Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Turbofan Engines, 17079-17080 [2013-06115]
Download as PDF
Federal Register / Vol. 78, No. 54 / Wednesday, March 20, 2013 / Rules and Regulations
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA–2012–1167; Directorate
Identifier 2012–NE–36–AD; Amendment 39–
17396; AD 2013–06–01]
RIN 2120–AA64
Airworthiness Directives; Rolls-Royce
Deutschland Ltd & Co KG Turbofan
Engines
Federal Aviation
Administration (FAA), DOT.
ACTION: Final rule.
AGENCY:
SUMMARY: We are adopting a new
airworthiness directive (AD) for certain
Rolls-Royce Deutschland Ltd & Co KG
(RRD) models Tay 620–15 and Tay 650–
15 turbofan engines. This AD was
prompted by RRD recalculating the
Declared Safe Cyclic Life (DSCL) for
certain low-pressure compressor (LPC)
rotor disc assemblies operating to the
Plan D Flight Mission. This AD requires
removing the affected LPC rotor disc
assemblies at a new lower recalculated
DSCL. We are issuing this AD to prevent
failure of the LPC rotor disc assembly,
uncontained engine failure, and damage
to the airplane.
DATES: This AD becomes effective April
24, 2013.
ADDRESSES: The Docket Operations
office is located at Docket Management
Facility, U.S. Department of
Transportation, 1200 New Jersey
Avenue SE., West Building Ground
Floor, Room W12–140, Washington, DC
20590–0001.
FOR FURTHER INFORMATION CONTACT:
Frederick Zink, Aerospace Engineer,
Engine Certification Office, FAA, Engine
& Propeller Directorate, 12 New England
Executive Park, Burlington, MA 01803;
phone: 781–238–7779; fax: 781–238–
7199; email: Frederick.zink@faa.gov.
SUPPLEMENTARY INFORMATION:
Comments
We gave the public the opportunity to
participate in developing this AD. We
received no comments on the NPRM
(77 FR 74123, December 13, 2012).
Conclusion
We reviewed the available data and
determined that air safety and the
public interest require adopting the AD
as proposed (77 FR 74123, December 13,
2012).
Costs of Compliance
We estimate that this AD will affect
four engines installed on airplanes of
U.S. registry. We also estimate that it
will require four hours to perform the
actions required by this AD. The average
labor rate is $85 per hour. Prorated life
for the disc assembly is approximately
$650 per disc. Based on these figures,
we estimate the cost of this AD on U.S.
operators to be $3,960.
We issued a notice of proposed
rulemaking (NPRM) to amend 14 CFR
part 39 to include an AD that would
apply to the specified products. That
NPRM was published in the Federal
Register on December 13, 2012 (77 FR
74123). That NPRM proposed to correct
an unsafe condition for the specified
products. The Mandatory Continuing
Airworthiness Information states:
Authority for This Rulemaking
Title 49 of the United States Code
specifies the FAA’s authority to issue
rules on aviation safety. Subtitle I,
section 106, describes the authority of
the FAA Administrator. ‘‘Subtitle VII:
Aviation Programs,’’ describes in more
detail the scope of the Agency’s
authority.
We are issuing this rulemaking under
the authority described in ‘‘Subtitle VII,
Part A, Subpart III, Section 44701:
General requirements.’’ Under that
section, Congress charges the FAA with
promoting safe flight of civil aircraft in
air commerce by prescribing regulations
for practices, methods, and procedures
the Administrator finds necessary for
safety in air commerce. This regulation
is within the scope of that authority
because it addresses an unsafe condition
that is likely to exist or develop on
products identified in this rulemaking
action.
The Tay 650–15 and Tay 650–15/10 engine
Time Limits Manual Chapter 05–10–01
contains maximum approved life limitations,
identified as Declared Safe Cyclic Life
(DSCL) for Low Pressure Compressor (LPC)
Regulatory Findings
We determined that this AD will not
have federalism implications under
Executive Order 13132. This AD will
Discussion
wreier-aviles on DSK5TPTVN1PROD with RULES
rotor disc assemblies Part Number (P/N)
JR31198A and P/N JR34563A operated to the
Plan D Flight Mission, which has been
recalculated to a lower value.
