Airworthiness Directives; Cessna Aircraft Company Airplanes, 14640-14642 [2013-04901]

Download as PDF 14640 Federal Register / Vol. 78, No. 45 / Thursday, March 7, 2013 / Rules and Regulations List of Subjects in 9 CFR Part 424 Food additives, Food packaging, Meat inspection, Poultry and poultry products. For the reasons set forth in the preamble, FSIS is amending 9 CFR part 424 as follows: PART 424—PREPARATION AND PROCESSING OPERATIONS 1. The authority citation for part 424 continues to read as follows: ■ Authority: 7 U.S.C. 450, 1901–1906; 21 U.S.C. 451–470, 601–695; 7 CFR 2.18, 2.53. 2. In § 424.23, revise paragraph (a)(3) to read as follows: ■ § 424.23 Prohibited uses. (a) * * * (3) Sorbic acid, calcium sorbate, sodium sorbate, and other salts of sorbic acid shall not be used in cooked sausages or any other meat; sulfurous acid and salts of sulfurous acid shall not be used in or on any meat; and niacin or nicotinamide shall not be used in or on fresh meat product; except that potassium sorbate, propylparaben (propyl p-hydroxybenzoate), and calcium propionate, may be used in or on any product, only as provided in 9 CFR Chapter III. * * * * * Done at Washington, DC on: February 28, 2013. Alfred V. Almanza, Administrator. [FR Doc. 2013–05341 Filed 3–6–13; 8:45 am] BILLING CODE 3410–DM–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2012–0720; Directorate Identifier 2012–NM–059–AD; Amendment 39–17360; AD 2013–04–03] RIN 2120–AA64 Airworthiness Directives; Cessna Aircraft Company Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Final rule. emcdonald on DSK67QTVN1PROD with RULES AGENCY: SUMMARY: We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company Model 750 airplanes. This AD was prompted by reports of loss of displayed airspeed. This AD requires inspecting certain logic modules to determine if certain cabin altitude/pitot static heater module VerDate Mar<15>2010 14:39 Mar 06, 2013 Jkt 229001 assemblies are installed and replacing those assemblies with a new assembly; and revising the Non-Normal Procedures Section of the airplane flight manual (AFM) to include procedures for resetting the pitot switch in the event of pitot heater failure and for total loss of airspeed indication. We are issuing this AD to prevent the loss of all displayed airspeed, which could result in reduced ability to control the airplane. DATES: This AD is effective April 11, 2013. The Director of the Federal Register approved the incorporation by reference of certain publication listed in the AD as of April 11, 2013. ADDRESSES: For service information identified in this AD, contact Cessna Aircraft Co., P.O. Box 7706, Wichita, Kansas 67277; telephone 316–517–6215; fax 316–517–5802; email citationpubs@cessna.textron.com; Internet https:// www.cessnasupport.com/newlogin.html. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227– 1221. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the regulatory evaluation, any comments received, and other information. The address for the Docket Office (phone: 800–647–5527) is Document Management Facility, U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Christine Abraham, Aerospace Engineer, Electrical Systems and Avionics Branch, ACE–119W, FAA, Wichita Aircraft Certification Office (ACO), 1801 Airport Road, Room 100, Mid-Continent Airport, Wichita, Kansas 67209; phone: 316–946–4165; fax: 316–946–4107; email: Christine.Abraham@faa.gov. SUPPLEMENTARY INFORMATION: Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM published in the Federal Register on July 17, 2012 (77 FR 41937). PO 00000 Frm 00006 Fmt 4700 Sfmt 4700 That NPRM proposed to require inspecting certain logic modules to determine if certain cabin altitude/pitot static heater module assemblies are installed and replacing those assemblies with a new assembly; and revising the Non-Normal Procedures Section of the AFM to include procedures for resetting the pitot switch in the event of pitot heater failure and for total loss of airspeed indication. Comments We gave the public the opportunity to participate in developing this AD. The following presents the comments received on the proposal (77 FR 41937, July 17, 2012) and the FAA’s response to each comment. Request To Change Compliance Time Cessna Aircraft Company (Cessna) requested that the NPRM (77 FR 41937, July 17, 2012) use the compliance time described in Cessna Service Letter SL750–30–08, Revision 1, dated July 11, 2011, of within two years or 1,200 flight hours after July 11, 2011 (The issue date of Cessna Service Letter SL750–30–08, Revision 1), whichever occurs first. Cessna noted that the proposed NPRM compliance time is within 600 flight hours or one year after the effective date of the AD, whichever occurs first. Cessna stated that the NPRM compliance time will extend the compliance time beyond what is suggested by Cessna Service Letter SL750–30–08, Revision 1, dated July 11, 2011. We disagree with the request to change the compliance time. We coordinated with Cessna regarding the compliance time difference prior to issuing the NPRM (77 FR 41937, July 17, 2012). We have determined that