXCEPTION: The number of beach access routes shall not be
required to exceed the number of pedestrian access points provided
by the entity to a beach.
F248.3 Location. Beach access routes shall coincide with or be
located in the same area as pedestrian access points to the beach.

0
7. Revise Appendix D to this part to read as follows:

Appendix D to Part 1191--Technical

Chapter 3: Building Blocks

301 General

301.1 Scope. The provisions of Chapter 3 shall apply where
required by Chapter 2 or where referenced by a requirement in this
document.

302 Floor or Ground Surfaces

302.1 General. Floor and ground surfaces shall be stable, firm,
and slip resistant and shall comply with 302.
EXCEPTIONS: 1. Within animal containment areas, floor and ground
surfaces shall not be required to be stable, firm, and slip
resistant.
2. Areas of sport activity shall not be required to comply with
302.
302.2 Carpet. Carpet or carpet tile shall be securely attached
and shall have a firm cushion, pad, or backing or no cushion or pad.
Carpet or carpet tile shall have a level loop, textured loop, level
cut pile, or level cut/uncut pile texture. Pile height shall be \1/
2\ inch (13 mm) maximum. Exposed edges of carpet shall be fastened
to floor surfaces and shall have trim on the entire length of the
exposed edge. Carpet edge trim shall comply with 303.
302.3 Openings. Openings in floor or ground surfaces shall not
allow passage of a sphere more than \1/2\ inch (13 mm) diameter
except as allowed in 407.4.3, 409.4.3, 410.4, 810.5.3 and 810.10.
Elongated openings shall be placed so that the long dimension is
perpendicular to the dominant direction of travel.

303 Changes in Level

303.1 General. Where changes in level are permitted in floor or
ground surfaces, they shall comply with 303.
EXCEPTIONS: 1. Animal containment areas shall not be required to
comply with 303.
2. Areas of sport activity shall not be required to comply with
303.
303.2 Vertical. Changes in level of \1/4\ inch (6.4 mm) high
maximum shall be permitted to be vertical.
303.3 Beveled. Changes in level between \1/4\ inch (6.4 mm) high
minimum and \1/2\ inch (13 mm) high maximum shall be beveled with a
slope not steeper than 1:2.
303.4 Ramps. Changes in level greater than \1/2\ inch (13 mm)
high shall be ramped, and shall comply with 405 or 406.

304 Turning Space

304.1 General. Turning space shall comply with 304.
304.2 Floor or Ground Surfaces. Floor or ground surfaces of a
turning space shall comply with 302. Changes in level are not
permitted.
EXCEPTION: Slopes not steeper than 1:48 shall be permitted.
304.3 Size. Turning space shall comply with 304.3.1 or 304.3.2.
304.3.1 Circular Space. The turning space shall be a space of 60
inches (1525 mm) diameter minimum. The space shall be permitted to
include knee and toe clearance complying with 306.
304.3.2 T-Shaped Space. The turning space shall be a T-shaped
space within a 60 inch (1525 mm) square minimum with arms and base
36 inches (915 mm) wide minimum. Each arm of the T shall be clear of
obstructions 12 inches (305 mm) minimum in each direction and the
base shall be clear of obstructions 24 inches (610 mm) minimum. The
space shall be permitted to include knee and toe clearance complying
with 306 only at the end of either the base or one arm.
304.4 Door Swing. Doors shall be permitted to swing into turning
spaces.

305 Clear Floor or Ground Space

305.1 General. Clear floor or ground space shall comply with
305.
305.2 Floor or Ground Surfaces. Floor or ground surfaces of a
clear floor or ground space shall comply with 302. Changes in level
are not permitted.
EXCEPTION: Slopes not steeper than 1:48 shall be permitted.
305.3 Size. The clear floor or ground space shall be 30 inches
(760 mm) minimum by 48 inches (1220 mm) minimum.
305.4 Knee and Toe Clearance. Unless otherwise specified, clear
floor or ground space shall be permitted to include knee and toe
clearance complying with 306.
305.5 Position. Unless otherwise specified, clear floor or
ground space shall be positioned for either forward or parallel
approach to an element.
305.6 Approach. One full unobstructed side of the clear floor or
ground space shall adjoin an accessible route or adjoin another
clear floor or ground space.
305.7 Maneuvering Clearance. Where a clear floor or ground space
is located in an alcove or otherwise confined on all or part of
three sides, additional maneuvering clearance shall be provided in
accordance with 305.7.1 and 305.7.2.
305.7.1 Forward Approach. Alcoves shall be 36 inches (915 mm)
wide minimum where the depth exceeds 24 inches (610 mm).
305.7.2 Parallel Approach. Alcoves shall be 60 inches (1525 mm)
wide minimum where the depth exceeds 15 inches (380 mm).

306 Knee and Toe Clearance

306.1 General. Where space beneath an element is included as
part of clear floor or ground space or turning space, the space
shall comply with 306. Additional space

[[Page 59527]]

shall not be prohibited beneath an element but shall not be
considered as part of the clear floor or ground space or turning
space.
306.2 Toe Clearance.
306.2.1 General. Space under an element between the finish floor
or ground and 9 inches (230 mm) above the finish floor or ground
shall be considered toe clearance and shall comply with 306.2.
306.2.2 Maximum Depth. Toe clearance shall extend 25 inches (635
mm) maximum under an element.
306.2.3 Minimum Required Depth. Where toe clearance is required
at an element as part of a clear floor space, the toe clearance
shall extend 17 inches (430 mm) minimum under the element.
306.2.4 Additional Clearance. Space extending greater than 6
inches (150 mm) beyond the available knee clearance at 9 inches (230
mm) above the finish floor or ground shall not be considered toe
clearance.
306.2.5 Width. Toe clearance shall be 30 inches (760 mm) wide
minimum.
306.3 Knee Clearance.
306.3.1 General. Space under an element between 9 inches (230
mm) and 27 inches (685 mm) above the finish floor or ground shall be
considered knee clearance and shall comply with 306.3.
306.3.2 Maximum Depth. Knee clearance shall extend 25 inches
(635 mm) maximum under an element at 9 inches (230 mm) above the
finish floor or ground.
306.3.3 Minimum Required Depth. Where knee clearance is required
under an element as part of a clear floor space, the knee clearance
shall be 11 inches (280 mm) deep minimum at 9 inches (230 mm) above
the finish floor or ground, and 8 inches (205 mm) deep minimum at 27
inches (685 mm) above the finish floor or ground.
306.3.4 Clearance Reduction. Between 9 inches (230 mm) and 27
inches (685 mm) above the finish floor or ground, the knee clearance
shall be permitted to reduce at a rate of 1 inch (25 mm) in depth
for each 6 inches (150 mm) in height.
306.3.5 Width. Knee clearance shall be 30 inches (760 mm) wide
minimum.

307 Protruding Objects

307.1 General. Protruding objects shall comply with 307.
307.2 Protrusion Limits. Objects with leading edges more than 27
inches (685 mm) and not more than 80 inches (2030 mm) above the
finish floor or ground shall protrude 4 inches (100 mm) maximum
horizontally into the circulation path.
EXCEPTION: Handrails shall be permitted to protrude 4\1/2\
inches (115 mm) maximum.
307.3 Post-Mounted Objects. Freestanding objects mounted on
posts or pylons shall overhang circulation paths 12 inches (305 mm)
maximum when located 27 inches (685 mm) minimum and 80 inches (2030
mm) maximum above the finish floor or ground. Where a sign or other
obstruction is mounted between posts or pylons and the clear
distance between the posts or pylons is greater than 12 inches (305
mm), the lowest edge of such sign or obstruction shall be 27 inches
(685 mm) maximum or 80 inches (2030 mm) minimum above the finish
floor or ground.
EXCEPTION: The sloping portions of handrails serving stairs and
ramps shall not be required to comply with 307.3.
307.4 Vertical Clearance. Vertical clearance shall be 80 inches
(2030 mm) high minimum. Guardrails or other barriers shall be
provided where the vertical clearance is less than 80 inches (2030
mm) high. The leading edge of such guardrail or barrier shall be
located 27 inches (685 mm) maximum above the finish floor or ground.
EXCEPTION: Door closers and door stops shall be permitted to be
78 inches (1980 mm) minimum above the finish floor or ground.
307.5 Required Clear Width. Protruding objects shall not reduce
the clear width required for accessible routes.

308 Reach Ranges

308.1 General. Reach ranges shall comply with 308.
308.2 Forward Reach.
308.2.1 Unobstructed. Where a forward reach is unobstructed, the
high forward reach shall be 48 inches (1220 mm) maximum and the low
forward reach shall be 15 inches (380 mm) minimum above the finish
floor or ground.
308.2.2 Obstructed High Reach. Where a high forward reach is
over an obstruction, the clear floor space shall extend beneath the
element for a distance not less than the required reach depth over
the obstruction. The high forward reach shall be 48 inches (1220 mm)
maximum where the reach depth is 20 inches (510 mm) maximum. Where
the reach depth exceeds 20 inches (510 mm), the high forward reach
shall be 44 inches (1120 mm) maximum and the reach depth shall be 25
inches (635 mm) maximum.
308.3 Side Reach.
308.3.1 Unobstructed. Where a clear floor or ground space allows
a parallel approach to an element and the side reach is
unobstructed, the high side reach shall be 48 inches (1220 mm)
maximum and the low side reach shall be 15 inches (380 mm) minimum
above the finish floor or ground.
EXCEPTIONS: 1. An obstruction shall be permitted between the
clear floor or ground space and the element where the depth of the
obstruction is 10 inches (255 mm) maximum.
2. Operable parts of fuel dispensers shall be permitted to be 54
inches (1370 mm) maximum measured from the surface of the vehicular
way where fuel dispensers are installed on existing curbs.
308.3.2 Obstructed High Reach. Where a clear floor or ground
space allows a parallel approach to an element and the high side
reach is over an obstruction, the height of the obstruction shall be
34 inches (865 mm) maximum and the depth of the obstruction shall be
24 inches (610 mm) maximum. The high side reach shall be 48 inches
(1220 mm) maximum for a reach depth of 10 inches (255 mm) maximum.
Where the reach depth exceeds 10 inches (255 mm), the high side
reach shall be 46 inches (1170 mm) maximum for a reach depth of 24
inches (610 mm) maximum.
EXCEPTIONS: 1. The top of washing machines and clothes dryers
shall be permitted to be 36 inches (915 mm) maximum above the finish
floor.
2. Operable parts of fuel dispensers shall be permitted to be 54
inches (1370 mm) maximum measured from the surface of the vehicular
way where fuel dispensers are installed on existing curbs.

309 Operable Parts

309.1 General. Operable parts shall comply with 309.
309.2 Clear Floor Space. A clear floor or ground space complying
with 305 shall be provided.
309.3 Height. Operable parts shall be placed within one or more
of the reach ranges specified in 308.
309.4 Operation. Operable parts shall be operable with one hand
and shall not require tight grasping, pinching, or twisting of the
wrist. The force required to activate operable parts shall be 5
pounds (22.2 N) maximum.
EXCEPTION: Gas pump nozzles shall not be required to provide
operable parts that have an activating force of 5 pounds (22.2 N)
maximum.

Chapter 4: Accessible Routes

401 General

401.1 Scope. The provisions of Chapter 4 shall apply where
required by Chapter 2 or where referenced by a requirement in this
document.

402 Accessible Routes

402.1 General. Accessible routes shall comply with 402.
402.2 Components. Accessible routes shall consist of one or more
of the following components: walking surfaces with a running slope
not steeper than 1:20, doorways, ramps, curb ramps excluding the
flared sides, elevators, and platform lifts. All components of an
accessible route shall comply with the applicable requirements of
Chapter 4.

403 Walking Surfaces

403.1 General. Walking surfaces that are a part of an accessible
route shall comply with 403.
403.2 Floor or Ground Surface. Floor or ground surfaces shall
comply with 302.
403.3 Slope. The running slope of walking surfaces shall not be
steeper than 1:20. The cross slope of walking surfaces shall not be
steeper than 1:48.
403.4 Changes in Level. Changes in level shall comply with 303.
403.5 Clearances. Walking surfaces shall provide clearances
complying with 403.5.
EXCEPTION: Within employee work areas, clearances on common use
circulation paths shall be permitted to be decreased by work area
equipment provided that the decrease is essential to the function of
the work being performed.
403.5.1 Clear Width. Except as provided in 403.5.2 and 403.5.3,
the clear width of walking surfaces shall be 36 inches (915 mm)
minimum.
EXCEPTION: The clear width shall be permitted to be reduced to
32 inches (815 mm) minimum for a length of 24 inches (610 mm)
maximum provided that reduced width segments are separated by
segments that are 48 inches (1220 mm) long minimum and 36 inches
(915 mm) wide minimum.
403.5.2 Clear Width at Turn. Where the accessible route makes a
180 degree turn around an element which is less than 48

[[Page 59528]]

inches (1220 mm) wide, clear width shall be 42 inches (1065 mm)
minimum approaching the turn, 48 inches (1220 mm) minimum at the
turn and 42 inches (1065 mm) minimum leaving the turn.
EXCEPTION: Where the clear width at the turn is 60 inches (1525
mm) minimum compliance with 403.5.2 shall not be required.
403.5.3 Passing Spaces. An accessible route with a clear width
less than 60 inches (1525 mm) shall provide passing spaces at
intervals of 200 feet (61 m) maximum. Passing spaces shall be
either: a space 60 inches (1525 mm) minimum by 60 inches (1525 mm)
minimum; or, an intersection of two walking surfaces providing a T-
shaped space complying with 304.3.2 where the base and arms of the
T-shaped space extend 48 inches (1220 mm) minimum beyond the
intersection.
403.6 Handrails. Where handrails are provided along walking
surfaces with running slopes not steeper than 1:20 they shall comply
with 505.

404 Doors, Doorways, and Gates

404.1 General. Doors, doorways, and gates that are part of an
accessible route shall comply with 404.
EXCEPTION: Doors, doorways, and gates designed to be operated
only by security personnel shall not be required to comply with
404.2.7, 404.2.8, 404.2.9, 404.3.2 and 404.3.4 through 404.3.7.
404.2 Manual Doors, Doorways, and Manual Gates. Manual doors and
doorways and manual gates intended for user passage shall comply
with 404.2.
404.2.1 Revolving Doors, Gates, and Turnstiles. Revolving doors,
revolving gates, and turnstiles shall not be part of an accessible
route.
404.2.2 Double-Leaf Doors and Gates. At least one of the active
leaves of doorways with two leaves shall comply with 404.2.3 and
404.2.4.
404.2.3 Clear Width. Door openings shall provide a clear width
of 32 inches (815 mm) minimum. Clear openings of doorways with
swinging doors shall be measured between the face of the door and
the stop, with the door open 90 degrees. Openings more than 24
inches (610 mm) deep shall provide a clear opening of 36 inches (915
mm) minimum. There shall be no projections into the required clear
opening width lower than 34 inches (865 mm) above the finish floor
or ground. Projections into the clear opening width between 34
inches (865 mm) and 80 inches (2030 mm) above the finish floor or
ground shall not exceed 4 inches (100 mm).
EXCEPTIONS: 1. In alterations, a projection of \5/8\ inch (16
mm) maximum into the required clear width shall be permitted for the
latch side stop.
2. Door closers and door stops shall be permitted to be 78
inches (1980 mm) minimum above the finish floor or ground.
404.2.4 Maneuvering Clearances. Minimum maneuvering clearances
at doors and gates shall comply with 404.2.4. Maneuvering clearances
shall extend the full width of the doorway and the required latch
side or hinge side clearance.
EXCEPTION: Entry doors to hospital patient rooms shall not be
required to provide the clearance beyond the latch side of the door.
404.2.4.1 Swinging Doors and Gates. Swinging doors and gates
shall have maneuvering clearances complying with Table 404.2.4.1.

Table 404.2.4.1--Maneuvering Clearances at Manual Swinging Doors and Gates
----------------------------------------------------------------------------------------------------------------
Type of use Minimum maneuvering clearance
----------------------------------------------------------------------------------------------------------------
Perpendicular to Parallel to doorway (beyond latch
Approach direction Door or gate side doorway side unless noted)
----------------------------------------------------------------------------------------------------------------
From front....................... Pull................ 60 inches (1525 mm). 18 inches (455 mm).
From front....................... Push................ 48 inches (1220 mm). 0 inches (0 mm).\1\
From hinge side.................. Pull................ 60 inches (1525 mm). 36 inches (915 mm).
From hinge side.................. Pull................ 54 inches (1370 mm). 42 inches (1065 mm).
From hinge side.................. Push................ 42 inches (1065 mm) 22 inches (560 mm).\3\
\2\.
From latch side.................. Pull................ 48 inches (1220 mm) 24 inches (610 mm).
\4\.
From latch side.................. Push................ 42 inches (1065 mm) 24 inches (610 mm).
\4\.
----------------------------------------------------------------------------------------------------------------
\1\ Add 12 inches (305 mm) if closer and latch are provided.
\2\ Add 6 inches (150 mm) if closer and latch are provided.
\3\ Beyond hinge side.
\4\ Add 6 inches (150 mm) if closer is provided.

404.2.4.2 Doorways without Doors or Gates, Sliding Doors, and
Folding Doors. Doorways less than 36 inches (915 mm) wide without
doors or gates, sliding doors, or folding doors shall have
maneuvering clearances complying with Table 404.2.4.2.

Table 404.2.4.2--Maneuvering Clearances at Doorways Without Doors or Gates, Manual Sliding Doors, and Manual
Folding Doors
----------------------------------------------------------------------------------------------------------------
Minimum maneuvering clearance
------------------------------------------------------------------------
Approach direction Parallel to doorway (beyond stop/latch
Perpendicular to doorway side unless noted)
----------------------------------------------------------------------------------------------------------------
From Front............................. 48 inches (1220 mm)............ 0 inches (0 mm).
From side \1\.......................... 42 inches (1065 mm)............ 0 inches (0 mm).
From pocket/hinge side................. 42 inches (1065 mm)............ 22 inches (560 mm).\2\
From stop/latch side................... 42 inches (1065 mm)............ 24 inches (610 mm).
----------------------------------------------------------------------------------------------------------------
\1\ Doorway with no door only.
\2\ Beyond pocket/hinge side.

404.2.4.3 Recessed Doors and Gates. Maneuvering clearances for
forward approach shall be provided when any obstruction within 18
inches (455 mm) of the latch side of a doorway projects more than 8
inches (205 mm) beyond the face of the door, measured perpendicular
to the face of the door or gate.
404.2.4.4 Floor or Ground Surface. Floor or ground surface
within required maneuvering clearances shall comply with 302.
Changes in level are not permitted.
EXCEPTIONS: 1. Slopes not steeper than 1:48 shall be permitted.

[[Page 59529]]

2. Changes in level at thresholds complying with 404.2.5 shall
be permitted.
404.2.5 Thresholds. Thresholds, if provided at doorways, shall
be \1/2\ inch (13 mm) high maximum. Raised thresholds and changes in
level at doorways shall comply with 302 and 303.
EXCEPTION: Existing or altered thresholds \3/4\ inch (19 mm)
high maximum that have a beveled edge on each side with a slope not
steeper than 1:2 shall not be required to comply with 404.2.5.
404.2.6 Doors in Series and Gates in Series. The distance
between two hinged or pivoted doors in series and gates in series
shall be 48 inches (1220 mm) minimum plus the width of doors or
gates swinging into the space.
404.2.7 Door and Gate Hardware. Handles, pulls, latches, locks,
and other operable parts on doors and gates shall comply with 309.4.
Operable parts of such hardware shall be 34 inches (865 mm) minimum
and 48 inches (1220 mm) maximum above the finish floor or ground.
Where sliding doors are in the fully open position, operating
hardware shall be exposed and usable from both sides.
EXCEPTIONS: 1. Existing locks shall be permitted in any location
at existing glazed doors without stiles, existing overhead rolling
doors or grilles, and similar existing doors or grilles that are
designed with locks that are activated only at the top or bottom
rail.
2. Access gates in barrier walls and fences protecting pools,
spas, and hot tubs shall be permitted to have operable parts of the
release of latch on self-latching devices at 54 inches (1370 mm)
maximum above the finish floor or ground provided the self-latching
devices are not also self-locking devices and operated by means of a
key, electronic opener, or integral combination lock.
404.2.8 Closing Speed. Door and gate closing speed shall comply
with 404.2.8.
404.2.8.1 Door Closers and Gate Closers. Door closers and gate
closers shall be adjusted so that from an open position of 90
degrees, the time required to move the door to a position of 12
degrees from the latch is 5 seconds minimum.
404.2.8.2 Spring Hinges. Door and gate spring hinges shall be
adjusted so that from the open position of 70 degrees, the door or
gate shall move to the closed position in 1.5 seconds minimum.
404.2.9 Door and Gate Opening Force. Fire doors shall have a
minimum opening force allowable by the appropriate administrative
authority. The force for pushing or pulling open a door or gate
other than fire doors shall be as follows:
1. Interior hinged doors and gates: 5 pounds (22.2 N) maximum.
2. Sliding or folding doors: 5 pounds (22.2 N) maximum.
These forces do not apply to the force required to retract latch
bolts or disengage other devices that hold the door or gate in a
closed position.
404.2.10 Door and Gate Surfaces. Swinging door and gate surfaces
within 10 inches (255 mm) of the finish floor or ground measured
vertically shall have a smooth surface on the push side extending
the full width of the door or gate. Parts creating horizontal or
vertical joints in these surfaces shall be within \1/16\ inch (1.6
mm) of the same plane as the other. Cavities created by added kick
plates shall be capped.
EXCEPTIONS: 1. Sliding doors shall not be required to comply
with 404.2.10.
2. Tempered glass doors without stiles and having a bottom rail
or shoe with the top leading edge tapered at 60 degrees minimum from
the horizontal shall not be required to meet the 10 inch (255 mm)
bottom smooth surface height requirement.
3. Doors and gates that do not extend to within 10 inches (255
mm) of the finish floor or ground shall not be required to comply
with 404.2.10.
4. Existing doors and gates without smooth surfaces within 10
inches (255 mm) of the finish floor or ground shall not be required
to provide smooth surfaces complying with 404.2.10 provided that if
added kick plates are installed, cavities created by such kick
plates are capped.
404.2.11 Vision Lights. Doors, gates, and side lights adjacent
to doors or gates, containing one or more glazing panels that permit
viewing through the panels shall have the bottom of at least one
glazed panel located 43 inches (1090 mm) maximum above the finish
floor.
EXCEPTION: Vision lights with the lowest part more than 66
inches (1675 mm) from the finish floor or ground shall not be
required to comply with 404.2.11.
404.3 Automatic and Power-Assisted Doors and Gates. Automatic
doors and automatic gates shall comply with 404.3. Full-powered
automatic doors shall comply with ANSI/BHMA A156.10 (incorporated by
reference, see Referenced Standards'' in Chapter 1). Low-energy and
power-assisted doors shall comply with ANSI/BHMA A156.19 (1997 or
2002 edition) (incorporated by reference, see ``Referenced
Standards'' in Chapter 1).
404.3.1 Clear Width. Doorways shall provide a clear opening of
32 inches (815 mm) minimum in power-on and power-off mode. The
minimum clear width for automatic door systems in a doorway shall be
based on the clear opening provided by all leaves in the open
position.
404.3.2 Maneuvering Clearance. Clearances at power-assisted
doors and gates shall comply with 404.2.4. Clearances at automatic
doors and gates without standby power and serving an accessible
means of egress shall comply with 404.2.4.
EXCEPTION: Where automatic doors and gates remain open in the
power-off condition, compliance with 404.2.4 shall not be required.
404.3.3 Thresholds. Thresholds and changes in level at doorways
shall comply with 404.2.5.
404.3.4 Doors in Series and Gates in Series. Doors in series and
gates in series shall comply with 404.2.6.
404.3.5 Controls. Manually operated controls shall comply with
309. The clear floor space adjacent to the control shall be located
beyond the arc of the door swing.
404.3.6 Break Out Opening. Where doors and gates without standby
power are a part of a means of egress, the clear break out opening
at swinging or sliding doors and gates shall be 32 inches (815 mm)
minimum when operated in emergency mode.
EXCEPTION: Where manual swinging doors and gates comply with
404.2 and serve the same means of egress compliance with 404.3.6
shall not be required.
404.3.7 Revolving Doors, Revolving Gates, and Turnstiles.
Revolving doors, revolving gates, and turnstiles shall not be part
of an 405 Ramps
405.1 General. Ramps on accessible routes shall comply with 405.
EXCEPTION: In assembly areas, aisle ramps adjacent to seating
and not serving elements required to be on an accessible route shall
not be required to comply with 405.
405.2 Slope. Ramp runs shall have a running slope not steeper
than 1:12.
EXCEPTION: In existing sites, buildings, and facilities, ramps
shall be permitted to have running slopes steeper than 1:12
complying with Table 405.2 where such slopes are necessary due to
space limitations.

