Airworthiness Directives; Fokker Services B.V. Airplanes, 23385-23388 [2012-9294]

Download as PDF Federal Register / Vol. 77, No. 76 / Thursday, April 19, 2012 / Rules and Regulations Corporation, Attn: Manager, Commercial Technical Support, Mailstop s581a, 6900 Main Street, Stratford, CT 06614; telephone (800) 562–4409; email tsslibrary@sikorsky.com; or at https:// www.sikorsky.com. You may review a copy of this service information at the FAA, Office of the Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas 76137. (h) Subject Joint Aircraft Service Component (JASC) Code: 7200, Engine (Turbine/Turboprop). Issued in Fort Worth, Texas, on April 9, 2012. Lance T. Gant, Acting Manager, Rotorcraft Directorate, Aircraft Certification Service. [FR Doc. 2012–9298 Filed 4–18–12; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION 14 CFR Part 39 [Docket No. FAA–2011–1226; Directorate Identifier 2011–NM–006–AD; Amendment 39–17001; AD 2012–06–20] RIN 2120–AA64 Airworthiness Directives; Fokker Services B.V. Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. AGENCY: We are adopting a new airworthiness directive (AD) for certain Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This AD was prompted by a report that the fuel crossfeed valves cannot be controlled when only emergency electrical power is available, that an unwanted configuration of the indication logic for the fuel fire shutoff valve was introduced during production, and that current fuel crossfeed indications are based on selection by the flightcrew instead of actual position of the crossfeed valve actuators. This AD requires modifying the crossfeed valve control and power supply, the crossfeed indication logic and power supply, and the indication logic for the fuel fire shutoff valve; modifying the overhead panel; and for certain airplanes, modifying the transfer logic of the center wing fuel tank. We are issuing this AD to prevent failure of an in-flight engine re-light following a double engine flame-out event, which could result in loss of the airplane. DATES: This AD becomes effective May 24, 2012. srobinson on DSK4SPTVN1PROD with RULES VerDate Mar<15>2010 16:05 Apr 18, 2012 Jkt 226001 Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM was published in the Federal Register on November 8, 2011 (76 FR 69163). That NPRM proposed to correct an unsafe condition for the specified products. The MCAI states: Federal Aviation Administration SUMMARY: The Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD as of May 24, 2012. ADDRESSES: You may examine the AD docket on the Internet at https:// www.regulations.gov or in person at the U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC. FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, Washington 98057–3356; telephone (425) 227–1137; fax (425) 227–1149. SUPPLEMENTARY INFORMATION: A recent safety review revealed that the fuel crossfeed valves cannot be controlled when only emergency electrical power is available. This condition, if not corrected, could (in combination with other factors) prevent an in-flight engine re-light following a double engine flame-out event, possibly resulting in loss of the aeroplane. Another review revealed that an unwanted configuration of the fuel fire shut-off valve indication logic had been introduced during production on a limited number of F28 Mark 0100 aeroplanes. Furthermore, most of the current fuel crossfeed indications are based on the crossfeed selection made by the flight crew and not on the actual positions of the crossfeed valve actuators. In combination with other factors, the current crossfeed indications may mislead flight crews, possibly resulting in single engine in-flight shutdowns and/or unnecessary precautionary landings. For the reasons described above, this [EASA] AD requires modifications of the crossfeed valve control and power supply, of the crossfeed indication logic and power supply and of the fuel fire shut-off valve indication logic. * * * * * Required actions also include modifying the overhead panel (introducing provisions for a modified crossfeed indication), and, for certain airplanes, modifying the transfer logic of the center wing fuel tank. You may obtain further information by examining the MCAI in the AD docket. PO 00000 Frm 00013 Fmt 4700 Sfmt 4700 23385 Comments We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM (76 FR 69163, November 8, 2011) or on the determination of the cost to the public. Explanation of Changes Made to This AD We have revised the heading for and the wording in paragraph (i) of this AD; this change has not changed the intent of that paragraph. We have also revised the document citations throughout this AD to more clearly identify the documents and their attachments. Conclusion We reviewed the relevant data and determined that air safety and the public interest require adopting the AD with the changes described previously— and minor editorial changes. We have determined that these minor changes: • Are consistent with the intent that was proposed in the NPRM (76 FR 69163, November 8, 2011) for correcting the unsafe condition; and • Do not add any additional burden upon the public than was already proposed in the NPRM (76 FR 69163, November 8, 2011). Costs of Compliance We estimate that this AD will affect 6 products of U.S. registry. We also estimate that it will take about 86 workhours per product to comply with the basic requirements of this AD. The average labor rate is $85 per work-hour. Required parts will cost about $4,180 per product. Where the service information lists required parts costs that are covered under warranty, we have assumed that there will be no charge for these parts. As we do not control warranty coverage for affected parties, some parties may incur costs higher than estimated here. Based on these figures, we estimate the cost of this AD to the U.S. operators to be $68,940, or $11,490 per product. