Airworthiness Directives; Fokker Services B.V. Airplanes, 46298-46301 [2013-18390]

Download as PDF ehiers on DSK2VPTVN1PROD with PROPOSALS-1 46298 Federal Register / Vol. 78, No. 147 / Wednesday, July 31, 2013 / Proposed Rules not cause the autothrust system to effect a transient response that alters the airplane’s flight path any greater than a minor transient, as defined in paragraph (l)(1) of this section. (d) Under normal conditions, the disengagement of any automatic control function of a flight guidance system may not cause a transient response of the airplane’s flight path any greater than a minor transient. (e) Under rare normal and non-normal conditions, disengagement of any automatic control function of a flight guidance system may not result in a transient any greater than a significant transient, as defined in paragraph (l)(2) of this section. (f) The function and direction of motion of each command reference control, such as heading select or vertical speed, must be plainly indicated on, or adjacent to, each control if necessary to prevent inappropriate use or confusion. (g) Under any condition of flight appropriate to its use, the flight guidance system may not produce hazardous loads on the airplane, nor create hazardous deviations in the flight path. This applies to both faultfree operation and in the event of a malfunction, and assumes that the pilot begins corrective action within a reasonable period of time. (h) When the flight guidance system is in use, a means must be provided to avoid excursions beyond an acceptable margin from the speed range of the normal flight envelope. If the airplane experiences an excursion outside this range, a means must be provided to prevent the flight guidance system from providing guidance or control to an unsafe speed. (i) The flight guidance system functions, controls, indications, and alerts must be designed to minimize flightcrew errors and confusion concerning the behavior and operation of the flight guidance system. Means must be provided to indicate the current mode of operation, including any armed modes, transitions, and reversions. Selector switch position is not an acceptable means of indication. The controls and indications must be grouped and presented in a logical and consistent manner. The indications must be visible to each pilot under all expected lighting conditions. (j) Following disengagement of the autothrust function, a caution (visual and auditory) must be provided to each pilot. (k) During autothrust operation, it must be possible for the flightcrew to move the thrust levers without requiring excessive force. The autothrust may not create a potential hazard when the flightcrew applies an override force to the thrust levers. (l) For purposes of this section, a transient is a disturbance in the control or flight path of the airplane that is not consistent with response to flightcrew inputs or environmental conditions. (1) A minor transient would not significantly reduce safety margins and would involve flightcrew actions that are well within their capabilities. A minor transient may involve a slight increase in flightcrew workload or some physical discomfort to passengers or cabin crew. VerDate Mar<15>2010 14:07 Jul 30, 2013 Jkt 229001 (2) A significant transient may lead to a significant reduction in safety margins, an increase in flightcrew workload, discomfort to the flightcrew, or physical distress to the passengers or cabin crew, possibly including non-fatal injuries. Significant transients do not require, in order to remain within or recover to the normal flight envelope, any of the following: (i) Exceptional piloting skill, alertness, or strength. (ii) Forces applied by the pilot which are greater than those specified in Sec. 23.143(c). (iii) Accelerations or attitudes in the airplane that might result in further hazard to secured or non-secured occupants. The applicant must also functionally demonstrate independence between the left and right ATS installation to prove they cannot have a single point failure that is not extremely improbable that inadvertently leads to a loss of thrust, or to substantial uncommanded thrust changes and transients, in both engines simultaneously. Issued in Kansas City, Missouri, on July 24, 2013. Earl Lawrence, Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 2013–18399 Filed 7–30–13; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2013–0629; Directorate Identifier 2012–NM–214–AD] RIN 2120–AA64 Airworthiness Directives; Fokker Services B.V. Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for certain Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This proposed AD was prompted by a design review, which revealed that under certain failure conditions of the maximum level (Max Level) sensor wiring, a short circuit may develop that causes a hot spot on the wiring conduit, or puncturing of the wiring conduit wall in the center wing fuel tank. This proposed AD would require installing fuses in the Max Level sensor wiring; and revising the airplane maintenance program by incorporating critical design configuration control limitations. We are proposing this AD to prevent an SUMMARY: PO 00000 Frm 00004 Fmt 4702 Sfmt 4702 ignition source in the center wing fuel tank vapor space, which could result in a fuel tank explosion and consequent loss of the airplane. DATES: We must receive comments on this proposed AD by September 16, 2013. ADDRESSES: You may send comments by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: (202) 493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Fokker Services B.V., Technical Services Dept., P.O. Box 1357, 2130 EL Hoofddorp, the Netherlands; telephone +31 (0)88–6280– 350; fax +31 (0)88–6280–111; email technicalservices@fokker.com; Internet https://www.myfokkerfleet.com. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the MCAI, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, Washington 98057–3356; telephone 425–227–1137; fax 425–227–1149. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments E:\FR\FM\31JYP1.SGM 31JYP1 Federal Register / Vol. 78, No. 147 / Wednesday, July 31, 2013 / Proposed Rules to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2013–0629; Directorate Identifier 2012–NM–214–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued EASA Airworthiness Directive 2012–0240, dated November 12, 2012 (referred to after this the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition for the specified products. The MCAI states: ehiers on DSK2VPTVN1PROD with PROPOSALS-1 Prompted by an accident * * *, the FAA published Special Federal Aviation Regulation (SFAR) 88, and the Joint Aviation Authorities (JAA) published Interim Policy INT/POL/25/12. The design review conducted by Fokker Services on the Fokker 70 and Fokker 100 in response to these regulations revealed that under certain failure conditions of the maximum level (Max Level) sensor wiring, a short circuit may develop that causes a hot spot on the wiring conduit, or puncturing of the wiring conduit wall in the tank. This condition, if not corrected, could create an ignition source in the centre tank vapour space, possibly resulting in a fuel tank explosion and consequent loss of the aeroplane. For the reasons described above, this [EASA] AD requires the installation of fuses in the Max Level sensor wiring and subsequently, the implementation of the associated Critical Design Configuration Control Limitations (CDCCL[s]) [by revising the maintenance program to incorporate the CDCCLs]. You may obtain further information by examining the MCAI in the AD docket. The FAA has examined the underlying safety issues involved in fuel tank explosions on several large transport airplanes, including the adequacy of existing regulations, the service history of airplanes subject to those regulations, and existing maintenance practices for fuel tank systems. As a result of those findings, we issued a regulation titled ‘‘Transport Airplane Fuel Tank System Design VerDate Mar<15>2010 14:07 Jul 30, 2013 Jkt 229001 Review, Flammability Reduction and Maintenance and Inspection Requirements’’ (66 FR 23086, May 7, 2001). In addition to new airworthiness standards for transport airplanes and new maintenance requirements, this rule included Special Federal Aviation Regulation No. 88 (‘‘SFAR 88,’’ Amendment 21–78, and subsequent Amendments 21–82 and 21–83). Among other actions, SFAR 88 (66 FR 23086, May 7, 2001) requires certain type design (i.e., type certificate (TC) and supplemental type certificate (STC)) holders to substantiate that their fuel tank systems can prevent ignition sources in the fuel tanks. This requirement applies to type design holders for large turbine-powered transport airplanes and for subsequent modifications to those airplanes. It requires them to perform design reviews and to develop design changes and maintenance procedures if their designs do not meet the new fuel tank safety standards. As explained in the preamble to the rule, we intended to adopt airworthiness directives to mandate any changes found necessary to address unsafe conditions identified as a result of these reviews. In evaluating these design reviews, we have established four criteria intended to define the unsafe conditions associated with fuel tank systems that require corrective actions. The percentage of operating time during which fuel tanks are exposed to flammable conditions is one of these criteria. The other three criteria address the failure types under evaluation: Single failures, single failures in combination with a latent condition(s), and in-service failure experience. For all four criteria, the evaluations included consideration of previous actions taken that may mitigate the need for further action. The Joint Aviation Authorities (JAA) has issued a regulation that is similar to SFAR 88 (66 FR 23086, May 7, 2001). (The JAA is an associated body of the European Civil Aviation Conference (ECAC) representing the civil aviation regulatory authorities of a number of European States who have agreed to cooperate in developing and implementing common safety regulatory standards and procedures.) Under this regulation, the JAA stated that all members of the ECAC that hold type certificates for transport category airplanes are required to conduct a design review against explosion risks. We have determined that the actions identified in this AD are necessary to reduce the potential of ignition sources inside fuel tanks, which, in combination PO 00000 Frm 00005 Fmt 4702 Sfmt 4702 46299 with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane. Relevant Service Information Fokker Services B.V. has issued Fokker Service Bulletin SBF100–28– 073, dated August 10, 2012, including the following attachments (* the issue date is not specified on the drawing) and manual change notification: • Fokker Drawing W41192, Sheet 052, Issue AS*; • Fokker Drawing W41192, Sheet 054, Issue AR*; • Fokker Drawing W59520, Sheet 003, Issue F, dated May 12, 2011; and • Fokker Manual Change Notification MCNM F100–150, dated August 10, 2012. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI. FAA’s Determination and Requirements of This Proposed AD This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design. This AD requires revisions to certain operator maintenance documents to include new Critical Design Configuration Control Limitations (CDCCLs). Compliance with these CDCCLs is required by 14 CFR 91.403(c). For airplanes that have been previously modified, altered, or repaired in the areas addressed by this AD, the operator may not be able to accomplish the actions described in the revisions. In this situation, to comply with 14 CFR 91.403(c), the operator must request approval for an alternative method of compliance according to paragraph (j) of this AD. The request should include a description of changes to the required actions that will ensure the continued operational safety of the airplane. Costs of Compliance We estimate that this proposed AD affects 10 products of U.S. registry. We estimate the following costs to comply with this proposed AD: E:\FR\FM\31JYP1.SGM 31JYP1 46300 Federal Register / Vol. 78, No. 147 / Wednesday, July 31, 2013 / Proposed Rules ESTIMATED COSTS Action Labor cost Parts cost Cost per product Cost on U.S. operators Installation and revision of maintenance program. 7 work-hours × $85 per hour = $595 ............. $2,100 $2,695 $26,950 Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. ehiers on DSK2VPTVN1PROD with PROPOSALS-1 Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); 3. Will not affect intrastate aviation in Alaska; and 4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. VerDate Mar<15>2010 14:07 Jul 30, 2013 Jkt 229001 The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new AD: ■ Fokker Services B.V.: Docket No. FAA– 2013–0629; Directorate Identifier 2012– NM–214–AD. (a) Comments Due Date We must receive comments by September 16, 2013. (b) Affected ADs None. (c) Applicability This AD applies to Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes, certificated in any category, equipped with a center wing fuel tank. (d) Subject Air Transport Association (ATA) of America Code 28, Fuel. (e) Reason This AD was prompted by a design review, which revealed that under certain failure conditions of the maximum level (Max Level) sensor wiring, a short circuit may develop that causes a hot spot on the wiring conduit, or puncturing of the wiring conduit wall in the center wing fuel tank. We are issuing this AD to prevent an ignition source in the center wing fuel tank vapor space, which could result in a fuel tank explosion and consequent loss of the airplane. (f) Compliance You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. (g) Installation of Fuses Within 24 months after the effective date of this AD: Do the actions specified in paragraphs (g)(1) and (g)(2) of this AD, as applicable. (1) For Fokker Services B.V. Model F.28 Mark 0070 airplanes having serial numbers 11244 through 11441 inclusive, equipped with a center wing bag tank: Install fuses in PO 00000 Frm 00006 Fmt 4702 Sfmt 4702 the wiring of the Max Level sensors of the center wing fuel tank, in accordance with Parts 1 and 3 of the Accomplishment Instructions of Fokker Service Bulletin SBF100–28–073, dated August 10, 2012, which includes the attachments identified in paragraphs (g)(1)(i) through (g)(1)(iv) of this AD (* the issue date is not specified on the drawing). (i) Fokker Drawing W41192, Sheet 052, Issue AS*. (ii) Fokker Drawing W41192, Sheet 054, Issue AR*. (iii) Fokker Drawing W59520, Sheet 003, Issue F, dated May 12, 2011. (iv) Fokker Manual Change Notification MCNM F100–150, dated August 10, 2012. (2) For Fokker Services B.V. Model F.28 Mark 0070 and Mark 0100 airplanes having serial numbers 11442 and up, equipped with an integral center wing tank: Install fuses in the wiring of the Max Level