Table 405.2--Maximum Ramp Slope and Rise for Existing Sites, Buildings,
and Facilities
------------------------------------------------------------------------
Slope \1\ Maximum rise
------------------------------------------------------------------------
Steeper than 1:10 but not steeper than 1:8 3 inches (75 mm).
Steeper than 1:12 but not steeper than 6 inches (150 mm).
1:10.
------------------------------------------------------------------------
\1\ A slope steeper than 1:8 is prohibited.

405.3 Cross Slope. Cross slope of ramp runs shall not be steeper
than 1:48.
405.4 Floor or Ground Surfaces. Floor or ground surfaces of ramp
runs shall comply with 302. Changes in level other than the running
slope and cross slope are not permitted on ramp runs.
405.5 Clear Width. The clear width of a ramp run and, where
handrails are provided, the clear width between handrails shall be
36 inches (915 mm) minimum.
EXCEPTION: Within employee work areas, the required clear width
of ramps that are a part of common use circulation paths shall be
permitted to be decreased by work area equipment provided that the
decrease is essential to the function of the work being performed.
405.6 Rise. The rise for any ramp run shall be 30 inches (760
mm) maximum.
405.7 Landings. Ramps shall have landings at the top and the
bottom of each ramp run. Landings shall comply with 405.7.
405.7.1 Slope. Landings shall comply with 302. Changes in level
are not permitted.
EXCEPTION: Slopes not steeper than 1:48 shall be permitted.
405.7.2 Width. The landing clear width shall be at least as wide
as the widest ramp run leading to the landing.
405.7.3 Length. The landing clear length shall be 60 inches
(1525 mm) long minimum.
405.7.4 Change in Direction. Ramps that change direction between
runs at landings shall have a clear landing 60 inches (1525

[[Page 59530]]

mm) minimum by 60 inches (1525 mm) minimum.
405.7.5 Doorways. Where doorways are located adjacent to a ramp
landing, maneuvering clearances required by 404.2.4 and 404.3.2
shall be permitted to overlap the required landing area.
405.8 Handrails. Ramp runs with a rise greater than 6 inches
(150 mm) shall have handrails complying with 505.
EXCEPTION: Within employee work areas, handrails shall not be
required where ramps that are part of common use circulation paths
are designed to permit the installation of handrails complying with
505. Ramps not subject to the exception to 405.5 shall be designed
to maintain a 36 inch (915 mm) minimum clear width when handrails
are installed.
405.9 Edge Protection. Edge protection complying with 405.9.1 or
405.9.2 shall be provided on each side of ramp runs and at each side
of ramp landings.
EXCEPTIONS: 1. Edge protection shall not be required on ramps
that are not required to have handrails and have sides complying
with 406.3.
2. Edge protection shall not be required on the sides of ramp
landings serving an adjoining ramp run or stairway.
3. Edge protection shall not be required on the sides of ramp
landings having a vertical drop-off of \1/2\ inch (13 mm) maximum
within 10 inches (255 mm) horizontally of the minimum landing area
specified in 405.7.
405.9.1 Extended Floor or Ground Surface. The floor or ground
surface of the ramp run or landing shall extend 12 inches (305 mm)
minimum beyond the inside face of a handrail complying with 505.
405.9.2 Curb or Barrier. A curb or barrier shall be provided
that prevents the passage of a 4 inch (100 mm) diameter sphere,
where any portion of the sphere is within 4 inches (100 mm) of the
finish floor or ground surface.
405.10 Wet Conditions. Landings subject to wet conditions shall
be designed to prevent the accumulation of water.

406 Curb Ramps

406.1 General. Curb ramps accessible routes shall comply with
406, 405.2 through 405.5, and 405.10.
406.2 Counter Slope. Counter slopes of adjoining gutters and
road surfaces immediately adjacent to the curb ramp shall not be
steeper than 1:20. The adjacent surfaces at transitions at curb
ramps to walks, gutters, and streets shall be at the same level.
406.3 Sides of Curb Ramps. Where provided, curb ramp flares
shall not be steeper than 1:10.
406.4 Landings. Landings shall be provided at the tops of curb
ramps. The landing clear length shall be 36 inches (915 mm) minimum.
The landing clear width shall be at least as wide as the curb ramp,
excluding flared sides, leading to the landing.
EXCEPTION: In alterations, where there is no landing at the top
of curb ramps, curb ramp flares shall be provided and shall not be
steeper than 1:12.
406.5 Location. Curb ramps and the flared sides of curb ramps
shall be located so that they do not project into vehicular traffic
lanes, parking spaces, or parking access aisles. Curb ramps at
marked crossings shall be wholly contained within the markings,
excluding any flared sides.
406.6 Diagonal Curb Ramps. Diagonal or corner type curb ramps
with returned curbs or other well-defined edges shall have the edges
parallel to the direction of pedestrian flow. The bottom of diagonal
curb ramps shall have a clear space 48 inches (1220 mm) minimum
outside active traffic lanes of the roadway. Diagonal curb ramps
provided at marked crossings shall provide the 48 inches (1220 mm)
minimum clear space within the markings. Diagonal curb ramps with
flared sides shall have a segment of curb 24 inches (610 mm) long
minimum located on each side of the curb ramp and within the marked
crossing.
406.7 Islands. Raised islands in crossings shall be cut through
level with the street or have curb ramps at both sides. Each curb
ramp shall have a level area 48 inches (1220 mm) long minimum by 36
inches (915 mm) wide minimum at the top of the curb ramp in the part
of the island intersected by the crossings. Each 48 inch (1220 mm)
minimum by 36 inch (915 mm) minimum area shall be oriented so that
the 48 inch (1220 mm) minimum length is in the direction of the
running slope of the curb ramp it serves. The 48 inch (1220 mm)
minimum by 36 inch (915 mm) minimum areas and the accessible route
shall be permitted to overlap.

407 Elevators

407.1 General. Elevators shall comply with 407 and with ASME
A17.1 (incorporated by reference, see Referenced Standards'' in
Chapter 1). They shall be passenger elevators as classified by ASME
A17.1. Elevator operation shall be automatic.
407.2 Elevator Landing Requirements. Elevator landings shall
comply with 407.2.
407.2.1 Call Controls. Where elevator call buttons or keypads
are provided, they shall comply with 407.2.1 and 309.4. Call buttons
shall be raised or flush.
EXCEPTION: Existing elevators shall be permitted to have
recessed call buttons.
407.2.1.1 Height. Call buttons and keypads shall be located
within one of the reach ranges specified in 308, measured to the
centerline of the highest operable part.
EXCEPTION: Existing call buttons and existing keypads shall be
permitted to be located at 54 inches (1370 mm) maximum above the
finish floor, measured to the centerline of the highest operable
part.
407.2.1.2 Size. Call buttons shall be \3/4\ inch (19 mm) minimum
in the smallest dimension.
EXCEPTION: Existing elevator call buttons shall not be required
to comply with 407.2.1.2.
407.2.1.3 Clear Floor or Ground Space. A clear floor or ground
space complying with 305 shall be provided at call controls.
407.2.1.4 Location. The call button that designates the up
direction shall be located above the call button that designates the
down direction.
EXCEPTION: Destination-oriented elevators shall not be required
to comply with 407.2.1.4.
407.2.1.5 Signals. Call buttons shall have visible signals to
indicate when each call is registered and when each call is
answered.
EXCEPTIONS: 1. Destination-oriented elevators shall not be
required to comply with 407.2.1.5 provided that visible and audible
signals complying with 407.2.2 indicating which elevator car to
enter are provided.
2. Existing elevators shall not be required to comply with
407.2.1.5.
407.2.1.6 Keypads. Where keypads are provided, keypads shall be
in a standard telephone keypad arrangement and shall comply with
407.4.7.2.
407.2.2 Hall Signals. Hall signals, including in-car signals,
shall comply with 407.2.2.
407.2.2.1 Visible and Audible Signals. A visible and audible
signal shall be provided at each hoist-way entrance to indicate
which car is answering a call and the car's direction of travel.
Where in-car signals are provided, they shall be visible from the
floor area adjacent to the hall call buttons.
EXCEPTIONS: 1. Visible and audible signals shall not be required
at each destination-oriented elevator where a visible and audible
signal complying with 407.2.2 is provided indicating the elevator
car designation information.
2. In existing elevators, a signal indicating the direction of
car travel shall not be required.
407.2.2.2 Visible Signals. Visible signal fixtures shall be
centered at 72 inches (1830 mm) minimum above the finish floor or
ground. The visible signal elements shall be 2\1/2\ inches (64 mm)
minimum measured along the vertical centerline of the element.
Signals shall be visible from the floor area adjacent to the hall
call button.
EXCEPTIONS: 1. Destination-oriented elevators shall be permitted
to have signals visible from the floor area adjacent to the hoist-
way entrance.
2. Existing elevators shall not be required to comply with
407.2.2.2.
407.2.2.3 Audible Signals. Audible signals shall sound once for
the up direction and twice for the down direction, or shall have
verbal annunciators that indicate the direction of elevator car
travel. Audible signals shall have a frequency of 1500 Hz maximum.
Verbal annunciators shall have a frequency of 300 Hz minimum and
3000 Hz maximum. The audible signal and verbal annunciator shall be
10 dB minimum above ambient, but shall not exceed 80 dB, measured at
the hall call button.
EXCEPTIONS: 1. Destination-oriented elevators shall not be
required to comply with 407.2.2.3 provided that the audible tone and
verbal announcement is the same as those given at the call button or
call button keypad.
2. Existing elevators shall not be required to comply with the
requirements for frequency and dB range of audible signals.
407.2.2.4 Differentiation. Each destination-oriented elevator in
a bank of elevators shall have audible and visible means for
differentiation.
407.2.3 Hoist-way Signs. Signs at elevator hoist-ways shall
comply with 407.2.3.
407.2.3.1 Floor Designation. Floor designations complying with
703.2 and

[[Page 59531]]

703.4.1 shall be provided on both jambs of elevator hoist-way
entrances. Floor designations shall be provided in both tactile
characters and braille. Tactile characters shall be 2 inches (51 mm)
high minimum. A tactile star shall be provided on both jambs at the
main entry level.
407.2.3.2 Car Designations. Destination-oriented elevators shall
provide tactile car identification complying with 703.2 on both
jambs of the hoist-way immediately below the floor designation. Car
designations shall be provided in both tactile characters and
braille. Tactile characters shall be 2 inches (51 mm) high minimum.
407.3 Elevator Door Requirements. Hoist-way and car doors shall
comply with 407.3.
407.3.1 Type. Elevator doors shall be the horizontal sliding
type. Car gates shall be prohibited.
407.3.2 Operation. Elevator hoist-way and car doors shall open
and close automatically.
EXCEPTION: Existing manually operated hoist-way swing doors
shall be permitted provided that they comply with 404.2.3 and
404.2.9. Car door closing shall not be initiated until the hoist-way
door is closed.
407.3.3 Reopening Device. Elevator doors shall be provided with
a reopening device complying with 407.3.3 that shall stop and reopen
a car door and hoist-way door automatically if the door becomes
obstructed by an object or person.
EXCEPTION: Existing elevators with manually operated doors shall
not be required to comply with 407.3.3.
407.3.3.1 Height. The device shall be activated by sensing an
obstruction passing through the opening at 5 inches (125 mm) nominal
and 29 inches (735 mm) nominal above the finish floor.
407.3.3.2 Contact. The device shall not require physical contact
to be activated, although contact is permitted to occur before the
door reverses.
407.3.3.3 Duration. Door reopening devices shall remain
effective for 20 seconds minimum.
407.3.4 Door and Signal Timing. The minimum acceptable time from
notification that a car is answering a call or notification of the
car assigned at the means for the entry of destination information
until the doors of that car start to close shall be calculated from
the following equation:
T = D/(1.5 ft/s) or T = D/(455 mm/s) = 5 seconds minimum where T
equals the total time in seconds and D equals the distance (in feet
or millimeters) from the point in the lobby or corridor 60 inches
(1525 mm) directly in front of the farthest call button controlling
that car to the centerline of its hoist-way door.
EXCEPTIONS: 1. For cars with in-car lanterns, T shall be
permitted to begin when the signal is visible from the point 60
inches (1525 mm) directly in front of the farthest hall call button
and the audible signal is sounded.
2. Destination-oriented elevators shall not be required to
comply with 407.3.4.
407.3.5 Door Delay. Elevator doors shall remain fully open in
response to a car call for 3 seconds minimum.
407.3.6 Width. The width of elevator doors shall comply with
Table 407.4.1.
EXCEPTION: In existing elevators, a power-operated car door
complying with 404.2.3 shall be permitted.
407.4 Elevator Car Requirements. Elevator cars shall comply with
407.4.
407.4.1 Car Dimensions. Inside dimensions of elevator cars and
clear width of elevator doors shall comply with Table 407.4.1.
EXCEPTION: Existing elevator car configurations that provide a
clear floor area of 16 square feet (1.5 m2) minimum and also provide
an inside clear depth 54 inches (1370 mm) minimum and a clear width
36 inches (915 mm) minimum shall be permitted.

Table 407.4.1--Elevator Car Dimensions
----------------------------------------------------------------------------------------------------------------
Minimum dimensions
-------------------------------------------------------------------------------
Door location Inside car, back Inside car, back
Door clear width Inside car, side wall to front wall to inside
to side return face of door
----------------------------------------------------------------------------------------------------------------
Centered........................ 42 inches (1065 80 inches (2030 51 inches (1295 54 inches (1370
mm). mm). mm). mm).
Side (off-centered)............. 36 inches (915 mm) 68 inches (1725 51 inches (1295 54 inches (1370
\1\. mm). mm). mm).
Any............................. 36 inches (915 54 inches (1370 80 inches (2030 80 inches (2030
mm)\1\. mm). mm). mm).
Any............................. 36 inches (915 mm) 60 inches (1525 60 inches (1525 60 inches (1525
\1\. mm) \2\. mm) \2\. mm).\2\
----------------------------------------------------------------------------------------------------------------
\1\ A tolerance of minus 5/8 inch (16 mm) is permitted.
\2\ Other car configurations that provide a turning space complying with 304 with the door closed shall be
permitted.

407.4.2 Floor Surfaces. Floor surfaces in elevator cars shall
comply with 302 and 303.
407.4.3 Platform to Hoist-way Clearance. The clearance between
the car platform sill and the edge of any hoist-way landing shall be
1\1/4\ inch (32 mm) maximum.
407.4.4 Leveling. Each car shall be equipped with a self-
leveling feature that will automatically bring and maintain the car
at floor landings within a tolerance of \1/2\ inch (13 mm) under
rated loading to zero loading conditions.
407.4.5 Illumination. The level of illumination at the car
controls, platform, car threshold and car landing sill shall be 5
foot candles (54 lux) minimum.
407.4.6 Elevator Car Controls. Where provided, elevator car
controls shall comply with 407.4.6 and 309.4.
EXCEPTION: In existing elevators, where a new car operating
panel complying with 407.4.6 is provided, existing car operating
panels shall not be required to comply with 407.4.6.
407.4.6.1 Location. Controls shall be located within one of the
reach ranges specified in 308.
EXCEPTIONS: 1. Where the elevator panel serves more than 16
openings and a parallel approach is provided, buttons with floor
designations shall be permitted to be 54 inches (1370 mm) maximum
above the finish floor.
2. In existing elevators, car control buttons with floor
designations shall be permitted to be located 54 inches (1370 mm)
maximum above the finish floor where a parallel approach is
provided.
407.4.6.2 Buttons. Car control buttons with floor designations
shall comply with 407.4.6.2 and shall be raised or flush.
EXCEPTION: In existing elevators, buttons shall be permitted to
be recessed.
407.4.6.2.1 Size. Buttons shall be \3/4\ inch (19 mm) minimum in
their smallest dimension.
407.4.6.2.2 Arrangement. Buttons shall be arranged with numbers
in ascending order. When two or more columns of buttons are provided
they shall read from left to right.
407.4.6.3 Keypads. Car control keypads shall be in a standard
telephone keypad arrangement and shall comply with 407.4.7.2.
407.4.6.4 Emergency Controls. Emergency controls shall comply
with 407.4.6.4.
407.4.6.4.1 Height. Emergency control buttons shall have their
centerlines 35 inches (890 mm) minimum above the finish floor.
407.4.6.4.2 Location. Emergency controls, including the
emergency alarm, shall be grouped at the bottom of the panel.
407.4.7 Designations and Indicators of Car Controls.
Designations and indicators of car controls shall comply with
407.4.7.
EXCEPTION: In existing elevators, where a new car operating
panel complying with 407.4.7 is provided, existing car operating
panels shall not be required to comply with 407.4.7.
407.4.7.1 Buttons. Car control buttons shall comply with
407.4.7.1.
407.4.7.1.1 Type. Control buttons shall be identified by tactile
characters complying with 703.2.
407.4.7.1.2 Location. Raised character and braille designations
shall be placed immediately to the left of the control button to
which the designations apply.
EXCEPTION: Where space on an existing car operating panel
precludes tactile markings to the left of the controls, markings
shall be placed as near to the control as possible.

[[Page 59532]]

407.4.7.1.3 Symbols. The control button for the emergency stop,
alarm, door open, door close, main entry door, and phone shall be
identified with tactile symbols as shown in Figure 407.4.7.3 at the
end of this document.
407.4.7.1.4 Visible Indicators. Buttons with floor designations
shall be provided with visible indicators to show that a call has
been registered. The visible indication shall extinguish when the
car arrives at the designated floor.
407.4.7.2 Keypads. Keypads shall be identified by characters
complying with 703.5 and shall be centered on the corresponding
keypad button. The number five key shall have a single raised dot.
The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base
diameter and in other aspects comply with Table 703.3.1.
407.4.8 Car Position Indicators. Audible and visible car
position indicators shall be provided in elevator cars.
407.4.8.1 Visible Indicators. Visible indicators shall comply
with 407.4.8.1.
407.4.8.1.1 Size. Characters shall be \1/2\ inch (13 mm) high
minimum.
407.4.8.1.2 Location. Indicators shall be located above the car
control panel or above the door.
407.4.8.1.3 Floor Arrival. As the car passes a floor and when a
car stops at a floor served by the elevator, the corresponding
character shall illuminate.
EXCEPTION: Destination-oriented elevators shall not be required
to comply with 407.4.8.1.3 provided that the visible indicators
extinguish when the call has been answered.
407.4.8.1.4 Destination Indicator. In destination-oriented
elevators, a display shall be provided in the car with visible
indicators to show car destinations.
407.4.8.2 Audible Indicators. Audible indicators shall comply
with 407.4.8.2.
407.4.8.2.1 Signal Type. The signal shall be an automatic verbal
annunciator which announces the floor at which the car is about to
stop.
EXCEPTION: For elevators other than destination-oriented
elevators that have a rated speed of 200 feet per minute (1 m/s) or
less, a non-verbal audible signal with a frequency of 1500 Hz
maximum which sounds as the car passes or is about to stop at a
floor served by the elevator shall be permitted.
407.4.8.2.2 Signal Level. The verbal annunciator shall be 10 dB
minimum above ambient, but shall not exceed 80 dB, measured at the
annunciator.
407.4.8.2.3 Frequency. The verbal annunciator shall have a
frequency of 300 Hz minimum to 3000 Hz maximum.
407.4.9 Emergency Communication. Emergency two-way communication
systems shall comply with 308. Tactile symbols and characters shall
be provided adjacent to the device and shall comply with 703.2.

408 Limited-Use/Limited-Application Elevators

408.1 General. Limited-use/limited-application elevators shall
comply with 408 and with ASME A17.1 (incorporated by reference, see
Referenced Standards'' in Chapter 1). They shall be passenger
elevators as classified by ASME A17.1. Elevator operation shall be
automatic.
408.2 Elevator Landings. Landings serving limited-use/limited-
application elevators shall comply with 408.2.
408.2.1 Call Buttons. Elevator call buttons and keypads shall
comply with 407.2.1.
408.2.2 Hall Signals. Hall signals shall comply with 407.2.2.
408.2.3 Hoist-way Signs. Signs at elevator hoist-ways shall
comply with 407.2.3.1.
408.3 Elevator Doors. Elevator hoist-way doors shall comply with
408.3.
408.3.1 Sliding Doors. Sliding hoist-way and car doors shall
comply with 407.3.1 through 407.3.3 and 408.4.1.
408.3.2 Swinging Doors. Swinging hoist-way doors shall open and
close automatically and shall comply with 404, 407.3.2 and 408.3.2.
408.3.2.1 Power Operation. Swinging doors shall be power-
operated and shall comply with ANSI/BHMA A156.19 (1997 or 2002
edition) (incorporated by reference, see ``Referenced Standards'' in
Chapter 1).
408.3.2.2 Duration. Power-operated swinging doors shall remain
open for 20 seconds minimum when activated.
408.4 Elevator Cars. Elevator cars shall comply with 408.4.
408.4.1 Car Dimensions and Doors. Elevator cars shall provide a
clear width 42 inches (1065 mm) minimum and a clear depth 54 inches
(1370 mm) minimum. Car doors shall be positioned at the narrow ends
of cars and shall provide 32 inches (815 mm) minimum clear width.
EXCEPTIONS: 1. Cars that provide a clear width 51 inches (1295
mm) minimum shall be permitted to provide a clear depth 51 inches
(1295 mm) minimum provided that car doors provide a clear opening 36
inches (915 mm) wide minimum.
2. Existing elevator cars shall be permitted to provide a clear
width 36 inches (915 mm) minimum, clear depth 54 inches (1370 mm)
minimum, and a net clear platform area 15 square feet (1.4
m²) minimum.
408.4.2 Floor Surfaces. Floor surfaces in elevator cars shall
comply with 302 and 303.
408.4.3 Platform to Hoist-way Clearance. The platform to hoist-
way clearance shall comply with 407.4.3.
408.4.4 Leveling. Elevator car leveling shall comply with
407.4.4.
408.4.5 Illumination. Elevator car illumination shall comply
with 407.4.5.
408.4.6 Car Controls. Elevator car controls shall comply with
407.4.6. Control panels shall be centered on a side wall.
408.4.7 Designations and Indicators of Car Controls.
Designations and indicators of car controls shall comply with
407.4.7.
408.4.8 Emergency Communications. Car emergency signaling
devices complying with 407.4.9 shall be provided.

409 Private Residence Elevators

409.1 General. Private residence elevators that are provided
within a residential dwelling unit required to provide mobility
features complying with 809.2 through 809.4 shall comply with 409
and with ASME A17.1 (incorporated by reference, see ``Referenced
Standards'' in Chapter 1). They shall be passenger elevators as
classified by ASME A17.1. Elevator operation shall be automatic.
409.2 Call Buttons. Call buttons shall be \3/4\ inch (19 mm)
minimum in the smallest dimension and shall comply with 309.
409.3 Elevator Doors. Hoist-way doors, car doors, and car gates
shall comply with 409.3 and 404.
EXCEPTION: Doors shall not be required to comply with the
maneuvering clearance requirements in 404.2.4.1 for approaches to
the push side of swinging doors.
409.3.1 Power Operation. Elevator car and hoist-way doors and
gates shall be power operated and shall comply with ANSI/BHMA
A156.19 (1997 or 2002 edition) (incorporated by reference, see
``Referenced Standards'' in Chapter 1). Power operated doors and
gates shall remain open for 20 seconds minimum when activated.
EXCEPTION: In elevator cars with more than one opening, hoist-
way doors and gates shall be permitted to be of the manual-open,
self-close type.
409.3.2 Location. Elevator car doors or gates shall be
positioned at the narrow end of the clear floor spaces required by
409.4.1.
409.4 Elevator Cars. Private residence elevator cars shall
comply with 409.4.
409.4.1 Inside Dimensions of Elevator Cars. Elevator cars shall
provide a clear floor space of 36 inches (915 mm) minimum by 48
inches (1220 mm) minimum and shall comply with 305.
409.4.2 Floor Surfaces. Floor surfaces in elevator cars shall
comply with 302 and 303.
409.4.3 Platform to Hoist-way Clearance. The clearance between
the car platform and the edge of any landing sill shall be 1\1/2\
inch (38 mm) maximum.
409.4.4 Leveling. Each car shall automatically stop at a floor
landing within a tolerance of \1/2\ inch (13 mm) under rated loading
to zero loading conditions.
409.4.5 Illumination Levels. Elevator car illumination shall
comply with 407.4.5.
409.4.6 Car Controls. Elevator car control buttons shall comply
with 409.4.6, 309.3, 309.4, and shall be raised or flush.
409.4.6.1 Size. Control buttons shall be \3/4\ inch (19 mm)
minimum in their smallest dimension.
409.4.6.2 Location. Control panels shall be on a side wall, 12
inches (305 mm) minimum from any adjacent wall.
409.4.7 Emergency Communications. Emergency two-way
communication systems shall comply with 409.4.7.
409.4.7.1 Type. A telephone and emergency signal device shall be
provided in the car.
409.4.7.2 Operable Parts. The telephone and emergency signaling
device shall comply with 309.3 and 309.4.
409.4.7.3 Compartment. If the telephone or device is in a closed
compartment, the compartment door hardware shall comply with 309.
409.4.7.4 Cord. The telephone cord shall be 29 inches (735 mm)
long minimum.