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations E:\FR\FM\19APR1.SGM 19APR1 23386 Federal Register / Vol. 77, No. 76 / Thursday, April 19, 2012 / Rules and Regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); 3. Will not affect intrastate aviation in Alaska; and 4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains the NPRM (76 FR 69163, November 8, 2011), the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. srobinson on DSK4SPTVN1PROD with RULES Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ VerDate Mar<15>2010 16:05 Apr 18, 2012 Jkt 226001 Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new AD: ■ 2012–06–20 Fokker Services B.V.: Amendment 39–17001. Docket No. FAA–2011–1226; Directorate Identifier 2011–NM–006–AD. (a) Effective Date This airworthiness directive (AD) becomes effective May 24, 2012. (b) Affected ADs None. (c) Applicability This AD applies to Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes, certificated in any category, serial numbers 11244 through 11585 inclusive. (d) Subject Air Transport Association (ATA) of America Code 28: Fuel. (e) Reason This AD was prompted by a report that the fuel crossfeed valves cannot be controlled when only emergency electrical power is available, that an unwanted configuration of the indication logic for the fuel fire shutoff valve was introduced during production, and that current fuel crossfeed indications are based on selection by the flightcrew instead of actual position of the crossfeed valve actuators. We are issuing this AD to prevent failure of an in-flight engine re-light following a double engine flame-out event, which could result in loss of the airplane. (f) Compliance You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. (g) Modifications Within 24 months after the effective date of this AD, modify the crossfeed valve control and power supply, the crossfeed indication logic and power supply, and the indication logic for the fuel fire shutoff valve, in accordance with the Accomplishment Instructions of Fokker Service Bulletin SBF100–28–047, Revision 3, dated May 2, 2011, including the attachments specified in paragraphs (g)(1) through (g)(39) of this AD (*the issue date is not specified on the drawing). (1) Fokker Manual Change Notification— Operational Documentation MCNO–F100– 060, dated June 10, 2011. (2) Fokker Manual Change Notification— Operational Document MCNO–F100–049, Revision 1, dated May 30, 2011. (3) Fokker Drawing D42770, Sheet 6, Issue U*. (4) Fokker Drawing D42780, Sheet 6, Issue T*. (5) Fokker Drawing W41074, Sheet 100, Issue GB*. (6) Fokker Drawing W41074, Sheet 101, Issue FW*. (7) Fokker Drawing W41194, Sheet 010, Issue J*. PO 00000 Frm 00014 Fmt 4700 Sfmt 4700 (8) Fokker Drawing W41194, Sheet 011, Issue U*. (9) Fokker Drawing W41194, Sheet 012, Issue J*. (10) Fokker Drawing W41194, Sheet 013, Issue U*. (11) Fokker Drawing W41194, Sheet 014, Issue S*. (12) Fokker Drawing W41194, Sheet 015, Issue U*. (13) Fokker Drawing W41194, Sheet 017, Issue Q*. (14) Fokker Drawing W41194, Sheet 019, Issue S*. (15) Fokker Drawing W41194, Sheet 020, Issue S*. (16) Fokker Drawing W41319, Sheet 063, Issue DY*. (17) Fokker Drawing W41319, Sheet 064, Issue DY*. (18) Fokker Drawing W41319, Sheet 065, Issue DY*. (19) Fokker Drawing W41319, Sheet 066, Issue DY*. (20) Fokker Drawing W41319, Sheet 067, Issue DW*. (21) Fokker Drawing W41319, Sheet 068, Issue DW*. (22) Fokker Drawing W41319, Sheet 069, Issue DY*. (23) Fokker Drawing W41319, Sheet 070, Issue DW*. (24) Fokker Drawing W41319, Sheet 071, Issue DY*. (25) Fokker Drawing W41319, Sheet 072, Issue DW*. (26) Fokker Drawing W41319, Sheet 073, Issue DW*. (27) Fokker Drawing W41319, Sheet 074, Issue DY*. (28) Fokker Drawing W46211, Sheet 71, Issue DL, dated April 21, 2009. (29) Fokker Drawing W46211, Sheet 74, Issue DN, dated July 16, 2010. (30) Fokker Drawing W46254, Sheet 30, Issue BL, dated March 30, 2009. (31) Fokker Drawing W46254, Sheet 31, Issue BL, dated March 30, 2009. (32) Fokker Drawing W46254, Sheet 32, Issue BL, dated March 30, 2009. (33) Fokker Drawing W46254, Sheet 33, Issue BL, dated March 30, 2009. (34) Fokker Drawing W46254, Sheet 34, Issue BL, dated March 30, 2009. (35) Fokker Drawing W46254, Sheet 35, Issue BL, dated March 30, 2009. (36) Fokker Drawing W46254, Sheet 36, Issue BL, dated March 30, 2009. (37) Fokker Drawing W46254, Sheet 37, Issue BP, dated March 30, 2009. (38) Fokker Drawing W59221, Sheet 161, Issue FC, July 9, 2010. (39) Fokker Drawing W59221, Sheet 162, Issue FC, July 9, 2010. (h) Concurrent Modifications Before or concurrent with the modification specified in paragraph (g) of this AD, do the applicable actions specified in paragraphs (h)(1) and (h)(2) of this AD: (1) For all airplanes: Modify the overhead panel (introduce provisions for a modified crossfeed indication) in accordance with the Accomplishment Instructions of Fokker Proforma Service Bulletin SBF100–28–043, Revision 1, dated March 31, 2009, including E:\FR\FM\19APR1.SGM 19APR1 Federal Register / Vol. 77, No. 76 / Thursday, April 19, 2012 / Rules and Regulations Appendix II, Revision 2, dated July 22, 2010, including the drawings specified in paragraphs (h)(i) through (h)(iv) of this AD, which are attached to Appendix II, Revision 2, dated July 22, 2010 (*the issue date is not specified on the drawing). (i) Fokker Drawing W41194, Sheet 009, Issue F*. (ii) Fokker Drawing W41194, Sheet 016, Issue N*. (iii) Fokker Drawing W41194, Sheet 018, Issue S*. (iv) Fokker Drawing W59221, Sheet 159, Issue ED, dated October 2, 2009. (2) For airplanes with serial numbers 11442 through 11585, equipped with the automatic fuel transfer system: Modify the transfer logic of the center wing fuel tank, in accordance with the Accomplishment Instructions of Fokker Service Bulletin SBF100–28–052, dated June 15, 2009, including the attachments specified in paragraphs (h)(2)(i) through (h)(2)(vii) of this AD. (i) Fokker Manual Change Notification— Operational Documentation MCNO–F100– 052, dated