a compliance time of within 600 flight hours or one year after the effective date of the AD (whichever occurs first) is an appropriate compliance time to adequately address the identified unsafe condition. If additional data are presented to justify a shorter compliance time, we might consider further rulemaking. We have not changed the AD in this regard. Request To Change Logic Module Designators Cessna requested that we change the reference designators to the logic modules in paragraph (g) of the NPRM (77 FR 41937, July 17, 2012). Cessna stated that NC006 and NC007 are the correct reference designators for the logic modules. We agree to change the references because we have determined that the commenter’s stated references are E:\FR\FM\07MRR1.SGM 07MRR1 Federal Register / Vol. 78, No. 45 / Thursday, March 7, 2013 / Rules and Regulations correct. We have changed paragraph (g) of this AD to refer to the logic modules as NC006 and NC007. Conclusion We reviewed the relevant data, considered the comments received, and determined that air safety and the public interest require adopting the AD with the change described previously and minor editorial changes. We have determined that these minor changes: • Are consistent with the intent that was proposed in the NPRM (77 FR 41937, July 17, 2012) for correcting the unsafe condition; and • Do not add any additional burden upon the public than was already proposed in the NPRM (77 FR 41937, July 17, 2012). 14641 We also determined that these changes will not increase the economic burden on any operator or increase the scope of the AD. Costs of Compliance We estimate that this AD affects 210 airplanes of U.S. registry. We estimate the following costs to comply with this AD: ESTIMATED COSTS Action Labor cost Inspection ................................ Revision .................................. 2 work-hours × $85 per hour = $170 ..................................... 1 work-hour × $85 per hour = $85 ......................................... We estimate the following costs to do any necessary replacements that would Cost per product Parts cost be required based on the results of the inspection. We have no way of $0 0 Cost on U.S. operators $170 85 $35,700 17,850 determining the number of aircraft that might need these replacements: ON-CONDITION COSTS Action Labor cost Replacement .................................... 1 work-hour × $85 per hour = $85 ............................................................ emcdonald on DSK67QTVN1PROD with RULES According to the manufacturer, some of the costs of this AD may be covered under warranty, thereby reducing the cost impact on affected individuals. We do not control warranty coverage for affected individuals. As a result, we have included all costs in our cost estimate. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on VerDate Mar<15>2010 16:40 Mar 06, 2013 Jkt 229001 Parts cost the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Is not a ‘‘significant rule’’ under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), (3) Will not affect intrastate aviation in Alaska, and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. PO 00000 Frm 00007 Fmt 4700 Sfmt 4700 § 39.13 Cost per product $4,058 $4,143 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ 2013–04–03 Cessna Aircraft Company: Amendment 39–17360; Docket No. FAA–2012–0720; Directorate Identifier 2012–NM–059–AD. (a) Effective Date This AD is effective April 11, 2013. (b) Affected ADs None. (c) Applicability This AD applies to The Cessna Aircraft Company Model 750 airplanes, certificated in any category, serial numbers 0001 through 0245 inclusive. (d) Subject Joint Aircraft System Component (JASC)/ Air Transport Association (ATA) of America Code 3030, Pitot/Static Anti-Ice System. (e) Unsafe Condition This AD was prompted by reports of loss of displayed airspeed. We are issuing this AD to prevent the loss of all displayed airspeed, which could result in reduced ability to control the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Inspection and Replacement Within 600 flight hours or one year after the effective date of this AD, whichever occurs first: Do an inspection of logic E:\FR\FM\07MRR1.SGM 07MRR1 14642 Federal Register / Vol. 78, No. 45 / Thursday, March 7, 2013 / Rules and Regulations modules NC006 and NC007 to determine if any cabin altitude/pitot static heater module assemblies having part number (P/N) 6718477–9, P/N 6718477–10, or P/N 9914731–1 are installed, in accordance with the Accomplishment Instructions of Cessna Service Letter SL750–30–08, Revision 1, dated July 11, 2011. If any altitude/pitot static heater module assembly having P/N 6718477–9, P/N 6718477–10, or P/N 9914731–1 is installed: Before further flight, replace that assembly with a new assembly having P/N 6718477–11, in accordance with the Accomplishment Instructions of Cessna Service Letter SL750–30–08, Revision 1, dated July 11, 2011. (h) Airplane Flight Manual (AFM) Revision Concurrently with the actions required by paragraph (g) of this AD: Revise the NonNormal Procedures Section of the Cessna 750 AFM to