410 Platform Lifts

410.1 General. Platform lifts shall comply with ASME A18.1 (1999
edition or 2003 edition) (incorporated by reference, see Referenced
Standards'' in Chapter 1).

[[Page 59533]]

Platform lifts shall not be attendant operated and shall provide
unassisted entry and exit from the lift.
410.2 Floor Surfaces. Floor surfaces in platform lifts shall
comply with 302 and 303.
410.3 Clear Floor Space. Clear floor space in platform lifts
shall comply with 305.
410.4 Platform to Runway Clearance. The clearance between the
platform sill and the edge of any runway landing shall be 1\1/4\
inch (32 mm) maximum.
410.5 Operable Parts. Controls for platform lifts shall comply
with 309.
410.6 Doors and Gates. Platform lifts shall have low-energy
power operated doors or gates complying with 404.3. Doors shall
remain open for 20 seconds minimum. End doors and gates shall
provide a clear width 32 inches (815 mm) minimum. Side doors and
gates shall provide a clear width 42 inches (1065 mm) minimum.
EXCEPTION: Platform lifts serving two landings maximum and
having doors or gates on opposite sides shall be permitted to have
self-closing manual doors or gates.

Chapter 5: General Site and Building Elements

501 General

501.1 Scope. The provisions of Chapter 5 shall apply where
required by Chapter 2 or where referenced by a requirement in this
document.

502 Parking Spaces

502.1 General. Car and van parking spaces shall comply with 502.
Where parking spaces are marked with lines, width measurements of
parking spaces and access aisles shall be made from the centerline
of the markings.
EXCEPTION: Where parking spaces or access aisles are not
adjacent to another parking space or access aisle, measurements
shall be permitted to include the full width of the line defining
the parking space or access aisle.
502.2 Vehicle Spaces. Car parking spaces shall be 96 inches
(2440 mm) wide minimum and van parking spaces shall be 132 inches
(3350 mm) wide minimum, shall be marked to define the width, and
shall have an adjacent access aisle complying with 502.3.
EXCEPTION: Van parking spaces shall be permitted to be 96 inches
(2440 mm) wide minimum where the access aisle is 96 inches (2440 mm)
wide minimum.
502.3 Access Aisle. Access aisles serving parking spaces shall
comply with 502.3. Access aisles shall adjoin an accessible route.
Two parking spaces shall be permitted to share a common access
aisle.
502.3.1 Width. Access aisles serving car and van parking spaces
shall be 60 inches (1525 mm) wide minimum.
502.3.2 Length. Access aisles shall extend the full length of
the parking spaces they serve.
502.3.3 Marking. Access aisles shall be marked so as to
discourage parking in them.
502.3.4 Location. Access aisles shall not overlap the vehicular
way. Access aisles shall be permitted to be placed on either side of
the parking space except for angled van parking spaces which shall
have access aisles located on the passenger side of the parking
spaces.
502.4 Floor or Ground Surfaces. Parking spaces and access aisles
serving them shall comply with 302. Access aisles shall be at the
same level as the parking spaces they serve. Changes in level are
not permitted.
EXCEPTION: Slopes not steeper than 1:48 shall be permitted.
502.5 Vertical Clearance. Parking spaces for vans and access
aisles and vehicular routes serving them shall provide a vertical
clearance of 98 inches (2490 mm) minimum.
502.6 Identification. Parking space identification signs shall
include the International Symbol of Accessibility complying with
703.7.2.1. Signs identifying van parking spaces shall contain the
designation ``van accessible.'' Signs shall be 60 inches (1525 mm)
minimum above the finish floor or ground surface measured to the
bottom of the sign.
502.7 Relationship to Accessible Routes. Parking spaces and
access aisles shall be designed so that cars and vans, when parked,
cannot obstruct the required clear width of adjacent accessible
routes.

503 Passenger Loading Zones

503.1 General. Passenger loading zones shall comply with 503.
503.2 Vehicle Pull-Up Space. Passenger loading zones shall
provide a vehicular pull-up space 96 inches (2440 mm) wide minimum
and 20 feet (6100 mm) long minimum.
503.3 Access Aisle. Passenger loading zones shall provide access
aisles complying with 503 adjacent to the vehicle pull-up space.
Access aisles shall adjoin an accessible route and shall not overlap
the vehicular way.
503.3.1 Width. Access aisles serving vehicle pull-up spaces
shall be 60 inches (1525 mm) wide minimum.
503.3.2 Length. Access aisles shall extend the full length of
the vehicle pull-up spaces they serve.
503.3.3 Marking. Access aisles shall be marked so as to
discourage parking in them.
503.4 Floor and Ground Surfaces. Vehicle pull-up spaces and
access aisles serving them shall comply with 302. Access aisles
shall be at the same level as the vehicle pull-up space they serve.
Changes in level are not permitted.
EXCEPTION: Slopes not steeper than 1:48 shall be permitted.
503.5 Vertical Clearance. Vehicle pull-up spaces, access aisles
serving them, and a vehicular route from an entrance to the
passenger loading zone, and from the passenger loading zone to a
vehicular exit shall provide a vertical clearance of 114 inches
(2895 mm) minimum.

504 Stairways

504.1 General. Stairs shall comply with 504.
504.2 Treads and Risers. All steps on a flight of stairs shall
have uniform riser heights and uniform tread depths. Risers shall be
4 inches (100 mm) high minimum and 7 inches (180 mm) high maximum.
Treads shall be 11 inches (280 mm) deep minimum.
504.3 Open Risers. Open risers are not permitted.
504.4 Tread Surface. Stair treads shall comply with 302. Changes
in level are not permitted.
EXCEPTION: Treads shall be permitted to have a slope not steeper
than 1:48.
504.5 Nosings. The radius of curvature at the leading edge of
the tread shall be \1/2\ inch (13 mm) maximum. Nosings that project
beyond risers shall have the underside of the leading edge curved or
beveled. Risers shall be permitted to slope under the tread at an
angle of 30 degrees maximum from vertical. The permitted projection
of the nosing shall extend 1\1/2\ inches (38 mm) maximum over the
tread below.
504.6 Handrails. Stairs shall have handrails complying with 505.
504.7 Wet Conditions. Stair treads and landings subject to wet
conditions shall be designed to prevent the accumulation of water.

505 Handrails

505.1 General. Handrails provided along walking surfaces
complying with 403, required at ramps complying with 405, and
required at stairs complying with 504 shall comply with 505.
505.2 Where Required. Handrails shall be provided on both sides
of stairs and ramps.
EXCEPTION: In assembly areas, handrails shall not be required on
both sides of aisle ramps where a handrail is provided at either
side or within the aisle width.
505.3 Continuity. Handrails shall be continuous within the full
length of each stair flight or ramp run. Inside handrails on
switchback or dogleg stairs and ramps shall be continuous between
flights or runs.
EXCEPTION: In assembly areas, handrails on ramps shall not be
required to be continuous in aisles serving seating.
505.4 Height. Top of gripping surfaces of handrails shall be 34
inches (865 mm) minimum and 38 inches (965 mm) maximum vertically
above walking surfaces, stair nosings, and ramp surfaces. Handrails
shall be at a consistent height above walking surfaces, stair
nosings, and ramp surfaces.
505.5 Clearance. Clearance between handrail gripping surfaces
and adjacent surfaces shall be 1\1/2\ inches (38 mm) minimum.
505.6 Gripping Surface. Handrail gripping surfaces shall be
continuous along their length and shall not be obstructed along
their tops or sides. The bottoms of handrail gripping surfaces shall
not be obstructed for more than 20 percent of their length. Where
provided, horizontal projections shall occur 1\1/2\ inches (38 mm)
minimum below the bottom of the handrail gripping surface.
EXCEPTIONS: 1. Where handrails are provided along walking
surfaces with slopes not steeper than 1:20, the bottoms of handrail
gripping surfaces shall be permitted to be obstructed along their
entire length where they are integral to crash rails or bumper
guards.
2. The distance between horizontal projections and the bottom of
the gripping surface shall be permitted to be reduced by 1/8 inch
(3.2 mm) for each \1/2\ inch (13 mm) of additional handrail
perimeter dimension that exceeds 4 inches (100 mm).

[[Page 59534]]

505.7 Cross Section. Handrail gripping surfaces shall have a
cross section complying with 505.7.1 or 505.7.2.
505.7.1 Circular Cross Section. Handrail gripping surfaces with
a circular cross section shall have an outside diameter of 1\1/4\
inches (32 mm) minimum and 2 inches (51 mm) maximum.
505.7.2 Non-Circular Cross Sections. Handrail gripping surfaces
with a noncircular cross section shall have a perimeter dimension of
4 inches (100 mm) minimum and 6\1/4\ inches (160 mm) maximum, and a
cross-section dimension of 2\1/4\ inches (57 mm) maximum.
505.8 Surfaces. Handrail gripping surfaces and any surfaces
adjacent to them shall be free of sharp or abrasive elements and
shall have rounded edges.
505.9 Fittings. Handrails shall not rotate within their
fittings.
505.10 Handrail Extensions. Handrail gripping surfaces shall
extend beyond and in the same direction of stair flights and ramp
runs in accordance with 505.10.
EXCEPTIONS: 1. Extensions shall not be required for continuous
handrails at the inside turn of switchback or dogleg stairs and
ramps.
2. In assembly areas, extensions shall not be required for ramp
handrails in aisles serving seating where the handrails are
discontinuous to provide access to seating and to permit crossovers
within aisles.
3. In alterations, full extensions of handrails shall not be
required where such extensions would be hazardous due to plan
configuration.
505.10.1 Top and Bottom Extension at Ramps. Ramp handrails shall
extend horizontally above the landing for 12 inches (305 mm) minimum
beyond the top and bottom of ramp runs. Extensions shall return to a
wall, guard, or the landing surface, or shall be continuous to the
handrail of an adjacent ramp run.
505.10.2 Top Extension at Stairs. At the top of a stair flight,
handrails shall extend horizontally above the landing for 12 inches
(305 mm) minimum beginning directly above the first riser nosing.
Extensions shall return to a wall, guard, or the landing surface, or
shall be continuous to the handrail of an adjacent stair flight.
505.10.3 Bottom Extension at Stairs. At the bottom of a stair
flight, handrails shall extend at the slope of the stair flight for
a horizontal distance at least equal to one tread depth beyond the
last riser nosing. Extension shall return to a wall, guard, or the
landing surface, or shall be continuous to the handrail of an
adjacent stair flight.

CHAPTER 6: PLUMBING ELEMENTS AND FACILITIES

601 General

601.1 Scope. The provisions of Chapter 6 shall apply where
required by Chapter 2 or where referenced by a requirement in this
document.

602 Drinking Fountains

602.1 General. Drinking fountains shall comply with 307 and 602.
602.2 Clear Floor Space. Units shall have a clear floor or
ground space complying with 305 positioned for a forward approach
and centered on the unit. Knee and toe clearance complying with 306
shall be provided.
EXCEPTION: A parallel approach complying with 305 shall be
permitted at units for children's use where the spout is 30 inches
(760 mm) maximum above the finish floor or ground and is 3\1/2\
inches (90 mm) maximum from the front edge of the unit, including
bumpers.
602.3 Operable Parts. Operable parts shall comply with 309.
602.4 Spout Height. Spout outlets shall be 36 inches (915 mm)
maximum above the finish floor or ground.
602.5 Spout Location. The spout shall be located 15 inches (380
mm) minimum from the vertical support and 5 inches (125 mm) maximum
from the front edge of the unit, including bumpers.
602.6 Water Flow. The spout shall provide a flow of water 4
inches (100 mm) high minimum and shall be located 5 inches (125 mm)
maximum from the front of the unit. The angle of the water stream
shall be measured horizontally relative to the front face of the
unit. Where spouts are located less than 3 inches (75 mm) of the
front of the unit, the angle of the water stream shall be 30 degrees
maximum. Where spouts are located between 3 inches (75 mm) and 5
inches (125 mm) maximum from the front of the unit, the angle of the
water stream shall be 15 degrees maximum.
602.7 Drinking Fountains for Standing Persons. Spout outlets of
drinking fountains for standing persons shall be 38 inches (965 mm)
minimum and 43 inches (1090 mm) maximum above the finish floor or
ground.

603 Toilet and Bathing Rooms

603.1 General. Toilet and bathing rooms shall comply with 603.
603.2 Clearances. Clearances shall comply with 603.2.
603.2.1 Turning Space. Turning space complying with 304 shall be
provided within the room.
603.2.2 Overlap. Required clear floor spaces, clearance at
fixtures, and turning space shall be permitted to overlap.
603.2.3 Door Swing. Doors shall not swing into the clear floor
space or clearance required for any fixture. Doors shall be
permitted to swing into the required turning space.
EXCEPTIONS: 1. Doors to a toilet room or bathing room for a
single occupant accessed only through a private office and not for
common use or public use shall be permitted to swing into the clear
floor space or clearance provided the swing of the door can be
reversed to comply with 603.2.3.
2. Where the toilet room or bathing room is for individual use
and a clear floor space complying with 305.3 is provided within the
room beyond the arc of the door swing, doors shall be permitted to
swing into the clear floor space or clearance required for any
fixture.
603.3 Mirrors. Mirrors located above lavatories or countertops
shall be installed with the bottom edge of the reflecting surface 40
inches (1015 mm) maximum above the finish floor or ground. Mirrors
not located above lavatories or countertops shall be installed with
the bottom edge of the reflecting surface 35 inches (890 mm) maximum
above the finish floor or ground.
603.4 Coat Hooks and Shelves. Coat hooks shall be located within
one of the reach ranges specified in 308. Shelves shall be located
40 inches (1015 mm) minimum and 48 inches (1220 mm) maximum above
the finish floor.

604 Water Closets and Toilet Compartments

604.1 General. Water closets and toilet compartments shall
comply with 604.2 through 604.8.
EXCEPTION: Water closets and toilet compartments for children's
use shall be permitted to comply with 604.9.
604.2 Location. The water closet shall be positioned with a wall
or partition to the rear and to one side. The centerline of the
water closet shall be 16 inches (405 mm) minimum to 18 inches (455
mm) maximum from the side wall or partition, except that the water
closet shall be 17 inches (430 mm) minimum and 19 inches (485 mm)
maximum from the side wall or partition in the ambulatory accessible
toilet compartment specified in 604.8.2. Water closets shall be
arranged for a left-hand or right-hand approach.
604.3 Clearance. Clearances around water closets and in toilet
compartments shall comply with 604.3.
604.3.1 Size. Clearance around a water closet shall be 60 inches
(1525 mm) minimum measured perpendicular from the side wall and 56
inches (1420 mm) minimum measured perpendicular from the rear wall.
604.3.2 Overlap. The required clearance around the water closet
shall be permitted to overlap the water closet, associated grab
bars, dispensers, sanitary napkin disposal units, coat hooks,
shelves, accessible routes, clear floor space and clearances
required at other fixtures, and the turning space. No other fixtures
or obstructions shall be located within the required water closet
clearance.
EXCEPTION: In residential dwelling units, a lavatory complying
with 606 shall be permitted on the rear wall 18 inches (455 mm)
minimum from the water closet centerline where the clearance at the
water closet is 66 inches (1675 mm) minimum measured perpendicular
from the rear wall.
604.4 Seats. The seat height of a water closet above the finish
floor shall be 17 inches (430 mm) minimum and 19 inches (485 mm)
maximum measured to the top of the seat. Seats shall not be sprung
to return to a lifted position.
EXCEPTIONS: 1. A water closet in a toilet room for a single
occupant accessed only through a private office and not for common
use or public use shall not be required to comply with 604.4.
2. In residential dwelling units, the height of water closets
shall be permitted to be 15 inches (380 mm) minimum and 19 inches
(485 mm) maximum above the finish floor measured to the top of the
seat.
604.5 Grab Bars. Grab bars for water closets shall comply with
609. Grab bars shall be provided on the side wall closest to the
water closet and on the rear wall.
EXCEPTIONS: 1. Grab bars shall not be required to be installed
in a toilet room for

[[Page 59535]]

a single occupant accessed only through a private office and not for
common use or public use provided that reinforcement has been
installed in walls and located so as to permit the installation of
grab bars complying with 604.5.
2. In residential dwelling units, grab bars shall not be
required to be installed in toilet or bathrooms provided that
reinforcement has been installed in walls and located so as to
permit the installation of grab bars complying with 604.5.
3. In detention or correction facilities, grab bars shall not be
required to be installed in housing or holding cells that are
specially designed without protrusions for purposes of suicide
prevention.
604.5.1 Side Wall. The side wall grab bar shall be 42 inches
(1065 mm) long minimum, located 12 inches (305 mm) maximum from the
rear wall and extending 54 inches (1370 mm) minimum from the rear
wall.
604.5.2 Rear Wall. The rear wall grab bar shall be 36 inches
(915 mm) long minimum and extend from the centerline of the water
closet 12 inches (305 mm) minimum on one side and 24 inches (610 mm)
minimum on the other side.
EXCEPTIONS: 1. The rear grab bar shall be permitted to be 24
inches (610 mm) long minimum, centered on the water closet, where
wall space does not permit a length of 36 inches (915 mm) minimum
due to the location of a recessed fixture adjacent to the water
closet.
2. Where an administrative authority requires flush controls for
flush valves to be located in a position that conflicts with the
location of the rear grab bar, then the rear grab bar shall be
permitted to be split or shifted to the open side of the toilet
area.
604.6 Flush Controls. Flush controls shall be hand operated or
automatic. Hand operated flush controls shall comply with 309. Flush
controls shall be located on the open side of the water closet
except in ambulatory accessible compartments complying with 604.8.2.
604.7 Dispensers. Toilet paper dispensers shall comply with
309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm)
maximum in front of the water closet measured to the centerline of
the dispenser. The outlet of the dispenser shall be 15 inches (380
mm) minimum and 48 inches (1220 mm) maximum above the finish floor
and shall not be located behind grab bars. Dispensers shall not be
of a type that controls delivery or that does not allow continuous
paper flow.
604.8 Toilet Compartments. Wheelchair accessible toilet
compartments shall meet the requirements of 604.8.1 and 604.8.3.
Compartments containing more than one plumbing fixture shall comply
with 603. Ambulatory accessible compartments shall comply with
604.8.2 and 604.8.3.
604.8.1 Wheelchair Accessible Compartments. Wheelchair
accessible compartments shall comply with 604.8.1.
604.8.1.1 Size. Wheelchair accessible compartments shall be 60
inches (1525 mm) wide minimum measured perpendicular to the side
wall, and 56 inches (1420 mm) deep minimum for wall hung water
closets and 59 inches (1500 mm) deep minimum for floor mounted water
closets measured perpendicular to the rear wall. Wheelchair
accessible compartments for children's use shall be 60 inches (1525
mm) wide minimum measured perpendicular to the side wall, and 59
inches (1500 mm) deep minimum for wall hung and floor mounted water
closets measured perpendicular to the rear wall.
604.8.1.2 Doors. Toilet compartment doors, including door
hardware, shall comply with 404 except that if the approach is to
the latch side of the compartment door, clearance between the door
side of the compartment and any obstruction shall be 42 inches (1065
mm) minimum. Doors shall be located in the front partition or in the
side wall or partition farthest from the water closet. Where located
in the front partition, the door opening shall be 4 inches (100 mm)
maximum from the side wall or partition farthest from the water
closet. Where located in the side wall or partition, the door
opening shall be 4 inches (100 mm) maximum from the front partition.
The door shall be self-closing. A door pull complying with 404.2.7
shall be placed on both sides of the door near the latch. Toilet
compartment doors shall not swing into the minimum required
compartment area.
604.8.1.3 Approach. Compartments shall be arranged for left-hand
or right-hand approach to the water closet.
604.8.1.4 Toe Clearance. The front partition and at least one
side partition shall provide a toe clearance of 9 inches (230 mm)
minimum above the finish floor and 6 inches (150 mm) deep minimum
beyond the compartment-side face of the partition, exclusive of
partition support members. Compartments for children's use shall
provide a toe clearance of 12 inches (305 mm) minimum above the
finish floor.
EXCEPTION: Toe clearance at the front partition is not required
in a compartment greater than 62 inches (1575 mm) deep with a wall-
hung water closet or 65 inches (1650 mm) deep with a floor-mounted
water closet. Toe clearance at the side partition is not required in
a compartment greater than 66 inches (1675 mm) wide. Toe clearance
at the front partition is not required in a compartment for
children's use that is greater than 65 inches (1650 mm) deep.
604.8.1.5 Grab Bars. Grab bars shall comply with 609. A sidewall
grab bar complying with 604.5.1 shall be provided and shall be
located on the wall closest to the water closet. In addition, a
rear-wall grab bar complying with 604.5.2 shall be provided.
604.8.2 Ambulatory Accessible Compartments. Ambulatory
accessible compartments shall comply with 604.8.2.
604.8.2.1 Size. Ambulatory accessible compartments shall have a
depth of 60 inches (1525 mm) minimum and a width of 35 inches (890
mm) minimum and 37 inches (940 mm) maximum.
604.8.2.2 Doors. Toilet compartment doors, including door
hardware, shall comply with 404, except that if the approach is to
the latch side of the compartment door, clearance between the door
side of the compartment and any obstruction shall be 42 inches (1065
mm) minimum. The door shall be self-closing. A door pull complying
with 404.2.7 shall be placed on both sides of the door near the
latch. Toilet compartment doors shall not swing into the minimum
required compartment area.
604.8.2.3 Grab Bars. Grab bars shall comply with 609. A sidewall
grab bar complying with 604.5.1 shall be provided on both sides of
the compartment.
604.8.3 Coat Hooks and Shelves. Coat hooks shall be located
within one of the reach ranges specified in 308. Shelves shall be
located 40 inches (1015 mm) minimum and 48 inches (1220 mm) maximum
above the finish floor.
604.9 Water Closets and Toilet Compartments for Children's Use.
Water closets and toilet compartments for children's use shall
comply with 604.9.
604.9.1 Location. The water closet shall be located with a wall
or partition to the rear and to one side. The centerline of the
water closet shall be 12 inches (305 mm) minimum and 18 inches (455
mm) maximum from the side wall or partition, except that the water
closet shall be 17 inches (430 mm) minimum and 19 inches (485 mm)
maximum from the side wall or partition in the ambulatory accessible
toilet compartment specified in 604.8.2. Compartments shall be
arranged for left-hand or right-hand approach to the water closet.
604.9.2 Clearance. Clearance around a water closet shall comply
with 604.3.
604.9.3 Height. The height of water closets shall be 11 inches
(280 mm) minimum and 17 inches (430 mm) maximum measured to the top
of the seat. Seats shall not be sprung to return to a lifted
position.
604.9.4 Grab Bars. Grab bars for water closets shall comply with
604.5.
604.9.5 Flush Controls. Flush controls shall be hand operated or
automatic. Hand operated flush controls shall comply with 309.2 and
309.4 and shall be installed 36 inches (915 mm) maximum above the
finish floor. Flush controls shall be located on the open side of
the water closet except in ambulatory accessible compartments
complying with 604.8.2.
604.9.6 Dispensers. Toilet paper dispensers shall comply with
309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm)
maximum in front of the water closet measured to the centerline of
the dispenser. The outlet of the dispenser shall be 14 inches (355
mm) minimum and 19 inches (485 mm) maximum above the finish floor.
There shall be a clearance of 1\1/2\ inches (38 mm) minimum below
the grab bar. Dispensers shall not be of a type that controls
delivery or that does not allow continuous paper flow.
604.9.7 Toilet Compartments. Toilet compartments shall comply
with 604.8.