June 15, 2009. (ii) Fokker Manual Change Notification— Maintenance Documentation MCNM–F100– 126, dated June 15, 2009. (iii) Fokker Drawing D42126, Sheet 38, Issue AR, dated October 6, 1993. (iv) Fokker Drawing D42213, Sheet 2, Issue H, dated May 23, 1990. (v) Fokker Drawing D42220, Sheet 60, Issue V, dated September 1, 1991. (vi) Fokker Drawing D42220, Sheet 71, Issue AQ, dated June 7, 1993. (vii) Fokker Drawing D42250, Sheet 23, Issue U, dated April 1993. srobinson on DSK4SPTVN1PROD with RULES (i) Credit for Previous Actions This paragraph provides credit for modifications required by paragraphs (g) and (h) of this AD, if the modifications were performed before the effective date of this AD, using the applicable service bulletins specified in paragraphs (i)(1), (i)(2), (i)(3), and (i)(4) of this AD. (1) Fokker Service Bulletin SBF100–28– 043, including Appendix II, dated March 31, 2009. (2) Fokker Service Bulletin SBF100–28– 047, Revision 2, dated August 4, 2010. (3) Fokker Service Bulletin SBF100–28– 047, Revision 1, dated July 22, 2010. (4) Fokker Service Bulletin SBF100–28– 047, dated May 10, 2010. (j) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM–116, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, Washington 98057– VerDate Mar<15>2010 16:05 Apr 18, 2012 Jkt 226001 3356; telephone (425) 227–1137; fax (425) 227–1149. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. The AMOC approval letter must specifically reference this AD. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (k) Related Information Refer to MCAI European Aviation Safety Agency Airworthiness Directive 2010– 0158R1, dated November 8, 2010, and the service bulletins specified in paragraphs (g) and (h) of this AD, for related information. (l) Material Incorporated by Reference (1) You must use the following service information to do the actions required by this AD, unless the AD specifies otherwise. The Director of the Federal Register approved the incorporation by reference (IBR) of the following service information under 5 U.S.C. 552(a) and 1 CFR part 51: (i) Fokker Proforma Service Bulletin SBF100–28–043, Revision 1, dated March 31, 2009, including Appendix II, Revision 2, dated July 22, 2010, and including the following drawings which are attached to Appendix II, Revision 2, dated July 22, 2010 (*the issue date is not specified on the drawing): (A) Fokker Drawing W41194, Sheet 009, Issue F*. (B) Fokker Drawing W41194, Sheet 016, Issue N*. (C) Fokker Drawing W41194, Sheet 018, Issue S*. (D) Fokker Drawing W59221, Sheet 159, Issue ED, dated October 2, 2009. (ii) Fokker Service Bulletin SBF100–28– 047, Revision 3, dated May 2, 2011, including the following attachments (*the issue date is not specified on the drawing): (A) Fokker Manual Change Notification— Operational Documentation MCNO–F100– 060, dated June 10, 2011. (B) Fokker Manual Change Notification— Operational Document MCNO–F100–049, Revision 1, dated May 30, 2011. (C) Fokker Drawing D42770, Sheet 6, Issue U*. (D) Fokker Drawing D42780, Sheet 6, Issue T*. (E) Fokker Drawing W41074, Sheet 100, Issue GB*. (F) Fokker Drawing W41074, Sheet 101, Issue FW*. (G) Fokker Drawing W41194, Sheet 010, Issue J*. (H) Fokker Drawing W41194, Sheet 011, Issue U*. (I) Fokker Drawing W41194, Sheet 012, Issue J*. (J) Fokker Drawing W41194, Sheet 013, Issue U*. PO 00000 Frm 00015 Fmt 4700 Sfmt 4700 23387 (K) Fokker Drawing W41194, Sheet 014, Issue S*. (L) Fokker Drawing W41194, Sheet 015, Issue U*. (M) Fokker Drawing W41194, Sheet 017, Issue Q*. (N) Fokker Drawing W41194, Sheet 019, Issue S*. (O) Fokker Drawing W41194, Sheet 020, Issue S*. (P) Fokker Drawing W41319, Sheet 063, Issue DY*. (Q) Fokker Drawing W41319, Sheet 064, Issue DY*. (R) Fokker Drawing W41319, Sheet 065, Issue DY*. (S) Fokker Drawing W41319, Sheet 066, Issue DY*. (T) Fokker Drawing W41319, Sheet 067, Issue DW*. (U) Fokker Drawing W41319, Sheet 068, Issue DW*. (V) Fokker Drawing W41319, Sheet 069, Issue DY*. (W) Fokker Drawing W41319, Sheet 070, Issue DW*. (X) Fokker Drawing W41319, Sheet 071, Issue DY*. (Y) Fokker Drawing W41319, Sheet 072, Issue DW*. (Z) Fokker Drawing W41319, Sheet 073, Issue DW*. (AA) Fokker Drawing W41319, Sheet 074, Issue DY*. (BB) Fokker Drawing W46211, Sheet 71, Issue DL, dated April 21, 2009. (CC) Fokker Drawing W46211, Sheet 74, Issue DN, dated July 16, 2010. (DD) Fokker Drawing W46254, Sheet 30, Issue BL, dated March 30, 2009. (EE) Fokker Drawing W46254, Sheet 31, Issue BL, dated March 30, 2009. (FF) Fokker Drawing W46254, Sheet 32, Issue BL, dated March 30, 2009. (GG) Fokker Drawing W46254, Sheet 33, Issue BL, dated March 30, 2009. (HH) Fokker Drawing W46254, Sheet 34, Issue BL, dated March 30, 2009. (II) Fokker Drawing W46254, Sheet 35, Issue BL, dated March 30, 2009. (JJ) Fokker Drawing W46254, Sheet 36, Issue BL, dated March 30, 2009. (KK) Fokker Drawing W46254, Sheet 37, Issue BP, dated March 30, 2009. (LL) Fokker Drawing W59221, Sheet 161, Issue FC, July 9, 2010. (MM) Fokker Drawing W59221, Sheet 162, Issue FC, July 9, 2010. (iii) Fokker Service Bulletin SBF100–28– 052, dated June 15, 2009, including the following attachments: (A) Fokker Manual Change Notification— Operational Documentation MCNO–F100– 052, dated June 15, 2009. (B) Fokker Manual Change Notification— Maintenance Documentation MCNM–F100– 126, dated June 15, 2009. (C) Fokker Drawing D42126, Sheet 38, Issue AR, dated October 6, 1993. (D) Fokker Drawing D42213, Sheet 2, Issue H, dated May 23, 1990. (E) Fokker Drawing D42220, Sheet 60, Issue V, dated September 1, 1991. (F) Fokker Drawing D42220, Sheet 71, Issue AQ, dated June 7, 1993. (G) Fokker Drawing D42250, Sheet 23, Issue U, dated April 1993. E:\FR\FM\19APR1.SGM 19APR1 23388 Federal Register / Vol. 77, No. 76 / Thursday, April 19, 2012 / Rules and Regulations (2) For Fokker Services B.V. service information identified in this AD, contact Fokker Services B.V., Technical Services Dept., P.O. Box 231, 2150 AE Nieuw-Vennep, the Netherlands; telephone +31 (0)252–627– 350; fax +31 (0)252–627–211; email technicalservices.fokkerservices@stork.com; Internet https://www.myfokkerfleet.com. (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, Washington. For information on the availability of this material at the FAA, call 425–227–1221. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at an NARA facility, call 202–741– 6030, or go to https://www.archives.gov/ federal_register/code_of_federal_regulations/ ibr_locations.html. Issued in Renton, Washington, on March 19, 2012. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2012–9294 Filed 4–18–12; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2012–0395; Directorate Identifier 2012–SW–007–AD; Amendment 39–17016; AD 2012–02–51] RIN 2120–AA64 Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule; request for comments. AGENCY: We are publishing a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (Bell) Model 206L, 206L–1, 206L–3, and 206L–4 helicopters with certain main rotor blades installed to reduce the life limit of those blades. This AD is prompted by two accidents and the subsequent investigations that revealed that, in each accident, a main rotor blade failed because of fatigue cracking. These actions are intended to prevent failure of the main rotor blade and subsequent loss of control of the helicopter. srobinson on DSK4SPTVN1PROD with RULES SUMMARY: This AD becomes effective May 4, 2012 to all persons except those persons to whom it was made DATES: VerDate Mar<15>2010 16:05 Apr 18, 2012 Jkt 226001 immediately effective by Emergency AD No. 2012–02–51, issued on February 1, 2012, which contained the requirements of this AD. We must receive comments on this AD by June 18, 2012. ADDRESSES: You may send comments by any of the following methods: • Federal eRulemaking Docket: Go to https://www.regulations.gov. Follow the online instructions for sending your comments electronically. • Fax: 202–493–2251. • Mail: Send comments to the U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590–0001. • Hand Delivery: Deliver to the ‘‘Mail’’ address between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. Examining the AD Docket: You may examine the AD docket on the Internet at https://www.regulations.gov or in person at the Docket Operations Office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the economic evaluation, and other information. The street address for the Docket Operations Office (telephone 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. For service information identified in this AD, contact Bell Helicopter Textron Canada Limited, 12,800 Rue de l’Avenir, Mirabel, Quebec J7J1R4, telephone (450) 437–2862 or (800) 363–8023, fax (450) 433–0272, or at https:// www.bellcustomer.com/files/. You may review a copy of the referenced service information at the FAA, Office of the Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas 76137. FOR FURTHER INFORMATION CONTACT: Sharon Miles, Aerospace Engineer, FAA, Rotorcraft Directorate, Regulations and Policy Group, 2601 Meacham Blvd., Fort Worth, Texas 76137, telephone (817) 222–5110, email sharon.y.miles@faa.gov. SUPPLEMENTARY INFORMATION: Comments Invited This AD is a final rule that involves requirements affecting flight safety, and we did not provide you with notice and an opportunity to provide your comments prior to it becoming effective. However, we invite you to participate in this rulemaking by submitting written comments, data, or views. We also invite comments relating to the economic, environmental, energy, or PO 00000 Frm 00016 Fmt 4700 Sfmt 4700 federalism impacts that resulted from adopting this AD. The most helpful comments reference a specific portion of the AD, explain the reason for any recommended change, and include supporting data. To ensure the docket does not contain duplicate comments, commenters should send only one copy of written comments, or if comments are filed electronically, commenters should submit them only one time. We will file in the docket all comments that we receive, as well as a report summarizing each substantive public contact with FAA personnel concerning this rulemaking during the comment period. We will consider all the comments we receive and may conduct additional rulemaking based on those comments. Discussion Transport Canada Civil Aviation (TCCA) issued TCCA AD No. CF–2011– 44R1, on February 1, 2012, to correct this same unsafe condition on the Bell Model 206 L, L–1, L–3, and L–4 helicopters. TCCA advises that there is no reliable inspection method to detect the cracks on these blades before blade failure and has reduced the life limit on all affected blades from 3,600 hours time-in-service (TIS) to 1,400 hours TIS and mandated removal from service of those blades that exceed the new life limit. Bell has determined that the fatigue cracks occurred as a result of the use by a Bell supplier of unapproved manufacturing processes, which have since been corrected, and are limited to a specific range of part numbers and serial numbers. We issued EAD 2012–02–51 also on February 1, 2012, for Bell Model 206L, 206L–1, 206L–3, and 206L–4 helicopters with certain main rotor blades installed and reduced the life limit on these blades to correct the unsafe condition caused by this fatigue cracking. FAA’s Determination These helicopters have been approved by the aviation authority of Canada and are approved for operation in the United States. Pursuant to our bilateral agreement with Canada, TCCA, its technical representative, has notified us of the unsafe condition described in the TCCA AD. We are issuing this AD because we evaluated all information provided by the TCCA and determined the unsafe condition exists and is likely to exist or develop on other helicopters of these same type designs. Related Service Information Bell Helicopter Alert Service Bulletin No. 206L–09–159 Revision A, dated November 13, 2009, describes E:\FR\FM\19APR1.SGM 19APR1