sensors of the center wing fuel tank, in accordance with Parts 2 and 3 of the Accomplishment Instructions of Fokker Service Bulletin SBF100–28–073, dated August 10, 2012, which includes the attachments identified in paragraphs (g)(2)(i) through (g)(2)(iv) of this AD (* the issue date is not specified on the drawing). (i) Fokker Drawing W41192, Sheet 052, Issue AS*. (ii) Fokker Drawing W41192, Sheet 054, Issue AR*. (iii) Fokker Drawing W59520, Sheet 003, Issue F, dated May 12, 2011. (iv) Fokker Manual Change Notification MCNM F100–150, dated August 10, 2012. (h) Revision of Maintenance or Inspection Program After doing any action required by paragraph (g) of this AD, before further flight, revise the airplane maintenance or inspection program, as applicable, by incorporating the CDCCLs specified in paragraph 1.L.(1)(c) of Fokker Service Bulletin SBF100–28–073, dated August 10, 2012, including the drawings specified in paragraphs (h)(1) through (h)(4) of this AD (* the issue date is not specified on the drawing) and manual change notification. (1) Fokker Drawing W41192, Sheet 052, Issue AS*. (2) Fokker Drawing W41192, Sheet 054, Issue AR*. (3) Fokker Drawing W59520, Sheet 003, Issue F, dated May 12, 2011. (4) Fokker Manual Change Notification MCNM F100–150, dated August 10, 2012. (i) No Alternative CDCCLs After the CDCCLs have been incorporated, as required by paragraph (h) of this AD, no alternative CDCCLs may be used unless the CDCCLs are approved as an alternative method of compliance (AMOC) in E:\FR\FM\31JYP1.SGM 31JYP1 Federal Register / Vol. 78, No. 147 / Wednesday, July 31, 2013 / Proposed Rules accordance with the procedures specified in paragraph (j) of this AD. DEPARTMENT OF TRANSPORTATION (j) Other FAA AD Provisions Federal Aviation Administration The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch; ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; telephone 425–227–1137; fax 425–227–1137. Information may be emailed to: 9-ANM-116AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The AMOC approval letter must specifically reference this AD. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (k) Related Information ehiers on DSK2VPTVN1PROD with PROPOSALS-1 (1) Refer to the Mandatory Continuing Airworthiness Information (MCAI) European Aviation Safety Agency Airworthiness Directive 2012–0240, dated November 12, 2012, for related information. The MCAI can be found in the AD docket on the Internet at https://regulations.gov. (2) For service information identified in this AD, contact Fokker Services B.V., Technical Services Dept., P.O. Box 1357, 2130 EL Hoofddorp, the Netherlands; telephone +31 (0)88–6280–350; fax +31 (0)88–6280–111; email technicalservices@fokker.com; Internet https://www.myfokkerfleet.com. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425 227–1221. Issued in Renton, Washington, on July 21, 2013. Stephen P. Boyd, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2013–18390 Filed 7–30–13; 8:45 am] BILLING CODE 4910–13–P VerDate Mar<15>2010 14:07 Jul 30, 2013 Jkt 229001 14 CFR Part 39 [Docket No. FAA–2013–0631; Directorate Identifier 2012–NM–142–AD] RIN 2120–AA64 Airworthiness Directives; BAE Systems (Operations) Limited Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model BAe 146 and Avro 146–RJ series airplanes. This proposed AD was prompted by a report of a cracked pickup bracket of the forward outboard pylon of the number 1 engine due to stress corrosion. This proposed AD would require repetitive inspections and, depending on findings, repair of the pylon pick-up brackets. We are proposing this AD to detect and correct cracking of the pick-up bracket, which could result in the engine pylon separating from the wing, with consequent damage to the airplane and reduced controllability. DATES: We must receive comments on this proposed AD by September 16, 2013. SUMMARY: You may send comments by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: (202) 493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact BAE Systems (Operations) Limited, Customer Information Department, Prestwick International Airport, Ayrshire, KA9 2RW, Scotland, United Kingdom; telephone +44 1292 675207; fax +44 1292 675704; email RApublications@ baesystems.com; Internet https:// www.baesystems.com/Businesses/ RegionalAircraft/index.htm. You may ADDRESSES: PO 00000 Frm 00007 Fmt 4702 Sfmt 4702 46301 review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057–3356; phone: (425)–1175; fax: (425)–1149. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2013–0631; Directorate Identifier 2012–NM–142–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued EASA Airworthiness Directive 2012–0136, dated July 20, 2012 (referred to after this as the Mandatory Continuing Airworthiness Information, or ‘‘the MCAI’’), to correct an unsafe condition for the specified products. The MCAI states: While carrying out a scheduled environmental inspection, an operator found E:\FR\FM\31JYP1.SGM 31JYP1