605 Urinals

605.1 General. Urinals shall comply with 605.
605.2 Height and Depth. Urinals shall be the stall-type or the
wall-hung type with the rim 17 inches (430 mm) maximum above the
finish floor or ground. Urinals shall be 13\1/2\ inches (345 mm)
deep minimum measured from the outer face of the urinal rim to the
back of the fixture.
605.3 Clear Floor Space. A clear floor or ground space complying
with 305 positioned for forward approach shall be provided.

[[Page 59536]]

605.4 Flush Controls. Flush controls shall be hand operated or
automatic. Hand operated flush controls shall comply with 309.

606 Lavatories and Sinks

606.1 General. Lavatories and sinks shall comply with 606.
606.2 Clear Floor Space. A clear floor space complying with 305,
positioned for a forward approach, and knee and toe clearance
complying with 306 shall be provided.
EXCEPTIONS: 1. A parallel approach complying with 305 shall be
permitted to a kitchen sink in a space where a cook top or
conventional range is not provided and to wet bars.
2. A lavatory in a toilet room or bathing facility for a single
occupant accessed only through a private office and not for common
use or public use shall not be required to provide knee and toe
clearance complying with 306.
3. In residential dwelling units, cabinetry shall be permitted
under lavatories and kitchen sinks provided that all of the
following conditions are met:
(a) the cabinetry can be removed without removal or replacement
of the fixture;
(b) the finish floor extends under the cabinetry; and
(c) the walls behind and surrounding the cabinetry are finished.
4. A knee clearance of 24 inches (610 mm) minimum above the
finish floor or ground shall be permitted at lavatories and sinks
used primarily by children 6 through 12 years where the rim or
counter surface is 31 inches (785 mm) maximum above the finish floor
or ground.
5. A parallel approach complying with 305 shall be permitted to
lavatories and sinks used primarily by children 5 years and younger.
6. The dip of the overflow shall not be considered in
determining knee and toe clearances.
7. No more than one bowl of a multi-bowl sink shall be required
to provide knee and toe clearance complying with 306.
606.3 Height. Lavatories and sinks shall be installed with the
front of the higher of the rim or counter surface 34 inches (865 mm)
maximum above the finish floor or ground.
EXCEPTIONS: 1. A lavatory in a toilet or bathing facility for a
single occupant accessed only through a private office and not for
common use or public use shall not be required to comply with 606.3.
2. In residential dwelling unit kitchens, sinks that are
adjustable to variable heights, 29 inches (735 mm) minimum and 36
inches (915 mm) maximum, shall be permitted where rough-in plumbing
permits connections of supply and drain pipes for sinks mounted at
the height of 29 inches (735 mm).
606.4 Faucets. Controls for faucets shall comply with 309. Hand-
operated metering faucets shall remain open for 10 seconds minimum.
606.5 Exposed Pipes and Surfaces. Water supply and drain pipes
under lavatories and sinks shall be insulated or otherwise
configured to protect against contact. There shall be no sharp or
abrasive surfaces under lavatories and sinks.

607 Bathtubs

607.1 General. Bathtubs shall comply with 607.
607.2 Clearance. Clearance in front of bathtubs shall extend the
length of the bathtub and shall be 30 inches (760 mm) wide minimum.
A lavatory complying with 606 shall be permitted at the control end
of the clearance. Where a permanent seat is provided at the head end
of the bathtub, the clearance shall extend 12 inches (305 mm)
minimum beyond the wall at the head end of the bathtub.
607.3 Seat. A permanent seat at the head end of the bathtub or a
removable in-tub seat shall be provided. Seats shall comply with
610.
607.4 Grab Bars. Grab bars for bathtubs shall comply with 609
and shall be provided in accordance with 607.4.1 or 607.4.2.
EXCEPTIONS: 1. Grab bars shall not be required to be installed
in a bathtub located in a bathing facility for a single occupant
accessed only through a private office and not for common use or
public use provided that reinforcement has been installed in walls
and located so as to permit the installation of grab bars complying
with 607.4.
2. In residential dwelling units, grab bars shall not be
required to be installed in bathtubs located in bathing facilities
provided that reinforcement has been installed in walls and located
so as to permit the installation of grab bars complying with 607.4.
607.4.1 Bathtubs With Permanent Seats. For bathtubs with
permanent seats, grab bars shall be provided in accordance with
607.4.1.
607.4.1.1 Back Wall. Two grab bars shall be installed on the
back wall, one located in accordance with 609.4 and the other
located 8 inches (205 mm) minimum and 10 inches (255 mm) maximum
above the rim of the bathtub. Each grab bar shall be installed 15
inches (380 mm) maximum from the head end wall and 12 inches (305
mm) maximum from the control end wall.
607.4.1.2 Control End Wall. A grab bar 24 inches (610 mm) long
minimum shall be installed on the control end wall at the front edge
of the bathtub.
607.4.2 Bathtubs Without Permanent Seats. For bathtubs without
permanent seats, grab bars shall comply with 607.4.2.
607.4.2.1 Back Wall. Two grab bars shall be installed on the
back wall, one located in accordance with 609.4 and other located 8
inches (205 mm) minimum and 10 inches (255 mm) maximum above the rim
of the bathtub. Each grab bar shall be 24 inches (610 mm) long
minimum and shall be installed 24 inches (610 mm) maximum from the
head end wall and 12 inches (305 mm) maximum from the control end
wall.
607.4.2.2 Control End Wall. A grab bar 24 inches (610 mm) long
minimum shall be installed on the control end wall at the front edge
of the bathtub.
607.4.2.3 Head End Wall. A grab bar 12 inches (305 mm) long
minimum shall be installed on the head end wall at the front edge of
the bathtub.
607.5 Controls. Controls, other than drain stoppers, shall be
located on an end wall. Controls shall be between the bathtub rim
and grab bar, and between the open side of the bathtub and the
centerline of the width of the bathtub. Controls shall comply with
309.4.
607.6 Shower Spray Unit and Water. A shower spray unit with a
hose 59 inches (1500 mm) long minimum that can be used both as a
fixed-position shower head and as a handheld shower shall be
provided. The shower spray unit shall have an on/off control with a
non-positive shut-off. If an adjustable height shower head on a
vertical bar is used, the bar shall be installed so as not to
obstruct the use of grab bars. Bathtub shower spray units shall
deliver water that is 120 [deg]F (49 [deg]C) maximum.
607.7 Bathtub Enclosures. Enclosures for bathtubs shall not
obstruct controls, faucets, shower and spray units or obstruct
transfer from wheelchairs onto bathtub seats or into bathtubs.
Enclosures on bathtubs shall not have tracks installed on the rim of
the open face of the bathtub.

608 Shower Compartments

608.1 General. Shower compartments shall comply with 608.
608.2 Size and Clearances for Shower Compartments. Shower
compartments shall have sizes and clearances complying with 608.2.
608.2.1 Transfer Type Shower Compartments. Transfer type shower
compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear
inside dimensions measured at the center points of opposing sides
and shall have a 36 inch (915 mm) wide minimum entry on the face of
the shower compartment. Clearance of 36 inches (915 mm) wide minimum
by 48 inches (1220 mm) long minimum measured from the control wall
shall be provided.
608.2.2 Standard Roll-In Type Shower Compartments. Standard
roll-in type shower compartments shall be 30 inches (760 mm) wide
minimum by 60 inches (1525 mm) deep minimum clear inside dimensions
measured at center points of opposing sides and shall have a 60
inches (1525 mm) wide minimum entry on the face of the shower
compartment.
608.2.2.1 Clearance. A 30 inch (760 mm) wide minimum by 60 inch
(1525 mm) long minimum clearance shall be provided adjacent to the
open face of the shower compartment.
EXCEPTION: A lavatory complying with 606 shall be permitted on
one 30 inch (760 mm) wide minimum side of the clearance provided
that it is not on the side of the clearance adjacent to the controls
or, where provided, not the side of the clearance adjacent to the
shower seat.
608.2.3 Alternate Roll-In Type Shower Compartments. Alternate
roll-in type shower compartments shall be 36 inches (915 mm) wide
and 60 inches (1525 mm) deep minimum clear inside dimensions
measured at center points of opposing sides. A 36 inch (915 mm) wide
minimum entry shall be provided at one end of the long side of the
compartment.
608.3 Grab Bars. Grab bars shall comply with 609 and shall be
provided in accordance with 608.3. Where multiple grab bars are
used, required horizontal grab bars shall be

[[Page 59537]]

installed at the same height above the finish floor.
EXCEPTIONS: 1. Grab bars shall not be required to be installed
in a shower located in a bathing facility for a single occupant
accessed only through a private office, and not for common use or
public use provided that reinforcement has been installed in walls
and located so as to permit the installation of grab bars complying
with 608.3.
2. In residential dwelling units, grab bars shall not be
required to be installed in showers located in bathing facilities
provided that reinforcement has been installed in walls and located
so as to permit the installation of grab bars complying with 608.3.
608.3.1 Transfer Type Shower Compartments. In transfer type
compartments, grab bars shall be provided across the control wall
and back wall to a point 18 inches (455 mm) from the control wall.
608.3.2 Standard Roll-In Type Shower Compartments. Where a seat
is provided in standard roll-in type shower compartments, grab bars
shall be provided on the back wall and the side wall opposite the
seat. Grab bars shall not be provided above the seat. Where a seat
is not provided in standard roll-in type shower compartments, grab
bars shall be provided on three walls. Grab bars shall be installed
6 inches (150 mm) maximum from adjacent walls.
608.3.3 Alternate Roll-In Type Shower Compartments. In alternate
roll-in type shower compartments, grab bars shall be provided on the
back wall and the side wall farthest from the compartment entry.
Grab bars shall not be provided above the seat. Grab bars shall be
installed 6 inches (150 mm) maximum from adjacent walls.
608.4 Seats. A folding or non-folding seat shall be provided in
transfer type shower compartments. A folding seat shall be provided
in roll-in type showers required in transient lodging guest rooms
with mobility features complying with 806.2. Seats shall comply with
610.
EXCEPTION: In residential dwelling units, seats shall not be
required in transfer type shower compartments provided that
reinforcement has been installed in walls so as to permit the
installation of seats complying with 608.4.
608.5 Controls. Controls, faucets, and shower spray units shall
comply with 309.4.
608.5.1 Transfer Type Shower Compartments. In transfer type
shower compartments, the controls, faucets, and shower spray unit
shall be installed on the side wall opposite the seat 38 inches (965
mm) minimum and 48 inches (1220 mm) maximum above the shower floor
and shall be located on the control wall 15 inches (380 mm) maximum
from the centerline of the seat toward the shower opening.
608.5.2 Standard Roll-In Type Shower Compartments. In standard
roll-in type shower compartments, the controls, faucets, and shower
spray unit shall be located above the grab bar, but no higher than
48 inches (1220 mm) above the shower floor. Where a seat is
provided, the controls, faucets, and shower spray unit shall be
installed on the back wall adjacent to the seat wall and shall be
located 27 inches (685 mm) maximum from the seat wall.
608.5.3 Alternate Roll-In Type Shower Compartments. In alternate
roll-in type shower compartments, the controls, faucets, and shower
spray unit shall be located above the grab bar, but no higher than
48 inches (1220 mm) above the shower floor. Where a seat is
provided, the controls, faucets, and shower spray unit shall be
located on the side wall adjacent to the seat 27 inches (685 mm)
maximum from the side wall behind the seat or shall be located on
the back wall opposite the seat 15 inches (380 mm) maximum, left or
right, of the centerline of the seat. Where a seat is not provided,
the controls, faucets, and shower spray unit shall be installed on
the side wall farthest from the compartment entry.
608.6 Shower Spray Unit and Water. A shower spray unit with a
hose 59 inches (1500 mm) long minimum that can be used both as a
fixed-position shower head and as a handheld shower shall be
provided. The shower spray unit shall have an on/off control with a
non-positive shut-off. If an adjustable-height shower head on a
vertical bar is used, the bar shall be installed so as not to
obstruct the use of grab bars. Shower spray units shall deliver
water that is 120 [deg]F (49 [deg]C) maximum.
EXCEPTION: A fixed shower head located at 48 inches (1220 mm)
maximum above the shower finish floor shall be permitted instead of
a hand-held spray unit in facilities that are not medical care
facilities, long-term care facilities, transient lodging guest
rooms, or residential dwelling units.
608.7 Thresholds. Thresholds in roll-in type shower compartments
shall be \1/2\ inch (13 mm) high maximum in accordance with 303. In
transfer type shower compartments, thresholds \1/2\ inch (13 mm)
high maximum shall be beveled, rounded, or vertical.
EXCEPTION: A threshold 2 inches (51 mm) high maximum shall be
permitted in transfer type shower compartments in existing
facilities where provision of a \1/2\ inch (13 mm) high threshold
would disturb the structural reinforcement of the floor slab.
608.8 Shower Enclosures. Enclosures for shower compartments
shall not obstruct controls, faucets, and shower spray units or
obstruct transfer from wheelchairs onto shower seats.

609 Grab Bars

609.1 General. Grab bars in toilet facilities and bathing
facilities shall comply with 609.
609.2 Cross Section. Grab bars shall have a cross section
complying with 609.2.1 or 609.2.2.
609.2.1 Circular Cross Section. Grab bars with circular cross
sections shall have an outside diameter of 1\1/4\ inches (32 mm)
minimum and 2 inches (51 mm) maximum.
609.2.2 Non-Circular Cross Section. Grab bars with non-circular
cross sections shall have a cross-section dimension of 2 inches (51
mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum
and 4.8 inches (120 mm) maximum.
609.3 Spacing. The space between the wall and the grab bar shall
be 1\1/2\ inches (38 mm). The space between the grab bar and
projecting objects below and at the ends shall be 1\1/2\ inches (38
mm) minimum. The space between the grab bar and projecting objects
above shall be 12 inches (305 mm) minimum.
EXCEPTION: The space between the grab bars and shower controls,
shower fittings, and other grab bars above shall be permitted to be
1\1/2\ inches (38 mm) minimum.
609.4 Position of Grab Bars. Grab bars shall be installed in a
horizontal position, 33 inches (840 mm) minimum and 36 inches (915
mm) maximum above the finish floor measured to the top of the
gripping surface, except that at water closets for children's use
complying with 604.9, grab bars shall be installed in a horizontal
position 18 inches (455 mm) minimum and 27 inches (685 mm) maximum
above the finish floor measured to the top of the gripping surface.
The height of the lower grab bar on the back wall of a bathtub shall
comply with 607.4.1.1 or 607.4.2.1.
609.5 Surface Hazards. Grab bars and any wall or other surfaces
adjacent to grab bars shall be free of sharp or abrasive elements
and shall have rounded edges.
609.6 Fittings. Grab bars shall not rotate within their
fittings.
609.7 Installation. Grab bars shall be installed in any manner
that provides a gripping surface at the specified locations and that
does not obstruct the required clear floor space.
609.8 Structural Strength. Allowable stresses shall not be
exceeded for materials used when a vertical or horizontal force of
250 pounds (1112 N) is applied at any point on the grab bar,
fastener, mounting device, or supporting structure.

610 Seats

610.1 General. Seats in bathtubs and shower compartments shall
comply with 610.
610.2 Bathtub Seats. The top of bathtub seats shall be 17 inches
(430 mm) minimum and 19 inches (485 mm) maximum above the bathroom
finish floor. The depth of a removable in-tub seat shall be 15
inches (380 mm) minimum and 16 inches (405 mm) maximum. The seat
shall be capable of secure placement. Permanent seats at the head
end of the bathtub shall be 15 inches (380 mm) deep minimum and
shall extend from the back wall to or beyond the outer edge of the
bathtub.
610.3 Shower Compartment Seats. Where a seat is provided in a
standard roll-in shower compartment, it shall be a folding type,
shall be installed on the side wall adjacent to the controls, and
shall extend from the back wall to a point within 3 inches (75 mm)
of the compartment entry. Where a seat is provided in an alternate
roll-in type shower compartment, it shall be a folding type, shall
be installed on the front wall opposite the back wall, and shall
extend from the adjacent side wall to a point within 3 inches (75
mm) of the compartment entry. In transfer-type showers, the seat
shall extend from the back wall to a point within 3 inches (75 mm)
of the compartment entry. The top of the seat shall be 17 inches
(430 mm) minimum and 19 inches (485 mm) maximum above the bathroom
finish floor. Seats shall comply with 610.3.1 or 610.3.2.
610.3.1 Rectangular Seats. The rear edge of a rectangular seat
shall be 2\1/2\ inches (64 mm) maximum and the front edge 15 inches

[[Page 59538]]

(380 mm) minimum and 16 inches (405 mm) maximum from the seat wall.
The side edge of the seat shall be 1\1/2\ inches (38 mm) maximum
from the adjacent wall.
610.3.2 L-Shaped Seats. The rear edge of an L-shaped seat shall
be 2\1/2\ inches (64 mm) maximum and the front edge 15 inches (380
mm) minimum and 16 inches (405 mm) maximum from the seat wall. The
rear edge of the ``L'' portion of the seat shall be 1\1/2\ inches
(38 mm) maximum from the wall and the front edge shall be 14 inches
(355 mm) minimum and 15 inches (380 mm) maximum from the wall. The
end of the ``L'' shall be 22 inches (560 mm) minimum and 23 inches
maximum (585 mm) from the main seat wall.
610.4 Structural Strength. Allowable stresses shall not be
exceeded for materials used when a vertical or horizontal force of
250 pounds (1112 N) is applied at any point on the seat, fastener,
mounting device, or supporting structure.

611 Washing Machines and Clothes Dryers

611.1 General. Washing machines and clothes dryers shall comply
with 611.
611.2 Clear Floor Space. A clear floor or ground space complying
with 305 positioned for parallel approach shall be provided. The
clear floor or ground space shall be centered on the appliance.
611.3 Operable Parts. Operable parts, including doors, lint
screens, and detergent and bleach compartments shall comply with
309.
611.4 Height. Top loading machines shall have the door to the
laundry compartment located 36 inches (915 mm) maximum above the
finish floor. Front loading machines shall have the bottom of the
opening to the laundry compartment located 15 inches (380 mm)
minimum and 36 inches (915 mm) maximum above the finish floor.

612 Saunas and Steam Rooms

612.1 General. Saunas and steam rooms shall comply with 612.
612.2 Bench. Where seating is provided in saunas and steam
rooms, at least one bench shall comply with 903. Doors shall not
swing into the clear floor space required by 903.2.
EXCEPTION: A readily removable bench shall be permitted to
obstruct the turning space required by 612.3 and the clear floor or
ground space required by 903.2.
612.3 Turning Space. A turning space complying with 304 shall be
provided within saunas and steam rooms.

Chapter 7: Communication Elements and Features

701 General

701.1 Scope. The provisions of Chapter 7 shall apply where
required by Chapter 2 or where referenced by a requirement in this
document.

702 Fire Alarm Systems

702.1 General. Fire alarm systems shall have permanently
installed audible and visible alarms complying with NFPA 72 (1999 or
2002 edition) (incorporated by reference, see Referenced Standards''
in Chapter 1), except that the maximum allowable sound level of
audible notification appliances complying with section 4-3.2.1 of
NFPA 72 (1999 edition) shall have a sound level no more than 110 dB
at the minimum hearing distance from the audible appliance. In
addition, alarms in guest rooms required to provide communication
features shall comply with sections 4-3 and 4-4 of NFPA 72 (1999
edition) or sections 7.4 and 7.5 of NFPA 72 (2002 edition).
EXCEPTION: Fire alarm systems in medical care facilities shall
be permitted to be provided in accordance with industry practice.

703 Signs

703.1 General. Signs shall comply with 703. Where both visual
and tactile characters are required, either one sign with both
visual and tactile characters, or two separate signs, one with
visual, and one with tactile characters, shall be provided.
703.2 Raised Characters. Raised characters shall comply with
703.2 and shall be duplicated in braille complying with 703.3.
Raised characters shall be installed in accordance with 703.4.
703.2.1 Depth. Raised characters shall be \1/32\ inch (0.8 mm)
minimum above their background.
703.2.2 Case. Characters shall be uppercase.
703.2.3 Style. Characters shall be sans serif. Characters shall
not be italic, oblique, script, highly decorative, or of other
unusual forms.
703.2.4 Character Proportions. Characters shall be selected from
fonts where the width of the uppercase letter ``O'' is 55 percent
minimum and 110 percent maximum of the height of the uppercase
letter ``I''.
703.2.5 Character Height. Character height measured vertically
from the baseline of the character shall be \5/8\ inch (16 mm)
minimum and 2 inches (51 mm) maximum based on the height of the
uppercase letter ``I''.
EXCEPTION: Where separate raised and visual characters with the
same information are provided, raised character height shall be
permitted to be \1/2\ inch (13 mm) minimum.
703.2.6 Stroke Thickness. Stroke thickness of the uppercase
letter ``I'' shall be 15 percent maximum of the height of the
character.
703.2.7 Character Spacing. Character spacing shall be measured
between the two closest points of adjacent raised characters within
a message, excluding word spaces. Where characters have rectangular
cross sections, spacing between individual raised characters shall
be \1/8\ inch (3.2 mm) minimum and 4 times the raised character
stroke width maximum. Where characters have other cross sections,
spacing between individual raised characters shall be \1/16\ inch
(1.6 mm) minimum and 4 times the raised character stroke width
maximum at the base of the cross sections, and \1/8\ inch (3.2 mm)
minimum and 4 times the raised character stroke width maximum at the
top of the cross sections. Characters shall be separated from raised
borders and decorative elements \3/8\ inch (9.5 mm) minimum.
703.2.8 Line Spacing. Spacing between the baselines of separate
lines of raised characters within a message shall be 135 percent
minimum and 170 percent maximum of the raised character height.
703.3 Braille. Braille shall be contracted (Grade 2) and shall
comply with 703.3 and 703.4.
703.3.1 Dimensions and Capitalization. Braille dots shall have a
domed or rounded shape and shall comply with Table 703.3.1. The
indication of an uppercase letter or letters shall only be used
before the first word of sentences, proper nouns and names,
individual letters of the alphabet, initials, and acronyms.

Table 703.3.1--Braille Dimensions
------------------------------------------------------------------------
Minimum in inches Maximum
Measurement range in inches
------------------------------------------------------------------------
Dot base diameter......................... 0.059 (1.5 mm) to 0.063 (1.6
mm).
Distance between two dots in the same cell 0.090 (2.3 mm) to 0.100 (2.5
\1\. mm).
Distance between corresponding dots in 0.241 (6.1 mm) to 0.300 (7.6
adjacent cells \1\. mm).
Dot height................................ 0.025 (0.6 mm) to 0.037 (0.9
mm).
Distance between corresponding dots from 0.395 (10 mm) to 0.400 (10.2
one cell directly below \1\. mm).
------------------------------------------------------------------------
\1\ Measured center to center.