include the information in the flight manual changes identified in paragraphs (h)(1), (h)(2), (h)(3), (h)(4), (h)(5), and (h)(6) of this AD. This may be done by inserting copies of these flight manual changes into the Cessna 750 AFM. When these flight manual changes have been included in general revisions of the AFM, the general revisions may be inserted in the AFM, provided the relevant information in the general revision is identical to that in these flight manual changes, and then these temporary flight manual changes may be removed. (1) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FM TC– R11–23, approved June 26, 2012. (2) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FM TC– R11–24, approved June 26, 2012. (3) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FM TC– R11–25, approved June 26, 2012. (4) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FM TC– R11–26, approved June 26, 2012. (5) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FMA TC– R02–03, approved April 10, 2012. (6) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FMA TC– R02–07, approved June 26, 2012. emcdonald on DSK67QTVN1PROD with RULES (i) Parts Installation Prohibition As of the effective date of this AD, no person may install an altitude/pitot static heater module assembly having P/N 6718477–9, P/N 6718477–10, or P/N 9914731–1, on any airplane. (j) Special Flight Permit Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the airplane can be modified (if the operator elects to do so), provided the actions required by paragraph (h) of this AD have been accomplished. (k) Alternative Methods of Compliance (AMOCs) (1) The Manager, Wichita Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, VerDate Mar<15>2010 14:39 Mar 06, 2013 Jkt 229001 send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in the Related Information section of this AD. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. (l) Related Information For more information about this AD, contact Christine Abraham, Aerospace Engineer, Electrical Systems and Avionics Branch, ACE–119W, FAA, Wichita Aircraft Certification Office (ACO), 1801 Airport Road, Room 100, Mid-Continent Airport, Wichita, Kansas 67209; phone: 316–946– 4165; fax: 316–946–4107; email: Christine.Abraham@faa.gov. (m) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. (i) Cessna Service Letter SL750–30–08, Revision 1, dated July 11, 2011. (ii) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FM TC– R11–23, approved June 26, 2012. (iii) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FM TC– R11–24, approved June 26, 2012. (iv) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FM TC– R11–25, approved June 26, 2012. (v) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FM TC– R11–26, approved June 26, 2012. (vi) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FMA TC– R02–03, approved April 10, 2012. (vii) Cessna Temporary FAA Approved Airplane Flight Manual Change 75FMA TC– R02–07, approved June 26, 2012. (3) For Cessna service information identified in this AD, contact Cessna Aircraft Co., P.O. Box 7706, Wichita, Kansas 67277; telephone 316–517–6215; fax 316–517–5802; email citationpubs@cessna.textron.com; Internet https://www.cessnasupport.com/ newlogin.html. (4) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425–227–1221. (5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https:// www.archives.gov/federal-register/cfr/ibrlocations.html. PO 00000 Frm 00008 Fmt 4700 Sfmt 4700 Issued in Renton, Washington, on February 8, 2013. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2013–04901 Filed 3–6–13; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2012–1157; Directorate Identifier 2012–NM–061–AD; Amendment 39–17371; AD 2013–04–13] RIN 2120–AA64 Airworthiness Directives; BAE SYSTEMS (OPERATIONS) LIMITED Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. AGENCY: SUMMARY: We are adopting a new airworthiness directive (AD) for all BAE SYSTEMS (OPERATIONS) LIMITED Model BAe 146 and Avro 146–RJ series airplanes. This AD was prompted by a report that certain ceramic terminal blocks, through which the wiring for the engine fire extinguishers, fire detection circuits, and engine and intake anti-ice system are routed, have been found to have moisture ingress, which can degrade the insulation resistance of the ceramic terminal blocks. This AD requires a one-time insulation resistance test of ceramic terminal blocks, and if necessary, replacement of the blocks. We are issuing this AD to prevent latent failure of the number 2 fire bottle, which, in the event of an engine fire, could result in failure of the fire bottle to discharge when activated and possibly preventing the flightcrew from extinguishing an engine fire. DATES: This AD becomes effective April 11, 2013. The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of April 11, 2013. ADDRESSES: You may examine the AD docket on the Internet at https:// www.regulations.gov or in person at the U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC. FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer, E:\FR\FM\07MRR1.SGM 07MRR1