Agencies

[Federal Register Volume 77, Number 76 (Thursday, April 19, 2012)]
[Rules and Regulations]
[Pages 23385-23388]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2012-9294]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2011-1226; Directorate Identifier 2011-NM-006-AD; 
Amendment 39-17001; AD 2012-06-20]
RIN 2120-AA64


Airworthiness Directives; Fokker Services B.V. Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This AD 
was prompted by a report that the fuel crossfeed valves cannot be 
controlled when only emergency electrical power is available, that an 
unwanted configuration of the indication logic for the fuel fire 
shutoff valve was introduced during production, and that current fuel 
crossfeed indications are based on selection by the flightcrew instead 
of actual position of the crossfeed valve actuators. This AD requires 
modifying the crossfeed valve control and power supply, the crossfeed 
indication logic and power supply, and the indication logic for the 
fuel fire shutoff valve; modifying the overhead panel; and for certain 
airplanes, modifying the transfer logic of the center wing fuel tank. 
We are issuing this AD to prevent failure of an in-flight engine re-
light following a double engine flame-out event, which could result in 
loss of the airplane.

DATES: This AD becomes effective May 24, 2012.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of May 24, 2012.

ADDRESSES: You may examine the AD docket on the Internet at https://www.regulations.gov or in person at the U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE., Washington, DC.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, Washington 98057-3356; telephone (425) 
227-1137; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on November 8, 2011 (76 
FR 69163). That NPRM proposed to correct an unsafe condition for the 
specified products. The MCAI states:

    A recent safety review revealed that the fuel crossfeed valves 
cannot be controlled when only emergency electrical power is 
available.
    This condition, if not corrected, could (in combination with 
other factors) prevent an in-flight engine re-light following a 
double engine flame-out event, possibly resulting in loss of the 
aeroplane.
    Another review revealed that an unwanted configuration of the 
fuel fire shut-off valve indication logic had been introduced during 
production on a limited number of F28 Mark 0100 aeroplanes.
    Furthermore, most of the current fuel crossfeed indications are 
based on the crossfeed selection made by the flight crew and not on 
the actual positions of the crossfeed valve actuators. In 
combination with other factors, the current crossfeed indications 
may mislead flight crews, possibly resulting in single engine in-
flight shutdowns and/or unnecessary precautionary landings.
    For the reasons described above, this [EASA] AD requires 
modifications of the crossfeed valve control and power supply, of 
the crossfeed indication logic and power supply and of the fuel fire 
shut-off valve indication logic.
* * * * *
Required actions also include modifying the overhead panel (introducing 
provisions for a modified crossfeed indication), and, for certain 
airplanes, modifying the transfer logic of the center wing fuel tank. 
You may obtain further information by examining the MCAI in the AD 
docket.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM (76 FR 69163, November 8, 
2011) or on the determination of the cost to the public.

Explanation of Changes Made to This AD

    We have revised the heading for and the wording in paragraph (i) of 
this AD; this change has not changed the intent of that paragraph. We 
have also revised the document citations throughout this AD to more 
clearly identify the documents and their attachments.