703.3.2 Position. Braille shall be positioned below the
corresponding text. If text is multi-lined, braille shall be placed
below the entire text. Braille shall be separated \3/8\ inch (9.5
mm) minimum from any other tactile characters and \3/8\ inch (9.5
mm) minimum from raised borders and decorative elements.
EXCEPTION: Braille provided on elevator car controls shall be
separated \3/16\ inch (4.8 mm) minimum and shall be located either
directly below or adjacent to the corresponding raised characters or
symbols.
703.4 Installation Height and Location. Signs with tactile
characters shall comply with 703.4.
703.4.1 Height Above Finish Floor or Ground. Tactile characters
on signs shall be located 48 inches (1220 mm) minimum above the
finish floor or ground surface, measured from the baseline of the
lowest tactile character and 60 inches (1525 mm) maximum above the
finish floor or ground surface, measured from the baseline of the
highest tactile character.
EXCEPTION: Tactile characters for elevator car controls shall
not be required to comply with 703.4.1.
703.4.2 Location. Where a tactile sign is provided at a door,
the sign shall be located alongside the door at the latch side.
Where a tactile sign is provided at double doors with one active
leaf, the sign shall be located on the inactive leaf. Where a
tactile sign is provided at double doors with two active leafs, the
sign shall be located to the right of the right hand door. Where
there is no wall space at the latch side of a single door or at the
right side of double doors, signs shall be located on the nearest
adjacent wall. Signs containing tactile characters shall be located

[[Page 59539]]

so that a clear floor space of 18 inches (455 mm) minimum by 18
inches (455 mm) minimum, centered on the tactile characters, is
provided beyond the arc of any door swing between the closed
position and 45 degree open position.
EXCEPTION: Signs with tactile characters shall be permitted on
the push side of doors with closers and without hold-open devices.
703.5 Visual Characters. Visual characters shall comply with
703.5.
EXCEPTION: Where visual characters comply with 703.2 and are
accompanied by braille complying with 703.3, they shall not be
required to comply with 703.5.2 through 703.5.9.
703.5.1 Finish and Contrast. Characters and their background
shall have a non-glare finish. Characters shall contrast with their
background with either light characters on a dark background or dark
characters on a light background.
703.5.2 Case. Characters shall be uppercase or lowercase or a
combination of both.
703.5.3 Style. Characters shall be conventional in form.
Characters shall not be italic, oblique, script, highly decorative,
or of other unusual forms.
703.5.4 Character Proportions. Characters shall be selected from
fonts where the width of the uppercase letter ``O'' is 55 percent
minimum and 110 percent maximum of the height of the uppercase
letter ``I''.
703.5.5 Character Height. Minimum character height shall comply
with Table 703.5.5. Viewing distance shall be measured as the
horizontal distance between the character and an obstruction
preventing further approach towards the sign. Character height shall
be based on the uppercase letter ``I''.

Table 703.5.5--Visual Character Height
------------------------------------------------------------------------
Height to finish floor or
ground from baseline of Horizontal Minimum character
character viewing distance height
------------------------------------------------------------------------
40 inches (1015 mm) to less less than 72 \5/8\ inch (16 mm) \5/
than or equal to 70 inches inches (1830 mm) 8\ inch (16 mm),
(1780 mm). 72 inches (1830 plus \1/8\ inch (3.2
mm) and greater. mm) per foot (305
mm) of viewing
distance above 72
inches (1830 mm).
Greater than 70 inches (1780 less than 180 2 inches (51 mm).
mm) to less than or equal to inches (4570 mm).
120 inches (3050 mm).
180 inches (4570 2 inches (51 mm),
mm) and greater. plus \1/8\ inch (3.2
mm) per foot (305
mm) of viewing
distance above 180
inches (4570 mm).
Greater than 120 inches (3050 less than 21 feet 3 inches (75 mm).
mm). (6400 mm).
21 feet (6400 mm) 3 inches (75 mm),
and greater. plus \1/8\ inch (3.2
mm) per foot (305
mm) of viewing
distance above 21
feet (6400 mm).
------------------------------------------------------------------------

703.5.6 Height From Finish Floor or Ground. Visual characters
shall be 40 inches (1015 mm) minimum above the finish floor or
ground.
EXCEPTION: Visual characters indicating elevator car controls
shall not be required to comply with 703.5.6.
703.5.7 Stroke Thickness. Stroke thickness of the uppercase
letter ``I'' shall be 10 percent minimum and 30 percent maximum of
the height of the character.
703.5.8 Character Spacing. Character spacing shall be measured
between the two closest points of adjacent characters, excluding
word spaces. Spacing between individual characters shall be 10
percent minimum and 35 percent maximum of character height.
703.5.9 Line Spacing. Spacing between the baselines of separate
lines of characters within a message shall be 135 percent minimum
and 170 percent maximum of the character height.
703.6 Pictograms. Pictograms shall comply with 703.6.
703.6.1 Pictogram Field. Pictograms shall have a field height of
6 inches (150 mm) minimum. Characters and braille shall not be
located in the pictogram field.
703.6.2 Finish and Contrast. Pictograms and their field shall
have a non-glare finish. Pictograms shall contrast with their field
with either a light pictogram on a dark field or a dark pictogram on
a light field.
703.6.3 Text Descriptors. Pictograms shall have text descriptors
located directly below the pictogram field. Text descriptors shall
comply with 703.2, 703.3 and 703.4.
703.7 Symbols of Accessibility. Symbols of accessibility shall
comply with 703.7.
703.7.1 Finish and Contrast. Symbols of accessibility and their
background shall have a non-glare finish. Symbols of accessibility
shall contrast with their background with either a light symbol on a
dark background or a dark symbol on a light background.
703.7.2 Symbols.
703.7.2.1 International Symbol of Accessibility. The
International Symbol of Accessibility shall comply with Figure
703.7.2.1 at the end of this document.
703.7.2.2 International Symbol of TTY. The International Symbol
of TTY shall comply with Figure 703.7.2.2 at the end of this
document.
703.7.2.3 Volume Control Telephones. Telephones with a volume
control shall be identified by a pictogram of a telephone handset
with radiating sound waves.
703.7.2.4. Assistive Listening Systems. Assistive listening
systems shall be identified by the International Symbol of Access
for Hearing Loss complying with Figure 703.7.2.4 at the end of this
document.

704 Telephones

704.1 General. Public telephones shall comply with 704.
704.2 Wheelchair Accessible Telephones. Wheelchair accessible
telephones shall comply with 704.2.
704.2.1 Clear Floor or Ground Space. A clear floor or ground
space complying with 305 shall be provided. The clear floor or
ground space shall not be obstructed by bases, enclosures, or seats.
704.2.1.1 Parallel Approach. Where a parallel approach is
provided, the distance from the edge of the telephone enclosure to
the face of the telephone unit shall be 10 inches (255 mm) maximum.
704.2.1.2 Forward Approach. Where a forward approach is
provided, the distance from the front edge of a counter within the
telephone enclosure to the face of the telephone unit shall be 20
inches (510 mm) maximum.
704.2.2 Operable Parts. Operable parts shall comply with 309.
Telephones shall have pushbutton controls where such service is
available.
704.2.3 Telephone Directories. Telephone directories, where
provided, shall be located in accordance with 309.
704.2.4 Cord Length. The cord from the telephone to the handset
shall be 29 inches (735 mm) long minimum.
704.3 Volume Control Telephones. Public telephones required to
have volume controls shall be equipped with a receive volume control
that provides a gain adjustable up to 20 dB minimum. For incremental
volume control, provide at least one intermediate step of 12 dB of
gain minimum. An automatic reset shall be provided.
704.4 TTYs. TTYs required at a public pay telephone shall be
permanently affixed within, or adjacent to, the telephone enclosure.
Where an acoustic coupler is used, the telephone cord shall be
sufficiently long to allow connection of the TTY and the telephone
receiver.
704.4.1 Height. When in use, the touch surface of TTY keypads
shall be 34 inches (865 mm) minimum above the finish floor.
EXCEPTION: Where seats are provided, TTYs shall not be required
to comply with 704.4.1.
704.5 TTY Shelf. Public pay telephones required to accommodate
portable TTYs shall be equipped with a shelf and an electrical
outlet within or adjacent to the telephone enclosure. The telephone
handset shall be capable of being placed flush on the surface of the
shelf. The shelf shall be capable of accommodating a TTY and shall
have 6 inches (150 mm) minimum vertical clearance above the area
where the TTY is to be placed.

[[Page 59540]]

705 Detectable Warnings

705.1 General. Detectable warnings shall consist of a surface of
truncated domes and shall comply with 705.
705.1.1 Dome Size. Truncated domes in a detectable warning
surface shall have a base diameter of 0.9 inch (23 mm) minimum and
1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base
diameter minimum to 65 percent of the base diameter maximum, and a
height of 0.2 inch (5.1 mm).
705.1.2 Dome Spacing. Truncated domes in a detectable warning
surface shall have a center-to-center spacing of 1.6 inches (41 mm)
minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing
of 0.65 inch (17 mm) minimum, measured between the most adjacent
domes on a square grid.
705.1.3 Contrast. Detectable warning surfaces shall contrast
visually with adjacent walking surfaces either light-on-dark, or
dark-on-light.
705.2 Platform Edges. Detectable warning surfaces at platform
boarding edges shall be 24 inches (610 mm) wide and shall extend the
full length of the public use areas of the platform.

706 Assistive Listening Systems

706.1 General. Assistive listening systems required in assembly
areas shall comply with 706.
706.2 Receiver Jacks. Receivers required for use with an
assistive listening system shall include a \1/8\ inch (3.2 mm)
standard mono jack.
706.3 Receiver Hearing-Aid Compatibility. Receivers required to
be hearing-aid compatible shall interface with telecoils in hearing
aids through the provision of neckloops.
706.4 Sound Pressure Level. Assistive listening systems shall be
capable of providing a sound pressure level of 110 dB minimum and
118 dB maximum with a dynamic range on the volume control of 50 dB.
706.5 Signal-to-Noise Ratio. The signal-to-noise ratio for
internally generated noise in assistive listening systems shall be
18 dB minimum.
706.6 Peak Clipping Level. Peak clipping shall not exceed 18 dB
of clipping relative to the peaks of speech.

707 Automatic Teller Machines and Fare Machines

707.1 General. Automatic teller machines and fare machines shall
comply with 707.
707.2 Clear Floor or Ground Space. A clear floor or ground space
complying with 305 shall be provided.
EXCEPTION: Clear floor or ground space shall not be required at
drive-up only automatic teller machines and fare machines.
707.3 Operable Parts. Operable parts shall comply with 309.
Unless a clear or correct key is provided, each operable part shall
be able to be differentiated by sound or touch, without activation.
EXCEPTION: Drive-up only automatic teller machines and fare
machines shall not be required to comply with 309.2 and 309.3.
707.4 Privacy. Automatic teller machines shall provide the
opportunity for the same degree of privacy of input and output
available to all individuals.
707.5 Speech Output. Machines shall be speech enabled. Operating
instructions and orientation, visible transaction prompts, user
input verification, error messages, and all displayed information
for full use shall be accessible to and independently usable by
individuals with vision impairments. Speech shall be delivered
through a mechanism that is readily available to all users,
including but not limited to, an industry standard connector or a
telephone handset. Speech shall be recorded or digitized human, or
synthesized.
EXCEPTIONS: 1. Audible tones shall be permitted instead of
speech for visible output that is not displayed for security
purposes, including but not limited to, asterisks representing
personal identification numbers.
2. Advertisements and other similar information shall not be
required to be audible unless they convey information that can be
used in the transaction being conducted.
3. Where speech synthesis cannot be supported, dynamic
alphabetic output shall not be required to be audible.
707.5.1 User Control. Speech shall be capable of being repeated
or interrupted. Volume control shall be provided for the speech
function.
EXCEPTION: Speech output for any single function shall be
permitted to be automatically interrupted when a transaction is
selected.
707.5.2 Receipts. Where receipts are provided, speech output
devices shall provide audible balance inquiry information, error
messages, and all other information on the printed receipt necessary
to complete or verify the transaction.
EXCEPTIONS: 1. Machine location, date and time of transaction,
customer account number, and the machine identifier shall not be
required to be audible.
2. Information on printed receipts that duplicates information
available on-screen shall not be required to be presented in the
form of an audible receipt.
3. Printed copies of bank statements and checks shall not be
required to be audible.
707.6 Input. Input devices shall comply with 707.6.
707.6.1 Input Controls. At least one tactilely discernible input
control shall be provided for each function. Where provided, key
surfaces not on active areas of display screens, shall be raised
above surrounding surfaces. Where membrane keys are the only method
of input, each shall be tactilely discernible from surrounding
surfaces and adjacent keys.
707.6.2 Numeric Keys. Numeric keys shall be arranged in a 12-key
ascending or descending telephone keypad layout. The number five key
shall be tactilely distinct from the other keys.
707.6.3 Function Keys. Function keys shall comply with 707.6.3.
707.6.3.1 Contrast. Function keys shall contrast visually from
background surfaces. Characters and symbols on key surfaces shall
contrast visually from key surfaces. Visual contrast shall be either
light-on-dark or dark-on-light.
EXCEPTION: Tactile symbols required by 707.6.3.2 shall not be
required to comply with 707.6.3.1.
707.6.3.2 Tactile Symbols. Function key surfaces shall have
tactile symbols as follows: Enter or Proceed key: raised circle;
Clear or Correct key: raised left arrow; Cancel key: raised letter
ex; Add Value key: raised plus sign; Decrease Value key: raised
minus sign.
707.7 Display Screen. The display screen shall comply with
707.7.
EXCEPTION: Drive-up only automatic teller machines and fare
machines shall not be required to comply with 707.7.1.
707.7.1 Visibility. The display screen shall be visible from a
point located 40 inches (1015 mm) above the center of the clear
floor space in front of the machine.
707.7.2 Characters. Characters displayed on the screen shall be
in a sans serif font. Characters shall be \3/16\ inch (4.8 mm) high
minimum based on the uppercase letter ``I''. Characters shall
contrast with their background with either light characters on a
dark background or dark characters on a light background.
707.8 Braille Instructions. Braille instructions for initiating
the speech mode shall be provided. Braille shall comply with 703.3.

708 Two-Way Communication Systems

708.1 General. Two-way communication systems shall comply with
708.
708.2 Audible and Visual Indicators. The system shall provide
both audible and visual signals.
708.3 Handsets. Handset cords, if provided, shall be 29 inches
(735 mm) long minimum.
708.4 Residential Dwelling Unit Communication Systems.
Communications systems between a residential dwelling unit and a
site, building, or floor entrance shall comply with 708.4.
708.4.1 Common Use or Public Use System Interface. The common
use or public use system interface shall include the capability of
supporting voice and TTY communication with the residential dwelling
unit interface.
708.4.2 Residential Dwelling Unit Interface. The residential
dwelling unit system interface shall include a telephone jack
capable of supporting voice and TTY communication with the common
use or public use system interface.

CHAPTER 8: SPECIAL ROOMS, SPACES, AND ELEMENTS

801 General

801.1 Scope. The provisions of Chapter 8 shall apply where
required by Chapter 2 or where referenced by a requirement in this
document.

802 Wheelchair Spaces, Companion Seats, and Designated Aisle Seats

802.1 Wheelchair Spaces. Wheelchair spaces shall comply with
802.1.
802.1.1 Floor or Ground Surface. The floor or ground surface of
wheelchair spaces shall comply with 302. Changes in level are not
permitted.
EXCEPTION: Slopes not steeper than 1:48 shall be permitted.
802.1.2 Width. A single wheelchair space shall be 36 inches (915
mm) wide minimum. Where two adjacent wheelchair spaces are

[[Page 59541]]

provided, each wheelchair space shall be 33 inches (840 mm) wide
minimum.
802.1.3 Depth. Where a wheelchair space can be entered from the
front or rear, the wheelchair space shall be 48 inches (1220 mm)
deep minimum. Where a wheelchair space can be entered only from the
side, the wheelchair space shall be 60 inches (1525 mm) deep
minimum.
802.1.4 Approach. Wheelchair spaces shall adjoin accessible
routes. Accessible routes shall not overlap wheelchair spaces.
802.1.5 Overlap. Wheelchair spaces shall not overlap circulation
paths.
802.2 Lines of Sight. Lines of sight to the screen, performance
area, or playing field for spectators in wheelchair spaces shall
comply with 802.2.
802.2.1 Lines of Sight Over Seated Spectators. Where spectators
are expected to remain seated during events, spectators in
wheelchair spaces shall be afforded lines of sight complying with
802.2.1.
802.2.1.1 Lines of Sight Over Heads. Where spectators are
provided lines of sight over the heads of spectators seated in the
first row in front of their seats, spectators seated in wheelchair
spaces shall be afforded lines of sight over the heads of seated
spectators in the first row in front of wheelchair spaces.
802.2.1.2 Lines of Sight Between Heads. Where spectators are
provided lines of sight over the shoulders and between the heads of
spectators seated in the first row in front of their seats,
spectators seated in wheelchair spaces shall be afforded lines of
sight over the shoulders and between the heads of seated spectators
in the first row in front of wheelchair spaces.
802.2.2 Lines of Sight Over Standing Spectators. Where
spectators are expected to stand during events, spectators in
wheelchair spaces shall be afforded lines of sight complying with
802.2.2.
802.2.2.1 Lines of Sight Over Heads. Where standing spectators
are provided lines of sight over the heads of spectators standing in
the first row in front of their seats, spectators seated in
wheelchair spaces shall be afforded lines of sight over the heads of
standing spectators in the first row in front of wheelchair spaces.
802.2.2.2 Lines of Sight Between Heads. Where standing
spectators are provided lines of sight over the shoulders and
between the heads of spectators standing in the first row in front
of their seats, spectators seated in wheelchair spaces shall be
afforded lines of sight over the shoulders and between the heads of
standing spectators in the first row in front of wheelchair spaces.
802.3 Companion Seats. Companion seats shall comply with 802.3.
802.3.1 Alignment. In row seating, companion seats shall be
located to provide shoulder alignment with adjacent wheelchair
spaces. The shoulder alignment point of the wheelchair space shall
be measured 36 inches (915 mm) from the front of the wheelchair
space. The floor surface of the companion seat shall be at the same
elevation as the floor surface of the wheelchair space.
802.3.2 Type. Companion seats shall be equivalent in size,
quality, comfort, and amenities to the seating in the immediate
area. Companion seats shall be permitted to be movable.
802.4 Designated Aisle Seats. Designated aisle seats shall
comply with 802.4.
802.4.1 Armrests. Where armrests are provided on the seating in
the immediate area, folding or retractable armrests shall be
provided on the aisle side of the seat.
802.4.2 Identification. Each designated aisle seat shall be
identified by a sign or marker.

803 Dressing, Fitting, and Locker Rooms

803.1 General. Dressing, fitting, and locker rooms shall comply
with 803.
803.2 Turning Space. Turning space complying with 304 shall be
provided within the room.
803.3 Door Swing. Doors shall not swing into the room unless a
clear floor or ground space complying with 305.3 is provided beyond
the arc of the door swing.
803.4 Benches. A bench complying with 903 shall be provided
within the room.
803.5 Coat Hooks and Shelves. Coat hooks provided within the
room shall be located within one of the reach ranges specified in
308. Shelves shall be 40 inches (1015 mm) minimum and 48 inches
(1220 mm) maximum above the finish floor or ground.

804 Kitchens and Kitchenettes

804.1 General. Kitchens and kitchenettes shall comply with 804.
804.2 Clearance. Where a pass through kitchen is provided,
clearances shall comply with 804.2.1. Where a U-shaped kitchen is
provided, clearances shall comply with 804.2.2.
EXCEPTION: Spaces that do not provide a cooktop or conventional
range shall not be required to comply with 804.2.
804.2.1 Pass Through Kitchen. In pass through kitchens where
counters, appliances or cabinets are on two opposing sides, or where
counters, appliances or cabinets are opposite a parallel wall,
clearance between all opposing base cabinets, counter tops,
appliances, or walls within kitchen work areas shall be 40 inches
(1015 mm) minimum. Pass through kitchens shall have two entries.
804.2.2 U-Shaped. In U-shaped kitchens enclosed on three
contiguous sides, clearance between all opposing base cabinets,
counter tops, appliances, or walls within kitchen work areas shall
be 60 inches (1525 mm) minimum.
804.3 Kitchen Work Surface. In residential dwelling units
required to comply with 809, at least one 30 inches (760 mm) wide
minimum section of counter shall provide a kitchen work surface that
complies with 804.3.
804.3.1 Clear Floor or Ground Space. A clear floor space
complying with 305 positioned for a forward approach shall be
provided. The clear floor or ground space shall be centered on the
kitchen work surface and shall provide knee and toe clearance
complying with 306.
EXCEPTION: Cabinetry shall be permitted under the kitchen work
surface provided that all of the following conditions are met:
(a) The cabinetry can be removed without removal or replacement
of the kitchen work surface;
(b) the finish floor extends under the cabinetry; and
(c) the walls behind and surrounding the cabinetry are finished.
804.3.2 Height. The kitchen work surface shall be 34 inches (865
mm) maximum above the finish floor or ground.
EXCEPTION: A counter that is adjustable to provide a kitchen
work surface at variable heights, 29 inches (735 mm) minimum and 36
inches (915 mm) maximum, shall be permitted.
804.3.3 Exposed Surfaces. There shall be no sharp or abrasive
surfaces under the work surface counters.
804.4 Sinks. Sinks shall comply with 606.
804.5 Storage. At least 50 percent of shelf space in storage
facilities shall comply with 811.
804.6 Appliances. Where provided, kitchen appliances shall
comply with 804.6.
804.6.1 Clear Floor or Ground Space. A clear floor or ground
space complying with 305 shall be provided at each kitchen
appliance. Clear floor or ground spaces shall be permitted to
overlap.
804.6.2 Operable Parts. All appliance controls shall comply with
309.
EXCEPTIONS: 1. Appliance doors and door latching devices shall
not be required to comply with 309.4.
2. Bottom-hinged appliance doors, when in the open position,
shall not be required to comply with 309.3.
804.6.3 Dishwasher. Clear floor or ground space shall be
positioned adjacent to the dishwasher door. The dishwasher door, in
the open position, shall not obstruct the clear floor or ground
space for the dishwasher or the sink.
804.6.4 Range or Cooktop. Where a forward approach is provided,
the clear floor or ground space shall provide knee and toe clearance
complying with 306. Where knee and toe space is provided, the
underside of the range or cooktop shall be insulated or otherwise
configured to prevent burns, abrasions, or electrical shock. The
location of controls shall not require reaching across burners.
804.6.5 Oven. Ovens shall comply with 804.6.5.
804.6.5.1 Side-Hinged Door Ovens. Side-hinged door ovens shall
have the work surface required by 804.3 positioned adjacent to the
latch side of the oven door.
804.6.5.2 Bottom-Hinged Door Ovens. Bottom-hinged door ovens
shall have the work surface required by 804.3 positioned adjacent to
one side of the door.
804.6.5.3 Controls. Ovens shall have controls on front panels.
804.6.6 Refrigerator/Freezer. Combination refrigerators and
freezers shall have at least 50 percent of the freezer space 54
inches (1370 mm) maximum above the finish floor or ground. The clear
floor or ground space shall be positioned for a parallel approach to
the space dedicated to a refrigerator/freezer with the centerline of
the clear floor or ground space offset 24 inches (610 mm) maximum
from the centerline of the dedicated space.

[[Page 59542]]

805 Medical Care and Long-Term Care Facilities

805.1 General. Medical care facility and long-term care facility
patient or resident sleeping rooms required to provide mobility
features shall comply with 805.
805.2 Turning Space. Turning space complying with 304 shall be
provided within the room.
805.3 Clear Floor or Ground Space. A clear floor space complying
with 305 shall be provided on each side of the bed. The clear floor
space shall be positioned for parallel approach to the side of the
bed.
805.4 Toilet and Bathing Rooms. Toilet and bathing rooms that
are provided as part of a patient or resident sleeping room shall
comply with 603. Where provided, no fewer than one water closet, one
lavatory, and one bathtub or shower shall comply with the applicable
requirements of 603 through 610.

806 Transient Lodging Guest Rooms

806.1 General. Transient lodging guest rooms shall comply with
806. Guest rooms required to provide mobility features shall comply
with 806.2. Guest rooms required to provide communication features
shall comply with 806.3.
806.2 Guest Rooms with Mobility Features. Guest rooms required
to provide mobility features shall comply with 806.2.
806.2.1 Living and Dining Areas. Living and dining areas shall
be accessible.
806.2.2 Exterior Spaces. Exterior spaces, including patios,
terraces and balconies, that serve the guest room shall be
accessible.
806.2.3 Sleeping Areas. At least one sleeping area shall provide
a clear floor space complying with 305 on both sides of a bed. The
clear floor space shall be positioned for parallel approach to the
side of the bed.
EXCEPTION: Where a single clear floor space complying with 305
positioned for parallel approach is provided between two beds, a
clear floor or ground space shall not be required on both sides of a
bed.
806.2.4 Toilet and Bathing Facilities. At least one bathroom
that is provided as part of a guest room shall comply with 603. No
fewer than one water closet, one lavatory, and one bathtub or shower
shall comply with applicable requirements of 603 through 610. In
addition, required roll-in shower compartments shall comply with
608.2.2 or 608.2.3. Toilet and bathing fixtures required to comply
with 603 through 610 shall be permitted to be located in more than
one toilet or bathing area, provided that travel between fixtures
does not require travel between other parts of the guest room.
806.2.4.1 Vanity Counter Top Space. If vanity counter top space
is provided in non-accessible guest toilet or bathing rooms,
comparable vanity counter top space, in terms of size and proximity
to the lavatory, shall also be provided in accessible guest toilet
or bathing rooms.
806.2.5 Kitchens and Kitchenettes. Kitchens and kitchenettes
shall comply with 804.
806.2.6 Turning Space. Turning space complying with 304 shall be
provided within the guest room.
806.3 Guest Rooms with Communication Features. Guest rooms
required to provide communication features shall comply with 806.3.
806.3.1 Alarms. Where emergency warning systems are provided,
alarms complying with 702 shall be provided.
806.3.2 Notification Devices. Visible notification devices shall
be provided to alert room occupants of incoming telephone calls and
a door knock or bell. Notification devices shall not be connected to
visible alarm signal appliances. Telephones shall have volume
controls compatible with the telephone system and shall comply with
704.3. Telephones shall be served by an electrical outlet complying
with 309 located within 48 inches (1220 mm) of the telephone to
facilitate the use of a TTY.

