Airworthiness Directives; The Boeing Company Airplanes, 23110-23112 [2013-08907]

Download as PDF 23110 Federal Register / Vol. 78, No. 75 / Thursday, April 18, 2013 / Rules and Regulations DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2012–0932; Directorate Identifier 2012–NM–014–AD; Amendment 39–17426; AD 2013–08–09] Examining the AD Docket RIN 2120–AA64 Airworthiness Directives; The Boeing Company Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Final rule. AGENCY: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777–200, –200LR, –300, –300ER, and 777F series airplanes. This AD was prompted by a report that during a test of the oxygen system, an operator found that the passenger oxygen masks did not properly flow oxygen, and that a loud noise occurred in the overhead area, which was caused by the flex line separating from the hard line due to a missing clamshell coupler. This AD requires, for certain airplanes, performing a detailed inspection of certain areas of the airplane oxygen system to ensure clamshell couplers are installed and fully latched, and corrective actions if necessary. For all airplanes, this AD requires performing and meeting the requirements of the low pressure leak test. We are issuing this AD to prevent the oxygen system flex line from separating from the hard line, which could cause an oxygen leak and a drop in the oxygen system pressure, resulting in improper flow of oxygen through the passenger masks and injury to passengers if emergency oxygen is needed. SUMMARY: This AD is effective May 23, 2013. The Director of the Federal Register approved the incorporation by reference of a certain publication listed in the AD as of May 23, 2013. ADDRESSES: For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H–65, Seattle, Washington 98124– 2207; telephone 206–544–5000, extension 1; fax 206–766–5680; Internet https://www.myboeingfleet.com. You may review copies of the referenced TKELLEY on DSK3SPTVN1PROD with RULES DATES: VerDate Mar<15>2010 16:07 Apr 17, 2013 Jkt 229001 service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, Washington. For information on the availability of this material at the FAA, call 425–227– 1221. You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the regulatory evaluation, any comments received, and other information. The address for the Docket Office (phone: 800–647–5527) is Document Management Facility, U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Susan Monroe, Aerospace Engineer, Cabin Safety and Environmental Systems Branch, ANM–150S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW., Renton, WA 98057–3356; phone: 425–917–6457; fax: 425–917–6590; email: susan.l.monroe@faa.gov. SUPPLEMENTARY INFORMATION: Discussion We issued a Notice of Proposed Rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM published in the Federal Register on September 11, 2012 (77 FR 55768). That NPRM proposed to require, for certain airplanes, performing a detailed inspection of certain areas of the airplane oxygen system to ensure clamshell couplers are installed and fully latched, and corrective actions if necessary. For all airplanes, that NPRM proposed to require performing and meeting the requirements of the low pressure leak test. Comments We gave the public the opportunity to participate in developing this AD. The Boeing Company and Kristopher Charles Kleiner supported this final rule. The following presents the comment received on the NPRM (77 FR 55768, September 11, 2012) and the FAA’s response to the comment. PO 00000 Frm 00006 Fmt 4700 Sfmt 4700 Request Clarification of Note 1 to Paragraph (i) of NPRM (77 FR 55768, September 11, 2012) Air New Zealand requested clarification of Note 1 to paragraph (i) of the NPRM (77 FR 55768, September 11, 2012). Air New Zealand asked if the FAA intended to state a specific revision for the installation of the clamshell coupler in Subject 35–00–00, Oxygen, of Chapter 35, Oxygen, of Part II, Practices and Procedures, of the Boeing 777 Aircraft Maintenance Manual, Revision 65, dated May 5, 2012, knowing that it will be revised within the time frame of this NPRM. Air New Zealand also asked if an alternative method of compliance (AMOC) will be required if an operator intends to use a later revision of the maintenance manual. We agree to provide clarification of Note 1 to paragraph (i) of the NPRM (77 FR 55768, September 11, 2012). Note 1 to paragraph (i) of the NPRM is provided as guidance and is not an AD requirement; therefore, approval of an AMOC will not be required for using later revisions of the maintenance manual. Since we issued the NPRM, the aircraft maintenance manual has been revised. We have updated Note 1 to paragraph (i) of this AD with the latest revision. We have changed this AD accordingly. Conclusion We reviewed the relevant data, considered the comment received, and determined that air safety and the public interest require adopting the AD with the change described previously— and minor editorial