Conclusion

    We reviewed the relevant data and determined that air safety and 
the public interest require adopting the AD with the changes described 
previously--and minor editorial changes. We have determined that these 
minor changes:
     Are consistent with the intent that was proposed in the 
NPRM (76 FR 69163, November 8, 2011) for correcting the unsafe 
condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM (76 FR 69163, November 8, 2011).

Costs of Compliance

    We estimate that this AD will affect 6 products of U.S. registry. 
We also estimate that it will take about 86 work-hours per product to 
comply with the basic requirements of this AD. The average labor rate 
is $85 per work-hour. Required parts will cost about $4,180 per 
product. Where the service information lists required parts costs that 
are covered under warranty, we have assumed that there will be no 
charge for these parts. As we do not control warranty coverage for 
affected parties, some parties may incur costs higher than estimated 
here. Based on these figures, we estimate the cost of this AD to the 
U.S. operators to be $68,940, or $11,490 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations

[[Page 23386]]

for practices, methods, and procedures the Administrator finds 
necessary for safety in air commerce. This regulation is within the 
scope of that authority because it addresses an unsafe condition that 
is likely to exist or develop on products identified in this rulemaking 
action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act. We prepared a regulatory evaluation 
of the estimated costs to comply with this AD and placed it in the AD 
docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains the NPRM (76 FR 69163, November 8, 
2011), the regulatory evaluation, any comments received, and other 
information. The street address for the Docket Operations office 
(telephone (800) 647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2012-06-20 Fokker Services B.V.: Amendment 39-17001. Docket No. FAA-
2011-1226; Directorate Identifier 2011-NM-006-AD.

(a) Effective Date

    This airworthiness directive (AD) becomes effective May 24, 
2012.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Fokker Services B.V. Model F.28 Mark 0070 and 
0100 airplanes, certificated in any category, serial numbers 11244 
through 11585 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 28: Fuel.

(e) Reason

    This AD was prompted by a report that the fuel crossfeed valves 
cannot be controlled when only emergency electrical power is 
available, that an unwanted configuration of the indication logic 
for the fuel fire shutoff valve was introduced during production, 
and that current fuel crossfeed indications are based on selection 
by the flightcrew instead of actual position of the crossfeed valve 
actuators. We are issuing this AD to prevent failure of an in-flight 
engine re-light following a double engine flame-out event, which 
could result in loss of the airplane.

(f) Compliance

    You are responsible for having the actions required by this AD 
performed within the compliance times specified, unless the actions 
have already been done.

(g) Modifications

    Within 24 months after the effective date of this AD, modify the 
crossfeed valve control and power supply, the crossfeed indication 
logic and power supply, and the indication logic for the fuel fire 
shutoff valve, in accordance with the Accomplishment Instructions of 
Fokker Service Bulletin SBF100-28-047, Revision 3, dated May 2, 
2011, including the attachments specified in paragraphs (g)(1) 
through (g)(39) of this AD (*the issue date is not specified on the 
drawing).
    (1) Fokker Manual Change Notification--Operational Documentation 
MCNO-F100-060, dated June 10, 2011.
    (2) Fokker Manual Change Notification--Operational Document 
MCNO-F100-049, Revision 1, dated May 30, 2011.
    (3) Fokker Drawing D42770, Sheet 6, Issue U*.
    (4) Fokker Drawing D42780, Sheet 6, Issue T*.
    (5) Fokker Drawing W41074, Sheet 100, Issue GB*.
    (6) Fokker Drawing W41074, Sheet 101, Issue FW*.
    (7) Fokker Drawing W41194, Sheet 010, Issue J*.
    (8) Fokker Drawing W41194, Sheet 011, Issue U*.
    (9) Fokker Drawing W41194, Sheet 012, Issue J*.
    (10) Fokker Drawing W41194, Sheet 013, Issue U*.
    (11) Fokker Drawing W41194, Sheet 014, Issue S*.
    (12) Fokker Drawing W41194, Sheet 015, Issue U*.
    (13) Fokker Drawing W41194, Sheet 017, Issue Q*.
    (14) Fokker Drawing W41194, Sheet 019, Issue S*.
    (15) Fokker Drawing W41194, Sheet 020, Issue S*.
    (16) Fokker Drawing W41319, Sheet 063, Issue DY*.
    (17) Fokker Drawing W41319, Sheet 064, Issue DY*.
    (18) Fokker Drawing W41319, Sheet 065, Issue DY*.
    (19) Fokker Drawing W41319, Sheet 066, Issue DY*.
    (20) Fokker Drawing W41319, Sheet 067, Issue DW*.
    (21) Fokker Drawing W41319, Sheet 068, Issue DW*.
    (22) Fokker Drawing W41319, Sheet 069, Issue DY*.
    (23) Fokker Drawing W41319, Sheet 070, Issue DW*.
    (24) Fokker Drawing W41319, Sheet 071, Issue DY*.
    (25) Fokker Drawing W41319, Sheet 072, Issue DW*.
    (26) Fokker Drawing W41319, Sheet 073, Issue DW*.
    (27) Fokker Drawing W41319, Sheet 074, Issue DY*.
    (28) Fokker Drawing W46211, Sheet 71, Issue DL, dated April 21, 
2009.
    (29) Fokker Drawing W46211, Sheet 74, Issue DN, dated July 16, 
2010.
    (30) Fokker Drawing W46254, Sheet 30, Issue BL, dated March 30, 
2009.
    (31) Fokker Drawing W46254, Sheet 31, Issue BL, dated March 30, 
2009.
    (32) Fokker Drawing W46254, Sheet 32, Issue BL, dated March 30, 
2009.
    (33) Fokker Drawing W46254, Sheet 33, Issue BL, dated March 30, 
2009.
    (34) Fokker Drawing W46254, Sheet 34, Issue BL, dated March 30, 
2009.
    (35) Fokker Drawing W46254, Sheet 35, Issue BL, dated March 30, 
2009.
    (36) Fokker Drawing W46254, Sheet 36, Issue BL, dated March 30, 
2009.
    (37) Fokker Drawing W46254, Sheet 37, Issue BP, dated March 30, 
2009.
    (38) Fokker Drawing W59221, Sheet 161, Issue FC, July 9, 2010.
    (39) Fokker Drawing W59221, Sheet 162, Issue FC, July 9, 2010.