807 Holding Cells and Housing Cells

807.1 General. Holding cells and housing cells shall comply with
807.
807.2 Cells with Mobility Features. Cells required to provide
mobility features shall comply with 807.2.
807.2.1 Turning Space. Turning space complying with 304 shall be
provided within the cell.
807.2.2 Benches. Where benches are provided, at least one bench
shall comply with 903.
807.2.3 Beds. Where beds are provided, clear floor space
complying with 305 shall be provided on at least one side of the
bed. The clear floor space shall be positioned for parallel approach
to the side of the bed.
807.2.4 Toilet and Bathing Facilities. Toilet facilities or
bathing facilities that are provided as part of a cell shall comply
with 603. Where provided, no fewer than one water closet, one
lavatory, and one bathtub or shower shall comply with the applicable
requirements of 603 through 610.
807.3 Cells with Communication Features. Cells required to
provide communication features shall comply with 807.3.
807.3.1 Alarms. Where audible emergency alarm systems are
provided to serve the occupants of cells, visible alarms complying
with 702 shall be provided.
EXCEPTION: Visible alarms shall not be required where inmates or
detainees are not allowed independent means of egress.
807.3.2 Telephones. Telephones, where provided within cells,
shall have volume controls complying with 704.3.

808 Courtrooms

808.1 General. Courtrooms shall comply with 808.
808.2 Turning Space. Where provided, areas that are raised or
depressed and accessed by ramps or platform lifts with entry ramps
shall provide unobstructed turning space complying with 304.
808.3 Clear Floor Space. Each jury box and witness stand shall
have, within its defined area, clear floor space complying with 305.
EXCEPTION: In alterations, wheelchair spaces are not required to
be located within the defined area of raised jury boxes or witness
stands and shall be permitted to be located outside these spaces
where ramp or platform lift access poses a hazard by restricting or
projecting into a means of egress required by the appropriate
administrative authority.
808.4 Judges' Benches and Courtroom Stations. Judges' benches,
clerks' stations, bailiffs' stations, deputy clerks' stations, court
reporters' stations and litigants' and counsel stations shall comply
with 902.

809 Residential Dwelling Units

809.1 General. Residential dwelling units shall comply with 809.
Residential dwelling units required to provide mobility features
shall comply with 809.2 through 809.4. Residential dwelling units
required to provide communication features shall comply with 809.5.
809.2 Accessible Routes. Accessible routes complying with
Chapter 4 shall be provided within residential dwelling units in
accordance with 809.2.
EXCEPTION: Accessible routes shall not be required to or within
unfinished attics or unfinished basements.
809.2.1 Location. At least one accessible route shall connect
all spaces and elements which are a part of the residential dwelling
unit. Where only one accessible route is provided, it shall not pass
through bathrooms, closets, or similar spaces.
809.2.2 Turning Space. All rooms served by an accessible route
shall provide a turning space complying with 304.
EXCEPTION: Turning space shall not be required in exterior
spaces 30 inches (760 mm) maximum in depth or width.
809.3 Kitchen. Where a kitchen is provided, it shall comply with
804.
809.4 Toilet Facilities and Bathing Facilities. At least one
bathroom shall comply with 603. No fewer than one of each type of
fixture provided shall comply with applicable requirements of 603
through 610. Toilet and bathing fixtures required to comply with 603
through 610 shall be located in the same toilet and bathing area,
such that travel between fixtures does not require travel between
other parts of residential dwelling unit.
809.5 Residential Dwelling Units with Communication Features.
Residential dwelling units required to provide communication
features shall comply with 809.5.
809.5.1 Building Fire Alarm System. Where a building fire alarm
system is provided, the system wiring shall be extended to a point
within the residential dwelling unit in the vicinity of the
residential dwelling unit smoke detection system.
809.5.1.1 Alarm Appliances. Where alarm appliances are provided
within a residential dwelling unit as part of the building fire
alarm system, they shall comply with 702.
809.5.1.2 Activation. All visible alarm appliances provided
within the residential dwelling unit for building fire alarm
notification shall be activated upon activation of the building fire
alarm in the portion of the building containing the residential
dwelling unit.
809.5.2 Residential Dwelling Unit Smoke Detection System.
Residential dwelling unit smoke detection systems shall comply with
NFPA 72 (1999 or 2002 edition) (incorporated by reference, see
Referenced Standards'' in Chapter 1).

[[Page 59543]]

809.5.2.1 Activation. All visible alarm appliances provided
within the residential dwelling unit for smoke detection
notification shall be activated upon smoke detection.
809.5.3 Interconnection. The same visible alarm appliances shall
be permitted to provide notification of residential dwelling unit
smoke detection and building fire alarm activation.
809.5.4 Prohibited Use. Visible alarm appliances used to
indicate residential dwelling unit smoke detection or building fire
alarm activation shall not be used for any other purpose within the
residential dwelling unit.
809.5.5 Residential Dwelling Unit Primary Entrance.
Communication features shall be provided at the residential dwelling
unit primary entrance complying with 809.5.5.
809.5.5.1 Notification. A hardwired electric doorbell shall be
provided. A button or switch shall be provided outside the
residential dwelling unit primary entrance. Activation of the button
or switch shall initiate an audible tone and visible signal within
the residential dwelling unit. Where visible doorbell signals are
located in sleeping areas, they shall have controls to deactivate
the signal.
809.5.5.2 Identification. A means for visually identifying a
visitor without opening the residential dwelling unit entry door
shall be provided and shall allow for a minimum 180 degree range of
view.
809.5.6 Site, Building, or Floor Entrance. Where a system,
including a closed-circuit system, permitting voice communication
between a visitor and the occupant of the residential dwelling unit
is provided, the system shall comply with 708.4.

810 Transportation Facilities

810.1 General. Transportation facilities shall comply with 810.
810.2 Bus Boarding and Alighting Areas. Bus boarding and
alighting areas shall comply with 810.2.
810.2.1 Surface. Bus stop boarding and alighting areas shall
have a firm, stable surface.
810.2.2 Dimensions. Bus stop boarding and alighting areas shall
provide a clear length of 96 inches (2440 mm) minimum, measured
perpendicular to the curb or vehicle roadway edge, and a clear width
of 60 inches (1525 mm) minimum, measured parallel to the vehicle
roadway.
810.2.3 Connection. Bus stop boarding and alighting areas shall
be connected to streets, sidewalks, or pedestrian paths by an
accessible route complying with 402.
810.2.4 Slope. Parallel to the roadway, the slope of the bus
stop boarding and alighting area shall be the same as the roadway,
to the maximum extent practicable. Perpendicular to the roadway, the
slope of the bus stop boarding and alighting area shall not be
steeper than 1:48.
810.3 Bus Shelters. Bus shelters shall provide a minimum clear
floor or ground space complying with 305 entirely within the
shelter. Bus shelters shall be connected by an accessible route
complying with 402 to a boarding and alighting area complying with
810.2.
810.4 Bus Signs. Bus route identification signs shall comply
with 703.5.1 through 703.5.4, and 703.5.7 and 703.5.8. In addition,
to the maximum extent practicable, bus route identification signs
shall comply with 703.5.5.
EXCEPTION: Bus schedules, timetables and maps that are posted at
the bus stop or bus bay shall not be required to comply.
810.5 Rail Platforms. Rail platforms shall comply with 810.5.
810.5.1 Slope. Rail platforms shall not exceed a slope of 1:48
in all directions.
EXCEPTION: Where platforms serve vehicles operating on existing
track or track laid in existing roadway, the slope of the platform
parallel to the track shall be permitted to be equal to the slope
(grade) of the roadway or existing track.
810.5.2 Detectable Warnings. Platform boarding edges not
protected by platform screens or guards shall have detectable
warnings complying with 705 along the full length of the public use
area of the platform.
810.5.3 Platform and Vehicle Floor Coordination. Station
platforms shall be positioned to coordinate with vehicles in
accordance with the applicable requirements of 36 CFR Part 1192.
Low-level platforms shall be 8 inches (205 mm) minimum above top of
rail.
EXCEPTION: Where vehicles are boarded from sidewalks or street-
level, low-level platforms shall be permitted to be less than 8
inches (205 mm).
810.6 Rail Station Signs. Rail station signs shall comply with
810.6.
EXCEPTION. Signs shall not be required to comply with 810.6.1
and 810.6.2 where audible signs are remotely transmitted to hand-
held receivers, or are user- or proximity-actuated.
810.6.1 Entrances. Where signs identify a station or its
entrance, at least one sign at each entrance shall comply with 703.2
and shall be placed in uniform locations to the maximum extent
practicable. Where signs identify a station that has no defined
entrance, at least one sign shall comply with 703.2 and shall be
placed in a central location.
810.6.2 Routes and Destinations. Lists of stations, routes and
destinations served by the station which are located on boarding
areas, platforms, or mezzanines shall comply with 703.5. At least
one tactile sign identifying the specific station and complying with
703.2 shall be provided on each platform or boarding area. Signs
covered by this requirement shall, to the maximum extent
practicable, be placed in uniform locations within the system.
EXCEPTION: Where sign space is limited, characters shall not be
required to exceed 3 inches (75 mm).
810.6.3 Station Names. Stations covered by this section shall
have identification signs complying with 703.5. Signs shall be
clearly visible and within the sight lines of standing and sitting
passengers from within the vehicle on both sides when not obstructed
by another vehicle.
810.7 Public Address Systems. Where public address systems
convey audible information to the public, the same or equivalent
information shall be provided in a visual format.
810.8 Clocks. Where clocks are provided for use by the public,
the clock face shall be uncluttered so that its elements are clearly
visible. Hands, numerals and digits shall contrast with the
background either light-on-dark or dark-on-light. Where clocks are
installed overhead, numerals and digits shall comply with 703.5.
810.9 Escalators. Where provided, escalators shall comply with
the sections 6.1.3.5.6 and 6.1.3.6.5 of ASME A17.1 (incorporated by
reference, see Referenced Standards'' in Chapter 1) and shall have a
clear width of 32 inches (815 mm) minimum.
EXCEPTION: Existing escalators in key stations shall not be
required to comply with 810.9.
810.10 Track Crossings. Where a circulation path serving
boarding platforms crosses tracks, it shall comply with 402.
EXCEPTION: Openings for wheel flanges shall be permitted to be
2\1/2\ inches (64 mm) maximum.

811 Storage

811.1 General. Storage shall comply with 811.
811.2 Clear Floor or Ground Space. A clear floor or ground space
complying with 305 shall be provided.
811.3 Height. Storage elements shall comply with at least one of
the reach ranges specified in 308.
811.4 Operable Parts. Operable parts shall comply with 309.

Chapter 9: Built-in Elements

901 General

901.1 Scope. The provisions of Chapter 9 shall apply where
required by Chapter 2 or where referenced by a requirement in this
document.

902 Dining Surfaces and Work Surfaces

902.1 General. Dining surfaces and work surfaces shall comply
with 902.2 and 902.3.
EXCEPTION: Dining surfaces and work surfaces for children's use
shall be permitted to comply with 902.4.
902.2 Clear Floor or Ground Space. A clear floor space complying
with 305 positioned for a forward approach shall be provided. Knee
and toe clearance complying with 306 shall be provided.
902.3 Height. The tops of dining surfaces and work surfaces
shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum
above the finish floor or ground.
902.4 Dining Surfaces and Work Surfaces for Children's Use.
Accessible dining surfaces and work surfaces for children's use
shall comply with 902.4.
EXCEPTION: Dining surfaces and work surfaces that are used
primarily by children 5 years and younger shall not be required to
comply with 902.4 where a clear floor or ground space complying with
305 positioned for a parallel approach is provided.
902.4.1 Clear Floor or Ground Space. A clear floor space
complying with 305 positioned for forward approach shall be
provided. Knee and toe clearance complying with 306 shall be
provided, except that knee clearance 24 inches (610 mm) minimum
above the finish floor or ground shall be permitted.

[[Page 59544]]

902.4.2 Height. The tops of tables and counters shall be 26
inches (660 mm) minimum and 30 inches (760 mm) maximum above the
finish floor or ground.

903 Benches

903.1 General. Benches shall comply with 903.
903.2 Clear Floor or Ground Space. Clear floor or ground space
complying with 305 shall be provided and shall be positioned at the
end of the bench seat and parallel to the short axis of the bench.
903.3 Size. Benches shall have seats that are 42 inches (1065
mm) long minimum and 20 inches (510 mm) deep minimum and 24 inches
(610 mm) deep maximum.
903.4 Back Support. The bench shall provide for back support or
shall be affixed to a wall. Back support shall be 42 inches (1065
mm) long minimum and shall extend from a point 2 inches (51 mm)
maximum above the seat surface to a point 18 inches (455 mm) minimum
above the seat surface. Back support shall be 2\1/2\ inches (64 mm)
maximum from the rear edge of the seat measured horizontally.
903.5 Height. The top of the bench seat surface shall be 17
inches (430 mm) minimum and 19 inches (485 mm) maximum above the
finish floor or ground.
903.6 Structural Strength. Allowable stresses shall not be
exceeded for materials used when a vertical or horizontal force of
250 pounds (1112 N) is applied at any point on the seat, fastener,
mounting device, or supporting structure.
903.7 Wet Locations. Where installed in wet locations, the
surface of the seat shall be slip resistant and shall not accumulate
water.

904 Check-Out Aisles and Sales and Service Counters

904.1 General. Check-out aisles and sales and service counters
shall comply with the applicable requirements of 904.
904.2 Approach. All portions of counters required to comply with
904 shall be located adjacent to a walking surface complying with
403.
904.3 Check-Out Aisles. Check-out aisles shall comply with
904.3.
904.3.1 Aisle. Aisles shall comply with 403.
904.3.2 Counter. The counter surface height shall be 38 inches
(965 mm) maximum above the finish floor or ground. The top of the
counter edge protection shall be 2 inches (51 mm) maximum above the
top of the counter surface on the aisle side of the check-out
counter.
904.3.3 Check Writing Surfaces. Where provided, check writing
surfaces shall comply with 902.3.
904.4 Sales and Service Counters. Sales counters and service
counters shall comply with 904.4.1 or 904.4.2. The accessible
portion of the counter top shall extend the same depth as the sales
or service counter top.
EXCEPTION: In alterations, when the provision of a counter
complying with 904.4 would result in a reduction of the number of
existing counters at work stations or a reduction of the number of
existing mail boxes, the counter shall be permitted to have a
portion which is 24 inches (610 mm) long minimum complying with
904.4.1 provided that the required clear floor or ground space is
centered on the accessible length of the counter.
904.4.1 Parallel Approach. A portion of the counter surface that
is 36 inches (915 mm) long minimum and 36 inches (915 mm) high
maximum above the finish floor shall be provided. A clear floor or
ground space complying with 305 shall be positioned for a parallel
approach adjacent to the 36 inch (915 mm) minimum length of counter.
EXCEPTION: Where the provided counter surface is less than 36
inches (915 mm) long, the entire counter surface shall be 36 inches
(915 mm) high maximum above the finish floor.
904.4.2 Forward Approach. A portion of the counter surface that
is 30 inches (760 mm) long minimum and 36 inches (915 mm) high
maximum shall be provided. Knee and toe space complying with 306
shall be provided under the counter. A clear floor or ground space
complying with 305 shall be positioned for a forward approach to the
counter.
904.5 Food Service Lines. Counters in food service lines shall
comply with 904.5.
904.5.1 Self-Service Shelves and Dispensing Devices. Self-
service shelves and dispensing devices for tableware, dishware,
condiments, food and beverages shall comply with 308.
904.5.2 Tray Slides. The tops of tray slides shall be 28 inches
(710 mm) minimum and 34 inches (865 mm) maximum above the finish
floor or ground.
904.6 Security Glazing. Where counters or teller windows have
security glazing to separate personnel from the public, a method to
facilitate voice communication shall be provided. Telephone handset
devices, if provided, shall comply with 704.3.

Chapter 10: Recreation Facilities

1001 General

1001.1 Scope. The provisions of Chapter 10 shall apply where
required by Chapter 2 or where referenced by a requirement in this
document.

1002 Amusement Rides

1002.1 General. Amusement rides shall comply with 1002.
1002.2 Accessible Routes. Accessible routes serving amusement
rides shall comply with Chapter 4.
EXCEPTIONS: 1. In load or unload areas and on amusement rides,
where compliance with 405.2 is not structurally or operationally
feasible, ramp slope shall be permitted to be 1:8 maximum.
2. In load or unload areas and on amusement rides, handrails
provided along walking surfaces complying with 403 and required on
ramps complying with 405 shall not be required to comply with 505
where compliance is not structurally or operationally feasible.
1002.3 Load and Unload Areas. A turning space complying with
304.2 and 304.3 shall be provided in load and unload areas.
1002.4 Wheelchair Spaces in Amusement Rides. Wheelchair spaces
in amusement rides shall comply with 1002.4.
1002.4.1 Floor or Ground Surface. The floor or ground surface of
wheelchair spaces shall be stable and firm.
1002.4.2 Slope. The floor or ground surface of wheelchair spaces
shall have a slope not steeper than 1:48 when in the load and unload
position.
1002.4.3 Gaps. Floors of amusement rides with wheelchair spaces
and floors of load and unload areas shall be coordinated so that,
when amusement rides are at rest in the load and unload position,
the vertical difference between the floors shall be within plus or
minus \5/8\ inches (16 mm) and the horizontal gap shall be 3 inches
(75 mm) maximum under normal passenger load conditions.
EXCEPTION: Where compliance is not operationally or structurally
feasible, ramps, bridge plates, or similar devices complying with
the applicable requirements of 36 CFR 1192.83(c) shall be provided.
1002.4.4 Clearances. Clearances for wheelchair spaces shall
comply with 1002.4.4.
EXCEPTIONS: 1. Where provided, securement devices shall be
permitted to overlap required clearances.
2. Wheelchair spaces shall be permitted to be mechanically or
manually repositioned.
3. Wheelchair spaces shall not be required to comply with 307.4.
1002.4.4.1 Width and Length. Wheelchair spaces shall provide a
clear width of 30 inches (760 mm) minimum and a clear length of 48
inches (1220 mm) minimum measured to 9 inches (230 mm) minimum above
the floor surface.
1002.4.4.2 Side Entry. Where wheelchair spaces are entered only
from the side, amusement rides shall be designed to permit
sufficient maneuvering clearance for individuals using a wheelchair
or mobility aid to enter and exit the ride.
1002.4.4.3 Permitted Protrusions in Wheelchair Spaces. Objects
are permitted to protrude a distance of 6 inches (150 mm) maximum
along the front of the wheelchair space, where located 9 inches (230
mm) minimum and 27 inches (685 mm) maximum above the floor or ground
surface of the wheelchair space. Objects are permitted to protrude a
distance of 25 inches (635 mm) maximum along the front of the
wheelchair space, where located more than 27 inches (685 mm) above
the floor or ground surface of the wheelchair space.
1002.4.5 Ride Entry. Openings providing entry to wheelchair
spaces on amusement rides shall be 32 inches (815 mm) minimum clear.
1002.4.6 Approach. One side of the wheelchair space shall adjoin
an accessible route when in the load and unload position.
1002.4.7 Companion Seats. Where the interior width of the
amusement ride is greater than 53 inches (1345 mm), seating is
provided for more than one rider, and the wheelchair is not required
to be centered within the amusement ride, a companion seat shall be
provided for each wheelchair space.
1002.4.7.1 Shoulder-to-Shoulder Seating. Where an amusement ride
provides shoulder-to-shoulder seating, companion seats shall be
shoulder-to-shoulder with the adjacent wheelchair space.

[[Page 59545]]

EXCEPTION: Where shoulder-to-shoulder companion seating is not
operationally or structurally feasible, compliance with this
requirement shall be required to the maximum extent practicable.
1002.5 Amusement Ride Seats Designed for Transfer. Amusement
ride seats designed for transfer shall comply with 1002.5 when
positioned for loading and unloading.
1002.5.1 Clear Floor or Ground Space. A clear floor or ground
space complying with 305 shall be provided in the load and unload
area adjacent to the amusement ride seats designed for transfer.
1002.5.2 Transfer Height. The height of amusement ride seats
designed for transfer shall be 14 inches (355 mm) minimum and 24
inches (610 mm) maximum measured from the surface of the load and
unload area.
1002.5.3 Transfer Entry. Where openings are provided for
transfer to amusement ride seats, the openings shall provide
clearance for transfer from a wheelchair or mobility aid to the
amusement ride seat.
1002.5.4 Wheelchair Storage Space. Wheelchair storage spaces
complying with 305 shall be provided in or adjacent to unload areas
for each required amusement ride seat designed for transfer and
shall not overlap any required means of egress or accessible route.
1002.6 Transfer Devices for Use with Amusement Rides. Transfer
devices for use with amusement rides shall comply with 1002.6 when
positioned for loading and unloading.
1002.6.1 Clear Floor or Ground Space. A clear floor or ground
space complying with 305 shall be provided in the load and unload
area adjacent to the transfer device.
1002.6.2 Transfer Height. The height of transfer device seats
shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum
measured from the load and unload surface.
1002.6.3 Wheelchair Storage Space. Wheelchair storage spaces
complying with 305 shall be provided in or adjacent to unload areas
for each required transfer device and shall not overlap any required
means of egress or accessible route.

1003 Recreational Boating Facilities

1003.1 General. Recreational boating facilities shall comply
with 1003.
1003.2 Accessible Routes. Accessible routes serving recreational
boating facilities, including gangways and floating piers, shall
comply with Chapter 4 except as modified by the exceptions in
1003.2.
1003.2.1 Boat Slips. Accessible routes serving boat slips shall
be permitted to use the exceptions in 1003.2.1.
EXCEPTIONS: 1. Where an existing gangway or series of gangways
is replaced or altered, an increase in the length of the gangway
shall not be required to comply with 1003.2 unless required by
202.4.
2. Gangways shall not be required to comply with the maximum
rise specified in 405.6.
3. Where the total length of a gangway or series of gangways
serving as part of a required accessible route is 80 feet (24 m)
minimum, gangways shall not be required to comply with 405.2.
4. Where facilities contain fewer than 25 boat slips and the
total length of the gangway or series of gangways serving as part of
a required accessible route is 30 feet (9145 mm) minimum, gangways
shall not be required to comply with 405.2.
5. Where gangways connect to transition plates, landings
specified by 405.7 shall not be required.
6. Where gangways and transition plates connect and are required
to have handrails, handrail extensions shall not be required. Where
handrail extensions are provided on gangways or transition plates,
the handrail extensions shall not be required to be parallel with
the ground or floor surface.
7. The cross slope specified in 403.3 and 405.3 for gangways,
transition plates, and floating piers that are part of accessible
routes shall be measured in the static position.
8. Changes in level complying with 303.3 and 303.4 shall be
permitted on the surfaces of gangways and boat launch ramps.
1003.2.2 Boarding Piers at Boat Launch Ramps. Accessible routes
serving boarding piers at boat launch ramps shall be permitted to
use the exceptions in 1003.2.2.
EXCEPTIONS: 1. Accessible routes serving floating boarding piers
shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in
1003.2.1.
2. Where the total length of the gangway or series of gangways
serving as part of a required accessible route is 30 feet (9145 mm)
minimum, gangways shall not be required to comply with 405.2.
3. Where the accessible route serving a floating boarding pier
or skid pier is located within a boat launch ramp, the portion of
the accessible route located within the boat launch ramp shall not
be required to comply with 405.
1003.3 Clearances. Clearances at boat slips and on boarding
piers at boat launch ramps shall comply with 1003.3.
1003.3.1 Boat Slip Clearance. Boat slips shall provide clear
pier space 60 inches (1525 mm) wide minimum and at least as long as
the boat slips. Each 10 feet (3050 mm) maximum of linear pier edge
serving boat slips shall contain at least one continuous clear
opening 60 inches (1525 mm) wide minimum.
EXCEPTIONS: 1. Clear pier space shall be permitted to be 36
inches (915 mm) wide minimum for a length of 24 inches (610 mm)
maximum, provided that multiple 36 inch (915 mm) wide segments are
separated by segments that are 60 inches (1525 mm) wide minimum and
60 inches (1525 mm) long minimum.
2. Edge protection shall be permitted at the continuous clear
openings, provided that it is 4 inches (100 mm) high maximum and 2
inches (51 mm) wide maximum.
3. In existing piers, clear pier space shall be permitted to be
located perpendicular to the boat slip and shall extend the width of
the boat slip, where the facility has at least one boat slip
complying with 1003.3, and further compliance with 1003.3 would
result in a reduction in the number of boat slips available or
result in a reduction of the widths of existing slips.
1003.3.2 Boarding Pier Clearances. Boarding piers at boat launch
ramps shall provide clear pier space 60 inches (1525 mm) wide
minimum and shall extend the full length of the boarding pier. Every
10 feet (3050 mm) maximum of linear pier edge shall contain at least
one continuous clear opening 60 inches (1525 mm) wide minimum.
EXCEPTIONS: 1. The clear pier space shall be permitted to be 36
inches (915 mm) wide minimum for a length of 24 inches (610 mm)
maximum provided that multiple 36 inch (915 mm) wide segments are
separated by segments that are 60 inches (1525 mm) wide minimum and
60 inches (1525 mm) long minimum.
2. Edge protection shall be permitted at the continuous clear
openings provided that it is 4 inches (100 mm) high maximum and 2
inches (51 mm) wide maximum.