Decreased DSCL of LPC rotor disc
assemblies P/N JR31198A and P/N JR34563A
may affect these disc assemblies installed in
Tay 650–15 and Tay 650–15/10 engines as
well as in Tay 620–15 and Tay 620–15/20
engines.
Failure to take decreased DSCL of affected
LPC rotor disc assemblies into account could
lead to affected part failure and consequent
release of high energy debris potentially
resulting in damage to, and/or reduced
control of, the aeroplane.
VerDate Mar<14>2013
15:24 Mar 19, 2013
Jkt 229001
PO 00000
Frm 00009
Fmt 4700
Sfmt 4700
17079
not have a substantial direct effect on
the States, on the relationship between
the national government and the States,
or on the distribution of power and
responsibilities among the various
levels of government.
For the reasons discussed above, I
certify this AD:
1. Is not a ‘‘significant regulatory
action’’ under Executive Order 12866;
2. Is not a ‘‘significant rule’’ under the
DOT Regulatory Policies and Procedures
(44 FR 11034, February 26, 1979); and
3. Will not have a significant
economic impact, positive or negative,
on a substantial number of small entities
under the criteria of the Regulatory
Flexibility Act.
We prepared a regulatory evaluation
of the estimated costs to comply with
this AD and placed it in the AD docket.
Examining the AD Docket
You may examine the AD docket on
the Internet at https://
www.regulations.gov; or in person at the
Docket Operations office between 9 a.m.
and 5 p.m., Monday through Friday,
except Federal holidays. The AD docket
contains this AD, the regulatory
evaluation, any comments received, and
other information. The street address for
the Docket Operations office (phone:
800–647–5527) is provided in the
ADDRESSES section. Comments will be
available in the AD docket shortly after
receipt.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation
safety, Incorporation by reference,
Safety.
Adoption of the Amendment
Accordingly, under the authority
delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as
follows:
PART 39—AIRWORTHINESS
DIRECTIVES
1. The authority citation for part 39
continues to read as follows:
■
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13
[Amended]
2. The FAA amends § 39.13 by adding
the following new AD:
■
2013–06–01 Rolls-Royce Deutschland Ltd &
Co KG (RRD) (formerly Rolls-Royce plc):
Docket No. FAA–2012–1167; Directorate
Identifier 2012–NE–36–AD.
(a) Effective Date
This airworthiness directive (AD) becomes
effective April 24, 2013.
(b) Affected ADs
None.
E:\FR\FM\20MRR1.SGM
20MRR1
17080
Federal Register / Vol. 78, No. 54 / Wednesday, March 20, 2013 / Rules and Regulations
(c) Applicability
DEPARTMENT OF TRANSPORTATION
This AD applies to RRD models Tay 620–
15 and Tay 650–15 turbofan engines with a
low-pressure compressor (LPC) rotor disc
assembly, part number (P/N) JR31198A or
P/N JR34563A, installed.
(d) Reason
This AD was prompted by RRD
recalculating the Declared Safe Cyclic Life for
certain LPC rotor disc assemblies operating to
the Plan D Flight Mission. We are issuing this
AD to prevent failure of the LPC rotor disc
assembly, uncontained engine failure, and
damage to the airplane.
(e) Actions and Compliance
Unless already done, do the following. For
engines that have operated to the Plan D
Flight Mission configuration, remove the LPC
rotor disc assembly from service before
accumulating 18,700 engine flight cycles. Do
not return to service nor approve for return
to service any engine with the affected discs
installed that exceeds 18,700 engine flight
cycles.
(f) Alternative Methods of Compliance
(AMOCs)
The Manager, Engine Certification Office,
FAA, may approve AMOCs for this AD. Use
the procedures found in 14 CFR 39.19 to
make your request.