changes. We have determined that these minor changes: • Are consistent with the intent that was proposed in the NPRM (77 FR 55768, September 11, 2012) for correcting the unsafe condition; and • Do not add any additional burden upon the public than was already proposed in the NPRM (77 FR 55768, September 11, 2012). We also determined that these changes will not increase the economic burden on any operator or increase the scope of the AD. Costs of Compliance We estimate that this AD affects 6 airplanes of U.S. registry. We estimate the following costs to comply with this AD: E:\FR\FM\18APR1.SGM 18APR1 Federal Register / Vol. 78, No. 75 / Thursday, April 18, 2013 / Rules and Regulations 23111 ESTIMATED COSTS Parts cost Action Labor cost Detailed inspection and leak test ............................ $0 $2,210 26 work-hours × $85 per hour = $2,210 ................ We have received no definitive data that would enable us to provide cost estimates for the on-condition actions specified in this AD. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings TKELLEY on DSK3SPTVN1PROD with RULES Cost per product This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Is not a ‘‘significant rule’’ under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), (3) Will not affect intrastate aviation in Alaska, and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ 2013–08–09 The Boeing Company: Amendment 39–17426; Docket No. FAA–2012–0932; Directorate Identifier 2012–NM–014–AD. (a) Effective Date This AD is effective May 23, 2013. (b) Affected ADs None. (c) Applicability This AD applies to The Boeing Company Model 777–200, –200LR, –300, –300ER, and 777F series airplanes; certificated in any category; as identified in Boeing Special Attention Service Bulletin 777–35–0024, dated September 1, 2011. (d) Subject Joint Aircraft System Component (JASC)/ Air Transport Association (ATA) of America Code 35, Oxygen. (e) Unsafe Condition This AD was prompted by a report that during a test of the oxygen system, an operator found that the passenger oxygen masks did not properly flow oxygen and that a loud noise occurred in the overhead area, which was caused by the flex line separating from the hard line due to a missing clamshell coupler. We are issuing this AD to prevent the oxygen system flex line from separating from the hard line, which could cause an oxygen leak and a drop in the oxygen system pressure, resulting in improper flow of oxygen through the passenger masks and injury to passengers if emergency oxygen is needed. List of Subjects in 14 CFR Part 39 (f) Compliance Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Comply with this AD within the compliance times specified, unless already done. VerDate Mar<15>2010 16:07 Apr 17, 2013 Jkt 229001 PO 00000 Frm 00007 Fmt 4700 Sfmt 4700 Cost on U.S. operators $13,260 (g) Inspection Within 36 months after the effective date of this AD, do the applicable actions in paragraph (g)(1) or (g)(2) of this AD. (1) For Groups 1–6, 8, and 9 airplanes, as identified in Boeing Special Attention Service Bulletin 777–35–0024, dated September 1, 2011: Do a detailed inspection of certain areas of the airplane oxygen system to ensure clamshell couplers are installed and fully latched, and perform and meet the requirements of the low pressure leak test, in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 777–35–0024, dated September 1, 2011. (2) For Group 7 airplanes, as identified in Boeing Special Attention Service Bulletin 777–35–0024, dated September 1, 2011: Perform and meet requirements of the low pressure leak test, in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 777–35– 0024, dated September 1, 2011. (h) Corrective Action if Clamshell Coupler Is Not Fully Latched If, during any inspection required by paragraph (g) of this AD, any clamshell coupler is not fully latched: Before further flight, latch the clamshell coupler, in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 777–35–0024, dated September 1, 2011. (i) Corrective Action if Clamshell Coupler Is Not Installed If, during any inspection required by paragraph (g) of this AD, any clamshell coupler is not installed: Before further flight, install a clamshell coupler. Note 1 to paragraph (i) of this AD: Guidance on installation of the clamshell coupler may be found in Subject 35–00–00, Oxygen, of Chapter 35, Oxygen, of Part II, Practices and Procedures, of the Boeing 777 Aircraft Maintenance Manual, Revision 67, dated January 5, 2013. (j) Alternative Methods of Compliance (AMOCs) (1) The Manager, Seattle Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in the Related Information section of this AD. Information may be emailed to: 9-ANMSeattle-ACO-AMOC-Requests@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, E:\FR\FM\18APR1.SGM 18APR1 23112 Federal Register / Vol. 78, No. 75 / Thursday, April 18, 2013 / Rules and Regulations or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. (k) Related Information For more information about this AD, contact Susan Monroe, Aerospace Engineer, Cabin Safety and Environmental Systems Branch, ANM–150S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW., Renton, WA 98057–3356; phone: 425–917– 6457; fax: 425–917–6590; email: susan.l.monroe@faa.gov. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Boeing Special Attention Service Bulletin 777–35–0024, dated September 1, 2011. (ii) Reserved. (3) For Boeing service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H–65, Seattle, Washington 98124–2207; telephone 206–544–5000, extension 1; fax 206–766–5680; Internet https:// www.myboeingfleet.com. (4) You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, Washington. For information on the availability of this material at the FAA, call 425–227–1221. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https:// www.archives.gov/federal-register/cfr/ibrlocations.html. Issued in Renton, Washington, on April 5, 2013. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2013–08907 Filed 4–17–13; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration ACTION: Final rule. We are adopting a new airworthiness directive (AD) for GrobWerke Model G115EG airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracks in the elevator trim tab arms on several Grob G 115 airplanes, which could result in failure of the part and consequent loss of control. We are issuing this AD to require actions to address the unsafe condition on these products. DATES: This AD is effective May 23, 2013. The Director of the Federal Register approved the incorporation by reference of a certain publication listed in the AD as of May 23, 2013. ADDRESSES: You may examine the AD docket on the Internet at https:// www.regulations.gov or in person at Document Management Facility, U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. For service information identified in this AD, contact Grob Aircraft AG, Lettenbachstrasse 9, D–86874 Tussenhausen-Mattsies, Germany; telephone: +49 (0) 8268 998 139; fax: +49 (0) 8268 998 200; email: productsupport@grob-aircraft.de; Internet: www.grob-aircraft.com/ index.php/g-115e.html. You may review copies of the referenced service information at the FAA, Small Airplane Directorate, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the FAA, call (816) 329–4148. FOR FURTHER INFORMATION CONTACT: Taylor Martin, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329– 4138; fax: (816) 329–4090; email: taylor.martin@faa.gov. SUMMARY: SUPPLEMENTARY INFORMATION: [Docket No. FAA–2013–0013; Directorate Identifier 2012–CE–046–AD; Amendment 39–17421; AD 2013–08–04] TKELLEY on DSK3SPTVN1PROD with RULES 14 CFR Part 39 Discussion RIN 2120–AA64 Airworthiness Directives; Grob-Werke Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). AGENCY: VerDate Mar<15>2010 16:07 Apr 17, 2013 Jkt 229001 We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM was published in the Federal Register on January 15, 2013 (78 FR 2910). That NPRM proposed to correct an unsafe condition for the specified products. The MCAI states: PO 00000 Frm 00008 Fmt 4700 Sfmt 4700 On several Grob G 115 aeroplanes, elevator trim tab arms Part Number (P/N) 115E–3758 have been found cracked, from a rear mounting hole (either L/H or R/H) to the rear edge of the trim tab arm. This condition, if not detected and corrected, could lead to further crack propagation, possibly resulting in failure of the part and consequent loss of control of the aeroplane. For the reasons described above, this AD requires repetitive inspections of the elevator trim tab arm to detect cracks and, if detected, replacement of the part with a serviceable part. This AD also provides an optional terminating action for the repetitive inspections. The Model G115EG airplane is the only airplane type-certificated in the United States with the same part numbers and similar configuration as the airplane model described in the MCAI. Comments We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM (78 FR 2910, January 15, 2013) or on the determination of the cost to the public. Conclusion We reviewed the relevant data and determined that air safety and the public interest require adopting the AD as proposed except for minor editorial changes. We have determined that these minor changes: • Are consistent with the intent that was proposed in the NPRM (78 FR 2910, January 15, 2013) for correcting the unsafe condition; and • Do not add any additional burden upon the public than was already proposed in the NPRM (78 FR 2910, January 15, 2013). Costs of Compliance We estimate that this AD will affect 0 products of U.S. registry. We also estimate that it would take about 3 work-hours per product to comply with the basic requirements of this AD. The average labor rate is $85 per work-hour. Required parts would cost about $372 per product. Based on these figures, we estimate the cost of this AD on U.S. operators to be $627 per product. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. E:\FR\FM\18APR1.SGM 18APR1