Agencies

[Federal Register Volume 78, Number 147 (Wednesday, July 31, 2013)]
[Proposed Rules]
[Pages 46298-46301]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2013-18390]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-0629; Directorate Identifier 2012-NM-214-AD]
RIN 2120-AA64


Airworthiness Directives; Fokker Services B.V. Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. 
This proposed AD was prompted by a design review, which revealed that 
under certain failure conditions of the maximum level (Max Level) 
sensor wiring, a short circuit may develop that causes a hot spot on 
the wiring conduit, or puncturing of the wiring conduit wall in the 
center wing fuel tank. This proposed AD would require installing fuses 
in the Max Level sensor wiring; and revising the airplane maintenance 
program by incorporating critical design configuration control 
limitations. We are proposing this AD to prevent an ignition source in 
the center wing fuel tank vapor space, which could result in a fuel 
tank explosion and consequent loss of the airplane.

DATES: We must receive comments on this proposed AD by September 16, 
2013.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Fokker Services B.V., Technical Services Dept., P.O. Box 1357, 2130 EL 
Hoofddorp, the Netherlands; telephone +31 (0)88-6280-350; fax +31 
(0)88-6280-111; email technicalservices@fokker.com; Internet https://www.myfokkerfleet.com. You may review copies of the referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the MCAI, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone (800) 
647-5527) is in the ADDRESSES section. Comments will be available in 
the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, Washington 98057-3356; telephone 425-227-
1137; fax 425-227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments

[[Page 46299]]

to an address listed under the ADDRESSES section. Include ``Docket No. 
FAA-2013-0629; Directorate Identifier 2012-NM-214-AD'' at the beginning 
of your comments. We specifically invite comments on the overall 
regulatory, economic, environmental, and energy aspects of this 
proposed AD. We will consider all comments received by the closing date 
and may amend this proposed AD based on those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
Airworthiness Directive 2012-0240, dated November 12, 2012 (referred to 
after this the Mandatory Continuing Airworthiness Information, or ``the 
MCAI''), to correct an unsafe condition for the specified products. The 
MCAI states:

    Prompted by an accident * * *, the FAA published Special Federal 
Aviation Regulation (SFAR) 88, and the Joint Aviation Authorities 
(JAA) published Interim Policy INT/POL/25/12.
    The design review conducted by Fokker Services on the Fokker 70 
and Fokker 100 in response to these regulations revealed that under 
certain failure conditions of the maximum level (Max Level) sensor 
wiring, a short circuit may develop that causes a hot spot on the 
wiring conduit, or puncturing of the wiring conduit wall in the 
tank.
    This condition, if not corrected, could create an ignition 
source in the centre tank vapour space, possibly resulting in a fuel 
tank explosion and consequent loss of the aeroplane.
    For the reasons described above, this [EASA] AD requires the 
installation of fuses in the Max Level sensor wiring and 
subsequently, the implementation of the associated Critical Design 
Configuration Control Limitations (CDCCL[s]) [by revising the 
maintenance program to incorporate the CDCCLs].