1004 Exercise Machines and Equipment

1004.1 Clear Floor Space. Exercise machines and equipment shall
have a clear floor space complying with 305 positioned for transfer
or for use by an individual seated in a wheelchair. Clear floor or
ground spaces required at exercise machines and equipment shall be
permitted to overlap.

1005 Fishing Piers and Platforms

1005.1 Accessible Routes. Accessible routes serving fishing
piers and platforms, including gangways and floating piers, shall
comply with Chapter 4.
EXCEPTIONS: 1. Accessible routes serving floating fishing piers
and platforms shall be permitted to use Exceptions 1, 2, 5, 6, 7 and
8 in 1003.2.1.
2. Where the total length of the gangway or series of gangways
serving as part of a required accessible route is 30 feet (9145 mm)
minimum, gangways shall not be required to comply with 405.2.
1005.2 Railings. Where provided, railings, guards, or handrails
shall comply with 1005.2.
1005.2.1 Height. At least 25 percent of the railings, guards, or
handrails shall be 34 inches (865 mm) maximum above the ground or
deck surface.
EXCEPTION: Where a guard complying with sections 1003.2.12.1 and
1003.2.12.2 of the International Building Code (2000 edition) or
sections 1012.2 and 1012.3 of the International Building Code (2003
edition) (incorporated by reference, see ``Referenced Standards'' in
Chapter 1) is provided, the guard shall not be required to comply
with 1005.2.1.
1005.2.1.1 Dispersion. Railings, guards, or handrails required
to comply with 1005.2.1 shall be dispersed throughout the fishing
pier or platform.
1005.3 Edge Protection. Where railings, guards, or handrails
complying with 1005.2 are provided, edge protection complying with
1005.3.1 or 1005.3.2 shall be provided.
1005.3.1 Curb or Barrier. Curbs or barriers shall extend 2
inches (51 mm) minimum above the surface of the fishing pier or
platform.
1005.3.2 Extended Ground or Deck Surface. The ground or deck
surface shall extend 12 inches (305 mm) minimum beyond the inside
face of the railing. Toe clearance shall be provided and shall be 30
inches (760 mm) wide minimum and 9 inches (230 mm)

[[Page 59546]]

minimum above the ground or deck surface beyond the railing.
1005.4 Clear Floor or Ground Space. At each location where there
are railings, guards, or handrails complying with 1005.2.1, a clear
floor or ground space complying with 305 shall be provided. Where
there are no railings, guards, or handrails, at least one clear
floor or ground space complying with 305 shall be provided on the
fishing pier or platform.
1005.5 Turning Space. At least one turning space complying with
304.3 shall be provided on fishing piers and platforms.

1006 Golf Facilities

1006.1 General. Golf facilities shall comply with 1006.
1006.2 Accessible Routes. Accessible routes serving teeing
grounds, practice teeing grounds, putting greens, practice putting
greens, teeing stations at driving ranges, course weather shelters,
golf car rental areas, bag drop areas, and course toilet rooms shall
comply with Chapter 4 and shall be 48 inches (1220 mm) wide minimum.
Where handrails are provided, accessible routes shall be 60 inches
(1525 mm) wide minimum.
EXCEPTION: Handrails shall not be required on golf courses.
Where handrails are provided on golf courses, the handrails shall
not be required to comply with 505.
1006.3 Golf Car Passages. Golf car passages shall comply with
1006.3.
1006.3.1 Clear Width. The clear width of golf car passages shall
be 48 inches (1220 mm) minimum.
1006.3.2 Barriers. Where curbs or other constructed barriers
prevent golf cars from entering a fairway, openings 60 inches (1525
mm) wide minimum shall be provided at intervals not to exceed 75
yards (69 m).
1006.4 Weather Shelters. A clear floor or ground space 60 inches
(1525 mm) minimum by 96 inches (2440 mm) minimum shall be provided
within weather shelters.

1007 Miniature Golf Facilities

1007.1 General. Miniature golf facilities shall comply with
1007.
1007.2 Accessible Routes. Accessible routes serving holes on
miniature golf courses shall comply with Chapter 4. Accessible
routes located on playing surfaces of miniature golf holes shall be
permitted to use the exceptions in 1007.2.
EXCEPTIONS: 1. Playing surfaces shall not be required to comply
with 302.2.
2. Where accessible routes intersect playing surfaces of holes,
a 1 inch (25 mm) maximum curb shall be permitted for a width of 32
inches (815 mm) minimum.
3. A slope not steeper than 1:4 for a 4 inch (100 mm) maximum
rise shall be permitted.
4. Ramp landing slopes specified by 405.7.1 shall be permitted
to be 1:20 maximum.
5. Ramp landing length specified by 405.7.3 shall be permitted
to be 48 inches (1220 mm) long minimum.
6. Ramp landing size specified by 405.7.4 shall be permitted to
be 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum.
7. Handrails shall not be required on holes. Where handrails are
provided on holes, the handrails shall not be required to comply
with 505.
1007.3 Miniature Golf Holes. Miniature golf holes shall comply
with 1007.3.
1007.3.1 Start of Play. A clear floor or ground space 48 inches
(1220 mm) minimum by 60 inches (1525 mm) minimum with slopes not
steeper than 1:48 shall be provided at the start of play.
1007.3.2 Golf Club Reach Range Area. All areas within holes
where golf balls rest shall be within 36 inches (915 mm) maximum of
a clear floor or ground space 36 inches (915 mm) wide minimum and 48
inches (1220 mm) long minimum having a running slope not steeper
than 1:20. The clear floor or ground space shall be served by an
accessible route.

1008 Play Areas

1008.1 General. Play areas shall comply with 1008.
1008.2 Accessible Routes. Accessible routes serving play areas
shall comply with Chapter 4 and 1008.2 and shall be permitted to use
the exceptions in 1008.2.1 through 1008.2.3. Where accessible routes
serve ground level play components, the vertical clearance shall be
80 inches high (2030 mm) minimum.
1008.2.1 Ground Level and Elevated Play Components. Accessible
routes serving ground level play components and elevated play
components shall be permitted to use the exceptions in 1008.2.1.
EXCEPTIONS: 1. Transfer systems complying with 1008.3 shall be
permitted to connect elevated play components except where 20 or
more elevated play components are provided no more than 25 percent
of the elevated play components shall be permitted to be connected
by transfer systems.
2. Where transfer systems are provided, an elevated play
component shall be permitted to connect to another elevated play
component as part of an accessible route.
1008.2.2 Soft Contained Play Structures. Accessible routes
serving soft contained play structures shall be permitted to use the
exception in 1008.2.2.
EXCEPTION: Transfer systems complying with 1008.3 shall be
permitted to be used as part of an accessible route.
1008.2.3 Water Play Components. Accessible routes serving water
play components shall be permitted to use the exceptions in
1008.2.3.
EXCEPTIONS: 1. Where the surface of the accessible route, clear
floor or ground spaces, or turning spaces serving water play
components is submerged, compliance with 302, 403.3, 405.2, 405.3,
and 1008.2.6 shall not be required.
2. Transfer systems complying with 1008.3 shall be permitted to
connect elevated play components in water.
1008.2.4 Clear Width. Accessible routes connecting play
components shall provide a clear width complying with 1008.2.4.
1008.2.4.1 Ground Level. At ground level, the clear width of
accessible routes shall be 60 inches (1525 mm) minimum.
EXCEPTIONS: 1. In play areas less than 1000 square feet (93
m\2\), the clear width of accessible routes shall be permitted to be
44 inches (1120 mm) minimum, if at least one turning space complying
with 304.3 is provided where the restricted accessible route exceeds
30 feet (9145 mm) in length.
2. The clear width of accessible routes shall be permitted to be
36 inches (915 mm) minimum for a distance of 60 inches (1525 mm)
maximum provided that multiple reduced width segments are separated
by segments that are 60 inches (1525 mm) wide minimum and 60 inches
(1525 mm) long minimum.
1008.2.4.2 Elevated. The clear width of accessible routes
connecting elevated play components shall be 36 inches (915 mm)
minimum.
EXCEPTIONS: 1. The clear width of accessible routes connecting
elevated play components shall be permitted to be reduced to 32
inches (815 mm) minimum for a distance of 24 inches (610 mm) maximum
provided that reduced width segments are separated by segments that
are 48 inches (1220 mm) long minimum and 36 inches (915 mm) wide
minimum.
2. The clear width of transfer systems connecting elevated play
components shall be permitted to be 24 inches (610 mm) minimum.
1008.2.5 Ramps. Within play areas, ramps connecting ground level
play components and ramps connecting elevated play components shall
comply with 1008.2.5.
1008.2.5.1 Ground Level. Ramp runs connecting ground level play
components shall have a running slope not steeper than 1:16.
1008.2.5.2 Elevated. The rise for any ramp run connecting
elevated play components shall be 12 inches (305 mm) maximum.
1008.2.5.3 Handrails. Where required on ramps serving play
components, the handrails shall comply with 505 except as modified
by 1008.2.5.3.
EXCEPTIONS: 1. Handrails shall not be required on ramps located
within ground level use zones.
2. Handrail extensions shall not be required.
1008.2.5.3.1 Handrail Gripping Surfaces. Handrail gripping
surfaces with a circular cross section shall have an outside
diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm)
maximum. Where the shape of the gripping surface is non-circular,
the handrail shall provide an equivalent gripping surface.
1008.2.5.3.2 Handrail Height. The top of handrail gripping
surfaces shall be 20 inches (510 mm) minimum and 28 inches (710 mm)
maximum above the ramp surface.
1008.2.6 Ground Surfaces. Ground surfaces on accessible routes,
clear floor or ground spaces, and turning spaces shall comply with
1008.2.6.
1008.2.6.1 Accessibility. Ground surfaces shall comply with ASTM
F1951 (incorporated by reference, see Referenced Standards'' in
Chapter 1). Ground surfaces shall be inspected and maintained
regularly and frequently to ensure continued compliance with ASTM
F1951.
1008.2.6.2 Use Zones. Ground surfaces located within use zones
shall comply with ASTM F1292 (1999 edition or 2004 edition)
(incorporated by reference, see ``Referenced Standards'' in Chapter
1).

[[Page 59547]]

1008.3 Transfer Systems. Where transfer systems are provided to
connect to elevated play components, transfer systems shall comply
with 1008.3.
1008.3.1 Transfer Platforms. Transfer platforms shall be
provided where transfer is intended from wheelchairs or other
mobility aids. Transfer platforms shall comply with 1008.3.1.
1008.3.1.1 Size. Transfer platforms shall have level surfaces 14
inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum.
1008.3.1.2 Height. The height of transfer platforms shall be 11
inches (280 mm) minimum and 18 inches (455 mm) maximum measured to
the top of the surface from the ground or floor surface.
1008.3.1.3 Transfer Space. A transfer space complying with 305.2
and 305.3 shall be provided adjacent to the transfer platform. The
48 inch (1220 mm) long minimum dimension of the transfer space shall
be centered on and parallel to the 24 inch (610 mm) long minimum
side of the transfer platform. The side of the transfer platform
serving the transfer space shall be unobstructed.
1008.3.1.4 Transfer Supports. At least one means of support for
transferring shall be provided.
1008.3.2 Transfer Steps. Transfer steps shall be provided where
movement is intended from transfer platforms to levels with elevated
play components required to be on accessible routes. Transfer steps
shall comply with 1008.3.2.
1008.3.2.1 Size. Transfer steps shall have level surfaces 14
inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum.
1008.3.2.2 Height. Each transfer step shall be 8 inches (205 mm)
high maximum.
1008.3.2.3 Transfer Supports. At least one means of support for
transferring shall be provided.
1008.4 Play Components. Ground level play components on
accessible routes and elevated play components connected by ramps
shall comply with 1008.4.
1008.4.1 Turning Space. At least one turning space complying
with 304 shall be provided on the same level as play components.
Where swings are provided, the turning space shall be located
immediately adjacent to the swing.
1008.4.2 Clear Floor or Ground Space. Clear floor or ground
space complying with 305.2 and 305.3 shall be provided at play
components.
1008.4.3 Play Tables. Where play tables are provided, knee
clearance 24 inches (610 mm) high minimum, 17 inches deep (430 mm)
minimum, and 30 inches (760 mm) wide minimum shall be provided. The
tops of rims, curbs, or other obstructions shall be 31 inches (785
mm) high maximum.
EXCEPTION: Play tables designed and constructed primarily for
children 5 years and younger shall not be required to provide knee
clearance where the clear floor or ground space required by 1008.4.2
is arranged for a parallel approach.
1008.4.4 Entry Points and Seats. Where play components require
transfer to entry points or seats, the entry points or seats shall
be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from
the clear floor or ground space.
EXCEPTION: Entry points of slides shall not be required to
comply with 1008.4.4.
1008.4.5 Transfer Supports. Where play components require
transfer to entry points or seats, at least one means of support for
transferring shall be provided.

1009 Swimming Pools, Wading Pools, and Spas

1009.1 General. Where provided, pool lifts, sloped entries,
transfer walls, transfer systems, and pool stairs shall comply with
1009.
1009.2 Pool Lifts. Pool lifts shall comply with 1009.2.
1009.2.1 Pool Lift Location. Pool lifts shall be located where
the water level does not exceed 48 inches (1220 mm).
EXCEPTIONS: 1. Where the entire pool depth is greater than 48
inches (1220 mm), compliance with 1009.2.1 shall not be required.
2. Where multiple pool lift locations are provided, no more than
one pool lift shall be required to be located in an area where the
water level is 48 inches (1220 mm) maximum.
1009.2.2 Seat Location. In the raised position, the centerline
of the seat shall be located over the deck and 16 inches (405 mm)
minimum from the edge of the pool. The deck surface between the
centerline of the seat and the pool edge shall have a slope not
steeper than 1:48.
1009.2.3 Clear Deck Space. On the side of the seat opposite the
water, a clear deck space shall be provided parallel with the seat.
The space shall be 36 inches (915 mm) wide minimum and shall extend
forward 48 inches (1220 mm) minimum from a line located 12 inches
(305 mm) behind the rear edge of the seat. The clear deck space
shall have a slope not steeper than 1:48.
1009.2.4 Seat Height. The height of the lift seat shall be
designed to allow a stop at 16 inches (405 mm) minimum to 19 inches
(485 mm) maximum measured from the deck to the top of the seat
surface when in the raised (load) position.
1009.2.5 Seat Width. The seat shall be 16 inches (405 mm) wide
minimum.
1009.2.6 Footrests and Armrests. Footrests shall be provided and
shall move with the seat. If provided, the armrest positioned
opposite the water shall be removable or shall fold clear of the
seat when the seat is in the raised (load) position.
EXCEPTION: Footrests shall not be required on pool lifts
provided in spas.
1009.2.7 Operation. The lift shall be capable of unassisted
operation from both the deck and water levels. Controls and
operating mechanisms shall be unobstructed when the lift is in use
and shall comply with 309.4.
1009.2.8 Submerged Depth. The lift shall be designed so that the
seat will submerge to a water depth of 18 inches (455 mm) minimum
below the stationary water level.
1009.2.9 Lifting Capacity. Single person pool lifts shall have a
weight capacity of 300 pounds. (136 kg) minimum and be capable of
sustaining a static load of at least one and a half times the rated
load.
1009.3 Sloped Entries. Sloped entries shall comply with 1009.3.
1009.3.1 Sloped Entries. Sloped entries shall comply with
Chapter 4 except as modified in 1109.3.1 through 1109.3.3.
EXCEPTION: Where sloped entries are provided, the surfaces shall
not be required to be slip resistant.
1009.3.2 Submerged Depth. Sloped entries shall extend to a depth
of 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below
the stationary water level. Where landings are required by 405.7, at
least one landing shall be located 24 inches (610 mm) minimum and 30
inches (760 mm) maximum below the stationary water level.
EXCEPTION: In wading pools, the sloped entry and landings, if
provided, shall extend to the deepest part of the wading pool.
1009.3.3 Handrails. At least two handrails complying with 505
shall be provided on the sloped entry. The clear width between
required handrails shall be 33 inches (840 mm) minimum and 38 inches
(965 mm) maximum.
EXCEPTIONS: 1. Handrail extensions specified by 505.10.1 shall
not be required at the bottom landing serving a sloped entry.
2. Where a sloped entry is provided for wave action pools,
leisure rivers, sand bottom pools, and other pools where user access
is limited to one area, the handrails shall not be required to
comply with the clear width requirements of 1009.3.3.
3. Sloped entries in wading pools shall not be required to
provide handrails complying with 1009.3.3. If provided, handrails on
sloped entries in wading pools shall not be required to comply with
505.
1009.4 Transfer Walls. Transfer walls shall comply with 1009.4.
1009.4.1 Clear Deck Space. A clear deck space of 60 inches (1525
mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper
than 1:48 shall be provided at the base of the transfer wall. Where
one grab bar is provided, the clear deck space shall be centered on
the grab bar. Where two grab bars are provided, the clear deck space
shall be centered on the clearance between the grab bars.
1009.4.2 Height. The height of the transfer wall shall be 16
inches (405 mm) minimum and 19 inches (485 mm) maximum measured from
the deck.
1009.4.3 Wall Depth and Length. The depth of the transfer wall
shall be 12 inches (305 mm) minimum and 16 inches (405 mm) maximum.
The length of the transfer wall shall be 60 inches (1525 mm) minimum
and shall be centered on the clear deck space.
1009.4.4 Surface. Surfaces of transfer walls shall not be sharp
and shall have rounded edges.
1009.4.5 Grab Bars. At least one grab bar complying with 609
shall be provided on the transfer wall. Grab bars shall be
perpendicular to the pool wall and shall extend the full depth of
the transfer wall. The top of the gripping surface shall be 4 inches
(100 mm) minimum and 6 inches (150 mm) maximum above transfer walls.
Where one grab bar is provided, clearance shall be 24 inches (610
mm) minimum on both sides of the grab bar. Where two grab bars are
provided, clearance between grab bars shall be 24 inches (610 mm)
minimum.

[[Page 59548]]

EXCEPTION: Grab bars on transfer walls shall not be required to
comply with 609.4.
1009.5 Transfer Systems. Transfer systems shall comply with
1009.5.
1009.5.1 Transfer Platform. A transfer platform shall be
provided at the head of each transfer system. Transfer platforms
shall provide 19 inches (485 mm) minimum clear depth and 24 inches
(610 mm) minimum clear width.
1009.5.2 Transfer Space. A transfer space of 60 inches (1525 mm)
minimum by 60 inches (1525 mm) minimum with a slope not steeper than
1:48 shall be provided at the base of the transfer platform surface
and shall be centered along a 24 inch (610 mm) minimum side of the
transfer platform. The side of the transfer platform serving the
transfer space shall be unobstructed.
1009.5.3 Height. The height of the transfer platform shall
comply with 1009.4.2.
1009.5.4 Transfer Steps. Transfer step height shall be 8 inches
(205 mm) maximum. The surface of the bottom tread shall extend to a
water depth of 18 inches (455 mm) minimum below the stationary water
level.
1009.5.5 Surface. The surface of the transfer system shall not
be sharp and shall have rounded edges.
1009.5.6 Size. Each transfer step shall have a tread clear depth
of 14 inches (355 mm) minimum and 17 inches (430 mm) maximum and
shall have a tread clear width of 24 inches (610 mm) minimum.
1009.5.7 Grab Bars. At least one grab bar on each transfer step
and the transfer platform or a continuous grab bar serving each
transfer step and the transfer platform shall be provided. Where a
grab bar is provided on each step, the tops of gripping surfaces
shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum
above each step and transfer platform. Where a continuous grab bar
is provided, the top of the gripping surface shall be 4 inches (100
mm) minimum and 6 inches (150 mm) maximum above the step nosing and
transfer platform. Grab bars shall comply with 609 and be located on
at least one side of the transfer system. The grab bar located at
the transfer platform shall not obstruct transfer.
EXCEPTION: Grab bars on transfer systems shall not be required
to comply with 609.4.
1009.6 Pool Stairs. Pool stairs shall comply with 1009.6.
1009.6.1 Pool Stairs. Pool stairs shall comply with 504.
EXCEPTION: Pool step riser heights shall not be required to be 4
inches (100 mm) high minimum and 7 inches (180 mm) high maximum
provided that riser heights are uniform.
1009.6.2 Handrails. The width between handrails shall be 20
inches (510 mm) minimum and 24 inches (610 mm) maximum. Handrail
extensions required by 505.10.3 shall not be required on pool
stairs.

1010 Shooting Facilities With Firing Positions

1010.1 Turning Space. A circular turning space 60 inches (1525
mm) diameter minimum with slopes not steeper than 1:48 shall be
provided at shooting facilities with firing positions.

1011 Outdoor Constructed Features

1011.1 General. All outdoor constructed features shall comply
with 1011.2 and 1011.3. Outdoor constructed features specified in
1011.4 through 1011.8 shall comply with those provisions, as
applicable.
1011.2 Clear Ground Space. A clear ground space complying with
1011.2 shall be provided at outdoor constructed features.
EXCEPTIONS: 1. Where individual outdoor constructed features are
altered and the ground surface is not altered, the clear ground
space shall not be required to comply with 1011.2.2 and 1011.2.3.
2. In alterations, when an entity determines that a condition in
1019 does not permit full compliance with a specific provision in
1011.2, the clear ground space shall comply with the provision to
the extent practicable.
1011.2.1 Size and Location. The size and location of the clear
ground space shall be in accordance with Table 1011.2.1. Unless
otherwise specified in Table 1011.2.1, one full unobstructed side of
the clear ground space shall adjoin or overlap an outdoor recreation
access route or a trail, as applicable, or another clear ground
space.