(g) Related Information
(1) For more information about this AD,
contact Frederick Zink, Aerospace Engineer,
Engine Certification Office, FAA, Engine &
Propeller Directorate, 12 New England
Executive Park, Burlington, MA 01803;
phone: 781–238–7779; fax: 781–238–7199;
email: Frederick.zink@faa.gov.
(2) Refer to European Aviation Safety
Agency AD 2012–0204, dated October 1,
2012, and RRD Alert Service Bulletin TAY–
72–A1772, dated August 9, 2012, for related
information.
(3) For service information identified in
this AD, contact Rolls-Royce Deutschland Ltd
& Co KG, Eschenweg 11 Dahlewitz 15827,
Blankenfelde-Mahlow, Germany; phone: +49
0 33–7086–1944; fax: +49 0 33–7086–3276.
(4) You may view this service information
at the FAA, Engine & Propeller Directorate,
12 New England Executive Park, Burlington,
MA. For information on the availability of
this material at the FAA, call 781–238–7125.
(h) Material Incorporated by Reference
wreier-aviles on DSK5TPTVN1PROD with RULES
None.
Issued in Burlington, Massachusetts, on
March 8, 2013.
Colleen M. D’Alessandro,
Acting Manager, Engine & Propeller
Directorate, Aircraft Certification Service.
[FR Doc. 2013–06115 Filed 3–19–13; 8:45 am]
BILLING CODE 4910–13–P
VerDate Mar<14>2013
15:24 Mar 19, 2013
Jkt 229001
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA–2012–1100; Directorate
Identifier 2012–NE–29–AD; Amendment 39–
17385; AD 2013–05–13]
RIN 2120–AA64
Airworthiness Directives; Rolls-Royce
Deutschland Ltd & Co KG Turbofan
Engines
Federal Aviation
Administration (FAA), DOT.
ACTION: Final rule.
AGENCY:
SUMMARY: We are adopting a new
airworthiness directive (AD) for certain
Rolls-Royce Deutschland Ltd & Co KG
(RRD) BR700–710 series turbofan
engines. This AD requires replacement
of the affected fuel pump splined
couplings. This AD was prompted by
service experience that demonstrated
premature wear of the splined coupling
on the fuel pump. We are issuing this
AD to prevent failure of the engine and
loss of the airplane.
DATES: This AD becomes effective April
24, 2013.
ADDRESSES: The Docket Operations
office is located at Docket Management
Facility, U.S. Department of
Transportation, 1200 New Jersey
Avenue SE., West Building Ground
Floor, Room W12–140, Washington, DC
20590–0001.
FOR FURTHER INFORMATION CONTACT:
Frederick Zink, Aerospace Engineer,
Engine Certification Office, FAA, Engine
& Propeller Directorate, 12 New England
Executive Park, Burlington, MA 01803;
email: frederick.zink@faa.gov; phone:
781–238–7779; fax: 781–238–7199.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed
rulemaking (NPRM) to amend 14 CFR
part 39 to include an AD that would
apply to the specified products. That
NPRM was published in the Federal
Register on November 7, 2012 (77 FR
66771). That NPRM proposed to require
replacement of the affected fuel pump
splined couplings. The Mandatory
Continuing Airworthiness Information
states:
In-service experience of RRD BR700–710
fuel pump installed on the rear face of the
accessory gearbox identified premature wear
of the splined coupling, which caused
damage to the splined coupling.
This condition, if not corrected, could lead
to failure of engine fuel supply, likely
resulting in an uncommanded in-flight
PO 00000
Frm 00010
Fmt 4700
Sfmt 4700
shutdown and consequently reduced control
of the aeroplane.
Comments
We gave the public the opportunity to
participate in developing this AD. We
considered the comment received.
Request To Withdraw the AD
An anonymous commenter requested
that the FAA withdraw the proposed
rule (77 FR 66771, November 7, 2012).