Agencies

[Federal Register Volume 78, Number 45 (Thursday, March 7, 2013)]
[Rules and Regulations]
[Pages 14640-14642]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2013-04901]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2012-0720; Directorate Identifier 2012-NM-059-AD; 
Amendment 39-17360; AD 2013-04-03]
RIN 2120-AA64


Airworthiness Directives; Cessna Aircraft Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Cessna Aircraft Company Model 750 airplanes. This AD was prompted by 
reports of loss of displayed airspeed. This AD requires inspecting 
certain logic modules to determine if certain cabin altitude/pitot 
static heater module assemblies are installed and replacing those 
assemblies with a new assembly; and revising the Non-Normal Procedures 
Section of the airplane flight manual (AFM) to include procedures for 
resetting the pitot switch in the event of pitot heater failure and for 
total loss of airspeed indication. We are issuing this AD to prevent 
the loss of all displayed airspeed, which could result in reduced 
ability to control the airplane.

DATES: This AD is effective April 11, 2013.
    The Director of the Federal Register approved the incorporation by 
reference of certain publication listed in the AD as of April 11, 2013.

ADDRESSES: For service information identified in this AD, contact 
Cessna Aircraft Co., P.O. Box 7706, Wichita, Kansas 67277; telephone 
316-517-6215; fax 316-517-5802; email citationpubs@cessna.textron.com; 
Internet https://www.cessnasupport.com/newlogin.html. You may review 
copies of the referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, the regulatory evaluation, 
any comments received, and other information. The address for the 
Docket Office (phone: 800-647-5527) is Document Management Facility, 
U.S. Department of Transportation, Docket Operations, M-30, West 
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., 
Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Christine Abraham, Aerospace Engineer, 
Electrical Systems and Avionics Branch, ACE-119W, FAA, Wichita Aircraft 
Certification Office (ACO), 1801 Airport Road, Room 100, Mid-Continent 
Airport, Wichita, Kansas 67209; phone: 316-946-4165; fax: 316-946-4107; 
email: Christine.Abraham@faa.gov.

SUPPLEMENTARY INFORMATION: 

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM published in the Federal Register on July 17, 2012 (77 FR 
41937). That NPRM proposed to require inspecting certain logic modules 
to determine if certain cabin altitude/pitot static heater module 
assemblies are installed and replacing those assemblies with a new 
assembly; and revising the Non-Normal Procedures Section of the AFM to 
include procedures for resetting the pitot switch in the event of pitot 
heater failure and for total loss of airspeed indication.

Comments

    We gave the public the opportunity to participate in developing 
this AD. The following presents the comments received on the proposal 
(77 FR 41937, July 17, 2012) and the FAA's response to each comment.