You may obtain further information by examining the MCAI in the AD 
docket.
    The FAA has examined the underlying safety issues involved in fuel 
tank explosions on several large transport airplanes, including the 
adequacy of existing regulations, the service history of airplanes 
subject to those regulations, and existing maintenance practices for 
fuel tank systems. As a result of those findings, we issued a 
regulation titled ``Transport Airplane Fuel Tank System Design Review, 
Flammability Reduction and Maintenance and Inspection Requirements'' 
(66 FR 23086, May 7, 2001). In addition to new airworthiness standards 
for transport airplanes and new maintenance requirements, this rule 
included Special Federal Aviation Regulation No. 88 (``SFAR 88,'' 
Amendment 21-78, and subsequent Amendments 21-82 and 21-83).
    Among other actions, SFAR 88 (66 FR 23086, May 7, 2001) requires 
certain type design (i.e., type certificate (TC) and supplemental type 
certificate (STC)) holders to substantiate that their fuel tank systems 
can prevent ignition sources in the fuel tanks. This requirement 
applies to type design holders for large turbine-powered transport 
airplanes and for subsequent modifications to those airplanes. It 
requires them to perform design reviews and to develop design changes 
and maintenance procedures if their designs do not meet the new fuel 
tank safety standards. As explained in the preamble to the rule, we 
intended to adopt airworthiness directives to mandate any changes found 
necessary to address unsafe conditions identified as a result of these 
reviews.
    In evaluating these design reviews, we have established four 
criteria intended to define the unsafe conditions associated with fuel 
tank systems that require corrective actions. The percentage of 
operating time during which fuel tanks are exposed to flammable 
conditions is one of these criteria. The other three criteria address 
the failure types under evaluation: Single failures, single failures in 
combination with a latent condition(s), and in-service failure 
experience. For all four criteria, the evaluations included 
consideration of previous actions taken that may mitigate the need for 
further action.
    The Joint Aviation Authorities (JAA) has issued a regulation that 
is similar to SFAR 88 (66 FR 23086, May 7, 2001). (The JAA is an 
associated body of the European Civil Aviation Conference (ECAC) 
representing the civil aviation regulatory authorities of a number of 
European States who have agreed to co-operate in developing and 
implementing common safety regulatory standards and procedures.) Under 
this regulation, the JAA stated that all members of the ECAC that hold 
type certificates for transport category airplanes are required to 
conduct a design review against explosion risks.
    We have determined that the actions identified in this AD are 
necessary to reduce the potential of ignition sources inside fuel 
tanks, which, in combination with flammable fuel vapors, could result 
in fuel tank explosions and consequent loss of the airplane.

Relevant Service Information

    Fokker Services B.V. has issued Fokker Service Bulletin SBF100-28-
073, dated August 10, 2012, including the following attachments (* the 
issue date is not specified on the drawing) and manual change 
notification:
     Fokker Drawing W41192, Sheet 052, Issue AS*;
     Fokker Drawing W41192, Sheet 054, Issue AR*;
     Fokker Drawing W59520, Sheet 003, Issue F, dated May 12, 
2011; and
     Fokker Manual Change Notification MCNM F100-150, dated 
August 10, 2012.

The actions described in this service information are intended to 
correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.
    This AD requires revisions to certain operator maintenance 
documents to include new Critical Design Configuration Control 
Limitations (CDCCLs). Compliance with these CDCCLs is required by 14 
CFR 91.403(c). For airplanes that have been previously modified, 
altered, or repaired in the areas addressed by this AD, the operator 
may not be able to accomplish the actions described in the revisions. 
In this situation, to comply with 14 CFR 91.403(c), the operator must 
request approval for an alternative method of compliance according to 
paragraph (j) of this AD. The request should include a description of 
changes to the required actions that will ensure the continued 
operational safety of the airplane.

Costs of Compliance

    We estimate that this proposed AD affects 10 products of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:

[[Page 46300]]



                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
               Action                        Labor cost           Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
Installation and revision of          7 work-hours x $85 per           $2,100           $2,695          $26,950
 maintenance program.                  hour = $595.
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

Fokker Services B.V.: Docket No. FAA-2013-0629; Directorate 
Identifier 2012-NM-214-AD.

(a) Comments Due Date

    We must receive comments by September 16, 2013.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Fokker Services B.V. Model F.28 Mark 0070 and 
0100 airplanes, certificated in any category, equipped with a center 
wing fuel tank.

(d) Subject

    Air Transport Association (ATA) of America Code 28, Fuel.

(e) Reason

    This AD was prompted by a design review, which revealed that 
under certain failure conditions of the maximum level (Max Level) 
sensor wiring, a short circuit may develop that causes a hot spot on 
the wiring conduit, or puncturing of the wiring conduit wall in the 
center wing fuel tank. We are issuing this AD to prevent an ignition 
source in the center wing fuel tank vapor space, which could result 
in a fuel tank explosion and consequent loss of the airplane.

(f) Compliance

    You are responsible for having the actions required by this AD 
performed within the compliance times specified, unless the actions 
have already been done.