Agencies

[Federal Register Volume 78, Number 75 (Thursday, April 18, 2013)]
[Rules and Regulations]
[Pages 23110-23112]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2013-08907]



[[Page 23110]]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2012-0932; Directorate Identifier 2012-NM-014-AD; 
Amendment 39-17426; AD 2013-08-09]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
The Boeing Company Model 777-200, -200LR, -300, -300ER, and 777F series 
airplanes. This AD was prompted by a report that during a test of the 
oxygen system, an operator found that the passenger oxygen masks did 
not properly flow oxygen, and that a loud noise occurred in the 
overhead area, which was caused by the flex line separating from the 
hard line due to a missing clamshell coupler. This AD requires, for 
certain airplanes, performing a detailed inspection of certain areas of 
the airplane oxygen system to ensure clamshell couplers are installed 
and fully latched, and corrective actions if necessary. For all 
airplanes, this AD requires performing and meeting the requirements of 
the low pressure leak test. We are issuing this AD to prevent the 
oxygen system flex line from separating from the hard line, which could 
cause an oxygen leak and a drop in the oxygen system pressure, 
resulting in improper flow of oxygen through the passenger masks and 
injury to passengers if emergency oxygen is needed.

DATES: This AD is effective May 23, 2013.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in the AD as of May 23, 2013.

ADDRESSES: For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207; telephone 206-
544-5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may review copies of the referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, Washington. For information on the availability of 
this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, the regulatory evaluation, 
any comments received, and other information. The address for the 
Docket Office (phone: 800-647-5527) is Document Management Facility, 
U.S. Department of Transportation, Docket Operations, M-30, West 
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., 
Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Susan Monroe, Aerospace Engineer, 
Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, Seattle 
Aircraft Certification Office, 1601 Lind Avenue SW., Renton, WA 98057-
3356; phone: 425-917-6457; fax: 425-917-6590; email: 
susan.l.monroe@faa.gov.

SUPPLEMENTARY INFORMATION: 

Discussion

    We issued a Notice of Proposed Rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM published in the Federal Register on September 11, 2012 (77 
FR 55768). That NPRM proposed to require, for certain airplanes, 
performing a detailed inspection of certain areas of the airplane 
oxygen system to ensure clamshell couplers are installed and fully 
latched, and corrective actions if necessary. For all airplanes, that 
NPRM proposed to require performing and meeting the requirements of the 
low pressure leak test.

Comments

    We gave the public the opportunity to participate in developing 
this AD. The Boeing Company and Kristopher Charles Kleiner supported 
this final rule. The following presents the comment received on the 
NPRM (77 FR 55768, September 11, 2012) and the FAA's response to the 
comment.

Request Clarification of Note 1 to Paragraph (i) of NPRM (77 FR 55768, 
September 11, 2012)

    Air New Zealand requested clarification of Note 1 to paragraph (i) 
of the NPRM (77 FR 55768, September 11, 2012). Air New Zealand asked if 
the FAA intended to state a specific revision for the installation of 
the clamshell coupler in Subject 35-00-00, Oxygen, of Chapter 35, 
Oxygen, of Part II, Practices and Procedures, of the Boeing 777 
Aircraft Maintenance Manual, Revision 65, dated May 5, 2012, knowing 
that it will be revised within the time frame of this NPRM. Air New 
Zealand also asked if an alternative method of compliance (AMOC) will 
be required if an operator intends to use a later revision of the 
maintenance manual.
    We agree to provide clarification of Note 1 to paragraph (i) of the 
NPRM (77 FR 55768, September 11, 2012). Note 1 to paragraph (i) of the 
NPRM is provided as guidance and is not an AD requirement; therefore, 
approval of an AMOC will not be required for using later revisions of 
the maintenance manual. Since we issued the NPRM, the aircraft 
maintenance manual has been revised. We have updated Note 1 to 
paragraph (i) of this AD with the latest revision. We have changed this 
AD accordingly.

Conclusion

    We reviewed the relevant data, considered the comment received, and 
determined that air safety and the public interest require adopting the 
AD with the change described previously--and minor editorial changes. 
We have determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM (77 FR 55768, September 11, 2012) for correcting the unsafe 
condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM (77 FR 55768, September 11, 2012).
    We also determined that these changes will not increase the 
economic burden on any operator or increase the scope of the AD.