Request To Change Compliance Time

    Cessna Aircraft Company (Cessna) requested that the NPRM (77 FR 
41937, July 17, 2012) use the compliance time described in Cessna 
Service Letter SL750-30-08, Revision 1, dated July 11, 2011, of within 
two years or 1,200 flight hours after July 11, 2011 (The issue date of 
Cessna Service Letter SL750-30-08, Revision 1), whichever occurs first. 
Cessna noted that the proposed NPRM compliance time is within 600 
flight hours or one year after the effective date of the AD, whichever 
occurs first. Cessna stated that the NPRM compliance time will extend 
the compliance time beyond what is suggested by Cessna Service Letter 
SL750-30-08, Revision 1, dated July 11, 2011.
    We disagree with the request to change the compliance time. We 
coordinated with Cessna regarding the compliance time difference prior 
to issuing the NPRM (77 FR 41937, July 17, 2012). We have determined 
that a compliance time of within 600 flight hours or one year after the 
effective date of the AD (whichever occurs first) is an appropriate 
compliance time to adequately address the identified unsafe condition. 
If additional data are presented to justify a shorter compliance time, 
we might consider further rulemaking. We have not changed the AD in 
this regard.

Request To Change Logic Module Designators

    Cessna requested that we change the reference designators to the 
logic modules in paragraph (g) of the NPRM (77 FR 41937, July 17, 
2012). Cessna stated that NC006 and NC007 are the correct reference 
designators for the logic modules.
    We agree to change the references because we have determined that 
the commenter's stated references are

[[Page 14641]]

correct. We have changed paragraph (g) of this AD to refer to the logic 
modules as NC006 and NC007.

Conclusion

    We reviewed the relevant data, considered the comments received, 
and determined that air safety and the public interest require adopting 
the AD with the change described previously and minor editorial 
changes. We have determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM (77 FR 41937, July 17, 2012) for correcting the unsafe condition; 
and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM (77 FR 41937, July 17, 2012).
    We also determined that these changes will not increase the 
economic burden on any operator or increase the scope of the AD.

Costs of Compliance

    We estimate that this AD affects 210 airplanes of U.S. registry.
    We estimate the following costs to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
               Action                         Labor cost            Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Inspection.........................  2 work-hours x $85 per hour              $0            $170         $35,700
                                      = $170.
Revision...........................  1 work-hour x $85 per hour                0              85          17,850
                                      = $85.
----------------------------------------------------------------------------------------------------------------

    We estimate the following costs to do any necessary replacements 
that would be required based on the results of the inspection. We have 
no way of determining the number of aircraft that might need these 
replacements:

                                               On-Condition Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                   Action                                 Labor cost                Parts cost        product
----------------------------------------------------------------------------------------------------------------
Replacement................................  1 work-hour x $85 per hour = $85...          $4,058          $4,143
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some of the costs of this AD may be 
covered under warranty, thereby reducing the cost impact on affected 
individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2013-04-03 Cessna Aircraft Company: Amendment 39-17360; Docket No. 
FAA-2012-0720; Directorate Identifier 2012-NM-059-AD.

(a) Effective Date

    This AD is effective April 11, 2013.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Cessna Aircraft Company Model 750 
airplanes, certificated in any category, serial numbers 0001 through 
0245 inclusive.

(d) Subject

    Joint Aircraft System Component (JASC)/Air Transport Association 
(ATA) of America Code 3030, Pitot/Static Anti-Ice System.

(e) Unsafe Condition

    This AD was prompted by reports of loss of displayed airspeed. 
We are issuing this AD to prevent the loss of all displayed 
airspeed, which could result in reduced ability to control the 
airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection and Replacement

    Within 600 flight hours or one year after the effective date of 
this AD, whichever occurs first: Do an inspection of logic

[[Page 14642]]

modules NC006 and NC007 to determine if any cabin altitude/pitot 
static heater module assemblies having part number (P/N) 6718477-9, 
P/N 6718477-10, or P/N 9914731-1 are installed, in accordance with 
the Accomplishment Instructions of Cessna Service Letter SL750-30-
08, Revision 1, dated July 11, 2011. If any altitude/pitot static 
heater module assembly having P/N 6718477-9, P/N 6718477-10, or P/N 
9914731-1 is installed: Before further flight, replace that assembly 
with a new assembly having P/N 6718477-11, in accordance with the 
Accomplishment Instructions of Cessna Service Letter SL750-30-08, 
Revision 1, dated July 11, 2011.