Table 1011.2.1--Clear Ground Space
------------------------------------------------------------------------
Outdoor constructed feature Minimum size and location
------------------------------------------------------------------------
Picnic tables................ 36 inches (915 mm) on all usable sides of
the table measured from the back edge of
the benches.
Fire rings, grills, 48 inches (1220 mm) by 48 inches (1220
fireplaces, and woodstoves. mm) on all usable sides of the fire
ring, grill, fireplace, and woodstove
Center the space on each usable side of
the grill, fireplace, and woodstove.
Trash and recycling 36 inches (915 mm) by 48 inches (1220 mm)
receptacles. positioned for forward approach to the
receptacle opening; or 30 inches (760
mm) by 60 inches (1525 mm) positioned
for a parallel approach to the
receptacle opening.
Water hydrants............... 72 inches (1830 mm) by 48 inches (1220
mm) with the long side of the space
adjoining or overlapping an outdoor
recreation access route or trail, as
applicable, or another clear ground
space.
Locate the space so that the water spout
is 11 inches (280 mm) minimum and 12
inches (305 mm) maximum from the rear
center of the long side of the space.
Utility and sewage hookups... 30 inches (760 mm) by 60 inches (1525 mm)
with the long side of the space
adjoining or overlapping an accessible
parking space or pull-up space for
recreational vehicles.
Locate the space so that the hook-ups are
at the rear center of the space.
Bollards or other barriers shall not
obstruct the clear ground space in front
of the hook-ups.
Outdoor rinsing showers...... 60 inches (1525 mm) by 60 inches (1525
mm) centered on the shower heads.
Locate the space so that the shower
pedestal or wall with the shower head
are at the rear end of the space.
Benches...................... 36 inches (915 mm) by 48 inches (1220 mm)
positioned near the bench with one side
of the space adjoining an outdoor
recreation access route or trail, as
applicable.
The clear ground space shall not overlap
the outdoor recreation access route or
trail, or another clear ground space.
Viewing Scopes............... 36 inches (915 mm) by 48 inches (1220 mm)
positioned for forward approach to the
viewing scope.
Provide knee and toe clearance complying
with 306 under the viewing scope.
Locate the space so that the eyepiece is
centered on the space.
------------------------------------------------------------------------

1011.2.2 Surface. The surface of the clear ground space shall be
firm and stable.
1011.2.3 Slope. The slope of the clear ground space surface
shall not be steeper than 1:48 in any direction.
EXCEPTION: Where the surface is other than asphalt, concrete, or
boards, slopes not steeper than 1:20 shall be permitted when
necessary for drainage.
1011.2.4 Openings. Openings in the clear ground space surface
shall not allow the passage of a sphere more than \1/2\ inch (13 mm)
in diameter.
1011.3 Operable Parts. Operable parts shall comply with 309.3
and 309.4.
EXCEPTIONS: 1. Fire rings, grills, fireplaces, wood stoves,
water hydrants, and water utility hookups shall comply with 309.4 to
the extent practicable.
2. Trash and recycling receptacles with hinged lids and controls
to keep out large animals shall comply with 309.4 to the extent
practicable.
3. Dumpster type trash and recycling receptacles shall not be
required to comply with 309.3 and 309.4.
4. Sewage hatches shall not be required to comply with 309.3 and
309.4.
1011.4 Picnic Tables. Picnic tables shall comply with 1011.4.
1011.4.1 Height. The tops of picnic tables shall comply with
902.3.

[[Page 59549]]

1011.4.2 Wheelchair Space. Picnic tables shall provide at least
one wheelchair space for each 24 linear feet (7320 mm) of usable
table surface perimeter. Wheelchair spaces shall be 30 inches (760
mm) minimum by 48 inches (1220 mm) minimum. Wheelchair spaces shall
be positioned for a forward approach to the table and provide knee
and toe clearance complying with 306 under the table.
1011.5 Fire Rings, Grills, Fireplaces, and Wood Stoves. Fire
rings, grills, fireplaces, and wood stoves shall comply with 1011.5.
1011.5.1 Fire Building Surfaces. Fire building surfaces shall be
9 inches (230 mm) minimum above the ground.
1011.5.2 Cooking Surfaces. Where provided, cooking surfaces
shall be 15 inches (380 mm) minimum and 34 inches (865 mm) maximum
above the ground.
1011.5.3 Raised Edges or Walls. Where fire rings, grills, or
fireplaces are constructed with raised edges or walls, the depth of
the raised edge or wall shall be 10 inches (255 mm) maximum.
1011.6 Water Spouts. Water spouts at water hydrants and water
utility hook-ups shall be 28 inches (710 mm) minimum and 36 inches
(915 mm) maximum above the ground.
1011.7 Outdoor Rinsing Showers. Outdoor rinsing showers shall
provide at least one hand-held shower spray unit with a hose 59
inches (1500 mm) long minimum. The hand-held shower spray unit shall
have at least one fixed position located 15 inches minimum (380 mm)
and 48 inches (1220 mm) maximum above the ground.
EXCEPTION: Where vandalism is a consideration, a fixed shower
head located at 48 in (1220 mm) above the ground shall be permitted
in place of a hand-held shower spray unit.
1011.8 Viewing Scopes. Eyepieces on viewing scopes shall be 43
inches (1090 mm) minimum and 51 inches (1295 mm) maximum above the
ground.

1012 Parking Spaces Within Camping Units and Picnic Units and Pull-up
Spaces at Dump Stations

1012.1 General. Parking spaces within camping units and picnic
units with mobility features and pull-up spaces for recreational
vehicles at dump stations shall comply with 1012.
1012.2 Recreational Vehicles. Parking spaces and pull-up spaces
for recreational vehicles shall be 20 feet (6100 mm) wide minimum.
EXCEPTION: Where two adjacent parking spaces are provided for
recreational vehicles, one parking space shall be permitted to be 16
feet (4880 mm) wide minimum.
1012.3 Other Vehicles. Parking spaces for vehicles, other than
recreational vehicles, shall be 16 feet (4880 mm) wide minimum.
EXCEPTION: Where two adjacent parking spaces are provided for
vehicles, other than recreational vehicles, one parking space shall
be permitted to be 8 feet (2440 mm) wide minimum.
1012.4 Surface. The surface of parking spaces and pull-up spaces
shall be firm and stable.
1012.5 Slope. The slope of the surface of parking spaces and
pull-up spaces shall not be steeper than 1:48 in any direction.
EXCEPTION: Where the surface is other than asphalt, concrete, or
boards, slopes not steeper than 1:20 shall be permitted when
necessary for drainage.

1013 Tent Pads and Tent Platforms

1013.1 General. Tent pads and tent platforms shall comply with
1013.
EXCEPTION: When an entity determines that a condition in 1019
does not permit full compliance with a specific provision in 1013,
the tent pad and tent platform shall comply with the provision to
the extent practicable.
1013.2 Clear Ground Space. Clear ground space complying with
1013.2 shall be provided on all usable sides of tent pads and tent
platforms.
1013.2.1 Size. The clear ground space shall be 48 inches (1220
mm) wide minimum.
1013.2.2 Surface. The surface of the clear ground space shall be
firm and stable. The surface shall allow use of tent stakes and
other tent securement devices.
1013.3 Slope. The slope of the surface of tent pads, tent
platforms, and clear ground spaces shall not be steeper than 1:48 in
any direction.
EXCEPTION: Where the surface is other than asphalt, concrete, or
boards, slopes not steeper than 1:20 shall be permitted where
necessary for drainage.
1013.4 Height. Tent platforms shall be 19 inches (485 mm) high
maximum measured from the clear ground space to the tent platform
surface.

1014 Camp Shelters

1014.1 General. Camp shelters shall comply with 1014.
EXCEPTIONS: 1. When an entity determines that a condition in
1019 does not permit full compliance with a specific provision in
1014, the camp shelter shall comply with the provision to the extent
practicable.
2. Camp shelters shall not be required to comply with 307.
1014.2 Entrance. Camp shelters shall provide an entrance
complying with 1014.2.1 or 1014.2.2.
1014.2.1 Transfer Access. Where transfer access is provided at
the entrance to a camp shelter, the entrance shall comply with
1014.2.1.
1014.2.1.1 Clear Ground Space. A clear ground space shall be
provided at the entrance to the camp shelter. The clear ground space
shall be 36 inches (915 mm) minimum by 48 inches (1220 mm) minimum
and shall be positioned for a parallel approach to the camp shelter.
One full unobstructed side of the clear ground space shall adjoin or
overlap an outdoor recreation access route or trail, as applicable,
or another clear ground space.
1014.2.1.1.1 Surface. The surface of the clear ground space
shall be firm and stable.
1014.2.1.1.2 Slope. The slope of the surface of the clear ground
space shall not be steeper than 1:48 in any direction.
EXCEPTION: Where the surface is other than asphalt, concrete, or
boards, slopes not steeper than 1:20 shall be permitted where
necessary for drainage.
1014.2.1.2 Floor Height. The camp shelter floor at the entrance
shall be 19 inches (485 mm) high maximum measured from the clear
ground space.
1014.2.2 Roll-in Access. Where roll-in access is provided at the
entrance to a camp shelter, the entrance shall comply with 1014.2.2.
1014.2.2.1 Level or Sloped Entry Route. Camp shelters providing
roll-in access shall have a level or sloped entry route complying
1016 or 1017, as applicable.
1014.2.2.2 Turning Space. A turning space complying with 304.3
shall be provided within the camp shelter.
1014.3 Floor. The floor within camp shelters shall comply with
1014.3.
1014.3.1 Surface. The floor surface shall be firm and stable.
1014.3.2 Slope. The slope of the floor surface shall not be
steeper than 1:48 in any direction.
EXCEPTION: Where the floor surface is other than asphalt,
concrete, or boards, slopes not steeper than 1:20 shall be permitted
when necessary for drainage.

1015 Viewing Areas

1015.1 General. Viewing areas shall comply with 1015.
EXCEPTION: In alterations, when an entity determines that a
condition in 1019 does not permit full compliance with a specific
provision in 1015, the viewing area shall comply with the provision
to the extent practicable.
1015.2 Clear Ground Space. A clear ground space shall be
provided at each distinct viewing location. The clear ground space
shall be 36 inches (915 mm) minimum by 48 inches (1220 mm) minimum
and shall be positioned for either a forward or parallel approach to
the viewing location. One full unobstructed side of the clear ground
space shall adjoin or overlap an outdoor recreation access route or
trail, as applicable, or another clear ground space.
1015.3 Viewing Space. Each distinct viewing location shall
provide a viewing space adjacent to the clear ground space required
by 1015.2 through which the point of interest is viewable. The
viewing space shall be 32 inches (815 mm) maximum and 51 inches
(1295 mm) minimum high above the ground and shall extend the full
width of the clear ground space.
EXCEPTION: Guards or similar safety barriers shall be permitted
to obstruct the viewing space to the extent the obstruction is
necessary for the guard or safety barrier to serve its intended
purpose.
1015.4 Turning Space. A turning space complying with 304.3 shall
be provided within viewing areas.
1015.5 Surface. The surface of clear ground spaces and turning
spaces shall be firm and stable.
1015.6 Slope. The slope of the surface of clear ground spaces
and turning spaces shall not be steeper than 1:48 in any direction.
EXCEPTION: Where the surface is other than asphalt, concrete, or
boards, slopes not steeper than 1:20 shall be permitted when
necessary for drainage.

[[Page 59550]]

1016 Outdoor Recreation Access Routes

1016.1 General. Outdoor recreation access routes shall comply
with 1016.
EXCEPTIONS: 1. In alterations to existing camping facilities,
picnic facilities, and trailheads, when an entity determines that a
condition in 1019 does not permit full compliance with a specific
provision in 1016 on a portion of an outdoor recreation access
route, the portion of the outdoor recreation access route shall
comply with the provision to the extent practicable.
2. At viewing areas, when an entity determines that a condition
in 1019 does not permit full compliance on a portion of an outdoor
recreation access route with a specific provision in 1016, the
portion of the outdoor recreation access route shall comply with the
provision to the extent practicable.
3. Where outdoor recreation access routes are provided within
vehicular ways, outdoor recreation access routes shall not be
required to comply with 1016.4, 1016.7, and 1016.8.
1016.2 Surface. The surface of outdoor recreation access routes,
passing spaces, and resting intervals shall be firm and stable.
1016.3 Clear Width. The clear width of outdoor recreation access
routes shall be 36 inches (915 mm) minimum.
1016.4 Passing Spaces. Outdoor recreation access routes with a
clear width less than 60 inches (1525 mm) shall provide passing
spaces complying with 1016.4 at intervals of 200 feet (61 m)
maximum. Passing spaces and resting intervals shall be permitted to
overlap.
1016.4.1 Size. The passing space shall be either:
1. A space 60 inches (1525 mm) minimum by 60 inches (1525 mm)
minimum; or
2. The intersection of two outdoor recreation access routes
providing a T-shaped space complying with 304.3.2 where the base and
the arms of the T-shaped space extend 48 inches (1220 mm) minimum
beyond the intersection. Vertical alignment at the intersection of
the outdoor recreation access routes that form the T-shaped space
shall be nominally planar.
1016.5 Obstacles. Obstacles on outdoor recreation access routes,
passing spaces, and resting intervals shall not exceed \1/2\ inch
(13 mm) in height measured vertically to the highest point.
EXCEPTION: Where the surface is other than asphalt, concrete, or
boards, obstacles shall be permitted to not exceed 1 inch (25 mm) in
height measured vertically to the highest point.
1016.6 Openings. Openings in the surface of outdoor recreation
access routes shall not allow the passage of a sphere more than \1/
2\ inch (13 mm) in diameter.
1016.7 Slopes. The slopes of outdoor recreation access routes
shall comply with 1016.7.
1016.7.1 Maximum Running Slope and Segment Length. The running
slope of any segment of an outdoor recreation access route shall not
be steeper than 1:10 (10%). Where the running slope of a segment of
an outdoor recreation access route is steeper than 1:20 (5%), the
maximum length of the segment shall be in accordance with Table
1016.7.1, and a resting interval complying with 1016.8 shall be
provided at the top and bottom of each segment.

Table 1016.7.1--Maximum Running Slope and Segment Length
------------------------------------------------------------------------
Running slope of outdoor recreation access route
segment
----------------------------------------------------- Maximum length of
But not steeper segment
Steeper than than
------------------------------------------------------------------------
1:20 (5%)....................... 1:12 (8.33%)...... 50 feet (15 m).
1:12 (8.33%).................... 1:10 (10%)........ 30 feet (9 m).
------------------------------------------------------------------------

1016.7.2 Cross Slope. The cross slope shall not be steeper than
1:48.
EXCEPTION: Where the surface is other than concrete, asphalt, or
boards, cross slopes not steeper than 1:20 shall be permitted when
necessary for drainage.
1016.8 Resting Intervals. Resting intervals shall comply with
1016.8.
1016.8.1 Length. The resting interval length shall be 60 inches
(1525 mm) long minimum.
1016.8.2 Width. Where resting intervals are provided within an
outdoor recreation access route, resting intervals shall be at least
as wide as the widest segment of the outdoor recreation access route
leading to the resting interval. Where resting intervals are
provided adjacent to an outdoor recreation access route, the resting
interval shall be 36 inches (915 mm) wide minimum.
1016.8.3 Slope. Resting intervals shall have slopes not steeper
than 1:48 in any direction.
EXCEPTION: Where the surface is other than concrete, asphalt, or
boards, slopes not steeper than 1:20 shall be permitted when
necessary for drainage.
1016.8.4 Turning Space. Where resting intervals are provided
adjacent to an outdoor recreation access route, a turning space
complying with 304.3.2 shall be provided. Vertical alignment between
the outdoor recreation access route, turning space, and resting
interval shall be nominally planar.
1016.9 Protruding Objects. Constructed elements on outdoor
recreation access routes, passing spaces, and resting intervals
shall comply with 307.

1017 Trails

1017.1 General. Trails shall comply with 1017.
EXCEPTIONS: 1. When an entity determines that a condition in
1019 does not permit full compliance with a specific provision in
1017 on a portion of a trail, the portion of the trail shall comply
with the provision to the extent practicable.
2. After applying Exception 1, when an entity determines that it
is impracticable for the entire trail to comply with 1017, the trail
shall not be required to comply with 1017.
1017.2 Surface. The surface of trails, passing spaces, and
resting intervals shall be firm and stable.
1017.3 Clear Tread Width. The clear tread width of trails shall
be 36 inches (915 mm) minimum.
1017.4 Passing Spaces. Trails with a clear tread width less than
60 inches (1525 mm) shall provide passing spaces complying with
1017.4 at intervals of 1000 feet (300 m) maximum. Where the full
length of a trail does not fully comply with 1017, a passing space
shall be located at the end of the trail segment that fully complies
with 1017. Passing spaces and resting intervals shall be permitted
to overlap.
1017.4.1 Size. The passing space shall be either:
1. A space 60 inches (1525 mm) minimum by 60 inches (1525 mm)
minimum; or
2. The intersection of two trails providing a T-shaped space
complying with 304.3.2 where the base and the arms of the T-shaped
space extend 48 inches (1220 mm) minimum beyond the intersection.
Vertical alignment at the intersection of the trails that form the
T-shaped space shall be nominally planar.
1017.5 Tread Obstacles. Tread obstacles on trails, passing
spaces, and resting intervals shall not exceed \1/2\ inch (13 mm) in
height measured vertically to the highest point.
EXCEPTION: Where the surface is other than asphalt, concrete, or
boards, tread obstacles shall be permitted to not exceed 2 inches
(50 mm) in height measured vertically to the highest point.
1017.6 Openings. Openings in the surface of trails, passing
spaces, and resting intervals shall not allow the passage of a
sphere more than \1/2\ inch (13 mm) in diameter.
1017.7 Slopes. The slopes of trails shall comply with 1017.7.
1017.7.1 Maximum Running Slope and Segment Length. Not more than
30 percent of the total length of a trail shall have a running slope
steeper than 1:12 (8.33%). The running slope of any segment of a
trail shall not be steeper than 1:8 (12%). Where the running slope
of a segment of a trail is steeper than 1:20 (5%), the maximum
length of the segment shall be in accordance with Table 1017.7.1,
and a resting interval complying with 1017.8 shall be provided at
the top and bottom of each segment.

[[Page 59551]]

Table 1017.7.1--Maximum Running Slope and Segment Length
------------------------------------------------------------------------
Running slope of trail segment
----------------------------------------------------- Maximum length of
But not steeper segment
Steeper than than
------------------------------------------------------------------------
1:20 (5%)....................... 1:12 (8.33%)...... 200 feet (61 m).
1:12 (8.33%).................... 1:10 (10%)........ 30 feet (9 m).
1:10 (10%)...................... 1:8 (12%)......... 10 feet (3050 mm).
------------------------------------------------------------------------

1017.7.2 Cross Slope. The cross slope shall be not be steeper
than 1:48.
EXCEPTION: Where the surface is other than concrete, asphalt, or
boards, cross slopes not steeper than 1:20 shall be permitted when
necessary for drainage.
1017.8 Resting Intervals. Resting intervals shall comply with
1017.8.
1017.8.1 Length. The resting interval length shall be 60 inches
(1525 mm) long minimum.
1017.8.2 Width. Where resting intervals are provided within the
trail tread, resting intervals shall be at least as wide as the
widest segment of the trail tread leading to the resting interval.
Where resting intervals are provided adjacent to the trail tread,
the resting interval clear width shall be 36 inches (915 mm)
minimum.
1017.8.3 Slope. Resting intervals shall have slopes not steeper
than 1:48 in any direction.
EXCEPTION: Where the surface is other than concrete, asphalt, or
boards, cross slopes not steeper than 1:20 shall be permitted when
necessary for drainage.
1017.8.4 Turning Space. Where resting intervals are provided
adjacent to the trail tread, a turning space complying with 304.3.2
shall be provided. Vertical alignment between the trail tread,
turning space, and resting interval shall be nominally planar.
1017.9 Protruding Objects. Constructed elements on trails,
passing spaces, and resting intervals shall comply with 307.
1017.10 Trailhead Signs. Trail information signs at trailheads
shall include the following:
1. Length of the trail or trail segment;
2. Surface type;
3. Typical and minimum tread width;
4. Typical and maximum running slope; and
5. Typical and maximum cross slope.

1018 Beach Access Routes

1018.1 General. Beach access routes shall comply with 1018.
EXCEPTIONS: 1. When an entity determines that a condition in
1019 does not permit full compliance with a specific provision in
1018 on a portion of a beach access route, the portion of the beach
access route shall comply with the provision to the extent
practicable.
2. After applying Exception 1, when an entity determines that it
is impracticable to provide a beach access route complying with
1018, a beach access route shall not be required.
3. Removable beach access routes shall not be required to comply
with 1018.7, 1018.8, and 1018.10.
1018.2 Connections. Beach access routes shall connect an entry
point to the beach to the:
1. High tide level at tidal beaches;
2. Mean high water level at river beaches; or
3. Normal recreation water level at lake, pond, and reservoir
beaches.
1018.3 Surface. The surface of beach access routes and resting
intervals shall be firm and stable.
1018.4 Clear Width. The clear width of beach access routes shall
be 60 inches (1525 mm) minimum.
EXCEPTION: At dune crossings, the clear width of beach access
routes that are not removable shall be permitted to be reduced to 48
inches (1220 mm) minimum.
1018.5 Obstacles. Obstacles on beach access routes and resting
intervals shall not exceed \1/2\ inch (13 mm) in height measured
vertically to the highest point.
EXCEPTION: Where the surface is other than asphalt, concrete, or
boards, obstacles shall be permitted to not exceed 1 inch (25 mm) in
height measured vertically to the highest point.
1018.6 Openings. Openings in the surface of beach access routes
and resting intervals shall not allow the passage of a sphere more
than \1/2\ inch (13 mm) in diameter.
1018.7 Slopes. The slopes of beach access routes shall comply
with 1018.7.
1018.7.1 Maximum Running Slope and Segment Length. The running
slope of any segment of a beach access route shall not be steeper
than 1:10 (10%). Where the running slope of a segment of a beach
access route is steeper than 1:20 (5%), the maximum length of the
segment shall be in accordance with Table 1018.7.1, and a resting
interval complying with 1018.8 shall be provided at the top and
bottom of each segment.

Table 1018.7.1--Maximum Running Slope and Segment Length
------------------------------------------------------------------------
Running slope of beach access route segment
----------------------------------------------------- Maximum length of
But not steeper segment
Steeper than than
------------------------------------------------------------------------
1:20 (5%)....................... 1:12 (8.33%)...... 50 feet (15 m).
1:12 (8.33%).................... 1:10 (10%)........ 30 feet (9 m).
------------------------------------------------------------------------

1018.7.2 Cross Slope. The cross slope shall not be steeper than
1:48.
EXCEPTION: Where the surface is other than concrete, asphalt, or
boards, cross slopes not steeper than 1:20 shall be permitted when
necessary for drainage.
1018.8 Resting Intervals. Resting intervals shall comply with
1018.8.
1018.8.1 Size. Resting intervals shall be 60 inches minimum
(1525 mm) by 60 inches (1525 mm) minimum.
1018.8.2 Slope. Resting intervals shall have a slope not steeper
than 1:48 in any direction.
EXCEPTION: Where the surface is other than concrete, asphalt, or
boards, cross slopes not steeper than 1:20 shall be permitted when
necessary for drainage.
1018.9 Protruding Objects. Constructed elements on beach access
routes and resting intervals shall comply with 307.
1018.10 Dune Crossings. Where the slope of a beach access route
at a dune crossing is steeper than 1:20 (5%), handrails complying
with 505 and curbs or barriers shall be provided. The curbs or
barriers shall prevent the passage of a 2 inch (50 mm) diameter
sphere, where any portion of the sphere is within 2 inches (50 mm)
of the crossing surface.

1019 Conditions for Exceptions

1019.1 General. Exceptions to specific provisions in 1011, 1013,
1014, 1015, 1016, 1017, and 1018 shall be permitted when an entity
determines that any of the following conditions does not permit full
compliance with the provision:
1. Compliance is not practicable due to terrain.
2. Compliance cannot be accomplished with the prevailing
construction practices.
3. Compliance would fundamentally alter the function or purpose
of the facility or the setting.
4. Compliance is limited or precluded by any of the following
laws, or by decisions or

[[Page 59552]]

opinions issued or agreements executed pursuant to any of the
following laws:
Endangered Species Act (16 U.S.C. 1531 et seq.);
National Environmental Policy Act (42 U.S.C. 4321 et
seq.);
National Historic Preservation Act (16 U.S.C. 470 et
seq.);
Wilderness Act (16 U.S.C. 1131 et seq.); or
Other federal, state, or local law the purpose of which
is to preserve threatened or endangered species; the environment; or
archaeological, cultural, historical, or other significant natural
features.
BILLING CODE 8150-01-P
[GRAPHIC] [TIFF OMITTED] TR26SE13.007

[[Page 59553]]

[GRAPHIC] [TIFF OMITTED] TR26SE13.008

APPENDIX E TO PART 1191 [Removed and Reserved]

0
8. Remove and reserve Appendix E to this part.

[FR Doc. 2013-22876 Filed 9-25-13; 8:45 am]
BILLING CODE 8150-01-C

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.