Costs of Compliance

    We estimate that this AD affects 6 airplanes of U.S. registry.
    We estimate the following costs to comply with this AD:

[[Page 23111]]



                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                              Parts     Cost per   Cost on U.S.
                   Action                              Labor cost              cost     product      operators
----------------------------------------------------------------------------------------------------------------
Detailed inspection and leak test..........  26 work-hours x $85 per hour          $0     $2,210         $13,260
                                              = $2,210.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2013-08-09 The Boeing Company: Amendment 39-17426; Docket No. FAA-
2012-0932; Directorate Identifier 2012-NM-014-AD.

(a) Effective Date

    This AD is effective May 23, 2013.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 777-200, -200LR, -
300, -300ER, and 777F series airplanes; certificated in any 
category; as identified in Boeing Special Attention Service Bulletin 
777-35-0024, dated September 1, 2011.

(d) Subject

    Joint Aircraft System Component (JASC)/Air Transport Association 
(ATA) of America Code 35, Oxygen.

(e) Unsafe Condition

    This AD was prompted by a report that during a test of the 
oxygen system, an operator found that the passenger oxygen masks did 
not properly flow oxygen and that a loud noise occurred in the 
overhead area, which was caused by the flex line separating from the 
hard line due to a missing clamshell coupler. We are issuing this AD 
to prevent the oxygen system flex line from separating from the hard 
line, which could cause an oxygen leak and a drop in the oxygen 
system pressure, resulting in improper flow of oxygen through the 
passenger masks and injury to passengers if emergency oxygen is 
needed.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection

    Within 36 months after the effective date of this AD, do the 
applicable actions in paragraph (g)(1) or (g)(2) of this AD.
    (1) For Groups 1-6, 8, and 9 airplanes, as identified in Boeing 
Special Attention Service Bulletin 777-35-0024, dated September 1, 
2011: Do a detailed inspection of certain areas of the airplane 
oxygen system to ensure clamshell couplers are installed and fully 
latched, and perform and meet the requirements of the low pressure 
leak test, in accordance with the Accomplishment Instructions of 
Boeing Special Attention Service Bulletin 777-35-0024, dated 
September 1, 2011.
    (2) For Group 7 airplanes, as identified in Boeing Special 
Attention Service Bulletin 777-35-0024, dated September 1, 2011: 
Perform and meet requirements of the low pressure leak test, in 
accordance with the Accomplishment Instructions of Boeing Special 
Attention Service Bulletin 777-35-0024, dated September 1, 2011.

(h) Corrective Action if Clamshell Coupler Is Not Fully Latched

    If, during any inspection required by paragraph (g) of this AD, 
any clamshell coupler is not fully latched: Before further flight, 
latch the clamshell coupler, in accordance with the Accomplishment 
Instructions of Boeing Special Attention Service Bulletin 777-35-
0024, dated September 1, 2011.

(i) Corrective Action if Clamshell Coupler Is Not Installed

    If, during any inspection required by paragraph (g) of this AD, 
any clamshell coupler is not installed: Before further flight, 
install a clamshell coupler.

    Note 1 to paragraph (i) of this AD:  Guidance on installation of 
the clamshell coupler may be found in Subject 35-00-00, Oxygen, of 
Chapter 35, Oxygen, of Part II, Practices and Procedures, of the 
Boeing 777 Aircraft Maintenance Manual, Revision 67, dated January 
5, 2013.

(j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle Certification Office (ACO), FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the manager of the ACO, send it to the attention of the 
person identified in the Related Information section of this AD. 
Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector,

[[Page 23112]]

or lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.

(k) Related Information

    For more information about this AD, contact Susan Monroe, 
Aerospace Engineer, Cabin Safety and Environmental Systems Branch, 
ANM-150S, FAA, Seattle Aircraft Certification Office, 1601 Lind 
Avenue SW., Renton, WA 98057-3356; phone: 425-917-6457; fax: 425-
917-6590; email: susan.l.monroe@faa.gov.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Boeing Special Attention Service Bulletin 777-35-0024, dated 
September 1, 2011.
    (ii) Reserved.
    (3) For Boeing service information identified in this AD, 
contact Boeing Commercial Airplanes, Attention: Data & Services 
Management, P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207; 
telephone 206-544-5000, extension 1; fax 206-766-5680; Internet 
https://www.myboeingfleet.com.
    (4) You may review copies of the referenced service information 
at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, Washington. For information on the availability of this 
material at the FAA, call 425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on April 5, 2013.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2013-08907 Filed 4-17-13; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.