(h) Airplane Flight Manual (AFM) Revision

    Concurrently with the actions required by paragraph (g) of this 
AD: Revise the Non-Normal Procedures Section of the Cessna 750 AFM 
to include the information in the flight manual changes identified 
in paragraphs (h)(1), (h)(2), (h)(3), (h)(4), (h)(5), and (h)(6) of 
this AD. This may be done by inserting copies of these flight manual 
changes into the Cessna 750 AFM. When these flight manual changes 
have been included in general revisions of the AFM, the general 
revisions may be inserted in the AFM, provided the relevant 
information in the general revision is identical to that in these 
flight manual changes, and then these temporary flight manual 
changes may be removed.
    (1) Cessna Temporary FAA Approved Airplane Flight Manual Change 
75FM TC-R11-23, approved June 26, 2012.
    (2) Cessna Temporary FAA Approved Airplane Flight Manual Change 
75FM TC-R11-24, approved June 26, 2012.
    (3) Cessna Temporary FAA Approved Airplane Flight Manual Change 
75FM TC-R11-25, approved June 26, 2012.
    (4) Cessna Temporary FAA Approved Airplane Flight Manual Change 
75FM TC-R11-26, approved June 26, 2012.
    (5) Cessna Temporary FAA Approved Airplane Flight Manual Change 
75FMA TC-R02-03, approved April 10, 2012.
    (6) Cessna Temporary FAA Approved Airplane Flight Manual Change 
75FMA TC-R02-07, approved June 26, 2012.

(i) Parts Installation Prohibition

    As of the effective date of this AD, no person may install an 
altitude/pitot static heater module assembly having P/N 6718477-9, 
P/N 6718477-10, or P/N 9914731-1, on any airplane.

(j) Special Flight Permit

    Special flight permits may be issued in accordance with sections 
21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 
and 21.199) to operate the airplane to a location where the airplane 
can be modified (if the operator elects to do so), provided the 
actions required by paragraph (h) of this AD have been accomplished.

 (k) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Wichita Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in the Related Information 
section of this AD.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.

(l) Related Information

    For more information about this AD, contact Christine Abraham, 
Aerospace Engineer, Electrical Systems and Avionics Branch, ACE-
119W, FAA, Wichita Aircraft Certification Office (ACO), 1801 Airport 
Road, Room 100, Mid-Continent Airport, Wichita, Kansas 67209; phone: 
316-946-4165; fax: 316-946-4107; email: Christine.Abraham@faa.gov.

(m) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Cessna Service Letter SL750-30-08, Revision 1, dated July 
11, 2011.
    (ii) Cessna Temporary FAA Approved Airplane Flight Manual Change 
75FM TC-R11-23, approved June 26, 2012.
    (iii) Cessna Temporary FAA Approved Airplane Flight Manual 
Change 75FM TC-R11-24, approved June 26, 2012.
    (iv) Cessna Temporary FAA Approved Airplane Flight Manual Change 
75FM TC-R11-25, approved June 26, 2012.
    (v) Cessna Temporary FAA Approved Airplane Flight Manual Change 
75FM TC-R11-26, approved June 26, 2012.
    (vi) Cessna Temporary FAA Approved Airplane Flight Manual Change 
75FMA TC-R02-03, approved April 10, 2012.
    (vii) Cessna Temporary FAA Approved Airplane Flight Manual 
Change 75FMA TC-R02-07, approved June 26, 2012.
    (3) For Cessna service information identified in this AD, 
contact Cessna Aircraft Co., P.O. Box 7706, Wichita, Kansas 67277; 
telephone 316-517-6215; fax 316-517-5802; email 
citationpubs@cessna.textron.com; Internet https://www.cessnasupport.com/newlogin.html.
    (4) You may review copies of the service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. 
For information on the availability of this material at the FAA, 
call 425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on February 8, 2013.
Ali Bahrami,
Manager,
    Transport Airplane Directorate, Aircraft Certification Service.
[FR Doc. 2013-04901 Filed 3-6-13; 8:45 am]
BILLING CODE 4910-13-P

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.