The commenter indicated that the rule
is a ‘‘waste of government resources’’
because a service bulletin has been
issued and larger companies and
individuals will comply because it is in
their best interest while smaller
companies will ‘‘suffer.’’
We do not agree. We reviewed the
service experience of the affected fuel
pump splined couplings and
determined that an unsafe condition
exists and that corrective action is
required. Although some operators may
take corrective action based on the
service bulletin, the issuance of an AD
makes compliance mandatory for all.
We made no change to the AD.
Change to Installation Prohibition
Paragraph
We determined when reviewing the
proposed rule (77 FR 66771, November
7, 2012), that the Installation
Prohibition paragraph (g) was not
consistent with the compliance
paragraph (e). The Installation
Prohibition paragraph in the NPRM
forbids returning to service any engine
with a fuel pump with an affected
splined coupling that has accumulated
4,000 hours time in service (TIS). This
prohibition is not consistent with
compliance paragraph (e) which allows
engines with affected spline couplings
to be returned to service for those
engines with 3,750 hours or more TIS,
while allowing an additional 250 hours
TIS to comply. The Installation
Prohibition paragraph should have been
directed against ‘‘installing’’ an affected
fuel pump into an engine or installing
an engine with an affected fuel pump
into an aircraft rather than against
returning an engine to service with an
affected fuel pump.
The Installation Prohibition paragraph
now reads: ‘‘After the effective date of
this AD, do not install into any engine
a fuel pump with an affected splined
coupling that has accumulated 4,000
hours TIS, or install any engine with an
affected splined coupling that has
accumulated 4,000 hours TIS onto an
airplane.’’
E:\FR\FM\20MRR1.SGM
20MRR1
Agencies
[Federal Register Volume 78, Number 54 (Wednesday, March 20, 2013)]
[Rules and Regulations]
[Pages 17079-17080]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2013-06115]
[[Page 17079]]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2012-1167; Directorate Identifier 2012-NE-36-AD;
Amendment 39-17396; AD 2013-06-01]
RIN 2120-AA64
Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG
Turbofan Engines
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for certain
Rolls-Royce Deutschland Ltd & Co KG (RRD) models Tay 620-15 and Tay
650-15 turbofan engines. This AD was prompted by RRD recalculating the
Declared Safe Cyclic Life (DSCL) for certain low-pressure compressor
(LPC) rotor disc assemblies operating to the Plan D Flight Mission.
This AD requires removing the affected LPC rotor disc assemblies at a
new lower recalculated DSCL. We are issuing this AD to prevent failure
of the LPC rotor disc assembly, uncontained engine failure, and damage
to the airplane.
DATES: This AD becomes effective April 24, 2013.
ADDRESSES: The Docket Operations office is located at Docket Management
Facility, U.S. Department of Transportation, 1200 New Jersey Avenue
SE., West Building Ground Floor, Room W12-140, Washington, DC 20590-
0001.
FOR FURTHER INFORMATION CONTACT: Frederick Zink, Aerospace Engineer,
Engine Certification Office, FAA, Engine & Propeller Directorate, 12
New England Executive Park, Burlington, MA 01803; phone: 781-238-7779;
fax: 781-238-7199; email: Frederick.zink@faa.gov.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
part 39 to include an AD that would apply to the specified products.
That NPRM was published in the Federal Register on December 13, 2012
(77 FR 74123). That NPRM proposed to correct an unsafe condition for
the specified products. The Mandatory Continuing Airworthiness
Information states:
The Tay 650-15 and Tay 650-15/10 engine Time Limits Manual
Chapter 05-10-01 contains maximum approved life limitations,
identified as Declared Safe Cyclic Life (DSCL) for Low Pressure
Compressor (LPC) rotor disc assemblies Part Number (P/N) JR31198A
and P/N JR34563A operated to the Plan D Flight Mission, which has
been recalculated to a lower value.
Decreased DSCL of LPC rotor disc assemblies P/N JR31198A and P/N
JR34563A may affect these disc assemblies installed in Tay 650-15
and Tay 650-15/10 engines as well as in Tay 620-15 and Tay 620-15/20
engines.