(h) Concurrent Modifications

    Before or concurrent with the modification specified in 
paragraph (g) of this AD, do the applicable actions specified in 
paragraphs (h)(1) and (h)(2) of this AD:
    (1) For all airplanes: Modify the overhead panel (introduce 
provisions for a modified crossfeed indication) in accordance with 
the Accomplishment Instructions of Fokker Proforma Service Bulletin 
SBF100-28-043, Revision 1, dated March 31, 2009, including

[[Page 23387]]

Appendix II, Revision 2, dated July 22, 2010, including the drawings 
specified in paragraphs (h)(i) through (h)(iv) of this AD, which are 
attached to Appendix II, Revision 2, dated July 22, 2010 (*the issue 
date is not specified on the drawing).
    (i) Fokker Drawing W41194, Sheet 009, Issue F*.
    (ii) Fokker Drawing W41194, Sheet 016, Issue N*.
    (iii) Fokker Drawing W41194, Sheet 018, Issue S*.
    (iv) Fokker Drawing W59221, Sheet 159, Issue ED, dated October 
2, 2009.
    (2) For airplanes with serial numbers 11442 through 11585, 
equipped with the automatic fuel transfer system: Modify the 
transfer logic of the center wing fuel tank, in accordance with the 
Accomplishment Instructions of Fokker Service Bulletin SBF100-28-
052, dated June 15, 2009, including the attachments specified in 
paragraphs (h)(2)(i) through (h)(2)(vii) of this AD.
    (i) Fokker Manual Change Notification--Operational Documentation 
MCNO-F100-052, dated June 15, 2009.
    (ii) Fokker Manual Change Notification--Maintenance 
Documentation MCNM-F100-126, dated June 15, 2009.
    (iii) Fokker Drawing D42126, Sheet 38, Issue AR, dated October 
6, 1993.
    (iv) Fokker Drawing D42213, Sheet 2, Issue H, dated May 23, 
1990.
    (v) Fokker Drawing D42220, Sheet 60, Issue V, dated September 1, 
1991.
    (vi) Fokker Drawing D42220, Sheet 71, Issue AQ, dated June 7, 
1993.
    (vii) Fokker Drawing D42250, Sheet 23, Issue U, dated April 
1993.

(i) Credit for Previous Actions

    This paragraph provides credit for modifications required by 
paragraphs (g) and (h) of this AD, if the modifications were 
performed before the effective date of this AD, using the applicable 
service bulletins specified in paragraphs (i)(1), (i)(2), (i)(3), 
and (i)(4) of this AD.
    (1) Fokker Service Bulletin SBF100-28-043, including Appendix 
II, dated March 31, 2009.
    (2) Fokker Service Bulletin SBF100-28-047, Revision 2, dated 
August 4, 2010.
    (3) Fokker Service Bulletin SBF100-28-047, Revision 1, dated 
July 22, 2010.
    (4) Fokker Service Bulletin SBF100-28-047, dated May 10, 2010.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the International 
Branch, send it to ATTN: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, Washington 98057-3356; telephone (425) 
227-1137; fax (425) 227-1149. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify 
your appropriate principal inspector, or lacking a principal 
inspector, the manager of the local flight standards district 
office/certificate holding district office. The AMOC approval letter 
must specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

(k) Related Information

    Refer to MCAI European Aviation Safety Agency Airworthiness 
Directive 2010-0158R1, dated November 8, 2010, and the service 
bulletins specified in paragraphs (g) and (h) of this AD, for 
related information.