(g) Installation of Fuses

    Within 24 months after the effective date of this AD: Do the 
actions specified in paragraphs (g)(1) and (g)(2) of this AD, as 
applicable.
    (1) For Fokker Services B.V. Model F.28 Mark 0070 airplanes 
having serial numbers 11244 through 11441 inclusive, equipped with a 
center wing bag tank: Install fuses in the wiring of the Max Level 
sensors of the center wing fuel tank, in accordance with Parts 1 and 
3 of the Accomplishment Instructions of Fokker Service Bulletin 
SBF100-28-073, dated August 10, 2012, which includes the attachments 
identified in paragraphs (g)(1)(i) through (g)(1)(iv) of this AD (* 
the issue date is not specified on the drawing).
    (i) Fokker Drawing W41192, Sheet 052, Issue AS*.
    (ii) Fokker Drawing W41192, Sheet 054, Issue AR*.
    (iii) Fokker Drawing W59520, Sheet 003, Issue F, dated May 12, 
2011.
    (iv) Fokker Manual Change Notification MCNM F100-150, dated 
August 10, 2012.
    (2) For Fokker Services B.V. Model F.28 Mark 0070 and Mark 0100 
airplanes having serial numbers 11442 and up, equipped with an 
integral center wing tank: Install fuses in the wiring of the Max 
Level sensors of the center wing fuel tank, in accordance with Parts 
2 and 3 of the Accomplishment Instructions of Fokker Service 
Bulletin SBF100-28-073, dated August 10, 2012, which includes the 
attachments identified in paragraphs (g)(2)(i) through (g)(2)(iv) of 
this AD (* the issue date is not specified on the drawing).
    (i) Fokker Drawing W41192, Sheet 052, Issue AS*.
    (ii) Fokker Drawing W41192, Sheet 054, Issue AR*.
    (iii) Fokker Drawing W59520, Sheet 003, Issue F, dated May 12, 
2011.
    (iv) Fokker Manual Change Notification MCNM F100-150, dated 
August 10, 2012.

(h) Revision of Maintenance or Inspection Program

    After doing any action required by paragraph (g) of this AD, 
before further flight, revise the airplane maintenance or inspection 
program, as applicable, by incorporating the CDCCLs specified in 
paragraph 1.L.(1)(c) of Fokker Service Bulletin SBF100-28-073, dated 
August 10, 2012, including the drawings specified in paragraphs 
(h)(1) through (h)(4) of this AD (* the issue date is not specified 
on the drawing) and manual change notification.
    (1) Fokker Drawing W41192, Sheet 052, Issue AS*.
    (2) Fokker Drawing W41192, Sheet 054, Issue AR*.
    (3) Fokker Drawing W59520, Sheet 003, Issue F, dated May 12, 
2011.
    (4) Fokker Manual Change Notification MCNM F100-150, dated 
August 10, 2012.

(i) No Alternative CDCCLs

    After the CDCCLs have been incorporated, as required by 
paragraph (h) of this AD, no alternative CDCCLs may be used unless 
the CDCCLs are approved as an alternative method of compliance 
(AMOC) in

[[Page 46301]]

accordance with the procedures specified in paragraph (j) of this 
AD.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to ATTN: Tom 
Rodriguez, Aerospace Engineer, International Branch; ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, 
WA 98057-3356; telephone 425-227-1137; fax 425-227-1137. Information 
may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office. The 
AMOC approval letter must specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

(k) Related Information

    (1) Refer to the Mandatory Continuing Airworthiness Information 
(MCAI) European Aviation Safety Agency Airworthiness Directive 2012-
0240, dated November 12, 2012, for related information. The MCAI can 
be found in the AD docket on the Internet at 
http:[sol][sol]regulations.gov.
    (2) For service information identified in this AD, contact 
Fokker Services B.V., Technical Services Dept., P.O. Box 1357, 2130 
EL Hoofddorp, the Netherlands; telephone +31 (0)88-6280-350; fax +31 
(0)88-6280-111; email technicalservices@fokker.com; Internet 
http:[sol][sol]www.myfokkerfleet.com. You may review copies of the 
referenced service information at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue SW., Renton, WA. For information on 
the availability of this material at the FAA, call 425 227-1221.

    Issued in Renton, Washington, on July 21, 2013.
Stephen P. Boyd,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2013-18390 Filed 7-30-13; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.