Failure to take decreased DSCL of affected LPC rotor disc
assemblies into account could lead to affected part failure and
consequent release of high energy debris potentially resulting in
damage to, and/or reduced control of, the aeroplane.
Comments
We gave the public the opportunity to participate in developing
this AD. We received no comments on the NPRM (77 FR 74123, December 13,
2012).
Conclusion
We reviewed the available data and determined that air safety and
the public interest require adopting the AD as proposed (77 FR 74123,
December 13, 2012).
Costs of Compliance
We estimate that this AD will affect four engines installed on
airplanes of U.S. registry. We also estimate that it will require four
hours to perform the actions required by this AD. The average labor
rate is $85 per hour. Prorated life for the disc assembly is
approximately $650 per disc. Based on these figures, we estimate the
cost of this AD on U.S. operators to be $3,960.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify this AD:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket.
Examining the AD Docket
You may examine the AD docket on the Internet at https://www.regulations.gov; or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The street address for
the Docket Operations office (phone: 800-647-5527) is provided in the
ADDRESSES section. Comments will be available in the AD docket shortly
after receipt.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new AD:
2013-06-01 Rolls-Royce Deutschland Ltd & Co KG (RRD) (formerly
Rolls-Royce plc): Docket No. FAA-2012-1167; Directorate Identifier
2012-NE-36-AD.
(a) Effective Date
This airworthiness directive (AD) becomes effective April 24,
2013.
(b) Affected ADs
None.
[[Page 17080]]
(c) Applicability
This AD applies to RRD models Tay 620-15 and Tay 650-15 turbofan
engines with a low-pressure compressor (LPC) rotor disc assembly,
part number (P/N) JR31198A or P/N JR34563A, installed.
(d) Reason
This AD was prompted by RRD recalculating the Declared Safe
Cyclic Life for certain LPC rotor disc assemblies operating to the
Plan D Flight Mission. We are issuing this AD to prevent failure of
the LPC rotor disc assembly, uncontained engine failure, and damage
to the airplane.
(e) Actions and Compliance
Unless already done, do the following. For engines that have
operated to the Plan D Flight Mission configuration, remove the LPC
rotor disc assembly from service before accumulating 18,700 engine
flight cycles. Do not return to service nor approve for return to
service any engine with the affected discs installed that exceeds
18,700 engine flight cycles.
(f) Alternative Methods of Compliance (AMOCs)
The Manager, Engine Certification Office, FAA, may approve AMOCs
for this AD. Use the procedures found in 14 CFR 39.19 to make your
request.
(g) Related Information
(1) For more information about this AD, contact Frederick Zink,
Aerospace Engineer, Engine Certification Office, FAA, Engine &
Propeller Directorate, 12 New England Executive Park, Burlington, MA
01803; phone: 781-238-7779; fax: 781-238-7199; email:
Frederick.zink@faa.gov.
(2) Refer to European Aviation Safety Agency AD 2012-0204, dated
October 1, 2012, and RRD Alert Service Bulletin TAY-72-A1772, dated
August 9, 2012, for related information.
(3) For service information identified in this AD, contact
Rolls-Royce Deutschland Ltd & Co KG, Eschenweg 11 Dahlewitz 15827,
Blankenfelde-Mahlow, Germany; phone: +49 0 33-7086-1944; fax: +49 0
33-7086-3276.
(4) You may view this service information at the FAA, Engine &
Propeller Directorate, 12 New England Executive Park, Burlington,
MA. For information on the availability of this material at the FAA,
call 781-238-7125.
(h) Material Incorporated by Reference
None.
Issued in Burlington, Massachusetts, on March 8, 2013.
Colleen M. D'Alessandro,
Acting Manager, Engine & Propeller Directorate, Aircraft Certification
Service.
[FR Doc. 2013-06115 Filed 3-19-13; 8:45 am]
BILLING CODE 4910-13-P