(l) Material Incorporated by Reference

    (1) You must use the following service information to do the 
actions required by this AD, unless the AD specifies otherwise. The 
Director of the Federal Register approved the incorporation by 
reference (IBR) of the following service information under 5 U.S.C. 
552(a) and 1 CFR part 51:
    (i) Fokker Proforma Service Bulletin SBF100-28-043, Revision 1, 
dated March 31, 2009, including Appendix II, Revision 2, dated July 
22, 2010, and including the following drawings which are attached to 
Appendix II, Revision 2, dated July 22, 2010 (*the issue date is not 
specified on the drawing):
    (A) Fokker Drawing W41194, Sheet 009, Issue F*.
    (B) Fokker Drawing W41194, Sheet 016, Issue N*.
    (C) Fokker Drawing W41194, Sheet 018, Issue S*.
    (D) Fokker Drawing W59221, Sheet 159, Issue ED, dated October 2, 
2009.
    (ii) Fokker Service Bulletin SBF100-28-047, Revision 3, dated 
May 2, 2011, including the following attachments (*the issue date is 
not specified on the drawing):
    (A) Fokker Manual Change Notification--Operational Documentation 
MCNO-F100-060, dated June 10, 2011.
    (B) Fokker Manual Change Notification--Operational Document 
MCNO-F100-049, Revision 1, dated May 30, 2011.
    (C) Fokker Drawing D42770, Sheet 6, Issue U*.
    (D) Fokker Drawing D42780, Sheet 6, Issue T*.
    (E) Fokker Drawing W41074, Sheet 100, Issue GB*.
    (F) Fokker Drawing W41074, Sheet 101, Issue FW*.
    (G) Fokker Drawing W41194, Sheet 010, Issue J*.
    (H) Fokker Drawing W41194, Sheet 011, Issue U*.
    (I) Fokker Drawing W41194, Sheet 012, Issue J*.
    (J) Fokker Drawing W41194, Sheet 013, Issue U*.
    (K) Fokker Drawing W41194, Sheet 014, Issue S*.
    (L) Fokker Drawing W41194, Sheet 015, Issue U*.
    (M) Fokker Drawing W41194, Sheet 017, Issue Q*.
    (N) Fokker Drawing W41194, Sheet 019, Issue S*.
    (O) Fokker Drawing W41194, Sheet 020, Issue S*.
    (P) Fokker Drawing W41319, Sheet 063, Issue DY*.
    (Q) Fokker Drawing W41319, Sheet 064, Issue DY*.
    (R) Fokker Drawing W41319, Sheet 065, Issue DY*.
    (S) Fokker Drawing W41319, Sheet 066, Issue DY*.
    (T) Fokker Drawing W41319, Sheet 067, Issue DW*.
    (U) Fokker Drawing W41319, Sheet 068, Issue DW*.
    (V) Fokker Drawing W41319, Sheet 069, Issue DY*.
    (W) Fokker Drawing W41319, Sheet 070, Issue DW*.
    (X) Fokker Drawing W41319, Sheet 071, Issue DY*.
    (Y) Fokker Drawing W41319, Sheet 072, Issue DW*.
    (Z) Fokker Drawing W41319, Sheet 073, Issue DW*.
    (AA) Fokker Drawing W41319, Sheet 074, Issue DY*.
    (BB) Fokker Drawing W46211, Sheet 71, Issue DL, dated April 21, 
2009.
    (CC) Fokker Drawing W46211, Sheet 74, Issue DN, dated July 16, 
2010.
    (DD) Fokker Drawing W46254, Sheet 30, Issue BL, dated March 30, 
2009.
    (EE) Fokker Drawing W46254, Sheet 31, Issue BL, dated March 30, 
2009.
    (FF) Fokker Drawing W46254, Sheet 32, Issue BL, dated March 30, 
2009.
    (GG) Fokker Drawing W46254, Sheet 33, Issue BL, dated March 30, 
2009.
    (HH) Fokker Drawing W46254, Sheet 34, Issue BL, dated March 30, 
2009.
    (II) Fokker Drawing W46254, Sheet 35, Issue BL, dated March 30, 
2009.
    (JJ) Fokker Drawing W46254, Sheet 36, Issue BL, dated March 30, 
2009.
    (KK) Fokker Drawing W46254, Sheet 37, Issue BP, dated March 30, 
2009.
    (LL) Fokker Drawing W59221, Sheet 161, Issue FC, July 9, 2010.
    (MM) Fokker Drawing W59221, Sheet 162, Issue FC, July 9, 2010.
    (iii) Fokker Service Bulletin SBF100-28-052, dated June 15, 
2009, including the following attachments:
    (A) Fokker Manual Change Notification--Operational Documentation 
MCNO-F100-052, dated June 15, 2009.
    (B) Fokker Manual Change Notification--Maintenance Documentation 
MCNM-F100-126, dated June 15, 2009.
    (C) Fokker Drawing D42126, Sheet 38, Issue AR, dated October 6, 
1993.
    (D) Fokker Drawing D42213, Sheet 2, Issue H, dated May 23, 1990.
    (E) Fokker Drawing D42220, Sheet 60, Issue V, dated September 1, 
1991.
    (F) Fokker Drawing D42220, Sheet 71, Issue AQ, dated June 7, 
1993.
    (G) Fokker Drawing D42250, Sheet 23, Issue U, dated April 1993.

[[Page 23388]]

    (2) For Fokker Services B.V. service information identified in 
this AD, contact Fokker Services B.V., Technical Services Dept., 
P.O. Box 231, 2150 AE Nieuw-Vennep, the Netherlands; telephone +31 
(0)252-627-350; fax +31 (0)252-627-211; email 
technicalservices.fokkerservices@stork.com; Internet https://www.myfokkerfleet.com.
    (3) You may review copies of the service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, 
Washington. For information on the availability of this material at 
the FAA, call 425-227-1221.
    (4) You may also review copies of the service information that 
is incorporated by reference at the National Archives and Records 
Administration (NARA). For information on the availability of this 
material at an NARA facility, call 202-741-6030, or go to https://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

    Issued in Renton, Washington, on March 19, 2012.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2012-9294 Filed 4-18-12; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.